ASSEMBLY AND INSTALLATION INSTRUCTIONS
|
|
- Griffin Walsh
- 5 years ago
- Views:
Transcription
1 T0436 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS. Hardware Package (included): Fixture Mounting Screw Mounting Screw X2 Mounting Strip Wire Connector X3 Important to Know: Features: 1. If you are not familiar with state and local electrical codes, it is recommended that you consult with a qualified electrician. 2. This fixture requires a 120 VAC, 60 Hz power source. 3. For general safety and to avoid any possible damage to the sensor, be sure the power is switched "off" before adjustment. Maximum Wattage: 22 W Working Temperature Range: - 4 F ~ 113 F 1. Energy saving LED fixture. 2. Motion sensor: turns light ON automatically when motion is detected and turns light OFF automatically when motion stops. 3. Photocell keeps the light OFF during daylight hours. 4. When in manual override mode, use wall switch to change the function and perform the function conversion. Note: Fixture can be wall mounted only. Read notes section on page 2 for additional information about mounting location of fixture. Light fixture should be mounted as shown when installed. Wall Mounted Page 1 / 6
2 Wire Connector(G) FRONT Decorative cover Fixture Mounting Screw Outlet Box Mounting Strip Mounting Screw Installation Steps Turn off the power at fuse or circuit box. 1. Install the mounting strip to the outlet box with the stamped word FRONT facing away from the outlet box, using two mounting screws that best fit the outlet box. Back plate should sit flush against wall surface when secured. (Choose one matching pair of suitable mounting screws from the 3 pairs provided) 2. Pull out the source wires from the outlet box. Make wire connections using wire connectors as follows: ---Connect the black wire from the fixture to the hot wire from the power source. (usually black) ---Connect the white wire from the fixture to the neutral wire from the power source (usually white). Carefully tuck the wires back into the outlet box. 3. Place fixture light against the outlet box, insert the fixture mounting screw through the fixture light hole, thread fixture mounting screw into the center hole of the mounting strip. Tighten the fixture mounting screw securely. Push the decorative cover firmly into the fixture mounting screw hole on the light fixture. When mounting to a wall, the UP arrow must point upward. Fig.1 4. With silicone caulking compound (not included), caulk completely around where the back plate of the fixture the wall surface. CAUTION: Be sure to caulk completely where the plate meets the wall surface to prevent water from seeping into the light fixture (C)and/or outlet box ( See Fig 1). Turn on the power at the main fuse or circuit breaker box. Function and operation Note:Before operating the function, please open the decorative cover of the light body at the bottom, and then recovery the decorative cover after operating. See Fig.2 Fig.3 Fig. 2 Sensitivity of Motion Sensor: 1. You can adjust the sensitivity of the motion sensor by using the SENSITIVITY selector located on the right side of the bottom surface of light body. 2. Adjust motion sensor sensitivity to achieve desired performance. Fig.3 3. Approximate range for each setting from 5ft to 40ft. Note: When power is first applied, the light will be on immediately. Waiting for 20 seconds to allow the sensor to warm up. TIME OFF AUTO PC 5S TEST SENSITIVITY 3MIN Page 2 / 6
3 Function and Operation 1. TEST MODE (daytime and nighttime operation.) With the power on, the owl s eyes turn to low-level brightness automatically and wall light is always on. The owl s eyes and wall light turn to high-level brightness when motion is detected, and stay on as long as the motion continues. Then the owl s eyes switch back to low-level brightness about 5 seconds after motion is no longer detected. 