Installation & Weatherproofing Guide for ENCOM Broadband Radios
|
|
- Brian Riley
- 5 years ago
- Views:
Transcription
1 Installation & Weatherproofing Guide for ENCOM Broadband Radios
2 Read the following instructions before proceeding with your ENCOM Wireless Radio installation. Keep these instructions in safe location for referral and ensure that you heed all warnings set out within this document. Use only the accessories and attachments specified by the manufacturer. Any and all servicing of the radio is to be completed by a qualified ENCOM Wireless Technician. Any change or modification not expressly written in this manual is not approved by ENCOM Wireless and will result in the warranty of your radio unit and hardware being void. Failure to follow the above points and instructions outlined in this manual will result in the warranty being void for your ENCOM Wireless radio and hardware. Page 2
3 Table of Contents 1.0 Equipment Checklist Radio Site Surveys Fishing Ethernet Cable... 4 Ethernet Cable Pin-outs Ethernet Cable Termination Preparing your Ethernet Cable... 5 Weatherproofing ENCOM Broadband Radios Broadband 4.9GHz/5.8 GHz/BB58N2 and ENERGY IPON Connector Mounting Your ENCOM Broadband Radio Approved Installation of ENCOM Integrated Radios Approved Installation of ENCOM Non-Integrated Radios Non-Integrated ENCOM Radio Polarization Weatherproofing Non-Integrated Broadband Radio Sealing the Antenna Connection Points ENCOM Approved Seal Using Heat Shrink Page 3
4 1.0 Equipment Checklist Identify the following equipment has been received with your ENCOM broadband radio: ü ü ü ü Power Over Ethernet (P.O.E) adapter 150-ft Ethernet cable 6-ft Ethernet Crossover Cable AC Power Cord The following equipment is also needed for the installation of your ENCOM broadband radio: ü Heat Shrink Tubing 2.0 Radio Site Surveys Each radio installation is unique due to the physical environment, radio network configuration and antenna configuration. A site survey is highly recommended to determine the best RF coverage, the optimal placement and location of the radios, and to ensure that the highest network performance is achieved. Failure to perform a site survey can result in degraded performance on the RF network. 3.0 Fishing Ethernet Cable Dirt and debris can reside inside the conduit unit that houses the cables for an intersection. When it is required that the 150ft Ethernet cable is to be fished through the conduit, the cable end (RJ45 jack) must be protected against any damage to it, including any exposure to weather elements. The cable end must remain free of debris, dirt and be clean and dry before installing it through the IPON connector and into the Ethernet connection port of the ENCOM Broadband radio unit. Failure to ensure a clean and dry Ethernet cable, regardless of it being fished through a conduit or not, and having it installed into ENCOM Broadband radio unit may result in degraded RF performance and can lead to full radio failure that may void the warranty of your unit. Page 4
5 4.0 Ethernet Cable Pin-outs It is recommended to use a shielded Ethernet cable with your ENCOM Broadband product. The pin-outs and function of each pin is as follows: 4.1 Ethernet Cable Termination If there is a need to re-terminate your Ethernet cable, it is important to have a properly terminated cable in order to effectively maintain power to the radio and network connectivity. The following steps outline the correct ENCOM approved procedure for terminating your Ethernet cable end Preparing your Ethernet Cable The cable jacket offers not only physical protection, but in shielded cables, it offers an RF shielding to minimize electromagnetic interference effects. It is imperative that you do not strip back any more of the cable jacket than necessary. This is typically ½ in length. Page 5
6 Step 1 Cable Stripper Using a cable stripper cut back the jacket of the Ethernet jacket exposing the twisted wire pairs inside. The pairs of wires that are inside will need to be unwound and remain un-stripped as shown below: Step 2 Lining the Colors Using the chart (see Ethernet Cable Pin-outs above), untwist the pairs of wires and line them up according to the pin-out chart order. Trim the cables so that you maintain the ½ requirement as outlined above. Step 3 Terminating Insert the lined up Ethernet wire pairs into the Ethernet (RJ45) jack making sure not to twist or misalign any of the colors in the process. The Ethernet cable should fit firmly into the jack with each of the cables firmly pushed forward all the way. Insert the cable into the crimping tool making sure that pressure points on the crimper are lined up with the two points as shown below: Page 6
