A New High-performance Controller: High Resolution, High Speed, and High Input Accuracy. With Logic Operations and preventive maintenance functions.

Transcription

1 Advaned Digital Temperature Controller E5CN-H (48 x 48 mm) A New High-performane Controller: High Resolution, High Speed, and High Input Auray. With Logi Operations and preventive maintenane funtions. High-resolution display with 5 digits/. C display in a ompat Controller (48 x 48 mm). High-speed sampling yle of 6 ms. High Auray Thermoouple/Pt input: ±.% of PV Analog input: ±.% FS Universal inputs on all models (thermoouple, PT, analog) to handle various sensors with one Controller. A PV/SV-status display funtion an be set to alternate displaying the PV or SV and the status of the Temperature Controller (auto/manual, RUN/STOP and alarms). Flexible ontat outputs with logi operations (AND, OR, and delays) set from the Support Software (C-Thermo Ver. 4.) Preventive maintenane for relays using a Control Output / Counter. ain I/O Funtions mm E5CN-H Refer to Safety Preautions on page 8. E5CN-H 2-line Display: PV and SV Event Inputs None Two Universal Sensor Inputs Universal thermoouple/pt/analog (urrent/voltage) inputs. Indiation Auray Thermoouple/Pt input: ±.% of PV Analog input: ±.% FS Control Output 2 None Voltage output (for driving SSR) 5-digit, segment display with high resolution of. C Auxiliary Outputs Two Auto/manual swithing Temperature Controller status display Simple program funtion Logi operations Control output / ount alarm PV hange rate alarm odels optional with RS-485 or RS-232C ommuniations Sampling Period and ontrol update 6 ms Control Output Relay output Voltage output (for driving SSR) Current output Linear voltage output This data sheet is provided as a guideline for seleting produts. Be sure to refer to the following user manuals for appliation preautions and other information required for operation before attempting to use the produt. E5CN-H/E5AN-H/E5EN-H Digital Controllers User's anual Advaned Type (Cat. No. H7) E5CN-H/E5AN-H/E5EN-H Digital Controllers Communiations anual Advaned Type (Cat. No. H9) Advaned Digital Temperature Controller E5CN-H

2 Lineup E5CN-H Advaned Type Terminal blok Universal input ontrol output 2 auxiliary outputs 2 ontrol outputs 2 auxiliary outputs Note: All ontrollers an be used for Heating, Cooling and Heating & Cooling ontrol. odel Number Struture odel Number Legend Controllers E5CN-H@2@ Option Units E53-CN@@N Type H: Advaned 2. Control Output R: Relay output Q: Voltage output (for driving SSR) C: Current output V: Linear voltage output 3. Auxiliary Outputs 2: Two outputs 4. Option : Option Unit an be mounted. 5. Power Supply Voltage Blank: to 24 VAC D: 24 VAC/VDC 6. Terminal Cover -5: With terminal over Note: Casing olor is blak. White/Silver available on request.. Appliable Controller CN: E5CN-H 2. Funtion Blank: None Q: (voltage output for driving SSR) 3. Funtion 2 Blank: None H: Heater burnout/ssr failure/heater overurrent detetion (CT) HH: Heater burnout/ssr failure/heater overurrent detetion (For 3-phase heater appliations, 2x CT) B: Two event inputs : RS-232C ommuniations 3: RS-485 ommuniations H3: Heater burnout/ssr failure/heater overurrent detetion (CT) + RS-485 ommuniations HB: Heater burnout/ssr failure/heater overurrent detetion (CT) + Two event inputs HH3: Heater burnout/ssr failure/heater overurrent detetion (For 3-phase heater appliations, 2x CT) + RS-485 ommuniations H: Heater burnout/ssr failure/heater overurrent detetion (CT)/RS-232C ommuniations F: Transfer output BF: Two event inputs/transfer output 4. Version N2 Note: Not all ombinations of funtion and funtion 2 speifiations are possible for Option Units ((E53-CN@@N2)). 2 Advaned Digital Temperature Controller E5CN-H

3 Ordering Information Controllers /6 DIN (W H D) Size Case Color Power supply voltage Auxiliary output Control output odel Blak to 24 VAC 2 24 VAC/VDC 2 Note: Add power supply voltage to model to omplete ordering ode (ie. E5CN-HR2-5 AC-24 or E5CN-HR2D-5 AC/DC24). Option Units One of the following Option Units an be mounted to provide the E5CN with additional funtions. Event inputs Event inputs Funtions (Voltage for driving SSR) Relay output Voltage output (for driving SSR) Current output Linear voltage output Relay output Voltage output (for driving SSR) Current output Linear voltage output E5CN-HR2-5 E5CN-HQ2-5 E5CN-HC2-5 E5CN-HV2-5 E5CN-HR2D-5 E5CN-HQ2D-5 E5CN-HC2D-5 E5CN-HV2D-5 odel E53-CNBN2 E53-CNQBN2 Event inputs Heater burnout/ssr failure/ Heater overurrent detetion E53-CNHBN2 Event inputs Transfer Output E53-CNBFN2 Communiations RS-232C E53-CNN2 Communiations RS-232C Communiations RS-232C Communiations RS-485 Communiations RS-485 Communiations RS-485 Communiations RS-485 (Voltage for driving SSR) (Voltage for driving SSR) (Voltage for driving SSR) (Voltage for driving SSR) (Voltage for driving SSR) Transfer Output Heater burnout/ssr failure/ Heater overurrent detetion Heater burnout/ssr failure/ Heater overurrent detetion 3-phase heater burnout/ssr failure/ Heater overurrent detetion Heater burnout/ssr failure/ Heater overurrent detetion 3-phase heater burnout/ssr failure/ Heater overurrent detetion E53-CNQN2 E53-CNHN2 E53-CN3N2 E53-CNQ3N2 E53-CNH3N2 E53-CNHH3N2 E53-CNQFN2 E53-CNQHN2 E53-CNQHHN2 Aessories (Order Separately) USB-Serial Conversion Cable Terminal Cover Note:. The Terminal Cover omes with the E5CN-@@@-5 models. 2. The E53-COV annot be used. Waterproof Paking odel E58-CIFQ odel E53-COV7 odel Y92S-29 Note: Waterproof Paking is inluded with the ontroller only for models with terminal bloks. Current Transformers (CTs) Adapter Hole diameter odel 5.8 dia. E54-CT 2. dia. E54-CT3 Connetable models Terminal type Note: Use this Adapter when the panel has been previously prepared for the E5B@. C-Thermo Support Software odel EST2-2C-V4 odel Y92F-45 Advaned Digital Temperature Controller E5CN-H 3

