LM135 LM235 - LM335,A
|
|
|
- Morgan Potter
- 5 years ago
- Views:
Transcription
1 LM135 LM235 - LM335,A PRECISION TEMPERATURE SENSORS DIRECTLY CALIBRATED IN K 1 C INITIAL ACCURACY OPERATES FROM 450µA TO 5mA LESS THAN 1Ω DYNAMIC IMPEDANCE DESCRIPTION The LM135, LM235, LM335 are precision temperature sensors which can be easily calibrated. They operate as a 2-terminal Zener and the breakdown voltage is directly proportional to the absolute temperature at 10mV/ K. The circuit has a dynamic impedance of less than 1Ω and operates within a range of current from 450µA to 5mA without alteration of its characteristics. Calibrated at +25 C, the LM135, LM235, LM335 have a typical error of less than 1 C over a 100 C temperature range. Unlike other sensors, the LM135, LM235, LM335 have a linear output. PIN CONNECTIONS (top view) ORDER CODE Part Number Z TO92 (Plastic Package) D SO8 (Plastic Micropackage) Temperature Range Package LM C, +150 C LM C, +125 C LM335,A -40 C, +100 C Z = TO92 Plastic package - also available in Bulk (Z), Tape & Reel (ZT) and Ammo Pack (AP)e D = Small Outline Package (SO) - also available in Tape & Reel (DT) Z D TO92 (Top view) SO8 (Top view) ADJ v+ v- May /12
2 SCHEMATIC DIAGRAM ABSOLUTE MAXIMUM RATINGS Symbol Parameter LM135 LM235 LM335,A Unit I R I F Current Reverse Forward Toper Operating Free-air Temperature Range 1) Continuous Intermittent -55 to to to to to to +125 T Stg Storage Temperature Range -65 to +150 C 1. Tj 150 C ma C 2/12
3 TEMPERATURE ACCURACY LM135 - LM235 - LM335A LM335 Parameter Unit Min. Typ. Max. Min. Typ. Max. Operating Output Voltage T case = +25 C, I R = 1mA V Uncalibrated Temperature Error (I R = 1mA) T case = +25 C C T min. T case T max Temperature Error with 25 C Calibration T min. T case T max., I R = 1mA LM135 - LM C LM LM335A Calibrated Error at Extended Temperature T case = T max. (intermittent) 2 2 C Non-linearity (I R = 1mA) LM135 - LM C LM LM335A ELECTRICAL CHARACTERISTICS - (note 1) LM135 - LM235 LM335,A Parameter Unit Min. Typ. Max. Min. Typ. Max. Operating output voltage change with current 450µA I R 5mA at constant temperature mv Dynamic Impedance (I R = 1mA) Ω Output Voltage Temperature Drift mv/ C Time Constant Still Air Air 0.5m/s Stirred Oil s Time Stability (T case = +125 C) C/kh 1. Accuracy measurements are made in a well-stirred oil bath. For other conditions, self heating must be considered 3/12
4 4/12
5 5/12
6 APPLICATION HINTS There is an easy method of calibrating the device for higher accuracies (see typical applications). The single point calibration works because the output of the LM135, LM235, LM335 is proportional to the absolute temperature with the extrapolated output of sensor going to 0V at 0 K ( C). Errors in output voltage versus temperature are only slope. Thus a calibration of the slope at one temperature corrects errors at all temperatures. The circuit output (calibrated or not) can be given by the equation: V OT + VO TO x T To where T is the unknown temperature and To is the reference temperature (in K). Nominally the output is calibrated at 10mV/ K. Precautions should be taken to ensure good sensing accuracy. As in the case of all temperatures sensors, self heating can decrease accuracy. The LM135, LM235, LM335 should operate with a low current but sufficient to drive the sensor and its calibration circuit to their maximum operating temperature. If the sensor is used in surroundings where the thermal resistance is constant, the errors due to self heating can be externally calibrated. This is possible if the circuit is biased with a temperature stable current. Heating will then be proportional to zener voltage and therefore temperature. In this way the error due to self heating is proportional to the absolute temperature as scale factor errors. 6/12
