Voltage Regulator TAPCON 230 basic. Quick reference guide /02

Transcription

1 Voltage Regulator TAPCON 230 basic Quick reference guide /02

2 2012 All rights reserved by Maschinenfabrik Reinhausen Copying and distribution of this document and the utilization and communication of its contents are strictly prohibited unless expressly authorized. Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a patent, utility model or ornamental design registration. The product may have been modified after this document went to press. We expressly reserve the right to make changes to the technical data, the design or the scope of delivery. Generally, the information provided and the arrangements agreed during processing of the relevant quotations and orders are binding. The original operating instructions were drawn up in German.

3 1 Introduction This technical file contains information for quickly starting up the voltage regulator. It does not pro-vide comprehensive operating instructions. This technical file is intended solely for specially trained and authorized personnel. 1.1 Manufacturer The voltage regulator is manufactured by: Maschinenfabrik Reinhausen GmbH Falkensteinstraße Regensburg, Germany Tel.: (+49) 9 41/ Fax: (+49) 9 41/ sales@reinhausen.com Further information on the product and copies of this technical file are available from this address or on our website at if required. 1.2 Completeness This technical file is only complete in conjunction with the supporting documentation. Maschinenfabrik Reinhausen

4 1.3 Supporting documents The installation and commissioning instructions, the operating instructions and the accompanying connection diagrams also apply in addition to this technical file. All documents form part of the scope of delivery. In addition, generally applicable statutory and other binding regulations in European and national legislation and the regulations for accident prevention and environmental protection in force in the country of use must be complied with. 1.4 Safekeeping This technical file and all supporting documents must be kept ready to hand and accessible for future use at all times. 4 Maschinenfabrik Reinhausen 2012

5 2 Safety This technical file does not replace the Operating Instructions for the voltage regulator. The quick reference guide contains information that will provide a rapid introduction to operating the voltage regulator. For detailed operation and safety information please read carefully through the voltage regulator operating instructions. Pay particular attention to the information in the chapter on safety in the operating instructions. Maschinenfabrik Reinhausen

6

7 3 Product description 3.1 Description of the front panel Figure 1 TAPCON 230 front panel 1 LEDs Setting options for display contrast 3 Labeling strip for LEDs 4 F1...F5: Function and menu selection keys Maschinenfabrik Reinhausen

8 5 Display 128X128 LCD module negative blue, LED background white 6 Menu selection 7 Escape 8 Accept entry 9 Switching windows within a menu level 10 Parametering interface COM 1 (RS232) 11 Automatic voltage regulation (with auto mode LED green) 12 Manual mode (with manual control LED green) 13 Remote control (with Local/Remote LED green) 14 Control for RAISE/LOWER 15 Status LED 8 Maschinenfabrik Reinhausen 2012

9 3.2 Description of the display Figure 2 Main screen 1 Status line 2 Actual value display in V/kV 3 Desired value display in V/kV 4 Control deviation 5 Time bar 6 Desired value deviation trend Maschinenfabrik Reinhausen

10 3.3 Description of key functions RAISE LOWER REMOTE MANUAL AUTO In manual mode the motor-drive unit can be operated directly using the RAISE key. In manual mode the motor-drive unit can be operated directly using the LOWER key. Activates the "Remote" operating mode. In this case, manual operation of the RAISE, LOWER, MANUAL and AUTO keys is disabled. Manual mode. For manual control of the motordrive unit and parameterization of the voltage regulator. Auto mode. Voltage is controlled automatically. Arrow keys NEXT / PREV ENTER ESC MENU In auto and manual mode, the measured value display can be set using the arrow keys. They can also be used to switch between windows in the submenus. Confirms or saves a changed parameter in the parameter menu. Pressing the ESC key transfers you to the menu level above, in other words, always back one menu level. Pressing this key displays the menu selection window. 10 Maschinenfabrik Reinhausen 2012

11 F1...F5 The function keys are menu selection keys. They are also used to scroll through the menu subgroups and input masks. Maschinenfabrik Reinhausen

12

13 4 Functions and settings This chapter provides a short summary of all the functions and possible settings of the voltage regulator. Please refer to the voltage regulator operating instructions for detailed information on each of the functions and settings. Before carrying out the parameterization, proceed as follows: 1. Deactivate the key lock if necessary. Press ESC + F5 MANUAL 2. Activate manual mode: Press. 3. Select main menu: Press MENU. The voltage regulator main menu is displayed. 4.1 Setting the language 1. MENU > F4 (Configuration) > F3 (General). <00> Language. 2. Press F1 or F5 to select the required language. 3. Press to save the setting. The required display language is set. Maschinenfabrik Reinhausen

14 4.2 NORMset The NORMset mode enables easy and user-friendly commissioning of the voltage regulator with a limited set of parameters. For switching to the NORMset mode, the following additional parameters must be set: Desired value 1 Primary voltage Secondary voltage Activating NORMset 1. MENU > F2 (Normset). <00> Normset Activation. 2. To activate Normset, press F1 or F5 to select "On". 3. Press to save the setting. The NORMset mode is activated. 14 Maschinenfabrik Reinhausen 2012

