CERTIFICATE OF ACCREDITATION

Transcription

1 CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, This is to certify that Micro Precision Calibration, Inc Santa Teresa Blvd San Jose, CA has been assessed by ANAB and meets the requirements of international standard ISO/IEC 17025:2017 and national standards ANSI/NCSL Z (R2002) AND ANSI/NCSL Z (R2013) while demonstrating technical competence in the field of CALIBRATION Refer to the accompanying Scope of Accreditation for information regarding the types of calibrations to which this accreditation applies. AC Certificate Number Certificate Valid: 10/15/ /31/2020 Version No. 004 Issued: 10/15/2018 This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2017. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated April 2017).

2 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2017, ANSI/NCSL Z (R2002) AND ANSI/NCSL Z (R2013) Micro Precision Calibration, Inc Santa Teresa Blvd. San Jose, CA, Norma Vazquez Phone: CALIBRATION Valid to: October 31, 2020 Certificate Number: AC Chemical Quantities Conductivity µs 99 µs µs 0.43 µs 2.1 µs 2.8 µs Standard Conductivity Solutions ph 1 (4, 7, 10) ph 0.05 ph Standard ph Solutions Electrical DC/Low Frequency DC Voltage 1 - Source DC Voltage 1 - Measure DC Voltage 1 - Measure High Voltage (0 to 220) mv 220 mv to 2.2 V (2.2 to 22) V (22 to 220) V 220 V to 1.1 kv (0 to 100) mv 100 mv to 1V (1 to 10) V (10 to 100) V 100 V to 1 kv 9.8 µv/v µv 11 µv/v + 1 µv 8.3 µv/v µv 8.3 µv/v + 80 µv 8.8 µv/v mv 18 µv/v + 3 µv 10 µv/v µv 10 µv/v µv 9 µv/v + 30 µv 10 µv/v mv (1 to 60) kv 2 mv/v Fluke 5700A Multiproduct Calibrator Agilent 3458A Multimeter Ross VD-60 Voltage Divider Page 1 of 14

3 Electrical DC/Low Frequency DC Current 1 - Source DC Current 1 Measure Resistance 1 - Source Fixed Points Up to 220 µa 220 µa to 2.2 ma (2.2 to 22) ma (22 to 220) ma 220 ma to 2.2 A (2.2 to 11) A 80 µa/a + 8 na 67 µa/a + 8 na 68 µ A/A + 80 na 73 µa/a µa 74 µa/a + 25 µa 85 µa/a + 25 µa (1 to 1 000) A 3.7 ma/a Up to 100 µa 100 µa to 10 ma (10 to 100) ma 100 ma to 1 A 12 µa/a ma 13 µa/a + 5 µa 16 µa/a + 5 µa 97 µa/a + 10 µa Fluke 5720A Opt 03 Multiproduct Calibrator Fluke 5500A Multiproduct Calibrator with 50 turn Coil Agilent 3458A Multimeter (1 to 10) A 3.6 ma/a + 2 ma Fluke 289 Multimeter (10 to 550) A 20 ma/a + 0.4A Current Clamp 1.9 Ω 10 Ω 19 Ω 100 Ω 190 Ω 1 kω 1.9 kω 10 kω 19 kω 100 kω 190 kω 1 MΩ 1.9 MΩ 10 MΩ 19 MΩ 100 MΩ 55 µω/ω 26 µω/ω 15 µω/ω 14 µω/ω 15 µω/ω 23 µω/ω 14 µω/ω 12 µω/ω 14 µω/ω 14 µω/ω 15 µω/ω 13 µω/ω 16 µω/ω 18 µω/ω 44 µω/ω 0.1 mω/ω Fluke 5700A Multiproduct Calibrator Page 2 of 14

