Class Sealing Fully sealed Contact configuration Rated coil voltage Model Basic Type SPDT 4.5 VDC G6Y-1 5 VDC 9 VDC 12 VDC 24 VDC

Size: px

Start display at page:

Download "Class Sealing Fully sealed Contact configuration Rated coil voltage Model Basic Type SPDT 4.5 VDC G6Y-1 5 VDC 9 VDC 12 VDC 24 VDC"

Holly Lawson
5 years ago
Views:

Switching Structure Based on the Micro Strip Line is Used to Combine High Performance and Costeffectiveness ROHS compliant. Isolation characteristics of 65 db or better at 900 MHz.

1 Switching Structure Based on the Micro Strip Line is Used to Combine High Performance and Costeffectiveness ROHS compliant. Isolation characteristics of 65 db or better at 900 MHz. Effective insertion loss characteristics of 0.2 db or better at 900 MHz (half the loss of earlier models). Fully sealed construction provides excellent environmental resistance. Improved shock-resistance (double the resistance of earlier models). Ordering Information Class Sealing Fully sealed Contact configuration Rated coil voltage Model Basic Type SPDT 4.5 VDC G6Y-1 5 VDC 9 VDC 12 VDC 24 VDC Model Number Legend G6Y-(( VDC Number of contact poles 1: Single pole (SPDT contact) 2. Rated Coil Voltage 4.5, 5, 9, 12, 24 VDC Basic Specifications Contact Mechanism: Double-braking bifurcated contact Contact Material: Gold alloy Sealing: Fully sealed Terminal Configuration: Printed circuit board terminal configuration Application Examples Signal Switching in Various Communications Equipment Wired Communications: Cable TV, captain systems, and video response systems (VRS) Wireless Communications: Transceivers, ham radio, car telephones, high-level TV, fax machines, satellite broadcasting, text multiplex broadcasting, and pay TV Public Equipment: VCRs, TVs, video disk players, and TV games Industrial Equipment: Measuring equipment, test equipment, and multiplex transmission devices 252

2 Ratings Operational Coil Item Rated Coil Operating Release Max. allowed Power Rated voltage current resistance voltage voltage voltage consumption Class (V) (ma) (Ω) (V) (V) (V) (mw) Basic Type DC % max. 10% min. 1% of Approx rated voltage at 23 C ,880 Note: The rated current and coil resistance are measured at a coil temperature of 23 C with a tolerance of ±10%. The operating characteristics are measured at a coil temperature of 23 C. The Max. allowed voltage is the maximum voltage that can be applied to the relay coil. It is not the maximum voltage that can be applied continuously. Signal Relays Contact Ratings Load Rated voltage Contact material Rated carry current Max. switching voltage Max. switching current Max. switching power (reference value) Resistive load 0.01 A at VAC 0.01 A at VDC 900 MHz, 1 W (see note) Au 0.5 A VAC VDC 0.5 A AC10VA DC10W Note: This value is for a load with V.SWR x 1.2. High-frequency Characteristics Item 2 MHz 900 MHz 2.5 GHz Isolation 80 db min. 65 db min. db min. Insertion loss 0.5 db max. 0.5 db max. V.SWR 1.5 max. 1.5 max. Max. carry 10 W power Max. switching 10 W (see note 3) power Note: 1. The impedance of the measuring system is Ω. 2. The table above shows preliminary values. 3. This value is for a load with V.SWR x 1.2 Characteristics Contact resistance (see note 1) Operating time Release time Insulation resistance (see note 2) Dielectric strength Vibration resistance 100 mω max. 10 ms max. (approx. 5 ms) 5 ms max. (approx. 1 ms) 100 mω min. Shock resistance Destruction: 1,000 m/s 2 Malfunction: 0 m/s 2 Endurance Failure rate (reference 10 mvdc, 10 µa value (see note 3)) Ambient temperature 1,000 VAC, /60 Hz for 1 min between coil and contacts 0 VAC, /60 Hz for 1 min between contacts of same polarity 0 VAC, /60 Hz for 1 min between coil and ground and between contacts and ground Destruction: 10 Hz to 55 to 10 Hz, 0.75-mm single amplitude (1.5 mm double amplitude) Malfunction: 10 Hz to 55 to 10 Hz, 0.75-mm single amplitude (1.5 mm double amplitude) Mechanical: 1,000,000 operations min. (at 1,800 operations/hr) Electrical: 0,000 operations min. (under rated load at 1,800 operations/hr) Operating: - C to 70 C (with no icing) Ambient humidity Operating: 5% to 85% Weight Approx. 5 g Note: The table above shows preliminary values. 1. Measurement Conditions: 5 VDC, 100 ma, voltage drop method 2. Measurement Conditions: Measured at the same points as the dielectric strength using a 0-VDC ohmmeter. 3. This value is for a switching frequency of 120 operations/minute. 253

