Delta Temperature Controller DT Series

Transcription

1 Automation for a Changing World Delta Temperature Controller DT Series

2 Features Many Sizes Available: From 48x24 mm to 96x96 mm, all panel sizes comply with international standards Quality Assurance: All temperature controllers adopt an isolated switching power supply 00 ~ 240 VAC input power supply applicable in all countries of the world CE, UL and C-Tick certified Supports Various Sensors: Various built-in sensor input modes: Thermocouple, platinum RTD or linear voltage/current + - Thermocouple (TC) A + B B - Platinum RTD (RTD) Linear current (ma) V + - Linear voltage (V) Various Output Modes: Relay, voltage pulse, linear voltage, and linear current NO Relay NC COM + - Voltage pulse (For driving SSR) + - Linear current (ma) V + - Linear voltage (V) Stable Control: Built-in PID control function, with accurate auto-tuning (AT). PID parameters are automatically calculated, enhancing the stability of the system and accuracy of control PV (Before AT) PV (After AT) Current Transformer (CT): CT can enable the off-line alarm and can detect if the current is overloaded

3 Programmable Control: Max. 8 patterns available, with 8 steps in each pattern. No master controller is required for planning many kinds of temperature control curves Ramp Soak Minute Communication: RS-485 communication interface, supporting MODBUS ASCII/RTU communication HMI PLC MODBUS RTU MODBUS ASCII Safety: The key-locking function and communication protection prevents malfunction Dual Output Control: Able to execute heating and cooling controls at the same time, allowing the system to reach the set temperature quickly Steam Heating Sensor Cooling Water PID 2

4 Products High Speed Intelligent Temperature Controller The Delta temperature controller DT3 series is designed with upgraded hardware and higher specifications as well as smart operation, fast response, easy modularization, plus user-friendly and user-defined function keys. With Self-Tuning and FUZZY temperature control functions, controllers can be installed in open space and confined space applications and are capable of presenting a smooth temperature control curve. In addition, the innovative design enables customers to replace the module with new functions to attain the ultimate in extension flexibility. Remote Control Sets DT3 temperature via analog output of host controller Hotplate Temperature signal input Analog signal ma/v Control output Remote control via analog signal or communication protocols 0~20 ma, 4~20 ma 0~5 V, 0~0 V Various Control Modes Auto Tuning FUZZY Manual / PID Process Control Self Tuning Set value When disturbance occurs PID control FUZZY PID control The FUZZY mode effectively reduces temperature fluctuation PID control FUZZY PID control 3

5 Extension Ability Modular design of functional devices lets users replace the module as needed for application flexibility User-defined Function Keys Menu Auto-tuning Control modes selection RUN/STOP Mode Program hold Large Tri-color LCD Display The st Tri-color LCD temperature controller in Taiwan. Point-to-point Control (Proportional Output ma/v) Sets the Present Value by point-to-point control. Heater Disconnection Detection Measurable up to 00 A Power Dual Output Control Preset temperature is rapidly attained using two sets of outputs for heating and cooling control This function is used to automatically calculate two sets of PID parameters, one for heating and one for cooling Output (Heating Control) Retransmission Output Output 2 (Cooling Control) Present Value Transmission ma/v Current Transfer Inject 4