7 With a proper crimp completed, you will see the gold plated electrical contact pierce not only all eight wires but the insulation of them to complete the contact with the copper conductor. The rear of the RJ45 jack is being held in place with the strain relief action of the plastic gripper keeping the connectors intact. 4.2 Weatherproofing ENCOM Broadband Radios In order to ensure continued and uninterrupted wireless connectivity of your ENCOM Integrated Broadband Radio network, the connection on your integrated units need to be verified as well as each external connection point properly weatherproofed Broadband 4.9GHz/5.8 GHz/BB58N2 and ENERGY IPON Connector The IPON Connector screws into the Ethernet port of the ENCOM Integrated Broadband Radio to offer structural security and a weatherproof connection point for the Ethernet cable. Locate the IPON connector: The IPON connector consists of the following four pieces as shown in the picture below. All four components are necessary in order to form a weatherproof seal for the Ethernet cable. If you do not have all of these pieces please contact your local ENCOM dealer to obtain a replacement IPON connector. Screw Cap and Main Body Inner Seal Strain Relief Page 7 Rubber Washer
8 In order to properly weatherproof the Ethernet connection, first slide the Ethernet cable through the Screw Cap/Strain Relief housing. Next, locate the split in the Inner Seal, and wrap it around the Ethernet cable. Next, slide the Main Body onto the Ethernet cable. Next, push the Inner Seal into the bottom of the Main Body. Next, connect the Ethernet cable to the Ethernet port on the bottom of the ENCOM Broadband radio. Next, screw the Main Body onto the Ethernet port on the Bottom of the ENCOM Broadband radio. Page 8
9 Next, screw the Screw Cap/Strain Relief onto the Main Body of the IPON, and tighten. 5.0 Mounting Your ENCOM Broadband Radio Always mount your ENCOM radio at the HIGHEST AVAILABLE POINT to achieve optimal line of site (LOS) and to help insure good signal strength Choose a location with no obstacles between sites to maximize the connection quality of the radio link Make sure each INTEGRATED ENCOM radio is mounted so the Ethernet port is pointing downward Always seal any external connection points on the Integrated Broadband Radio with heat shrink tubing Page 9
10 6.0 Approved Installation of ENCOM Integrated Radios The following outlines the correct installation for the ENCOM BROADBAND INTEGRATED Radios. An installation that correctly follows all of the ENCOM guidelines for installation will be covered for the duration of the warranty of the Broadband Radio. Page 10
11 7.0 Approved Installation of ENCOM Non-Integrated Radios Always mount your ENCOM radio at the HIGHEST AVAILABLE POINT to achieve optimal line of site (LOS) and to help improve signal strength Choose a location with no obstacles between sites to maximize the connection quality of the radio link Make sure each NON-INTEGRATED ANTENNA is mounted with the same polarization; vertical or horizontal Always seal any external connection points on the Integrated Broadband Radio with heat shrink tubing The following outlines the correct installation for the ENCOM Non-Integrated Broadband Radio. 7.1 Non-Integrated ENCOM Radio Polarization For each link in the radio network the ENCOM Non-Integrated Broadband Radio is to have the same polarization throughout; Vertical or Horizontal. Do not mix polarizations for one radio link Page 11
12 7.2 Weatherproofing Non-Integrated Broadband Radio In order to ensure continued and uninterrupted wireless connectivity of your ENCOM Non-Integrated Broadband Radio network, the connection on your non-integrated units need to be verified as well as having each external connection point properly waterproofed. Page 12
13 8.0 Sealing the Antenna Connection Points Each antenna connection point on the non-integrated radio must be properly sealed with the heat shrink tubing. The heat shrink tubing offers protection against the weather elements while maintaining a dry internal connection. Follow the steps below: Page 13
14 9.0 ENCOM Approved Seal Using Heat Shrink The following picture shows an ENCOM approved sealing of an RF connection port on an ENCOM Broadband Radio using the heat shrink tubing: There are no exposed points on the RF connector, LMR cable, or on the RF connection point on the Broadband Radio. This is an ENCOM Approved seal using heat shrink tubing. Failure to follow these installation procedures may result in your warranty being void. ENCOM Wireless, based in Calgary, Canada, provides field-proven, cost-effective wireless data solutions for municipal and industrial clients, with applications in the areas of: * Intelligent Transportation Systems * Public safety communications * Municipal corporate security and IT networks * Water and waste water management * Electrical utilities * Oil and gas #7, Avenue NE Calgary, AB T2E 7J Arapaho Road Addison, TX Page 14
7878 K940. Checkpoint Antenna. Kit Instructions. Issue B
7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added
More informationProduct Manual MNX10050 / REV C MODELS:
VIBRATION ANALYSIS HARDWARE Product Manual MNX10050 / REV C MODELS: CC-AXX & JXX CC-C2X & C3X CC-V2R & V3R Field Installable Connector Kits Contents Section I Overview Introduction... 2 Description...
