SCOPE OF ACCREDITATION TO ISO/IEC 17025:2017 & ANSI/NCSL Z

Transcription

1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2017 & ANSI/NCSL Z INDUSTRIAL PROCESS MEASUREMENT, INC Park Avenue, Unit 7 Edison, NJ Mark Gural Phone: CALIBRATION Valid To: December 31, 2020 Certificate Number: In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following calibrations 1, 8 : I. Acoustical Quantities Parameter/Equipment Frequency CMC 2, 5, 7 ( ) Comments Sound Pressure Level 3 Measure (70 to 130) db 0.61 db Quest 1800 meter & ACO 7023 microphone 250 Hz to 1 khz Hz Frequency counter Sound Level 3 Measurement Equipment 114 db, 125 Hz to 2 khz (84, 104) db, 125 Hz to 4 khz 0.32 db + 0.6R 0.59 db + 0.6R Genrad 1986 meter Re: 20 µpa (74, 94) db, 125 Hz to 4 khz 0.71 db + 0.6R 114 db, 4 khz 0.59 db + 0.6R (A2LA Cert. No ) Revised 12/05/2018 Page 1 of 17

2 II. Dimensional Parameter/Equipment Range CMC 2, 5 ( ) Comments Outside Micrometers Up to 1 in (1 to 12) in ( R) μin ( L + 0.6R) μin Gage blocks Calipers (OD, ID, Depth, Step) Up to 12 in ( L + 0.6R) μin Gage blocks III. Electrical DC/Low Frequency Parameter/Equipment Range CMC 2, 4 ( ) Comments DC Voltage 3 Generate (0 to 220) mv (> 0.22 to 2.2) V (> 2.2 to 11) V (> 11 to 22) V (> 22 to 220) V (> 220 to 1100) V 7.6 μv/v μv 6.2 μv/v μv 6.2 μv/v μv 6.2 μv/v μv 7.0 μv/v + 78 μv 8.8 μv/v mv Fluke 5700A DC Voltage 3 Measure (0 to 100) mv (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V 13 μv/v μv 12 μv/v μv 12 μv/v μv 14 μv/v + 30 μv 14 μv/v mv + 12 μv/v (V IN /1000) 2 HP 3458A (> 1000 to ) V (> to ) V 0.03 % V 0.06 % V Vitrek 4700 & Vitrek HVL-100 DC Current 3 Generate (0 to 220) µa > 220 µa to 2.2 ma (> 2.2 to 22) ma (> 22 to 220) ma (> 220 to 2.2) A (> 2.2 to 11) A (> 11 to 20) A 47 μa/a + 10 na 47 μa/a + 10 na 56 μa/a + 80 na 54 μa/a μa 81 μa/a + 12 μa % μa % + 1 ma Fluke 5700A Fluke 5500A Fluke 5700A & 5220A DC Current 3 Generate Non-Toroidal (> 20 to 110) A (> 110 to 550) A 0.63 % A 0.58 % A Fluke 5500A & Fluke 5500-A coil (550 to 1000) A 0.63 % A Fluke 5522A, Fluke 5500-A coil (A2LA Cert. No ) Revised 12/05/2018 Page 2 of 17

3 Parameter/Equipment Range CMC 2, 4, 6 ( ) Comments DC Current 3 Measure (0 to 100) na > 100 na to 1 μa (> 1 to 10) μa (> 10 to 100) µa > 100 µa to 1 ma (> 1 to 10) ma (> 10 to 100) ma > 100 ma to 1 A 61 μa/a + 40 pa 54 μa/a + 40 pa 29 μa/a pa 29 μa/a na 27 μa/a µa 43 μa/a µa 46 μa/a µa % + 10 μa HP 3458A (> 1 to 20) A % HP 3458A & Y5020 (> 20 to 400) A (> 400 to 1000) A 1.5 % A 1.5 % + 3 A LEM HEME LH2040 DC Resistance 3 Measure (0 to 10) Ω (> 10 to 100) Ω > 100 Ω to 1 kω (> 1 to 10) kω (> 10 to 100) kω > 100 kω to 1 MΩ (> 1 to 10) MΩ (> 10 to 100) MΩ > 100 MΩ to 1 GΩ 23 µω/ω + 50 µω 17 µω/ω µω 15 µω/ω µω 15 µω/ω + 5 mω 15 µω/ω + 50 mω 15 µω/ω + 2 Ω 66 µω/ω Ω % + 1 kω 0.58 % + 10 kω HP 3458A DC Power 3 Generate µw to 9.18 W 297 µw to 33.7 W mw to 91.8 W 2.97 mw to 337 W mw to 918 W 29.7 mw to kw 72.6 mw to 4.59 kw mw to kw % % % % % % % % Fluke 5500A (A2LA Cert. No ) Revised 12/05/2018 Page 3 of 17

4 Parameter/Equipment Range CMC 2, 4, 6 ( ) Comments DC Resistance 3 Generate (0 to 10.9) Ω (11 to 32.9) Ω (33 to 109.9) Ω (110 to 329.9) Ω 330 Ω to 1.09 kω (1.1 to 3.29) kω (3.3 to 10.9) kω (11 to 32.9) kω (33 to 109.9) kω (110 to 329) kω 330 kω to 1.09 MΩ (1.1 to 3.29) MΩ (3.3 to 10.9) MΩ (11 to 32.9) MΩ (33 to 109.9) MΩ (110 to 330) MΩ 94 µω/ω Ω 94 µω/ω Ω 70 µω/ω Ω 70 µω/ω Ω 70 µω/ω Ω 70 µω/ω Ω 70 µω/ω Ω 70 µω/ω Ω % + 5 Ω % + 5 Ω % + 43 Ω % + 43 Ω % Ω % Ω 0.39 % kω 0.39 % + 13 kω Fluke 5500A Fixed Points 0 Ω 1 Ω 1.9 Ω 10 Ω 19 Ω 100 Ω 190 Ω 1 kω 1.9 kω 10 kω 19 kω 100 kω 190 kω 1 MΩ 1.9 MΩ 10 MΩ 19 MΩ 100 MΩ 40 µω 86 µω/ω 85 µω/ω 26 µω/ω 25 µω/ω 16 µω/ω 16 µω/ω 12 µω/ω 12 µω/ω 11 µω/ω 11 µω/ω 12 µω/ω 17 µω/ω 30 µω/ω 41 µω/ω 48 µω/ω 70 µω/ω % Fluke 5700A (A2LA Cert. No ) Revised 12/05/2018 Page 4 of 17

5 Parameter/Range Frequency CMC 2, 4 ( ) Comments AC Voltage 3 Generate (0.22 to 2.2) mv > 40 Hz to 20 khz (> 20 to 50) khz (> 50 to 100) khz (> 100 to 300) khz (> 300 to 500) khz > 500 khz to 1 MHz % + 4 μv % + 4 μv % + 4 μv % + 4 μv % + 6 μv 0.1 % + 12 μv 0.14 % + 23 μv 0.28 % + 23 μv Fluke 5700A (2.2 to 22) mv > 40 Hz to 20 khz (> 20 to 50) khz (> 50 to 100) khz (> 100 to 300) khz (> 300 to 500) khz > 500 khz to 1 MHz % + 4 μv % + 4 μv % + 4 μv % + 4 μv % + 5 μv 0.10 % + 10 μv 0.14 % + 20 μv 0.28 % + 20 μv (22 to 220) mv > 40 Hz to 20 khz (> 20 to 50) khz (> 50 to 100) khz (> 100 to 300) khz (> 300 to 500) khz > 500 khz to 1 MHz % + 12 μv % + 8 μv % + 8 μv % + 8 μv % + 23 μv % + 23 μv 0.14 % + 31 μv 0.28 % + 78 μv 220 mv to 2.2 V > 40 Hz to 20 khz (> 20 to 50) khz (> 50 to 100) khz (> 100 to 300) khz (> 300 to 500) khz > 500 khz to 1 MHz % + 78 μv % + 23 μv % + 5 μv % + 16 μv % + 62 μv % mv % mv 0.19 % mv (A2LA Cert. No ) Revised 12/05/2018 Page 5 of 17

6 Parameter/Range Frequency CMC 2, 4 ( ) Comments AC Voltage 3 Generate (cont) (2.2 to 22) V > 40 Hz to 20 khz (> 20 to 50) khz (> 50 to 100) khz (> 100 to 300) khz (> 300 to 500) khz > 500 khz to 1 MHz % mv % mv % + 54 μv % mv % mv % mv 0.11 % mv 0.23 % mv Fluke 5700A (22 to 220) V > 40 Hz to 20 khz (> 20 to 50) khz (> 50 to 100) khz (> 100 to 300) khz (> 300 to 500) khz > 500 khz to 1 MHz % mv % mv % mv % mv % mv 0.12 % + 85 mv 0.42 % + 85 mv 1.0 % mv (220 to 1100) V 50 Hz to 1 khz % mv AC Voltage 3 Measure (1 to 10) mv (1 to 40) Hz 40 Hz to 1 khz (1 to 20) khz (20 to 50) khz (50 to 100) khz (100 to 300) khz % + 3 µv % µv % µv 0.12 % μv 0.58 % μv 4.6 % + 2 μv HP 3458A (10 to 100) mv (1 to 40) Hz 40Hz to 1 khz (1 to 20) khz (20 to 50) khz (50 to 100) khz (100 to 300) khz 300 khz to 1 MHz (1 to 2) MHz % + 4 μv % + 2 μv % + 2 μv % + 2 μv % + 2 μv 0.35 % + 10 μv 1.2 % + 10 µv 1.8 % + 10 µv 100 mv to 1 V (1 to 40) Hz 40 Hz to 1 khz (1 to 20) khz (20 to 50) khz (50 to 100) khz (100 to 300) khz 300 khz to 1 MHz (1 to 2) MHz 0.01 % + 40 μv 0.01 % + 20 μv % + 20 μv % + 20 μv % + 20 μv 0.35 % μv 1.2 % μv 1.7 % μv (A2LA Cert. No ) Revised 12/05/2018 Page 6 of 17

7 Parameter/Range Frequency CMC 2, 4, 6 ( ) Comments AC Voltage 3 Measure (cont) (1 to 10) V (1 to 40) Hz 40 Hz to 1 khz (1 to 20) khz (20 to 50) khz (50 to 100) khz (100 to 300) khz 300 khz to 1 MHz (1 to 2) MHz % μv % μv % μv % μv % μv 0.35 % + 1 mv 1.2 % + 1 mv 1.7 % + 1 mv HP 3458A (10 to 100) V (1 to 40) Hz 40 Hz to 1 khz (1 to 20) khz (20 to 50) khz (50 to 100) khz (100 to 300) khz 300 khz to 1 MHz % + 4 mv % + 2 mv % + 2 mv % + 2 mv 0.14 % + 2 mv 0.46 % + 10 mv 1.7 % + 10 mv (100 to 700) V (1 to 40) Hz 40 Hz to 1 khz % + 40 mv % + 20 mv (700 to ) V ( to ) V 60 Hz 60 Hz 0.14 % V 0.16 % V Vitrek 4700 & Vitrek HVL-100 AC Current 3 Generate Up to 220 µa > 40 Hz to 1 khz (> 1 to 5) khz (> 5 to 10) khz % + 20 na % + 20 na % + 20 na 0.12 % + 40 na 0.17 % + 80 na Fluke 5700A (> 0.22 to 2.2) ma > 40 Hz to 1 khz (> 1 to 5) khz (> 5 to 10) khz % + 40 na % + 30 na % + 30 na % na 0.14 % na (2.2 to 22) ma > 40 Hz to 1 khz (> 1 to 5) khz (> 5 to 10) khz % na % na % na % + 4 μa 0.14 % + 8 μa (> 22 to 220) ma > 40 Hz to 1 khz (> 1 to 5) khz (> 5 to 10) khz % + 4 μa % + 3 μa % + 3 μa % + 39 μa 0.14 % + 78 μa (A2LA Cert. No ) Revised 12/05/2018 Page 7 of 17