7 7/12
8 8/12
9 9/12
10 PACKAGE MECHANICAL DATA SO-8 MECHANICAL DATA DIM. mm. inch MIN. TYP MAX. MIN. TYP. MAX. A A A B C D E e H h L k 8 (max.) ddd /C 10/12
11 PACKAGE MECHANICAL DATA - TO92 TAPE AMMO PACK & TO92 TAPE & REEL TO-92 MECHANICAL DATA DIM. mm. inches MIN. TYP MAX. MIN. TYP. MAX. AL A T d I P PO P F1/F h P W W W W H H H DO L Packing information are available at: 11/12
12 PACKAGE MECHANICAL DATA - TO92 BULK TO-92 MECHANICA DATA DIM. mm. mils MIN. TYP MAX. MIN. TYP. MAX. A b D E e e L R S W /C Packing information are available at: Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 12/ STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom
LM134 LM234 - LM334 THREE TERMINAL ADJUSTABLE CURRENT SOURCES
LM134 LM234 - LM334 THREE TERMINAL ADJUSTABLE CURRENT SOURCES OPERATES FROM 1V TO 40V 0.02%/V CURRENT REGULATION PROGRAMMABLE FROM 1µA TO 10mA ±3% INITIAL ACCURACY DESCRIPTION The LM134/LM234/LM334 are
LM217L LM317L LOW CURRENT 1.2 TO 37V ADJUSTABLE VOLTAGE REGULATOR
LM217L LM317L LOW CURRENT 1.2 TO 37V ADJUSTABLE VOLTAGE REGULATOR OUTPUT VOLTAGE RANGE: 1.2 TO 37V OUTPUT CURRENT IN EXCESS OF 100 ma LINE REGULATION TYP. 0.01% LOAD REGULATION TYP. 0.1% THERMAL OVERLOAD
NE556 SA556 - SE556 GENERAL PURPOSE DUAL BIPOLAR TIMERS
NE556 SA556 - SE556 GENERAL PURPOSE DUAL BIPOLAR TIMERS LOW TURN OFF TIME MAXIMUM OPERATING FREQUENCY GREATER THAN 500kHz TIMING FROM MICROSECONDS TO HOURS OPERATES IN BOTH ASTABLE AND MONOSTABLE MODES
TS V MICROPOWER SHUNT VOLTAGE REFERENCE 2.5V OUTPUT VOLTAGE ULTRA LOW CURRENT CONSUMPTION:
2.5V MICROPOWER SHUNT VOLTAGE REFERENCE 2.5V OUTPUT VOLTAGE ULTRA LOW CURRENT CONSUMPTION: 4µA TYP. HIGH PRECISION @ 25 C ±2% and ±1% HIGH STABILITY WHEN USED WITH CAPACITIVE LOAD INDUSTRIAL TEMPERATURE
UA748 PRECISION SINGLE OPERATIONAL AMPLIFIER
PRECISION SINGLE OPERATIONAL AMPLIFIER INPUT OFFSET VOLTAGE : 3mV max. OVER TEMPERATURE FREQUENCY COMPENSATION WITH A SINGLE 30pF CAPACITOR (C1) OPERATION FROM ±5V to ±15V LOW POWER CONSUMPTION : 50mW
LM101A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS
LM1A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS LM1A LM201A LM301A INPUT OFFSET VOLTAGE 0.7mV 2mV INPUT BIAS CURRENT 25nA 70nA INPUT OFFSET CURRENT 1.5nA 2nA SLEW RATE AS INVERSINGV/µs V/µs AMPLIFIER
TS834 MICROPOWER VOLTAGE SUPERVISOR RESET ACTIVE LOW OR HIGH INTEGRATED TIMER
MICROPOWER VOLTAGE SUPERVISOR RESET ACTIVE LOW OR HIGH INTEGRATED TIMER ULTRA LOW POWER CONSUMPTION : 12µA max. @ V CC = 5V BOTH ACTIVE HIGH AND ACTIVE LOW OUTPUTS RESET TIMER WITH DISABLE FUNCTION PRECISION
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM150/LM250 LM350 THREE-TERMINAL 3 A ADJUSTABLE VOLTAGE REGULATORS GUARANTEED
TDA7231A 1.6W AUDIO AMPLIFIER OPERATING VOLTAGE 1.8 TO 15 V LOW QUIESCENT CURRENT HIGH POWER CAPABILITY LOW CROSSOVER DISTORTION SOFT CLIPPING
1.6 AUDIO AMPLIFIER OPERATING VOLTAGE 1.8 TO 15 V LO QUIESCENT CURRENT. HIGH POER CAPABILITY LO CROSSOVER DISTORTION SOFT CLIPPING DESCRIPTION The is a monolithic integrated circuit in 4 + 4 lead minidip
TSM100 SINGLE OPERATIONAL AMPLIFIER AND SINGLE COMPARATOR
OPERATIONAL AMPLIFIER LOW INPUT OFFSET VOLTAGE : 0.5 typ. MEDIUM BANDWIDTH (unity gain) : 0.9MHz LARGE OUTPUT VOLTAGE SWING : 0V to (V CC - 1.5V) INPUT COMMON MODE VOLTAGE RANGE INCLUDES GROUND WIDE POWER