More informationConnecting the Radio:
Connecting the Radio: Step 1: Connect the Cat5 cable from the radio into the RJ-45 jack marked CPE on the POE injector. The POE injector is not weather proof and should be installed indoors. Step 2: Connect
More informationDOCUMENT TR2028/R3- PICO BASE STATION WITH GPS SYNC
19473 Fraser Way,Pitt Meadows, B.C. Canada V3Y 2V4 Phone (604) 460-6002 Fax (604) 460-6005 www.tranzeo.com DOCUMENT TR2028/R3- PICO BASE STATION WITH GPS SYNC HARDWARE INSTALLATION GUIDE Thank you for
More informationALTAI A8N SERIES SUPER WIFI BASE STATION INSTALLATION GUIDE. Version 1.0 Date: September, Altai Technologies Ltd. All rights reserved
ALTAI A8N SERIES SUPER WIFI BASE STATION INSTALLATION GUIDE Version 1.0 Date: September, 2013 Copyright 2007 Altai Technologies Limited ALL RIGHTS RESERVED. Altai Technologies Limited Unit 209, 2/F, East
More informationAurora,Ohio Fax:
VPI VIDEO 1275 Danner Drive PRODUCTS Tel: 330-562-2622 www.vpi.us INCORPORATED Aurora,Ohio 44202 Fax: 330-562-1999 CRIMP-RJ45-SF 8 Contact Modular Crimp Tool For RJ45 Superflat Modular Plugs Introduction
More informationProduct Manual MNX10050 / REV B MODELS:
VIBRATION ANALYSIS HARDWARE Product Manual MNX10050 / REV B MODELS: CC-AXX & JXX CC-C2X & C3X Field Installable Connector Kits Contents Section I Overview Introduction... 2 Description... 2 Section II
More informationWEB I/O. Wireless On/Off Control USER MANUAL
Wireless On/Off Control Technical Support: Email: support@encomwireless.com Toll Free: 1 800 617 3487 Worldwide: (403) 230 1122 Fax: (403) 276 9575 Web: www.encomwireless.com Warnings and Precautions Warnings
More informationBL-ER-P Ethernet Radio Unit for Pedestal Installation Guide
Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem
More informationProduct Specification provides test results and product performance requirements.
This specification covers the requirements for application of Category 6 Modular Plug Connectors. These requirements are applicable to hand or automatic machine terminating tools. Cables approved for use
More informationLumewave and LumInsight IoT. Gateway and Base Station Installation Guide
Lumewave and LumInsight IoT Gateway and Base Station Installation Guide P/N 055-0121-01B 8/9/2018 Contents Installation Planning 3 Gateway Types 3 Gateways 4 Base Stations 4 Antenna Specification 4 Antenna
More informationBel Stewart Connector
Page 1 of 8 PLUG ASSEMBLY INSTRUCTIONS FOR Cable with INDIVIDUALLY SHIELDED PAIRS (PIMF or SFTP) T568B Wiring Pattern For Cable with Overall Foil Shield (FTP), See Page 9 1 2 Cut cable to length. If you
More informationPAC-12 Kit Contents. Tools Needed Soldering iron Phillips screwdriver Wire stripper Wrenches, 7/16 and 1/2 Terminal crimp tool Pliers Solder
PAC-2 Kit Contents Part Quantity Screws: 8/32 x 3/8 Screws: 8-32 x 5/6 Screw: 8-32 x /4 #8 internal tooth washers #8 solder lug ring terminals Bolt: Aluminum, /4-20 x.5 /4 internal tooth washer Nut: Aluminum
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationGE Monogram. Installation. Instructions. 36" Vent Hood. Model ZV750. Call anywhere in the US and Canada -
at :: rangehoods. com GE Monogram Instructions Model ZV750 GE Monogram at:: rangehoods. com is a division of CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT:
More informationGORE Aerospace Ethernet Cables
Termination Instructions The following procedures are based on Gore s best practices for terminating GORE Aerospace with the Carlisle Octax Connector System for both socket and plug versions. These procedures
More informationSignal Mirror Installation Instructions Toyota Tacoma
Signal Mirror Installation Instructions 2005-2015 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0115-0 Rev. A4 (3/11/15), BTV 2005 Muth Mirror Systems, LLC Page 3 of 12PplPage 3 of 12
More informationMIL-STD B (SH) UPDATE
MIL-STD-2042-5B (SH) UPDATE Method 5A1 Insert Equipment and materials (to be added to table 5A1-I) Pliers 3.2.2.2 Cable and fiber preparation for Fiber Systems International backshells. Step 1: Ensure