4 Speifiations Ratings Power supply voltage Operating voltage range Power onsumption Sensor input Input impedane Control method Relay output Control output Auxiliary output Event input Logi operations Transfer outputs R input Voltage output (for driving SSR) Current output No D in model number: to 24 VAC, 5/6 Hz D in model number: 24 VAC, 5/6 Hz; 24 VDC 85% to % of rated supply voltage to 24 VAC: 8.5 VA (max.) (E5CN-HR2 at VAC: 3. VA) 24 VAC/VDC: 5.5 VA (24 VAC)/3.5 W (24 VDC) (max.) (E5CN-HR2D at 24 VAC: 2.7 VA) Any of the following an be seleted (i.e., fully universal input). Thermoouple: K, J, T, E, L, U, N, R, S, B, W, or PL II Platinum resistane thermometer: Pt or JPt Current input: 4 to 2 ma or to 2 ma Voltage input: to 5 V, to 5 V, or to V Current input: Ω max., Voltage input: Ω min. (Use a : onnetion when onneting the ES2-HB.) / ontrol or 2-PID ontrol (with auto-tuning) ST-NO, 25 VAC, 3 A (resistive load), eletrial life:, operations, minimum appliable load: 5 V, ma Output voltage: 2 VDC ±% (PNP), max. load urrent: 2 ma, with short-iruit protetion iruit 4 to 2 ma DC/ to 2 ma DC, load: 6 Ω max., resolution: approx., Linear voltage output to VDC (load: kω min.), Resolution: Approx., Number of outputs 2 Output speifiations Number of inputs 2 External ontat input speifiations Number of operations Operations Outputs Setting method Work bit assignments Number of outputs Output speifiations Indiation method Bank swithing Other funtions Ambient operating temperature Relay output: ST-NO, 25 VAC, 3 A (resistive load), eletrial life:, operations, minimum appliable load: 5 V, ma Contat input: : kω max., : kω min. Non-ontat input: : Residual voltage:.5 V max., : Leakage urrent:. ma max. Current flow: Approx. 7 ma per ontat 8 max. (Combinations an be made using work bits.) Logi operation: Any of the following four patterns an be seleted. The input status may be inverted. (A and B) or (C and D), (A or C) and (B or D), A or B or C or D, A and B and C and D (A, B, C, and D are four inputs.) Delay: delay or delay for the results of the logi operation given above. Setting time: to 9999 s or to 9999 min Output inversion: Possible One work bit per operation Any of the following an be assigned to up to eight work bits (logi operation results): Event input operations, auxiliary outputs, or ontrol outputs. max. Current output: 4 to 2 ma DC, Load: 6 Ω max., Resolution at 4 to 2 ma: Approx., Not supported Ambient operating humidity 25% to 85% Storage temperature Digital setting using front panel keys -segment digital display and individual indiators (7-segments display emulation also possible) Charater height: PV: mm, SV: 6.5 mm Supported (number of banks: 8) Loal, alarm settings, PID sets (PID onstants, V upper limit, V lower limit, et.) anual output, heating/ooling ontrol, loop burnout alarm, ramp, other alarm funtions, heater burnout detetion, 4% AT, % AT, V limiter, input digital filter, self-tuning, temperature input shift, run/stop, protetion funtions, ontrol output / ounter, extration of square root, V hange rate limit, PV/SV status display, logi operations, automati ooling oeffiient adjustment to 55 C (with no ondensation or iing), for 3-year warranty: to 5 C 25 to 65 C (with no ondensation or iing) For models with urrent outputs, ontrol output an be used as a transfer output. 4 Advaned Digital Temperature Controller E5CN-H

5 Input Ranges Thermoouple/Platinum Resistane Thermometer/Analog Input (Fully Universal Inputs) Input type Platinum resistane Thermoouple thermometer Name Pt JPt K J T E L U N R S B W PL II Temperature range ( C) Setting number 4 to 2 ma 2 ma to Analog input Usable in the following ranges by saling: to 324, to 324., to 324., or to Shaded settings are the default settings. The appliable standards for the input types are as follows: K, J, T, E, N, R, S, B: JIS C , IEC 584- L: Fe-CuNi, DIN U: Cu-CuNi, DIN W: W5Re/W26Re, AST E JPt: JIS C , JIS C Pt: JIS C , IEC 75 PL II: Aording to Platinel II eletromotive fore harts from BASF (previously Engelhard) to 5V to 5V to V Advaned Digital Temperature Controller E5CN-H 5

6 Alarm Outputs Eah alarm an be independently set to one of the following alarm types. The default is 2: Upper limit. Auxiliary outputs are alloated for alarms. delays and delays ( to 999 s) an also be speified. Note: For models with heater burnout, SSR failure, and heater overurrent detetion, alarm will be an OR output of the alarm seleted from the following alarm types and the alarms for heater burnout, SSR failure, and heater overurrent. To output only a heater burnout alarm, SSR failure alarm, and heater overurrent alarm for alarm, set the alarm type to (i.e., no alarm funtion). Set value Alarm type Alarm funtion Upper- and lowerlimit 2 Upper limit 3 Lower limit Upper- and lowerlimit range Upper- and lowerlimit with standby sequene Upper-limit with standby sequene Lower-limit with standby sequene Absolute-value upper-limit Absolute-value lower-limit Absolute-value upper-limit with standby sequene Absolute-value lower-limit with standby sequene LBA (for alarm only) PV hange rate alarm Alarm output operation When is positive Output L L L H H H When is negative. With set values, 4 and 5, the upper and lower limit values an be set independently for eah alarm type, and are expressed as L and H. 2. Set value:, Upper- and lower-limit alarm Case L H H <, L > H < L Case 2 L H H >, L < H > L 3. Set value: 4, Upper- and lower-limit range Case L H H <, L > H < L Case 2 L H H >, L < H > L Case 3 (Always ) 4. Set value: 5, Upper- and lower-limit with standby sequene For Upper- and Lower-Limit Alarm Desribed Above Case and 2 Always when the upper-limit and lower-limit hysteresis overlaps. Case 3: Always 5. Set value: 5, Upper- and lower-limit with standby sequene Always when the upper-limit and lower-limit hysteresis overlaps. H H L H L L Case 3 (Always ) H H L H L L H <, L < H <, L > H L H >, L < H L H <, L < H <, L > H L H >, L < H L 6 Advaned Digital Temperature Controller E5CN-H