TS HIGH THERMAL STABILITY MICROPOWER SHUNT VOLTAGE REFERENCE
HIGH THERMAL STABILITY MICROPOWER SHUNT VOLTAGE REFERENCE LOW Tc: ppm/ C MAXIMUM.V OUTPUT VOLTAGE LOW OPERATING CURRENT: 6µA max @ C HIGH PRECISION AT C: ±.% AND ±% STABLE WHEN USED WITH CAPACITIVE LOADS
TEB1033 TEF1033-TEC1033
TEB1033 TEF1033-TEC1033 PRECISION DUAL OPERATIONAL AMPLIFIERS VERY LOW INPUT OFFSET VOLTAGE : 1mV max. LOW DISTORTION RATIO LOW NOISE VERY LOW SUPPLY CURRENT LOW INPUT OFFSET CURRENT LARGE COMMON-MODE
Obsolete Product(s) - Obsolete Product(s)
BYT 30P-1000 FAST RECOVERY RECTIFIER DIODE VERY HIGH REVERSE VOLTAGE CAPABILITY VERY LOW REVERSE RECOVERY TIME VERY LOW SWITCHING LOSSES LOW NOISE TURN-OFF SWITCHING SUITABLE APPLICATIONS FREE WHEELING
74V1T07CTR SINGLE BUFFER (OPEN DRAIN)
SINGLE BUFFER (OPEN DRAIN) HIGH SPEED: t PD = 4.3ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN), V IL = 0.8V (MAX) POWER DOWN PROTECTION
BZW06-5V8/376 BZW06-5V8B/376B
BZW06-5V8/376 BZW06-5V8B/376B TRANSIL TM FEATURES PEAK PULSE POWER : 600 W (10/1000µs) STAND-OFF VOLTAGE RANGE : From 5.8V to 376 V UNI AND BIDIRECTIONAL TYPES LOW CLAMPING FACTOR FAST RESPONSE TIME UL
Symbol Parameter Value Unit. Maximum lead temperature for soldering during 10s at 5mm from case
BZW50-10,B/180,B TRANSIL TM FEATURES PEAK PULSE POWER : 5000 W (10/1000µs) STAND-OFF VOLTAGE RANGE : From 10V to 180V UNI AND BIDIRECTIONAL TYPES LOW CLAMPING FACTOR FAST RESPONSE TIME UL RECOGNIZED DESCRIPTION
LF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER
LF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER INTERNALLY ADJUSTABLE INPUT OFFSET VOLTAGE LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW
LM723 HIGH PRECISION VOLTAGE REGULATOR
HIGH PRECISION VOLTAGE REGULATOR INPUT VOLTAGE UP TO 40V OUTPUT VOLTAGE ADJUSTABLE FROM 2 TO 37V POSITIVE OR NEGATIVE SUPPLY OPERATION SERIES, SHUNT, SWITCHING OR FLOATING OPERATION OUTPUT CURRENT TO 150mA
Distributed by: www.jameco.com -800-8- The content and copyrights of the attached material are the property of its owner. NE SA - SE GENERAL PURPOSE SINGLE BIPOLAR TIMERS LOW TURN OFF TIME MAXIMUM OPERATING
L4940 SERIES VERY LOW DROP 1.5A REGULATORS
L4940 SERIES VERY LOW DROP 1.5A REGULATORS PRECISE 5, 8.5, 10, 12V OUTPUTS LOW DROPOUT VOLTAGE (500mV Typ. at 1.5A) VERY LOW QUIESCENT CURRENT THERMAL SHUTDOWN SHORT CIRCUIT PROTECTION REVERSE POLARITY
TDA0161. Proximity Detectors. Features. Description. Block Diagram. 10mA Output Current Oscillator Frequency 10MHz Supply Voltage +4 to +35V
Proximity Detectors Features 10mA Output Current Oscillator Frequency 10MHz Supply Voltage +4 to +35V Description These monolithic integrated circuits are designed for metallic body detection by sensing
LM158,A-LM258,A LM358,A
,A-LM258,A LM358,A LOW POWER DUAL OPERATIONAL AMPLIFIERS INTERNALLY FREQUENCY COMPENSATED LARGE DC VOLTAGE GAIN: 1dB WIDE BANDWIDTH (unity gain): 1.1MHz (temperature compensated) VERY LOW SUPPLY CURRENT/OP
L4941 VERY LOW DROP 1A REGULATOR
VERY LOW DROP 1A REGULATOR LOW DROPOUT VOLTAGE (450mV Typ. at 1A) VERY LOW QUIESCENT CURRENT THERMAL SHUTDOWN SHORT CIRCUIT PROTECTION REVERSE POLARITY PROTECTION DESCRIPTION The L4941 is a three terminal
Obsolete Product(s) - Obsolete Product(s)
SINGLE 2-INPUT NOR GATE HIGH SPEED: t PD = 3.6ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS
ESDA6V1U1 TRANSIL ARRAY FOR ESD PROTECTION. Application Specific Discretes A.S.D.
Application Specific Discretes A.S.D. ESDA6V1U1 TRANSIL ARRAY FOR ESD PROTECTION APPLICATIONS Where transient overvoltage protection in ESD sensitive equipment is required, such as : COMPUTERS PRINTERS
74V1T126CTR SINGLE BUS BUFFER (3-STATE)
SINGLE BUS BUFFER (3-STATE) HIGH SPEED: t PD = 3.6ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN), V IL = 0.8V (MAX) POWER DOWN
Obsolete Product(s) - Obsolete Product(s)
SINGLE INVERTER (OPEN DRAIN) HIGH SPEED: t PD = 3.7ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
74V1G00CTR SINGLE 2-INPUT NAND GATE
SINGLE 2-INPUT NAND GATE HIGH SPEED: t PD = 3.7ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS
LM138/LM238 LM338 THREE-TERMINAL 5 A ADJUSTABLE VOLTAGE REGULATORS
LM138/LM238 LM338 THREE-TERMINAL 5 A ADJUSTABLE VOLTAGE REGULATORS GUARANTEED 7A PEAK OUTPUT CURRENT GUARANTEED 5A OUTPUT CURRENT ADJUSTABLE OUTPUT DOWN TO 1.2V LINE REGULATION TYPICALLY 0.005%/V LOAD
UA741 GENERAL PURPOSE SINGLE OPERATIONAL AMPLIFIER
GENERAL PURPOSE SINGLE OPERATIONAL AMPLIFIER LARGE INPUT VOLTAGE RANGE NO LATCH-UP HIGH GAIN SHORT-CIRCUIT PROTECTION NO FREQUENCY COMPENSATION REQUIRED SAME PIN CONFIGURATION AS THE UA709 N DIP8 (Plastic
LF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS
LF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT
Obsolete Product(s) - Obsolete Product(s)
TRIPLE 3-INPUT NOR GATE HIGH SPEED: t PD = 4.1 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
Obsolete Product(s) - Obsolete Product(s)
P-CHANNEL 20V - 0.065Ω - 5ASOT23-6L 2.5V-DRIVE STripFET II POWER MOSFET TYPE V DSS R DS(on) I D STT5PF20V 20 V < 0.080 Ω (@4.5V)
74V1T00CTR SINGLE 2-INPUT NAND GATE
SINGLE 2-INPUT NAND GATE HIGH SPEED: t PD = 5.0ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH =2V(MIN),V IL =0.8V(MAX) POWER DOWN PROTECTION
Obsolete Product(s) - Obsolete Product(s)
SINGLE 2-INPUT NAND GATE HIGH SPEED: t PD = 5.0ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH =2V(MIN),V IL =0.8V(MAX) POWER DOWN PROTECTION
LDRxxyy VERY LOW DROP DUAL VOLTAGE REGULATOR
VERY LOW DROP DUAL VOLTAGE REGULATOR OUTPUT CURRENT 1 UP TO 500mA OUTPUT CURRENT 2 UP TO 1.0A LOW DROPOUT VOLTAGE 1 (0.3V @ I O =500mA) LOW DROPOUT VOLTAGE 2 (0.4V @ I O =1A) VERY LOW SUPPLY CURRENT (TYP.50µA
MJD122-1 / MJD122T4 MJD127-1 / MJD127T4 COMPLEMENTARY POWER DARLINGTON TRANSISTORS
MJD122-1 / MJD122T4 MJD127-1 / MJD127T4 COMPLEMENTARY POWER DARLINGTON TRANSISTORS Ordering Code Marking Package Shipment MJD122T4 MJD122-1 MJD127T4 MJD127-1 MJD122 MJD122 MJD127 MJD127 TO-252 (DPAK) TO-251
Obsolete Product(s) - Obsolete Product(s)
OPERATIONAL AMPLIFIERS LOW SUPPLY CURRENT : 375µA/op. (@ V CC = 5V) LOW INPUT BIAS CURRENT : 2nA MEDIUM SPEED :.9MHz LOW INPUT OFFSET VOLTAGE :.5mV typ for TSM14A WIDE POWER SUPPLY RANGE : ±1.5V to ±15V
TDA7241B 20W BRIDGE AMPLIFIER FOR CAR RADIO
TDA7241B 20W BRIDGE AMPLIFIER FOR CAR RADIO VERY LOW STAND-BY CURRENT GAIN = 32dB OUTPUT PROTECTED AGAINST SHORT CIRCUITS TO GROUND AND ACROSS LOAD COMPACT HEPTAWATT PACKAGE DUMP TRANSIENT THERMAL SHUTDOWN
74VHC20 DUAL 4-INPUT NAND GATE
DUAL 4-INPUT NAND GATE HIGH SPEED: t PD = 3.3 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
Obsolete Product(s) - Obsolete Product(s)
PN2222A ABSOLUTE MAXIMUM RATINGS SMALL SIGNAL NPN TRANSISTOR PRELIMINARY DATA Ordering Code Marking Package / Shipment PN2222A PN2222A TO-92 / Bulk PN2222A-AP PN2222A TO-92 / Ammopack SILICON EPITAXIAL
TL061 TL061A - TL061B