4 Electrical DC/Low Frequency Resistance 1 - Measure AC Voltage 1 - Source (0 to 10) Ω (10 to 100) Ω 100 Ω to 1 kω (1 to 10) kω (10 to 100) kω 100 k Ω to 1 MΩ (1 to 10) MΩ (10 to 100) MΩ 1 GΩ (22 to 220) mv (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 khz (100 to 300) khz (300 to 500) khz 500 khz to 1 MHz 220 mv to 2.2 V (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 khz (100 to 300) khz (300 to 500) khz 500 khz to 1 MHz (2.2 to 22) V (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 khz (100 to 300) khz (300 to 500) khz 500 khz to 1 MHz 28 µω/ω 17 µω/ω 10 µω/ω 10 µω/ω 15 µω/ω 25 µω/ω 71 µω/ω 0.6 mω/ω 0.7 mω/ω 0.55 mv/v + 13 μv 0.21 mv/v + 8 μv 0.11 mv/v + 8 μv 0.32 mv/v + 8 μv 0.85 mv/v + 25 μv 1.1 mv/v + 25 μv 1.7 mv/v + 35 μv 3.4 mv/v + 80 μv 0.5 mv/v + 80 μv 0.16 mv/v + 25 μv 0.75 mv/v + 6 μv 0/12 mv/v + 16 μv 0.25 mv/v + 70 μv 0.43 mv/v mv 1.1mV/V mv 2.2 mv/v mv 0.5 mv/v mv 0.16 mv/v mv 0.75 mv/v mv 0.12 mv/v mv 0.25 mv/v mv 0.50 mv/v mv 1.3 mv/v mv 2.7 mv/v mv HP 3458A Multimeter Fluke 5720A Opt 03 Multiproduct Calibrator Page 3 of 14

5 Electrical DC/Low Frequency AC Voltage 1 - Source AC Voltage 1 - Measure (22 to 220) V (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 khz 100 khz to 1 MHz (220 to 750) V (30 to 50) khz 220 V to 1.1 kv (15 to 50) Hz 50 Hz to 1 khz Up to 10 mv (1 to 40) Hz (1 to 20) khz (100 to 300) khz 10 mv to 10 V (1 to 40) Hz (1 to 20) khz (100 to 300) khz 300 khz to 1 MHz (1 to 2) MHz (10 to 100) V (1 to 40) Hz (100 to 300) khz 300 khz to 1 MHz 0.5 mv/v + 8 mv 0.16 mv/v mv 0.80 mv/v mv 0.22 mv/v mv 0.50 mv/v + 8 mv 16 mv/v V 0.6 mv/v + 11 mv 2.3 mv/v + 45 mv 0.4 mv/v + 16 mv 90 µv/v + 4 mv 0.3 mv/v + 3 µv 0.2 mv/v + 2 µv 0.3 mv/v + 2 µv 1.2 mv/v + 2 µv 5.8 mv/v + 2 µv 46 mv/v + 2 µv 80 µv/v mv 80 µv/v mv 0.2 mv/v mv 0.3 mv/v mv 0.9 mv/v mv 3.5 mv/v + 1 mv 12 mv/v + 1 mv 17 mv/v + 1 mv 0.2 mv/v + 4 mv 0.2 mv/v + 2 mv 0.4 mv/v + 2 mv 1.4 mv/v + 2 mv 4.6 mv/v + 10 mv 17 mv/v + 10 mv Fluke 5720A Opt 03 Multiproduct Calibrator Agilent 3458A Multimeter Page 4 of 14