More informationUSER MANUAL. MODEL 2017A RS-232 to 20ma Current Loop Converter. SALES OFFICE (301) TECHNICAL SUPPORT (301)
USER MANUAL MODEL 2017A RS-232 to 20ma Current Loop Converter Part# 07M2017A-A Doc# 073021UA Revised 10/15/93 SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www.patton.com 1.0 WARRANTY
More informationSingle Band 125mm Profile Panel Antennas Installation and Operation Instructions Including APM-F-084-S4 & APM-T-085-S4 Mounting Kits
General Single Band 125mm Profile Panel Antennas Installation and Operation Instructions Including APM-F-084-S4 & APM-T-085-S4 Mounting Kits This instruction sheet contains all necessary information required
More informationCisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna (AIR-ANT2588P3M-N)
Cisco Aironet.4-GHz/5-GHz 8-dBi Directional Antenna (AIR-ANT588P3M-N) This document outlines the specifications for the Cisco Aironet AIR-ANT588P3M-N.4/5-GHz 8-dBi 3-Port Directional Antenna with N-connectors
More informationGMR 420/620/1220 xhd2 Series Installation Instructions
GMR 420/620/1220 xhd2 Series Installation Instructions To obtain the best performance and to avoid damage to your boat, install the device according to these instructions. Read all installation instructions
More informationPowersafe Termination Guide
Powersafe Termination Guide Contents Index 1. Introduction 2. Overview 3. Termination Methods 3.1 Set screw termination 3.2. Recommended Assembly Procedure for Panel Mounted Connectors 3.3. Crimp Termination
More informationZIP CLOUD SUSPENDED INSTALLATION MANUAL
ZIP CLOUD SUSPENDED INSTALLATION MANUAL www.delviro.com info@delviro.com 1.877.502.3434 SAFETY NOTE: Follow the Electrical Codes of the Country where this fixture will be installed. For Canada follow the
More informationGMR 420/620/1220/2520 XHD2 SERIES INSTALLATION INSTRUCTIONS
GMR 420/620/1220/2520 XHD2 SERIES INSTALLATION INSTRUCTIONS Important Safety Information WARNING See the Important Safety and Product Information guide in the product box for product warnings and other
More informationINSTALLATION AND OPERATION MANUAL. Multiple-Radio Interface Module 41021G P-26 (11-12) 2012 David Clark Company Incorporated
INSTALLATI AND OPERATI MANUAL Multiple-Radio Interface Module 41021G-01 19537P-26 (11-12) 2012 David Clark Company Incorporated Table of Contents Cautions and Warnings... 1 Parts/Tools List... 2 Supplied
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More information3 Shielded Compact Ribbon (SCR) Wiremount Plug, XX, and Shell Kit, F200-XXX
3 Shielded Compact Ribbon (SCR) Wiremount Plug, 36110-3000XX, and Shell Kit, 36310-F200-XXX Instructions June 2007 78-9100-4282-5 General This instruction manual explains the method of assembling the 3M
More informationCopyright Black Box Corporation. All rights reserved.
Copyright 2004. Black Box Corporation. All rights reserved. 1000 Park Drive Lawrence, PA 15055-1018 724-746-5500 Fax 724-746-0746 JULY 2004 LW6200A LW6201A Pure Networking 2.4-GHz Antennas CUSTOMER SUPPORT
More informationEP-60 END OF CAR JUNCTION BOX KIT and ASSEMBLY AND INSTALLATION INSTRUCTIONS
EP-60 END OF CAR JUNCTION BOX KIT 786282 and 786438 ASSEMBLY AND INSTALLATION INSTRUCTIONS Figure 1 EP-60 End of Car Junction Box Kit Item No. Qty. Description P/N Kit No. 786282 Kit No. 786438 1 2 Screw,
More informationYagi and Omni Antennas Installation Manual
Yagi and Omni Antennas Installation Manual 25500445 Rev. A0 0218 Printed in U.S.A. Copyright 2018 Federal Signal Corporation Limited Warranty This product is subject to and covered by a limited warranty,
More informationFirestar v Series air cooled laser & Flyer 3D System Quick Start Guide
Important Note: See the Flyer 3D Marking Head and Firestar v Series Laser Operators Manual for complete installation details and instructions. A PDF version is available Online at: http://www.synrad.com/manuals/manuals_laser.htm.
More informationTNC SERIES General... 4 Interface... 5 Characteristics...6-7
CONTENTS PAGE TNC SERIES General... 4 Interface... 5 Characteristics...6-7 TNC 50 Ω SERIES Plugs...8-9 Jacks...0- Jacks and receptacles... Receptacles...-4 Adapters... 5 Caps... 6 TNC 75 Ω SERIES Plugs...
