PRODUCTS CATALOGUE SAFETY

Transcription

1 PRODUCTS CATALOGUE SAFETY

2

3 Safety light Curtains Basic theory Safety light Curtains: characteristic elementsnduttivi. Light Curtains are electro sensitive devices using one or more light beams, emitted by an Emitter and received by a Receiver, to create an intangible controlled area. Fundamental characteristics are: Safety type Defines the self-monitoring and safety principles contained in the device It must be chosen as a function of the risk level characterising the machine When the chosen safety device is a photo-electric barrier (AOPD Active Optoelectronic Protective Device), it shall necessary belong to TYPE 2 or TYPE as established by the International Standard IEC Why Type and not Category? When talking about light curtains and laser scanners, we normally refer to their safety type ; while for all other safety devices the term of choice is safety category. This distinction is due to the International Standard IEC 6196, in which the term type is introduced to determine the safety level of optoelectronics protective equipment. In practice, type adds some optical requirements to the requirements which define categories for non-optical safety devices. Therefore, a Type 2 light curtain is a light curtain which complies with the requirements for category 2 safety electronics and furthermore whose beams have certain characteristics, among which a given aperture angle, immunity to light interference and so on. The same applies for Type light curtains and Type laser scanners. Resolution Minimum size of an object that, placed into the controlled area, will obscure the controlled zone and hence stop the hazardous movement of the machine. Single beam light barriers: their resolution R is the same as the diameter of the lens. R = D Multibeam light curtains: their resolution R is the same as the sum of the lens diameter + the distance between two adjacent lenses. R = P + D moving object A D R = D R D R = P + D R : resolution D : beam pitch P : lenses A : optical axis R = D R : D : A : resolution lens diameter optical axis P A Protected height This is the height controlled by the light curtain. If it is positioned horizontally, this value shows the depth of the protected zone. R = P+D L : H : protected area lengh protected area height L Range This is the maximum working distance that may exist between the Emitter and the Receiver. When deflection mirrors are used, it is necessary to take into account the attenuation factor introduced by each of them, which it is about 15%. H Response Time This is the time it takes for the light curtain to transmit the alarm signal from the time the protected zone is interrupted. Basic theory

4 Advantages of light Curtainsi induttivi. Effective protection in the event of fatigue or distraction of the operator. Increase in the productive capacity of the machine as the light curtain does not require the manual handling of physical guards or waiting for them to open. Faster machine loading/unloading operations. Reduced times of approach to the working areas. Elimination of the risk of tampering since any irregular intervention on the light curtain stops the machine. Simple and quick installation, with greater flexibility of adjustment on the machine, even in the case of subsequent repositioning. Possibility to build up large sized protections, either linear or along a perimeter, on several sides, at greatly reduced costs. Facilitated and fast maintenance of the machine, as there is no need to remove physical guards, such as grids, gates, etc. Improved appearance and ergonomic effectiveness of the machine. Condition of usenduttivi. For the photoelectric safety protections to be effective, it is necessary to verify that: It must be possible to electrically interface them to the control unit of the machine. The time taken to reach the hazardous point must be greater than the time necessary to stop the hazardous movement. The machine must not create secondary dangers due to the projection or fall from above of materials. If this danger exists, additional protections of a mechanical nature have to be provided. The minimum size of the object to be detected must be equal to or greater than the chosen light curtain resolution. Selection criteria of a safety light curtain induttivi. Definition of the zone to be protected. Definition of the parts of the body to be detected: - fingers or hands; - approaching body of a person; - presence of a person in a hazardous area. Definition of the safety distance between the light curtain and the hazardous point. Definition of the safety category Level/Type to be adopted according to ISO 189-1, IEC 62061, IEC Definition of the zone to be protectedduttivi. Take into account the configuration of the zone: - shape and dimensions: width and height of the access area; - positions of hazardous parts; - possible access points. The light curtain must be positioned so as to prevent the access to the dangerous area from above, from below, and from the sides without having. intercepted the field protected by the light curtain. It is possible to install one or more deflection mirrors in order to protect areas with access from several sides. This results in a considerable reduction in costs, as this solution eliminates the need of installing many separate light curtains. Basic theory

5 Definition of type of detection detection characteristics advantage finger or hand Detection necessary when the operator must work close to the danger. Barrier resolution must be between 1 mm and 0 mm. Possibility to lower the dimensions by reducing at the top the space between the protection and the dangerous zone. Short time for machine charging and discharging. Less operator fatigue, more productivity. body (use as trip device) Ideal detection for access control and protections of several sides, also for long scanning distances. The barrier must be placed at least at 850 mm from the danger. Protection costs reduced by the restricted number of beams. Possibility to protect zones with big dimensions by using deflection mirrors. Barrier normally composed by 2,, beams. see note below presence in a dangerous zone Detection realized by positioning the light curtains horizontally to control continuously the presence of an object in a definite zone. The light curtains resolution depends on the height of the detection plane, anyway it cannot be higher than 116 mm. Possibility to control zones not visible from where the machine s push button controls are located. Note Accidental start-up of the machine shall not be possible when anyone crosses the sensitive area and stays undetected in the dangerous area. Suitable ways of eliminating this type of risk include the following: Use of start / restart-interlock function positioning the command so that the dangerous area is in full view and so that the command cannot be reached by anyone from inside the dangerous area. The Restart command has to be safe in compliance with IEC Use of additional presence sensing detectors for the detection of the operator inside dangerous area Use of obstacles preventing the operator from remaining undetected in the space between the sensing zone of the protective device and the dangerous area. Basic theory 5

6 Determination of the safety distanceduttivi. The effectiveness of the protection depends greatly on the correct positioning of the light Curtain with respect to the danger. The light Curtain must be located at a distance greater than or equal to the minimum safety distance S, so that reaching the dangerous point will be possible only when the dangerous action of the machine has been stopped. The light Curtain must be positioned so that: It is impossible to reach the dangerous point without going through the zone controlled by the light curtain A person cannot be present in the dangerous zone without his/her presence being detected. To this end, it might be necessary to resort to additional safety devices (i.e..: photoelectric light curtains arranged horizontally). European Standard EN ISO 1855 provides the elements for the determination of the safety distance. If the machine in object is governed by a specific C type Standard, it shall be taken into two account. If the distance S determined in this manner is too big, it is necessary: a) to reduce the total stopping time of the machine, b) to improve the detection capability (resolution) of the light curtain. dangerous area dangerous area S S One-side protection Three-side protection using deflection mirrors i. General formula for the determination of the minimum safety distance S = K x T + C S K T C minimum safety distance between the protection and hazardous point, expressed in mm speed of approach of the body or parts of the body, expressed in mm / sec total stopping time of the machine, consisting of: t1 reaction time of the protective device in seconds t2 reaction time of the machine in seconds, until it stops the hazardous action. additional distance in mm C takes into account: Possible intrusion of parts of the body in the sensitive area before they are detected. For example: C = 8 x (d-1) if D (light Curtain resolution) 0 mm. C = 850 if D (light curtain resolution) > 0 mm and for 2,, beams Curtains. C = 1,200 - (0, x H) for horizontal light Curtains. The dangerous point can be reached by leaning over the upper edge of the sensitive area of a vertical light Curtain. In this case C, called CRO is obtained from the following Table 2 of EN ISO 1855 / EN 999. Basic theory 6

7 altezza height of altezza height b del b bordo of upper superiore edge of della area zona protected protetta by photoelectric della barriera fotoelettrica Curtain (mm) (mm) della Hazard zona pericolosa zone a a (mm) (mm) 900 1, , , , , , , , , , , alternative distanza aggiuntiva distance CRO CR , , , , , , , , , , , , , , , , , , , , , , , , , (Tab.2 ISO 1855/EN 999) Interpolation is not allowed. If distances a, b or CRO fall between values listed in the table, use the higher. CRO (reaching over) calculated using Table 2 of EN ISO 1855 / EN 999 must be compared to C as conventionally calculate (see paragraph 1). Always select the higher value. For combined mechanical and electrosensitive protections (as shown), where it would be possible to lean against the mechanical protection and bypass the light curtain, for the calculation of the parameter C should use the Table 1 (for low risk applications) or the Table 2 (for high-risk applications) of ISO 1857:2007 (formerly EN 29) in place of the table on the previous page. In this catalog the two tables of ISO 1857:2007 (formerly EN 29). Safety distances to prevent danger zones being reached by upper and lower limbs - are not mentioned. 1 Dangerous area 2 Reference plane Light Curtain 1 Dangerous area 2 Reference plane Light Curtain Mechanical protection Basic theory 7

8 Direction of approach perpendicular to the protected plane with α = 90 (± 5 ) induttivi. Light Curtains with resolution for the detection of hands and fingers. Light Curtains resolution (d) 0 mm D 0 S dangereous area The distance S must not be lower than 100 mm H P S = 2,000 xt + 8x (d-1) if the formula as a result: S > 500 you can use K = 1,600 If the distance S is greater than 500 mm it is possible to re-calculate the distance using K =1,600 In these circumstances, the distance must in no case be S = 1,600 xt + 8x (d-1) lower than 500 mm Light curtains with a resolution for detection of arms and legs. 0 mm < Light curtains resolution (d) 70 mm 0 < D 70 S dangereous area S= 1,600 xt The height of the lowest beam must be equal to or lower than 00 mm The height of the uppest beam must be equal to or higher than 900 mm Light grids for body detection through access control. Light Curtains resolution (d) >70 mm D > 70 dangereous area P P P2 P1 S= 1,600 xt Number and height of the beams N. Recommended height 2, mm, ,100 mm, ,200 mm H Basic theory 8

9 Direction of approach parallel to the protected plane with α = 0 (± 5 ) Horizontal light curtains for presence control in a dangerous area C = 1,200 - (0. x H) must be equal to or greater than 850 mm. The maximum height allowed S is: Hmax = 1,000 mm. The height H depends on the re- dangereous area solution d of the light curtains and is determined through the following formula: H = 15 x (d - 50). H S=1,600 xt + (1, xh) This formula can also be used to determine the maximum resolution that can be used at the different heights d = H / For example, the maximum resolution limits will be: for H = 1,000 mm d = 116 mm for H = 0 mm d = 50 mm If H is greater than 00 mm, at the stage of risk assessment it becomes necessary to take into consideration the possibility of access from beneath the beams. Direction of approach angled to the protected plane with 5 < α < 85 nduttivi. Slanted light Curtains to detect hands and arms and for presence control in the dangerous area. With angle a > 0 refer to dangereous area S the case of approach perpendicular to the protected plane. (Previous case) With α > 0 : The distance S refers to the beam farthest away from the hazardous point. P 0 H With angle a < 0 refer to the case of approach parallel to the protected plane (cases of previous page) The height of the beam farthest away from the hazardous point must not be greater than 1,000 mm. For the determination of height H or resolution d apply the following formulas to the lowermost beam: H = 15 x (d - 50) d = H / Basic theory 9

10 Muting functioninduttivi. The Muting function is the provisional and automatic cut-out of the light curtain protective function in relation to the machine cycle. Muting can only occur in a safety condition. Two types of applications are envisaged: 1. Enabling personnel access inside dangerous area during the non-dangerous part of machine cycle Positioning or removal of workpiece Depending on the position of the tool, which is the most dangerous part, one of the two curtains (the one facing the tool working area) is active whereas the other is in Muting mode to enable the operator to load/unload the workpiece. Muting mode of the light curtains is subsequently reversed when the tool works on the opposite side of the machine. 2. Enabling access to material and preventing access to personnel Pallet exit from dangerous area The safety light curtain incorporates Muting sensors able to discriminate between personnel and materials. Only the material is authorized to pass through the monitored area. The essential requirements regarding the Muting Function are described by the followings Standards: IEC TS 6206 application of the protective equipment to detect the presence of persons EN 15- Safety of the Machinery - automatic palletizing systems IEC Electro-Sensitive Protective Equipment General Requirements Muting is a temporary suspension of the safety related function and it must be activated and de-activated automatically. The safety integrity level of the circuit implementing the Muting function shall be equal to that of the safety function temporarily suspended, so that the protection performance of the entire system is not adversely affected. Muting should be activated and de-activated only by means of two or more separate hardwired signals triggered by a correct time or space sequence. It shall not be possible to trigger Muting while the ESPE outputs are in the off state. It shall not be possible to initiate Muting by turning the device off and then on again. Muting shall be only activated in an appropriate point of the machine cycle, i.e. only when there is no risk for the operator. Muting sensors shall be mechanically protected to prevent mismatch in case of impact. Muting: palletizers and materials handling systems Requirements for the monitoring of the openings Monitor the load, not the pallet, otherwise the operator might go into the hazardous zone being dragged by the pallet. Muting time must be restricted to the actual time taken by the material to pass through the opening. Muting must be time-restricted. Sensor mismatch with effect similar to their actuation shall not allow a condition of permanent Muting. The configuration and positioning of the Muting sensors shall ensure reliable differentiation between personnel and material. The layout of the opening, the positioning of the Muting sensors and the additional side protections shall prevent personnel access to the dangerousarea for all the time the Muting function is activated and throughout the time the pallet crosses the opening. Therefore it is necessary to realise a safety system able to distinguish between: authorized materials non authorized people to go through the light curtain The Muting function can be present on both Type 2 and Type Safety light Curtains. Basic theory 10

11 Common solutions for Muting sensor positioning Muting with 2 crossed-beam sensors Configuration type T with timing monitoring and two-way pallet operation: The point of intersection of the two beams shall lie in the segregated dangerous area beyond the light curtain. A fail safe timer shall be provided to restrict Muting to the time needed for the material to cross the opening. The Muting function shall be activated only if the Muting sensors are contemporaneously intercepted: (t2(s2) t1(s1) = seconds max.). The two beams shall be continuously interrupted by the pallet throughout the transit through the sensors. A matt cylindrical object D=500 mm (simulating the size of a human body) shall not trigger the Muting function. S1 S2 AREA DANGEREOUS PERICOLOSA AREA X Mechanical safety guard Muting sensor beam intersection shall be positioned the higher up or equal than level of the lower light curtain beam to avoid possible tampering or accidental triggering of Muting. Muting with parallel-beam sensors Configuration type T with timing and/or sequence monitoring Two-way pallet operation: The Muting sensors shall be all actuated together for a brief moment (sequential actuation and de-activation of the sensors). The distance between sensors and the sensing field of the light curtain shall be: d2 a AODP S1 S2 S S dl and d < 200 mm AREA PERICOLOSA AREA DANGEROUS PERICOLOSA AREA To prevent undetected personnel access by preceding or following immediately after the pallet during Muting. d2 > 250 mm b To prevent personnel limb, garment, etc. from enabling Muting by triggering two sensors simulta- d1 d neously. Mechanical safety guard Muting with 2 crossed-beam or parallel-beam sensors Configuration type L with timing monitoring and oneway only (exit from dangerous area) pallet operation: AREA PERICOLOSA DANGEROUS AREA S1 S2 Muting sensors shall be positioned beyond the light curtain in the dangerous area. Muting shall be disabled as soon as the light curtain is cleared and not later than seconds max. from the instant the first of the two Muting sensor is cleared. The timer monitoring the seconds shall be a safety-related item. Mechanical safety guard Basic theory 11

12 Possibe functions associated with Muting are: Muting sequence: in case Muting inputs are not activated within the right temporal sequence Muting function is excluded. Maximum Muting Time-Out: if barriers remains in Muting condition longer than the prefixed time muting function is automatically stopped. Override function: if a wrong muting sequence occures or any material remains blocked inside protected area it s not possible to restart the machine. Override function allows emergency forced temporary restart of the machine by activiating a dedicate signal on the barrier. That allows to free the control area from the obstacle. Blanking functionnduttivi. Blanking is an auxiliary function of safety light curtains for which the introduction of an opaque object inside parts of the light curtain s protection field is allowed without causing the stoppage of the machine. Blanking is only possible in the presence of determined safety conditions and in accordance with a configurable operating logic. The blanking function is therefore particularly useful when the light curtain s protection field must be inevitably intercepted by the material being worked or by a fixed or mobile part of the machine. In practice, it is possible to keep the light curtain s safety outputs in an ON condition, and the machine working, even if a pre-determined number of beams within the protection fields are being intercepted. Fixed Blanking allows a fixed portion of the protection field (i. e. a fixed set of beams) to be occupied, while all the other beams operate normally. Floating Blanking allows the object to move freely inside the light curtain s protection field occupying a given number of beams, at the condition that the occupied beams are adjacent and that their number is not higher than the configured one. Floating Blanking with compulsory object presence makes the light curtain work in a reverse way within the blanked portion of the protection field. That is, the blanked beams must be occupied during blanking and therefore the object has to be inside the protection field for the light curtain to remain in the ON state. In this case too the object can move freely within the protection field if the above conditions are respected. Requirements for the blanking function can be found in the Technical Specification IEC/TS 6206 describing additional means that may be required to prevent a person from reaching into the hazard through the blanked areas of the detection zone. Warning The use of the blanking function can be allowed depending on the characteristics of the application to be protected. Based on the risk analysis of your application, check whether the use of the blanking function is allowed for that particular application and with what features. M.D. does not assume responsibility for the improper use of the blanking function nor for the possible damages deriving from it. The use of the blanking function may need a recalculation of the safety distance due to the modified detection capability. Minimum distance from reflecting surfacesuttivi. The optical beams of the projector, having a beam angle that is not null, can partly be diverted by reflective surfaces located near to the safety light curtain. This may mean that a break in the direct path of the optical beam is not detected, which is why all reflective surfaces and reflective objects (in any position they may have with respect to the controlled area, above, under, inside or outside) must respect a minimum distance from the direct path of the beams of the Safety light Curtain. DANGEROUS ZONE S D A E E Emitter R Receiver D minimum distance S reflective surface A aperture angle P operatig distance Safety light Curtains respect the maximum beam angle defined by IEC / EN The safety distance D is calculated considering the entire beam angle and the safety light curtain reciprocally orientated towards the reflective surface by an angle a, in this way we consider the case of alignment at the limit of reciprocal visibility between the emitter and receiver, but which is more dangerous due to the effects of the reflection. For ranges less than m the value calculated at m applies: D = tan(a) * P/2 For P m the safety distance D to take is calculated as follows: Type 2: A = 10 tan(a) = Type : A = 5 tan(a )= Basic theory 12

13 The following chart shows minimum distance from reflective surface for Type 2 and Type safety light curtains with a maximum operating distance of 10 m. D TYPE 2 minimum distance from reflective surface (mm) optical axis TYPE L operating distance L between Emitter and Receiver (m) Instructions for component installation The angular opening of a safety light curtain is extremely narrow (±5 for Type 2 and ±2,5 for Type ), therefore the alignment procedure must be carried out with great care: The brackets must make it possible to position both the emitter and the receiver, and at the same time they must be strong enough to maintain the alignment under working conditions. Furthermore, remember that eventual vibrations or shock could misalign the Safety light Curtain. If beam deflecting mirrors are used, it is necessary to keep in mind that the alignment procedure will be more difficult. As a matter of fact, considering that each mirror will involve a capacity reduction of about 15% (depending on the quality of the mirror) and that the mirror brackets may not be particularly steady, the system will be easily misaligned (for example when trying to clean the mirror). The presence of shiny or reflective surfaces can cause the safety light curtain to be ineffective. It is therefore necessary to position the safety light curtain at a suitable distance from any reflective surfaces. Any control unit which does not provide at least an IP5 protection degree must be installed within a switchboard, in order to guarantee this minimum protection. The safety light curtain must be positioned so as to avoid anyone accidentally leap frogging it. When determining the minimum distance at which the safety light curtain must be positioned in the danger area, it is necessary to take into account. the safety light curtain s response time and the machine s shutdown time, as previously described. The start-up or restart-up devices must be positioned so as to prevent the function in question from being activated by an operator within the protected area. Basic theory 1

