VHF Meteor Scattering Data Link

Size: px

Start display at page:

Download "VHF Meteor Scattering Data Link"

Regina Walsh
5 years ago
Views:

1 VHF Meteor Scattering Data Link Final Report Fall Semester 2009 Prepared to partially fulfill the requirements for ECE401 Department of Electrical and Computer Engineering Colorado State University Fort Collins, CO By: Jassim Makki Naif Alhujilan Rashid Al-Mohannadi Report Approved: Project Advisor Senior Design Coordinator -1-

2 Abstract: Meteors could be used to establish point to point data link. Meteors hit the atmospheric layer everyday and provide an opportunity to scatter waves and thus establish a communication link. The task is to establish this link between two points 67 miles apart at 50MHz. 67 miles is considered to be a short distance for meteor scattering and this project testify if it is possible. However, the link must support at least 20 signal-to-noise-ratio. This project started with installing a test bench that repeatedly transmits waves at 50 MHz and the task is to find if there is any meteors enhancement. This includes using an antenna that has low angle radiation and high angle radiation that would permit meteor scattering and tropospheric scattering. Then, the received signal must be analyzed to find out if there is meteor scattering. If not, the system must be analyzed to find out what is missing to establish this link. However, the received signal was low and no varying which means that there is no meteor scattering. This is due to two reasons. The first reason is that the distance between the two points is limiting the probability of finding meteors that could be used for scattering. This is similar to shooting thru a ring that is located far away. However, it is still possible to do it if more directed antennas with higher gain is used. On the other hand, this experiment showed us that there is a high noise at 50MHz which resulted in a low SNR=1.5. This noise is mainly because of man-made noise. -2-

3 TABLE OF CONTENTS Title Abstract Table of Contents... 3 List of Figures and Tables I. Introduction II. Approach.. 7 III. Transmission station 8 IV. Receiver station 12 V. Radio Propagation study. 13 VI. AFSK Modems 15 VII. Results.. 15 VIII. Options 19 - Antenna.. 21 IX. Current status 22 X. Next Semester 22 XI. Conclusion 23 References.. 24 Appendix A - Budget 25 Appendix B - Acknowledgment 26-3-

4 LIST OF FIGURES Figure 1: Communication Channels for VHF Meteor Scatter project 7 Figure 2: Morse code diagram. 9 Figure 3: Block diagram. 10 Figure 4: Flow Chart. 11 Figure 5: Noise vs. Frequency 14 Figure 6: Simulation Results 16 Figure 7: power Pattern. 17 Figure 8: MS & TS 18 Figure 9: corner Antenna. 21 Figure 10: Power pattern of Corner Antenna. 21 Figure 11: Modems & noise injection.. 22 LIST OF TABLES Table 1: Budget 25-4-

5 I. Introduction: In this project we will explore the possibility of building a point to point link with meteor scatter that would help to develop a communication system that operates at a very high frequency of fifty mega hertz (50 MHz). This frequency would help study the different propagation modes, like meteor scattering to improve this wireless communication system. This physical system would help us as engineers, rather than being students to experience real life obstacles that field engineers encounter. Furthermore, thanks to our super visor we were able to get sense of how to deal with real life design approaches and how making mistakes is more desirable to learn from them. Meteor scattering is a radio propagation mode that utilizes the ionized trails of meteors where a short path of communication can be establish between two communication stations that can ranges up to 2250 kilo meters or about 1400 miles. When meteors enter the upper atmosphere they burn up creating a trail of ionized particles that can keep on for several seconds, those particles in the ionized trails can be very dense that can be used to reflect radio waves. The intensity of the ionized trails determines the frequencies that can be reflected which sometimes ranges between 20 MHz and 500 MHz.when it comes to how much of a distance a communication is established, even though the trails exists only for fractions of a second to few several seconds which indicate a small window of communication, there are some factors that need to be considered ; which includes the altitudes at where the ionization is shaped, location of the falling meteor over the earth s surface, the meteor s angle of entry to the upper -5-