More informationQuick Start Guide. Version: 1.0 F/W: V1.2.0_RC1b. Date: December 11, 2017
VigorAP 920R Series Ruggedized Outdoor AP with Extreme 802.11ac Power Warranty Quick Start Guide Version: 1.0 F/W: V1.2.0_RC1b Date: December 11, 2017 We warrant to the original end user (purchaser) that
More informationC99-20LL System Cable P/N 40935G-06 INSTALLATION SHEET
C99-20LL System Cable P/N 40935G-06 INSTALLATION SHEET The C99-20LL Interface cable connects a Universal Gateway Wireless System with the David Clark Series 9500 Marine Intercom System, and allows the
More informationShetland Stalls Installation Instructions
Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front
More informationPacific Antenna RF Probe assembly
Pacific Antenna RF Probe assembly Parts In the Kit: 1 1/2 x 3 Blue PEX tube 2 5/8 O.D. vinyl caps 2 3/32 dia x 2 brass tube sections 2 Pogo spring contacts 1 4-40 x 7/16 pan head screw 1 4-40 x 1/4 pan
More informationHughes 9300 Series Mobile Satellite Terminal
Hughes 9300 Series Mobile Satellite Terminal Installation Guide 1038494-0001 Revision E Copyright 2011 Hughes Network Systems, LLC All rights reserved. This publication and its contents are proprietary
More informationHughes 9450 Mobile Satellite Terminal. Installation Guide
Hughes 9450 Mobile Satellite Terminal Installation Guide 3004129 Revision A September 15, 2010 Copyright 2010 Hughes Network Systems, LLC All rights reserved. This publication and its contents are proprietary
More informationLJ element beam for 10 or 12 meters INSTRUCTION MANUAL. CAUTION: Read All Instructions Before Operating Equipment
LJ-113 3 element beam for 10 or 1 meters INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment 308 Industrial Park Road Starkville, MS 39759 USA Tel: 66-33-9538 Fax: 66-33-6551 VERSION
More informationMA5B 20 / 17 / 15 / 12 / 10 Meter Beam Antenna
ASSEMBLY AND INSTALLATION INSTRUCTIONS NE 20 / 17 / 15 / 12 / 10 Meter Beam Antenna 951485_GF_AB WARNING THIS ANTENNA IS AN ELECTRICAL CONDUCTOR. CONTACT WITH POWER LINES CAN RESULT IN DEATH, OR SERIOUS
More informationWater Level Meter: Op Instructions
Equipment Check 1. Turn sensitivity switch fully clockwise. Notes: 1. Clockwise rotation of sensitivity swsitch turns meter on and increases sensitivity. 2. Always set switch to highest sensitivity position,
More informationES3640e MFP Technician s Installation Guide
Technician s Installation Guide Configuration A with High Capacity Feeder HCF.jpg Configuration B with Second Tray and Cabinet cab.jpg With optional Finisher: ES3640e MFP 01_Finis her.jpg 1 Warning Icon.jpg
More informationMiniature Waterproof Shielded Connectors
Miniature Waterproof Shielded Connectors LF Series Mated dimensions 8.9 mm max. ( pos.). Ø Receptacle Plug Short turn bayonet lock Features. Ease of shielded termination and connector assembly All components
More informationCisco Aironet 5-dBi Diversity Omnidirectional Antenna (AIR-ANT2452V-R)
Cisco Aironet 5-dBi Diversity Omnidirectional Antenna (AIR-ANT2452V-R) This document outlines the specifications for the Cisco Aironet 5-dBi Diversity Omnidirectional Antenna (AIR-ANT2452V-R) and provides
More informationUniversal End of Period (EOP) Segment Installation Manual
Universal End of Period (EOP) Segment Installation Manual Size: 1 Segments are.85 H x 1 L (.0 x.3 meters) Size: 16 Segments are.85 H x 16 L (.0 x.4 meters) 1 Segment Amperage -.09 Amps @1VDC 16 Segment
More informationGMR FANTOM 50/120 SERIES INSTALLATION INSTRUCTIONS
GMR FANTOM 50/120 SERIES INSTALLATION INSTRUCTIONS Important Safety Information WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important
More informationOn-Line Cardio Theater Wireless Digital Transmitter Installation and Instruction Manual
On-Line Cardio Theater Wireless Digital Transmitter Installation and Instruction Manual Full installation instructions accompany your Cardio Theater equipment order. This On-Line version of our Installation/Instruction
More informationHow To Install Weather Pack Bulkhead Wire Connectors
How To Install Weather Pack Bulkhead Wire Connectors Weather Pack wire connectors are the premium line of environmentally sealed connectors from Delphi/Packard. The bulkhead series creates a secure and
More informationBrewsBySmith.com STC DIY Kit