6 Specifications Input power supply 00 to 240 VAC, 50 / 60 Hz, 24 VDC ±0% Display method LCD. Present Value: red, Set Value: green Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK Input sensors Platinum RTD: Pt00, JPt00 Analog input: 0 to 5 V, 0 to 0 V, 0 to 20 ma, 4 to 20 ma, 0 to 50 mv Control modes PID, PID programmable, FUZZY, Self-tuning, manual, / Display accuracy 0 or digit to the right of the decimal point Sampling rate Analog input: 0.s, Thermocouple or platinum RTD: 0.s Operating Ambient Temperature 0 ~ +50 Operating Relative Humidity 35 to 80% RH (non-condensing) Alarm Outputs The DT3 offers 3 alarm outputs, and each alarm output has 8 alarm modes to choose from in the initial setting mode. When the target temperature exceeds or falls below the set point, the alarm output is enabled. SV Alarm function disabled Alarm Mode Deviation upper- and lower-limit: This alarm output operates when PV value is higher than the set value SV + (AL - H) or lower than the set value SV - (AL - L). Deviation upper-limit: This alarm output operates when PV value is higher than the set value SV + (AL - H). Deviation lower-limit: This alarm output operates when PV value is lower than the set value SV - (AL - L). Absolute value upper- and lower-limit: This alarm output operates when PV value is higher than the set value AL-H or lower than the set value AL - L. Absolute value upper-limit: This alarm output operates when PV value is higher than the set value AL - H. Absolute value lower-limit: This alarm output operates when PV value is lower than the set value AL - L. Hysteresis upper-limit alarm output: This alarm output operates if PV value is higher than the set value SV + (AL - H). This alarm output is when PV value is lower than the set value SV + (AL - L). Hysteresis lower-limit alarm output: This alarm output operates if PV value is lower than the set value SV - (AL - H). This alarm output is when PV value is higher than the set value SV - (AL - L). Disconnection Alarm: This alarm output operates if the sensor connection is incorrect or has been disconnected. CT Alarm: CT is if the value of CT is lower than the value of AL - L or higher than AL - H. CT2 Alarm: CT2 is if the value of CT2 is lower than the value of AL - L or higher than AL - H. When SOAK status (temperature hold) happens to PID program control, alarm output is. When RAMP UP status happens to PID program control, alarm output is. When RAMP DOWN status happens to PID program control, alarm output is. When RUN status happens to PID program control, alarm output is. When HOLD status happens to PID program control, alarm output is. When STOP status happens to PID program control, alarm output is. When END status happens to PID program control, alarm output is. Alarm Output Operation SV - (AL - L) SV AL - L AL - L AL - H AL - L AL - L SV SV - (AL - L) SV AL - L SV + (AL - H) SV + (AL - H) AL - H AL - H AL - H AL - H 5

7 RS-485 Communication DT3 supports baudrate 2,400 to 38,400 bps, MODBUS ASCII/RTU protocol, function code 03H and reads maximum 8 words from the register. Address 000H 00H 002H 003H 005H 006H 007H 008H 009H 00AH 00BH 02H 03H 06H 02AH 02BH 02CH 02DH 03BH 03CH Present value (PV) Set value (SV) Upper limit of temp. range Lower limit of temp. range Control mode Heating/ Cooling control st Heating/ Cooling control cycle nd 2 Heating/ Cooling control cycle Proportional band (PB) Ti value Td value Read/write Output volume Read/write Output 2 volume Regulated temp. value Read/write LED status Read/write key status Panel lockup status CT value AT setting Content Control RUN/STOP setting Measuring unit: 0. scale. The following values read mean error occurs. 8002H: Temperature not yet acquired 8003H: Not connected to sensor 8004H: Incorrect sensor Measuring unit: 0. scale Cannot exceed the default value Cannot fall below the default value 0: PID, : /, 2: Manual, 3: FUZZY 0: Heating/ Heating, : Cooling/ Heating, 2: Heating/ Cooling, 3: Cooling/ Cooling 0. ~ 99 sec. 0. ~ 99 sec. 0. ~ ~ ~ 9999 Unit: 0.%, only valid in manual control mode Unit: 0.%, only valid in manual control mode ~ +99.9, Unit: 0. b0: ALM3, b: ALM2, b2: F, b3: C, b4: ALM, b5: OUT2, b6: OUT, b7:at b0: Set, b: Select, b2: Up, b3: Down, 0: it 0: Normal, : Fully locked, : SV adjustable Unit: 0.A 0: (default), : Definition 0: STOP, : RUN (default), 2: END (program), 3: HOLD (program) 6

8 Parameters Operation Regulation Mode SET for less than 3 sec SET Operation Mode SET for more than 3 sec SET Initial Setting Mode Regulation Mode Operation Mode Initial Setting Mode Auto-tuning (when CTRL set in PID or FUZZY and in RUN mode) Self-tuning switch (set when in PID control and the TUNE parameter = ST) Select the nth (n = 0 ~ 5) PID. When n = 6, PID is autoselected. Set up PID control offset Set up start step (when in programmable control) Set up FUZZY gain value Set up the position of decimal point Set up FUZZY Deadband Lock the keys Adjust Output hysteresis (when in / control) Use to set up target temperature Control loop RUN or STOP Set up start pattern (when in PID programmable control and ) Set up upper limit of Alarm Set up input type Set up temperature unit (not displayed when in analog input) Set up upper temperature limit Set up lower temperature limit Select control modes Select SV control modes Set up waiting temperature (when in programmable control) Adjust Output 2 hysteresis (when in / control) Control cycle for Output (except in / control) Control cycle for Output 2 (except in / control) Ratio of Output against Output 2 when in dual output control (set when in PID and dual output control) Set up deadband (when in dual output) Set up lower limit of Alarm Set up upper limit of Alarm 2 Set up lower limit of Alarm 2 Set up upper limit of Alarm 3 Set up lower limit of Alarm 3 Set up waiting time (when in programmable control) Set up start slope (when in programmable control) Select pattern to be edited Select AT or ST Select heating, cooling or dual output heating and cooling Set up input filter factor Record highest temperature of Alarm Set up input filter range Record lowest temperature of Alarm Adjust input compensation Record highest temperature of Alarm 2 Adjust input gain Record lowest temperature of Alarm 2 Set up rising slope (when CRTS = SLOP) Record highest temperature of Alarm 3 Set up reverse alarm output Set up Remote type Set up Alarm mode Set up Alarm options Set up Alarm delay Adjust upper limit compensation for analog Output * Record lowest temperature of Alarm 3 Select auxiliary function 7