7 Charateristis Indiation auray Transfer output auray Influene of temperature 2 Influene of voltage 2 Input sampling period Hysteresis Thermoouple: (±.% of indiated value or ± C, whihever is greater) ± digit max. Platinum resistane thermometer: (±.% of indiated value or ±.5 C, whihever is greater) ± digit max. Analog input: ±.% FS ± digit max. CT input: ±5% FS ± digit max. ±.3% FS max. Thermoouple input (R, S, B, W, PLII): (±% of PV or ± C, whihever is greater) ± digit max. Other thermoouple input: (±% of PV or ±4 C, whihever is greater) ± digit max. 3 Platinum resistane thermometer: (±% of PV or ±2 C, whihever is greater) ± digit max. Analog input: (±%FS) ± digit max. 6 ms Temperature input:. to 324. C or F (in units of. C or F) Analog input:.% to 99.99% FS (in units of.% FS) Proportional band (P) Temperature input:. to 324. C or F (in units of. C or F) Analog input:.% to 999.9% FS (in units of.% FS) Integral time (I). to 324. s (in units of. s) Derivative time (D). to 324. s (in units of. s) Control period.5, to 99 s (in units of s) anual reset value. to.% (in units of.%) Alarm setting range Affet of signal soure resistane Insulation resistane Dieletri strength Vibration alfuntion resistane Destrution Shok alfuntion resistane Destrution Weight Degree of protetion emory protetion Setup Tool Setup Tool port Standards EC Approved standards Conformed standards 9999 to 324 (deimal point position depends on input type) Thermoouple:. C/Ω max. ( Ω max.) Platinum resistane thermometer:. C/Ω max. ( Ω max.) 2 Ω min. (at 5 VDC) 2,3 VAC, 5 or 6 Hz for min (between terminals with different harge) to 55 Hz, 2 m/s 2 for min eah in, Y, and Z diretions to 55 Hz,.75-mm single amplitude for 2 hrs eah in, Y, and Z diretions m/s 2, 3 times eah in, Y, and Z diretions 3 m/s 2, 3 times eah in, Y, and Z diretions Controller: Approx. g, ounting Braket: Approx. g Front panel: IP66, Rear ase: IP2, Terminals: IP Non-volatile memory (number of writes:,, times) C-Thermo version 4. or higher Provided on the bottom of the E5CN-H. Use this port to onnet a omputer to the E5CN-H. An E58-CIFQ USB-Serial Conversion Cable is required to onnet the omputer to the E5CN-H. 4 UL 6-, CSA C22.2 No. - EN 6- (IEC 6-): Pollution level 2, overurrent ategory II EI: EN 626 Radiated Interferene Eletromagneti Field Strength: EN 55 Group, lass A Noise Terminal Voltage: EN 55 Group, lass A ES: EN 626 ESD Immunity: EN Eletromagneti Field Immunity: EN Burst Noise Immunity: EN Conduted Disturbane Immunity: EN Surge Immunity: EN Power Frequeny agneti Field Immunity: EN Voltage Dip/Interrupting Immunity: EN The indiation auray of K thermoouples in the 2 to C range, T and N thermoouples at a temperature of C max., and U and L thermoouples at any temperatures is ±2 C ± digit max. The indiation auray of the B thermoouple at a temperature of 4 C max. is not speified. The indiation auray of B thermoouples in the 4 to 8 C range is ±3 C max. The indiation auray of the R and S thermoouples at a temperature of 2 C max. is ±3 C ± digit max. The indiation auray of W thermoouples is ±.3 of PV or ±3 C, whihever is greater, ± digit max. The indiation auray of PL II thermoouples is ±.3 of PV or ±2 C, whihever is greater, ± digit max. 2. Ambient temperature: C to 23 C to 55 C, Voltage range: % to % of rated voltage 3. K thermoouple at C max.: ± C max. 4. External ommuniations (RS-232C or RS-485) and able ommuniations for the Setup Tool an be used at the same time. Advaned Digital Temperature Controller E5CN-H 7

8 USB-Serial Conversion Cable Appliable OS Appliable software Windows 2, P, or Vista Thermo ini, C-Thermo version 4. or higher Appliable models E5AN/E5EN/E5CN/E5CN-U/ E5AN-H/E5EN-H/E5CN-H USB interfae standard Conforms to USB Speifiation.. DTE speed Connetor speifiations Power supply Power supply voltage Current onsumption Ambient operating temperature 384 bps Computer: USB (type A plug) Temperature Controller: Setup Tool port (on bottom of Controller) Bus power (Supplied from USB host ontroller.) 5 VDC 7 ma Ambient operating humidity % to 8% to 55 C (with no ondensation or iing) Storage temperature 2 to 6 C (with no ondensation or iing) Storage humidity % to 8% Altitude Weight 2, m max. Approx. g Note: A driver must be installed in the personal omputer. Refer to installation information in the operation manual for the Conversion Cable. Communiations Speifiations Transmission line onnetion method Communiations Synhronization method Protool Baud rate Transmission ode Data bit length Stop bit length Error detetion Flow ontrol Interfae Retry funtion Communiations buffer Communiations response wait time RS-485: ultipoint RS-232C: Point-to-point RS-485 (two-wire, half duplex)/rs-232c Start-stop synhronization CompoWay/F, SYSWAY, or odbus 2, 24, 48, 96, 92, 384, or 576 bps ASCII (CompoWay/F, SYSWAY) RTU (odbus) 7 or 8 bits or 2 bits Vertial parity (none, even, odd) Frame hek sequene (FCS) with SYSWAY Blok hek harater (BCC) with CompoWay/F or CRC-6 odbus None RS-485, RS-232C None 27 bytes to 99 ms Default: 2 ms The baud rate, data bit length, stop bit length, and vertial parity an be individually set using the Communiations Setting. Current Transformer (Order Separately) Ratings Dieletri strength, VAC for min Vibration resistane 5 Hz, 98 m/s 2 Weight Aessories (E54-CT3 only) E54-CT: Approx..5 g, E54-CT3: Approx. 5 g Armatures (2) Plugs (2) Heater Burnout Alarms, SSR Failure Alarms, and Heater Overurrent Alarms CT input (for heater urrent detetion) aximum heater urrent Input urrent indiation auray Heater burnout alarm setting range SSR failure alarm setting range 2 Heater overurrent alarm setting range 3 odels with detetion for singlephase heaters: One input odels with detetion for singlephase or three-phase heaters: Two inputs 5 A AC ±5% FS ± digit max.. to 49.9 A (in units of. A) inimum detetion time: ms. to 49.9 A (in units of. A) inimum detetion time: ms. to 49.9 A (in units of. A) inimum detetion time: ms. For heater burnout alarms, the heater urrent will be measured when the ontrol output is, and the output assigned to the alarm funtion will turn if the heater urrent is lower than the set value (i.e., heater burnout detetion urrent value). 2. For SSR failure alarms, the heater urrent will be measured when the ontrol output is, and the output assigned to the alarm funtion will turn if the heater urrent is higher than the set value (i.e., SSR failure detetion urrent value). 3. For heater overurrent alarms, the heater urrent will be measured when the ontrol output is, and the output assigned to the alarm funtion will turn if the heater urrent is higher than the set value (i.e., heater overurrent detetion urrent value). Eletrial Life Expetany Curve for Relays (Referene Values) Life ( 4 operations) E5CN-H 25 VAC, 3 VDC (resistive load) osφ = Swithing urrent (A) 8 Advaned Digital Temperature Controller E5CN-H