BrewsBySmith.com STC-1000 + DIY Kit Contact Information: Greg Smith www.brewsbysmith.com greg@boostbysmith.com I. Hardware Included: STC-1000 flashed with latest software (v1.06 currently) (if purchased)
More informationMiniature Waterproof Shielded Connectors
All non-rohs products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales
More informationVHF 100/200 Series Radio Installation Instructions
These installation instructions are for the following VHF radios and handsets: North American Models VHF 100 VHF 200 GHS 10 International Models VHF 100i VHF 200i GHS 10i Compare the contents of this package
More informationDocument # Rev. C October, GEMINI EXPRESS MULTIPLEXER User s Guide
Document # 400-2601-01 Rev. C October, 2002 GEMINI EXPRESS MULTIPLEXER User s Guide TABLE OF CONTENTS SAFETY 3 Federal Communications Commission (FCC) Statement 3 Classification of LED Transmitter Device
More informationImportant Safety Information
OWNER'S MANUAL Important Safety Information 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only
More informationCisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R) This document outlines the specifications for the Cisco Aironet 2.4-GHz/5-GHz Dual-Band MIMO Wall-Mounted Omnidirectional
More informationSetting Standards Connectors M 16
Setting Standards Connectors M 16 inclusive 15 Product Overview 16 Housings page 18 Inserts page 22 Accessories page 29 Technical Data M 16 Control Signal Connectors Mechanical Data Housing Materials and
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS R , 12, 15, 17, 20, 30, 40 Meters (5/99) COMMUNICATIONS ANTENNAS
ASSEMBLY AND INSTALLATION INSTRUCTIONS R7000 10, 12, 15, 17, 20, 30, 40 Meters COMMUNICATIONS ANTENNAS 951465 (5/99) WARNING THIS ANTENNA IS AN ELECTRICAL CONDUCTOR. CONTACT WITH POWER LINES CAN RESULT
More informationLIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Ultra Digital / High Definition Television Antennas
LIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Ultra Digital / High Definition Television Antennas Assembly Instructions 1 MaxRange Ultra Antenna These instructions will lead
More informationS6 User s Manual USER S MANUAL ver. 1.0
S6 User s Manual SKEETER - 1U LOW PROFILE SOLUTION Table of Contents Tabletop Configuration 2 Tabletop Configuration Accessories 4 Slide Configuration 5 slide configuration accessories 7 rack Mount configuration
More informationScreenLogic Wireless Connection Kit. Installation Guide. pool/spa control system
pool/spa control system ScreenLogic Wireless Connection Kit Installation Guide P/N 520663 - Rev A 8 Technical Support Contact Technical Support at: Sanford, North Carolina (8 A.M. to 5 P.M.) Phone: (800)
More informationInstallation & Operating Manual. iwap202
Installation & Operating Manual iwap202 This page is intentionally left blank. Document Number 409345 (based on 407655) (See Last Page for Revision Details) For warranty information, refer to Terms and
More informationMC CHANGER CABINET INSTALLATION INSTRUCTIONS
8M00356 REV. 10 www.standardchange.com 1-800-968-6955 Technical Phone Support is from 8:00AM to 7:30PM E.S.T., Monday-Friday Walk-in Service is from 8:00AM to 4:30PM E.S.T., Monday-Friday Parts Department
More informationSELECTIVE CALL INTERCOM SYSTEM MODEL: IM-5000 MASTER STATION
INSTALLATION INSTRUCTIONS SELECTIVE CALL INTERCOM SYSTEM MODEL: IM-5000 MASTER STATION This booklet contains information for wiring and installing the master station. All system wiring and remote station
More informationSignal Mirror Installation Instructions Honda Odyssey
Signal Mirror Installation Instructions 2005-2009 Honda Odyssey THE safety accessory of the 21st Century. P/N 210-0122-0 Rev. A4 (6/9/09), BTV 2006 Muth Company, LLC PROFESSIONAL INSTALLATION RECOMMENDED
More informationSchluter -DITRA-HEAT Repair procedure for the DHE-HK Heating Cable
Schluter -DITRA-HEAT Repair procedure for the DHE-HK Heating Cable 555758 03/2018 2018 Schluter Systems L.P. DITRA and HEAT E are registered trademarks of Schluter Systems CONTENTS 3 List of tools required
More informationJeep Cherokee 4-Door XJ Set Part # Rev
Jeep Cherokee 4-Door XJ Set Part # 10911 Rev-14 04-05-10 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided.