6 Electrical DC/Low Frequency AC Voltage 1 - Measure AC Voltage 1 Measure AC Current 1 - Source AC Current 1 - Source AC Current 1 - Measure 100 V to 1 kv (1 to 40) Hz (1 to 20) khz (1 to 60) kv (20 to 100) Hz Up to 220 μa 220 μa to 22 ma (22 to 220) ma 220 ma to 2.2 A (1 to 1 000) A 0.50 mv/v + 40 mv 0.50 mv/v + 20 mv 0.70 mv/v + 20 mv 1.4 mv/v + 20 mv 3.5 mv/v + 20 mv 2 mv/v 0.9 ma/a 0.24 ma/a 0.26 ma/a 0.93 ma/a 60 Hz 5.4 ma/a Up to 100 μa (10 to 20) Hz (20 to 45) Hz 45 Hz to 1 khz 100 μa to 100 ma (10 to 20) Hz (20 to 45) Hz (45 to 100) Hz 100 Hz to 5 khz 100 ma to 1 A (10 to 20) Hz (20 to 45) Hz (45 to 100) Hz 100 Hz to 5 khz 4.6 ma/a µa 1.8 ma/a µa 0.78 ma/a µa 4.6 ma/a + 20 µa 1.7 ma/a + 20 µa 7.3 ma/a + 20 µa 4.2 ma/a + 20 µa 4.6 ma/a µa 1.9 ma/a µa 1 ma/a µa 1.2 ma/a µa Agilent 3458A Multimeter Ross VD-60 Voltage Divider Fluke 5720A Opt 03 Multiproduct Calibrator Fluke 5500A Multiproduct Calibrator with Coil Agilent 3458A Multimeter Page 5 of 14

7 Electrical DC/Low Frequency Capacitance 1 - Source at 1 khz Inductance - Measure 10 khz to 10 MHz Capacitance Measure 10 khz to 10 MHz Electrical Stimulation of Thermocouple Indicators 1 (330 to 490) pf 490 pf to 1.1 nf (1.1 to 3.3) nf (3.3 to 11) nf (11 to 33) nf (33 to 110) µf (110 to 330) µf 330 µf to 1.1 µf (1.1 to 3.3) µf 33 mf/f 14 mf/f 7.3 mf/f 5.1 mf/f 5.4 mf/f 3.2 mf/f 3.2 mf/f 2.9 mf/f 3.7 mf/f 100 µh to 10 H 0.13 mh/h (0 to 1 000) pf 3 mh/h Type E (-250 to -100) C (-100 to 650) C (650 to 1 000) C Type J (-210 to -100) C (-100 to 760) C (760 to 1 200) C Type K (-200 to -100) C (-100 to 1 000) C (1 000 to 1 372) C Type S (0 to 250) C (250 to 1 400) C (1 400 to 1 767) C Type T (-250 to -150) C (-150 to 0) C (0 to 400) C 0.31 C 0.23 C 0.21 C 0.29 C 0.21 C 0.19 C 0.32 C 0.29 C 0.36 C 0.38 C 0.49 C 0.46 C 0.59 C 0.54 C 0.57 C Fluke 5500A Multiproduct Calibrator HP 4275A LCR Bridge Fluke 5500A Multiproduct Calibrator Page 6 of 14

8 Electrical DC/Low Frequency Electrical Stimulation of RTD Indicators 1 Pt 395, 100 Ω (-200 to 0) C (0 to 100) C (100 to 400) C (400 to 630) C (630 to 800) C Pt 3926, 100 Ω (-200 to 0) C (0 to 100) C (100 to 400) C (400 to 630) C Pt 3916, 100 Ω (-200 to -190) C (-190 to 0) C (0 to 300) C (300 to 600) C (600 to 630) C Pt 385, 200 Ω (-200 to 100) C (100 to 260) C (260 to 600) C (600 to 630) C Pt 385, 500 Ω (-200 to 100) C (100 to 260) C (260 to 600) C (600 to 630) C Pt 385, 1 k Ω (-200 to 100) C (100 to 260) C (260 to 600) C (600 to 630) C PtNi 385, 100 Ω (-80 to 100) C (100 to 260) C Cu 427, 10 Ω (-100 to 260) C 0.05 C 0.05 C 0.1 C 0.12 C 0.23 C 0.05 C 0.07 C 0.1 C 0.12 C 0.25 C 0.05 C 0.08 C 0.1 C 0.23 C 0.04 C 0.05 C 0.14 C 0.16 C 0.05 C 0.06 C 0.09 C 0.11 C 0.03 C 0.05 C 0.07 C 0.23 C 0.08 C 0.14 C 0.3 C Fluke 5500A Multiproduct Calibrator Page 7 of 14