9 External Connetions A voltage output (ontrol output, for driving SSR) is not eletrially insulated from the internal iruits. When using a grounding thermoouple, do not onnet any of the ontrol output terminals to ground. If the ontrol output terminals are onneted to ground, errors will our in the measured temperature values as a result of leakage urrent. Controllers Control output Relay output 25 VAC, 3 A (resistive load) Voltage output (for driving SSR) 2 VDC, 2 ma Linear voltage output to VAC Load kω max. Current output to 2 ma DC 4 to 2 ma DC Load 6 Ω max. ma D T D T V Control output D T ma V t/ Pt A B B Auxiliary outputs (relay outputs) 25 VAC, 3 A (resistive load) Auxiliary output 2 Auxiliary output? Input power supply A heater burnout alarm, SSR failure, heater overurrent alarm, or input alarm is sent to the output to whih the alarm funtion is assigned. to 24 VAC 24 VAC/VDC (no polarity) Option Units E53-CNBN2 Event Inputs E53-CNQBN2 E53-CNHBN2 E53-CNBFN2 Event Inputs and Control Output 2 Event Inputs and CT Event Inputs and Transfer Output EV EV2 DO NOT DO NOT 2 4 EV2 EV 2 VDC 2 ma 2 4 EV2 CT EV EV EV2 4 Transfer output 4 to 2 ma DC (Load 6 Ω max.) CT2 E53-CNQHHN2 Control Output 2 and CT2 2 VDC 2 ma CT 2 4 E53-CNQFN2 E53-CNN2 E53-CNHN2 E53-CNQN2 Control Output 2 and Communiations Communiations Communiations (RS-232) Transfer Output (RS-232) (RS-232) and CT and Control Output 2 RS-232C RS-232C RS-232C SD SD SD 2 VDC 2 ma 2 RD 2 RD 2 RD 2 DO NOT SG SG SG DO NOT to 2 ma DC Transfer output DO NOT CT (Load 6 Ω 2 VDC 2 ma max.) E53-CN3N2 E53-CNQ3N2 E53-CNH3N2 E53-CNHH3N2 Communiations (RS-485) Communiations (RS-485) and Control Output 2 Communiations (RS-485) and CT Communiations (RS-485) and CT2 E53-CNQHN2 Control Output 2 and CT B (+) RS A ( ) DO NOT DO NOT 4 DO NOT B (+) RS A ( ) DO NOT 4 2 VDC 2 ma B (+) RS A ( ) DO NOT 4 CT B (+) RS A ( ) CT2 4 CT 2 VDC 2 ma DO NOT CT 2 4 Note: Wire all voltage input terminals orretly. The Controller may fail if voltage input terminals are wired inorretly. Advaned Digital Temperature Controller E5CN-H 9

10 Nomenlature E5CN-H Temperature unit Operation indiators SUB SUB2 SUB3 HA No. display OUT STOP OUT2 CW ANU No. 2 display Key Up Key E5CN-H ode Key Down Key Dimensions (Unit: mm) E5CN-H Panel Cutout ounted Separately Group ounted (48 number of units 2.5) Waterproof Paking (Aessory) ounting Adapter (Aessory) Terminal Cover (E53-COV7) (Aessory) 6 min Note: The terminal blok annot be removed Group mounting does not allow waterproofing. Reommended panel thikness is to 5mm. Group mounting is not possible in the vertial diretion. (aintain the speified mounting spae between Controllers.) To mount the Controller so that it is waterproof, insert the waterproof paking onto the Controller. When two or more Controllers are mounted, make sure that the surrounding temperature does not exeed the allowable operating temperature speified in the speifiations. Aessories (Order Separately) USB-Serial Conversion Cable E58-CIFQ (2,) 25 LED indiator,765 (SD) USB onnetor (type A plug) LED indiator (RD) Serial onnetor Advaned Digital Temperature Controller E5CN-H

11 Terminal Cover E53-COV7 Waterproof Paking Y92S-29 (for DIN 48 48) Note: The E53-COV an not be used. Order the Waterproof Paking separately if it beomes lost or damaged. The Waterproof Paking an be used to ahieve an IP66 degree of protetion. (Deterioration, shrinking, or hardening of the waterproof paking may our depending on the operating environment. Therefore, periodi replaement is reommended to ensure the level of waterproofing speified in IP66. The time for periodi replaement depends on the operating environment. Be sure to onfirm this point at your site. Consider one year a rough standard. OR shall not be liable for the level of water resistane if the ustomer does not perform periodi replaement.) The Waterproof Paking does not need to be attahed if a waterproof struture is not required. 9. Current Transformers E54-CT dia E54-CT Thru-urrent (Io) vs. Output Voltage (Eo) (Referene Values) aximum ontinuous heater urrent: 5 A (5/6 Hz) Number of windings: 4±2 Winding resistane: 8±2 Ω E54-CT Two, 3.5 dia dia. Output voltage (Eo) V (r.m.s.) V 5 Hz mv kω Ω RL = Ω Distortion fator % 3% % 2 dia. 9 μv ma, A 4 4 Thru-urrent (Io) A (r.m.s.) E54-CT3 Aessory Armature Approx. 3 dia. Plug 8 Two, 3 (depth: 4) 3 Connetion Example Armature Plug Lead E54-CT3 Thru-urrent (Io) vs. Output Voltage (Eo) (Referene Values) aximum ontinuous heater urrent: 2 A (5/6 Hz) (aximum ontinuous heater urrent for an OR Temperature Controller is 5 A.) Number of windings: 4±2 Winding resistane: 8±.8 Ω Output voltage (Eo) V (r.m.s.) V 5 Hz mv kω 5 Ω Ω 5 Ω RL = Ω Distortion fator % 3% % Approx. 6 dia. μv (22) ma, A Thru-urrent (Io) A (r.m.s.) Advaned Digital Temperature Controller E5CN-H

12 Adapter Y92F-45 Note: Use this Adapter when the panel has already been prepared for the to Fixture (Aessory) ounted to E5CN-H Panel ( to 8 mm) (to bak of E5CN-H) 2 Advaned Digital Temperature Controller E5CN-H