15 4.2.2 Setting desired value 1 Setting range Step size Fact. settings 49 V V 0.1 V 100 V Table 1 Setting range for desired value 1 in V Setting range Step size Fact. settings 0 kv kv 0 kv kv 0 kv kv 1 kv 0.1 kv 0.01 kv 1. MENU > F2 (Normset) >. <01> Desired Value Press F4 in order to highlight the position. 3. Press F1 to increase the desired value or F5 to decrease it. 4. Press to save the setting. Desired value 1 is set. 1 kv Table 2 Setting range for desired value 1 in kv Maschinenfabrik Reinhausen

16 4.3 Control parameters Setting desired value Setting range Step size Fact. settings 49 V V 0.1 V 100 V Table 3 Setting range for desired value in V Setting range Step size Fact. settings 0 kv kv 0 kv kv 0 kv kv 1 kv 0.1 kv 0.01 kv 1. MENU > F3 (Control Parameters) > F2 (Voltage Regulation). <00/01/02> Desired Value 1/2/ Press F4 in order to highlight the position. 3. Press F1 to increase the desired value or F5 to decrease it. 4. Press to save the setting. Desired value 1/2/3 is now set. 1 kv Table 4 Setting range for desired value 1 in kv 16 Maschinenfabrik Reinhausen 2012

17 4.3.2 Selecting desired value "Select desired value" is used to define an active desired value on the screen menu. 1. MENU > F3 (Control Parameters) > F2 (Voltage Regulation) > 3x. <03> Select Desired Value. 2. Press F1 or F5 to select an active desired value. 3. Press to save the setting. The active desired value is now selected. Maschinenfabrik Reinhausen

18 4.3.3 Setting the bandwidth Calculation of the bandwidth in accordance with the following formula: [ ±B % ] 0.6 U n-1 - U n 100 % U Nom Setting range: Setting range Step size Fact. settings 0.5 %...9 % 0.1 % 2 % Table 5 Setting range for bandwidth 1. MENU > F3 (Control Parameters) > F2 (Voltage Regulation) > 4x. <04> Bandwidth. 2. Press F4 in order to highlight the position. 3. Press F1 to increase the value or F5 to reduce it. 4. Press to save the setting. The bandwidth is set. 18 Maschinenfabrik Reinhausen 2012

19 4.3.4 Setting delay time T1 Setting range Step size Fact. settings 0 s s 1 s 40 s Table 6 Setting range for delay time T1 1. MENU > F3 (Control Parameters) > F2 (Voltage Regulation) > 5x. <05> Delay Time T1. 2. Press F4 in order to highlight the position. 3. Press F1 to increase the value or F5 to reduce it. 4. Press to save the setting. The delay time T1 is set. Maschinenfabrik Reinhausen

20 4.3.5 Setting the control response T1 (linear/integral) Linear: With "Linear Time" the regulator responds with a constant delay time which is independent of the control deviation. Integral: The delay time decreases depending on the relationship of the control deviation to the set tolerance bandwidth B, to a minimum of 1 second. 1. MENU > F3 (Control Parameters) > F2 (Voltage Regulation) > 6x. <06> Characteristics T1. 2. Press F5 to select "linear" or F1 to select "integral". 3. Press to save the setting. The control response T1 is set. 20 Maschinenfabrik Reinhausen 2012

21 4.3.6 Activating delay time T2 The delay time T2 only comes into effect when more than one tap-change operation is necessary and the first tap-change operation (end of T1) has already taken place. 1. MENU > F3 (Control Parameters) > F2 (Voltage Regulation) > 7x. <07> Activation T2. 2. Press F1 or F5 to activate T2. 3. Press to save the setting. The delay time T2 is now activated. Maschinenfabrik Reinhausen

22 4.3.7 Setting delay time T2 In general, the delay time T2 should be greater than the pulse duration and the maximum operating time of the motor-drive unit. This applies to continuous settings in particular. Setting range Step size Fact. settings 1 s...10 s 0.1 s 10 s Table 7 Setting range for delay time T2 1. MENU > F3 (Control Parameters) > F2 (Voltage Regulation) > 8x. <08> Delay Time T1. 2. Press F4 in order to highlight the position. 3. Press F1 to increase the value or F5 to reduce it. 4. Press to save the setting. The delay time T2 is set. 22 Maschinenfabrik Reinhausen 2012

23 4.4 Displaying the info screen Information on the device can be viewed here. The following information is displayed: Device model Firmware version number Serial number RAM Additional cards MENU > F5 (Info) <00> Info By pressing, the following information is also displayed: Measurement values (<01> 1x ) Calculated measurement values (<02> 2x ) Functional reliability of the LEDs (<03> 3x ) MIO card digital inputs (terminals X4:13 - X4:24) (<04> 4x ) MIO card digital outputs (terminals X3:3 - X4:12) (<05> 5x ) Default parameters (<06> 6x ) Maschinenfabrik Reinhausen

24 Memory overview (<07> 7x ) Event overview (8x ) 24 Maschinenfabrik Reinhausen 2012

25

26 /02 EN 03/12 Maschinenfabrik Reinhausen GmbH Fon: +49 (0) Falkensteinstraße 8 Fax: +49 (0) Regensburg sales@reinhausen.com Internet: