Specifications. S&C SpeedNet Radios

Transcription

1 S&C SpeedNet Radios Specifications Conditions of Sale STANDARD: The seller s standard conditions of sale set forth in Price Sheet 150 apply, except as modified under SPECIAL WARRANTY PROVISIONS on page 2. SPECIAL TO THIS PRODUCT: INCLUSIONS: S&C SpeedNet Radios provide high-speed, long-range, peer-to-peer data communication for fixed pointto-point nodes up to 25 miles apart. They feature: Unlicensed 902- to 928-MHz IMS band with regional support for North America, Brazil, and New Zealand 51 channels with 500-kHz bandwidth in North America Frequency Hopping Spread Spectrum (FHSS) 4-Gaussian Frequency-Shift Keying (4-GFSK) Modulation Fast data transmission rates up to 650 kbps Message latency is 10.5 ms/per link, for a 300 byte DNP packet payload Frequency hop time, averaging 10 ms User-selectable transmit power: +30, +25, +20, or +10 dbm, default is +30 dbm -100 dbm sensitivity (at 10-5 Bit Error Rate) Use of 16-bit Cyclic Redundancy Check, Automatic Repeat request, and Reed-Solomon Forward Error Correction for error detection and correction Serial and Ethernet data input supporting: IPv4, TCP, UDP, ICMP, SNMPv3 Use of the Enhanced Ad-hoc On-demand Distance Vector (AODV) network protocol Secure 128-bit AES data encryption with user-defined keysets created using the supplied Keygen tool MAC address filtering Star network or Mesh network using IP addresses Use of the Carrier Sense Multiple Access (CSMA) wireless protocol Assignable message priority for example, configuring S&C IntelliRupter PulseCloser Fault Interrupter operation messages to transmit first Simple Network Management Protocol version 3 (SNMPv3) and a supplied Microsoft Windows-based SpeedNet Client tool to set parameters, monitor status, and automate data collection Multi-level administrative passwords Over-the-air configuration and software updates Single network gateway Availability of received signal strength indication statistics in real time and from data logs Battery back-up with remote battery testing on repeater and gateway models A highly adaptive IP-addressable mesh network of Speed- Net Radios is easy to set up and maintain. SpeedNet Radios can communicate through each other to establish new message paths when a node is lost, providing excellent signal-loss tolerance and network reliability. SpeedNet Radios provide highly secure transmissions, too. Their frequency-hopping spread-spectrum signals are inherently difficult to intercept and jam. IP/MAC address filtering prevents unauthorized users from accessing the network. And 128-bit AES encryption ensures that critical data are not compromised. SpeedNet Radios are offered in five versions: SpeedNet Radio for installation in a user-furnished enclosure SpeedNet Streetlight-Mounted Repeater Radio in a cast-aluminum weatherproof enclosure that mounts on a streetlight arm (Extends communication range and expands network area.) SpeedNet Extension Arm-Mounted Repeater Radio in a cast-aluminum weatherproof enclosure with an extension arm that mounts on a utility pole (Extends communication range and expands network area.) SpeedNet Utility-Pole-Mounted Repeater Radio in a padlockable plastic weatherproof enclosure that mounts directly on a utility pole (Extends communication range and expands network area.) SpeedGate Radio Interface System in a padlockable plastic weatherproof enclosure that mounts directly on a utility pole (Includes provision for a gateway communication device, permitting data exchange with a different communication system.) August 21, 2017 S&C Electric Company , all rights reserved Specification Bulletin

2 Conditions of Sale Continued Device Compatibility SpeedNet Radios cannot communicate directly with other types of radios because of differences in frequency selection, spread-spectrum frequency-hopping patterns, channel use, and network management algorithms. A SpeedGate Repeater Radio, with an appropriate gateway communication device, is required in such instances. Antennas SpeedNet Radios are FCC approved for use only with the antenna/cable combinations offered in this specification bulletin. EXCLUSIONS: If the user s communication system also requires licensed radios, frequency selection and FCC license application are to be provided by others. SPECIAL WARRANTY PROVISIONS: The standard warranty contained in the seller s standard conditions of sale, as set forth in Price Sheet 150, applies to S&C SpeedNet Radios, except that the first paragraph of the said warranty is replaced by the following: (1) General: The seller warrants to the purchaser for a period of two years from the date of shipment that the equipment delivered will be of the kind and quality specified in the contract description and will be free of defects of workmanship and material. Should any failure to conform to this warranty appear under proper and normal use within two years after the date of shipment, the seller agrees, upon prompt notification thereof and confirmation that the equipment has been stored, installed, operated, inspected, and maintained in accordance with the recommendations of the seller and standard industry practice, to correct the nonconformity either by repairing any damaged or defective parts of the equipment or (at the seller s option) by shipment of necessary replacement parts. The above special warranty does not apply to gateway communication devices applied with SpeedNet Radios. END USER LICENSE AGREEMENT: The end user is granted a nontransferable, non-sublicensable, nonexclusive license to use the software furnished with SpeedNet Radios only upon acceptance of all the terms and conditions of the seller s end user license agreement set forth in Price Sheet 155. How To Order Select catalog numbers for the radios and accessories, and catalog number suffixes for the desired options. 2 S&C Specification Bulletin