6 atmosphere and the location of the communication stations where the channel is desired to be established. One of the applications of Meteor Scatter communication is an automated system called SNOTEL of snowpack where it related to climate sensors. SNOTEl is the acronym for SNOwpack TELemetry which is defined as network of computers, people, communication devises, microprocessors and sensors to collect hydro meteorological data. SNOTEL was the motivation for using meteor scatter in this project. This data that SNOTEL collects can include the measurements of snow and water content, temperature and accumulated snow or rain. This application of meteor scattering is the one of the motivations to build such a communication system. After introducing the project and some back ground of Meteor scatter, this report will explain the different approaches of the main goal which is building the link between two communication stations with our physical system along with our current results. Figure 1 shows a friendly painted picture of the project; where it can be shown the communication channels using meteor scattering. -6-

7 Figure 1: Communication Channels for VHF Meteor Scatter project. II. Approach: In this project we had some outlined planning on how we can build a system that can act as our SNOTEL; the approaches can be ordered as follows with a brief enlightenment for each approach; First, transmitting a signal from a remote signal to a local place in Fort Collins, this step includes the following procedures to achieve this objective. 1- Build a test bench that includes the automated station at the remote site where the transmission takes place. 2- Build a receiver satiation in Fort Collins. -7-

8 From the previous approach, it can be concluded that in this approach we are building the point to point communication stations where the desired channel of communication using Meteor Scatter will take place. Then, after building our radio stations; data about the transmitted signal from the remote station is going to be collected and analyzed to monitor any enhancement caused by meteor scattering. This approach can be titled as Radio propagation study. After that, we will be building a mathematical model that would help analysis and make use of our results of the collected data, mentioned previously. Finally, we are going to build modems that can communicate using the channel we aimed to establish. This was a rough sketch of what the report is going to be talking about. The following is going to be a more detailed description of how those approaches were made along with their results, what problems that each step had and new decisions that were made beside the ones that were mentioned here. III. Transmission station: To start with, we had to build a transmission station located at John s cabin NW of Fort Collins. The transmission will be controlled by a micro controller chip that transmits known signal coded into Morse code. Morse code is a type of character encoding that transmits telegraphic information using rhythm. Morse code uses a standardized sequence of short and long elements to represent the letters, numerals, punctuation and special characters of a given -8-

9 message. The short and long elements can be formed by sounds, marks, or pulses, in on off keying and are commonly known as "dots" and "dashes". The speed of Morse code is measured in words per minute (WPM) or characters per minute. In our project, the dots and dashes are transmitted by on-off keying controlled by the micro controller and have a speed of about 10 WPM. Figure 2: Morse code diagram. To better understand the transmission station, we shall start with this block diagram. -9-

10 Push-to-talk Switch: To switch between receive and transmit mode PTT Remote: to switch between receive and transmit mode Antenna Amplifier Key Switch 12 V MC DC/DC: reduce the 24 V to 12 V (charge up the battery) Switch Divider: reduce the 12 V to a measurable voltage for The mc, if the battery charge is low the mc will turn Off the system till the battery is charged. Relay Board Switch DC/DC: reduce the 24 V to the Value (power supply for mc) 24 V Switch: to disconnect 24v battery from DC/ DC till it charges up, if needed. Disconnection is through the relay board. Figure 3: Block diagram A DC\DC divider will be used to reduce the 24v, coming from the battery bank, to about 3v to supply the micro controller chip (MC). MC chip will be monitoring the battery bank while sending the signal, if the battery bank drop below 22v, MC chip will turn the whole system off through the relay board till the battery is solar charged again. The relay board is simply two switches controlled by MC to turn off the amplifier and to disconnect the battery bank so that no power keeps being consumed. Both MC chip and key switch will be used to send the Morse coded signal by switching the transceiver on and off. This signal will be passed through amplifier and then to the antenna. -10-

