1010/T Series Incandescent Illuminator

Transcription

1 1010/T Series Incandescent Illuminator Installation and Operating Instructions This manual describes the installation and operating procedures for the American Dynamics 1010/T Series Illuminator. Before installation is started, become familiar with all the special features and warnings associated with this equipment. Once installation is complete, store this manual in a safe, convenient location for future reference.

2 Table of Contents Description... 1 Features... 1 General Safety... 1 Installation... 2 Mounting... 2 Connection... 2 Twilight Switch... 2 Lens Selection... 2 IR Illumination Area-vs-Distance... 2 Bulb Replacement... 3 Troubleshooting... 4 Dimensions... 5 Page Specifications... Back Page Information furnished by AMERICAN DYNAMICS is believed to be accurate and reliable. However, no responsibility is assumed by AMERICAN DYNAMICS for its use; nor for any infringements of other rights of third parties which may result from its use. No license is granted by implications or otherwise under any patent or patent rights of AMERICAN DYNAMICS.

3 DESCRIPTION Figure T Infrared Illuminator DESCRIPTION The 1010T Series Infrared Illuminator provides outstanding results when used with IR sensitive black/white cameras. The light produced by the 1010T Series is invisible to the human eye. This feature is excellent for covert security or where the addition of visible lighting is not possible. The 300 watt spot-lamp is designed to project a highly concentrated IR beam to a distance of 460 feet (140 m), covering an area 100 ft wide x 66 ft high. Pronounced ribbing around the two-part black enameled housing dissipates heat to extend bulb life. The IR filter is a lamination of vaporized-metal coated glass and Pyrex subjected to a special hardening process. A 10 ft (3 m) pendant line cord is standard with the Illuminator. FEATURES 120 VAC Input GENERAL SAFETY Observe the following safety instructions without fail: The 1010T generates large amounts of heat from the IR lamp during operation. Determine that no systems (sprinklers, thermostats, heating vents, etc.) in the immediate installation area are triggered or damaged as a result of this thermal radiation (heat).! CAUTION The concentrated high power of the Infrared beam can cause serious damage to a person's vision! Maintain a minimum 33 foot (10 m) safety zone between the Illuminator and any human contact. Before performing any service on or around the 1010T, shut down the Illuminator and isolate it electrically to prevent accidental operation. A cool-off period of approximately one hour is required after shut down. (Even if the housing is cool, the IR lamp may still retain enough heat to cause injury.) 300 Watt Bulb Weatherproof Housing 10 ft (3 m) Heavy Duty Pendant Line Cord 1

4 INSTALLATION INSTALLATION Mounting The 1010T IR Illuminator is supplied with a "U-shaped" bracket for mounting the Illuminator to a wall bracket or a Pan/Tilt mechanism. Ensure the structural soundness of the mounting bracket support surface. Three holes are drilled in the bottom of the mounting bracket (see Figure 2): Use the center hole (0.83"/21 mm) to secure the 1010T to a mounting bracket. Use the two side holes (0.28"/7 mm) to secure the 1010T to a Pan/Tilt unit. 4.25"/108 mm 0.56"/14.3 mm 2.75"/70 mm Lens Selection for 1010/T Table 2 lists the minimum focal length lens size required to focus at the maximum spotlight beam range for a particular camera format. Table 2 - Minimum Focal Length Lens Size Maximum Range Camera Format 460 (feet) 1" 2/3" 1/2" 1/3" Lens Size 75 mm 52 mm 37.5 mm 26 mm IR Illuminated Area -vs- Distance The beam transmitted by the 1010/T provides effective IR illumination to 460 feet (140 meters). Table 3 lists the spotlight area covered by the beam. Table 3 - Distance -vs- Area Table Distance* Area Covered [Horiz x Vert] Connection The 1010T requires a 120 VAC (2.5 Amps) supply voltage. The 1010T is supplied with a 10 ft (3 m) pendant line cord for connecting to a power supply (see Table 1). Leads Green White Black Twilight Switch 0.28"/7 mm 0.83"/21 mm Figure 2 - Mounting Bracket Drill Holes Table T Wiring Color Code Designation Ground 120VAC Hot 120VAC Neutral Routing the supply voltage through a twilight switch (not supplied) extends the operational life of the 1010T. American Dynamic's recommends using one twilight switch (AD part number 1010/TS) to operate a maximum of three Illuminator units. 50 ft (15.2 m) 11 x7 ft (3.3 x 2.1 m) 75 ft (22.3 m) 16 x 10 ft (4.9 x 3.1 m) 100 ft (30.5 m) 21 x 14 ft (6.4 x 4.3 m) 125 ft (38.1 m) 26 x 17 ft (7.9 x 5.2 m) 150 ft (45.7 m) 32 x 21 ft (9.8 x 6.4 m) 175 ft (53.3 m) 37 x 24 ft (11.3 x 7.3 m) 200 ft (61 m) 42 x 28 ft (12.8 x 8.5 m) 225 ft (68.6 m) 47 x 31 ft (14.3 x 9.5 m) 250 ft (76.2 m) 53 x 35 ft (16.2 x 10.7 m) 275 ft (83.8 m) 58 x 38 ft (17.7 x 11.6 m) 300 ft (91.4 m) 63 x 42 ft (19.2 x 12.8 m) 325 ft (99.1 m) 68 x 45 ft (20.7 x 13.7 m) 350 ft (106 m) 74 x 49 ft (22.6 x 14.9 m) 375 ft (114 m) 79 x 52 ft (24.1 x 15.9 m) 400 ft (122 m) 84 x 56 ft (25.6 x 17.1 m) 425 ft (130 m) 89 x 59 ft (27.2 x 18.0 m) 450 ft (137 m) 95 x 63 ft (29.0 x 19.2 m) 475 ft (145 m) 100 x 66 ft (30.5 x 20.1 m) 500 ft (152 m) 105 x 70 ft (32.0 x 21.4 m) *Distances from light source to subject 2

5 BULB REPLACEMENT BULB REPLACEMENT Before servicing the Illuminator, power down the unit and allow approximately one hour to cool. Replacement bulbs can be ordered through American Dynamics (part # AD1010/TBB). IR bulb replacement is done without removing the Illuminator from its mount. Remove the three 4 mm Hex screws holding the main housing to the rear housing (see Figure 3). Pull the defective IR bulb forward and gently remove the power cord connector from the IR bulb prongs. Remove and save the O-Ring (red colored gasket) around the defective bulb. Discard the defective bulb. Fit the O-ring (red colored gasket) around the new IR bulb and plug in the power cord connector taking care not to crack the porcelain base of the connector. Check that the IR bulb O-Ring is properly seated between the new bulb and the rear housing. Refer to Figure 3. Check that the weather seal (black colored gasket) is properly seated in the rear housing outer rim. Insert the IR lamp into the main housing. Close the housing and secure the three 4 mm Hex screws. IF YOU ENCOUNTER ANY PROBLEMS OPERATING THIS UNIT, OR NEED TECHNICAL ASSISTANCE, CALL OUR TECHNICAL SUPPORT CENTER AT: within the United States: outside the United States: (914) Rear Housing Weather Seal O-Ring Main Housing Power Cord w/connector Replacement Bulb Figure 3 - Bulb Replacement 3 4mm Hex Screw

6 TROUBLESHOOTING CAUTION Do not look directly into an operational Illuminator!!! Since IR light is invisible to the human eye, the only method of verifying a malfunctioning IR lamp is at the video output location. Before starting any maintenance work on the 1010T, be certain that the video system (i.e. cameras, monitors, etc.) is functioning properly. CAUTION Do not attempt to service an operational Illuminator! The heat generated by the IR lamp is sufficient to cause SEVERE BURNS. Before performing any service on or around the 1010T, shut!! down the Illuminator and isolate it electrically to prevent accidental starting. A cool-off period of approximately one hour is required after shut down. (Even if the housing is cool, the IR lamp may still retain enough heat to cause injury.) PROBLEM POSSIBLE CAUSE SOLUTION Lamp does not come on No 120 VAC to Lamp... Check 120 VAC power... Check twilight switch operation (if used) Bulb burned out... Check bulb connection socket... Replace bulb Bulb burns out frequently Lamp operating during daylight hours... Install twilight switch Moisture getting into housing... Check weatherseal... Tighten the 3 housing screws Poor image quality on video monitor Camera not sensing IR wavelengths... Check that camera is sensitive to IR light Camera does not resolve distant objects... Poor connections causing low AC voltage... Bulb is near end of service life, replace bulb 4

7 DIMENSIONS 7.5" 190 mm 9.45" 240 mm 8.27"/210 mm 7.48"/190 mm Figure /T Dimensions 5

8 SPECIFICATIONS SPECIFICATIONS Power: Operating Voltage: Current Consumption: Infrared Wavelength: Beam Dispersion: Normal Light Range*: Weatherproof Standard: Service Life (MTBF): Weight: 300 Watt 120 VAC 2.5 A 850 nm 12 H x 8 V 460 ft/140 m NEMA-4 (IP65) >2000 Hours (Bulb) 5.5 pound / 2.5 Kg Dimensions: (9.45 H x 8.27 W x 7.48 D) inches (240 H x 210 W x 190 D) mm * Normal range is based on the use of a CCD camera with maximum IR-sensitivity, medium scene reflectance. ACCESSORIES AD1010/TBB: AD1010/TS: AD1050/PL: AD1050/PT: AD1050/HL: AD1050/HP: 300 watt, PAR 56, bulb Dusk-to-dawn switch (will operate 3 units) "L" Bracket - one IR Illuminator on Patriot Series Pan/Tilt "T" Bracket - two IR Illuminators on Patriot Series Pan/Tilt "L" Bracket - one IR Illuminator on Hercules Series Pan/Tilt "T" Bracket - two IR Illuminators on Hercules Series Pan/Tilt OP1010T C April 1994 An American Dynamics Product Designed and built by Sensormatic CCTV Systems Division One Blue Hill Plaza Pearl River, New York, Business: (914) Technical Support Center: FAX: (914) Made in U.S.A.