SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005

Transcription

1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 APTIV CONTRACT SERVICES. S. DE R. L. DE C. V. CALIBRATION LAB Mexico Technical Center Ave. Hermanos Escobar #5756 Cd. Juarez, Chihuahua C.P , Mexico Ricardo Arcibar Phone: CALIBRATION Valid To: November 30, 2019 Certificate Number: In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following calibrations 1 : I. Chemical Parameter/Equipment Range CMC 2 ( ) Comments ph 4 ph 7 ph 10 ph 0.02 ph 0.02 ph 0.02 ph Solution buffer II. Dimensional Parameter/Equipment Range CMC 2 ( ) Comments Length Standards Calipers Up to 6 in (6 to 12) in (12 to 36) in 330 μin 410 μin 790 μin Gage blocks Micrometer Up to 1 in (1 to 12) in 110 μin 290 μin Height Gages Up to 6 in (6 to 12) in (12 to 36) in 330 μin 410 μin 790 μin (A2LA Cert. No ) Revised 07/11/2018 Page 1 of 11

2 Parameter/Equipment Range CMC 2 ( ) Comments Angle Measuring Equipment (0 to 90)º 0.2º Angle block Pin Gage Diameter (0.025 to 1) in 50 μin Laser micrometer Indicators Test & Dial Up to 1 in (1 to 4) in 110 μin 140 μin Gage blocks Optical Comparators Up to 50 mm 7 μm Optical scales Ruler/Scale Up to 36 in 750 µin Gage blocks III. Electrical DC/Low Frequency Parameter/Equipment Range CMC 2, 4 ( ) Comments DC Voltage Measure, Fixed Points 100 mv 1 V 10 V 100 V 1000 V 1.6 μv 11 µv 100 µv 1.3 mv 26 mv HP 3458A DC Voltage Generate Up to mv (0.33 to 3.29) V (3.3 to 32.9) V (33 to 329.9) V (330 to 1020) V % + 1 µv % + 2 µv % + 20 µv % µv % mv DC Current Measure, Fixed Points 100 µa 1 ma 10 ma 100 ma 1 A 3 A 30 A 3.5 na 40 na 400 na 8 µa 170 µa 5.0 ma 80 ma HP 3458A HP 34401A HP 34330A, HP 3458A (A2LA Cert. No ) Revised 07/11/2018 Page 2 of 11

3 Parameter/Equipment Range CMC 2, 4 ( ) Comments DC Current Generate Up to μa (0.33 to 3.29) ma (3.3 to 32.9) ma (33 to 329.9) ma (0.33 to 1.09) A (1.1 to 2.9) A (3 to 10.9) A (11 to 20.5) A % µa % µa % µa % µa % + 40 µa % + 40 µa % µa 0.12 % µa Resistance Measure, Fixed Points k 10 k 100 k 1 M 10 M 100 M 510 µ 4.0 m 17 m 170 m k HP 3458A Resistance Generate (0 to 10.9) Ω (11 to 32.9) Ω (33 to 109.9) Ω (110 to 329.9) Ω 330 Ω to 1.09 kω (1.1 to 3.29) kω (3.3 to 10.9) kω (11 to 32.9) kω (33 to 109.9) kω (110 to 329.9) kω 330 kω to 1.09 MΩ (1.1 to 3.29) MΩ (3.3 to 10.9) MΩ (11 to 32.9) MΩ (33 to 109.9) MΩ (110 to 329.9) MΩ (330 to 1100) MΩ 490 µ 1.3 m 3.5 m 10 m 33 m 100 m 340 m k 10 k 60 k 1 M 2 M (A2LA Cert. No ) Revised 07/11/2018 Page 3 of 11