11 The amplifier will be turned on and off by MC chip and has a 12v supply coming from the main battery bank. The following graph is a flow chart that summarizes the steps in transmission. Figure 4: Flow Chart -11-

12 The antenna used to transmit the signal called (Yagi antenna). It has a central element and cross elements above the central. It is an end fire antenna and has a power pattern directed to the sky at 16 degree above the ground. The system was completely installed and running by Oct. 15 th, the signal was successfully received even thou we had to operate on 150W instead of 50W. This means we will be consuming more power than what we thought, but the battery bank was able to handle that extra usage of power. IV. Receiver station: The signal is received here in Fort Collins at John s house. We will capture the signals transmitted from the beacon using a commercial, amateur radio transceiver. This radio is a very sensitive, frequency selective power meter that can be tuned to the beacon transmit frequency and can measure the received power from the beacon over time. The antenna used to capture the signal is a loop antenna, which has an omni directional pattern to receive the signal in spite of the direction it is coming from. A program written in C- sharp will get the data from the transceiver and save it in a file. These data will be collected over days and samples will be measured and saved over periods of time as desirable. Then, this data will be used to study and analyze the channel we are using. -12-

13 V. Radio Propagation study: After data was collected using the test bench, they must be analyzed to find out what type of scattering in the link. At 50 MHz, there are many propagation mechanisms including tropospheric scattering, meteor scattering and ionospheric scattering. These mechanisms have different observations which would lead the type of scattering or reflection is used. Meteor scattering is usually observed by a sudden variation on the received signal. Meteors hit the top atmospheric layer and it creates an ionized trail forming a dense area that would reflect. However, this dense area lasts for a few seconds or even a fraction of a second and this explain why enhancement in received signal lasts for a few seconds. On the other hand, meteors hit the atmospheric layer every day and the chance of getting more enhancement increases if the wave propagating travel long distance to get a better probability of reflecting from multiple meteors. An average distance of meteor scattering is about 2250km and our system has two points that are 107km apart. This is one of the challenges in this design that this short distance provides a small opportunity of observing meteors because the transmitting station will be shooting at a small window creating a small probability of hitting a meteor. Another type of scattering available at 50MHz is tropospheric scattering. In this mechanism, waves are reflected at the lowest atmospheric layer called troposphere layer. This layer extends from the earth s surface to a height of 7 miles. In this layer, there are inhomogeneous places called blobs which has a different reflection index from air causing waves to be reflected. This layer has the advantage of being available at all time which would help to test our system if it s directed towards this layer. As mentioned above, the troposphere layer exists at the lowest -13-

14 part of the atmosphere layer which requires a low angle radiation. Experiments have shown that the best results when waves are transmitted at low angle and found that for each angle above in the vertical plane costs 9-12 db. Tropospheric scattering works from 50 MHz to 10GHz which is another feature of this mechanism. Noise at 50MHz is due to different sources. It includes atmospheric noise and man-made noise. But as this plot shows man made noise is the dominant. It is at -110dBm at 50 MHz. Figure 5: Noise vs. Frequency -14-

15 VI. AFSK Modems: Once the channel is analyzed and the link is established, modems will complete this link and make it useful. Modems will be useful to control the receiver station since it can communicate with digital devices. Modems that will be used are Audio Frequency Shift Keying modems. These modems will be connected to a radio to receive or transmit information. We built these modems starting from soldering resistors and capacitors to installing IC chips. These modems come with full instructions on how to install them from the manufacturer ( ). However, it is good to build these modems to understand how they function. The modem consists of an FSK modulator and demodulator that is connected to a microcontroller which controls the whole modem and control the flow of data from the modulator to memory and then to the output using a USB connection. The software that controls the modem is obtained from the manufacturers and it is editable. However, these modems require at least SNR= 20 db to function correctly which adds another constraint to our link. VII. Results: After building the test bench, we measured the signal strength using the receiver station and recorded (-107dBm). This received power is very low and implies that there is something wrong with the link. It could be a problem with the equipments or some other source of error. To verify this recorded power, simulation software of the link would be the best start. Using free -15-

simulation software called Radio mobile, the link was simulated and the result was close to that received power. Figure 6: Simulation Results As seen from that last figure, Rx=-103dBm.

16 simulation software called Radio mobile, the link was simulated and the result was close to that received power. Figure 6: Simulation Results As seen from that last figure, Rx=-103dBm. Therefore, the recorded power is correct and this conclusion shifts our attention to figure out another possible source of error. Although the received power is low, the signal strength is still measureable and should be analyzed to work towards the project goal which is finding if there is meteor scattering communication. After monitoring the signal strength for a week, there was no enhancement and the signal strength was the same. As found in the literature about meteor and tropospheric scattering, no variation in the received signal means no meteor scattering and the dominating -16-

scattering is tropospheric scattering. However this could change if we monitor the signal for a longer time and with different set of equipments that would transmit signals at high angles.

17 scattering is tropospheric scattering. However this could change if we monitor the signal for a longer time and with different set of equipments that would transmit signals at high angles. After reaching a conclusion about the type of scattering for the signal transmitted over this short period, our attention moved to analyze the system further and find out what is behind this low received power. One possible source of error is the antennas used at either the transmitting station or the receiving station. Starting with the transmitting the antenna, a radiation pattern was obtained for a 4-element Yagi antenna that is 6 meters (the same wavelength) above ground. Figure 7: power Pattern This radiation pattern was the missing key to explain the low received power. As seen from the figure, the pattern shows no low angle radiation which is crucial for our dominant tropospheric -17-

scattering. To emphasize, tropospheric scattering needs low angle radiation, the lower the better. This analysis was used to analyze the whole system again.

18 scattering. To emphasize, tropospheric scattering needs low angle radiation, the lower the better. This analysis was used to analyze the whole system again. Figure 8: MS & TS Above is a diagram for our link, it shows that the transmitting antenna max gain is at 16.2 and the tropospheric layer, given the altitude at the transmitting station, is at lower angle. Most likely, the transmitting antenna is missing the tropospheric layer. The reason behind the nonexistence of low angle radiation is the height of the antenna which is only 6 meters and this is the wavelength of our transmitted waves. This low height compared to the wavelength causes ground reflection that prevents low angle radiation. The best solution is to raise the antenna using a tower to get low angle radiation. -18-

19 After analyzing the low signal strength, there is another problem to analyze which is the high noise measured at the receiving station. The noise as mentioned earlier was -105dBm and it is mainly due to man-made noise at 50MHz. This creates a problem and a new challenge since our design constrain is SNR=20dB. Given our noise and received power, SNR=1.5 which means that the system needs a revolution to obtain the requirement. VIII. Options: The main problem is manmade noise which badly impacts the SNR. To overcome this problem we have two options: The first option is to continue trying with meteor scattering. Since the scattering is dominated by tropospheric scattering, the angle of radiation of the antenna should be increased to point skywards so that the radiation can pass the tropospheric without reflecting. The transmitted power also should be increased to achieve higher SNR, but even with the increased power, the SNR will not be high enough to be able to use the current modems, so this mean that the modems will have to be changed as well. This option will maintain the idea of Meteor Scattering, however, it is not efficient because the needed transmitted power will not be easily generated. The second option is to move to tropospheric scattering at higher frequency. Moving to higher frequency means moving to a region where the manmade noise is much lower than the current -19-