TL61 TL61A - TL61B LOW POWER J-FET SINGLE OPERATIONAL AMPLIFIERS VERY LOW POWER CONSUMPTION : µa WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT
STD10NF10 N-CHANNEL 100V Ω - 13A IPAK/DPAK LOW GATE CHARGE STripFET II POWER MOSFET
N-CHANNEL 100V - 0.115 Ω - 13A IPAK/DPAK LOW GATE CHARGE STripFET II POWER MOSFET TYPE V DSS R DS(on) I D STD10NF10 100 V
TSM104W/A QUAD OPERATIONAL AMPLIFIER AND PROGRAMMABLE VOLTAGE REFERENCE OPERATIONAL AMPLIFIERS
TSM14W/A QUAD OPERATIONAL AMPLIFIER AND PROGRAMMABLE VOLTAGE REFERENCE OPERATIONAL AMPLIFIERS LOW SUPPLY CURRENT : 375µA/op. (@ V CC = 5V) LOW INPUT BIAS CURRENT : 2nA MEDIUM SPEED :.9MHz LOW INPUT OFFSET
Obsolete Product(s) - Obsolete Product(s)
SINGLE 2-INPUT NAND GATE 5V TOLERANT INPUTS HIGH SPEED: t PD = 4.7ns (MAX.) at V CC =3V LOW POWER DISSIPATION: I CC =1µA (MAX.)atT A =25 C POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT
TDA W AUDIO AMPLIFIER
TDA2006 12W AUDIO AMPLIFIER DESCRIPTION The TDA2006 is a monolithic integrated circuit in Pentawatt package, intended for use as a low frequency class "AB" amplifier. At ±12V, d = 10 % typically it provides
HCF4070B QUAD EXCLUSIVE OR GATE
QUAD EXCLUSIVE OR GATE MEDIUM-SPEED OPERATION t PHL =t PLH = 70ns (Typ.) at CL = 50 pf and V DD = 10V QUIESCENT CURRENT SPECIFIED UP TO 20V 5V, 10V AND 15V PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I
HCF4050B HEX BUFFER/CONVERTER (NON INVERTING)
HEX BUFFER/CONVERTER (NON INVERTING) PROPAGATION DELAY TIME : t PD = 40ns (TYP.) at V DD = 10V C L = 50pF HIGH TO LOW LEVEL LOGIC CONVERSION HIGH "SINK" AND "SOURCE" CURRENT CAPABILITY QUIESCENT CURRENT
ST755 ADJUSTABLE INVERTING NEGATIVE OUTPUT CURRENT MODE PWM REGULATORS
ADJUSTABLE INVERTING NEGATIVE OUTPUT CURRENT MODE PWM REGULATORS 2.7V TO 11V INPUT TO ADJUSTABLE NEGATIVE OUTPUT CONVERSION 1W GUARANTEED OUTPUT POWER (V I >4.5V,T 70 C) 68% TYP. EFFICENCY AT 6V VERY LOW
STD12NF06L N-CHANNEL 60V Ω - 12A IPAK/DPAK STripFET II POWER MOSFET
N-CHANNEL 60V - 0.08 Ω - 12A IPAK/DPAK STripFET II POWER MOSFET TYPE V DSS R DS(on) I D 60 V < 0.1 Ω 12 A TYPICAL R DS (on) = 0.08 Ω EXCEPTIONAL dv/dt CAPABILITY LOW GATE CHARGE LOW THRESHOLD DRIVE THROUGH-HOLE
Obsolete Product(s) - Obsolete Product(s)
SINGLE SCHMITT INERTER HIGH SPEED: t PD = 4.3ns (TYP.) at CC =5 LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C TYPICAL HYSTERESIS: h =1 at CC =4.5 POWER DOWN PROTECTION ON INPUT SYMMETRICAL OUTPUT
L7900 SERIES NEGATIVE VOLTAGE REGULATORS
L7900 SERIES NEGATIVE VOLTAGE REGULATORS OUTPUT CURRENT UP TO 1.5 A OUTPUT VOLTAGES OF -5; -5.2; -6; -8; -9; -12; -15; -18; -20; -22; -24V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT PROTECTION OUTPUT TRANSITION
74LX1G132CTR SINGLE 2-INPUT SCHMITT NAND GATE
SINGLE 2-INPUT SCHMITT NAND GATE 5V TOLERANT INPUTS HIGH SPEED: t PD = 5.5ns (MAX.) at V CC =3V LOW POWER DISSIPATION: I CC =1µA (MAX.)atT A =25 C TYPICAL HYSTERESIS: V h =1V at V CC =4.5V POWER DOWN PROTECTION
Inverting Input 1. Non-inverting Input 1
Micropower Dual CMOS Voltage Comparators Extremely low supply current: 9µa typ/comp. Wide single supply range 2.7V to 6V or dual supplies (±.35V to ±8V) Extremely low input bias current: pa typ. Extremely
Obsolete Product(s) - Obsolete Product(s)
MMBT2222A APPLICATIONS WELL SUITABLE FOR PORTABLE EQUIPMENT SMALL LOAD SWITCH TRANSISTOR WITH HIGH GAIN AND LOW SATURATION OLTAGE SMALL SIGNAL NPN TRANSISTOR PRELIMINARY DATA Type Marking MMBT2222A M22
-55 to 175 C T j ( ) Pulse width limited by safe operating area.
