Vibration 10 Times in X,Y,Z IEC In Case of Continuous Vibration

Transcription

1 FEATURES LED Display to Monitor Running Conditions PhotoCoupler Insulated Snapin Installation Terminal BlockType 4bit (/6,84) or 6bit (/65,55) Resolution 4 or 8 Channels Voltage or DESCRIPTION PLCAIOCMAD Series CIMON s AnalogtoDigital (ADC) I/O Modules are offered in 4 or 8 analog channels, allowing for extreme flexibility in a number of different applications. The CM ADC module offers you a 4bit analog to digital converter with the option of upgrading to a 6bit analog to digital unit. The 6bit analog to digital converter has a much higher resolution and processes inputs at a much higher frequency. The CM analog modules are capable of reading both voltages and currents. Voltage inputs can range from 0 to +0 VDC and current values can range from 0 to 0 ma. One of the analog modules comes with both analog to digital conversion as well as digital to analog conversion on one unit. These modules are ideal for use with Anaheim Automation s Brushless Drivers, which utilizes a 05 VDC signal for speed control. With the CM analog units you can select different ranges to best fit your application needs. Item Specification Reference Op. Temp Operating Temperature 0 ~65 ºC St. Temp Storage Temperature 5~80 ºC Op. Hum Operating Humidity 5~95%RH, Not Condensed St. Hum Storage Humidity 5~95%RH, Not Condensed In Case of Intermittent Vibration GENERAL SPECIFICATIONS Frequency Vibration Acceleration Amplitude 0 f 57 Hz mm 57 f 50 Hz 9.8 m/s {G} Frequency Acceleration Amplitude 0 f 57 Hz 0.05 mm 4.8 m/s {0.5 g} 0 Times in X,Y,Z IEC6 Maximum Shock Acceleration: 47 m/s {5 g} Time: ms Pulse Wave: Half Since Wave Pulse ( Times in X,Y,Z) Shock Square Wave Impulse Noise,000 V KDT Standard ElectroStatic Discharge Voltage: 4 kv (Contact Discharge) IEC6 IEC0004 Radiated ElectroMagnetic Field 7 ~500 MHz, 0 V/m IEC6 IEC0004 Fast Transient Bust Noise Sweep In Case of Continuous Vibration 57 f 50 Hz Noise Power Module Digital I/O (4V or More) Digital I/O (Less than 4V) Analog I/O Comm Interface kv kv 0.5 kv IEC6 IEC00044 Environment No Corrosive Gas or Dust Altitude,000 m or less Pollution or less Cooling Natural Air Cooling 90 East Orangefair Ln. Anaheim, CA 980 Tel. (74) Fax. (74)

2 MODULE SPECIFICATIONS PLCAIOCMAD Series Item CMAD04V CMAD08V CMAD08I No. of Analog Outputs 4 Points 8 Points 8 Points 4 Points Analog (0~0 ma) (4~0 ma) 0~0 ma 4~0 ma Range of Analog Max. Resolution.5 uv Voltage 50 uv 65 uv.5 mv 0 ~ 0 ma.5 na 4 ~ 0 ma na Precision ±0.% (Full Scale) Conversion Rate 5 ms / Ch. Absolute Max. Voltage: ± VDC : ±5 ma CMAD04W Voltage 0 ~ ~ 8000 Max. Resolution 78. uv 6.5 uv 56. uv.5 uv 0~0 ma.5 na 4~0 ma 50 na 0 ~ 64,000 0 ~ 0,000 ±0.05% (Full Scale). ms / Ch. ± VDC Voltage: ± VDC : ±5 ma ±5 ma Between Terminal and PLC: PhotoCoupler Between Channels: None Insulation Occupied Points 6 Points Contact Terminal 8Point Terminal Block Internal (ma) Range of Analog +5V +5V 5V 5 ma 0 ma 0 ma Voltage : Channel V+ Pin V Pin CMAD04VI CMAD08I CMAD08V MODULE WIRING : Channel V+ Pin V Pin Action Connect 6 7 Connect 56 0 Connect Connect 4 90 East Orangefair Ln. Anaheim, CA 980 Make sure the polarity is correct before connecting the analog input to a terminal. AD04VI: Do not use terminals 4,8,,6,7 or 8. For voltage inputs, use the V+ terminals and COM terminal For current inputs, use the COM terminal, and connect the V+ terminals with the I+ terminals AD08I: Do not use terminals 7 and 8 AD08V: Do not use terminals 7 and 8 Tel. (74) Fax. (74)