14 Integration of the ESPE As the ESPE will be integrated in the machine safety-related control system, the choice of its safety level will depend on the result of risk analysis and, consequently, on parameters such as PL, SIL or Category resulting from this analysis. Product Standards (Type C) usually recommend the most suitable ESPE type for each safety-related function involved. If type C Standards are not available, adopt the recommendations of ISO and IEC Also consider that the overall safety integrity of the serial connection: input control unit actuators, shall necessarily be equal to or lower than that of the weaker device. Rules for correct interconnection of protection devices to machine control system The interconnections between safety outputs of ESPE (OSSD) and the machine primary control elements, the positioning and selection of reset push buttons shall not reduce or eliminate the extent of safety integrity assigned to the safety-related machine control system. Figure A shows the most common example, i.e. where the machine control and monitoring system (e.g. the PLC) has no safety-related function. In this case, the safety-related control system monitoring the protective devices connected to it must operate autonomously and must be inserted between the machine control system and the machine primary control elements. Non-safety-related input devices Protective equipment input Non-safety-related input devices output Safety-related input devices EDM MPCE Figure A MPCE = Machine Primary Control Element If the machine is equipped with an integrated safety-related control and management system (safety-related PLC), see figure B, machine operational functions and safetyrelated functions should be governed through the centralized safety-related system. Non-safety-related functions Safety-related functions e.g. restart interlock, test Protective equipment EDM input Safety-related machine control output MPCE Figure B Basic theory 1

15 Glossaryduttivi. symbol detection characteristics Warning to avoid danger! A warning indicates real or potential hazards. Its task is to indicate procedures and behaviour that can avoid accidents. Read and follow these instructions carefully. Indication Indications that can help achieve better performance. Emitter symbol This symbol identifies devices that have the function of a projector. Receiver symbol This symbol identifies devices that have the function of a receiver. Finger protection This symbol marks devices designed to detect fingers entering a protected area. It refers to safety light curtains with a resolution of 1 mm, this value enables using the minimum safety distance and therefore reducing the loading and unloading times to a minimum and the least fatigue for the operator. Hand protection This symbol marks devices designed to detect a hand entering a protected area. It refers to safety light curtains with a resolution less than or equal to 0mm; these resolutions allow safety distances compatible with short loading and unloading times and a low level of operator fatigue. Presence control This symbol marks devices designed to detect limbs entering a protected area or detect human presence in a protected area. For presence detection, with light curtains in a horizontal position, resolutions of between 50 and 116mm are to be used, the height off the ground is calculated in relation to these values. Body protection This symbol marks devices designed to detect a body entering a protected area. It refers to multi-beam safety light grids with 2, or beams. These light curtains are usually cost-effective and feature a long range, they enable creating protection for extensive areas and on more than one side, using diverter mirrors. Basic theory 15

16 notes Basic theory 16

17 features SBCR0 series Control unit Type 2 Up to 6 sets of safety photocells M18 (SH-IA) or M0 (TH6-IA) interconnectable DIN RAIL Mounting Body protection and access control Cat. 2 according to EN Cat. 2 / PL c according to EN ISO 189-1; SIL CL 1 acording to EN / IEC Models with single/double channel Muting and Override functions Response time less than 5 ms 2 OSSD outputs Control unit Type 2 download area Application notes Photos Catalogue / Manuals code description SBCR0 / S - A 0 series power supply inputs type SBCR0 S A 0 M Safety control unit for safety photocells Tensione di alimentazione 2 Vcc Suitable for safety photocells Standard model Muting/Override model connectable devices series barriera / photocell reticolo ottico distanza operating distance operativa models modelli SH - IA M18 fino until a 10 m SH - IA TH6 - IA M0 fino until a 60 m TH6 - IA SBCR0 17

18 technical specification according to IEC EN SBCR0/S-A0 SBCR0/S-AM tensione power di alimentazione supply tolerance tolleranza on alimentazione power supply ondulazione voltage ripple residua corrente absorbed assorbita current 2 Vdc Vcc % 5 Vpp 100 ma Safety solo Guardia function available funzioni disponibili functions START / RESTART Avvio/Riavvio / INTERLOCK 125 ms 125 ms EDM (con EDM monitoraggio (00 ms relay dei switching tempi di commutazione, time monitoring) 00ms) - muting - doppio double muting - override sequenza muting sensori sequence di Muting verifica muting durata Time-Out max. Muting - - s (funzione (selectable) escludibile) min (funzione (selectable) escludibile) muting tipo sensori sensors Muting type uscite muting lampada di output Muting uscita status lampada output di stato caduta output di tensione voltage drop in uscita tempo response di risposta time tempo recovery di ripristino time grado IP di protection protezione IP operating limiti di temperatura temperature temperatura storage di immagazzinamento temperature materiale housing contenitore material peso approssimativo weight - x PNP, NO - 2 lamps 2 lampade, 1 to 10 W, da from 1 a 10 1 to W, 102 W, Vcc 2 Vcc - da from 1 a 101 to W, 102 W, Vcc 2 V Vdc VVcc 2.5 2,5 a 500 ma 5 ms 100 ms IEC IP20 to (installare be mounted all interno inside di a un cabin quadro with con IP5 grado minimum minimo IP5) C C ABS UL VO 70 g safety parameters Category 2 safety control modelli unit SBCR0 safety integrity level Type performance level maximum frequency of request () PFH d () TM (life time) SIL (IEC 61508), SIL CL (EN 62061) (1) (EN ISO 189) (1) PL e (EN ISO 189) (1) 60/min (EN ISO 189) 8.1 x years 18

19 electric diagrams of the connections Muting sensors Muting lamps state lamps TEST button start/restart button override button LAMP1 LAMP2 STATE LAMP SBCR0 OSSD2 OSSD1 supply contactors EDM chain sensors 1 chain sensors 2 Muting conditions n of Muting sensors Muting signals combinations 2 M1 & M2 M followed by M1& M2 (direction recognition) 2+2 M1 & M2 and/or M & M M1 M2 muting is indipendent from M M Muting conditions and Muting sequence control n of Muting sensors Muting signals combinations 2 M1 & M2 must be active within s M1 & M2 must be active within s (with M is active) 2+2 M1 & M2 and / or M & M must be active within s Muting sequence of M1 M2 is indipendent from Muting sequence of M M SBCR0 19

20 dimensions (mm) SBCR0/**-**-** SBCR0 20

21 SH-IA/IC e TH-IA/IC series Photocells Type 2 and Type features M18 Models 10 m (axial optic) and 5 m (radial optic) operating distance M0 models 60 m operating distance EN50100 Category 2 and Category compliant LED indicators Plastic and Metal Housing Inputs and Outputs IEC compliant and adaptable with any safety module To be used together with a Category 2 or Category safety control unit to obtain a safety system EN ISO 189 compliant download area Application notes Photos Catalogue / Manuals Photocells Type 2 and Type code description (SH series) SH 2 / E - 0 E IC series type model housing connection logic SH 2 E R E K IC IA M18 safety photocell Type 2, 12 khz modulation Type 12 khz modulation Emitter unit Receiver unit Plastic housing, axial emission Metal housing, axial emission Plastic housing, radial emission Metal housing, radial emisison M12 connector output M12 radial connector output Emitter Test Input Logic H = light L = dark, Receiver Output Logic: H = light, L = dark Emitter Test Input Logic L = light H = dark, Receiver Output Logic: L = light, H = dark code description (TH series) TH 2 / E - K IC series TH M0 safety photocell type 2 6 Type 2, 12 khz modulation Type, 12 khz modulation model E R Emitter unit Receiver unit connection K M12 radial connector logic IC IA Emitter Test Input Logic H = light L = dark, Receiver Output Logic: H = light, L = dark Emitter Test Input Logic L = light H = dark, Receiver Output Logic: L = light, H = dark SH-IA/IC TH-IA/IC 21

22 available models (Type 2) series diameter emission optic operating distance (m) connection housing unit model SH2 M18 red Type 2 axial 10 Type 2 radial 5 Type 2 axial 10 Type 2 radial 5 M12 axial plastic metallic Emitter Receiver Emitter Receiver Emitter Receiver Emitter Receiver SH2/E-0EIC SH2/R-0EIC SH2/E-2EIC SH2/R-2EIC SH2/E-1EIC SH2/R-1EIC SH2/E-EIC SH2/R-EIC Type 2 axial TH2 M M12 radial plastic metallic Emitter Receiver Emitter Receiver Emitter Receiver SH2/E-0KIC SH2/R-0KIC SH2/E-1KIC SH2/R-1KIC TH2/E-KIC TH2/R-KIC available models (Type ) series diameter emission optic operating distance (m) connection housing unit model Emitter SH/E-0EIC Type axial 10 plastic Receiver Emitter Receiver SH/R-0EIC SH/E-0EIA SH/R-0EIA Type radial 5 Emitter Receiver SH/E-2EIC SH/R-2EIC M12 axial Emitter SH/E-1EIC SH M18 red Type axial 10 Type radial 5 metallic Receiver Emitter Receiver Emitter Receiver SH/R-1EIC SH/E-1EIA SH/R-1EIA SH/E-EIC SH/R-EIC 10 plastic Emitter Receiver Emitter SH/E-0KIA SH/R-0KIA SH/E-1KIA type axial TH6 M0 60 M12 radial metallic Receiver Emitter Receiver Emitter SH/R-1KIA TH6/E-KIC TH6/R-KIC TH6/E-KIA SH-IA/IC TH-IA/IC Receiver TH6/R-KIA 22

23 technical specifications type 2 and type according to EN/IEC /2 SH axial SH radial TH nominal operating distance Excess Gain = 2 nominal operating distance Excess Gain = model spot diameter minimum detectable object emission Effective Aperture Angle (EAA) power supply current comsumption output current emission wavelength standard modulation frequency supply voltage UB residual ripple HIGH level output LOW level output reaction time receiver output per transaction LIGHT / DARK reaction time receiver output per transaction DARK /LIGHT response time of safety LOW input Test projector HIGH input Projector test test input LOW level (Emitter) electrical protection class mechanical protection working temperature storage temperature m m m m m m M18 M ø 15 mm red typical 1.8 ; ± 2, Vdc 25 ma (emitter); 25 ma (receiver); 22 ma (typical, light mode) 50 ma; 70 ma max 660 nm 12 KHz 19.2 V...28 V 5 V U B -.2 V... U B V (typical) 5 V ø 2 mm 200 µs, from front to LOW DARK models for IC, to HIGH for models IA 00 µs, from front to LIGHT UP models for IC, LOW models for IA it would depend on the security utility < 5 V IC output inactive ; model IA active issue vin test >> 15 V IC output active ; model IA issue inactive IC models, LOW = DARK ; HIGH = LIGHT IA models, HIGH = DARK ; LOW = LIGHT III IP67 (EN60529) -20 C C (typical + 20 C) -0 C C no load. external power supply to the devices must include a brief power failure of up to 20 ms In conformity with EN Suitable power supplies are commonly available on the market. Operation with the network short-circuit proof max. 8 A. The connections used are protected against reverse polarity. The sensors SH and TH, and the test device downstream, are connected to the same municipality and for paving ground. must not exceed or fall below of UB tolerances. the output of the sensor is normally connected to the test device, isn t an OSSD as for IEC humidity (no condensation) weight shocks 0 g (plastic); 67 g (metallic) 15%...95% 10 g; 16 ms; (IEC ) 212 g vibration 10 Hz Hz, 1 oct./min, 0.5 mm (IEC ) material Lens: Glass with PBT ring; Housing: Brass nickel-plated or PBT; M12 plug:pc Lens: Glass, aluminium; Housing: Brass nickel plated; End cap: PC; M12 plug: PBT SH-IA/IC TH-IA/IC 2

24 safety specifications (Machinery Directive 2006/2/CE) sensori Type 2 Fotoelettrici M18 and M0 M18 safety e M0 photocells di Tipo modelli 2 sensori Type Fotoelettrici M18 and M0 M18 safety e M0 photocells di Tipo modelli Type tipo 2 (IEC 6196) (1) Type tipo (IEC 6196) (1) livello di safety integrità integrity della level sicurezza SIL1 (IEC 61508), SIL CL 1 (EN 62061) (1) livello di safety integrità integrity della level sicurezza SIL (IEC 61508), SIL CL (EN 62061) (1) categoria category 2 (EN ISO 189) (1) categoria category (EN ISO 189) (1) self frequenza test frequency di test (2) (2) 100/s (EN ISO 189) livello performance di prestazione level PL e (EN ISO 189) (1) maximum frequenza frequency massima di of richiesta request () 60/min (EN ISO 189) maximum frequenza frequency massima di of richiesta request () 60/min (EN ISO 189) livello performance di prestazione level PL c (EN ISO 189) (1) PFH () d 8,1 8.1 x 10-6 () PFH d 1 x 10-6 TM TM (durata (life time) utilizzo) 20 years anni TM TM (durata (life time) utilizzo) 20 years anni (1) Only in combination with suitable test devic (2) The test rate must not be exceeded () Between two requests for a safety-related reaction from the device, at least 100 internal or external tests must be undertaken () Average probability of failure per hour, due to a serious error electrical diagrams of the connections M12 emitter M12 receiver BK (Test) BU (-) BK (OUT) BU (-) BN brown BN (+) 1 2 WH (NC) BN (+) 1 2 WH (NC) BU BK WH blue black white 2 sensors caascade connection example 2 Vdc 0 Vdc OUT TEST TEST OUT OUTPUT T INPUT The pairs remote, comprise an emitter and a receiver connected in a chain, that are running the repeater function, must be homogeneous, that is composed of an emitter and a receiver both with the same logic of Test and Exit (both type IC or IA). Couples connected to the test unit must obviously be chosen logically compatible with that unit. It should not exceed a maximum of three pairs of sensors in the chain. If you use more than one pair of monitoring sensors connected in the chain, it must always be strictly observed that the angle of propagation / reception angle of a pair of sensors does not interfere with the other of the same chain. If you use more than one pair of monitoring sensors connected to the same unit and this unit does not use a scanning procedure of the pairs it must be strictly observed that the angle of propagation / reception angle of a pair of sensors does not interfere with the other the same unit. If it takes more units it is possible that pairs of the different units may interfere, in this case the phase of test can fail causing blockages or sporadic system. Only in this case, to avoid interference it is possible to use models with different modulation frequency. SH-IA/IC TH-IA/IC 2

25 dimensions (mm) plastic housing dimensions (mm) metal housing SH2()/*-0EIC(IA) SH2()/*-2EIC(IA) SH2()/*-1EIC(IA) SH2()/*-EIC(IA) M12 x 1 M12 x 1 M12 x 1 M12 x 1 M18 x M18 x M18 x M18 x dimensions (mm) metal housing SH2()/*-*KIC(IA) M12 x M18 x 1 1 LED SH-IA/IC TH-IA/IC 25

26 dimensions (mm) metal housing TH2(6)/*-1KIC (IA) M12 x M0 x LED SH-IA/IC TH-IA/IC 26

27 features LS2, LS2_K, LS2_H series Light Curtains Type 2 according to IEC and 2 Compact housing (28 x 0 mm) and no dead zone on cap side Resolution 0, 0, 50, 90 mm for hand protection and presence control and 2,, beams for body protection/access control Controlled distance up to:,,10, 12 m Base, Standard versions and Master, Slave version to connect up to sets in cascade configuration Selectable Automatic/Manual Restart and EDM integrated functions (Standard models) Selectable controlled distance IP69K protection models (LS2_K) and models with integrated heating system to reach -25 C operating temperature (LS2_H) Standard M12 da 5 and 8 poles connectors download area Light Curtains Type 2 Application notes Photos Catalogue / Manuals code description series E/R beams area model 015 LS2 ER A 0B 0C B M S F Type 2 Safety light Curtains 28 x 0 mm compact housing Emitter / Receiver couple Light grid, 0 mm resolution, hand protection Light grid, 0 mm resolution, hand protection Light grid, 50 mm resolution, presence control Light grid, 90 mm resolution, presence control 2 beams; body protection, 500 mm resolution beams; body protection, 00 mm resolution beams; body protection, 00 mm resolution Protected height from 150 to 1,800 mm (light grids) Protected height 500, 800, 900 mm (multiple light beams) Standard model with selectable MANUAL/AUTOMATIC Restart and EDM functions Base model with integrated AUTOMATIC Restart Master Model with selectable functions Intermediate Slave model Final Slave model IP65 and IP67 protection, C operating temperature LS2 ER / protection K H Models in transparent cylindrical housing, IP69K, suitable for applications in the food industry. Resistance to washing with water at 100 bar, 80 C Housing in PMMA, caps in POM C with silicone seals. Brackets in stainless steel AISI 16L. Operating temperature C. Models in transparent cylindrical casing, IP69K protection, thermostated, suitable for applications in the food industry. Resistance to washing with water at 100 bar, 80 C. Housing in PMMA, POM C caps and silicone seals. Brackets in stainless steel AISI 16L. Operating temperature C. LS2; LS2_K; LS2_H 27

28 available models 0 mm resolution; 0... / m controlled distance area protected controllata height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series area protected controllata height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series LS2ER/0-015B LS2ER/0-15B ,5 LS2ER/0-015 LS2ER/0-15 LS2ER/0-015F LS2ER/0-00B LS2ER/0-00 1, ,5 LS2ER/0-15M LS2ER/0-15F LS2ER/0-15S LS2ER/0-00M LS2ER/0-00F LS2ER/0-150B LS2ER/0-150 LS2ER/0-00S 1, ,5 LS2ER/0-150M LS2ER/0-05B LS2ER/0-150F LS2ER/0-05 LS2ER/0-150S LS2ER/0-05M 1, LS2ER/0-165 LS2ER/0-05F 1, ,5 LS2ER/ LS2ER/0-05S LS2ER/0-060B LS2ER/0-060 LS2ER/0-060M LS2ER/0-060F LS2ER/0-060S available models 0 mm resolution; 0... / m controlled distance protected area response tempo di height controllata (mm) n n of raggi beams risposta time (ms) (ms) series (mm) LS2ER/0-015B LS2ER/0-075B LS2ER/ LS2ER/0-075 LS2ER/0-075M LS2ER/0-075F LS2ER/0-075S LS2ER/0-015F LS2ER/0-00B LS2ER/0-00 LS2ER/0-00M LS2ER/0-00F LS2ER/0-090B LS2ER/0-00S LS2ER/0-090 LS2ER/0-05B LSER/0-090M LS2ER/0-05 LS2ER/0-090F LS2ER/0-05M LS2ER/0-090S LS2ER/0-05F LS2ER/0-105B LS2ER/0-05S LS2ER/0-105 LS2ER/0-060B 1, ,5 LS2ER/0-105M LS2ER/0-060 LS2ER/0-105F ,5 LS2ER/0-060M LS2ER/0-105S LS2ER/0-060F LS2ER/0-120B LS2ER/0-060S LS2ER/0-120 LS2ER/0-075B 1, LS2ER/0-120M LS2ER/0-120F ,5 LS2ER/0-075 LS2ER/0-075M LS2ER/0-120S LS2ER/0-075F LS2; LS2_K; LS2_H 28

29 available models 0 mm resolution; 0... / m controlled distance available models 50 mm resolution; 0... / m controlled distance area protected controllata height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series area protected controllata height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series ,5 8.5 LS2ER/0-075S LS2ER/0-090B LS2ER/50-05B LS2ER/50-05 LS2ER/ ,5 5.5 LS2ER/50-05M ,5 9.5 LSER/0-090M LS2ER/0-090F LS2ER/0-090S LS2ER/0-105B LS2ER/50-05F LS2ER/50-05S LS2ER/50-060B LS2ER/ LS2ER/ LS2ER/50-060M , , LS2ER/0-105M LS2ER/0-105F LS2ER/0-105S LS2ER/0-120B LS2ER/50-060F LS2ER/50-060S LS2ER/50-075B LS2ER/ LS2ER/ LS2ER/50-075M , , LS2ER/0-120M LS2ER/0-120F LS2ER/0-120S LS2ER/50-075F LS2ER/50-075S LS2ER/50-090B LS2ER/0-15B LS2ER/ , LS2ER/0-15 LS2ER/0-15M LS2ER/0-15F LS2ER/0-15S LS2ER/0-150B LS2ER/ LSER/50-090M LS2ER/50-090F LS2ER/50-090S LS2ER/50-105B LS2ER/ , LS2ER/0-150M , LS2ER/50-105M LS2ER/0-150F LS2ER/50-105F LS2ER/0-150S LS2ER/50-105S LS2ER/50-120B available models LS2ER/ mm resolution; 0... / m controlled distance area protected response tempo di controllata n n of raggi beams height (mm) risposta time (ms) (ms) (mm) series 160.5,5 LS2ER/50-015B LS2ER/ ,5 LS2ER/50-015F LS2ER/50-00B LS2ER/50-00 LS2ER/50-00M LS2ER/50-00F LS2ER/50-00S , , ,5 1, ,5 LS2ER/50-120M LS2ER/50-120F LS2ER/50-120S LS2ER/50-015B LS2ER/ LS2ER/50-015F LS2ER/50-00B LS2ER/50-00 LS2ER/50-00M LS2ER/50-00F LS2ER/50-00S LS2ER/50-05B LS2ER/50-05 LS2_H LS2; LS2_K; 29

30 available models 90 mm resolution; 0... / m controlled distance available models 500 mm resolution; 0... / m controlled distance area protected controllata height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series area protected controllata height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series LS2ER/90-00B LS2ER/0A-050B LS2ER/90-00 LS2ER/0A ,5.5 LS2ER/90-00M LS2ER/0A-050M LS2ER/90-00F LS2ER/0A-050F LS2ER/90-00S LS2ER/0A-050S , , , LS2ER/90-05B LS2ER/90-05 LS2ER/90-05M LS2ER/90-05F LS2ER/90-05S LS2ER/90-060B LS2ER/ LS2ER/90-060M LS2ER/90-060F LS2ER/90-060S LS2ER/90-075B LS2ER/90-075B LS2ER/ LS2ER/ LS2ER/90-075M LS2ER/90-075M LS2ER/90-075F LS2ER/90-075F LS2ER/90-075S LS2ER/90-075S LS2ER/90-090B LS2ER/90-090B LS2ER/ LS2ER/ LS2ER/90-090M LS2ER/90-090M LS2ER/90-090F LS2ER/90-090F LS2ER/90-090S LS2ER/90-090S LS2ER/90-105B LS2ER/ LS2ER/90-105M LSER/90-105F LS2ER/90-105S LS2ER/90-120B available models 00 mm resolution; 0... / m controlled distance area protected response tempo di controllata n n of raggi beams height (mm) risposta time (ms) (ms) (mm) series 10,5.5 LS2ER/0B-080B LS2ER/0B-080 LS2ER/0B-080M available models LS2ER/0B-080F LS2ER/0B-080S 00 mm resolution; 0... / m controlled distance area protected response tempo di controllata n n of raggi beams height (mm) risposta time (ms) (ms) (mm) series 910,5.5 LS2ER/0C-090B LS2ER/0C-090 LS2ER/0C-090M available models 0 mm resolution; 0... / m controlled distance area protected response tempo di controllata n n of raggi beams height (mm) risposta time (ms) (ms) (mm) series 160 8,5.5 LS2ER/0-015K LS2ER/0-00K LS2ER/0-05K LS2ER/ LS2ER/0-060K , , ,5 6.5 LS2ER/90-120M LS2ER/90-120F LS2ER/90-120S LS2ER/90-15B LS2ER/90-15 LS2ER/90-15M , , , , , , , LS2ER/0-075K LS2ER/0-090K LS2ER/0-105K LS2ER/0-120K LS2ER/0-15K LS2ER/0-150K LS2ER/90-15F LS2_H LS2; LS2_K; , LS2ER/90-15S LS2ER/90-150B LS2ER/

31 available models 0 mm resolution; 0... / m controlled distance area protected controllata height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series 160 8, , , , , , , , LS2ER/0-015H LS2ER/0-00H LS2ER/0-05H LS2ER/0-060H LS2ER/0-075H LS2ER/0-090H LS2ER/0-105H LS2ER/0-120H LS2ER/0-15H LS2ER/0-150H available models 0... / m controlled distance n n of raggi beams area risoluzione protected controlled response tempo di controllata height (mm) (mm) area (mm) risposta time (ms) (ms) (mm) , series LS2ER/0A-050K LS2ER/0B-080K LS2ER/0C-090K n n of raggi beams area risoluzione protected controlled response tempo di controllata height (mm) (mm) area (mm) risposta time (ms) (ms) (mm) , series LS2ER/0A-050H LS2ER/0B-080H LS2ER/0C-090H LS2; LS2_K; LS2_H 1

32 technical specifications type 2 according to EN/IEC /2 LS2ER/**-***_ tensione power di alimentazione supply Vdc Vcc power potenza consumption, assorbita, Ricevitore Receiver potenza power consumption, assorbita, Emettitore Emitter potenza power consumption, assorbita, riscaldatore heater tipo output di uscita type corrente output current di uscita carico equivalent resistivo resistive equivalente load carico capacitive capacitivo load tollerato ritardo recovery alla disponibilità time tempo di response risposta (OSSDs time OFF) angolo effective di apertura aperture effettivo angle(eaa) immunità artificial light luce rejection artificiale immunità ambient light luce rejection naturale grado di protezione IP IP protection (standard models) (modelli standard) grado di protezione IP IP protection (special models) (modelli speciali) operating temperatura temperature di lavoro operating temperatura temperature, di lavoro modelli K models K operating temperatura temperature, di lavoro modelli H models H temperatura storage di immagazzinamento temperature humidity umidità resistenza vibrations alle vibrazioni resistenza shocks agli urti lunghezza max cable length totale (power cavi aliment. supply/outputs) / uscita max cable legth for Master Slave lunghezza cavi intermedi (prolunghe) interconnections sezione dimension corpo (IP67 (modelli models) IP67) custodia tube (IP69K (modelli models) IP69K) connectors connettori modelli models LS2ER/**-***B connectors connettori modelli models LS2ER/**-*** connectors connettori modelli models LS2ER/**-***M connectors connettori modelli models LS2ER/**-***S connectors connettori modelli models LS2ER/**-***F connectors connettori modelli models LS2ER/**-***K connectors connettori modelli models LS2ER/**-***H ,2...28,8 Vdc Vcc 2 W 1 W W 2 x PNP 00 ma 60 Ω 0, µf 2 s 2, ms ± 5 according secondo to IEC IEC according secondo to IEC IEC IP65 and e IP67 IP65, IP67 and e IP69K C C C C 95% according secondo to IEC IEC according secondo to IEC IEC m 50 m (frontale) (front) x x 0 0 mm ø 56 mm Emettitore Emitter 1 x M12, 5p, maschio male Ricevitore Receiver 11 x x M12, 5p 5p maschio male Emettitore Emitter 1 x M12, 5p, maschio male Ricevitore Receiver 11 x x M12, 8p 8p maschio male Emettitore Emitter 2 x M12, 5p, maschio male Ricevitore Receiver 11 x x M12, 8p 8p maschio male x x M12, 5p 5p maschio male Emettitore Emitter 2 x M12, 5p, maschio male Ricevitore Receiver 22 x x M12, 5p 5p maschio male Emettitore Emitter 1 x M12, 5p, maschio male Ricevitore Receiver 1 1 x x M12, 5p 5p maschio male Emitter Emettitore cable cavo 5 wires 5 fili Receiver Ripetitore cable cavo 8 wires fili Emitter Emettitore cable cavo 8 wires 8 fili Receiver Ripetitore cable cavo 10 wires fili PELV power supplier according to EN Cap.6. no load H models, IP69K with heater OSSD safety outputs higher values are considered overload lower values are considered short circuit lower values may be considered short circuit IEC , 200 according to the reported standards without any additional precaution the device can t be used for outdoor applications external transparent tube resistant against 100 bar water jets no condensation no condensation, models without internal heater models with internal heater to be respected also during transportation no condensation according to the reported standards cable section 0. mm2 (to respect max length) painted aluminium RAL 1012 nichel plated brass PVC sheath, ø 5.5 mm L 10 m, 0. mm 2 LS2; LS2_K; LS2_H 2

33 safety parameters LS2ER/0-***_ altezza height (mm) number numero of raggi beams tempo response di risposta time (ms) tempo response di risposta time Master + Slave (ms) tempo response di risposta time Master + 2 Slave (ms) Type Tipo (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd (years) (anni) CFF , , , , , , , , , , , Ttot = [0,110 [0.110 * (Nr Slave1 + Nr Master) + 1,10] 1.10] * 2 (Master + 1 Slave) Ttot = [0,110 [0.110 * (Nr Slave1 + Nr Slave2 + Nr Master) + 1,228] 1.228] * 2 (Master + 2 Slave) c 2,0E E-08 2,66E E-08,0E-08.0E-08,92E-08.92E-08,57E-08.57E-08 5,19E E-08 5,8E E-08 6,5E E-08 7,09E E-08 7,71E E-08 8,5E E-08 8,98E E-08 91,0% 91.0% 91,00% 91.00% 90,90% 90.90% 90,70% 90.70% 90,60% 90.60% 90,60% 90.60% 90,50% 90.50% 90,50% 90.50% 90,0% 90.0% 90,0% 90.0% 90,0% 90.0% 90,0% 90.0% % LS2ER/0-***_ altezza height (mm) number numero of raggi beams tempo response di risposta time (ms) tempo response di risposta time Master + Slave (ms) tempo response di risposta time Master + 2 Slave (ms) Type tipo (1) (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd (years) (anni) CFF , , , , , , , , , Ttot = [0,110 [0.110 * (Nr Slave1 + Nr Master) + 1,10] 1.10] * 2 (Master + 1 Slave) Ttot = [0,110 [0.110 * (Nr Slave1 + Nr Slave2 + Nr Master) + 1,228] 1.228] * 2 (Master + 2 Slave) c 1,8E E-08 2,29E E-08 2,7E E-08,18E-08.18E-08,6E-08.6E-08,08E-08.08E-08,5E-08.5E-08,98E-08.98E-08 5,E-08 5.E-08 5,88E E-08 9,60% 9.60% 9,80% 9.80% 9,20% 9.20% 92,80% 92.80% 92,0% 92.0% 92,20% 92.20% 92,00% 92.00% 91,80% 91.80% 91,70% 91.70% 91,50% 91.50% % LS2ER/50-***_ altezza height (mm) number numero of raggi beams tempo response di risposta time (ms) (ms) tempo response di risposta time Master + Slave (ms) tempo response di risposta time Master + 2 Slave (ms) , , , , ,5.5,5.5 5, , , Ttot = [0,110 [0.110 * (Nr Slave1 + Nr Master) + 1,10] 1.10] * 2 (Master + 1 Slave) Ttot = [0,110 [0.110 * (Nr Slave1 + Nr Slave2 + Nr Master) + 1,228] 1.228] * 2 (Master + 2 Slave) Type tipo (1) (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd (years) (anni) CFF c 1,75E E-08 2,1E E-08 2,7E E-08 2,85E E-08,19E-08.19E-08,57E-08.57E-08,91E-08.91E-08,29E-08.29E-08,6E-08.6E-08 5,01E E-08 9,80% 9.80% 9,00% 9.00% 9,50% 9.50% 9,10% 9.10% 92,80% 92.80% 92,50% 92.50% 92,0% 92.0% 92,10% 92.10% 91,90% 91.90% 91,80% 91.80% % (1) ref. CEI EN :2005; CEI EN :2007 (2) ref. CEI EN 61508:2002 () ref. CEI EN 62061: CEI EN 62061/EC2:2008 () ref. UNI EN ISO 189-1:2008 LS2_H LS2; LS2_K;

34 LS2ER/90-***_ altezza height (mm) number numero of raggi beams tempo response di risposta time (ms) (ms) tempo response di risposta time Master Master + Slave + Slave (ms) (ms) tempo response di risposta time Master Master Slave 2 Slave (ms) (ms) Type tipo (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd (years) (anni) CFF Ttot = [0.110 * (Nr Slave1 + Nr Master) ] * 2 (Master + 1 Slave)) Ttot = [0.110 * (Nr Slave1 + Nr Slave2 + Nr Master) ] * 2 (Master + 2 Slave) c 1.82E E E E E E-08.18E-08.1E-08.6E % 9.20% 9.80% 9.50% 9.20% 9.00% 92.80% 92.60% 92.0% % LS2ER/**-***_ altezza height (mm) number numero of raggi beams tempo response di risposta time (ms) 0A-050 0B-080 0C tempo response di risposta time Master Master + Slave + Slave (ms) (ms) Ttot = [0.110 * (Nr Slave1 + Nr Master) ] * 2 (Master + 1 Slave) tempo response di risposta time Master Master Slave 2 Slave (ms) (ms) Type tipo (1) (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd (years) (anni) CFF Ttot = [0.110 * (Nr Slave1 + Nr Slave2 + Nr Master) ] * 2 (Master + 2 Slave) c 1.71E E E % 9.60% 9.20% % (1) ref. CEI EN :2005; CEI EN :2007 (2) ref. CEI EN 61508:2002 () ref. CEI EN 62061: CEI EN 62061/EC2:2008 () ref. UNI EN ISO 189-1:2008 LS2; LS2_K; LS2_H

35 electrical diagrams of the connections LS2 serie series LS2 receiver ricevitore unit M12 (8 (8 poli poles maschio) male) Cavo poles 8 cable poli LS2ER / **-*** LS2ER / **-***M pin colore segnale signal type tipo descrizione description 1 WH OSSD1 OUT prima first uscita safety statica di output sicurezza (PNP) (PNP) 2 BN 2V CC DC POWER tensione power di supply alimentazione input GN OSSD2 OUT seconda uscita safety statica di output sicurezza (PNP) (PNP) YE EDM IN connection to Restart restart e/o contatti di controllo (EDM) and/or external control contacts (EDM) 5 GY Mode_A IN selezione selection della of the modalità Start/Restart/EDM di Avvio/Riavvio/EDM mode 6 PK Mode_B IN selezione selection della of the modalità Start/Restart/EDM di Avvio/Riavvio/EDM mode 7 BU 0V POWER riferimento supply della voltage tensione reference di alimentazione 8 RD FE GND terra functional funzionale earth BN Power BU Power WH OSSD 1 logica possible di configurazione combinations pin (YE) pin5 (GY) pin6 (RK) funzione function BK black OG orange GN OSSD 2 2V DC 2V CC 2V DC 0V AUTO BN brown GN green YE EDM GY Mode A PK Mode B RD FE LS2ER / **-***K K1 + K2 +2V CC DC 2V CC DC 0V AUTO + EDM riavvio restart +2V CC DC 0V 2V CC DC MANUALE K1 + K2 + riavvio restart +2V CC DC 0V 2V CC DC MANUALE + EDM RD YE WH PK red yellow white pink BU GY VT blue grey violet NOTE: On these Standard and Master models it is possible to choose the operating modes by changing the wiring. By using the EDM function it is possible to extend the safety control to the contactors controlled downstream, that must be the type with guided contacts and approved for safety applications. With this model of curtain you can use the relay module SB00, but the EDM input must be connected. M12 (5 (5 poli poles maschio) male) LS2ER / **-***B pin colore segnale signal type tipo descrizione description 1 BN 2V CC DC POWER ingresso power supply alimentazione input 2 WH OSSD1 OUT prima range uscita or statica Test selection di sicurezza input (PNP) BU 0V POWER riferimento supply voltage di alimentazione reference BK OSSD2 OUT seconda range uscita or statica Test selection di sicurezza input (PNP) 5 GY FE GND terra functional funzionale earth NOTE: These Base models with automatic restart do not have the EDM function, the device downstream must therefore be able to control its own safety integrity independently. With this model of curtain you can not use the relay module SB00, because the EDM input is not available. LS2; LS2_K; LS2_H 5

36 electrical diagrams of the connections colore segnale signal type tipo descrizione description 10 Cavo poles 10 cable poli (IP69K (ricevitore with IP69K heater termostato) receiver unit) BN 2V CC DC POWER tensione power di supply alimentazione input BU 00VV POWER riferimento supply della voltage tensione reference di alimentazione BN Power BU Power WH OSSD 1 GN OSSD 2 YE EDM GY Mode A PK Mode 2 BK Heater 0 VT Heater P RD FE LS2ER / **-***H WH OSSD1 OUT prima first uscita safety statica di output sicurezza (PNP) (PNP) GN OSSD2 OUT seconda second uscita safety statica static di output sicurezza (PNP) (PNP) YE EDM IN connection restart to Restart e/o and/or contatti external di controllo control (EDM) contacts (EDM) GY Mode_A IN selezione selection della of the modalità Start/Restart/EDM di Avvio/Riavvio/EDM mode PK Mode_B IN selezione selection della of the modalità Start/Restart/EDM di Avvio/Riavvio/EDM mode BK Heater 0 POWER comune heater alimentazione supply common riscaldatore PK Heater p POWER alimentazione heater supply riscaldatore 2V DC 2V or AC CC o CA BK FE GND terra functional funzionale earth logica possible di configurazione combinations YE GY PK funzione function 2V CC 2V DC 2V CC 00VV AUTO K1 + K2 +2V CC DC 2V CC DC 00VV AUTO + EDM riavvio restart +2V DC CC 00VV 2V CC DC MANUALE K1 + K2 + riavvio restart +2V 0VV 2V CC DC MANUALE + EDM DC CC x 0 V 0V 0 V NOT NON ADMITTED AMMESSI x 2V CC 2V DC 2V CC NOT NON ADMITTED AMMESSI NOTE: On these Standard models it is possible to choose the operating modes by changing the wiring. By using the EDM function it is possible to extend the safety control to the contactors controlled downstream, that must be the type with guided contacts and approved for safety applications. The supply voltage of the thermostated heater can be indifferently 2VDC or 2VAC. With this model of curtain you can use the relay module SB00, but the EDM input must be connected. LS2 serie series LS2 emitter emettitore unit M12 (5 (5 poli poles connettore male connector) maschio) Cavo poles 5 cable poli BN Power + Range L WH Test BU Power - Range H BK Test LS2ER / **-*** LS2ER / **-***M LS2ER / **-***K pin colore segnale signal type tipo descrizione description 1 BN POWER OUT ingresso power supply alimentazione input 2 WH IN POWER ingresso range di or selezione test selection portata input o test BU POWER OUT riferimento supply voltage di alimentazione reference BK IN IN IN ingresso range di or selezione test selection portata input o test 5 GY GND IN massa functional funzionale earth logica possible di configurazione combinations pin2 (WH) pin6 (BK) funzione function LO LO LO test LO HI portata high range alta HI LO portata low range bassa HI HI HI non not ammessa admitted GY FE Levels: Livelli: LO = < 55V V o or aperto; open; HI = V to V LS2_H LS2; LS2_K; NOTE: The Test contact is necessary only if the safety chain of the receiver downstream must be periodically checked. If the Test is not necessary (the safety light curtain has already been tested independently) replace the contact with direct wiring at +2 V DC. 6

37 LS2 series LS2 emitter emettitore IP68K with IP68K heater termostato receiver unit Cavo 8 poles 8 poli cable (emettitore (IP69K with IP69K heater termostato) receiver unit) colore segnale signal type tipo descrizione description BN 2V CC DC POWER ingresso power supply alimentazione input BN Power + Range L WH Test Range H BU Power - PK N.C. YE Heater 0 RD Heater P GY FE LS2ER / **-***H WH Range L/Test IN ingresso range di or selezione test selection portata input o test BU 0V POWER riferimento supply voltage di alimentazione reference GN Range H/Test IN ingresso range di or selezione test selection portata input o test PK non not connected connesso N.C. not non connected collegato YE heater 0 POWER comune heater alimentazione supply common riscaldatore RD heater P POWER alimentazione heater supply riscaldtore 2V DC 2V or CA ACo CC GY FE GND massa functional funzionale earth logica possible di configurazione combinations WH GN funzione function LO LO LO test LO HI portata high range alta HI LO portata low range bassa HI HI HI non not ammessa admitted Levels: Livelli: LO = < <5V or o aperto; open; HI = V to NOTE: The Test contact is necessary only if the safety chain of the receiver downstream must be periodically checked. If the Test is not necessary (the safety light curtain has already been tested independently) replace the contact with direct wiring at + 2 V DC. The supply voltage of the thermostated heater can be indifferently 2 V DC or 2 V AC. The PK cable is not connected internally. LS2 serie series LS2 emitter emettitore and e receiver ricevitore unit : connettori : master slave secondari secondary Master connecotrs - Slave M12 (5 (5 poli poles maschio) male) LS2ER / **-***M LS2ER / **-***S LS2ER / **-***F pin colore segnale signal type tipo descrizione description 1 BN 2V CC DC POWER alimentazione power supply (linea(supply di alimentazione line for the per upstream il dispositivo device) a monte) 2 WH Linea 1 IN/OUT linea communication di comunicazione line 1 1 BU 0V POWER riferimento di power alimentazione supply reference (linea di alimentazione (supply per line il dispositivo for the upstream a monte) device) BK Linea 2 IN/OUT linea communication di comunicazione line GY FE GND massa functional funzionale earth NOTE: Preferably use Female/Female pre-wired extension cables (it is not permitted to access the connection lines). dimensions (mm) Dimensions dimensione of modelli Standard, Standard, Base, Base, Final models; Finale; vista view della of the base e and testa head (HEAD) with con relevant relativi connectors; connettori; see vedi Tab.:1 1 and e M12 x 1 28 L L2 0 L1 LS2; LS2_K; LS2_H 7

38 Dimensions dimensione of Master modelli and Master, Slave models; Slave; vista view of della the base e and testa head (HEAD) with con relevant relativi connectors; connettori; see vedi Tab.: 22 and e (mm) M12 x 1 L6 L5 L TAB.1 LS2 serie series LS2 dimensioni size models modelli with con rays raggi terraceda schiera modelli paired in models coppia *** dimensions dimensioni (mm) LS2ER/**-*** LS2ER/**-***B LS2ER/**-***F LS2ER/**-***M LS2ER/**-***S standard, base, finale master and e slave , , , ,56 L1 61, L2 (bottom-most L2 (prima lente) beam) 11 L L (top-most (ultima lente) beam) 26, , , , , , ,5 1, ,5 1, ,5 1, ,5 1,566.5 L 61, L5 (bottom-most L5 (prima lente) beam),5.5 L6 L6 (top-most (ultima lente) beam) TAB.2 LS2 serie series LS2 dimensione size models modelli with multiple con raggi beams multipli modelli paired in models coppia *** 0A-050 0B-080 0C-090 dimensions dimensioni (mm) LS2ER/**-*** LS2ER/**-***B LS2ER/**-***F LS2ER/**-***M LS2ER/**-***S TAB. standard, base, finale master and e slave ,05 L1 102 L2 (bottom-most L2 (prima lente) beam) 51 L L (top-most (ultima lente) beam) ,077 L 102 L5 (bottom-most L5 (prima lente) beam) 75 L6 L6 (top-most (ultima lente) beam) LS serie series LS termination tipi di terminazione types and e connectors connettori modelli models LSR (ricevitori) (receiver) LSR (emettitori) (emitter) vista base base view connettore connector vista base base view connettore connector vista base base view connettore connector vista base connettore connector LS2ER/**-*** LS2ER/**-***B LS2ER/**-***F LS2ER/**-***M LS2ER/**-***S standard base finale master slave C M12, 8p, M A - B M12, 5p, M A - B B M12, 5p, M A - B M12, 5p, M A - M12, 5p, M B (1) M12, 5p, M A - B (1) M12, 5p, M A - F M12, 8p, M D (1) M12, 5p, M E M12, 5p, M D (1) M12, 5p, M D (1) M12, 5p, M D (1) M12, 5p, M E (1) M12, 5p, M D (1) M12, 5p, M E (1) M12, 5p, M D (1) M12, 5p, M NOTE: These connectors are dedicated to a communication BUS of the Master/ Slave chain, it is not permissible to access the lines, always use cord sets. LS2; LS2_K; LS2_H 8

39 accessories ST20* / outfit mounting accessories product to used with dimensions (mm) description / installation foto LS series L Bracket Supplied as standard, pieces to couple to the length from 00 to 1,050, 6 pieces for the length from 1,200 to 1, LS series M5 Insert with threaded bolts and nuts Supplied as standard, in a number corresponding to the brackets. outfit brackets mounting LS2; LS2_K; LS2_H 9

40 dimensions (mm) modelli IP69K IP69K models L1 L2 ø L L The light Curtain is supplied already fitted inside the transparent housing. The power cord has a standard length of 10 meters and a maximum diameter of 6 mm. The brackets are included. models modelli , , , , B B B L1 dimensioni dimensions L1 (mm) , , , , , , ,160 L2 dimensioni dimensions L2 (mm) , , , , , , ,10 L dimensioni (± ) dimensions L (± ) (mm) , , , , , , ,155 L dimensioni dimensions L (mm) , , , , , , ,177 LS2; LS2_K; LS2_H 0

41 features LS, LS_K, LS_H series Light Curtains Type according to IEC and IEC Compact housing (28 x 0 mm) and no dead zone on cap side Resolution 1 mm for finger protection, 20, 0, 0 mm for hand protection, 50, 90 mm for presence control and 2,, beams for body protection/access control Controlled distance up to:,, 6, 10, 12 m Base, Standard versions and Master, Slave version to connect up to sets in cascade configuration Selectable Automatic/Manual Restart and EDM integrated functions (Standard models) Selectable controlled distance IP69K protection models (LS_K) and models with integrated heating system to reach -25 C operating temperature (LS_H) Standard M12 da 5 and 8 poles connectors download area Light Curtains Type Application notes Photos Catalogue / Manuals code description series E/R beams area 015 LS ER A 0B 0C Type safety light curtains 28 x 0 mm compact housing Emitter / Receiver couple Light grid, 1 mm resolution, finger protection Light grid, 20 mm resolution, hand protection Light grid, 0 mm resolution, hand protection Light grid, 0 mm resolution, hand protection Light grid, 50 mm resolution, presence control Light grid, 90 mm resolution, presence control 2 beams; body protection, 500 mm resolution beams; body protection, 00 mm resolution beams; body protection, 00 mm resolution Protected height from 150 to 1,800 mm (light grids) Protected height 500, 800, 900 mm (multiple light beams) Standard model with selectable MANUAL/AUTOMATIC Restart and EDM functions LS ER / B Base model with integrated AUTOMATIC Restart model M S Master Model with selectable functions Intermediate Slave model F Final Slave model distance L Controlled distance Extended range IP65 and IP67 protection, C operating temperature models K H Models in transparent cylindrical housing, IP69K, suitable for applications in the food industry. Resistance to washing with water at 100 bar, 80 C Housing in PMMA, caps in POM C with silicone seals. Brackets in stainless steel AISI 16L. Operating temperature C Models in transparent cylindrical casing, IP69K protection, thermostated, suitable for applications in the food industry. Resistance to washing with water at 100 bar, 80 C Housing in PMMA, POM C caps and silicone seals. Brackets in stainless steel AISI 16L. Operating temperature C LS_H LS; LS_K; 1

42 available models 1 mm resolution; 0... / m controlled distance available models 20 mm resolution; /...20 m controlled distance area protected controllata height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series area controllata protected height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series LSER/1-015B LSER/1-015 LSER/1-015F LSER/1-00B LSER/1-00 LSER/1-00M LSER/1-00F LSER/1-00S LSER/1-05B , , LSER/20-015BL LSER/20-015BL LSER/20-00BL LSER/20-00L LSER/20-05BL LSER/20-05L LSER/20-060BL LSER/20-060L 5 7,5 7.5 LSER/1-05 LSER/1-05M LSER/1-05F LSER/1-05S LSER/1-060B LSER/20-075BL LSER/20-075L LSER/20-090BL LSER/20-090L LSER/1-060 LSER/1-060M LSER/1-060F LSER/1-060S LSER/1-075B 1, , , , LSER/20-105BL LSER/20-105L LSER/120BL LSER/120L LSER/1-075 LSER/1-075M LSER/1-075F LSER/1-075S LSER/1-090B 1, 1. 1, LSER/15BL LSER/15L LSER/150BL LSER/150L LSER/ LSER/1-090M LSER/1-090F LSER/1-090S available models 0 mm resolution; 0... / m controlled distance 1.0 1, ,5 1.5 LSER/1-105B LSER/1-105 LSER/1-105M LSER/1-105F LSER/1-105S protected altezza height (mm) ottica (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series LSER/0-015B LSER/0-015 LSER/1-120B LSER/0-015F , , LSER/1-120 LSER/1-120M LSER/1-120F LSER/1-120S LSER/1-15B LSER/ ,5 LSER/0-00B LSER/0-00 LSER/0-00M LSER/0-00F LSER/0-00S 1. 1, LSER/1-15M LSER/0-05B LSER/1-15F LSER/0-05 LSER/1-15S ,5 LSER/0-05M LSER/1-150B LSER/0-05F LS_H LS; LS_K; 1.9 1, LSER/1-150 LSER/1-150M LSER/1-150F LSER/1-150S LSER/0-05S LSER/0-060B LSER/0-060 LSER/0-060M LSER/0-060F LSER/0-060S 2

43 available models 0 mm resolution; 0... / m controlled distance available models 0 mm resolution; / m controlled distance protected altezza height (mm) ottica (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series protected altezza height (mm) ottica (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series LSER/0-015B LSER/ LSER/0-015BL LSER/0-015L ,5 LSER/0-015F LSER/0-00B LSER/0-00 LSER/0-00M LSER/0-00F LSER/0-00BL LSER/0-00L LSER/0-05BL LSER/0-05L ,5 LSER/0-00S LSER/0-05B LSER/0-05 LSER/0-05M LSER/0-05F ,5 LSER/0-060BL LSER/0-060L LSER/0-075BL LSER/0-075L LSER/0-05S LSER/0-060B ,5 LSER/0-090BL LSER/0-090L LSER/0-060 LSER/0-060M LSER/0-060F LSER/0-060S LSER/0-075B , , , ,5 9.5 LSER/0-105BL LSER/0-105L LSER/0-120BL LSER/0-120L ,5 LSER/0-075 LSER/0-075M LSER/0-075F LSER/0-075S LSER/0-090B , , LSER/0-15BL LSER/0-15L LSER/0-150BL LSER/0-150L LSER/ , LSER/0-165L ,5 LSER/0-090M LSER/0-090F , LSER/0-180L LSER/0-090S LSER/0-105B available models , , , , LSER/0-105 LSER/0-105M LSER/0-105F LSER/0-105S LSER/0-120B LSER/0-120 LSER/0-120M LSER/0-120F LSER/0-120S LSER/0-15B LSER/0-15 LSER/0-15M LSER/0-15F 0 mm; 0... / m controlled distance protected altezza height (mm) ottica (mm) n n of raggi beams response tempo di risposta time (ms) (ms).5,5.5,5 series LSER/0-015B LSER/0-015 LSER/0-015M LSER/0-015F LSER/0-015S LSER/0-00B LSER/0-00 LSER/0-00M LSER/0-15S LSER/0-00F LSER/0-150B LSER/0-00S LSER/0-150 LSER/0-05B , , , , LSER/0-150M LSER/0-150F LSER/0-150S LSER/0-165 LSER/ ,5 LSER/0-05 LSER/0-05M LSER/0-05F LSER/0-05S LS_H LS; LS_K;

44 available models 0 mm resolution; 0... / m controlled distance available models 0 mm resolution; /...20 m controlled distance altezza protected ottica height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series altezza protected ottica height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series LSER/0-060B LSER/ LSER/0-015BL LSER/0-015L LSER/0-060M LSER/0-060F ,5 LSER/0-00BL LSER/0-00L LSER/0-060S LSER/0-075B LSER/0-05BL LSER/0-05L LSER/0-075 LSER/0-075M ,5.5 LSER/0-060BL LSER/0-060L LSER/0-075F LSER/0-075S LSER/0-075BL LSER/0-075L LSER/0-090B LSER/0-090 LSER/0-090M LSER/0-090F , ,5 6.5 LSER/0-090BL LSER/0-090L LSER/0-105BL LSER/0-105L LSER/0-090S LSER/0-105B , LSER/0-120BL LSER/0-120L , LSER/0-105 LSER/0-105M ,60 6 7,5 7.5 LSER/0-15BL LSER/0-15L LSER/0-105F LSER/0-105S , LSER/0-150BL LSER/0-150L LSER/0-120B , LSER/0-120 LSER/0-120M LSER/0-120F available models 50 mm resolution; 0... / m controlled distance LSER/0-120S LSER/0-15B altezza protected ottica height (mm) (mm) n raggi n of beams tempo di risposta response (ms) time (ms) serie series , , , ,5 LSER/0-15 LSER/0-15M LSER/0-15F LSER/0-15S LSER/0-150B LSER/0-150 LSER/0-150M LSER/0-150F LSER/0-150S LSER/50-015B LSER/0-060B LSER/50-015B LSER/0-060B LSER/ LSER/ LSER/50-015M LSER/50-015M LSER/50-015F LSER/50-015F LSER/50-015S LSER/50-015S LSER/50-00B LSER/50-00B LSER/50-00 LSER/50-00 LSER/50-00M LSER/50-00M LSER/50-00F LSER/50-00F LSER/50-00S LSER/50-00S LS; LS_K; LS_H

45 available models 50 mm resolution; 0... / m controlled distance available models 50 mm resolution; /...20 m controlled distance protected altezza height (mm) ottica (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series altezza protected ottica height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series ,5 LSER/50-05B LSER/0-060B LSER/50-05 LSER/50-05M LSER/50-05F LSER/50-05S LSER/50-060B ,5.5,5 LSER/50-015BL LSER/50-015L LSER/50-00BL LSER/50-00L LSER/50-05BL LSER/50-05L ,5 LSER/ LSER/50-060M LSER/50-060BL LSER/50-060L LSER/50-060F LSER/50-060S ,5.5 LSER/50-075BL LSER/50-075L , ,5 LSER/50-075B LSER/ LSER/50-075M LSER/50-075F LSER/50-075S LSER/50-090B LSER/ LSER/50-090M LSER/50-090F LSER/50-090S , , , , , ,5 7 LSER/50-090BL LSER/50-090L LSER/50-105BL LSER/50-105L LSER/50-120BL LSER/50-120L LSER/50-15BL LSER/50-15L LSER/50-150BL LSER/50-150L LSER/50-105B LSER/ available models 1, ,5 LSER/50-105M 90 mm resolution; 0... / m controlled distance LSER/50-105F LSER/50-105S protected altezza height (mm) ottica (mm) n n of raggi beams tempo response di risposta time (ms) series LSER/50-120B LSER/90-00B LSER/0-060B LSER/ LSER/ , ,5 LSER/50-120M 10 LSER/90-00M LSER/50-120F LSER/90-00F LSER/50-120S LSER/90-00S LSER/50-15B LSER/50-15B LSER/90-05B LSER/50-15 LSER/50-15 LSER/ , LSER/50-15M LSER/50-15M 60 6,5.5 LSER/90-05M LSER/50-15F LSER/50-15F LSER/90-05F LSER/50-15S LSER/50-15S LSER/90-05S LSER/50-150B LSER/50-150B LSER/90-060B LSER/ LSER/ LSER/ , LSER/50-150M LSER/50-150M LSER/50-150F LSER/50-150F LSER/50-150S LSER/90-060M LSER/90-060F LSER/90-060S LS_H LS; LS_K; 5

46 available models 90 mm resolution; 0... / m controlled distance available models 90 mm resolution; /...20 m controlled distance protected altezza height (mm) ottica (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series altezza protected ottica height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series LSER/90-075B LSER/0-060B LSER/ ,5 LSER/90-00BL LSER/90-00L ,5.5 LSER/90-075M LSER/90-075F 60 6 LSER/90-05BL LSER/90-05L LSER/90-075S LSER/90-090B LSER/90-060BL LSER/90-060L LSER/ LSER/90-090M ,5.5 LSER/90-075BL LSER/90-075L LSER/90-090F LSER/90-090S ,5.5 LSER/90-090BL LSER/90-090L , , , ,5 5.5 LSER/90-105B LSER/ LSER/90-105M LSER/90-105F LSER/90-105S LSER/90-120B LSER/ LSER/90-120M , , , , ,5.5,5 LSER/90-105BL LSER/90-105L LSER/90-120BL LSER/90-120L LSER/90-15BL LSER/90-15L LSER/90-150BL LSER/90-150L. LSER/90-120F LSER/90-120S LSER/90-15B available models resolution 2,, beams; 0... / m controlled distance , LSER/90-15 LSER/90-15M altezza protected ottica height (mm) (mm) n n of beams raggi distance distanza betw. tra i beams raggi (mm) response tempo di risposta time (ms) (ms) series LSER/90-15F LSER/0A-050B , ,5 LSER/90-15S LSER/90-150B LSER/ LSER/90-150M ,5 LSER/0A-050 LSER/0A-050M LSER/0A-050F LSER/0A-050S LSER/0B-080B LSER/90-150F LSER/90-150S LSER/0B-080 LSER/0B-080M LSER/0B-080F LSER/0B-080S LSER/0C-090B LSER/0C LSER/0C-090M LSER/0C-090F LSER/0C-090S LS; LS_K; LS_H 6

47 available models resolution 2,, beams; /...20 m controlled distance available models 1 mm resolution; 0... / m controlled distance altezza protected ottica n n of height (mm) (mm) beams raggi distance distanza betw. tra i beams raggi (mm) response tempo di risposta time (ms) (ms) series area protected controllata height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series ,5 LSER/0A-050BL LSER/0A-050L ,5 5.5 LSER/1-015H LSER/1-00H ,5 LSER/0B-080BL LSER/0B-080L 5 7, LSER/1-05H LSER/1-060H ,5 LSER/0C-090BL LSER/0C-090L LSER/1-075H LSER/1-090H available models 1 mm resolution; 0... / m controlled distance area protected response tempo di controllata n n of raggi beams height (mm) risposta time (ms) (ms) (mm) , , , , , , , , available models series LSER/1-015K LSER/1-00K LSER/1-05K LSER/1-060K LSER/1-075K LSER/1-090K LSER/1-105K LSER/1-120K LSER/1-15K LSER/1-150K 0 mm resolution; /...17 m controlled distance area protected response tempo di controllata n n of raggi beams height (mm) risposta time (ms) (ms) (mm) series LSER/0-015LK LSER/0-00LK 1.0 1, ,5 1.5 LSER/1-105H , , LSER/1-120H 1. 1, LSER/1-15H 1.9 1, LSER/1-150H available models 0 mm resolution; /...17 m controlled distance area protected response tempo di controllata n n of raggi beams height (mm) risposta time (ms) (ms) (mm) serie LSER/0-015LH LSER/0-00LH LSER/0-05LH LSER/0-060LH ,5 6.5 LSER/0-075LH ,5 7.5 LSER/0-090LH , ,5 8.5 LSER/0-105LH , ,5 9.5 LSER/0-120LH , LSER/0-15LH , LSER/0-150LH available models resolution 2,, beams; /...20 m controlled distance , , , , , ,5 9.5 LSER/0-05LK LSER/0-060LK LSER/0-075LK LSER/0-090LK LSER/0-105LK LSER/0-120LK area protected controllata height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) 2,5 2.5 series LSER/0A-050LK LSER/0B-080LK LSER/0C-090LK , , LSER/0-15LK LSER/0-150LK available models resolution 2,, beams; /...20 m controlled distance area protected controllata height (mm) (mm) n n of raggi beams response tempo di risposta time (ms) (ms) series LSER/0A-050LH ,5 2.5 LSER/0B-080LH LSER/0C-090LH LS_H LS; LS_K; 7

48 technical specifications type according to EN/IEC /2 LSER/**-***_ tensione power di alimentazione supply Vdc Vcc power potenza consumption, assorbita, Ricevitore Receiver potenza power consumption, assorbita, Emettitore Emitter potenza power consumption, assorbita, riscaldatore heater tipo output di uscita type output corrente current carico equivalent resistivo resistive equivalente load carico capacitive capacitivo load tollerato ritardo recovery alla disponibilità time tempo di response risposta (OSSDs time OFF) angolo effective di apertura aperture effettivo angle(eaa) immunità artificial light luce rejection artificiale immunità ambient light luce rejection naturale grado IP di protection protezione IP (standard (modelli standard) models) grado IP di protection protezione IP (modelli (special speciali) models) operating temperatura temperature di lavoro operating temperatura temperature, di lavoro modelli K models K operating temperatura temperature, di lavoro modelli H models H temperatura storage di immagazzinamento temperature humidity umidità resistenza vibrations alle vibrazioni resistenza shocks agli urti lunghezza max cable length totale (power cavi aliment. supply/outputs) / uscita lunghezza max cable cavi legth intermedi for Master (prolunghe) Slave interconnections sezione dimension corpo (IP67 (modelli models) IP67) custodia tube (IP69K (modelli models) IP69K) connectors connettori modelli models LSER/**-***B LS2ER/**-***B connectors connettori modelli models LSER/**-*** LS2ER/**-*** connectors connettori modelli models LSER/**-***M LS2ER/**-***M connectors connettori modelli models LSER/**-***S LS2ER/**-***S connectors connettori modelli models LSER/**-***F LS2ER/**-***F connectors connettori modelli models LSER/**-***K LS2ER/**-***K connectors connettori modelli models LSER/**-***H LS2ER/**-***H 19,2...28, W 1 W W 2 x PNP 00 ma 60 Ω 0, µf 2 s 2, ms ± 2,5 2.5 according secondo to IEC IEC according secondo to IEC IEC IP65 e IP67 IP65, IP67 and e IP69K C C C C 95% according secondo to IEC IEC according secondo to IEC IEC m 50 m (frontale) (front) x x 0 0 mm ø 56 mm emettitore Emitter 1 x M12, 5p, maschio male ricevitore Receiver 1 1 x x M12, 5p 5p maschio male emettitore Emitter 1 x M12, 5p, maschio male ricevitore Receiver 1 1 x x M12, 8p 8p maschio male emettitore Emitter 2 x M12, 5p, maschio male ricevitore Receiver 1 1 x x M12, 8p 8p maschio male x x M12, 5p 5p maschio male emettitore Emitter 2 x M12, 5p, maschio male ricevitore Receiver 2 2 x x M12, 5p 5p maschio male emettitore Emitter 1 x M12, 5p, maschio male ricevitore Receiver 1 1 x x M12, 5p 5p maschio male emettitore Emitter 5 cavo wires 5 fili ripetitore Receiver cavo 8 wires 8 fili emettitore Emitter 8 cavo wires 8 fili ripetitore Receiver10 cavo wires 10 fili PELV power supplier according to EN Cap.6. no load H models, IP69K with heater OSSD safety outputs higher values are considered overload lower values are considered short circuit lower values may be considered short circuit IEC , 200 according to the reported standards without any additional precaution the device can t be used for outdoor applications external transparent tube resistant against 100 bar water jets no condensation no condensation, models without internal heater models with internal heater to be respected also during transportation no condensation according to the reported standards cable section 0. mm2 (to respect max length) painted aluminium RAL 1012 nichel plated brass PVC sheath, ø 5.5 mm L 10 m, 0. mm 2 LS; LS_K; LS_H 8

49 safety parameters LSER/1-***_ altezza height (mm) number numero of raggi beams tempo response di risposta time (ms) tempo response di risposta time Master + Slave (ms) tempo response di risposta time Master + 2 Slave (ms) Type Tipo (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd MTTFd (anni) CFF , , ,60 1, , , , , Ttot = [0.06 [0,06 * (Nr Slave1 + Nr Master) ] 0,966] * 2 (Master + 1 Slave) Ttot = [0.06 [0,06 * (Nr Slave1 + Nr Slave2 + Nr Master) ] 1,006] * 2 (Master + 2 Slave) e 1,0E E-08 1,27E E-08 1,52E E-08 1,75E E-08 2,00E E E-08 2,2E E-08 2,9E E-08 2,7E E-08 2,98E-08.22E-08,22E-08 95,0% 95.0% 9,90% 9.90% 9,50% 9.50% 9,10% 9.10% 9,80% 9.80% 9,60% 9.60% 9,0% 9.0% 9,10% 9.10% 92,90% 92.90% 92.80% 92,80% % LSER/0-***_ altezza height (mm) number numero of raggi beams tempo response di risposta time (ms) (ms) tempo response di risposta time Master + Slave (ms) tempo response di risposta time Master + 2 Slave (ms) Type Tipo (1) (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd MTTFd (anni) CFF , , , , , , , , , , , , Ttot = [0,11 [0.11 * (Nr Slave1 + Nr Master) + 0,976] 0.976] * 2 (Master + 1 Slave) Ttot = [0,11 [0.11 * (Nr Slave1 + Nr Slave2 + Nr Master) + 1,0508] ] * 2 (Master + 2 Slave) e 7,08E E-09 8,20E E-09 9,5E E-09 1,06E E-08 1,19E E E-08 1,0E-08 1.E-08 1,E E-08 1,5E E-08 1,67E E-08 1,78E E-08 1,90E E-08 2,02E % 96,60% 97,00% 97.00% 97,20% 97.20% 97,0% 97.0% 97,0% 97.0% 97,50% 97.50% 97,70% 97.70% 97,60% 97.60% 97,70% 97.70% 97,70% 97.70% 97,70% 97.70% 97,80% 97.80% % LSER/0-***_ altezza height (mm) number numero of raggi beams tempo response di risposta time (ms) (ms) tempo response di risposta time Master + Slave (ms) tempo response di risposta time Master + 2 Slave (ms) , , , , ,5.5,5.5 5, , ,5 1.5 Ttot = [0,11 [0.11 * (Nr Slave1 + Nr Master) + 0,976] 0.976] * 2 (Master + 1 Slave) Ttot = [0,11 [0.11 * (Nr Slave1 + Nr Slave2 + Nr Master) + 1,0508] ] * 2 (Master + 2 Slave) Type Tipo (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd MTTFd (anni) CFF e 6,82E E-09 7,76E E-09 8,58E E-09 9,52E E-09 1,0E E-08 1,1E E-08 1,21E E-08 1,0E E-08 1,8E E-08 1,8E E-08 96,0% 96.0% 96,70% 96.70% 96,90% 96.90% 97,10% 97.10% 97,20% 97.20% 97,0% 97.0% 97,0% 97.0% 97,0% 97.0% 97,50% 97.50% 97,50% 97.50% % (1) ref. CEI EN :2005; CEI EN :2007 (2) ref. CEI EN 61508:2002 () ref. CEI EN 62061: CEI EN 62061/EC2:2008 () ref. UNI EN ISO 189-1:2008 LS_H LS; LS_K; 9

50 LSER/50-***_ height (mm) number of beams response time (ms) response time Master + Slave (ms) response time Master + 2 Slave (ms) Type (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd CFF ,060 1,210 1,60 1, Ttot = [0.11 * (Nr Slave1 + Nr Master) ] * 2 (Master + 1 Slave) Ttot = [0.11 * (Nr Slave1 + Nr Slave2 + Nr Master) ] * 2 (Master + 2 Slave) e 6.5E E E E E E E E E E % 96.80% 96.90% 97.10% 97.20% 97.0% 97.0% 97.50% 97.50% 97.50% % LSER/90-***_ height (mm) number of beams response time (ms) response time Master + Slave (ms) response time Master + 2 Slave (ms) Type (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd CFF ,060 1,210 1,60 1, Ttot = [0.11 * (Nr Slave1 + Nr Master) ] * 2 (Master + 1 Slave) Ttot = [0.11 * (Nr Slave1 + Nr Slave2 + Nr Master) ] * 2 (Master + 2 Slave) e 6.79E E E-09 8,8E-09 9,17E-08 9,80E-08 1,05E-08 1,11E-08 1,18E % 96.60% 96.70% 96.80% 96.90% 96.90% 97.00% 97.10% 97.10% % LSER/**-***_ height (mm) number of beams response time (ms) response time Master + Slave (ms) response time Master + 2 Slave (ms) 0A-050 0B-080 0C ,5 Ttot = [0.11 * (Nr Slave1 + Nr Master) ] * 2 (Master + 1 Slave) Ttot = [0.11 * (Nr Slave1 + Nr Slave2 + Nr Master) ] * 2 (Master + 2 Slave) LS_H LS; LS_K; Type (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd CFF e 6.89E E E % 96.20% 96.10% % (1) ref. CEI EN :2005; CEI EN :2007 (2) ref. CEI EN 61508:2002 () ref. CEI EN 62061: CEI EN 62061/EC2:2008 () ref. UNI EN ISO 189-1:

51 LSER/20-***_L height (mm) number of beams response time (ms) response time Master + Slave (ms) response time Master + 2 Slave (ms) Type (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd CFF ,060 1,210 1,60 1, Ttot = [0.06 * (Nr Slave1 + Nr Master) ] * 2 (Master + 1 Slave) Ttot = [0.06 * (Nr Slave1 + Nr Slave2 + Nr Master) ] * 2 (Master + 2 Slave) e 1.0E E E E E E E E E-08.22E % 9.90% 9.50% 9.10% 9.80% 9.60% 9.0% 9.10% 92.90% 92.80% % LSER/0-***_ height (mm) number of beams response time (ms) response time Master + Slave (ms) response time Master + 2 Slave (ms) Type (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd CFF ,060 1,210 1,60 1,510 1,660 1, Ttot = [0.06 * (Nr Slave1 + Nr Master) ] * 2 (Master + 1 Slave) Ttot = [0.06 * (Nr Slave1 + Nr Slave2 + Nr Master) ] * 2 (Master + 2 Slave) e 9.1E E E E E E E E E E E E % 95.0% 95.10% 9.90% 9.70% 9.50% 9.0% 9.10% 9.90% 9.80% 9.70% 9.60% % LSER/0-***_L height number of beams response time (ms) response time Master + Slave (ms) response time Master + 2 Slave (ms) ,060 1,210 1,60 1, , Ttot = [0.06 * (Nr Slave1 + Nr Master) ] * 2 (Master + 1 Slave)) Ttot = [0.06 * (Nr Slave1 + Nr Slave2 + Nr Master) ] * 2 (Master + 2 Slave) Type (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd CFF e 8.8E E E E E-08 1.E E E E E % 95.50% 95.0% 95.10% 95.00% 9.80% 9.70% 9.50% 9.0% 9.20% % (1) ref. CEI EN :2005; CEI EN :2007 (2) ref. CEI EN 61508:2002 () ref. CEI EN 62061: CEI EN 62061/EC2:2008 () ref. UNI EN ISO 189-1:2008 LS_H LS; LS_K; 51

52 LSER/50-***_L height (mm) number of beams response time (ms) response time Master + Slave (ms) response time Master + 2 Slave (ms) Type (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd CFF ,060 1,210 1,60 1, Ttot = [0.06 * (Nr Slave1 + Nr Master) ] * 2 (Master + 1 Slave)) Ttot = [0.06 * (Nr Slave1 + Nr Slave2 + Nr Master) ] * 2 (Master + 2 Slave) e 8.50E E E-09 1.E E E E E E-08 1.E % 95.70% 95.50% 95.0% 95.20% 95.10% 9.90% 9.80% 9.70% 9.60% % LSER/90-***_L height (mm) number of beams response time (ms) response time Master + Slave (ms) response time Master + 2 Slave (ms) Type (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd CFF ,060 1,210 1,60 1, Ttot = [0.06 * (Nr Slave1 + Nr Master) ] * 2 (Master + 1 Slave)) Ttot = [0.06 * (Nr Slave1 + Nr Slave2 + Nr Master) ] * 2 (Master + 2 Slave) e 8.71E E E E E E E E E % 95.70% 95.60% 95.0% 95.0% 95.10% 95.00% 9.80% 95.00% % LSER/**-***_L 0A-050 0B-080 0C-090 height (mm) number of beams response time (ms) response time Master + Slave (ms) response time Master + 2 Slave (ms) Ttot = [0.06 * (Nr Slave1 + Nr Master) ] * 2 (Master + 1 Slave) Ttot = [0.06 * (Nr Slave1 + Nr Slave2 + Nr Master) ] * 2 (Master + 2 Slave) LS_H LS; LS_K; Type (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd CFF e 9.15E E E % 95.60% 95.0% % (1) ref. CEI EN :2005; CEI EN :2007 (2) ref. CEI EN 61508:2002 () ref. CEI EN 62061: CEI EN 62061/EC2:2008 () ref. UNI EN ISO 189-1:

53 electrical diagrams of the connections serie LS Ricevitore M12 (8 (8 poli poles maschio) male) Cavo poles 8 male poli LSER / **-*** LSER / **-***M pin colore segnale signal type tipo descrizione description 1 WH OSSD1 OUT prima first uscita safety statica di output sicurezza (PNP) (PNP) 2 BN 2V CC DC POWER tensione power di supply alimentazione input GN OSSD2 OUT seconda uscita safety statica di output sicurezza (PNP) (PNP) YE EDM IN connection to Restart and/or restart e/o contatti di controllo (EDM) external control contacts (EDM) 5 GY Mode_A IN selezione selection della of modalità the Start/Restart/EDM di Avvio / Riavvio mode / EDM 6 PK Mode_B IN selezione selection della of modalità the Start/Restart/EDM di Avvio / Riavvio mode / EDM 7 BU 0V POWER riferimento supply della voltage tensione reference di alimentazione 8 RD FE GND terra functional funzionale earth BN Power BU Power WH OSSD 1 GN OSSD 2 YE EDM GY Mode A PK Mode 2 LSER / **-***K logica possible di configurazione combinations pin (YE) pin5 (GY) pin6 (RK) funzione function 2V DC 2V CC 2V DC 0V AUTO K1 + K2 +2V CC DC 2V CC DC 0V AUTO + EDM riavvio restart +2V CC DC 0V 2V CC DC MANUALE BK BN RD YE WH black brown red yellow white OG GN BU GY VT orange green blue grey violet RD FE K1 + K2 + riavvio restart +2V CC DC 0V 2V CC DC MANUALE + EDM PK pink NOTE: On these Standard and Master models it is possible to choose the operating modes by changing the wiring. By using the EDM function it is possible to extend the safety control to the contactors controlled downstream, that must be the type with guided contacts and approved for safety applications. With this model of curtain you can use the relay module SB00, but the EDM input must be connected. M12 (5 (5 poli poles maschio) male) LSER / **-***B pin colore segnale signal type tipo descrizione description 1 BN 2V CC DC POWER ingresso power supply alimentazione input 2 WH OSSD1 OUT prima first uscita safety statica di output sicurezza (PNP) (PNP) BU 0V POWER riferimento supply voltage di alimentazione reference BK OSSD2 OUT seconda uscita safety statica di output sicurezza (PNP) (PNP) 5 GY FE GND functional terra funzionale earth NOTE: These Base models with automatic restart do not have the EDM function, the device downstream must therefore be able to control its own safety integrity independently. With this model of curtain you can not use the relay module SB00, because the EDM input is not available. LS; LS_K; LS_H 5

54 colore segnale signal type tipo descrizione description Cavo 10 poles 10 poli cable (emettitore (IP69K with IP69K heater termostato) receiver unit) BN Power BU Power WH OSSD 1 GN OSSD 2 YE EDM GY Mode A PK Mode 2 BK Heater 0 VT Heater P RD FE LSER / **-***H BN 2VV DC CC POWER tensione power di supply alimentazione input BU 0v POWER riferimento supply della voltage tensione reference di alimentazione WH OSSD1 OUT prima first uscita safety statica di output sicurezza (PNP) (PNP) GN OSSD2 OUT seconda uscita safety statica di output sicurezza (PNP) (PNP) YE EDM IN connection to restart e/o and/or contatti external di controllo (EDM) contacts (EDM) GY Mode_A IN selezione selection della of the modalità Start/Restart/EDM di Avvio/Riavvio/EDM mode PK Mode_B IN selezione selection della of the modalità Start/Restart/EDM di Avvio/Riavvio/EDM mode BK Heater 0 POWER comune heater alimentazione supply common riscaldatre PK Heater p POWER alimentazione heater supply riscaldatore 2V DC 2V or AC CC o CA BK FE GND functional terra funzionale earth logica possible di configurazione combinations YE GY PK funzione function 2V DC 2 V CC 2V DC 0VV AUTO BK black OG orange K1 + K2 +2V CC DC 2VV DC CC 0VV AUTO + EDM riavvio restart +2V CC DC 0VV 2VV DC CC MANUALE K1 + K2 + riavvio restart +2V CC DC 0VV 2VV DC CC MANUALE + EDM BN RD YE WH PK brown red yellow white pink GN BU GY VT green blue grey violet x 0V 0 V 0V NOT NON ADMITTED AMMESSI x 2V DC 2 V CC 2V DC NOT NON ADMITTED AMMESSI NOTE: On these Standard models it is possible to choose the operating modes by changing the wiring. By using the EDM function it is possible to extend the safety control to the contactors controlled downstream, that must be the type with guided contacts and approved for safety applications. The supply voltage of the thermostated heater can be indifferently 2 V DC or 2 V AC. With this model of curtain you can use the relay module SB00, but the EDM input must be connected. LS2 serie series LS Emettitore emitter unit M12 (5 (5 poli poles connettore male connector) maschio) LSER / **-*** LSER / **-***M pin colore segnale signal type tipo descrizione description 1 BN POWER OUT ingresso power supply alimentazione input 2 WH IN POWER ingresso range di or selezione test selection portata input o test BU POWER OUT riferimento supply voltage di alimentazione reference BK IN IN IN ingresso range di or selezione test selection portata input o test 5 GY IN IN IN massa functional funzionale earth 5 Cavo poles 5 cable poli logica possible di configurazione combinations pin2 (WH) pin6 (BK) funzione function BN Power + Range L WH Test BU Power - Range H BK Test LSER / **-***K LO LO LO test LO HI portata high range alta HI LO portata low range bassa HI HI HI NOT non ADMITTED ammessa BK BN black brown RD red YE yellow WH white PK pink OG orange GN green BU blue GY grey VT violet GY FE Levels: Livelli: LO = < 5V o or aperto; open; HI = V to 0V LS_H LS; LS_K; NOTE: The Test contact is necessary only if the safety chain of the receiver downstream must be periodically checked. If the Test is not necessary (the safety light curtain has already been tested independently) replace the contact with direct wiring at +2 V DC. 5

55 LS serie series LS Emettitore IP69K with IP68K heater termostato Emitter unit Cavo 8 poles 8 poli cable (emettitore (IP69K with IP69K heater termostato) emitter unit) colore segnale signal type tipo descrizione description BN 2 CC POWER ingresso power supply alimentazione input BN Power + Range L WH Test Range H BU Power - PK N.C. YE Heater 0 RD Heater P GY FE LSER / **-***H WH Range L/Test IN ingresso range di or selezione test selection portata input o test BU 0V POWER riferimento supply voltage di alimentazione reference GN Range H/Test IN ingresso range di or selezione test selection portata input o test PK non not connected connesso N.C. not non connected collegato YE heater 0 POWER comune heater alimentazione supply common riscaldatore RD heater P POWER alimentazione heater supply riscaldtore 2V DC 2V or CA ACo CC GY FE GND massa functional funzionale earth logica possible di configurazione combinations WH GN funzione function LO LO LO test BK BN black brown OG GN orange green LO HI portata high range alta RD red BU blue HI LO portata low range bassa YE WH yellow white GY VT grey violet HI HI HI non not ammessa admitted PK pink levels: Livelli: LO = <5V or aperto; open; HI = 11 0V to 0V NOTE The Test contact is necessary only if the safety chain of the receiver downstream must be periodically checked. If the Test is not necessary (the safety light curtain has already been tested independently) replace the contact with direct wiring at +2VDC. The supply voltage of the thermostated heater can be indifferently 2 V DC or 2 V AC. The PK cable is not connected internally LS serie series LS emitter Emettitore and e receiver Ricevitore unit : connettori : master slave secondari secondary Master connectors - Slave M12 (5 (5 poli poles maschio) male) LSER / **-***M LSER / **-***S LSER / **-***F pin colore segnale signal type tipo descrizione description 1 BN 2V CC POWER alimentazione power supply (supply line for the upstream device) (linea di alimentazione per il dispositivo a monte) 2 WH Linea 1 IN/OUT linea communication di comunicazione line 1 1 BU 0V POWER riferimento di power alimentazione supply reference (linea di alimentazione (supply per line il dispositivo for the upstream a monte) device) BK Linea 2 IN/OUT linea communication di comunicazione line 22 5 GY FE GND massa functional funzionale earth NOTE: Preferably use Female/Female pre-wired extension cables (it is not permitted to access the connection lines). dimensions (mm) dimensions dimensione of modelli Standard, Standard, Base, Final Base, models; Finale; vista view of della the base e and testa head (HEAD) with con relevant relativi connectors; connettori; see vedi Tab.: 11 and e M12 x 1 28 L L2 0 L1 LS; LS_K; LS_H 55