8 Parameter/Range Frequency CMC 2, 4 ( ) Comments AC Current 3 Generate (cont) (> 0.22 to 2.2) A 40 Hz to 1 khz (> 1 to 5) khz (> 5 to 10) khz % + 31 μa % + 78 μa 0.78 % μa Fluke 5700A (> 2.2 to 11) A (45 to 65) Hz (65 to 500) Hz 500 Hz to 1 khz 0.06 % ma 0.09 % ma 0.26 % ma Fluke 5500A (> 11 to 20) A 40 Hz to 1 khz % + 1 ma Fluke 5700A/5220A AC Current 3 Generate Toroidal (> 1.65 to 110) A (> 110 to 550) A (45 to 65) Hz (45 to 65) Hz 0.38 % A 0.29 % A Fluke 5500A & Fluke 5500A coil (550 to 1000) A (45 to 65) Hz 0.39 % A Fluke 5522A, Fluke 5500A coil AC Current 3 Generate Non-Toroidal (> 1.65 to 110) A (> 110 to 550) A (45 to 65) Hz (45 to 65) Hz 0.63 % A 0.58 % A Fluke 5500A & Fluke 5500A coil (550 to 1000) A (45 to 65) Hz 0.64 % A Fluke 9100, Fluke 5500A coil AC Current 3 Measure (5 to 100) μa (20 to 45) Hz (45 to 100) Hz 100 Hz to 1 khz 0.46 % + 30 na 0.18 % + 30 na % + 30 na 0.07 % + 30 na HP 3458A 100 μa to 1 ma (20 to 45) Hz (45 to 100) Hz 100 Hz to 5 khz (5 to 20) khz (20 to 50) khz (50 to 100) khz 0.46 % na 0.17 % na 0.07 % na % na 0.07 % na 0.46 % na 0.64 % μa (A2LA Cert. No ) Revised 12/05/2018 Page 8 of 17

9 Parameter/Range Frequency CMC 2, 4, 6 ( ) Comments AC Current 3 Measure (cont) (1 to 10) ma (20 to 45) Hz (45 to 100) Hz 100 Hz to 5 khz (5 to 20) khz (20 to 50) khz (50 to 100) khz 0.47 % + 2 μa 0.18 % + 2 μa 0.07 % + 2 μa % + 2 μa 0.07 % + 2 μa 0.47 % + 4 μa 0.64 % + 15 μa HP 3458A (10 to 100) ma (20 to 45) Hz (45 to 100) Hz 100 Hz to 5 khz (5 to 20) khz (20 to 50) khz (50 to 100) khz 0.47 % + 20 μa 0.18 % + 20 μa 0.07 % + 20 μa % + 20 μa 0.07 % + 20 μa 0.47 % + 40 μa 0.64 % μa 100 ma to 1 A (20 to 45) Hz (45 to 100) Hz 100 Hz to 5 khz (5 to 20) khz (20 to 50) khz 0.47 % μa 0.2 % μa 0.11 % μa 0.13 % μa 0.35 % μa 1.2 % μa (> 1 to 20) A (1 to 40) Hz 40 Hz to 1 khz (1 to 5) khz % % % HP 3458A & Y5020 (> 20 to 400) A (> 400 to 1000) A (45 to 65) Hz (45 to 65) Hz 1.5 % A 1.5 % + 3 A LEM HEME LH2040 (A2LA Cert. No ) Revised 12/05/2018 Page 9 of 17