2. OFF MODE (nighttime operation only) To shift to the OFF mode, slide the switch to OFF position, and rotate Time knob to the desired time setting (between 5 seconds and 3 minutes). At dusk, the owl s eyes and wall light will be off, When the motion is detected, both the owl s eyes and wall light will be on at full brightness, When no longer movement, the owl s eyes and wall light at full brightness remain on for the predetermined time you set (5s ~ 3min), after then the light turns off automatically. Fig. 4 The light turns off automatically at dawn. 3. AUTO MODE (nighttime operation only) To shift to the AUTO mode, slide switch to AUTO position, and rotate Time knob to the desired time setting (between 5 seconds and 3 minutes). At dusk,the wall light is always on and the owl s eyes turn on at low brightness, When motion is detected, the owl s eyes turn to full brightness and stay on as long as motion continues. When the motion is no longer detected,the owl s eyes at full brightness remain on for the predetermined time you set (5s ~ 3min), and then the owl s eyes switch back to low level automatically. The light turns off automatically at dawn. TIME OFF AUTO PC 5S TEST SENSITIVITY 3MIN 4. PC MODE (nighttime operation only) The owl s eyes and wall light turn on at full brightness at dusk and remain ON until dawn. 5. Manual Override (nighttime operation only) To shift to the manual override mode, set the mode selector to OFF AUTO mode. Turn the wall switch OFF, and turn it ON twice within 3 seconds. The light will remain on all night long. To shift back to OFF AUTO mode, turn the wall switch OFF, and turn it ON twice within 3 seconds again. The light turns off automatically at dawn. Note: To make sure the above functions operate properly, always keep the wall switch in the ON position (including the daytime). Manual Override Operation Diagram Turn wall switch OFF-ON -OFF-ON in 0.5~3 Seconds OFF AUTO MODE Fig. 5 Manual Override Turn wall switch OFF-ON -OFF-ON in 0.5~3 Seconds Customization Options Shut-off Delay The shut-off delay is the length of time the light will stay at full brightness after motion is detected. You can set the shut-off delay by rotating the Time Delay knob so it points to the desired time setting(from 5 seconds to 3 minutes). To increase the shut-off delay, turn the knob clockwise. To decrease the shut-off delay, turn the knob counterclockwise. Notes: 1. The sensitivity of the motion sensor will increase as the environmental temperature gets cooler. For best performance, gently clean the lens with a soft cloth every 1 or 2 months to ensure maximum sensitivity. 2. For best performance, install fixture at least 6-8 feet above the ground. At such a height, the fixture will provide a detection distance of up to 40 feet at 77 degrees Fahrenheit. (See Fig.6) 3. The sensor detects movement across a detection range of 120 degrees. (See Fig.7) 4. The sensor will be more sensitive to motion across its detection path than motion directly towards it. (See Fig.8) 5. To reduce possible nuisances, do not mount the fixture near a heat source like an air conditioner, vent or furnace exhaust, or in a direction facing any reflective object or other nearby light source. Page 3 / 6
4 Fig.8 Be sure the light is mounted straight on the wall otherwise, the detection distance may be limited. Fig ' 6.0' 5' Motion Motion Fig Least sensitive 40' Sensor Most sensitive TROUBLE SHOOTING Problem The light will not come on. The light comes on during the day. The light comes on for no apparent reason. The light turns off too late in the PC setting. Possible Cause Solution The light switch is turned off. Turn the light switch on. The fuse is blown or the circuit breaker is turned off. Replace the fuse or turn the circuit breaker on. Daylight turn-off (photocell) is in effect. Recheck after dark. The circuit wiring is incorrect (if this is a new installation). Verify the wiring is correct. The motion sensor is aimed in the wrong direction. Re-aim the motion sensor to cover the desired area. The outside air temperature is close to the same as a person s body heat. Increase the SENSITIVITY setting. The motion sensor may be installed in a relatively dark location. The light fixture is operating normally under these circumstances The TIME switch is in the TEST position. Set the TIME switch to the 5s to 3 minute setting. The motion sensor may be sensing small animals or automobile traffic. Decrease the SENSITIVITY setting or reposition the motion sensor. The SENSITIVITY switch is set too high. Decrease the SENSITIVITY setting. The switch is in the PC setting. The light fixture is operating normally under these circumstances. The outside temperature is much warmer or cooler than a person s body heat (summer or winter). Decrease the SENSITIVITY setting. The light fixture is wired through a dimmer or timer. Do not use a dimmer or timer to control the light fixture. Replace the dimmer or timer with a standard on/off wall switch. The light fixture may be installed in a relatively dark location. Relocate the light fixture setting. Page 4 / 6