4 Parameter/Range Frequency CMC 2, 4 ( ) Comments AC Voltage Measure 100 mv 1 V 10 V 100 V 750 V 35 µv 350 μv 1.4 mv 47 mv 720 mv HP 3458A AC Current Measure, Fixed Points 1 A 3 A 2.0 ma 6.0 ma HP 34401A AC Voltage Generate (0.33 to 3.29) V (10 to 45) Hz 45 Hz to 10 khz (10 to 20) khz (20 to 50) khz (50 to 100) khz (100 to 500) khz 0.04 % + 50 µv 0.02 % + 60 µv 0.02 % + 60 µv 0.04 % + 50 µv 0.08 % µv 0.3 % µv (3.3 to 32.9) V (10 to 45) Hz 45 Hz to 10 khz (10 to 20) khz (20 to 50) khz (50 to 100) khz 0.04 % µv 0.02 % µv 0.02 % µv 0.04 % µv 0.10 % mv (33 to 329.9) V (1 to 10) khz (10 to 20) khz (20 to 50) khz (50 to 100) khz 0.02 % + 2 mv 0.02 % + 6 mv 0.03 % + 6 mv 0.04 % + 6 mv 0.24 % + 50 mv (330 to 1020) V 0.02 % + 10 mv 0.02 % + 10 mv 0.02 % + 10 mv (1.0 to 32.9) mv (10 to 45) Hz 45 Hz to 10 khz (10 to 20) khz (20 to 50) khz (50 to 100) khz (100 to 500) khz 0.09 % + 6 µv 0.04 % + 6 µv 0.04 % + 6 µv 0.13 % + 6 µv 0.45 % + 12 µv 1.1 % + 50 µv (A2LA Cert. No ) Revised 07/11/2018 Page 4 of 11

5 Parameter/Range Frequency CMC 2, 4 ( ) Comments AC Voltage Generate (cont) (33 to 329.9) mv (10 to 45) Hz 45 Hz to 10 khz (10 to 20) khz (20 to 50) khz (50 to 100) khz (100 to 500) khz 0.04 % + 8 µv 0.02 % + 8 µv 0.02 % + 8 µv 0.04 % + 8 µv 0.10 % + 32 µv 0.25 % + 70 µv AC Current Generate (29 to 329.9) μa (10 to 20) Hz (20 to 45) Hz (10 to 30) khz 0.3 % µa 0.2 % µa 0.2 % µa 0.4 % µa 1.0 % µa 1.9 % µa (0.3 to 3.29) ma (10 to 20) Hz (20 to 45) Hz (10 to 30) khz 0.25 % µa 0.15 % µa 0.12 % µa 0.25 % µa 0.6 % µa 1.2 % µa (3.3 to 32.9) ma (10 to 20) Hz (20 to 45) Hz (10 to 30) khz 0.2 % + 2 µa 0.1 % + 2 µa 0.05 % + 2 µa 0.1 % + 2 µa 0.2 % + 3 µa 0.5 % + 4 µa (33 to 329.9) ma (10 to 20) Hz (20 to 45) Hz (10 to 30) khz 0.2 % + 20 µa 0.1 % + 20 µa 0.05 % + 20 µa 0.15 % + 50 µa 0.3 % µa 0.5 % µa (0.33 to 1.09) A (10 to 45) Hz 0.2 % µa 0.06 % µa 0.7 % + 1 ma 3.2 % + 5 ma (A2LA Cert. No ) Revised 07/11/2018 Page 5 of 11