N-CHANNEL 60V - 0.020 Ω - 28A IPAK/DPAK STripFET II POWER MOSFET TYPE V DSS R DS(on) I D 60 V
L4940 series VERY LOW DROP 1.5 A REGULATORS
L4940 series VERY LOW DROP 1.5 A REGULATORS PRECISE 5 V, 8.5 V, 10 V, 12 V OUTPUTS LOW DROPOUT VOLTAGE (500 typ at 1.5A) VERY LOW QUIESCENT CURRENT THERMAL SHUTDOWN SHORT CIRCUIT PROTECTION REVERSE POLARITY
TSM103/A DUAL OPERATIONAL AMPLIFIER AND VOLTAGE REFERENCE
TSM13/A DUAL OPERATIONAL AMPLIFIER AND VOLTAGE REFERENCE OPERATIONAL AMPLIFIER LOW INPUT OFFSET VOLTAGE :.5 typ.for TSM13A LOW SUPPLY CURRENT : 35µA/op. (@ V CC = 5V) MEDIUM BANDWIDTH (unity gain) :.9MHz
STP55NF03L STB55NF03L STB55NF03L-1 N-CHANNEL 30V Ω - 55A TO-220/D 2 PAK/I 2 PAK STripFET II POWER MOSFET
STP55NF03L STB55NF03L STB55NF03L-1 N-CHANNEL 30V - 0.01 Ω - 55A TO-220/D 2 PAK/I 2 PAK STripFET II POWER MOSFET TYPE V DSS R DS(on) I D STP55NF03L STB55NF03L STB55NF03L-1 30 V 30 V 30 V
Obsolete Product(s) - Obsolete Product(s)
L4904A DUAL 5V REGULATOR WITH RESET OUTPUT CURRENTS : I01 = 50mA I02 = 100mA FIXED PRECISION OUTPUT VOLTAGE 5V ± 2 % RESET FUNCTION CONTROLLED BY INPUT VOLTAGE AND OUTPUT 1 VOLTAGE RESET FUNCTION EXTERNALLY
74VHC08 QUAD 2-INPUT AND GATE
QUAD 2-INPUT AND GATE HIGH SPEED: t PD = 4.3 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
TL081 TL081A - TL081B
TL081 TL081A - TL081B GENERAL PURPOSE J-FET SINGLE OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION
. HIGH PERFORMANCE CLAMPING AT
L9700 HEX PRECISION LIMITER. HIGH PERFORMANCE CLAMPING AT GROUND AND POSITIVE REFERENCE VOLTAGE FAST ACTIVE CLAMPING OPERATING RANGE 4.75-5.25 V SINGLE VOLTAGE FOR SUPPLY AND POSITI-. VE REFERENCE LOW
Obsolete Product(s) - Obsolete Product(s)
QUAD 2-INPUT AND GATE HIGH SPEED: t PD = 4.7 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN.), V IL = 0.8V (MAX) POWER DOWN PROTECTION
Value Unit I T(RMS) RMS on-state current A A Tj = 25 C I FSM current (Tj initial = 25 C)
MAIN FEATURES: DIODE / SCR MODULE Symbol Value Unit I T(RMS) 50-70-85 A V DRM /V RRM 800 and 1200 V I GT 50 and 100 ma DESCRIPTION Packaged in ISOTOP modules, the MDS Series is based on the half-bridge
74V1G77CTR SINGLE D-TYPE LATCH
SINGLE D-TYPE LATCH HIGH SPEED: t PD = 4.4ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS SYMMETRICAL
Obsolete Product(s) - Obsolete Product(s)
HEX INVERTER (OPEN DRAIN) HIGH SPEED: t PD = 10ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) WIDE OPERATING VOLTAGE RANGE:
M74HC51TTR DUAL 2 WIDE 2 INPUT AND/OR INVERT GATE
DUAL 2 WIDE 2 INPUT AND/OR INVERT GATE HIGH SPEED: t PD = 11ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL
STD20NF06L N-CHANNEL 60V Ω - 24A DPAK/IPAK STripFET II POWER MOSFET
Table 1: General Features N-CHANNEL 60V - 0.032 Ω - 24A DPAK/IPAK STripFET II POWER MOSFET Figure 1:Package TYPE V DSS R DS(on) I D -1 60 V 60 V TYPICAL R DS (on) = 0.032 Ω < 0.040 Ω < 0.040 Ω EXCEPTIONAL
74VHCT00ATTR QUAD 2-INPUT NAND GATE
QUAD 2-INPUT NAND GATE HIGH SPEED: t PD = 5 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN.), V IL = 0.8V (MAX) POWER DOWN PROTECTION
M74HC10TTR TRIPLE 3-INPUT NAND GATE
TRIPLE 3-INPUT NAND GATE HIGH SPEED: t PD = 8ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
STS7PF30L P-CHANNEL 30V Ω - 7ASO-8 STripFET II POWER MOSFET
TYPE V DSS R DS(on) I D STS7PF30L P-CHANNEL 30V - 0.016Ω - 7ASO-8 STripFET II POWER MOSFET PRELIMINARY DATA STS7PF30L 30 V < 0.021 Ω 7A TYPICAL R DS (on) = 0.016Ω STANDARD OUTLINE FOR EASY AUTOMATED SURFACE