20 noise. This criteria will help to achieve the desired SNR (20 db) and since noise is main problem, we decided to focus on the second option and build our system using the advantages of troposphere layer. Tropospheric scattering provides benefits such as: 1- Troposphere layer reflects the signal because of the differences of density and moisture at that region, so the scattering will be available all the time. 2- With troposhperic scattering, the system can use higher frequency unlike with meteor scattering and that helps in noise reduction. 3- Tropospheric scattering requires a low radiation angle, and constructing such antenna with higher gain will be easier and possible with the same equipments and power supplies we have. 4- The distance between the two ends in our system is about 62 miles and Tropospheric scattering provides a good communication channel over distances between 70 to 600 miles, while meteor scattering works better with greater distances. Because of all of these reasons, we decided to move forward in our project and build it at higher frequency (440 MHz) using tropospheric scattering. -20-

Antenna: In this new path, the signal will be transmitted using corner antenna. Corner antenna has higher gain and easier to construct because unlike Yagis almost all the dimensions are noncritical.

21 Antenna: In this new path, the signal will be transmitted using corner antenna. Corner antenna has higher gain and easier to construct because unlike Yagis almost all the dimensions are noncritical. The only critical Figure 9: corner Antenna dimension is the length of the driven element, which is simply adjusted for minimum SWR. It also has a maximum gain at an elevation angle of 2 degrees. However as you can see in the following graph, the antenna provides significant gain at all elevation angles up to 90 degrees. Figure 10: Power pattern of Corner Antenna -21-

22 IX. Current status: Currently, we are at the stage of measuring the signal to noise ratio using Radio Mobile program. We are trying to design the corner antenna in the program to simulate the path loss, the received power and SNR. We are also trying to establish a connection between two modems at base band, then, we want to inject noise to measure the Bit Error Rate. Figure 11: Modems & noise injection The noise will be added using free software that converts computers or laptops to signal generators. The summation method is what we are working on now; the noise should be injected in a way that doesn t eliminate the sent signal totally but disturb it in a controlled way so that BER at a given SNR is calculated. X. Next Semester: The goals for next semester are: 1- Complete the current status goals at the beginning of the semester ( measure BER vs. SNR) 2- Build the antenna and reallocate the beacon interface and establish the link between the two ends. -22-

23 3- Study the propagation and build mathematical model that describe the received power vs. time. 4- Establish a communication link using the modified modems so that the two ends can communicate and exchange information with each other. XI. Conclusion: This project is a communication problem that reflects real life engineering experience. We learned how to identify, solve and approach a problem and we got the opportunity to be part of this project which we would like to continue next semester to achieve the goal of it. -23-

24 REFERENCES [1] David, H.H. A new approach to long range communications. IEEE, Vehicular Communications, Aug [2] Darnell, M. Riley, N.G. Melton, D. Tropospheric scatter propagation in the low-vhf band.ieee, Antennas and Propagation, [3] Hansen, John. How to build AFSK modems. [4] Roos, Andrew. A Simple 70cm Satellite Antenna

25 Appendix A - Budget: Electrical engineering department provides 50$ for each student per semester, however, the project is funded by our supervisor John Steininger. The total money spent was 1244 $. Most of the money went into affording the beacon interface equipments. Also about 250$ was spent to buy the AFSK modems. The next table shows the total money spent in details. Part / Hard ware Expenses in $ 24V Divider 3 Key Switch 2 Relay Board 10 USB Supply 5 Misc. HW 15 Transmitter 185 Power Distribution 95 DC/DC Converter 45 Power Amplifier 270 Antenna, 4 element yagi 158 Lightening arrestor 50 Coax 92 Mast bracket 20 Connectors 30 3 modems soldering irons 60 Total: 1244 Table 1: Budget -25-

26 Appendix B - Acknowledgment: At the end, we would like to thank our supervisors for providing this opportunity and for helping us through all the semester. They have been good teachers and good team leaders. We learned about communication and lived a real life experience. -26-

A Tropospheric Scattering, Non-Line-of-Sight (NLOS) Wireless Data Communications Link

A Tropospheric Scattering, Non-Line-of-Sight (NLOS) Wireless Data Communications Link Final Report Fall Semester 2009 Prepared to partially fulfill the requirements for ECE401 Department of Electrical