13 Start in manual mode. Power Start in automati mode. anual mode Press the O Key or the PF Key for at least s. 4 3 a- m Press the O Key for at least 3 s while a-m is displayed. (a-m will flash after st seond.) Operation Press the O Key less than s. Press the O Key less than s. PID Setting Press the O Key less than s. Adjustment Press the O Key less than s. Bank Setting Press the O + Keys for at least 3 s. (Display will flash after st seond.) 25.. Press the O+ Keys for at least s. anual Control Protet Press the O Key for at least s Press the O Key for at least 3 s. (Display will flash after st seond.) Note: The time taken to move to the protet level an be adjusted by hanging the ove to protet level time setting. Control stops. Press the O Key for at least s. Initial Setting Advaned Funtion Setting Communiations Setting Press the O Key for less than s. Input password while amov is displayed. (Set value 69) Input password. Control in progress. You an return to the operation level by exeuting a software reset. 2. It is not possible to move to other levels from the alibration level by operating the keys on the front panel. It an be done only by first turning the power. 3. From the manual ontrol level, key operations an be used to move to the operation level only. Error Displays (Troubleshooting) When an error ours, the No. display shows the error ode. Take neessary measure aording to the error ode, referring the table below. No. display eaning Ation s.err (S. Err) e333 (E333) e (E) Input error A/D onverter error emory error Calibration Control stopped hange Chek the wiring of inputs for miswiring, disonnetions, and short-iruits and hek the input type. Turn the power then bak again. If the display remains the same, the ontroller must be repaired. If the display is restored to normal, then a probable ause an be external noise affeting the ontrol system. Chek for external noise. Turn the power then bak again. If the display remains the same, the ontroller must be repaired. If the display is restored to normal, then a probable ause an be external noise affeting the ontrol system. Chek for external noise. Not displayed for some models Control output Status at error Alarm output Note: If the input value exeeds the display limit (-9999 to 324), though it is within the ontrol range, will be displayed under and above 324. Under these onditions, ontrol output and alarm output will operate normally. For details on the ontrol range, refer to the E5CN-H/E5AN-H/E5EN-H Digital Controllers User's anual Advaned Type (Cat. No. H7). These errors are displayed only when the PV/ is displayed. Errors are not displayed for other displays. 2 Operates as above the upper limit. Advaned Digital Temperature Controller E5CN-H

14 Advaned Type Some parameters are not displayed depending on the model of the Controller and parameter settings. For details, refer to the E5CN-H/E5AN-H/ E5EN-H Digital Controllers User's anual Advaned Type (Cat. No. H7). Power anual Control Protet Operation Adjustment Bank Setting PID Setting onitor/setting Item Initial Setting Communiations Setting Advaned Funtion Setting PID Setting Press the O Key less than s. Bank Setting Press the O Key less than s. Press the O Key less than s. Display PID Seletion d.pid PID d.pid PID2 2 d.pid 3 PID3 Display Bank Seletion d.bnk Bank d.bnk Bank d.bnk 2 Bank2 d.pid 8 PID8 d.bnk 7 Bank7.p 8..i 233..d 4..olh..oll -5..aut 2..s..lba 8.p PID 8 Proportional Band 8. 8.i PID 8 Integral Time d PID 8 Derivative Time 4. 8.olh PID 8 V Upper Limit. 8.oll PID 8 V Lower Limit aut PID 8 Automati Seletion 2. Range Upper Limit 8.s PID 8 Cooling Coeffiient. 8.lba PID 8 LBA Detetion Time.lsp..pid.spr.a-..ah..al..a-2..a2h..a2l..a-3..a3h..a3l..sok.wtb 7.lsp. 7.pid 7.spr Bank 7 Ramp Set Value 7.a- Bank 7. Bank 7 7.ah. Upper Limit Bank 7 7.al. Bank 7 Bank 7 PID Set No. Lower Limit Set either of these parameters 7.a-2 Bank 7. 2 Bank 7 7.a2h. Upper Limit 2 7.a2l. 7.a-3 Bank 7. 3 Bank 7 7.a3h. Upper Limit 3 Bank 7 Lower Limit 2 Bank 7 7.a3l. Lower Limit 3 Set either of these parameters Set either of these parameters 7.sok Bank 7 Soak Time 7.wtb Bank 7 Wait Band 4 Advaned Digital Temperature Controller E5CN-H

15 Power Starting in manual mode. anual Control 25.. PV/V PID Control only Press the O Key for at least s. Starting in automati mode. Adjustment Press the O Key less than s. Operation Press the O and Keys for at least 3 s. l.a d j at m wt ir da t Heater Current. Value onitor hb Heater Burnout. Detetion o Heater Overurrent 5. Detetion t2. hb2. o2 5. lr. hs 5. lr2. hs2 5. ins. insh Upper Limit Temperature. Input Shift Value 2-point shift insl. Adjustment Display Displayed only one when entering adjustment level. AT Exeute/Canel Communiations Writing Infrared Communiations Use Heater Current 2 Value onitor Heater Burnout Detetion 2 Heater Overurrent Detetion 2 Leakage Current onitor HS Alarm Leakage Current 2 onitor HS Alarm 2 Temperature Input Shift -point shift Lower Limit Temperature Input Shift Value Set either of these parameters. p 8. i 233. d 4. - s. - db. of -r 5. hy s. h ys. so ak wt -b mv -s. mv -e. sp rt ol -h. ol -l -5. or l. db Position Proportional Dead Band 2. o -h. 8 sq rp. Proportional Band Integral Time Derivative Time PID settings Cooling Coeffiient Heating/ooling Dead Band anual Reset Value Clear the set during stabilization of P or PD ontrol. Hysteresis (Heating) Hysteresis settings Hysteresis (Cooling) Soak Time Wait Band V at Stop V at PV Error Ramp Set Value V Upper Limit V Lower Limit V Change Rate Limit Open/Close Hysteresis Extration of Square Root Low-ut Point Press the O Key for at least 3 s a- m ba nk sp-m. t Heater Current Value. onitor t2 Heater Current 2 Value. onitor lr. lr2. prst rset sktr Proess Value Added when Additional PV display is. Proess Value/ Set Point Auto/anual Swith PID ontrol only. Added when auto/manual selet addition is. Bank No. Set Point During Ramp Leakage Current onitor Leakage Current 2 onitor Program Start Soak Time Remain r- s run al -. al h. al l. al -2. al 2h. al 2l. al -3. al 3h. al 3l. o. - o. RUN/STOP Upper Limit Lower Limit 2 Upper Limit 2 Lower Limit 2 3 Upper Limit 3 Lower Limit 3 Set either of these parameters. Set either of these parameters. Set either of these parameters. V onitor (Heating) V onitor (Cooling) Press the O and Keys for at least s. Advaned Digital Temperature Controller E5CN-H