9 Regulation Mode Operation Mode Initial Setting Mode Adjust lower limit compensation for analog Output * Adjust upper limit compensation for analog Output 2* Adjust lower limit compensation for analog Output 2* Adjust upper limit compensation for Retransmission* Adjust lower limit compensation for Retransmission* Adjust Remote gain Adjust Remote compensation Set up EVENT function Set up EVENT2 function Display and adjust Output volume Display and adjust Output 2 volume Set up upper limit percentage for Output Set up lower limit percentage for Output Set up upper limit percentage for Output 2 Set up lower limit percentage for Output 2 CT CT2 Display current measured at Display current measured at Enable/disable communication write-in Select ASCII or RTU format Set up communication address Set up baudrate Set up data length Set up stop bit Set up parity bit Set up EVENT3 function to return to auto-tuning to return to set up target temperature to return to set up input type * scale = μa; scale = mv PID mode: Any of the 6 PID groups can be selected. When n = 6, the program will automatically select the PID group that is the closest to the target temperature. Select the nth PID (n = 0 ~ 5) Set up the 0 PID temperature value Set up the 0 th proportional band value th Set up the 0 Ti value th Set up the 5 PID temperature value Set up the 5 th proportional band value th Set up the 5 Ti value th th Set up the 0 Td value th Set up the 5 Td value th 0 ~ 5 PID Set up the 0 PID integral deviation th to return to PID deviation Set up the 5 PID integral deviation th to return to PID deviation Patterns and steps: Edit in parameter. Take editing pattern 0 for example: Select the pattern number to be edited Select number to select Exit pattern and step editing and switch to to continue the setup process Edit temperature for Step 0 Select actual number of steps when the program is executing Edit time for Step 0 (time unit: hr, min) Set up Step 0 ~ 5 in order Edit temperature for Step 5 Edit time for Step 5 to set up actual step numbers Set up additional cycles (0 ~ 99) for the pattern execution Set up link pattern. refers to the program end. to return to select the pattern number to be edited 8

10 Products DTK Series is a new temperature controller with a high cost-performance ratio. It greatly decreases development costs and time, and improves the functions of temperature control systems. With a length of only 60 mm and high resolution LCD display, it is easy for operators to monitor the temperatures of any environment or occasion. New generation of intelligent temperature controller Features High resolution LCD display Length shortened to 60 mm High speed sampling time 00 ms CE certified Description A PV : Present Value D E F A B C B SV : Set Value C : Celsius, Fahrenheit temperature indicator D 2 : ALM, ALM2 alarm output indicator E A/M : Auto-tuning and manual modes indicator F OUT OUT2 : Output indicator G Select / Set key G G H H H Value adjustment key 9

11 Electrical Specifications Power supply Display Input temperature sensors Control methods Display scale Sampling rate 00 ~ 240 VAC, 50 / 60 Hz LCD display. PV : red, SV : green Thermocouple : K, J, T, E, N, R, S, B, L, U, TXK Platinum RTD : Pt00, JPt00 RTD : Cu50, Ni20 /, PID, Manual digit after decimal point, or no decimal point Thermocouple or platinum RTD : 0. second Ambient temperature 0 ~ +50 C Ambient humidity 35 ~ 80% RH (non-condensing) Alarm Outputs The DTK Series offers 2 alarm outputs, and each alarm output has 9 alarm modes to choose from in the initial setting mode. When the target temperature exceeds or falls below the set point, the alarm output is enabled. SV Alarm Mode Alarm Output Operation 0 Alarm function disabled Deviation upper- and lower-limit : This alarm output operates when PV value is higher than the set value SV + (AL - H) or lower than the set value SV - (AL - L). SV - (AL - L) SV SV + (AL - H) Deviation upper-limit : This alarm output operates when PV value is higher than the set value SV + (AL - H). SV SV + (AL - H) Deviation lower-limit : This alarm output operates when PV value is lower than the set value SV - (AL - L). SV - (AL - L) SV Absolute value upper- and lower-limit : This alarm output operates when PV value is higher than the set value AL - H or lower than the set value AL - L. AL - L AL - H 5 Absolute value upper-limit : This alarm output operates when PV value is higher than the set value AL - H. AL - H 6 Absolute value lower-limit : This alarm output operates when PV value is lower than the set value AL - L. AL - L Hysteresis upper-limit alarm output : This alarm output operates if PV value is higher than the set value SV+ (AL - H). This alarm output is when PV value is lower than the set value SV + (AL - L). AL - L AL - H Hysteresis lower-limit alarm output : This alarm output operates if PV value is lower than the set value SV - (AL - H). This alarm output is when PV value is higher than the set value SV - (AL - L). AL - H AL - L Disconnection alarm : This alarm output operates if the sensor connection is incorrect or has been disconnected. 0