More informationInstallation Instructions
Installation Instructions 30 Built-In Wall Oven with Microwave JTP86, JT965 If you have questions, call 1.800.GE.CARES or visit our website at: ge.com Before You Begin Read these instructions carefully
More informationPow-R-Feed Systems Service Manual
Pow-R-Feed Systems Service Manual Important Safety Instructions Please read this manual carefully and follow its instructions. Improper use or failure to follow these instructions could result in serious
More informationLEGENDS RETRACTABLE DOOR SCREENS
LEGENDS RETRACTABLE DOOR SCREENS MAGNETIC LATCHING DESIGN SYSTEM 42 I N S T A L L A T I O N I N S T R U C T I O N S 1 MOUNTING OPTIONS Recess : Mount the Screen Cassette using Recess Mounting Clips Recess
More informationNOV 16 Rev L
Terminating Modules 856196-[ ] for Use with Modular Plug Dual Terminators 1320840-[ ] Instruction Sheet 408-9743 17 NOV 16 Rev L Modular Plug Dual Terminator Automatic Circuit Tester (Terminators 1320840-1
More informationTechnician License. Course
Technician License Course Technician License Course Chapter 4 Lesson Plan Module - 10 Practical Antennas The Dipole Most basic antenna The Dipole Most basic antenna The Dipole Total length is ½ wavelength
More informationHughes 9450 Mobile Satellite Terminal Series. Installation Guide
Hughes 9450 Mobile Satellite Terminal Series Installation Guide Document No. 3004129-0001 Revision E 17 November 2017 Copyright 2013, 2017 Hughes Network Systems, LLC All rights reserved. This publication
More informationmicro DOUBLE TEN SWITCH
micro DOUBLE TEN SWITCH microham fax: +421 2 4594 5100 e-mail: support@microham.com homepage: www.microham.com 5 December, 2011 1 TABLE OF CONTENTS CHAPTER PAGE 1. IMPORTANT WARNINGS... 3 2. DESCRIPTION...
More informationBi-Color Signal Mirror Installation Instructions
Bi-Color Signal Mirror Installation Instructions 2005-2009 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0141-0 Rev. A2 (3/30/09), BTV 2007 Muth Mirror Systems, LLC Page 3 of 13PplPage
More information8-Position Cat6 Shielded Slim-Line Modular Plug
Issue 1, April 2016 8-Position Cat6 Shielded Slim-Line Modular Plug 1. Introduction This specification covers the requirements for application of Category 6 shielded slim-line modular plug connectors.
More informationKit Kit. GeoSteer GS-900 Radio Kit. GS-900 Radio Kit Installation Instructions Rev A
200-0652-01 Kit 200-0652-02 Kit GeoSteer GS-900 Radio Kit Item Component Part Number Qty Notes 1. Assembly, Radio GS-900 200-0642-01 (North America) 200-0642-02 (Australia) 1 Radio assembly in kit is region
More informationInstallation Job Aid (English) for Avaya WLAN 8100 series- WLAN AP 8120 with External Antenna
Release 3.0 NN47251-311 Issue 02.01 June 2014 Installation Job Aid (English) for Avaya WLAN 8100 series- WLAN AP 8120 with External Antenna How to get help To access the complete range of services and
More informationR/L, AND LXE TYPE CABLE
OFS Fitel Figure 1. FOR CROSSPLY, R/L, AND LXE TYPE CABLE 636-299-110-05 Comcode: 847 815 297 12A1 Cable Clamp Issue 2 March 2002 2002 OFS Fitel All Rights Reserved Printed in U.S.A. Page 1 of 6 12A1 CABLE
More informationPCS. Patient Security Service Console. Installation Instructions.
www.hsiheadwals.com PCS Patient Security Service Console Installation Instructions Tel: 925.427.7800 Fax: 925.427.0800 support@hsiheadwalls.com Hospital Systems Inc. 750 Garcia Avenue Pittsburg CA 94565
More informationTRANSFORMER HD-HAMPTON HAMPTONBAY.COM
Item #1001 510 115 Model DIY-600PS USE AND CARE GUIDE TRANSFORMER Questions, problems, missing parts? Before returning to the store, call HamptonBay Customer Service 8 a.m. - 7 p.m., EST, Monday Friday,
More informationInstallation Instructions for Cirrus Suspension Downlight with Power - End Feed. Section One: 4" Flush Canopy Version
Doc # 0-CSP-E_0 W. Fullerton Chicago, IL 606 Ph:.0. Fax:..6 www.pureedgelighting.com info@pureedgelighting.com 06 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Suspension
More informationInstallation Instructions
Installation Instructions Optima LED 8 Double-Sided StretchLite Perimeter Lit Graphic Display Line Voltage Connector Optima LED DS5 (Double-sided StretchLite Graphic Display) with Graphics Corner Bracket
More informationMPR kHz Reader
MPR-5005 Page 1 Doc# 041326 MPR-5005 125kHz Reader Installation & Operation Manual - 041326 MPR-5005 Page 2 Doc# 041326 COPYRIGHT ACKNOWLEDGEMENTS The contents of this document are the property of Applied
More informationInstruction Manual for 98cm Elliptical Ka Antenna
Instruction Manual for 98cm Elliptical Ka Antenna 98cm WB Issue 03 Caution This instruction leaflet will assist you in the correct installation of the product. Read it prior to starting any installation
More informationAmphenol RF Interconnects BNC 31 Series Bayonet Lock RF Connector System
BNC 31 Series Bayonet Lock RF Connector System Materials Body/Finish /Nickel Centre MALE Centre FEMALE Phosphor Bronze Centre Finish Gold 30µ Insulator Delron/PBT Gasket Silicone Rubber Crimp s Annealed
More informationRibcage Installation. Part 2 - Assembly. Back-Bone V1.06
Ribcage Installation Part 2 - Assembly Back-Bone V1.06 Contents Section 1 Before You Get Started... 2 Included With Your Kit:... 2 Figure: A... 3 CAUTION!... 4 Note:... 4 Tools Required... 5 Section 2:
More informationUser Manual. ProRF Encoder Transmitter & Receiver
User Manual ProRF Encoder Transmitter & Receiver WARRANTY Accurate Technology, Inc. warrants the ProScale Systems against defective parts and workmanship for 1 year commencing from the date of original
More informationINSTRUCTION MANUAL HF AUTOMATIC ANTENNA TUNER AT-141
INSTRUCTION MANUAL HF AUTOMATIC ANTENNA TUNER AT-141 FOREWORD Thank you for purchasing the AT-141 HF AUTO- MATIC ANTENNA TUNER. The AT-141 is designed, primarily for use with Icom HF transceivers. Refer
More informationReasons for reissue are in Section 6, REVISION SUMMARY.