16 Press the O Key for at least s. Press the O Key for at least 3 s. Other than the Auto/anual Swith display Press the O Key less than s. Initial Setting pmov oapt ipt wtpt of f pmsk on prlp Protet The time taken to move to the protet level an be adjusted by hanging the "ove to protet level time" setting. ove to Protet : Displayed only when a password is set. Restrits moving to protet level. Operation/Adjustment Protet: Restrits displaying and modifying menus in operation, adjustment, and manual ontrol levels. Initial Setting/ Communiations Protet: This protet level restrits movement to the initial setting, ommuniations setting, and advaned funtion setting levels. Setting Change Protet: Protets hanges to setups by operating the front panel keys. Parameter ask Enable: Displayed only when a parameter mask is set. Password to ove to Protet : Password setting Press the O Key less than s. Communiations Setting Displayed only for models with ommuniations. Changes are effetive after yling power or after a software reset. psel wf u-no bps 9. 6 len 7 sbit 2 prty e ven sdwt 2 Protool Setting: Swithes between CompoWay/F (SYSWAY) and odbus. Communiations Unit No. Communiations Baud Rate CompoWay/F (SYSWAY) only Communiations Data Length Communiations Stop Bits Communiations Parity Send Data Wait Time in-t 5 in-h in-l dp d-u sl-h. sl-l - 2. ntl pi d Standard or s-h Heating/Cooling st nd ST (Self-tuning) st on ptrn of f pbnk 7 p 2 -p 2 orev or- r Input Type Saling Upper Limit Saling Lower Limit Deimal Point For input type of analog Temperature Unit C, F For input type of temperature Upper Limit Limit the set point Lower Limit PID / For input type of temperature, standard ontrol, or PID Program Pattern Valid Program Bank When assigning PID or ontrol output to / output Control Period (Heating) Set the / output yle. Control Period (Cooling) Diret/Reverse Operation alt2 2 alh2. 2 alt3 2 alh3.2 tr-t tr-h Transfer Output Upper Limit. tr-l. o-t 4-2 ev-b ev- Event Input Assignment n one ev-2 sto p sqr Extration of Square Root Enable amov Alarm 2 Type Alarm 2 Hysteresis Alarm 3 Type Alarm 3 Hysteresis Transfer Output Type Linear output Transfer Output Lower Limit Linear Current Output Linear output Bank Numbers Used Event Input Assignment 2 ove to Advaned Funtion Setting : Displayed when initial setting/ ommuniations protet is set to. ove by setting password ( 69). alt 2 alh. 2 Alarm Type Alarm Hysteresis 6 Advaned Digital Temperature Controller E5CN-H

17 Power anual Control Protet Operation Adjustment Bank Setting PID Setting onitor/setting Item Initial Setting Communiations Setting Advaned Funtion Setting Press the O Key for at least s. Advaned Funtion Setting init of f spru m rest a sbn n- o sb2n n-o sb3n n- o hbu on hbl hbh Heater Burnout Hysteresis. st-b. α alfa.65 at-g. at-h. 8 lma 2. inf. pvad of f Parameter Initialization Ramp Time Unit Standby Sequene Reset Auxiliary Output Open in Alarm Auxiliary Output 2 Open in Alarm Auxiliary Output 3 Open in Alarm HB / Heater Burnout Lath ST Stable Range AT Calulated Gain AT Hysteresis Limit Cyle V Amplitude Input Digital Filter Additional PV Display o-dp of f ret alt a2lt of f a3lt of f prlt 3 sero j on rlrv of f olr red pv-b 5. aon a2on a3on aof Alarm Delay a2of a3of V Display Automati Display Return Time Alarm Lath Alarm 2 Lath Alarm 3 Lath ove to Protet Time Input Error Output Cold Juntion Compensation ethod B Command Logi Swithing PV Change Color PV Stable Band Alarm Delay Alarm 2 Delay Alarm 3 Delay Alarm 2 Delay Alarm 3 Delay istp i ns mvse amad on rt of f hsu on hsl of f hsh. lba lbal LBA 8. lbab 3. out o out2 Control Output 2 Assignment n one sub alm sub2 Auxiliary Output 2 Assignment a lm2 sel on t-u m Input Shift Type V at Stop and Error Addition Auto/anual Selet Addition RT HS Alarm Use HS Alarm Lath HS Alarm Hysteresis LBA Detetion Time LBA Band Control Output Assignment Auxiliary Output Assignment Charater Selet Soak Time Unit alsp sp -m sptr pidi pv pidh.5 p-db. manl pmvd pvrp 7 sa ou on ol Heater Overurrent Lath oh. Alarm Seletion Traking PID Set Automati Seletion Data PID Set Automati Seletion Hysteresis PV Dead Band anual V Limit Enable Diret Setting of Position Proportional V PV Rate of Change Calulation Period Automati Cooling Coeffiient Adjustment Heater Overurrent Use Heater Overurrent Hysteresis spdp 4 odsl o pvdp on pvst svst d.ref.25 ram ra2m ra ra2 ra mov "PV/" Display Sreen Seletion V Display Seletion PV Deimal Point Display PV Status Display Funtion SV Status Display Funtion Display Refresh Period Control Output / Count onitor Control Output 2 / Count onitor Control Output / Count Alarm Set Value Control Output 2 / Count Alarm Set Value / Counter Reset ove to Calibration Advaned Digital Temperature Controller E5CN-H 7