Obsolete Product(s) - Obsolete Product(s)
QUAD 2-INPUT NAND GATE HIGH SPEED: t PD = 8ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
L165 3A POWER OPERATIONAL AMPLIFIER
3A POWER OPERATIONAL AMPLIFIER OUTPUT CURRENT UP TO 3A LARGE COMMON-MODE AND DIFFERENTIAL MODE RANGES SOA PROTECTION THERMAL PROTECTION ± 18V SUPPLY DESCRIPTION The L165 is a monolithic integrated circuit
Obsolete Product(s) - Obsolete Product(s)
QUAD 2 INPUT NAND GATE PROPAGATION DELAY TIME t PD = 60ns (Typ.) at V DD = 10V BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20V 5V, 10V
Obsolete Product(s) - Obsolete Product(s)
HEX INVERTER (SINGLE STATE) HIGH SPEED: t PD = 5ns (TYP.) at V CC = 6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 10% V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
MMBT2222A SMALL SIGNAL NPN TRANSISTOR
SMALL SIGNAL NPN TRANSISTOR PRELIMINARY DATA Type Marking M22 SILICON EPITAXIAL PLANAR NPN TRANSISTOR MINIATURE SOT-23 PLASTIC PACKAGE FOR SURFACE MOUNTING CIRCUITS TAPE & REEL PACKING THE PNP COMPLEMENTARY
PB137 POSITIVE VOLTAGE REGUALTOR FOR BATTERY CHARGER REVERSE LEAKAGE CURRENT LESS THAN
PB137 POSITIVE VOLTAGE REGUALTOR FOR BATTERY CHARGER REVERSE LEAKAGE CURRENT LESS THAN 10 µa THREE TERMINAL FIXED VERSION (13.7V) OUTPUT CURRENT IN EXCESS OF 1.5A AVAILABLEIN ± 1% (AC) SELECTION AT 25
TL062 TL062A - TL062B
TL62 TL62A TL62B LOW POWER JFET DUAL OPERATIONAL AMPLIFIERS VERY LOW POWER CONSUMPTION : µa WIDE COMMONMODE (UP TO + ) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT SHORTCIRCUIT
STX93003 HIGH VOLTAGE FAST-SWITCHING PNP POWER TRANSISTOR
STX93003 HIGH VOLTAGE FAST-SWITCHING PNP POWER TRANSISTOR ST93003 SILICON IN TO-92 PACKAGE MEDIUM VOLTAGE CAPABILITY LOW SPREAD OF DYNAMIC PARAMETERS MINIMUM LOT-TO-LOT SPREAD FOR RELIABLE OPERATION VERY
TDA1151 MOTOR SPEED REGULATOR
MOTOR SPEED REGULATOR EXCELLENT VERSATILITY IN USE HIGH OUTPUT CURRENT (UP TO 800mA) LOW QUIESCENT CURRENT (1.7mA) LOW REFERENCE VOLTAGE (1.2V) EXCELLENT PARAMETERS STABILITY VERSUS TEMPERATURE DESCRIPTION
BUH515 HIGH VOLTAGE FAST-SWITCHING NPN POWER TRANSISTOR HIGH VOLTAGE CAPABILITY U.L. RECOGNISED ISOWATT218 PACKAGE (U.L. FILE # E81734 (N)).
BUH515 HIGH VOLTAGE FAST-SWITCHING NPN POWER TRANSISTOR HIGH VOLTAGE CAPABILITY U.L. RECOGNISED ISOWATT218 PACKAGE (U.L. FILE # E81734 (N)). APPLICATIONS: HORIZONTAL DEFLECTION FOR COLOUR TV AND MONITORS
M74HCT02TTR QUAD 2-INPUT NOR GATE
QUAD 2-INPUT NOR GATE HIGH SPEED: t PD = 15 ns (TYP.) at V CC = 4.5V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS : V IH = 2V (MIN.) V IL = 0.8V (MAX) BALANCED PROPAGATION
74V1G79CTR SINGLE POSITIVE EDGE TRIGGERED D-TYPE FLIP-FLOP
SINGLE POSITIVE EDGE TRIGGERED D-TYPE FLIP-FLOP HIGH SPEED: f MAX = 180MHz (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER
ADJUSTABLE VOLTAGE AND CURRENT REGULATOR
ADJUSTABLE VOLTAGE AND CURRENT REGULATOR ADJUSTABLE OUTPUT CURRENT UP TO 2 A (GUARANTEED UP TO T j = 150 C) ADJUSTABLE OUTPUT VOLTAGE DOWN TO 2.85 V INPUT OVERVOLTAGE PROTECTION (UP TO 60 V, 10 ms) SHORT
STG719 LOW VOLTAGE 4Ω SPDT SWITCH
LOW VOLTAGE 4Ω SPDT SWITCH HIGH SPEED: t PD = 0.3ns (TYP.) at V CC = 5V t PD = 0.4ns (TYP.) at V CC = 3.3V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C LOW "ON" RESISTANCE: R ON = 4Ω (MAX. T A
STD5NM50 STD5NM50-1 N-CHANNEL 500V - 0.7Ω - 7.5A DPAK/IPAK MDmesh Power MOSFET