12 Parameters Operation Regulation Mode SET for less than 3 sec SET Operation Mode SET for more than 3 sec SET Initial Setting Mode Regulation Mode Operation Mode Initial Setting Mode Auto - tuning ( when in PID control and RUN mode ) Use temperature to set up target Set up input type Set proportion band Control loop RUN or STOP Set up temperature unit Set integration time Set up the position of decimal point Set up upper temperature limit Set derivative time Lock the keys Set up lower temperature limit Set up PID control offset Set up upper limit of Alarm Select control modes Adjust Output hysteresis (when in / control) Set up lower limit of Alarm Select heating, cooling or dual output heating and cooling Adjust Output 2 hysteresis (when in / control) OUT HEAT: Heating control cycle for Output (when Ctrl = PID/FUZZY/MANUAL) Set up upper limit of Alarm 2 Set up Alarm mode Set up lower limit of Alarm 2 Set up Alarm options *3 OUT COOL: Cooling control cycle for Output (when Ctrl = PID/FUZZY/MANUAL) OUT2 HEAT: Heating control cycle for Output 2 (when Ctrl = PID/FUZZY/MANUAL) OUT2 COOL: Cooling control cycle for Output 2 (when Ctrl = PID/FUZZY/MANUAL) Ratio of Output against Output 2 when in dual output control (set when in PID control) Set up deadband Set up input filter factor Set up input filter range Adjust input compensation * Adjust input gain * Adjust upper limit compensation for analog Output *2 Display and adjust Output volume Display and adjust Output 2 volume Set up upper limit percentage for Output Set up lower limit percentage for Output Set up upper limit percentage for Output 2 Set up lower limit percentage for Output 2 Set up Alarm delay *4 Set up Alarm 2 mode Set up Alarm 2 options *3 Set up Alarm 2 delay *4 Adjust lower limit compensation for analog Output *2 to return to auto-tuning to return to set up target temperature to return to set up input type

13 * Alarm is automatically switched to output control 2 when selecting dual output mode * Set up upper / lower limit percentage for output / 2 volume : set output permission ranges. E.g. upper and lower limit percentage are respectively set as 90 and 20, output volume will be limited to 20% ~ 90%. *. Offset Present value : Use and. Present value = measured value x ( + /.000) +. *2. scale = μa *3. Set up alarm standby : set corresponding Y value as xxxy (Y = 0 : normal / Y = : standby) Set up reverse alarm output : set corresponding Y value as xxyx (Y = 0 : forward / Y = : backward) Set up Hold output : set corresponding Y value as xyxx (Y = 0 : normal / Y = : Hold) *4. Set up alarm delay : The alarm operates after reaching alarm delay time (recalculating time if discontinuity occurs in the process) Temperature Sensors and Temperature Range Input sensors Display Temperature Range Input sensors Display Temperature Range Platinum RTD: Pt ~ 850 ºC Thermocouple E 0 ~ 600 ºC Platinum RTD: JPt00-00 ~ 400 ºC Thermocouple T -200 ~ 400 ºC Copper resistance: Cu50-50 ~ 50 ºC Thermocouple J -00 ~ 850 ºC RTD Ni20-80~300 ºC Thermocouple K -200 ~,300 ºC Thermocouple B 00 ~,800 ºC Thermocouple L -200 ~ 850 ºC Thermocouple S 0 ~,700 ºC Thermocouple U -200 ~ 500 ºC Thermocouple R 0 ~,700 ºC Thermocouple Txk -200 ~ 800 ºC Thermocouple N -200 ~,300 ºC Panel Sizes Terminal Wiring Diagram Models Sizes (W H) mm 45 mm mm 9.5 mm mm 68 mm L 00~240VAC 50/60 Hz 5VA N 3A 250 V AC COM ALM RTD + + OUT Tc