5 Problem The light stays on continuously. The light flashes on and off. The light flashes once then stays off in manual mode. Possible Cause Solution The motion sensor may be picking up a heat source, such as an air vent, dryer vent, or brightly painted, heat-reflective surface. The motion sensor is in manual mode. Decrease the SENSITIVITY setting or reposition the motion sensor. The light fixture is wired through a dimmer or timer. Do not use a dimmer or timer to control the light fixture. Replace the dimmer or timer with a standard on/off wall switch. The light fixture is on the same circuit as a motor, transformer, or fluorescent bulb. Install the light fixture on a circuit without motors, transformers, or fluorescent bulbs. Heat or light from the lamp heads may be turning the motion sensor on and off. Reposition the lamp heads away from the motion sensor. Heat is being reflected from other objects and may be turning the motion sensor on and off. Decrease the SENSITIVITY setting or reposition the motion sensor. The motion sensor is in TEST mode and warming up. While in TEST mode, the light only stays on for 5 seconds. Set the TIME switch to 5s to 3 minutes. The motion sensor is detecting light from Reposition the lamp heads to keep the area below the motion sensor Switch the motion sensor to auto. See Using manual mode on page 4. the lamp heads. relatively dark. If unable to fix any of the above issues, please consult a certified electrician. The following parts are available for re-order if damaged or missing. Spare Parts List: Assembly Kit 5892MM (1 SET) Mounting Screw X2 Mounting Strip Fixture Mounting Screw Wire Connector X3 Page 5 / 6
6 5-YEAR LIMITED WARRANTY: All products are warranted to be free of defects in material and workmanship for five (5) years from date of purchase. This warranty is limited to the correction of any such defect, or the replacement of any such defective item(s), provided that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item(s) is / are returned with proof of purchase date; and (c) it is found upon inspection by us that the item(s) is / are defective as noted above. This warranty does not cover labor costs, consequential damages, nor does it apply to any item(s) that have been improperly installed, overloaded, altered, or otherwise abused by the customer, its agent(s) or employee(s). Finishes are specially excluded from the terms of this warranty since they are subject to environmental maintenance deemed beyond our control. Other than the described obligation, we assume no further liability with respect to the sale or use of our products.we make no warranty, express or implied, and disclaim any warranty of merchantability or fitness for a particular purpose. A:7-1/4" B B: 9-1/2" C: 4-1/2" A C Page 6 / 6
ASSEMBLY AND INSTALLATION INSTRUCTIONS
T0412 / T0413 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS. Hardware
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS
T0103 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local
More informationMounting Bracket Screw
Sku Number: 356-9243/9244 INDUCTION LAMP Model Number: E6956W/E6956BZ PACKAGE CONTENTS Questions, problems, missing parts? Before returning to your retailer, call our customer service at 1-800-887-6326
More informationINSTRUCTION MANUAL. 1 Light Exterior Wall Lantern. Home Depot SKU (UPC ) Home Depot SKU (UPC ) (Prairie Bronze)
INSTRUCTION MANUAL 1 Light Exterior Wall Lantern Home Depot SKU 477405 (UPC 718212230107) Home Depot SKU 495682 (UPC 718212230282) (Prairie Bronze) Page 1 Thank you for purchasing this Hampton Bay exterior
More informationSmart Task Motion Activated Task Light Installation Manual
Smart Task Installation Manual STASK24 STASK21 STASK12 1 SENSOR SPECIFICATIONS: Voltage: 120 Volts AC, 60Hz UL Listing: For Indoor applications Time Adjustment: 5 seconds to 15 minutes Sensor Construction:
More informationTRANSFORMER HD-HAMPTON HAMPTONBAY.COM
Item #1001 510 115 Model DIY-600PS USE AND CARE GUIDE TRANSFORMER Questions, problems, missing parts? Before returning to the store, call HamptonBay Customer Service 8 a.m. - 7 p.m., EST, Monday Friday,
More informationInstallation Instructions SKU# , Rated Voltage V~ 50Hz
Installation Instructions SKU# 240621, 240622 Rated Voltage 220-240V~ 50Hz THANK YOU FOR PURCHASING THIS QUALITY LUCCI PRODUCT, TO ENSURE CORRECT FUNCTION AND SAFETY, PLEASE READ AND SAVE ALL INSTRUCTIONS
More informationWALL LANTERN ITEM # MODEL #LWS1204C ATTACH YOUR RECEIPT HERE. Serial Number. Purchase Date
Portfolio is a registered trademark of LF, LLC. All Rights Reserved. ITEM #0338651 WALL LANTERN MODEL #LWS1204C ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts?