3 Engineering Data Ambient Temperature vs. Maximum Coil Voltage Maximum coil voltage (%) (1) (1) Ambient temperature ( C) Note: The maximum coil voltage refers to the maximum value in a varying range of operating power voltage, not a continuous voltage. Malfunctioning Shock X Z N.O. contact 1,000 N.C. contact Y' 2 Units: m/s X X' Y Z Z' Y' Shock direction Quantity Tested: 10 Units Test Method: Shock was applied 3 times in each direction with and with out excitation and the level at which the shock caused mal function was measured. Rating: 0 m/s Y , Z' X' Contact Reliability Test (See Note) Sample: G6Y-1, 12 VDC Quantity: 20 Units Conditions: Resistive load: 10 mvdc 0.01 ma Switching frequency: 120 times/minute Contact resistance N.O. contact N.C. contact 4 Number of operations ( 10 ) Note: Ambient temperature of 23 C HP8753D Network Analyzer -Ω Terminator G6Y-1 Terminals which were not being measured were terminated with Ω. Note: The high-frequency characteristics data were measured using a dedicated circuit board and actual values will vary depending on the usage conditions. Check the characteristics of the actual equipment being used. Isolation (db) Isolation Characteristics (Average Values) (See notes 1 and 2.) Insertion loss (db) Insertion Loss Characteristics (Average Values) (See notes 1 and 2.) V.SWR, Return Loss Characteristics (Average Values) (See notes 1 and 2.) ,000 1,0 2,000 2, ,000 1,0 2,000 2, ,000 1,0 2,000 2,0 Frequency (MHz) Frequency (MHz) Frequency (MHz) Return loss (db) Return loss V.SWR V.SWR 254

Quantity Operating/Release Time Distribution (See Note) Sample: G6Y-1 Quantity: Units Operating time Release time Bounce Time Distribution (See Note) Quantity Subject: G6Y-1 Quantity: Units Operating

4 Quantity Operating/Release Time Distribution (See Note) Sample: G6Y-1 Quantity: Units Operating time Release time Bounce Time Distribution (See Note) Quantity Subject: G6Y-1 Quantity: Units Operating bounce time Release bounce time Signal Relays Time (ms) Time (ms) Note: Ambient temperature: 23 C Dimensions Note: All units are in millimeters unless otherwise indicated. G6Y max. (20.5)* 11.7 max. (11.5)* PCB Dimensions (Bottom View) Tolerances: ±0.1 mm. Six, 1.2-dia. holes Three, 0.8-dia. holes (1.83) Terminal Arrangement/ Internal Connections (Bottom View) 9.2 max. (9.0)* (2.05) * Average value 3 (2.05) (2.63) (2.63) (Holes for the coil terminals may also be 1.0.) (There is no polarity to the coil.) Note: The shaded and unshaded parts indicate the product's directional marks. 255

5 Micro Strip impedance ( Ω ) Correct Use Airtightness when cleaning will last 1 minute at 70 C. Complete cleaning within these conditions. MICRO STRIP LINE DESIGN It is advantageous to use the Micro Strip Line in high frequency transmission circuits because a low-loss transmission can be constructed with this method. By etching the dielectric base which has copper foil attached to both sides, the Micro Strip Line will have a concentrated electric field between the lines and ground as shown in the following diagram. Ground pattern The characteristic impedance of the lines ZO is determined by the kind of base (dielectric constant), the base s thickness, and the width of the lines, as expressed in the following equation. ZO = εr Lines with impedance Z W H Dielectric base (dielectric constant: εr) H πw 1+In πw H W: Line width : Effective dielectric constant H: Dielectric base thickness The copper foil thickness must be less than H. The following graph shows this relationship. Dielectric constant (εr) For example, when creating Ω lines using a glass epoxy base with a thickness of 1.6 mm, the above graph will yield a w/h ratio of 1.7 for a dielectric constant of 4.8. Since the base thickness is 1.6 mm, the width will be h mm. The thickness of the copper foil t is ignored in this design method, but it must be considered because large errors will occur in extreme cases such as a foil thickness of t w. Furthermore, with the Micro Strip Line design, the lines are too short for the G6Y s intended frequency bandwidths, so we can ignore conductive losses and the line s attenuation constant. The spacing of the Strip Lines and ground pattern should be comparable to the width of the Strip Lines. Design the pattern with the shortest possible distances. Excessive distances will adversely effect the high-frequency characteristics. Spread the ground patterns as widely as possible so that potential differences are unlikely to develop between the ground patterns. To avoid potential short-circuits, do not place the pattern s leads near the point where the bottom of the Relay attaches to the board. BENDING THE MICRO STRIP LINE Strip Line with impedance Z Elbow When the lines must curve, an elbow can be used as shown in the diagram. A distance (D) between the lines of approximately twice the line width is sufficient. Clip the corners. 45 C Micro Strip (w/h) 256