6 Parameter/Range Frequency CMC 2, 4 ( ) Comments AC Current Generate (cont) (1.1 to 2.9) A (10 to 45) Hz 0.2 % µa 0.07 % µa 0.7 % + 1 ma 3.0 % + 5 ma (3 to 10.9) A (45 to 100) Hz 100 Hz to 0.09 % + 2 ma 0.15 % + 2 ma 3.2 % + 2 ma (11 to 20.5) A (45 to 100) Hz 100 Hz to 0.2 % + 5 ma 0.2 % + 5 ma 3.7 % + 5 ma Parameter/Equipment Range CMC 2, 4 ( ) Comments Capacitance Generate LCR Meter & Multimeters (220.0 to 399.9) pf (0.4 to 1.09) nf (1.1 to 3.29) nf (3.3 to 10.9) nf (11 to 32.9) nf (33 to 109.9) nf (110 to 329.9) nf (0.33 to 1.09) μf (1.1 to 3.29) μf (3.3 to 10.9) μf (11 to 32.9) μf (33 to 109.9) μf (110 to 329.9) μf (0.33 to 1.09) mf (1.1 to 3.29) mf (3.3 to 10.9) mf (11 to 32.9) mf (33 to 110) mf 4.0 % + 10 pf 1.8 % nf 0.90 % nf 0.40 % nf 0.67 % nf 0.41 % nf 0.40 % nf 0.40 % µf 0.40 % µf 0.40 % µf 0.60 % µf 0.64 % µf 0.42 % + 1 µf 0.64 % mf 0.42 % mf 0.60 % mf 0.90 % mf 0.64 % mf (A2LA Cert. No ) Revised 07/11/2018 Page 6 of 11

7 Parameter/Range Frequency CMC 2, 4 ( ) Comments Inductance Generate LCR Meter & Multimeters, Fixed Points 1 mh 10 mh 100 Hz, 120 Hz, 100 Hz, 120 Hz, 2 µh 13 µh Quad Tech series 100 mh 100 Hz, 120 Hz, 210 µh 1 H 100 Hz, 120 Hz, 1.3 mh Parameter/Equipment Range CMC 2, 4 ( ) Comments Oscilloscopes Level Sine Wave Flatness - Bandwidth 250 khz to 1 GHz 1.5 Hz Agilent E4400B DC Signal 50 Ω Load 1 MΩ Load (-6.6 to 6.6) V (-130 to 130) V 0.25 % + 40 µv 0.06 % + 40 µv Square Wave 50 Ω Load (-6.6 to 6.6) V 10 Hz to 10 khz 0.3 % + 40 µv 1 MΩ Load (-130 to 130) V 10 Hz to 10 khz 0.1 % + 40 µv Level Sine Wave Amplitude (50 khz Reference) 50 khz to 100 MHz (100 to 300) MHz (300 to 600) MHz 2.0 % µv 2.5 % µv 5.0 % µv Time Marker 2 ns to 20 ms 50 ms to 5 s 8 μs/s 0.8 % + t * 0.1 % t = time in seconds Power Level (-136 to 13) dbm 0.12 dbm HP 436A, 8447D, 8482A (A2LA Cert. No ) Revised 07/11/2018 Page 7 of 11

8 Parameter/Equipment Range CMC 2, 4 ( ) Comments Electrical Calibration of RTD Indicator Measuring Instruments 100 (-200 to 800) C (-328 to 1472) F 0.3 C 0.55 F Fluke 525B Electrical Simulation of Thermocouple Indicator Measuring Instruments Type J (-210 to 1200) ºC 1.3 C Fluke 525B Type K (-270 to 1370) ºC 1.3 C Type T (-270 to 400) ºC 0.7 C IV. Mechanical Parameter/Equipment Range CMC 2 ( ) Comments Scales & Balances (0.25 to 300) lb (1 to 4000) g 0.04 lb 530 mg NIST Class F weights 1 mg to 750 g 1.5 mg Troemner Ultra Class (better than ASTM E Class 1) weights Accelerometers (5 to < 100) Hz (100 to 2000) Hz 4.5 % 4.5 % TMS 9200D with PCB301A11 (> 2000 to ) Hz 5.5 % Endevco 28959F with PCB301A11 Force Tension & Compression (0 to 300) lbf 0.04 lbf NIST Class F deadweights (0 to 1000) lbf 3.0 lbf Load cell (A2LA Cert. No ) Revised 07/11/2018 Page 8 of 11