56 dimensione Dimensions modelli of Master Standard, Slave Base, models; Finale; view vista of della the base and e testa head (HEAD) with relevant con relativi connectors; connettori; see vedi Tab.: Tab. 2 and 2 e M12 x 1 L L2 L1 TAB.1 LS2 serie series LS dimensioni modelli con raggi a schiera modelli paired in models coppia *** dimensions dimensioni (mm) LSER/**-*** LSER/**-***B LSER/**-***F LSER/**-***M LSER/**-***S standard, base, finale master and e slave , , , ,56 L1 61,5 L2 (bottom-most L2 (prima lente) beam) 11 L L (top-most (ultima lente) beam) 26, , , , , , ,5 1, ,5 1, ,5 1, ,5 1,566.5 L 61, L5 (bottom-most L5 (prima lente) beam),5.5 L6 L6 (top-most (ultima lente) beam) TAB.2 LS serie series LS dimensione modelli con raggi multipli modelli paired in models coppia *** 0A-050 0B-080 0C-090 dimensions dimensioni (mm) LSER/**-*** LSER/**-***B LSER/**-***F LSER/**-***M LSER/**-***S TAB. standard, base, finale master and e slave ,05 L1 102 L2 (bottom-most L2 (prima lente) beam) 51 L L (top-most (ultima lente) beam) ,077 L L L5 (prima lente) L5 (bottom-most beam) 75 L6 L6 (top-most (ultima lente) beam) LS serie series LS tipi di terminazione e connettori modelli models LSR LS2R (ricevitori) (receiver) LSR LS2R (emettitori) (emitter) vista base base view connettore connector vista base base view connettore connector vista base base view connettore connector vista base base view connettore connector LSER/**-*** LSER/**-***B LSER/**-***F LSER/**-***M LSER/**-***S standard base finale master slave C M12, 8p, M A - B M12, 5p, M A - B M12, 5p, M A - B M12, 5p, M A - B (1) M12, 5p, M A - B (1) M12, 5p, M A - F M12, 8p, M D (1) M12, 5p, M E M12, 5p, M D (1) M12, 5p, M E (1) M12, 5p, M D (1) M12, 5p, M E (1) M12, 5p, M D (1) M12, 5p, M LS_H LS; LS_K; NOTE: These connectors are dedicated to a communication BUS of the Master/ Slave chain, it is not permissible to access the lines, always use cord sets. 56

57 accessories ST20* / outfit mounting accessories product to used with dimensions (mm) description / installation foto LS series L Bracket Supplied as standard, pieces to couple to the length from 00 to 1,050, 6 pieces for the length from 1,200 to 1, LS series M5 Insert with threaded bolts and nuts Supplied as standard, in a number corresponding to the brackets. outfit brackets mounting LS; LS_K; LS_H 57

58 dimensions (mm) IP69K L1 L2 ø L L La barriera viene fornita già montata all interno della custodia trasparente. Il cavo di alimentazione ha una lunghezza standard di 10 metri e un diametro massimo di 6 mm. Le staffe sono incluse. models ,050 1,200 1,50 1,500 2B B B L1 dimensions ,070 1,220 1,70 1, ,060 1,160 L2 dimensions , ,0 1,90 1, ,00 1,10 L dimensions (± ) (mm) , ,515 1, ,055 1,155 L dimensions (mm) , ,57 1, ,077 1,177 LS; LS_K; LS_H 58

59 LPER series Light Curtains Type features Type according IEC and IEC Robust housing (50x60 mm) for applications in presence of heavy shocks and vibrations 0 mm resolution for hand protection and 2,, beams for body protection/access control Operating distance up to 16 m (standard version) and up to 60 m (LONG RANGE version) Integrated functions: MANUAL/AUTOMATIC Restart, EDM and operating distance selectable Standard M12 5 poles connector on TX unit and M12 8 poles or M2 9 poles on RX unit Light Curtains Type download area Application notes Photos Catalogue / Manuals code description series couple beams height range LP ER 0 0A 0B 0C L 12 Type safety light curtains 50 x 60 mm compact housing Emitter + Receiver couple 0 mm resolution; hand protection 2 beams resolution; body protection; 500 mm controlled height beams resolution; body protection; 800 mm controlled height beams resolution; body protection; 900 mm controlled height Protected height from 500 to 1,200 mm Standard model with selectable MANUAL/AUTOMATIC Restart and EDM functions Long range model Model with M12 connector on receiver unit LP ER / available models 2,, beams resolution; / m controlled distance; 7 msec responce time available models 0 mm resolution; / m controlled distance altezza protected ottica height (mm) (mm) n n of raggi beams modelli altezza protected ottica height (mm) (mm) n n of raggi beams tempo response di risposta time (msec) modelli LPER/0A LPER/0-050L 810 LPER/0B LPER/0-090L 910 LPER/0C , , LPER/0-120L LPER 59

60 available models 2,, beams resolution; / m controlled distance altezza protected ottica height (mm) (mm) response time n n of raggi beams dist. tra i raggi (msec) modelli LPER/0A-050L LPER/0A-050L12 LPER/0B-080L LPER/0B-080L12 LPER/0C-090L LPER/0C-090L12 technical specifications type in according to EN / IEC /-2 LPER/**-***-- tensione power di alimentazione supply Vdc Vcc power potenza consumption, assorbita, Ricevitore Receiver potenza power consumption, assorbita, Emettitore Emitter tipo output di uscita type corrente output current di uscita carico equivalent resistivo resistive equivalente load carico capacitive capacitivo load tollerato ritardo recovery alla disponibilità time tempo response di risposta time OSSDs durata impulso di OSSDs self test pulse duration autotest uscite OSSDs durata restart comando signal duration restart durata Test segnale signal di duration ingresso Test angolo effective di apertura aperture effettivo angle (EAA) immunità artificial light luce rejection artificiale immunità ambient light luce rejection naturale grado IP di protection protezione IP operating temperatura temperature di lavoro temperatura storage di immagazzinamento temperature humidity umidità resistenza vibrations alle vibrazioni shocks urti sezione dimension corpo connettori S0 connectors S0 emettitori Emitter 19,2...28, W W 2 x PNP 500 ma 8 Ω 2 µf 15 s 0 ms 100 µs 100 ms 0 ms ± 2,5 according secondo to IEC IEC according secondo to IEC IEC IP C C 95% according secondo to IEC IEC according secondo to IEC IEC mm mm (frontale) (front) x 60 mm 1 1 x M12 x M12 5p 5p maschio male PELV power supplier according to EN Cap.6. no load OSSD safety outputs higher values are considered overload lower values are considered short circuit lower values may be considered short circuit IEC , 200 according to the reported standards without any additional precaution the device can t be used for outdoor applications no condensation to be respected also during transportation no condensation according to the reported standards painted aluminium RAL 1012 S0 connettori connectors S0 ricevitori Receiver 1x 1x M2, 19p, 19p, maschio male 1x 1x M12, M12, 8p, 8p, maschio male (L12 (modelli male) L12) LPER 60

61 safety parameters LPER/0-***L LPER/**-*** 0A-050 0B-080 0C-090 altezza height (mm) distanza height tra i raggi (mm) number numero of raggi beams number numero of raggi beams 2 tempo response di risposta time (ms) (ms) ,5 tempo response di risposta time (ms) type tipo (1) (1) type tipo (1) SIL (2) SIL (2) SILCL () SILCL () PL () e PL () e PFHd 1,02E-08 1,17E-08 1,2E-08 PFHd 7,5E-09 7,70E-09 7,87E-09 DCavg 98,7% 98,9% 98,57% DCavg 97,9% 97,99% 98,0% MTTFd (years) (anni) CFF % MTTFd (years) (anni) CFF % (1) ref. CEI EN :2005; CEI EN :2007 (2) ref. CEI EN 61508:2002 () ref. CEI EN 62061: CEI EN 62061/EC2:2008 () ref. UNI EN ISO 189-1:2008 LPER/**-***L 0A-050 0B-080 0C-090 LPER/**-***L12 0A-050 0B-080 0C-090 distanza height tra i raggi (mm) distanza height tra i raggi (mm) number numero of raggi beams 2 number numero of raggi beams 2 tempo response di risposta time (ms) (ms) tempo response di risposta time (ms) (ms) type tipo (1) type tipo (1) SIL (2) SIL (2) SILCL () SILCL () PL () e PL () e PFHd DCavg MTTFd (years) (anni) 7,5E E-09 7,70E E-09 7,87E E-09 97,9% 97.9% 97,99% 97.99% 98,0% 98.0% 100 PFHd DCavg MTTFd (years) (anni) 7,5E E-09 7,70E E-09 7,87E E-09 97,9% 97.9% 97,99% 97.99% 98,0% 98.0% 100 CFF CFF 80% 80% CFF 80% electrical diagrams of the connections LPER serie LPER series M12 (5 (5 poli poles maschio maletx unità unit) TX) pin colore segnale signal type tipo descrizione description 1 BN 2V CC DC POWER ingresso power supply alimentazione input 2 WH portata range H/Test IN ingresso selection selezione input BU 0V POWER riferimento supply voltage di alimentazione reference s0 BK portata range H/Test IN ingresso selection selezione input 5 GY PE GND protezione protection di earth terra LPER/ **-***_ selezione della possible portata combinations con i livelli logici dei pin pin 2 pin funzione function selezionata LO LO LO test test (nessuna (no emission) emissione) LO HI emissione with con high portata range alta BK BN RD YE WH black brown red yellow white OG GN BU GY VT orange green blue grey violet HI LO emissione con with portata low range bassa HI HI HI non not ammessa admitted PK pink LPER The Test contact is necessary only if the entire safety chain of the receiver downstream must be tested. If the Test is not necessary replace the TEST contact with direct wiring at 2 V DC. 61

62 LPER serie LPER series M2 (19 (19 poli poles maschio male RX unità unit) RX) pin colore segnale signal type tipo descrizione description 1 WH N.C. - not non connected connesso LPER/**-*** LPER/**-***L 2 RD OSSD2 OUT seconda uscita safety statica di output sicurezza (PNP) (PNP) GY OSSD1 OUT prima first uscita safety statica di output sicurezza (PNP) (PNP) YE System Status + repetition ripetizione of OSSDs stato OSSD, status, vedi see nota note Sign. levlel OUT + indicazione low signal level segnale indication, basso, see vedi note nota 5 GN N.C. - a b not non connected connesso 6 BU 0V CC POWER riferimento supply della voltage tensione reference di alimentazione 7 VT N.C. - not non connected connesso 8 GY - PK N.C. - not non connected connesso 9 RD - BU N.C. - not non connected connesso 10 WH - GN N.C. - not non connected connesso 11 BK Abilitaz. EDM IN abilitazione enabling al for controllo external dei contactor contattori control esterni 12 WH - GN PE GND connessione earth protection della protezione connection di terra 1 WH - YE Man. / Autom. IN selezione selection della of the modalità Start/Restart di Avvio/Riavvio mode 1 BN - YE avvio start IN connessione connection al to pulsante the Start/Restart di Avvio/Riavvio button 15 WH - GY N.C. - not non connected connesso 16 BN - GY N.C. - not non connected connesso 17 WH - PK N.C. - not non connected connesso BK BN black brown OG GN orange green YE WH yellow white GY VT grey violet 18 BN - GN EDM IN connection connessione to ai the contatti external di controllo contacts esterni RD red BU blue PK pink 19 BN 2V CC POWER ingresso supply tensione voltage di alimentazione input serie LPER M12 (8 (8 poli poles maschio male RX unità unit RX L12 modelli models) L12) pin colore segnale signal type tipo descrizione description 1 WH OSSD1 OUT prima first uscita safety statica di output sicurezza (PNP) (PNP) s LPER/0*-***L12 2 BN 2V CC POWER tensione supply di alimentazione voltage GN OSSD2 OUT seconda uscita safety statica di output sicurezza (PNP) (PNP) YE EDM IN connection connessione to ai the contatti external di controllo contacts esterni (EDM) o or connesso connected a 0V at per 0V to esclusione exclude EDM 5 GY Mode_A IN selection of the manual or selezione della modalità di Avvio/Riavvio/EDM automatic Start/Restart mode 6 PK Mode_B IN selection of the manual or selezione della modalità di Avvio/Riavvio/EDM automatic Start/Restart mode 7 BU 0V POWER riferimento supply della voltage tensione reference di alimentzione 8 RD FE GND terra protection di protezione earth NOTE: On these models it is possible to choose the operating modes by changing the wiring. By using the EDM function it is possible to extend the safety control to the contactors controlled downstream, that must be the type with guided contacts and approved for safety applications. LPER 62

63 dimensions (mm) LPER/0-***L, LPER/0*-*** - Ricevitore Receiver 18 A 78 C 50 M2 B LPER/0-***L12, LPER/0*-***L, LPER/0*-***L12 - Emettitore - Emitter 8 60 M12 50 dimensioni dimensions (mm) LPER/**-*** LPER/**-***L 0A-050 0B-080 0C A-050 0B-080 0C-090 A (TX) 76 1, , , , , , B (protected (altezza protetta) height) 510* 810* 910* , * 810* 910* C (posizione C (first beam primo quote) raggio) LPER 6

64 accessories ST20 / outfit mounting accessories product to be used with dimensions (mm) description / installation stainless steel plate M6 foto LP series 50 0 M ø Fastening insert for 50x60 profile. Part of the standard kit Two pieces are provided for each bracket ST ST202 / outfit mounting accessories product to be used with dimensions (mm) description / installation foto LP series L Bracket Long bracket. Part of the standard kit. Two pieces are provided for each couples. Must be applied in the housin part of the body LPER 6

65 LPPF series Light Curtains Type features Type according IEC and IEC Robust housing (50x60 mm) for applications in presence of heavy shocks and vibrations Complete passive unit made by pre-mounted and pre-aligned integrated mirrors Protected height 500, 800 an 900 mm Resolutions 2,, beams for body protection / access control Integrated functions: MANUAL/AUTOMATIC Restart and EDM Operating distance up to 6 m M12 8 polse standard connector Light Curtains Type download area Application notes Photos Catalogue / Manuals code description series couple beams protected height LP PF 0A 0B 0C Type safety light curtains 50 x 60 mm compact housing M12 connecored active element + passive element couple 2 beams resolution; body protection; 500 mm protected height beams resolution; body protection; 800 mm protected height beams resolution; body protection; 900 mm protected height 500 mm protected height 800 mm protected height 900 mm protected height LP PF / 0A available models m controlled distance; 7 msec response time altezza protected ottica height (mm) (mm) n n of raggi beams dist. tra between i raggi beams (mm) (mm) modelli LPPF/0A-050 LPPF/ LPPF/0C-090 LPPF 65

66 technical specifications type according to EN / IEC /-2 LPPF/**-*** tensione power di alimentazione supply Vdc Vcc power potenza consumption, assorbita, Ricevitore Receiver potenza power consumption, assorbita, Emettitore Emitter tipo output di uscita type corrente output current di uscita carico equivalent resistivo resistive equivalente load carico capacitive capacitivo load tollerato ritardo recovery alla disponibilità time tempo response di risposta time (OSSDs OFF) angolo effective di apertura aperture effettivo angle (EAA) immunità artificial light luce rejection artificiale immunità ambient light luce rejection naturale grado IP di protection protezione IP temp. operating di lav. senza temperature condensa temperatura storage di immagazzinamento temperature humidity (no umidità condensation) resistenza vibrations alle vibrazioni shocks urti lunghezza max totale cable cavi length alim. / uscita (power supply/outputs) sezione corpo dimension connettore connector S0 unita active attiva unit 19,2...28, W W 2 x PNP 500 ma 8 Ω 2 µf 15 s 0 ms ± 2,5 2.5 according secondo to IEC IEC according secondo to IEC IEC IP C C 95% 95% (no condensation) (senza condensa) according secondo to IEC IEC according secondo to IEC IEC m 100 m 50 mm (frontale) 50 mm x (front) 60 mmx 60 mm 1 1 x M12 x M12 8p 8p maschio male PELV power supplier according to EN Cap.6. no load OSSD safety outputs higher values are considered overload lower values are considered short circuit lower values may be considered short circuit IEC , 200 according to the reported standards without any additional precaution the device can t be used for outdoor applications no condensation to be respected also during transportation no condensation according to the reported standards cable section 0. mm2 (to respect max length) painted aluminium RAL 1012 PVC sheath, ø 5.5 mm L 10 m, 0. mm2 safety parameters LPPF/**-***_ dist. between tra i raggi beams (mm) number numero of raggi beams tempo response di risposta time (ms) (ms) type Tipo (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd (years) (anni) CFF 0A-050 0B-080 0C e,8e-09.8e-09,92e-09.92e-09 5,01E E-09 98,1% 98.1% 98,16% 98.16% 98,19% 98.19% % (1) ref. CEI EN :2005; CEI EN :2007 (2) ref. CEI EN 61508:2002 () ref. CEI EN 62061: CEI EN 62061/EC2:2008 () ref. UNI EN ISO 189-1:2008 LPPF 66

67 electrical diagrams of the connections LPPF serie LPPF series M12 (8 (8 poli poles maschio male active unità attiva) unit) BK BN black brown OG GN orange green RD red BU blue YE yellow GY grey WH PK VT dimensions (mm) LPPF / **-*** white pink violet pin colore segnale signal type tipo descrizione description 1 WH OSSD1 OUT prima first uscita safety statica di output sicurezza (PNP) (PNP) 2 BN 2V CC POWER tensione supply di alimentazione voltage GN OSSD2 OUT seconda uscita safety statica di output sicurezza (PNP) (PNP) YE EDM IN 5 GY Mode_A IN 6 PK Mode_B IN connessione connection to ai the contatti external di controllo contacts esterni (EDM) o connesso or connected a 0V at per 0V esclusione to exclude EDM selezione selection della modalità of the manual di Avvio or / Riavvio automatic manuale Start/Restart o automatico mode selezione selection della modalità of the manual di Avvio/Riavvio or automatic manuale Start/Restart o automatico mode 7 BU 0V POWER riferimento supply della voltage tensione reference di alimentazione 8 RD FE GND protection terra funzionale earth NOTE: On these models it is possible to choose the operating modes by changing the wiring. By using the EDM function it is possible to extend the safety control to the contactors controlled downstream, that must be the type with guided contacts and approved for safety applications LPPF/0A (passive unit) (active unit) 60 LPPF/0B-080 1,02 50 (passive unit) 60 1, (active unit) 60 LPPF 67

68 LPPF/0C-090 1,12 50 (passive unit) 60 1, (active unit) 60 accessories ST20 / outfit mounting accessories product to be used with dimensions (mm) description / installation stainless steel plate M6 foto LP series 50 0 M ø Fastening insert for 50x60 profile. Part of the standard kit Two pieces are provided for each bracket ST ST202 / outfit mounting accessories product to be used with dimensions (mm) description / installation foto LP series L Bracket Long bracket. Part of the standard kit. Two pieces are provided for each couples. Must be applied in the housin part of the body LPPF 68

69 LPER_M series Light curtains Type features Type according IEC and IEC Robust housing (50 x 60 mm) for applications in presence of heavy shocks and vibrations 0 and 0 mm hand protection, 90 mm presence control and 2,, beams body protection/access control Protected height from 00 mm up to 1800 mm Integrated unctions: AUTOMATIC/MANUAL Restart, EDM, range reduction selectable Muting and Override function selectable through dedicate wires M12 5 poles and M2 19 poles standard connectors Light curtains Type download area Application notes Photos Catalogue / Manuals code description LP R / 0-00 M L series couple beam height muting range LP ER A 0B 0C M L Type Safety light Curtains 50 x 60 mm compact housing Emitter + Receiver couple 0 mm resolution, hand protection 0 mm resolution, hand protection 90 mm resolution, presence control 2 beam resolution, body protection, 500 mm protected height beam resolution, body protection, 800 mm protected height beam resolution, body protection, 900 mm protected height Protected height from 00 to 1,800 mm Integrated Muting function for Muting sensors Long range LPER_M 69