Figure 1 This instruction sheet covers the application of OPTIMATE FSMA Fiber Optic Connector Types 905 and 906 for data and telecommunications applications. Base part numbers which apply to each type
More informationM1 Series. Humidity - Temperature Transmitter INSTRUCTION MANUAL
M1 Series Humidity - Temperature Transmitter INSTRUCTION MANUAL 20031110 -2- CONTENTS Overview... 3 Operation... 4 Power supply... 4 Operating range and limits... 4 Temperature compensation of the humidity
More informationDirective Systems & Engineering 2702 Rodgers Terrace Haymarket, VA
Directive Systems & Engineering 2702 Rodgers Terrace Haymarket, VA 20169 1628 www.directivesystems.com 703 754 3876 K1JX DESIGNED 6 ELEMENT 50 MHZ YAGI, DSEJX6 50 INTRODUCTION The Directive Systems DSEJX6-50
More informationSection 5 BATTERY REPLACEMENT
u Section 5 BATTERY REPLACEMENT j i 5.1 General The internal battery is used for preserving the clock and programming memory in the models 5000 and 7000. I i The procedure for each is given separately.
More informationELECTRO-MECH SCOREBOARD CO. SL-230 / 330 RF MODEM INSTALLATION MANUAL
ELECTRO-MECH SCOREBOARD CO. SL-230 / 330 RF MODEM INSTALLATION MANUAL Thank you for choosing an Electro-Mech Scoreboard for your athletic complex. We are confident that this product will give many years
More informationRoline L1 Series. Humidity - Temperature Transmitters INSTRUCTION MANUAL
Roline L1 Series Humidity - Temperature Transmitters INSTRUCTION MANUAL 20030314 CONTENTS Overview... 3 Operation... 5 Power supply... 5 Operating range and limits... 5 Temperature compensation of the
More informationkwiqmate Connectors Product Catalog Johnson
Product Catalog Johnson Emerson Connectivity Solutions, provider of kwiqmate branded Johnson product line of QMA connectors features a push-on style interface. Traditionally SMA plugs need to be configured
More informationMobile Gain Antennas MHz Models RRA-4935/RRA-4936
890-960 MHz Models RRA-4935/RRA-4936 Installation See Table 1 for recommended antenna location for various vehicles. The installation procedure which follows is for a typical passenger car. The procedure
More informationQUANTUM Qflash T2 / X2 OPERATING INSTRUCTIONS
QUANTUM Qflash T2 / X2 OPERATING INSTRUCTIONS 1.0 DESIGNATIONS T2 AND X2 1. Removable Reflector, two positions Normal and Wide angle. 2. Flash-tube 2A. Modeling Lamp (for Model X2 only) 3. Bounce Head,
More informationCaution: Installation and Operation Instructions. Locking Mechanism (if supplied) Set Screws Backed Out. Mounting Orientation
Genie Probe Regulator (GPR)/ Genie Probe (GP2)/ Genie Probe for Composite Sampler (CSA)/ And (Model H) Installation and Operation Instructions Caution: Not designed for external fire. Prior to use in a
More informationRisk Assessment & Safe Working Practice
RA Ref Number: 46 Revision: 3 Project/Job Number Reference Insert Job Number Approval Date: 30/03/2018 RA Description: Electrical Termination Pyro Next Review Date: 01/04/2019 Notes: Please refer to Safe
More informationCisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949)
Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949) Overview This document describes the 13.5-dBi Yagi mast mount antenna and provides instructions for mounting it. The antenna operates in the
More information