14 Products Standard Type DTA is designed for practical applications, offering the 3 most frequently adopted output types in the market. DTA has many user-friendly functions built-in and a handy transmission structure, ensuring fast and stable data transmission. Optional functions: RS-485 communication interface (MODBUS ASCII/RTU, 2,400 ~ 38,400 bps), CT (current transformer) Electrical Specifications Power supply Voltage range Power consumption Display Input temperature sensors Display scale Control methods Output types Sampling rate Communication Communication protocol Vibration resistance Shock resistance Ambient temperature Storage temperature Altitude Ambient humidity Waterproof degree 00 ~ 240 VAC, 50 / 60 Hz 85 ~ 0% rated voltage 5 VA Max. 2-line 7-segment LED display, PV: red; SV: green Thermocouple: K, J, T, E, N, R, S, B, U, L, TXK Platinum RTD: Pt00, JPt00 0.% full scale PID, /, Manual Relay: 250 VAC, 5 A, SPDT (DTA4848: SPST) Voltage pulse: 4 VDC, Max. output current: 40 ma Current: DC 4 ~ 20 ma (Load resistance: < 600 W) 0.5 second RS-485 digital communication, 2,400 ~ 38,400 bps (optional) MODBUS protocol, ASCII/RTU format (optional) 0 ~ 55 Hz, 0 m/s² for 0 mins in X, Y, Z direction Max. 300 m/s², 3 times in each of 3 axes, 6 directions 0 ~ ~ +65 < 2,000 m 35 ~ 85% RH (non-condensing) IP65 3

15 Advanced Type Compared to the DTA, DTB has an added linear voltage output and adopts dual-loop output control, and is able to execute heating and cooling controls at the same time in a temperature control system. DTB series has a built-in RS-485 communication interface (MODBUS ASCII/RTU, 2,400 ~ 38,400 bps). The programmable PID control function allows the DTB to set up 64 sets of temperature and control times. Optional functions: CT (current transformer), output by alarm. EVENT function, switching between 2 SVs by using PLC or switches. Valve models are able to adjust the openness of valves depending on the SV. Electrical Specifications Power supply Voltage range Power consumption Display Input temperature sensors Display scale Control methods Output types Sampling rate Communication Communication protocol Vibration resistance Shock resistance Ambient temperature Storage temperature Altitude Ambient humidity Waterproof degree 00 ~ 240 VAC, 50 / 60 Hz 85 ~ 0% rated voltage < 5 VA 2-line 7-segment LED display, 4 digits available, PV: red, SV: green Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK Platinum RTD: Pt00, JPt00 Analog input: 0 ~ 5 V, 0 ~ 0 V, 0 ~ 20 ma, 4 ~ 20 ma, 0 ~ 50 mv digit after decimal point, or no decimal point PID, programmable PID, /, Manual Relay: SPDT (DTB4848/4824: SPST), Max. load: 250 VAC, Resistive load: 5 A Voltage pulse: 4 VDC, Max. output current: 40 ma Current: DC 4 ~ 20 ma (Load resistance: < 600 WΩ) Analog voltage: 0 ~ 0 V Analog input: 0.5 second, Thermocouple or platinum RTD: 0.4 second RS-485 digital communication, 2,400 ~ 38,400bps MODBUS protocol, ASCII/RTU format 0 ~ 55 Hz, 0 m/s² for 0 mins in X, Y, Z direction Max. 300 m/s², 3 times in each of 3 axes, 6 directions 0 ~ ~ +65 < 2,000 m 35 ~ 85% RH (non-condensing) IP65 4

16 Products Modular Type DTC features a modular and wire-saving structure, and is able to monitor many temperature points by parallel and modular extension. The user is able to set up a suitable output method according to actual demand. The built-in password protection prevents unauthorized operation or malicious damage from staff. DTC series has a built-in RS-485 communication interface (MODBUS ASCII/RTU, 2,400 ~ 38,400 bps). The programmable PID control function allows the DTC to set up 64 sets of temperature and control times. DTC also supports 3 levels of password protection, synchronous communication protocol and auto ID setup. Electrical Specifications Power supply Voltage range Power consumption Input temperature sensors Control methods Output types Sampling rate Communication Communication protocol Vibration resistance Shock resistance Ambient temperature Storage temperature Altitude Ambient humidity 24 VDC, isolated switching power supply 90 ~ 0% rated voltage 3 W + 3 W x number of DTC2000 controllers connected in parallel (Max. 7) Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK Platinum RTD: Pt00, JPt00 Linear current: 0 ~ 5 V, 0 ~ 0 V, 0 ~ 20 ma, 4 ~ 20 ma, 0 ~ 50 mv PID, programmable PID, /, Manual Relay: SPST, Max. load: 250 V AC, Resistive load: 3 A Voltage pulse: 2 VDC, Max. output current: 40 ma Current: DC 4 ~ 20 ma (Load resistance: < 500 WΩ) Analog voltage: 0 ~ 0 V (Load resistance: >,000 WΩ) Analog input: 0.5 second, Thermocouple or platinum RTD: 0.4 second RS-485 digital communication, 2,400 ~ 38,400 bps MODBUS protocol, ASCII/RTU format 0 ~ 55 Hz, 0 m/s 2 for 0 mins in X, Y, Z direction Max. 300 m/s², 3 times in each of 3 axes, 6 directions 0 ~ ~ +65 < 2,000 m 35 ~ 85% RH (non-condensing) 5