3 PLCAIOCMAD Series MODULE DIMENSIONS I/O SIGNALS Direction (A/D CPU) Direction (CPU A/D) Signal Name Output Signal Name X0 A/D Module Read Y0 X Flag indicating A/Dconverted Y Not use X Flag indicating operation condition setup Y Requesting to set up operation condition X Flag indicating channel switched Y Requesting to switch channel X4 Flag indicating offset or gain calibration mode Y4 Requesting to calibrate offset or gain X5 Y5 Assigning offset or gain mode X6 Y6 X7 Y7 X8 Y8 X9 Y9 Not Used XA YA Not Used XB YB XC YC XD YD XE YE Requesting to reset max. value and min. value XF Flag indicating error in A/D module YF Requesting to clear error 90 East Orangefair Ln. Anaheim, CA 980 Tel. (74) Fax. (74)

4 USER PROGRAM MEMORY DEVICES PLCAIOCMAD Series Offset Hex Dec Description R/W 0H 0 Enabling/Disabling to A/Dconvert Setup R/W H Average Time & Number of Times Ch. R/W H Average Time & Number of Times Ch. R/W H Average Time & Number of Times Ch. R/W 4H 4 Average Time & Number of Times Ch. 4 R/W 5H 5 Average Time & Number of Times Ch. 5 R/W 6H 6 Average Time & Number of Times Ch. 6 R/W 7H 7 Average Time & Number of Times Ch. 7 R/W 8H 8 Average Time & Number of Times Ch. 8 R/W 9H 9 Assigning Averaging Process R/W AH 0 Flag Indicating A/Dconverted R BH Value of Ch. R CH Value of Ch. R DH Value of Ch. R EH 4 Value of Ch. 4 R FH 5 Value of Ch. 5 R 0H 6 Value of Ch. 6 R H 7 Value of Ch. 7 R H 8 Value of Ch. 8 R H 9 Error Code R 4H 0 Set Range (Ch. ~ Ch. 4) R/W 5H Set Range (Ch. 5 ~ Ch. 8) R/W 6H Channel to Calibrate Offset R/W 7H Channel to Calibrate Gain R/W 8H 4 Setting Up R/W 9H 5 AH 6 BH 7 Not Used CH 8 DH 9 EH 0 Max. Value of Ch. R FH Min. Value of Ch. R 0H Max. Value of Ch. R H Min. Value of Ch. R H 4 Max. Value of Ch. R H 5 Min. Value of Ch. R 4H 6 Max. Value of Ch. 4 R 5H 7 Min. Value of Ch. 4 R 6H 8 Max. Value of Ch. 5 R 7H 9 Min. Value of Ch. 5 R 8H 40 Max. Value of Ch. 6 R 9H 4 Min. Value of Ch. 6 R AH 4 Max. Value of Ch. 7 R BH 4 Min. Value of Ch. 7 R CH 44 Max. Value of Ch. 8 R DH 45 Min. Value of Ch. 8 R 90 East Orangefair Ln. Anaheim, CA 980 Tel. (74) Fax. (74)

5 PLCAIOCMAD Series In the case of an error, the following error codes are stored in buffer memory location, offset 9. The LED will begin to blink at an interval of 0. seconds. You can also view the error code through the AD Module dialog box: Tool Special Module Setup AD Module Status ERROR CODES To clear an error code, select the Error Code Reset button in the AD Card Setup dialog box. *Error Codes pertain to the AD Module Error Code Descirption Range of the analog input is setup wrong Setup for current in the AD08V or voltage for the AD08I Average process time is out of range Number of average process times is out of range 4 Offset value is greater than a gain value 0 System error (A/S required) 49 Offset channels and gain channels are calibrated at the same time SAFETY PRECAUTIONS Note: The following safety precautions should be considered during the installation and operation of the PLCAIOCMAD series module. Use proper cables for DC and AC voltages to prevent influence of surge or induction noise. Select a cable considering ambient temperature/allowable current. 8 AWG or more is recommended. Wiring located close to a heatgenerating device or material, and/or direct contact with oil for long periods may cause a short circuit, breakdown, or malfunction. Operating near a highvoltage line or power line may cause a malfunction or breakdown due to an induction jam. Design is recommended to be wired 00mm from a highvoltage line. 90 East Orangefair Ln. Anaheim, CA 980 Tel. (74) Fax. (74)