More informationInstallation Instructions
SPECIFICATIONS WS-200 Automatic PIR Wall Switch Voltages...........................120 or 277VAC, 60Hz Requirements @ 120VAC, 60Hz........0-800W ballast & tungsten @ 277VAC, 60Hz.................0-1200W
More informationInstallation Instructions
TECH SUPPORT The Watt Stopper, Inc. 2800 De La Cruz Blvd. Santa Clara, CA 95050, USA Tel: 1(800)879-8585 1(972)578-1699 Fax: 1(972)422-1311 www.wattstopper.com Outdoor 180 & 270 PIR Motion s Model#s: EW-100-120
More informationGLASS GLOBE MOBILE LINEAR CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [7] (E) Screws [6] (F) Nuts [5] (G) Extension rods [15] (H) Transformer [1] (I) Threaded inserts [5] (J) 1.6W LED
More informationNash Chandelier Assembly and Installation Instructions
CAUTION: Nash Chandelier Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. Important
More informationMADELINE METAL CHANDELIER
MADELINE METAL CHANDELIER Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationWoven Leather Chandelier Large Assembly and Installation Instructions
CAUTION: Woven Leather Chandelier Large Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY
More informationCX-100. Installation Instructions. PIR Occupancy Sensor SPECIFICATIONS
SPECIFICATIONS CX-1 PIR Occupancy Sensor Voltage... 24VDC Current Consumption... 19mA* Power Supply... WattStopper Power Pack Isolated Relay Rating... 1A@24VDC Time Adjustment... 15 seconds 3 minutes Sensitivity
More informationMini Sensor. Outdoor Motion Sensor. Installation Manual
Mini Sensor Outdoor Motion Sensor Installation Manual 1 Contents: Why RAB Sensors are BEST for You? Smaller is better! Mini Sensor uses state-of-the-art surface mount technology (SMT), just like cellular
More informationArched Top Lantern Pendant Assembly and Installation Instructions. Country of Destination: US/CN UK/EU/AUS Middle East
CAUTION: Arched Top Lantern Pendant Assembly and Installation Instructions Country of Destination: US/CN UK/EU/AUS Middle East BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF
More informationCustom Pendant- Hardwire Assembly and Installation Instructions
Custom Pendant- Hardwire Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationInstallation Instructions
WS-250 & WS-250-347 Passive Infrared Wall Switch Occupancy Sensor SPECIFICATIONS WS-250 Voltages...120 or 277VAC, 60Hz Load Requirements @ 120VAC, 60Hz... 0-800W ballast & tungsten, 1/6 hp @ 277VAC, 60Hz...
More informationROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS
ROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. IMPORTANT
More informationMaxLite Linear Strip ECO Series
General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions
More informationFabric tiered drum pendant 30in Assembly and Installation Instructions
CAUTION: Fabric tiered drum pendant 30in Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY
More informationInstallation Manual. Specifications: Cautions: TURN OFF ALL POWER AT CIRCUIT BREAKER / FUSE PANEL.
Specifications: Installation Manual The STEALTH360 is the most reliable and technically advanced motion-activated light control ever produced. This technical manual is written for electrical professionals
More informationSmart Post RAB. Installation Manual. Outdoor Motion Sensor. It s easy to add. motion detection to your post lantern! Contents.
Smart Post Outdoor Motion Sensor Installation Manual Contents Specifications 180º coverage 360º coverage SPOST500/180 SPOST180HL/180 It s easy to add motion detection to your post lantern! SPOST500 SPOST180HL
More informationGLASS GLOBE MOBILE 6-ARM CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [6] (E) Screws [4] (F) Nut [1] (G) Extension rods [3] (H) Transformer [1] (I) Arm counterweights [6] (J) 1.6W LED
More informationCONTENTS OF THE BOX. *PIR sensor only **Dual Technology and PIR sensors only. Description PIR Ultrasonic Dual Technology
Instruction Bulletin 63249-420-283A4 08/2009 Wall Mount Occupancy Sensor SLSWPS1500, SLSWUS1500, SLSWDS1500 INTRODUCTION Wall Mounted Occupancy Sensors are Class 2 devices ideal for use in business or
More information3000W multi Pir light controller
3000W multi Pir light controller Cat No. MLB3000 - Black Cat No. MLW3000 - White Installation & Operating Instructions INSTALLATION & operating instructions SECTION ONE GENERAL INFORMATION The unit utilises
More informationSmartBox RAB. Installation Manual. Outdoor Motion Sensor. It s easy to add. motion detection to all your outdoor lights! Contents.