70 available models 0 mm resolution; / m controlled distance available models 90 mm resolution; / m controlled distance altezza protected ottica height (mm) (mm) n n of raggi beams tempo response di risposta time (msec) (msec) modelli altezza protected ottica height (mm) (mm) n n of raggi beams tempo response di risposta time (msec) modelli LPER/0-00M LPER/90-00M LPER/0-05M LPER/90-05M LPER/0-060M LPER/90-060M LPER/0-075M LPER/90-075M LPER/0-090M , LPER/90-090M , LPER/0-105M , LPER/90-105M , LPER/0-120M , LPER/90-120M available models 0 mm resolution; / m controlled distance , , , , LPER/90-15M LPER/90-150M LPER/90-165M altezza protected ottica tempo response di risposta n n of raggi beams height (mm) (mm) time (msec) , modelli LPER/0-00M LPER/0-05M , LPER/90-180M available models 7 msec response time; / m controlled distance LPER/0-060M LPER/0-075M altezza protected ottica height (mm) (mm) n n of raggi beams dist. response tra i raggi time (mm) (msec) modelli LPER/0-090M LPER/0A-050M , LPER/0-105M LPER/0B-080M , LPER/0-120M LPER/0C-090M , , , LPER/0-15M LPER/0-150M LPER/0-165M available models 7 msec responce time; / m controlled distance , , LPER/0-180M altezza protected ottica height (mm) (mm) n n of raggi beams dist. response tra i raggi time (mm) (msec) modelli available models 0 mm resolution; / m controlled distance altezza protected ottica tempo response di risposta n n of raggi beams modelli height (mm) (mm) time (msec) LPER/0A-050ML LPER/0B-080ML LPER/0C-090ML , ,5 LPER/0-060ML LPER/0-090ML LPER/0-120ML LPER_M 70

71 technical specifications type according to EN / IEC /-2 LPER / **-***M- tensione power di alimentazione supply Vdc Vcc power potenza consumption, assorbita, Ricevitore Receiver potenza power consumption, assorbita, Emettitore Emitter tipo output di uscita type corrente output current di uscita carico equivalent resistivo resistive equivalente load carico capacitive capacitivo load tollerato ritardo recovery alla disponibilità time tempo response di risposta time OSSDs angolo effective di apertura aperture effettivo angle (EAA) immunità artificial light luce rejection artificiale immunità ambient light luce rejection naturale grado IP di protection protezione IP operating temperatura temperature di lavoro temperatura storage di immagazzinamento temperature humidity umidità resistenza vibrations alle vibrazioni resistenza shocks agli urti lunghezza max totale cable cavi length alimentazione supply/outputs) / uscita (power sezione dimension corpo connettori S0 connectors S0 emettitori Emitter S0 connettori connectors S0 ricevitori Receiver S1 and S2 connectors connettori S1 e S2 (o S1) ricevitori (or S1) receiver 19,2...28, W W 2 x PNP 500 ma 8 Ω 2 µf 15 s 0 ms ± 2,5 2.5 according secondo to IEC IEC according secondo to IEC IEC IP C C 95% according secondo to IEC IEC according secondo to IEC IEC m mm mm (frontale) (front) x 60 mm 1 x M12, 5p maschio, male, nickel-plated ottone nichelato brass 1x M2, 19p, maschio, male, nickel-plated ottone nichelato brass 2/1 M12 5p 5p femmina female PELV power supplier according to EN Cap.6. no load OSSD safety outputs higher values are considered overload lower values are considered short circuit lower values may be considered short circuit IEC , 200 according to the reported standards without any additional precaution the device can t be used for outdoor applications no condensation to be respected also during transportation no condensation according to the reported standards painted aluminium RAL 1012 LPER_M 71

72 safety parameters LPER/0-***M altezza height (mm) number numero of raggi beams tempo response di risposta time (ms) Type Tipo (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd (years) (anni) CFF , e 9,06E E-09 9,89E E-06 1,09E E-08 1,18E E-08 1,28E E-08 1,7E E-08 1,6E E-08 98,2% 98.2% 98,5% 98.5% 98,% 98.% 98,50% 98.50% 98,55% 98.55% 98,56% 98.56% 98,6% 98.6% % (1) ref. CEI EN :2005; CEI EN :2007 (2) ref. CEI EN 61508:2002 () ref. CEI EN 62061: CEI EN 62061/EC2:2008 () ref. UNI EN ISO 189-1:2008 LPER/0-***M altezza height (mm) number numero of raggi beams tempo response di risposta time (ms) Type Tipo (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd (years) (anni) CFF , , , , , , , ,5 e 8,71E E-09 9,5E E-09 1,02E E-08 1,10E E-08 1,17E E-08 1,25E E-08 1,2E E-08 1,0E E-08 1,7E E-08 1,55E E-08 1,62E E-08 98,19% 98.19% 98,29% 98.29% 98,7% 98.7% 98,% 98.% 98,9% 98.9% 98,5% 98.5% 98,57% 98.57% 98,60% 98.60% 98,6% 98.6% 98,65% 98.65% 98,67% 98.67% % LPER/0-***ML altezza height (mm) number numero of raggi beams tempo response di risposta time (ms) Type Tipo (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd (years) (anni) CFF , , e 1,02E E-08 1,17E E-08 1,2E E-08 98,7% 98.7% 98,9% 98.9% 98,57% 98.57% % LPER_M 72

73 LPER/90-***M altezza height (mm) number numero of raggi beams tempo response di risposta time (ms) Type Tipo (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd (years) (anni) CFF , , , , , , , , e 8,91E E-09 9,8E E-09 1,01E E-08 1,06E E-08 1,12E E-08 1,18E E-08 1,2E E-08 1,29E E-08 1,5E E-08 1,1E E E-08 1,7E % 98,22% 98,0% 98.0% 98,6% 98.6% 98,1% 98.1% 98,6% 98.6% 98,50% 98.50% 98,5% 98.5% 98,56% 98.56% 98,58% 98.58% 98,61% 98.61% 98,6% 98.6% % LPER/**-***M distanza dist. between tra i raggi beams (mm) number numero of raggi beams tempo response di risposta time (ms) Type Tipo (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd (years) (anni) CFF 0A-050 0B-080 0C e 7,5E E-09 7,70E E-09 7,87E E-09 97,9% 97.9% 97,99% 97.99% 98,0% 98.0% % LPER/**-***ML distanza dist. between tra i raggi beams (mm) number numero of raggi beams tempo response di risposta time (ms) Type Tipo (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd (years) (anni) CFF 0A-050 0B-080 0C e 7,5E E-09 7,70E E-09 7,87E E-09 97,9% 97.9% 97,99% 97.99% 98,0% 98.0% % LPER_M 7

74 electrical diagrams of the connections LPER_M serie LPER_M series M12 (5 (5 poli poles maschio male unit) unità) pin colore segnale signal type tipo descrizione description 1 BN 2V DC CC POWER ingresso power supply alimentazione input 2 WH portata range H/Test / IN ingresso selection selezione input BU 0 0VV POWER riferimento supply voltage di alimentazione reference s0 BK portata range H/Test / IN ingresso selection selezione input 5 GY PE GND protezione protection di earth terra LPER/ **-***_ selezione della possible portata combinations con i livelli logici dei pin pin 2 pin funzione function selezionata 5 LO LO LO test test (nessuna (no emission) emissione) BK BN black brown OG GN orange green 1 2 LO HI emissione with con high portata range alta HI emissione con portata LO emission with low range bassa RD YE WH red yellow white BU GY VT blue grey violet HI HI HI non not ammessa admitted PK pink levels: livelli: LO = <5 5 V o or aperto; open; HI HI = 11 0 to 0 V V The Test contact is necessary only if the entire safety chain of the receiver downstream must be tested. If the Test is not necessary replace the TEST contact with direct wiring at 2 V DC. Receiver receiver s0 s s BN (2V) WH BU (0V) BK GY 1 R Sens_2 s2 1 5 R Sens_ pin colore segnale signal type tipo funzione function levels livelli 1 BN 2VV CC DC POWER uscita supply tensione voltage di alimentazione output corrente max. total uscita output totale current: Max.:100 ma 2 WH sens_1 IN ingresso muting sensore 1 di muting input 1 LO: < <5V 5 V o or aperto; open; HI: to 0 VV BU 0 0VV CC DC POWER riferimento power supply di alimentazione reference - BK sens_ IN ingresso muting sensore di muting input ingresso input selection selezione 5 GY PE GND protezione earth protection di terra LO: < <5V 5 V o or aperto; open; HI: to 0 VV livelli: LO: LO < = 5 V 5 or V o open; aperto; HI: HI 11 = to V V NOTE: The sensors can be of any type, the output level must be high when there is material (HI). LPER_M 7

75 LPER serie LPER series M2 (19 (19 poli poles maschio male RX unità unit) RX) pin colore segnale signal type tipo descrizione description 1 WH Lamp. lampada esterna accesa - output for piloting the external Muting Lamp Muting indica muting in corso 2 RD OSSD2 OUT seconda uscita safety statica di output sicurezza (PNP) (PNP) GY OSSD1 OUT prima first uscita safety statica di output sicurezza (PNP) (PNP) YE System Status + repetition ripetizione of OSSDs stato OSSD, status, vedi see nota note Sign. levlel OUT + indicazione low signal level segnale indication, basso, see vedi note nota 5 GN N.C. - a b indica active Muting with Muting, corso, non HI:Muting connesso Muting; ON; LO:Muting NO Muting OFF 6 BU 0V DC CC POWER riferimento supply della voltage tensione reference di alimentazione NOTA:Il NOTE: The Il segnale Muting di Enabling Abilitazione signal Muting (pin (pin 15) must 15) deve be LO essere before the LO prima HI enabling del segnale signal di of abilitazione the single HI sensors, dei singoli and sensori, it must remain e deve low rimanere for the entire basso duration per tutta of la the durata sensor del enabling consenso signal, dei otherwise sensori, in Muting caso contrario will stop. il Muting The System si interrompe. Status output signal (pin Il segnale ) repeats di uscita the state di System of the Status OSSD (pin outputs, ) ripete HI= lo safety stato light curtain delle uscite ON, OSSD, LO= safety HI= barriera light curtain ON, OFF; LO=barriera on models OFF; in nei which modelli the signal in cui level è presente indication l indicazione is present, the di livello output segnale, status is momentarily lo stato di denied uscita viene with a momentaneamente pulse lasting 15 to negato 5ms con and un period 800ms impulso if di the durata signal ms 15 5ms is weak. e periodo 800ms se il segnale risulta debole. 7 VT Mode_0 - ingresso di configurazione input config. for the other models with Muting per gli altri modelli con muting 8 GY - PK Mode_1 - ingresso di configurazione input config. for the other models with Muting per gli altri modelli con muting 9 RD - BU Mode_2 - ingresso di configurazione input config. for the other models with Muting per tutti i modelli con muting 10 WH - GN Mode_ - ingresso di configurazione input config. for the other models with Muting per tutti i modelli con muting 11 BK Abilitaz. EDM IN abilitazione enabling al for controllo external dei contactor contattori control esterni 12 WH - GN PE GND connessione earth protection della protezione connection di terra 1 WH - YE Man. / Autom. IN selezione selection della of the modalità Start/Restart di Avvio/Riavvio mode 1 BN - YE avvio start IN selezione connection della to modalità the Start/Restart di Avvio/Riavvio button BK black OG orange 15 WH - GY N.C. - not non connected connesso BN brown GN green 16 BN - GY override_1 - ingresso input 1 for per the il comando forced control forzato of Muting di RD YE red yellow BU GY blue grey 17 WH - PK override_2 - ingresso input 2 for per the il comando forced control forzato of Muting di WH white VT violet 18 BN - GN EDM IN connection connessione to ai the contatti external di controllo contacts esterni PK pink 19 BN 2V DC CC POWER ingresso supply tensione voltage di alimentazione input Receiver receiver s0 s s BN (2V) WH BU (0V) BK GY 1 R Sens_2 s2 1 5 R Sens_ pin colore segnale signal type tipo funzione function levels livelli 1 BN 2VV CC DC POWER uscita supply tensione voltage di alimentazione output corrente max. total uscita output totale current: Max.:100 ma 2 WH sens_2 IN ingresso muting sensore 2 di muting input 2 LO: < <5V 5 V o or aperto; open; HI: to V V BU 0 0VV CC DC POWER riferimento power supply di alimentazione reference - BK sens_ IN ingresso muting sensore di muting input ingresso input selection selezione 5 GY PE GND protezione earth protection di terra LO: < <5V 5 V o or aperto; open; HI: to V V livelli: LO: LO < = 5 V 5 or V o open; aperto; HI: HI 11 = to V V NOTE: The sensors can be of any type, the output level must be high when there is material (HI). LPER_M 75

76 dimensions (mm) LPER/**-***M - Ricevitore Receiver 18 B 78 C 50 M2 B LPER/**-***M - Emettitore - Emitter 8 60 M12 50 dimensions dimensioni LPER/**-***M LPER/**-***ML A 0B 0C 0A 0B 0C A (TX) , , , , , , , , , , ,16 A (RX) , , , , , , , , , , ,176 B (protected (altezza protetta) height) , ,210 1, , , , * 810* 910* 510* 810* 910* LPER_M (posizione primo C (first beam quote) raggio) 76

77 accessories ST20 / outfit mounting accessories product to be used with dimensions (mm) description / installation stainless steel plate M6 foto LP series 50 0 M ø Fastening insert for 50x60 profile. Part of the standard kit Two pieces are provided for each bracket ST ST202 / outfit mounting accessories product to be used with dimensions (mm) description / installation foto LP series L Bracket Long bracket. Part of the standard kit. Two pieces are provided for each couples. Must be applied in the housin part of the body LPER_M 77

78 notes LPER_M 78

79 features LPPT series Light Curtains Type Type according IEC and IEC Robust housing (50x60 mm) for applications in presence of heavy shocks and vibrations Complete passive unit made by pre-mounted and pre-aligned integrated mirrors Protected height 500, 800 an 900 mm Resolutions 2,, beams for body protection / access control Integrated functions: MANUAL/AUTOMATIC Restart and EDM Operating distance up to 6 m Muting and Override function selectable through dedicate wires M12 5 poles and M2 19 poles standard connectors Light Curtains Type download area Application notes Photos Catalogue / Manuals code description series couple beams height muting LP PT 0A 0B 0C M2 M Type safety light curtains 50 x 60 mm compact housing M12 connecored active element + passive element couple 2 beams resolution; body protection; 500 mm protected height beams resolution; body protection; 800 mm protected height beams resolution; body protection; 900 mm protected height 500 mm protected height 800 mm protected height 900 mm protected height Integrated Muting function for 2 Muting sensors Integrated Muting function for Muting sensors LP PT / 0A M2 available models m controlled distance; 10 ms response time altezza protected ottica height (mm) (mm) n n of raggi beams dist. response tra i raggi time (mm) modelli LPPT/0A-050M2 LPPT/0A-050M LPPT/0B-080M2 LPPT/0B-080M LPPT/0C-090M2 LPPT/0C-090M LPPT 79

80 technical specifications Type according to EN / IEC /-2 LPPT tensione power di alimentazione supply Vdc Vcc power potenza consumption, assorbita, Ricevitore Receiver potenza power consumption, assorbita, Emettitore Emitter tipo output di uscita type corrente output current di uscita carico equivalent resistivo resistive equivalente load carico capacitive capacitivo load tollerato ritardo recovery alla disponibilità time tempo response di risposta time OSSDs angolo effective di apertura aperture effettivo angle (EAA) immunità artificial light luce rejection artificiale immunità ambient light luce rejection naturale grado IP di protection protezione IP operating temperatura temperature di lavoro temperatura storage di immagazzinamento temperature humidity umidità resistenza vibrations alle vibrazioni resistenza shocks agli urti use uso of di deflection specchi deviatori mirrors fattori ambient ambientali factors lunghezza max cable totale length cavi (power alimentazione supply/outputs) / uscita sezione section corpo body connettore S0 connector S0 S1 connettore or S2 connector S1 e S2 (or(o S1 S1) only) 19,2...28, W W 2 x PNP 500 ma 8 Ω 2 µf 15 s 0 ms ± 2,5 2.5 according secondo to IEC IEC according secondo to IEC IEC IP C C 95% according secondo to IEC IEC according secondo to IEC IEC , ,50 / , m mm (frontale) (front) x x mm mm 1x M2, 19p, maschio, male, nickel-plated ottone nichelato brass 2/1 M12 5p femmina female PELV power supplier according to EN Cap.6. no load OSSD safety outputs higher values are considered overload lower values are considered short circuit lower values may be considered short circuit IEC , 200 according to the reported standards without any additional precaution the device can t be used for outdoor applications no condensation to be respected also during transportation no condensation according to the reported standards painted aluminium RAL 1012 safety parameters LPPT/**-***M2 (M) dist. distanza between tra i beams raggi number numero of raggi beams tempo response di risposta time (ms) Type tipo (1) (1) SIL (2) SILCL () PL () PFHd DCavg MTTFd (years) (anni) CFF 0A-050 0B-080 0C e,8e-09.8e-09,92e-09.92e-09 5,01E E-09 98,1% 98.1% 98,16% 98.16% 98,19% 98.19% % LPPT (1) ref. CEI EN :2005; CEI EN :2007 (2) ref. CEI EN 61508:2002 () ref. CEI EN 62061: CEI EN 62061/EC2:2008 () ref. UNI EN ISO 189-1:

81 electrical diagrams of the connections LPER serie LPER LPPT series M2, S0 (19 (19 poli poles (19 maschio poli male maschio) RX unità unit) RX) pin colore segnale signal type tipo descrizione description 1 WH Lamp. lampada esterna accesa - output for piloting the external Muting Lamp Muting indica muting in corso 2 RD OSSD2 OUT seconda second uscita safety statica di output sicurezza (PNP) (PNP) GY OSSD1 OUT prima first uscita safety statica di output sicurezza (PNP) (PNP) YE System Status + repetition ripetizione of OSSDs stato OSSD, status, vedi see nota note Sign. levlel OUT + indicazione low signal level segnale indication, basso, see vedi note nota 5 GN stato N.C. muting OUT indica muting in corso, HI: muting; active with Muting, HI: Muting ON; LO: Muting OFF LO: NO muting 6 BU 0VV CC DC POWER riferimento supply della voltage tensione reference di alimentazione 7 VT sensore_1 Mode_0 IN- input ingresso config. sensori for the di other muting models (modelli with Muting M2) 8 GY - PK sensore_2 Mode_1 IN- input ingresso config. sensori for the di other muting models (modelli with Muting M2) NOTA:Il segnale di Abilitazione Muting (pin 15) deve essere LO prima del segnale di abilitazione HI dei singoli sensori, e deve ri- manere basso per tutta la durata del consenso dei sensori, in caso contrario il NOTA:Il NOTE: Muting The segnale si Muting interrompe. di Enabling Abilitazione signal Muting (pin (pin 15) must 15) deve be LO essere before the LO Il segnale prima HI enabling del di segnale uscita signal di di of System abilitazione the single Status HI sensors, (pin dei ) singoli ripete and sensori, it lo must remain e stato deve low delle rimanere for uscite the entire basso OSSD, duration per HI= tutta barriera of la the durata sensor ON, del LO=barriera enabling consenso signal, dei otherwise sensori, OFF; nei in Muting caso modelli contrario will in cui stop. è il presente Muting The System si l indicazione interrompe. Status output di livel-signalo segnale, ) repeats di uscita lo the stato state di di System uscita of the Status viene OSSD momentaneamente (pin outputs, ) ripete HI= lo safety stato light (pin Il segnale curtain delle negato uscite ON, con OSSD, LO= un impulso safety HI= barriera light di durata curtain ON, 15 5ms OFF; LO=barriera on e models periodo OFF; in nei which modelli the 800ms signal in se cui level il segnale è presente indication risulta l indicazione present, debole. the di livello output segnale, status is momentarily lo stato di denied uscita viene with a momentaneamente pulse lasting 15 to negato 5ms con and un period 800ms impulso if di the durata signal 15 5ms is weak e periodo 800ms se il segnale risulta debole. BK BN black brown OG GN orange green 9 RD - BU Mode_2 IN- ingresso di configurazione input config. for the other models with Muting per tutti i modelli con muting 10 WH - GN Mode_ IN- ingresso di configurazione input config. for the other models with Muting per tutti i modelli con muting 11 BK Abilitaz. EDM IN abilitazione enabling al for controllo external dei contactor contattori control esterni 12 WH - GN PE GND connessione earth protection della protezione connection di terra 1 WH - YE Man. / Autom. IN selezione selection della of the modalità Start / Restart di Avvio/Riavvio mode 1 BN - YE avvio start IN selezione connection della to the modalità Start / di Restart Avvio/Riavvio button 15 WH - GY Abilitaz. N.C. muting IN- ingresso di abilitazione not connected del Muting, vedi nota 16 BN - GY override_1 IN- ingresso input 11 for per the il comando forced control forzato of Muting di Muting RD YE red yellow BU GY blue grey 17 WH - PK override_2 IN- ingresso input 22 for per the il comando forced control forzato of Muting di Muting WH white VT violet 18 BN - GN EDM IN connection connessione to ai the contatti external di controllo contacts esterni PK pink 19 BN 2VV CC DC POWER ingresso supply tensione voltage di alimentazione input Receiver receiver s0 s s2 BN (2V) 1 WH 2 BU (0V) BK GY 5 1 R Sens_2 s2 1 R 5 Sens_ pin colore segnale signal type tipo funzione function levels livelli 1 BN 2VV CC DC POWER uscita supply tensione voltage di alimentazione output corrente max. total uscita output totale current: Max.:100 ma 2 WH sens_1 IN ingresso muting sensore 1 di input muting 1 LO: < <5V 5 or aperto; open; HI: 11 0 to 0 V BU 0VV CC DC POWER riferimento power supply di alimentazione reference - BK sens_ IN ingresso muting sensore di input muting LO: <5V input o aperto; selection HI: 11 0 V 5 GY PE GND protezione earth protection di terra LO: < 5 V or open; - HI: 11 to 0 V livelli: LO: LO < = 5 V 5 or V o open; aperto; HI: HI 11 = to V V LPPT NOTE: The sensors can be of any type, the output level must be high when there is material (HI). 81

82 Ricevitore Receiver receiver s0 s s BN (2V) WH BU (0V) BK GY 1 R Sens_2 s R R Sens_ Sens_ pin colore segnale signal type tipo funzione function levels livelli 1 BN 2VV CC DC POWER uscita supply tensione voltage di alimentazione output corrente max. total uscita output totale current: Max.:100 ma 2 WH sens_2 IN ingresso muting sensore 2 di input muting 2 LO: < 5 V or o aperto; open; HI: V BU 0VV CC DC POWER riferimento power supply di alimentazione reference - BK sens_ IN ingresso muting sensore di input muting LO: < 5 V input o aperto; selection HI: V 5 GY PE GND protezione earth protection di terra LO: < 5 V or open; - HI: V livelli: LO: LO < = 5 5 V V or o open; aperto; HI: HI = V V NOTE: the sensors can be of any type, the output level must be high when there is material (HI). dimensions (mm) LPPT/0A-050M2() (passive unit) (active unit) LPPT 82

83 LPPT/0B-080M2() 1,02 50 (passive unit) 60 1, (active unit) 67 LPPT/0C-090M2() 1, (passive unit) 1, (active unit) LPPT 8

84 accessories ST20 / outfit mounting accessories product to be used with dimensions (mm) description / installation stainless steel plate M6 foto LP series 50 0 M ø Fastening insert for 50 x 60 profile. Part of the standard kit Two pieces are provided for each bracket ST ST202 / outfit mounting accessories product to be used with dimensions (mm) description / installation foto LP series L Bracket Long bracket. Part of the standard kit. Two pieces are provided for each couples. Must be applied in the housin part of the body LPPT 8

85 Safety light Curtains Accessories connectors CD12M/0E-***A1 / M12 8 poles axial female connector with PVC cable product to be used with dimensions (mm) description / installation foto Safety light Curtains LS2 STANDARD (TX) LS STANDARD (TX) LPER/0*-***L12 (RX) LPPF Safety Sensors SH e TH SH-IC e TH-IC ø16 max M12x1 8 max L M12 8 poles axial female connector with PVC cable. Cable length is represented by *** digits: 050 : 5 m 100 : 10 m 150 : 15 m 250 : 25 m 00 : 0 m CD12M/0E-***C1 / M12 8 poles 90 female connector with PVC cable product to be used with dimensions (mm) description / installation 9 max L foto Safety light Curtains LS2 STANDARD (RX) LS STANDARD (RX) LPER/0*-***L12 (RX) LPPF max M12x1 ø16 max M12 8 poles 90 female connector with PVC cable. Cable length is represented by *** digits: 050 : 5 m 100 : 10 m 150 : 15 m CD12M/0H-***A / M12 5 poles axial female connector with PVC cable product to be used with dimensions (mm) description / installation Safety light Curtains LS2 BASE (TX e RX) LS2 STANDARD (TX) LS BASE (TX e RX) LS STANDARD (TX) Safety Sensors SH e TH SH-IC e TH-IC ø16 max M12x1 8 max L M12 5 poles axial female connector with PVC cable. Cable length is represented by *** digits: 050 : 5 m 100 : 10 m 150 : 15 m 250 : 25 m 500 : 50 m CD12M/0H-***C / M12 5 poles 90 female connector with PVC cable product to be used with dimensions (mm) description / installation foto Safety light Curtains LS2 BASE (TX e RX) LS2 STANDARD (TX) LS BASE (TX e RX) LS STANDARD (TX) Safety Sensors SH e TH SH-IC e TH-IC max 9 max L M12x1 2 ø16 max 1 5 M12 5 poles 90 female connector with PVC cable. Cable length is represented by *** digits: 050 : 5 m 100 : 10 m 150 : 15 m Accessories Safety 85

86 CD12M/0H-050D1 / M12 5 poles axial female connector product to be used with dimensions (mm) description / installation 9 max L Safety light Curtains foto LPER_M LPPT To be used for Muting 6 max M12x1 ø16 max M12 5 poles axial female connector CDP12/0H-***AC / M12 5 poles axial female female plug product to be used with dimensions (mm) description / installation foto Safety light Curtains LS2_M, LS2_S, LS2_F (MASTER-SLAVE) LS_M, LS_S, LS2_F (MASTER-SLAVE) LPER, LPER_M: connection TX alla LP/ BOX-1 ø16 max M12x1 8 max L 8 max ø16 max M12x1 M12 5 poles axial female female plug. Cable length is represented by *** digits: 00 : 0. m 00 : m 050 : 5 m CD2M/0R-***A1 / M2 19 poles axial connector with PVC cable product to be used with dimensions (mm) description / installation M2 19 poles axial connector with PVC cable. foto Safety light Curtains LPER/0_L LPER_M (RX) LPPT (Unità attiva) M2 ø L Cable length is represented by *** digits: 00 : m 050 : 5 m 100 : 10 m 150 : 15 m 200 : 20 m 00 : 0 m CD2M/0R-***A1LM / M2 19 poles axial connector with PVC cable and external Muting Lamp wire product to be used with dimensions (mm) description / installation foto Safety light Curtains LPER_M; LP_PT; M2 ø L M2 19 poles axial connector with PVC cable and external Muting Lamp wire. Cable length is represented by *** digits: 200 : 20 m 00 : 0 m Accessories Safety 86

87 CDP2/0R-***AC / M2 19 poles axial female female plug product to be used with dimensions (mm) description / installation foto Safety light Curtains LPER/0_L LPER_M (RX) LPPT (active unit) To connect RX or Active Unit to LP/BOX-1 M2 ø L M12 5 poles axial female female plug. Cable length is represented by *** digits: 00 : m 050 : 5 m 100 : 10 m mounting brackets and anti-vibrating bumpers ST VP / pieces anti-vibrating bumpers kit product to be used with dimensions (mm) description / installation M6 foto Safety light Curtains LP 2 20 pieces anti-vibrating bumpers kit for LP Safety light Curtains 6 M6 ST VP 6 / 6 pieces anti-vibrating bumpers kit product to be used with dimensions (mm) description / installation M6 foto Safety light Curtains LP pieces anti-vibrating bumpers kit for LP Safety light Curtains 6 M6 ST V S / pieces anti-vibrating bumpers kit product to be used with dimensions (mm) description / installation M5 foto Safety light Curtains LS2 LS pieces anti-vibrating bumpers kit for LS Safety light Curtains 150 mm protected height models M5 Accessories Safety 87

88 ST 8V S / 8 pieces anti-vibrating bumpers kit product to be used with dimensions (mm) description / installation M5 foto Safety light Curtains LS2 LS pieces anti-vibrating bumpers kit for LS Safety light Curtains ,050 mm protected height models M5 ST 12V S / 12 pieces anti-vibrating bumpers kit for LS Safety light Curtains product to be used with dimensions (mm) description / installation M5 foto Safety light Curtains LS2 LS pieces anti-vibrating bumpers kit for LS Safety light Curtains 1, ,800 mm protected height models M5 ST 201 / pieces L short mounting brackets kit product to be used with dimensions (mm) description / installation 0 foto Safety light Curtains LP pieces L short mounting brackets kit for LP Safety light Curtains 50 ST / 6 pieces L short mounting brackets kit product to be used with dimensions (mm) description / installation 0 foto Safety light Curtains LP pieces L short mounting brackets kit for LP Safety light Curtains 50 Accessories Safety 88

89 ST 202 / pieces L curved mounting brackets for passive element product to be used with dimensions (mm) description / installation foto pieces L curved mounting brackets for passive element of LPPF and LPPT series ST 20 / pieces mounting nuts kit for LP Safety light Curtains product to be used with dimensions (mm) description / installation stainless steel plate M6 foto Safety light Curtains LP 50 0 M ø pieces mounting nuts kit for LP Safety light Curtains 2 ST 20 6 / 6 pieces mounting nuts kit for LP safety light curtains product to be used with dimensions (mm) description / installation stainless steel plate M6 foto Safety light Curtains LP 50 0 ø pieces mounting nuts kit for LP Safety light Curtains M ST 20 S / pieces mounting brackets kit product to be used with dimensions (mm) description / installation foto Safety light Curtains LS2 LS pieces mounting brackets kit for LS2/ LS Safety light Curtains Accessories Safety 89

90 ST 20 6S / 6 pieces mounting brackets kit product to be used with dimensions (mm) description / installation foto Safety light Curtains LS2 LS pieces mounting brackets kit for LS2/ LS Safety light Curtains ST 206 S / pieces L curved mounting brackets kit product to be used with dimensions (mm) description / installation foto Safety light Curtains LS2 LS pieces L curved mounting brackets aad nuts kit for LS2/LS Safety light Curtains to ease mechanical installation ST 206 6S / 6 pieces L curved mounting brackets kit product to be used with dimensions (mm) description / installation foto Safety light Curtains LS2 LS pieces L curved mounting brackets ad nuts kit for LS2/LS Safety light Curtains to ease mechanical installation ST 207 S / pieces rotating brackets kit product to be used with dimensions (mm) description / installation foto Safety light Curtains LS2 LS 1 8 pieces rotating brackets and nuts kit for LS2/LS Safety light Curtains Accessories Safety 90

91 test rod ST 221 / 2220 / 220 / 220 / 2250 product to be used with dimensions (mm) description / installation foto Safety light curtains LSER/1 LSER/20 LS2ER/0 LSER/0 LS2ER/0 LSER/0 LPER/ mm resolution test rod model ST 221 ST 2220 ST 220 ST 220 ST 2250 BLACK painted aluminum pipe Dim. A (mm) Dim. A (mm) ø1 1 ø 20 1 ø 0 1 ø 0 1 ø 50 1,5 protective columns for safety light curtains ST F FIX / standard column base product to be used with dimensions (mm) description / installation 28 foto Columns for Safety series ST CL*** ST CLS*** 202 Standard column base 22 ST FLEX / column base with load springs product to be used with dimensions (mm) description / installation 50 foto Safety light Curtains ST CL*** ST CLS*** 202 Column base with load springs 22 Accessories Safety 91

92 product to be used with dimensions (mm) description / installation ST CL A 2 beams LP Safety light Curtains Column for LP 2 beams light curtain ST CL B beams LP Safety light Curtains L Column for LP beams light curtain ST CL C beams LP Safety light Curtains Column for LP beams light curtain ST CL 17 LP Safety light Curtains h 1,700 mm B Column for h=1,700 mm LP light curtains ST CL 20 LP Safety light Curtains h 2,000 mm Column for h=2,000 mm LP light curtains ST CL AP Safety light Curtains LP 2 beams Column for 2 beams LP light curtains, with PG11 connection ST CL BP Safety light Curtains LP beams 22 Column for beams LP light curtains, with PG11 connection ST CL CP Safety light Curtains LP beams 202 Column for beams LP light Curtains, with PG11 connection ST CL 17P ST CL 17P Safety light Curtains LP h 1,700 mm Safety light Curtains LP h 1,700 mm models QUOTE L [mm] QUOTE B [mm] ST CL A ST CL B ST CL C ST CL 17 ST CL 20 ST CL AP ST CL BP ST CL CP ST CL 17P ST CL 20P 1,000 1,200 1,0 1,700 1, Column for LP light curtains h =1,700 mm, with PG11 connection Column for LP light Curtains h = 2,000 mm, with PG11 connection product to be used with dimensions (mm) description / installation 1, ST AX Safety light Curtains LS2 LS LP 0 Simple Column for LP and LS light curtains 22 Accessories Safety

93 product to be used with dimensions (mm) description / installation Safety light Curtains ST CLS B LS2ER/0A LS ER/0A LS2ER/**- 00(05)(060) LSER/**- 00(05)(060) Column for LS 2 beams light Curtain Safety light Curtains ST CLS C LS2ER/0B(0C) LS ER/0B(0C) LS2ER/**- 075 (090)(105) LSER/**- 075 (090)(105) L Column for LS and beams light Curtain Safety light Curtains ST CLS 17 LS2ER/**- 120 (15) LSER/**- 120 (15) B Column for LS h = 1,700 mm ST CLS 20 Safety light Curtains LS2ER/**-150 LSER/**-150 Column for LS h = 2,000 mm Safety light Curtains ST CLS BP LS2ER/0A LS ER/0A LS2ER/**- 00 (05)(060) LSER/**- 00 (05)(060) 22 Column for LS 2 beams light Curtain, with PG11 connection Safety light Curtains ST CLS CP LS2ER/0B(0C) LS ER/0B(0C) LS2ER/**- 075 (090)(105) LSER/**- 075 (090)(105) 202 Column for LS and beams light Curtain, with PG11 connection ST CLS 17P Safety light Curtains LS2ER/**- 120 (15) LSER/**- 120 (15) Column h=1,700 mm for LS light Curtain, with PG11 connection model ST CLS B ST CLS C ST CLS 17 ST CLS 20 ST CLS BP ST CLS CP ST CLS 17P ST CLS 20P ST CLS 20P Safety light Curtains LS2ER/**- 150 LSER/**- 150 QUOTE L [mm] QUOTE B [mm] with ST FLEX base 1,000 1,0 1,660 1, Column h=2,000 mm for LS light Curtain, with PG11 connection QUOTE B [mm] with ST FIX base Accessories Safety 9

94 deviating mirrors or columns with integrated mirrors product to be used with dimensions (mm) description / installation c SLA CL A B C b profile height and corresponding a mirror height Total SL X CL height (without ST FIX or ST FLEX base) Total SL X CL height with ST FIX base Column with mirrors for 2 beams safety light curtain a D Total SL X CL height with ST FLEX base b E Max ST FLEX height from floor (load springs height) A B C D F Max ST FIX height from floor (blocks height) G Upper plate thickness including level ball SLB CL g f H I L SL X CL base diameter ST FIX or ST FLEX amount of space ST FIX or ST FLEX amount of space Column with mirrors for beams safety light curtain Safety light Curtains LS2 LS LP L H h d e I a b c d Mirror Column housing Vertical level ball Lower fixing plate for ST FLEX base SLC CL e Upper fixing plate for ST FLEX where to mount SL X CL column or ST FIX ground fixing plate Column with mirrors for beams safety light curtain f g Column fixing screws and orientating reference rings ST FLEX inclination adjusting nuts or ST FIX reference plane inclination adjusting double nuts h Floor fixing nuts place SL 17 CL Column with mirrors h = 1,700 mm model QUOTE A (1) QUOTE B (2) QUOTE C () QUOTE D () application SL 20 CL SL A CL 1,000 1,016 1,06 1,066 2 beams perimetral protection Column with mirrors h = 2,000 mm SL B CL 1,200 1,216 1,26 1,256 beams perimetral protection SL C CL 1,0 1,6 1,66 1,86 beams perimetral protection SL 17 CL 1,700 1,716 1,76 1,756 Perimetral protection with height up to 160 mm SL 20 CL 1,970 1,986 2,006 2,026 Perimetral protection with height up to 1660mm Accessories Safety (1) Housing or mirror height (2) Total column height without base () Total height with ST FIX base () Total height with ST FLEX base 9

95 product to be used with dimensions (mm) description / installation SL 015 M8 Mirror for 160 mm protected height SL 00 0 Mirror for 10 mm protected height SL 05 Mirror for 60 mm protected height SL 060 H Mirror for 610 mm protected height SL 075 Mirror for 760 mm protected height SL 090 SL 105 Safety light Curtains LS2 LS LP Mirror for 910 mm protected height Mirror for 1,060 mm protected height SL Mirror for 1,210 mm protected height SL Mirror for 1,60 mm protected height SL Mirror for 1,510 mm protected height SL Ø 9.1 R5 Mirror for 1,660 mm protected height SL Mirror for 1,810 mm protected height mirror Safety light Curtain model SL 015 H protected height type SL 00 SL light Curtain SL 060 SL 075 SL 090 SL 105 SL 120 SL beams light Curtain 1, beams 1,20 1,060 beams 1,00 1,210 1,50 1,60 SL 150 SL 165 SL 180 1,600 1,510 1,750 1,660 1,900 1,810 light Curtain Accessories Safety 95

96 laser pointer STL 01 P product to be used with dimensions (mm) description / installation foto Safety light Curtains LP = = 78 Laser pointer for LP safety light Curtain 70 STL 01 S product to be used with dimensions (mm) description / installation foto Safety light Curtains LS2 LS 117 Laser pointer for LS safety light Curtain 1 80 box d interconnessione LP / BOX - 1 product to be used with dimensions (mm) description / installation foto Safety light Curtains LPER_M LPPT Control box: Start, Override, Muting Lamp, M12 and M2 connectors, 2 NO + 1 NC Relay 180 relay modules / safety modules SB 00 product to be used with dimensions (mm) description / installation Safety light Curtains foto LS2 LS 82 Force guided relay module LP Accessories Safety

97 SB 00 product to be used with dimensions (mm) description / installation Safety light Curtains foto LS2 LS LP 11.5 Cat. Safety Module SB 00M product to be used with dimensions (mm) description / installation 99 5 foto Safety light Curtains LS2 LS 11.5 Cat. Safety Module with integrated Muting function SBCR0 and SH-IA/IC TH-IA/IC accessories series STC 00 product to be used with dimensions (mm) description / installation SW M6 65 foto RL110,116,11G reflectors RL110,116,11G bracket for cylindrical rod STC 18 product to be used with dimensions (mm) description / installation 9 0 Ø 18.5 foto SH-IA/IC, TH-IA/IC safety photocells SH-IA/IC, TH-IA/IC bracket for cylindrical rod Ø 20 Accessories Safety 97