18 Safety Preautions!CAUTI Do not touh the terminals while power is being supplied. Doing so may oasionally result in minor injury due to eletri shok. Do not allow piees of metal, wire lippings, or fine metalli shavings or filings from installation to enter the produt. Doing so may oasionally result in eletri shok, fire, or malfuntion. Do not use the produt where subjet to flammable or explosive gas. Otherwise, minor injury from explosion may oasionally our. Do not leave the able for the Support Software onneted to the produt. alfuntion may our due to noise in the able. Do not use the Temperature Controller or Conversion Cable if it is damaged. Doing so may oasionally result in minor eletri shok or fire. Never disassemble, modify, or repair the produt or touh any of the internal parts. inor eletri shok, fire, or malfuntion may oasionally our. CAUTI - Risk of Fire and Eletri Shok a) This produt is UL listed as Open Type Proess Control Equipment. It must be mounted in an enlosure that does not allow fire to esape externally. b) ore than one disonnet swith may be required to de-energize the equipment before serviing the produt. ) Signal inputs are SELV, limited energy. d) Caution: To redue the risk of fire or eletri shok, do not interonnet the outputs of different Class 2 iruits. 2 If the output relays are used past their life expetany, ontat fusing or burning may oasionally our. Always onsider the appliation onditions and use the output relays within their rated load and eletrial life expetany. The life expetany of output relays varies onsiderably with the output load and swithing onditions. Tighten the terminal srews to between.74 and.9 N m. 3 Loose srews may oasionally result in fire. Set the parameters of the produt so that they are suitable for the system being ontrolled. If they are not suitable, unexpeted operation may oasionally result in property damage or aidents. A malfuntion in the produt may oasionally make ontrol operations impossible or prevent alarm outputs, resulting in property damage. To maintain safety in the event of malfuntion of the produt, take appropriate safety measures, suh as installing a monitoring devie on a separate line. A semiondutor is used in the output setion of long-life relays. If exessive noise or surge is impressed on the output terminals, a short-iruit failure is likely to our. If the output remains shorted, fire will our due to overheating of the heater or other ause. Take measures in the overall system to prevent exessive temperature inrease and to prevent fire from spreading. Do not allow piees of metal or wire uttings to get inside the able onnetor for the Support Software. Failure to do so may oasionally result in minor eletri shok, fire, or damage to equipment. Do not allow dust and dirt to ollet between the pins in the onnetor on the Conversion Cable. Failure to do so may oasionally result in fire. When inserting the body of the Temperature Controller into the ase, onfirm that the hooks on the top and bottom are seurely engaged with the ase. If the body of the Temperature Controller is not inserted properly, faulty ontat in the terminal setion or redued water resistane may oasionally result in fire or malfuntion. When onneting the Control Output Unit to the soket, press it in until there is no gap between the Control Output Unit and the soket. Otherwise ontat faults in the onnetor pins may oasionally result in fire or malfuntion.. An SELV iruit is one separated from the power supply with double insulation or reinfored insulation, that does not exeed 3 V r.m.s. and 42.4 V peak or 6 VDC. 2. A lass 2 power supply is one tested and ertified by UL as having the urrent and voltage of the seondary output restrited to speifi levels. 3. The tightening torque for E5CN-U is.5 N m. Preautions for Safe Use Be sure to observe the following preautions to prevent malfuntion or adverse affets on the performane or funtionality of the produt. Not doing so may oasionally result in faulty operation.. This produt is speifially designed for indoor use only. Do not use this produt in the following plaes: Plaes diretly subjet to heat radiated from heating equipment. Plaes subjet to splashing liquid or oil atmosphere. Plaes subjet to diret sunlight. Plaes subjet to dust or orrosive gas (in partiular, sulfide gas and ammonia gas). Plaes subjet to intense temperature hange. Plaes subjet to iing and ondensation. Plaes subjet to vibration and large shoks. 2. Use and store the produt within the rated ambient temperature and humidity. Gang-mounting two or more Temperature Controllers, or mounting Temperature Controllers above eah other may ause heat to build up inside the Temperature Controllers, whih will shorten their servie life. In suh a ase, use fored ooling by fans or other means of air ventilation to ool down the Temperature Controllers. 3. To allow heat to esape, do not blok the area around the produt. Do not blok the ventilation holes on the produt. 4. Be sure to wire properly with orret polarity of terminals. 5. Use the speified size (3.5, width 7.2 mm or less) rimped terminals for wiring. To onnet bare wires to the terminal blok, use stranded or solid opper wires with a gage of AWG24 to AWG4 (equal to a ross-setional area of.25 to 2.8 mm 2 ). (The stripping length is 5 to 6 mm.) Up to two wires of the same size and type or two rimp terminals an be inserted into a single terminal. 6. Do not wire the terminals that are not used. 7. To avoid indutive noise, keep the wiring for the produt s terminal blok away from power ables arry high voltages or large urrents. Also, do not wire power lines together with or parallel to produt wiring. Using shielded ables and using separate onduits or duts is reommended. Attah a surge suppressor or noise filter to peripheral devies that generate noise (in partiular, motors, transformers, solenoids, magneti oils, or other equipment that have an indutane omponent). When a noise filter is used at the power supply, first hek the voltage or urrent, and attah the noise filter as lose as possible to the produt. Allow as muh spae as possible between the produt and devies that generate powerful high frequenies (high-frequeny welders, high-frequeny sewing mahines, et.) or surge. 8. Use this produt within the rated load and power supply. 9. ake sure that the rated voltage is attained within two seonds of turning the power using a swith or relay ontat. If the voltage is applied gradually, the power may not be reset or output malfuntions may our..ake sure that the Temperature Controller has 3 minutes or more to warm up after turning the power before starting atual ontrol operations to ensure the orret temperature display. 8 Advaned Digital Temperature Controller E5CN-H