9 Electrical DC/Low Frequency Oscilloscopes 1 Square Wave Signal 50 Ω at 1 khz 1 MΩ at 1 khz +/- 1 mv to 6.6 V 1 mv to 130 V 1 mv/v + 40 µv 4 mv/v + 40 µv Pulse & Rise Time 0.5, 1 V (pp) 10 MHz 1 V (pp) 1 MHz 0.4 ns 0.4 ns Fluke 5500A/SC300 Multiproduct Calibrator Time Mark Output 2 Into 50 ohms 2 ns to 20 ms 50 ms to 5 s ( t) parts in 10 6 s 25 parts in 10 6 s Leveled Sinewave Flatness (0.005 to 5.5) V 50 khz Reference 50 khz to 100 MHz (100 to 300) MHz 2.4 % of reading nv 2.5 % of reading nv 4.3 % of reading nv Electrical RF/Microwave Tuned RF Power, Relative 1 - Measure 2.5 MHz to 26.5 GHz RF Absolute Power 1 - Measure (-30 to 20) db (-30 to 20) db (-30 to 20) db (-30 to 20) db (-30 to 20) db (0 to -3) db (-3 to 10) db (-10 to -40) db (-40 to -50) db (-50 to -80) db (-80 to -90) db (-90 to -110) db (-110 to -127) db 100 khz to 2.6 GHz 100 khz to 4.2 GHz 10 MHz to 16.5 GHz 10 MHz to 26.5 GHz 50 MHz to 50 GHz 0.04 db 0.03 db 0.07 db 0.08 db 0.09 db 0.11 db 0.14 db 0.2 db 0.6 db 0.65 db 0.68 db 0.69 db 0.84 db Receiver with Agilent 11722A, Agilent 11793A, Agilent 11792A Power Sensors Agilent 438A Power Meter, Receiver, Agilent 11722A, Agilent 8482A, Agilent 11792A, Agilent 8485A, Agilent 8487A Power Sensors Page 8 of 14

10 Electrical RF/Microwave Amplitude Modulation 1 Measure Frequency Modulation 1 Measure Phase Modulation 1 - Measure Reflection 1 S11/ S22 Measure - Type N Rate: 150 khz to 10 MHz (5 to 99) % Depth 50 Hz to 10 khz 20 Hz to 100 khz Rate: 10 MHz to 1.3 GHz (5 to 99) % Depth 50 Hz to 50 khz 20 Hz to 100 khz Rate: 1.3 GHz to 26.5 GHz (5 to 99) % Depth 50 Hz to 50 khz 20 Hz to 100 khz Rate: 250 khz to 10 MHz Dev: 40 khz 20 Hz to 10 khz Rate: 10 MHz to 1.3 GHz Dev: 400 khz 20 Hz to 200 khz 50 Hz to 100 khz Rate: (1.3 to 26.5) GHz 20 Hz to 100 khz 50 Hz to 100 khz 4 % Depth 4.6 % Depth 3.6 % Depth 4.6 % Depth 3.7 % Depth 4.7 % Depth 3.1 % of reading 7.7 % of reading 1.6 % of reading 7.7 % of reading 1.6 % of reading Rate: 10 MHz to 1.3 GHz 200 Hz to 20 khz 7 % of reading Rate: 1.3 GHz to 26.5 GHz 7.4 % of reading 200 Hz to 20 khz (0 to 1.0) lin mag -180 º to 180 º 300 khz to 6 GHz (6 to 26.5) GHz (26.5 to 50) GHz lin mag 1.2º lin mag 1.4º lin mag 1.7 Receiver Sensor Module Receiver with Agilent 11793APower Sensor Receiver Receiver with Agilent 11793APower Sensor Receiver Receiver with Agilent 11793APower Sensor HP 8753E, HP 8510C Network Analyzers Page 9 of 14

11 Length Dimensional metrology Micrometers, Calipers, Indicators and Height Gages 2 Up to 48 in (1.2R +10L) µin Blocks and End Standards Indicator Calibrator Cylindrical Rings Length Standards 2 (0.01 to 48) in (30 + 5L) µin Universal Comparator External Threads, Pitch Diameter, All English and Metric 60 Threads 2 Major Diameter Pitch Diameter Internal Threads Pitch Diameter (Tactile fit) Ring Gages, Plain Cylindrical 2 Cylindrical Plugs and Pin Gage, Diameter 2 (0.01 to 8) in ( L) µin ( L) µin Universal Length Measuring Machine, Thread Wires; Gage Blocks (0.1 to 4) in - Thread Setting Plugs (0.5 to 12) in ( L) µin (0.01 to 2.00) in (27 + 2L) µin Gage Blocks 2 (0.05 to 6) in ( L) µin Thread Wires (0.003 to 0.15) in (4 to 120) T.P.I. 10 µin Rigid Rules Up to 20ft in in/ft Surface Roughness Testers for Ra-Ry Optical Comparators and Vision Systems /Measuring Microscope 1 X/Y/Z Axis Surface Plates 1 Local Area Flatness Only (Repeat Reading) 4 µin, 120 µin 250 µin Universal Machine and Reference Cylindrical Rings Universal Length Measuring Machine, Gage Blocks LabMaster Vertical Reference Blocks Universal Length Measuring Machine, Gage Blocks Glass Scales Steel Rules 2.6 µin Roughness Specimen Up to 12 in 118 µin Gage Blocks (12 12) in to (72 144) in 250 µin Repeat-o-Meter Page 10 of 14

12 Mass and Mass Related Pressure 1 (-15 to 100) psi (100 to 500) psi 0.01 psi % of reading 0.05 psi % of reading Pressure Calibrator (100 to ) psi 0.01 psi % of reading Dead Weight Tester Pressure, Absolute (0 to 30) psia 0.01 psi % of reading Pressure Calibrator Vacuum (0.01 to 760) Torr 10 % of reading Reference Vacuum Gage Torque Tools 1 1 ozf in to lbf ft 1.2 % of reading Torque Calibrators Torque Analyzers 10 lbf in to 250 lbf ft 0.12 % of reading + 1.2R Torque Arm and Weights Force 1 Compression and Tension (1 to 500) lbf (500 to ) lbf 0.12 lbf 3.5 lbf Load Stand Proving Ring (0 to 100) mg (100 to 1 000) mg (1 to 2) g (2 to 5) g (5 to 10) g (10 to 20) g 1 µg 1.5 µg 3.2 µg 5.5 µg 9.2 µg 12.5 µg Mass (20 to 50) g 28 µg Class 1 Weights and (50 to 100) g 50 µg Balance (100 to 500) g (500 to 1 000) g (1 to 2) kg (2 to 5) kg (5 to 10) kg (10 to 25) kg 81 µg 0.5 mg 1 mg 2.5 mg 0.25 g 0.6 g Scales and Balances (1 to 2) g (2 to 5) g (5 to 10) g (10 to 20) g (20 to 50) g (50 to 100) g (100 to 500) g (500 to 1 000) g (1 to 2) kg (2 to 5) kg (5 to 10) kg (10 to 25) kg 3.2 µg 5.5 µg 9.2 µg 13 µg 28 µg 50 µg 81 µg 0.5 mg 1 mg 2.5 mg 0.25 g 0.6 g Class E1, E2, F and F1 Weights Page 11 of 14