17 Economical Type DTD series offers PID, programmable PID, / and Manual control modes and supports alarm output with 8 alarm modes, which reduces cost but enhances functions. The programmable PID control function allows the DTD to set up 8 sets of temperature and control times. Electrical Specifications Power supply Voltage range Power consumption Display Input temperature sensors Display scale Control methods Output types Sampling rate Vibration resistance Shock resistance Ambient temperature Storage temperature Altitude Ambient humidity Waterproof degree 00 ~ 240 VAC, 50 / 60 Hz 85 ~ 0% rated voltage 6 VA Max. 7-segment LED display, PV: red, SV: green Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK Platinum RTD: Pt00, JPt00 Copper resistance: Cu50 Current: 0 ~ 20 ma, 4 ~ 20 ma Voltage: 0 ~ 5 V, 0 ~ 0 V, 0 ~ 70 mv K2, J2, T2, Pt00-2, JPt00, Cu50: 0., Others: PID, programmable PID, /, Manual Relay: 250 VAC, 5 A, SPST Voltage pulse: 4 VDC, Max. output current: 40 ma 0.4 second (analog input and sensor input) 0 ~ 55 Hz, 0 m/s 2 for 0 mins in X, Y, Z direction Max. 300 m/s², 3 times in each of 3 axes, 6 directions 0 ~ ~ +65 < 2,000 m 35 ~ 85% RH (non-condensing) IP65 6

18 Products Multi-Channel Modular Type DTE series is a multi-channel modular type temperature controller. The DTE0T supports 8 thermocouple inputs and the DTE0P supports 6 platinum RTD inputs. The DTE series is installed on DIN rail, and each channel operates independently. DTE series offers many optional output modules (relay, voltage pulse, current and linear current). The built-in RS wire communication allows transmission of up to 5,200 bps. The programmable PID control function allows the DTE to set up 64 sets of temperature and control times. Maximum 7 DTC2000 controllers are extendable to DTE, and DTE supports the same synchronous communication protocol and auto ID setup which DTC supports. Electrical Specifications Power supply Voltage range Power consumption Input temperature sensors Control methods Output types Sampling rate Communication Communication protocol Vibration resistance Shock resistance Ambient temperature Storage temperature Altitude Ambient humidity 24 VDC, isolated switching power supply 90 ~ 0% rated voltage Max. 0 W + 3 W + 3 W x number of DTC2000 controllers connected in parallel (Max. 7) Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK Platinum RTD: Pt00, JPt00 Copper resistance: Cu50 PID, programmable PID, /, Manual Relay: SPST, Max. load: 250 V AC, Resistive load: 3 A Voltage pulse: 2 VDC, Max. output current: 40 ma Current: DC 4~20 ma (Load resistance: < 500 WΩ) Analog voltage: 0 ~ 0 V (Load resistance: >,000 Ω) Thermocouple or platinum RTD:.0 second/all inputs RS-485 digital communication, 2,400 ~ 5,200 bps MODBUS protocol, ASCII/RTU format 0 ~ 55 Hz, 0 m/s² for 0 mins in X, Y, Z direction Max. 300 m/s², 3 times in each of 3 axes, 6 directions 0 ~ ~ +65 < 2,000 m 35 ~ 85% RH (non-condensing) 7