10 Parameter/Equipment Range CMC 2, 4, 6 ( ) Comments AC Power 3 Generate (45 to 65 Hz) PF = µw to 2.97 mw 297 µw to mw (1.089 to 29.7) mw (2.97 to 108.9) mw (10.89 to 297) mw (297 to 726) mw 72.6 mw to W mw to 3.63 W mw to 9.18 W 2.97 mw to 33.7 W mw to 91.8 W 29.7 mw to 337 W mw to 918 W 297 mw to kw 726 mw to 4.59 kw W to kw 0.32 % 0.20 % 0.28 % 0.21 % 0.34 % 0.24 % 0.29 % 0.21 % 0.20 % 0.13 % 0.20 % 0.14 % 0.28 % 0.18 % 0.18 % 0.14 % Fluke 5500A Capacitance 3 Generate (0.33 to ) nf (0.5 to ) nf (1.1 to ) nf (3.3 to ) nf (11 to ) nf (33 to ) nf (110 to ) nf (0.33 to ) µf (1.1 to ) µf (3.3 to ) µf (11 to ) µf (33 to ) µf (110 to ) µf 330 µf to 1.1 mf 0.39 % nf 0.39 % nf 0.39 % nf 0.2 % nf 0.2 % nf 0.2 % nf 0.2 % nf 0.2 % + 1 nf 0.27 % + 2 nf 0.27 % + 8 nf 0.31 % + 23 nf 0.39 % + 78 nf 0.54 % nf 0.78 % + 1 µf Fluke 5500A (A2LA Cert. No ) Revised 12/05/2018 Page 10 of 17

11 Parameter/Equipment Range CMC 2, 4 ( ) Comments Oscilloscopes Leveled Sine Wave 3 Generate, 50 khz Reference 5 mv to 5.5 V (pk-pk) 50 khz 50 khz to 100 MHz (100 to 300) MHz (300 to 600) MHz 1.6 % mv 2.7 % mv 3.1 % mv 4.7 % mv Fluke 55XXA/SC600 Flatness (Relative to 50 khz Ref) 50 khz to 100 MHz (100 to 300) MHz (300 to 600) MHz 1.2 % + 78 µv 1.6 % + 78 µv 3.1 % + 78 µv Vertical Gain DC Into 50 Ω Into 1 MΩ (0 to 2.2) V (0 to 33) V 0.19 % + 31 µv 0.04 % + 31 µv AC Into 50 Ω Into 1 MΩ 1 mv to 2.2 V (pk-pk) 1 mv to 105 V (pk-pk) 0.19 % + 31 µv 0.08 % + 31 µv Time Markers Into 50 Ω 5 s to 50 ms 20 ms to 100 ns (50 to 20) ns 10 ns (5 to 2) ns 20 µs/s + (t 0.7) ms/s 2 µs/s 2 µs/s 2 µs/s 2 µs/s Electrical Simulation of RTDs 3 Pt 385, 100 Ω (-200 to 0) C (0 to 100) C (100 to 300) C (300 to 400) C (400 to 630) C (630 to 800) C 0.04 C 0.05 C 0.07 C 0.08 C 0.09 C 0.18 C Fluke 5500A Pt 3926, 100 Ω (-200 to 0) C (0 to 100) C (100 to 300) C (300 to 400) C (400 to 630) C 0.04 C 0.05 C 0.07 C 0.08 C 0.09 C Pt 3916, 100 Ω (-200 to -190) C (-190 to -80) C (-80 to 0) C (0 to 100) C (100 to 260) C (260 to 300) C (300 to 400) C (400 to 600) C (600 to 630) C 0.19 C 0.03 C 0.04 C 0.05 C 0.05 C 0.06 C 0.07 C 0.08 C 0.18 C (A2LA Cert. No ) Revised 12/05/2018 Page 11 of 17

12 Parameter/Equipment Range CMC 2, 4 ( ) Comments Electrical Simulation of Thermocouples 3 Type E (-250 to -100) C (-100 to -25) C (-25 to 350) C (350 to 650) C (650 to 1000) C 0.45 C 0.26 C 0.26 C 0.26 C 0.28 C Fluke 5500A Type J (-210 to -100) C (-100 to -30) C (-30 to 150) C (150 to 760) C (760 to 1200) C 0.31 C 0.26 C 0.26 C 0.27 C 0.29 C Type K (-200 to -100) C (-100 to -25) C (-25 to 120) C (120 to 1000) C (1000 to 1372) C 0.35 C 0.27 C 0.27 C 0.32 C 0.40 C Type R (0 to 250) C (250 to 400) C (400 to 1000) C (1000 to 1767) C 0.5 C 0.36 C 0.35 C 0.39 C Type S (0 to 250) C (250 to 1000) C (1000 to 1400) C (1400 to 1767) C 0.43 C 0.36 C 0.37 C 0.43 C Type T (-250 to -150) C (-150 to 0) C (0 to 120) C (120 to 400) C 0.55 C 0.32 C 0.29 C 0.28 C (A2LA Cert. No ) Revised 12/05/2018 Page 12 of 17