19 .When exeuting self-tuning, turn power to the load (e.g., heater) at the same time as or before supplying power to the produt. If power is turned to the produt before turning power to the load, self-tuning will not be performed properly and optimum ontrol will not be ahieved. 2.A swith or iruit breaker must be provided lose to the produt. The swith or iruit breaker must be within easy reah of the operator, and must be marked as a disonneting means for this unit..always turn the power supply before pulling out the interior of the produt, and never touh nor apply shok to the terminals or eletroni omponents. When inserting the interior of the produt, do not allow the eletroni omponents to touh the ase. 4.Do not use paint thinner or similar hemial to lean with. Use standard grade alohol..design the system (e.g., ontrol panel) onsidering the 2 seonds of delay that the produt's output to be set after power. 6.The output may turn when shifting to ertain levels. Take this into onsideration when performing ontrol. 7.The number of EEPRO write operations is limited. Therefore, use RA write mode when frequently overwriting data during ommuniations or other operations. 8.Always touh a grounded piee of metal before touhing the Temperature Controller to disharge stati eletriity from your body. 9.Do not remove the terminal blok. Doing so may result in failure or malfuntion. 2.Control outputs (for driving SSR) that are voltage outputs are not isolated from the internal iruits. When using a grounded thermoouple, do not onnet any of the ontrol output terminals to ground. (Doing so may result in an unwanted iruit path, ausing error in the measured temperature.) 2.When replaing the body of the Temperature Controller, hek the ondition of the terminals. If orroded terminals are used, ontat failure in the terminals may ause the temperature inside the Temperature Controller to inrease, possibly resulting in fire. If the terminals are orroded, replae the ase as well. 22.Use suitable tools when taking the Temperature Controller apart for disposal. Sharp parts inside the Temperature Controller may ause injury. 23.Before onneting an Output Unit, onfirm the speifiations and thoroughly read relevant information in the datasheet and manual for the Temperature Controller. 24.Chek the orientation of the onnetors on the Conversion Cable before onneting the Conversion Cable. Do not fore a onnetor if it does not onnet smoothly. Using exessive fore may damage the onnetor. 25.Do not plae heavy objet on the Conversion Cable, bend the able past its natural bending radius, or pull on the able with undue fore. 26.Do not onnet or disonnet the Conversion Cable while ommuniations are in progress. Produt faults or malfuntion may our. 27.ake sure that the Conversion Cable's metal omponents are not touhing the external power terminals. 28.Do not touh the onnetors on the Conversion Cable with wet hands. Eletrial shok may result. 29.Before using infrared ommuniations, orretly attah the enlosed ounting Adapter to the able for the Support Software. When onneting the infrared port on the able to the Support Software into the Adapter, insert the onnetor to the speified line. Communiations may not be possible if the onnetor is not onneted properly. Preautions for Corret Use Servie Life. Use the produt within the following temperature and humidity ranges: Temperature: to 55 C (with no iing or ondensation) Humidity: 25% to 85% If the produt is installed inside a ontrol board, the ambient temperature must be kept to under 55 C, inluding the temperature around the produt. 2. The servie life of eletroni devies like Temperature Controllers is determined not only by the number of times the relay is swithed but also by the servie life of internal eletroni omponents. Component servie life is affeted by the ambient temperature: the higher the temperature, the shorter the servie life and, the lower the temperature, the longer the servie life. Therefore, the servie life an be extended by lowering the temperature of the Temperature Controller. 3. When two or more Temperature Controllers are mounted horizontally lose to eah other or vertially next to one another, the internal temperature will inrease due to heat radiated by the Temperature Controllers and the servie life will derease. In suh a ase, use fored ooling by fans or other means of air ventilation to ool down the Temperature Controllers. When providing fored ooling, however, be areful not to ool down the terminals setions alone to avoid measurement errors. easurement Auray. When extending or onneting the thermoouple lead wire, be sure to use ompensating wires that math the thermoouple types. 2. When extending or onneting the lead wire of the platinum resistane thermometer, be sure to use wires that have low resistane and keep the resistane of the three lead wires the same. 3. ount the produt so that it is horizontally level. 4. If the measurement auray is low, hek to see if input shift has been set orretly. Waterproofing The degree of protetion is as shown below. Setions without any speifiation on their degree of protetion or those with IP@ are not waterproof. Front panel: IP66 Rear ase: IP2, Terminal setion: IP (E5CN-U: Front panel: IP5, rear ase: IP2, terminals: IP) Operating Preautions. It takes approximately two seonds for the outputs to turn from after the power supply is turned. Due onsideration must be given to this time when inorporating Temperature Controllers in a sequene iruit. 2. When using self-tuning, turn power for the load (e.g., heater) at the same time as or before supplying power to the Temperature Controller. If power is turned for the Temperature Controller before turning power for the load, self-tuning will not be performed properly and optimum ontrol will not be ahieved. 3. When starting operation after the Temperature Controller has warmed up, turn the power and then turn it again at the same time as turning power for the load. (Instead of turning the Temperature Controller and again, swithing from STOP mode to RUN mode an also be used.) 4. Avoid using the Controller in plaes near a radio, television set, or wireless installing. These devies an ause radio disturbanes whih adversely affet the performane of the Controller. Others. The disk that is inluded with the Conversion Cable is designed for a omputer CD-RO driver. Never attempt to play the disk in a general-purpose audio player. 2. Do not onnet or disonnet the Conversion Cable onnetor repeatedly over a short period of time. The omputer may malfuntion. 3. After onneting the Conversion Cable to the omputer, hek the CO port number before starting ommuniations. The omputer requires time to reognize the able onnetion. This delay does not indiate failure. 4. Do not onnet the Conversion Cable through a USB hub. Doing so may damage the Conversion Cable. 5. Do not use an extension able to extend the Conversion Cable length when onneting to the omputer. Doing so may damage the Conversion Cable. Advaned Digital Temperature Controller E5CN-H 9

20 ounting ounting to a Panel For waterproof mounting, waterproof paking must be installed on the Controller. Waterproofing is not possible when group mounting several Controllers. Waterproof paking is not neessary when there is no need for the waterproofing funtion. E5CN E53-COV7 Terminal Cover (Aessory) Adapter (Aessory) Order the P2CF- or P3GA- Soket separately. Preautions when Wiring Separate input leads and power lines in order to prevent external noise. Use wires with a gage of AWG24 (ross-setional area:.25 mm 2 ) to AWG4 (ross-setional area: 2.8 mm 2 ) twistedpair able (stripping length: 5 to 6 mm). Use rimp terminals when wiring the terminals. Tighten the terminal srews to a torque of.74 to.9 N m, however the terminal srews on the E5CN-U must be tightened to a torque of.5 N m. Use the following types of rimp terminals for 3.5 srews. 7.2 mm max. 7.2 mm max. Waterproof paking (Aessory) Panel E5CN E5CN-U For Front-mounting Soket (Panel mounting is also possible.. The Panel ounting Adapter is also inluded with the E5CN-U. There is no waterproof paking inluded with the E5CN-U. 2. Insert the E5CN/E5CN-U into the mounting hole in the panel. 3. Push the adapter from the terminals up to the panel, and temporarily fasten the E5CN/E5CN-U. 4. Tighten the two fastening srews on the adapter. Alternately tighten the two srews little by little to maintain a balane. Tighten the srews to a torque of.29 to.39 N m. ounting the Terminal Cover E5CN ake sure that the UP mark is faing up, and then attah the E53- COV7 Terminal Cover to the holes on the top and bottom of the Temperature Controller. Do not remove the terminal blok. Doing so will result in malfuntion or failure. Removing the Temperature Controller from the Case The Temperature Controller an be removed from the ase to perform maintenane without removing the terminal leads. This is possible for only the E5CN, E5AN, and E5EN, and not for the E5CN-U. Chek the speifiations of the ase and Temperature Controller before removing the Temperature Controller from the ase. E5CN Tool insertion hole Flat-blade srewdriver (Unit: mm) () (2) (3).4 2. (). Insert a flat-blade srewdriver into the two tool insertion holes (one on the top and one on the bottom) to release the hooks. 2. Insert the flat-blade srewdriver in the gap between the front panel and rear ase, and pull out the front panel slightly. Hold the top and bottom of the front panel and arefully pull it out toward you, without applying unneessary fore. 3. When inserting the body of the Temperature Controller into the ase, make sure the PCBs are parallel to eah other, make sure that the sealing rubber is in plae, and press the E5CN toward the rear ase into position. While pushing the E5CN into plae, push down on the hooks on the top and bottom surfaes of the rear ase so that the hooks are seurely loked in plae. Be sure that eletroni omponents do not ome into ontat with the ase. 2 Advaned Digital Temperature Controller E5CN-H