STD5NM50 STD5NM50-1 N-CHANNEL 500V - 0.7Ω - 7.5A DPAK/IPAK MDmesh Power MOSFET TYPE V DSS R DS(on) I D STD5NM50 STD5NM50-1 500V 500V
Obsolete Product(s) - Obsolete Product(s)
SINGLE BUS BUFFER (3-STATE) HIGH SPEED: t PD = 3.8ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA (MAX.)atT A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS
DIP14 Tube LM2901N LM2901D/LM2901DT SO-14 Tube or Tape & Reel
LM2901 Low Power Quad Voltage Comparator Wide single supply voltage range or dual supplies for all devices: +2V to +36V or ±1V to ±18V Very low supply current (1.1mA) independent of supply voltage (1.4mW/comparator
MC1488 RS-232C QUAD LINE DRIVER
RS-232C QUAD LINE DRIVER CURRENT LIMITED OUTPUT ±10mA TYP. POWER-OFF SOURCE IMPEDANCE 300Ω MIN. SIMPLE SLEW RATE CONTROL WITH EXTERNAL CAPACITOR FLEXIBLE OPERATING SUPPLY RANGE INPUTS ARE TTL AND µp COMPATIBLE
HCF4072B DUAL 4 INPUT OR GATE
DUAL 4 INPUT OR GATE MEDIUM SPEED OPERATION : t PD = 60ns (TYP.) at DD = 10 QUIESCENT CURRENT SPECIFIED UP TO 20 5, 10 AND 15 PARAMETRIC RATINGS INPUT LEAKAGE CURRENT I I = 100nA (MAX) AT DD = 18 T A =
STS7PF30L P-CHANNEL 30V Ω - 7A - SO-8 STripFET II Power MOSFET General features Description Internal schematic diagram
P-CHANNEL 30V - 0.16Ω - 7A - SO-8 STripFET II Power MOSFET General features Type V DSS R DS(on) I D STS7PF30L 30V
L4620 LIQUID LEVEL ALARM. DRIVES DIRECTLY 300 ma ALARM LOAD PROGRAMMABLE INPUT POLARITY TO ACTIVATE THE OUTPUT STAGE PROGRAMMABLE DELAY TIME
L4620 LIQUID LEVEL ALARM DRIVES DIRECTLY 300 ma ALARM LOAD PROGRAMMABLE INPUT POLARITY TO ACTIVATE THE OUTPUT STAGE PROGRAMMABLE DELAY TIME. PROGRAMMABLE OUTPUT DUTY CYCLE OUTPUT SHORT CIRCUIT PROTECTION
74LVX05 LOW VOLTAGE CMOS HEX INVERTER (OPEN DRAIN) WITH 5V TOLERANT INPUTS
LOW VOLTAGE CMOS HEX INVERTER (OPEN DRAIN) WITH 5V TOLERANT INPUTS HIGH SPEED: t PD = 4.8ns (TYP.) at V CC = 3.3V 5V TOLERANT INPUTS INPUT VOLTAGE LEVEL: V IL =0.8V, V IH =2V at V CC =3V LOW POWER DISSIPATION:
Obsolete Product(s) - Obsolete Product(s)
QUAD 2-INPUT NAND GATE HIGH SPEED: t PD = 12ns (TYP.) at V CC = 4.5V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS : V IH = 2V (MIN.) V IL = 0.8V (MAX) BALANCED PROPAGATION
HCF4010B HEX BUFFER/CONVERTER (NON INVERTING)
HEX BUFFER/CONVERTER (NON INVERTING) PROPAGATION DELAY TIME t PD = 40ns (TYP.) at V DD = 10V C L = 50pF HIGH TO LOW LEVEL LOGIC CONVERSION MULTIPLEXER: 1 TO 6 OR 6 TO 1 HIGH "SINK" AND "SOURCE" CURRENT
L9305A DUAL HIGH CURRENT RELAY DRIVER
L9305A DUAL HIGH CURRENT RELAY DRIVER. HIGH OUTPUT CURRENT HYSTERESIS INPUT COMPARATOR WITH WIDE RANGE COMMON MODE OPERATION AND GROUND COMPATIBLE INPUTS INPUT COMPARATOR HYSTERESIS INTERNAL THERMAL PROTECTION
ST485 LOW POWER RS-485/RS-422 TRANSCEIVER
LOW POWER RS-485/RS-422 TRANSCEIVER LOW QUIESCENT CURRENT: 300µA DESIGNED FOR RS-485 INTERFACE APPLICATIONS -7V TO 12V COMMON MODE INPUT VOLTAGE RANGE DRIVER MAINTAINS HIGH IMPEDANCE IN 3-STATEORWITHTHEPOWEROFF
M74HC4049TTR HEX BUFFER/CONVERTER (INVERTER)
HEX BUFFER/CONVERTER (INVERTER) HIGH SPEED: t PD = 8ns (TYP.) at V CC =6V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28 % V CC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
TS374 LOW POWER QUAD CMOS VOLTAGE COMPARATOR
LOW POWER QUA CMOS VOLTAGE COMPARATOR WIE SINGLE SUPPLY RANGE OR UAL SUPPLIES 3V TO 6V OR ±.5V TO ±8V VERY LOW SUPPLY CURRENT:.mA/COMP INEPENENT OF SUPPLY VOLTAGE EXTREMELY LOW INPUT BIAS CURRENT : pa