13 Mass and Mass Related Scales and Balances POVA (Piston/Plunger Operated Volumetric Apparatus) Pipettes, Syringes, Dilutors, Titrators, Piston/Displacement Burettes (Burets), Dispensers, Liquid Handlers Volumetric Glassware Volumetric Apparatus, Flasks, Burettes, Volumetric Dispensers, Cylinders, Graduated Cylinders, Beakers, Vials, & Containers (0.01 to 50) lb (50 to 100) lb (100 to 500) lb (500 to 1 000) lb (0.1 to 5) μl (5 to 20) μl (20 to 50) μl (50 to 100) μl (100 to 200) μl (200 to 500) μl 500 μl to 1 ml (1 to 5) ml (5 to 10) ml (0.1 to 2) ml (2 to 25) ml (25 to 50) ml (50 to 100) ml (100 to 250) ml (250 to 500) ml (500 to 1 000) ml (1 000 to 2 000) ml g 0.03 g 1.5 g 2.4 g 1.8 % of reading 0.81 % of reading 0.75 % of reading 1 % of reading 1 % of reading 1.3 % of reading 1.3 % of reading 1.3 % of reading 1.3 % of reading 0.36 % of reading 0.15 % of reading 0.13 % of reading 0.1 % of reading 0.08 % of reading 0.05 % of reading 0.04 % of reading 0.04 % of reading Class E1, E2, F and F1 Weights Gravimetric Method referenced to OIML Class E1 Mass Standard and Balances Gravimetric Method referenced to OIML Class E1 Mass Standard and Balances Flow (1 to 40) l/min 1.5 % of reading Standard Flow Sensors Air Velocity (400 to 7 400) ft/min 2.6 % of reading Digital Anemometer Photometry and Radiometry Optical Power - Measure ( ) nm Optical Wavelength v - Measure (0 to 1 000) mw 3 % of reading Newport 818 Photodetector (0.01 to 1.0) W (1 to 100) W 2.8 % of reading 4.2 % of reading (700 to 1 650) nm nm Coherent PM-3 Power Meter Coherent LM-10, LM-100 Power Sensors Agilent 86120B Wavelength Meter Page 12 of 14

14 Photometry and Radiometry UV and Visible Spectrophotometry (240 to 1 640) nm 0.16 nm Aqueous Solution and Reference Filters Thermodynamic Humidity (10 to 80) %RH 1.4 %RH Dew Point (-80 to 20) C 1.8 C Vaisala HMi41 Humidity Indicator Vaisala MI70/DMP74B Humidity Indicator and Probe Humidity Source (10 to 95) %RH 3 %RH Espec BTX-475 Chamber Infrared Thermometers 1 Temperature - Measure Temperature Source (0 to 150) C (150 to 500) C (-40 to -200) C (0 to -40) C (0 to 160) C (160 to 230) C (230 to 420) C (420 to 660) C 6.1 C 7.2 C C C C C 0.02 C C Electro Optics Black Body Source Ɛ = 0.98, λ = (8 to 14) µm Hart 5614 PRT Hart 5626 PRT (-80 to 300) C 0.1 C Hart 7013 Bath (-70 to 150) C 2 C Espec BTX-475 Chamber Time and Frequency Frequency - Measure 10 MHz 5 parts in Hz Agilent A GPS Receiver Page 13 of 14

15 Time and Frequency Frequency 1 - Measure 10 Hz to 26.5 GHz 2.5 parts in Hz Agilent 8657 Signal Generator, Agilent 8902 Measuring Receiver, Frequency Counter Time Interval Measure 1 ns to 100 µs 0.21 % of reading + 5 ps Agilent Oscilloscope Elapsed Time 1 s to 24 hours 0.3 s Stop Watch Photo Tachometer (0 to ) rpm 0.4 rpm Strobe and Counter Calibration and Measurement Capability (CMC) is expressed in terms of the measurement parameter, measurement range, expanded uncertainty of measurement and reference standard, method, and/or equipment. The expanded uncertainty of measurement is expressed as the standard uncertainty of the measurement multiplied by a coverage factor of 2 (k=2), corresponding to a confidence level of approximately 95%. Notes: 1. On-site calibration service is available for this parameter, since on-site conditions are typically more variable than those in the laboratory, larger measurement uncertainties are expected on-site than what is reported on the accredited scope. 2. L = length in inches, R = resolution of unit under test, t = time in seconds. 3. This scope is formatted as part of a single document including Certificate of Accreditation No. AC Page 14 of 14