9 Parameter/Equipment Range CMC 2, 4 ( ) Comments RPM Calibration of Tachometer (20 to ) RPM 1.3 RPM Ametek 1965 Torque Torque Cell & Transducer (5 to 3000) in lbf 0.02 % NIST Class F deadweight & load arm Torque Meter 3 (5 to 1200) in lbf (10 to 100) ft lbf (100 to 1000) ft lbf 0.6 % 0.6 % 0.6 % Torque transducer Pressure Measuring Equipment Hydraulic Up to 1000 psi Up to 5000 psi 0.05 % 0.12 % HPC41-1kPSI Crystal 5KPSIXP2i Pneumatic (0 to 300) psi 0.01 psi DPI 611 Vacuum (0 to -14.5) psi 0.01 psi DPI 611 Indirect Verification of Rockwell Hardness Testers HRC: (20 to 30) HRC (35 to 55) HRC (59 to 65) HRC 1.3 HRC 1.3 HRC 0.8 HRC Hardness block, indirect verification per ASTM E18:2005 HRBW: (40 to 50) HRBW (60 to 79) HRBW (80 to 100) HRBW 1.5 HRBW 1.5 HRBW 1.4 HRBW HRC30N: (40 to 50) HRC30N (55 to 73) HRC30N (75 to 80) HRC30N 1.5 HRC30N 1.5 HRC30N 1.1 HRC30N HRB30T: (43 to 56) HRB30T (57 to 70) HRB30T (70 to 82) HRB30T 1.9 HRB30T 1.4 HRB30T 1.4 HRB30T (A2LA Cert. No ) Revised 07/11/2018 Page 9 of 11

10 V. Thermodynamics Parameter/Equipment Range CMC 2 ( ) Comments Temperature Measure Type J (-80 to 300) ºC 1.3 C Fluke 525B Type K (-80 to 300) ºC 1.3 C Type T (-80 to 300) ºC 0.7 C Temperature Measure (-80 to 300) C 0.1 C Fluke 1552A-Ex Relative Humidity Measuring Equipment, Fixed Points 11.3 % RH 33 % RH 75.4 % RH 97.5 % RH 1.7 % RH 1.7 % RH 2.2 % RH 2.8 % RH Vaisala humidity & temperature meter standard & salt solutions Relative Humidity Measure (11 to 95) % RH 1.4 % RH Vaisala NM w/ probe HMP75 VI. Time & Frequency Parameter/Equipment Range CMC 2 ( ) Comments Frequency Measuring Equipment (0.01 to 119.9) Hz (120.0 to ) Hz (1.20 to 11.9) khz (12.00 to 119.9) khz (120.0 to ) khz (1.20 to 2.00) MHz % + 5 µhz % + 5 µhz % + 5 µhz % + 5 µhz % + 5 µhz % + 5 µhz Frequency Measure 0.1 Hz to 225 MHz 250 mhz HP 53131A Time Measure (0 to 10) s 4.7 ns HP 53131A (A2LA Cert. No ) Revised 07/11/2018 Page 10 of 11

11 1 This laboratory does not offer commercial calibration service 2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer s device and to influences from the circumstances of the specific calibration. 3 In the statement of CMC, % is read as a percentage of reading unless otherwise noted. 4 The stated measured values are determined using the indicated instrument (see Comments). This capability is suitable for the calibration of the devices intended to measure or generate the measured value in the ranges indicated. CMCs are expressed as either a specific value that covers the full range or as a fraction/percentage of the reading plus a fixed floor specification. (A2LA Cert. No ) Revised 07/11/2018 Page 11 of 11

12 Accredited Laboratory A2LA has accredited APTIV CONTRACT SERVICES S. DE R. L. DE C. V.CALIBRATION LAB Chihuahua, MEXICO for technical competence in the field of Calibration This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This laboratory also meets R205 Specific Requirements: Calibration Laboratory Accreditation Program. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 13 th day of December President and CEO For the Accreditation Council Certificate Number Valid to November 30, 2019 Revised July 11, 2018 For the calibrations to which this accreditation applies, please refer to the laboratory s Calibration Scope of Accreditation.