19 Valve Type DTV series is designed for electronic valve applications. It is user-friendly and easy to use. DTV has built-in MODBUS communication, which allows handier data collection. DTV also features: Auto/manual mode switching by a single key "Left" key makes the parameter setting faster Real-time output percentage display, for the user to check the openness of the valve 2 alarm outputs, 7 alarm modes RS-485 communication interface for DTV to monitor and collect data from other temperature controllers on the network Electrical Specifications Power supply Voltage range Power consumption Display Input temperature sensors Display scale Control methods Output types Sampling rate Communication Communication protocol Vibration resistance Shock resistance Ambient temperature Storage temperature Altitude Ambient humidity Waterproof degree 00 ~ 240 VAC, 50 / 60 Hz 85 ~ 0% rated voltage < 5 VA 2-line 7-segment LED display, 4-bit or 2-bit valve openness display available PV: red, SV & openness of valve: green Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK Platinum RTD: Pt00, JPt00 Analog input: 0 ~ 5 V, 0 ~ 0V, 0 ~ 20 ma, 4 ~ 20 ma, 0 ~ 50 ma digit after decimal point, or no decimal point PID, programmable PID, /, Manual Relay: SPST Max. load: 250 VAC; resistive load: 5 A Analog input: 0.5 second; thermocouple or platinum RTD: 0.4 second RS-485 digital communication, 2,400 ~ 38,400 bps MODBUS protocol, ASCII/RTU format 0 ~ 55 Hz, 0 m/s² for 0 mins in X, Y, Z direction Max. 300 m/s², 3 times in each of 3 axes, 6 directions 0 ~ ~ +65 < 2,000 m 35 ~ 85% RH (non-condensing) IP65 8

20 Ordering Information Series Name Panel size (W x H) Output options Power supply Output 2 options Optional function Optional function 2 Optional function 3 Delta DT3 Series Temperature Controller 20: 4848: /6 DIN W48 x H48 mm 30: 7272: W72 x H72 mm R: Relay, 250 VAC, 5A V: Voltage pulse, 2V +0 to 20% A: AC 00 to 240V D: DC 24 V R: Relay, 250 VAC, 5A V: Voltage pulse, 2V +0 to 20% 40: 4896: /8 DIN W48 x H96 mm 60: 9696: /4 DIN W96 x H96 mm C: DC current, 4 to 20mA L: Linear voltage, 0 to 0 VDC C: DC current, 4 to 20mA L: Linear voltage, 0 to 0 VDC 0: None, : Event input 3, 2: RS-485 communication 0: None, : Event input 2, 2: CT input 2, 3: Retransmission output 0: None, : Event input, 2: CT input, 3: Remote setup input D T 3 - Accessories Option Accessories Delta DT3 Series Temperature Controller 20ESTD: DT320 EXTENSI without RS-485 & EV3 20ECOM: DT320 EXTENSI include RS EEV3: DT320 EXTENSI include EVENT3 40ESTD: DT340/DT360 EXTENSI without RS-485 & EV3 40ECOM: DT340/360 EXTENSI include RS EEV3: DT340/360 EXTENSI include EVENT3 DT330 is a replacement for DTA7272 (with basic function). It has less extension function. DT330 A-0 has output, alarm output, and has no extension functions DT330 A has output, 2 alarm outputs, but no extension functions (similar to DTA7272 0) DT330 A-0000 has extension board without communication function. Functional extension card is an optional part DT330 A-0200 has output, 2 alarm outputs, and has no extension functions. It supports RS-485 communication function (similar to DTA7272 ) R: Relay Output V: DC Voltage Pulse Output C: DC Current Output L: DC Linear Voltage Output EVENT: Event Input CTI: CT Input RETRANS: Retransmission REMOTE: Remote set point CT30A: 30A CT CT00A: 00A CT Series Name Panel size (W x H) 5 Output options Delta DTK Series Temperature Controller 4848: W48 H48 mm 7272: W72 H72 mm 4896: W48 H96 mm R: Relay, 250 VAC, 5 A V: Voltage Pulse, 2 VDC +0~20% C: DC Current Output 4 ~ 20 ma 6 7 Optional function 0: Alarm output 02: 2 Alarm outputs Series Name Panel size (W x H) 5 Output 6 Communication (optional) 7 CT (optional) Delta DTA Series Temperature Controller 4848: /6 DIN W48 x H48 mm 4896: /8 DIN W48 x H96 mm 9696: /4 DIN W96 x H96 mm R: Relay, SPST (4848: SPST), 250 VAC, 5A V: Voltage pulse, 4V +0% ~ -20% (Max. 40mA) 0: N/A : N/A 7272: W72 x H72 mm 9648: W96 x H48 mm C: Current, 4~20mA : RS-485 communication T: With CT (only DTA7272R0) 9