13 IV. Electrical RF/Microwave Parameter/Range Frequency CMC 2, 4, 5 ( ) Comments RF Power Measure (20 to -49) dbm (-49 to -55) dbm (-55 to -60) dbm 50 MHz to 26.5 GHz 0.2 db 0.6 db 2.2 db Agilent E4418A & E4413A (20 to -17) dbm (-17 to -20) dbm 50 MHz to 39 GHz 0.20 db 0.36 db Agilent E4418A & 8487A (20 to -17) dbm (-17 to -20) dbm (39 to 50) GHz 0.27 db 0.36 db RF Power Measuring Equipment (+13 to -100) dbm 9 khz to 2.5 GHz (2.5 to 3.2) GHz (3.2 to 4) GHz ( R) db ( R) db ( R) db HP8648D V. Fluid Quantities Parameter/Equipment Range CMC 2, 5, 6, 7 ( ) Comments Air Velocity Anemometers & Air Velocity Meters (30 to 250) SFPM (0.15 to 1.25) m/s (250 to 1500) SFPM (1.25 to 7.5) m/s (2.7 % R) SFPM (2.3 % R) SFPM Wind tunnel by differential method (1500 to 9000) SFPM (7.5 to 45) m/s (1.2 % R) SFPM Air Velocity Measure (0 to 9000) SFPM (2.5 % R) SFPM Standard anemometer (A2LA Cert. No ) Revised 12/05/2018 Page 13 of 17

14 VI. Mechanical Parameter/Equipment Range CMC 2, 5, 6, 7 ( ) Comments Pressure/Vacuum 3 Pneumatic (-29.2 to -1) inhg (0 to 15) psia (15 to 100) psia (0 to 10) inh 2 O (10 to 250) inh 2 O (3 to 500) psig % + 0.6R psia + 0.6R 0.05 psia + 0.6R 0.01 inh 2 O + 0.6R % + 0.6R % + 0.6R AQS pressure module Hydraulic (200 to ) psi % + 0.6R Ametek PKII DWT P DWT (> to ) psi 0.01 % Pa + 0.6R P3214-PSI DWT SI - Barnet DWT Torque 3 Measuring Devices (5 to 10) lbf in (10 to 240) lbf in (20 to 100) lbf ft (100 to 200) lbf ft (200 to 1000) lbf ft 1.2 % 1.2 % 0.7 % 1.2 % 0.72 % Torque transducers Handheld Force Gages 3 (Tension) (0 to 10) lbf (0 to ) kgf 0.5 gf + 0.6R NIST Class F weights (10 to 100) lbf ( to ) kgf 4.8 gf + 0.6R (A2LA Cert. No ) Revised 12/05/2018 Page 14 of 17

15 Parameter/Equipment Range CMC 2, 5, 6 ( ) Comments Balances/Scales 3 Up to 50 g (50 to 100) g (100 to 200) g (200 to 300) g (300 to 410) g 0.13 mg 0.15 mg 0.25 mg 0.3 mg 0.41 mg ASTM Class 0 weights (410 to 750) g (750 to 1000) g (1 to 1.8) kg 0.69 mg 0.8 mg 1.1 mg ASTM Class 1 weights (1.8 to 5) kg 210 mg ASTM Class 1 & Class 2 weights (5 to 10) kg (10 to 25) kg (25 to 50) kg (50 to 120) kg 0.73 g 1.9 g 4.5 g 8.6 g NIST Class F weights Up to 50 lb ( ) kg 2.7 g ASTM Class 0 weights (50 to 100) lb ( to ) kg 3.8 g ASTM Class 1 weights (100 to 200) lb ( to ) kg 5.8 g ASTM Class 1 & Class 2 weights (200 to 300) lb ( to ) kg 7.4 g NIST Class F weights (A2LA Cert. No ) Revised 12/05/2018 Page 15 of 17