3 Table 1. SpeedNet Radios and SpeedGate Radio Interface System Item SpeedNet Radio1 for mounting in user-furnished enclosure. Includes a 4-foot (121.9-cm) power cord for connection to user-furnished 12-Vdc power source SpeedNet Streetlight-Mounted Repeater Radio2 in a cast-aluminum weatherproof enclosure. Includes an adjustable galvanizedsteel mounting bracket for attachment to a streetlight arm or other circular cross-section, a battery charger, a battery providing 8-hour minimum backup on loss of ac control power3, a 3-foot (91.4-cm) streetlight photocell adapter power cable, and an omnidirectional 5-dBd whip antenna on bottom of enclosure With a 900-MHz band-pass filter With a 10-foot (304.8-cm) unterminated cable for connection to a user-furnished Vac, 50/60-Hz power source6, instead of a streetlight photocell adapter power cable With a 10-foot (304.8-cm) unterminated cable for connection to a user-furnished Vac, 50/60-Hz power source6, instead of a streetlight photocell adapter power cable, and a 900-MHz band-pass filter SpeedNet Extension Arm-Mounted Repeater Radio2 in a cast-aluminum weatherproof enclosure. Includes a galvanized steel extension arm for attachment to a utility pole, a battery charger, a battery providing 8-hour minimum backup on loss of ac control power3, a 10-foot (304.8-cm) unterminated cable for connection to a user-furnished Vac, 50/60-Hz power source6, and an omnidirectional 5-dBd whip antenna on bottom of enclosure With 900-MHz band-pass filter SpeedNet Utility-Pole-Mounted Repeater Radio3 in a padlockable plastic weatherproof enclosure. Includes an aluminum bracket for direct attachment to utility pole, a battery charger, a battery providing 8-hour minimum backup on loss of ac control power3, a connector for a user-furnished Vac, 50/60-Hz power source6, and an omnidirectional 5-dBd whip antenna on top of door With a 900-MHz band-pass filter With a PolyPhaser surge suppressor on bottom of enclosure, for a remote antenna With a PolyPhaser surge suppressor on bottom of enclosure for a remote antenna and a 900-MHz band-pass filter SpeedGate Radio Interface System4 in a padlockable weatherproof plastic enclosure. Includes an aluminum bracket for direct attachment to a utility pole, a battery charger, a battery providing 8-hour minimum backup on loss of ac control power3, a connector for a user-furnished Vac, 50/60-Hz power source Select accessories from Table 3 on page 5. 2 Select accessories from Table 4 on page 6. 3 Assuming typical IntelliTeam II Automatic Restoration System communications traffic and an enclosure temperature of 77 F (25 C). 4 Select accessories from Table 5 on page 6. 5 Select gateway communication device from the Table 2 on page 4. 6 Power cable must be ordered separately from Table 4 on page 6 7 Power cable must be ordered separately from Table 5 on page 6. S&C Specification Bulletin