21 Series Name Panel size (W x H) 5 Output options 6 Output 2 options 7 Optional function Delta DTB Series Temperature Controller 4824: /32 DIN W48 x H24 mm 4848: /6 DIN W48 x H48 mm R: Relay, SPDT (4824/4848: SPST), 250 VAC, 5A V: Voltage pulse: 4V +0% ~ -20% C: DC current: 4 ~ 20mA L: Linear voltage: 0 ~ 5V, 0 ~ 0 VDC R: Relay, SPDT (4824/4848: SPST), 250 VAC, 5A V: Voltage pulse: 4V +0% ~ -20% : Without CT, without EVENT input T: With CT, without EVENT input *DTB4824 has no optional function and no extra alarm output. Output 2 can be set to alarm output. nd *DTB4848 has only optional alarm output. Output 2 can be set to the 2 alarm output. *DTB9696 has optional valve control function. Model name: DTB9696RRV. 4896: /8 DIN W48 x H96 mm 9696: /4 DIN W96 x H96 mm E: Without CT, with EVENT input V: Valve control Series Name Controller type Number of auxiliary outputs Optional function Output Delta DTC Series Temperature Controller : Main unit 2: Extension unit 0: Standard 2 outputs, no auxiliary output 00: Standard function 0: With CT input R: Relay, SPST, 250 VAC, 3A V: Voltage pulse, 2V +0% ~ -20% C: Current, 4 ~ 20mA L: Linear voltage, 0 ~ 0V Series Name Delta DTD Series Temperature Controller Panel size (W x H) Output Optional function 4848: /6 DIN W48 x H48 mm 4896: /8 DIN W48 x H96 mm R: Relay, SPST, 250 VAC, 5A V: Voltage pulse, 4V +0% ~ -20% (Max. 40mA) 0: N/A 7272: W72 x H72 mm Series Name Controller type Optional function Delta DTE Series Temperature Controller : Main unit 2: Accessory 0T: 4-channel TC (main unit, accessory) 0P: 3-channel PT (main unit, accessory) 0V: 4 channels of voltage pulse output 0C: 4 channels of linear current output 0R: 4 channels of relay output 0L: 4 channels of linear voltage output 0D: 4 digital inputs & 4 digital outputs CT: 4 channels of current transformers DS: Display & setup module Series Name 3 4 Panel size (W x H) Output Delta DTV Series Temperature Controller 4896: /8 DIN W48 x H96 mm 9696: /4 DIN W96 x H96 mm R: Relay, SPDT, 250 VAC, 5A 20

22 Dimensions Dimensions are in mm mm 44.0 mm 24.0 mm 2.85 mm 48.0 mm 3.4 mm 99.8 mm 95.7 mm 98.2 mm 9.0 mm SET 48.0 mm 2.8 mm 79.2 mm mm 48.0 mm 9.5 mm 80.0 mm mm 72.0 mm 74.0 mm mm 72.0 mm 3.80 mm mm 2

23 Dimensions are in mm 9.0 SET mm 98.0 mm 90.8 mm UGV DTA mm 5.8 mm 79.2 mm DTC DTE

24 Industrial Automation Headquarters Delta Electronics, Inc. Taoyuan Technology Center 8 Xinglong Road, Taoyuan District, Taoyuan City 33068, Taiwan (R.O.C.) TEL: / FAX: Asia Delta Electronics (Jiangsu) Ltd. Wujiang Plant Jiangxing East Road, Wujiang Economic Development Zone Wujiang City, Jiang Su Province, P.R.C TEL: / FAX: Delta Greentech (China) Co., Ltd. 238 Min-Xia Road, Pudong District, ShangHai, P.R.C TEL: / FAX: Delta Electronics (Japan), Inc. Tokyo Office 2--4 Minato-ku Shibadaimon, Tokyo , Japan TEL: / FAX: Delta Electronics (Korea), Inc. 5, Byucksan Digital Valley 6-cha, Gasan-dong, Geumcheon-gu, Seoul, Korea, TEL: / FAX: Delta Electronics Int l (S) Pte Ltd. 4 Kaki Bukit Ave, #05-05, Singapore TEL: / FAX: Delta Electronics (India) Pvt. Ltd. Plot No 43 Sector 35, HSIIDC Gurgaon, PIN 2200, Haryana, India TEL : / FAX : Americas Delta Products Corporation (USA) Raleigh Office P.O. Box 273,50 Davis Drive, Research Triangle Park, NC 27709, U.S.A. TEL: / FAX: Delta Greentech (Brasil) S.A. Sao Paulo Office Rua Itapeva, 26-3 andar Edificio Itapeva One-Bela Vista São Paulo-SP-Brazil TEL: / FAX: Europe Delta Electronics (Netherlands) B.V. Eindhoven Office De Witbogt 20, 5652 AG Eindhoven, The Netherlands TEL: +3 (0) / FAX: +3 (0) *We reserve the right to change the information in this catalogue without prior notice. DELTA_IA-SS_DT_C_EN_20607