EXAMPLES OF MOUNTING DESIGNS Since this example emphasizes reducing mounting costs, expensive mounting methods such as through-hole boards are not shown.

6 EXAMPLES OF MOUNTING DESIGNS Since this example emphasizes reducing mounting costs, expensive mounting methods such as through-hole boards are not shown. If such methods are to be used, the characteristics must be studied carefully using the actual board configuration. Using a Double-sided Paper Epoxy Board When double-sided paper epoxy boards are used, the dielectric constant will be approximately the same as that of glass epoxy boards ( = 4.8). The width of the Strip Lines for a board with t=1.6 mm is 2.7 mm for Ω and 1.3 mm for 75 Ω. For a board with t=1.0 mm the width is 1.7 mm for Ω and 0.8 mm for 75 Ω. The following diagram shows an example pattern and the Micro Strip Lines connected to the contact terminals are formed with pattern widths derived from the description above. The width between the Micro Strip Lines and ground patterns are comparable to the Micro Strip Line width. There are jumpers between the upper and lower patterns at the points marked with Xs in the diagram. Improved characteristics can be obtained with more jumper locations. This method yields isolation characteristics of 65 db to 75 db at 0 MHz and db at 900 MHz. At this point in the diagram the component side is the entire ground pattern side, but set aside approximately 2.0 mm 2.0 mm of the pattern for the contact terminals and coil terminals. Strip Line With this method a metal plate is placed between the Relay and base and connected to the pattern, as shown in the above diagram. The important point here is that 3 locations (the G6Y s ground terminal, the metal plate s bent tabs (A), and the ground pattern) are soldered together at the same time. This method combines an inexpensive single-sided board and inexpensive metal plate to yield the same characteristics as a double-sided board and good characteristics are obtained by grounding the G6Y s ground terminal and metal plate in the same place. The metal plate must be attached to the base as described here. From this point, the methods used for Strip Line design are the same as for the double-sided board. Mounting Precautions Be sure to securely attach the Relay s base surface to the board during installation. The isolation characteristics will be affected if the Relay lifts off the board. As shown in the enlarged illustration of the cross-section of part A, the G6Y is designed to ensure better high-frequency characteristics if the stand-off part of the G6Y is in contact with the ground pattern of the PCB. Therefore, the ground terminal and stand-off part are electrically connected internally. Should the through hole electrically connected to the contact terminal come in contact with the stand-off part, the contact will be short-circuited with the ground, which may cause an accident. As a preventive measure, keep at least a distance of 0.3 mm between the stand-off part and the through hole or land. For example, if the terminal hole on the PCB is 1 mm in diameter and the length B shown in the illustration is 1.4 mm, a distance of 0.3 mm or more will be provided between the through hole and stand-off part. Signal Relays G6Y PCB Mounting Coil Using a Single-sided Board When a single-sided board is used, isolation characteristics of only 60 db to 70 db at 200 MHz can be obtained. When high frequency bands are to be used with a single-sided board, a metal plate can be placed between the base and Relay and connected to the ground pattern. Cross-section of Part A Part A Metal plate Stand-off part Ground pattern G6Y Ground terminals Metal plate Printed circuit board Through Contact hole terminal Ground terminal Ground terminal Pattern 257

Classification Contact form Contact type Contact material Enclosure Rating Model Standard DPDT Bifurcated crossbar Ag (Au alloy) Fully sealed G5V-2

Classification Contact form Contact type Contact material Enclosure Rating Model Standard DPDT Bifurcated crossbar Ag (Au alloy) Fully sealed G5V-2 Miniature Relay for Signal Circuits ROHS compliant. Wide switching power of 10 µa to 2 A. High dielectric strength coil-contacts:1,000 VAC; open contacts: 750 VAC. Conforms to FCC Part 68 requirements.