4 Table 2. SpeedGate Options List Item1 Gateway Communication Devices for SpeedGate Radio Interface System (furnished by S&C) Approximate Battery Carryover Time, Hours2 Suffix to Be Added to SpeedGate Radio UtiliNet Series IV Radio 9 -XR67 MDS Transnet 900 Transceiver with Diagnostics 8 -XR19 Single-Mode Dymec 5843SHRT Fiber-Optic Modem 13 -XR44 Multi-Mode Dymec 5843HRT Fiber-Optic Modem 18 -XR45 Telemetric DNP-RTMII-GSM Transceiver 9 -XR161 SpeedNet Cell Edge Gateway4 MDS SD9 Remote Radio Ready for Gateway Communication Devices for SpeedGate Radio Interface System (furnished by customer) SpeedNet Radio -R88 UtiliNet Series 3000 or Series IV Radio 9 -XR66 MDS 9810 Radio 9 -XR02 MDS 9710A Radio 8 -XR03 MDS Transnet 900 Transceiver 8 -XR07 Single-Mode Dymec 5843SHRT Fiber-Optic Modem 13 -XR42 Multi-Mode Dymec 5843HRT Fiber-Optic Modem 18 -XR43 -XR322 Telemetric DNP-RTMII-GSM Transceiver 9 -XR160 MDS SD9 Remote Radio SpeedNet Radio Antenna Connector N-Type Connector, Top Mounted, for Local Antenna -S1 N-Type Connector, Bottom Mounted, for Local Antenna -S2 Poly-Phaser Surge Suppressor, N-Type Connector, Bottom Mounted, for Remote Antenna Installation3 -S3 Gateway Radio Antenna Connector Poly-Phaser Surge Suppressor, N-Type Connector, Bottom Mounted, for Remote Antenna Installation3 -XR217 -XS3 1 Contact your local S&C Sales Office regarding other communication devices. 2 Battery carryover time is dependent on transmission polling rate, ambient temperature, and radio power consumption. Time indicated assumes typical IntelliTeam II Automatic Restoration System communications traffic and an enclosure temperature of 77 F (25 C). 3 Select Remote Antenna Kit from Table 5 on page 6. Two Remote Antenna Kits are required if two remote antennas are specified. 4 Please see Specification Bulletin for SpeedNet Cell Edge Gateway antenna options. Specify the appropriate catalog number suffix based on the frequency band range and application for the radio, from the following table. For example, for a 928- to 960-MHz MDS SD9 Radio for Ethernet and serial application, specify catalog number suffix -XR216CL. Frequency Band Range, MHz 820 to 870 Application Suffix to be Added to -XR216AK 928 to 960 -XR216CK 928 to 960, 50-kHz Channel -XR216DK 880 to 915 -XR216EK 880 to 915, 50-kHz Channel Serial -XR216FK 850 to 860 / 926 to 936, Transmit Low 850 to 860 / 926 to 936, Transmit High 820 to 870 -XR216GK -XR216HK -XR216AL 928 to 960 -XR216CL 928 to 960, 50-kHz Channel -XR216DL 880 to 915 Ethernet and -XR216EL 880 to 915, 50-kHz Channel Serial -XR216FL 850 to 860 / 926 to 936, Transmit Low 850 to 860 / 926 to 936, Transmit High -XR216GL -XR216HL Frequency Band Range, MHz 820 to 870 Application Suffix to be Added to -XR216AM 928 to 960 -XR216CM 928 to 960, 50-kHz Channel -XR216DM 880 to 915 -XR216EM 880 to 915, 50-kHz Channel 9710 Emulation -XR216FM 850 to 860 / 926 to 936, Transmit Low 850 to 860 / 926 to 936, Transmit High -XR216GM -XR216HM TABLE CONTINUED 4 S&C Specification Bulletin

5 Table 2. SpeedGate Options List Continued SpeedNet Local Antenna Item1 Suffix to Be Added to SpeedGate Radio 900-MHz 5-dB Gain Antenna, N-Type Male Connector T2 900-MHz Mobile Mark Antenna RM3-900/1900 Dual-Band Cellular Antenna T7 Band-Pass Filters 900-MHz Band-Pass Filter for SpeedNet Radio F1 900-MHz Band-Pass Filter for UtiliNet Radio XF2 Table 3. SpeedNet Radio Accessories Item 12-Vdc Power Cord 4-foot ( cm), with connector on one end and bare wires on the other end Vac Power Adapter supplies 12 Vdc to radio Antenna Cable 22 inch (55.9 cm), with SMA male to N-Type male connectors and bulkhead connector External 900-MHz Band-Pass Filter Field Retrofit Kit Omnidirectional 5-dBd Whip Antenna mounts on bulkhead connector Remote Antenna Kit includes omnidirectional fiberglass antenna, pole-mounted single-antenna arm Remote Antenna Kit includes unidirectional Yagi antenna, pole-mounted single-antenna arm With 30-foot (76.2-cm) coaxial cable with N-Type male With 50-foot (127-cm) coaxial cable with N-Type male With 30-foot (76.2-cm) coaxial cable with N-Type male (Customer to provide inch (34.9 mm) OD pipe for antenna) With 50-foot (127-cm) coaxial cable with N-Type male (Customer to provide inch (34.9 mm) OD pipe for antenna) ½-inch (12.7-mm)Wave Dipole Antenna, Rubber Duck Style, 90 Degree Adjustable Knuckle, SMA Male, MHz, 2.3 dbi Max Gain Way 900 MHz Signal Splitter, N-Female Connector Way 900 MHz Signal Splitter, N-Female Connector Flat-Panel Directional Antenna, MHz, Dimensions 15.4 inches (391.2 mm) 15.4 inches (391.2 mm) 1.7 inches (43.2 mm) Type-400 ⅜-inch (9.5-mm) Coaxial Cable, sold by the foot Retrofit Kit for Replacing a UtiliNet Series II or Series 3000 Radio with a SpeedNet Radio. Includes mounting bracket, power- and antenna-adapter cables Retrofit Kit for Replacing a UtiliNet Series 3000 Radio with a SpeedNet Radio. No adapter cables included, connectors are the same for both radios Programming Cable 7-foot (213.4 cm), for Ethernet connection S&C Specification Bulletin