16 VII. Thermodynamic Parameter/Equipment Range CMC 2, 5, 7 ( ) Comments Temperature 3 Measure (-196 to 0) C (> 0 to 100) C (> 100 to 420) C (> 420 to 660) C C C C C Fluke 5626 PRT, Fluke 1521 Temperature 3 Measuring Equipment -196 C (-20 to 100) C (> 100 to 150) C (> 150 to 400) C (> 400 to 650) C C + 0.6R C + 0.6R C + 0.6R 0.12 C + 0.6R 0.13 C + 0.6R LN 2, Fluke 5626 PRT, Fluke 1521, temperature baths Infrared Radiation Thermometry 3 35 C (> 35 to 100) C (> 100 to 200) C (> 200 to 350) C (> 350 to 500) C 0.49 C + 0.6R 0.71 C + 0.6R 1.1 C + 0.6R 1.8 C + 0.6R 2.4 C + 0.6R Fluke 4181 black body Ɛ = 0.9 to 1.0 ʎ = (8 to 14) µm Humidity 3 (15 to 35) C (10 to 20) % RH (> 20 to 50) % RH (> 50 to 95) % RH 0.59 % RH 0.65 % RH 0.76 % RH Thunder Scientific 1200 VIII. Time & Frequency Parameter/Equipment Range CMC 2, 5, 7 ( ) Comments Frequency 3 Measure 0.1 Hz to 3 GHz Hz/Hz HP 53132A & Spectracomm 8194B Frequency 3 Measuring Equipment Hz to 9 khz Hz/Hz HP33250A & Spectracomm 8194B 9 khz to 4 GHz Hz/Hz HP8648D & Spectracomm 8194B Stopwatches & Timers 3 Up to s/day s/day Frequency counter time base (A2LA Cert. No ) Revised 12/05/2018 Page 16 of 17

17 1 This laboratory offers commercial calibration service and field calibration service. 2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer s device and to influences from the circumstances of the specific calibration. 3 Field calibration service is available for this calibration and this laboratory meets A2LA R104 General Requirements: Accreditation of Field Testing and Field Calibration Laboratories for these calibrations. Please note the actual measurement uncertainties achievable on a customer's site can normally be expected to be larger than the CMC found on the A2LA Scope. Allowance must be made for aspects such as the environment at the place of calibration and for other possible adverse effects such as those caused by transportation of the calibration equipment. The usual allowance for the actual uncertainty introduced by the item being calibrated, (e.g. resolution) must also be considered and this, on its own, could result in the actual measurement uncertainty achievable on a customer s site being larger than the CMC. 4 The stated measured values are determined using the indicated instrument (see Comments). This capability is suitable for the calibration of the devices intended to measure or generate the measured value in the ranges indicated. CMC s are expressed as either a specific value that covers the full range or as a percent or fraction of the reading plus a fixed floor specification. 5 In the statement of CMC, R is the resolution of the unit under test (same unit as the CMC uncertainty). In the statement of CMC, L is the numerical value of the nominal length of the device measured in inches. 6 In the statement of CMC, % refers to % of reading unless otherwise noted. 7 The type of instrument or material being calibrated is defined by the parameter. This indicates the laboratory is capable of calibrating instruments that measure or generate the values in the ranges indicated for the listed measurement parameter. 8 This scope meets A2LA s P112 Flexible Scope Policy. (A2LA Cert. No ) Revised 12/05/2018 Page 17 of 17

18 Accredited Laboratory A2LA has accredited INDUSTRIAL PROCESS MEASUREMENT, INC. Edison, NJ for technical competence in the field of Calibration This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2017 General requirements for the competence of testing and calibration laboratories. This laboratory also meets the requirements of ANSI/NCSL Z and R205 Specific Requirements: Calibration Laboratory Accreditation Program. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated April 2017). Presented this 26 th day of November President and CEO For the Accreditation Council Certificate Number Valid to December 31, 2020 Revised on December 5, 2018 For the calibrations to which this accreditation applies, please refer to the laboratory s Calibration Scope of Accreditation.