6 Table 4. SpeedNet Repeater Radio Accessories Ac Power Cable for Streetlight-Mounted and Extension- Arm-Mounted Repeater Radios Ac Power Cable for Utility-Pole-Mounted Repeater Radio 1 Other cord lengths are available. Item With 10-foot (304.8 cm) unterminated #10 wire With 6-foot (182.9 cm) with plug for ac outlet With 10-foot (304.8 cm)unterminated #10 wire With 6-foot (182.9 cm) cable with plug for ac outlet Streetlight Photocell Adapter includes 3-foot (91.44 cm) cord External 900-MHz Band-Pass Filter Kit Replacement Battery, 4.5 Ampere-Hour, 12 Vdc Replacement Omnidirectional 5-dBd Whip Antenna Remote Antenna Kit for SpeedNet Utility-Pole-Mounted Repeater Radio Includes omnidirectional fiberglass antenna, pole-mounted single-antenna arm With 30-foot (914.4 cm) coaxial cable with N-Type male With 50-foot (1524 cm) coaxial cable with N-Type male SpeedNet Repeater Battery and External Hardware Replacement Kit Includes Gasket SpeedNet External Hardware Replacement Kit Includes Gasket Programming Cable 7-foot (213.4 cm) for Ethernet connection Table 5. SpeedGate Radio Interface System Accessories Item Ac Power Cable 10-foot (304.8 cm) unterminated #10 wire Streetlight Photocell Adapter includes 12-foot (365.8 cm) cord MHz Band-Pass Filter Field-Retrofit Kit for SpeedNet Radio Replacement Battery, 4.5 Ampere-Hour, 12 Vdc Replacement Omnidirectional 5-dBd Whip Antenna Remote Antenna Kit includes omnidirectional fiberglass antenna, pole-mounted single-antenna arm Remote Antenna Kit includes unidirectional Yagi antenna, pole-mounted single-antenna arm Remote Dual-Antenna Kit includes omnidirectional fiberglass SpeedNet antenna, cellular antenna, pole-mounted dualantenna arm With 30-foot (914.4 cm) coaxial cable with N-Type male With 50-foot (1524 cm) coaxial cable with N-Type male With 30-foot (914.4 cm) coaxial cable with N-Type male (Customer to provide inch (34.9 mm) OD pipe for antenna) With 50-foot (1524 cm)coaxial cable with N-Type male (Customer to provide inch (34.9 mm) OD pipe for antenna) With two 30-foot (914.4 cm) coaxial cables with N-Type male With two 50-foot (1524 cm) coaxial cables with N-Type male Programming Cable 7 foot (213.4 cm), for Ethernet connection Other cord lengths are available. Table 6. Substation Communication Package Item Substation Communication Package. Includes a SpeedNet Radio, 110-Vac power supply, PolyPhasor Surge Suppressor, 6-dB substation antenna with integrated mounting bracket, 80-foot ( cm) antenna cable, and other associated cabling S&C Specification Bulletin

7 SpeedNet Radio Dimensions in inches (mm) 0.25 (6) 4.75 (121) 4.25 (108) 5.25 (127) 4.75 (121) 6.30 (160) 1.29 (33) S&C Specification Bulletin

8 SpeedNet Streetlight-Mounted Repeater Radio Dimensions in inches (mm) (284) (274) 4.75 (121) 9.57 (243) (330) (327) 8 S&C Specification Bulletin

9 SpeedNet Extension Arm-Mounted Repeater Radio Dimensions in inches (mm) 8.00 (203) (914) S&C Specification Bulletin

10 SpeedNet Utility-Pole-Mounted Repeater Radio Dimensions in inches (mm) 9.85 (250) (260) 2.50 (64) (508) (21) (330) (376) (457) 1.50 (38) (6) (14) (19) (127) (288) 10 S&C Specification Bulletin

11 SpeedGate Radio Interface System 5.00 (127) Dimensions in inches (mm) 1.81 (46) 0.83 (21) (610) (559) (424) (470) (14) 1.50 (38) (19) (6) (413) 9.85 (250) S&C Specification Bulletin

12 Power Connector on the SpeedNet Repeater Radios and SpeedGate Radio Interface System D C E B A The power cable connector has a jumper between pins D and E. When D and E are shorted the battery is connected, and the battery charger monitors and charges the battery. When the power cable is removed (D and E are open), the battery is disconnected so the radio will not discharge the battery before ac power is connected. A repeater radio or SpeedGate system is always operated with ac power connected, and battery backup is only used during a power outage. Pin Connection A Ac Hot B Ac Neutral C Not used D Disconnect Logic + E Disconnect Logic Connector on SpeedGate Radio. E A B D C Connector on SpeedNet Repeater Radios. 12 S&C Specification Bulletin