SmartBox Outdoor Motion Sensor Installation Manual Contents It s easy to add motion detection to all your outdoor lights! RAB Specifications Switching Capacity: Relay On/Off Model: 500 watts Incandescent
More informationPARTS INCLUDED TOOLS & PARTS NEEDED Do not mount on vibrating surfaces. appro to 2.5 meters 12M
Type: RH60B-LED Ref: 86524 The bulkhead light incorporates a PIR (Passive Infra Red) sensing device which continuously scans a preset operating zone and immediately switches the lamp on when it detects
More informationVanity top, faucet and drain not included. 1-3/8 screws (x 2) (for middle and bottom drawers) Knobs (x 5)
ASHWELL VANITY BASE INSTALLATION INSTRUCTIONS Nutmeg models: 30176, 30177, 30178, 30179 Dark chocolate models: 30183, 30184, 30185, 30186 Gray models: 30190, 30191, 30192, 30193 Matte white models: 30197,
More informationInstallation Instructions
WS 301/WS-301-347 Passive Infrared Wall Switch Occupancy Sensor WS-301 SPECIFICATIONS WS-301-347 WS-301 Voltages...120 or 277VAC, 50/60Hz Load Requirements @ 120VAC...0~1000W ballast, E-ballast, LED, tungsten,
More informationMANCHESTER VANITY BASE
MANCHESTER VANITY BASE INSTALLATION INSTRUCTIONS Questions? Call our customer service department at 1-855-995-5578, 8:30 a.m. - 5 p.m., EST, Monday - Friday or e-mail: contactus@magickwoods.com. Models:
More informationVista SCREEN. and Double Door Link Kit. Installation Manual for. For Double Doors (French Doors) Quick and Easy to Size and Install
and Double Door Link Kit Installation Manual for Vista SCREEN TM Quick and Easy to Size and Install For Double Doors (French Doors) Durable. Reliable. Attractive. For door openings up to 72 13 /16 (1,849
More information2011 / Circuit Tracer
INSTRUCTION MANUAL 2011 / 00521 Circuit Tracer Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. 52044992 2008 Greenlee Textron
More informationRiverside. Windward Bay EntertaInment Wall System Assembly Instructions. Made In Viet Nam. Right Pier. Bridge & Back Panel.
EntertaInment Wall System Page 1 of 12 Product No. 42840 42848 42849 42843 Product Description Console Left Pier Right Pier Bridge & Back Panel Right Pier Bridge & Back Panel Left Pier 63" Inch Ent. Console
More informationRESIDENTIAL MOTORIZED STORAGE UNIT
BY V-BRO PRODUCTS RESIDENTIAL MOTORIZED STORAGE UNIT Model: GGR220 INSTALLATION AND OPERATING INSTRUCTIONS Distributed Exclusively by V-BRO PRODUCTS For technical questions and replacement parts, please
More informationWARNING: Do not work around outlets while the power is on. Do not stick fingers or tools into an electrical box while the power is on.
Instructions for SnapRays Guidelights WARNING Failure to turn OFF electrical power prior to installation of the Guidelight can result in electrical shock, fires, and/or death. www.snappower.com CAUTION:
More informationVista SCREEN. Installation Manual for. For left hinged doors. Quick and Easy to Size and Install
Installation Manual for Vista SCREEN For left hinged doors Quick and Easy to Size and Install Durable. Reliable. Attractive. For door openings up to 36 (914mm) wide and 81 3 /16 (2,062mm) high QC03-0512L
More information5001 INSTALLATION AND OPERATING INSTRUCTIONS
5001 INSTALLATI AND OPERATING INSTRUCTIS IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATI INSTRUCTIS DO NOT ATTEMPT TO INSTALL OR OPERATE INTRODUCTI This SKYTECH remote control system was developed to
More informationAssembly & Installation Instructions
1 OF 6 Component Parts A Fixture Pipe (3) B Coupling (3) C Canopy Pipe (3) D Middle Canopy Can E Clutch (3) F Plastic Sleeve (3) G Side Canopy Can (2) H Set Screw (3) I Middle Crossbar J #10 Screws (4)
More informationInigo Sconce INSTALLATION INSTRUCTIONS P _2_A 1 of 5
P31321 1 of 5 Thank You For Choosing Kallista We appreciate your commitment to Kallista quality products. Please take a moment to review this manual before you install your Kallista product. If you encounter
More information3000W MULTI PIR LIGHT CONTROLLER
3000W MULTI PIR LIGHT CONTROLLER Cat No. MLB3000 Black Cat No. MLW3000 White Installation & Operating Instructions INSTALLATION & OPERATING INSTRUCTIONS E G Dusk/Dawn Time Override/Holiday Mode F H Lens
More information18W Nightsensor Bulkhead
18W Nightsensor Bulkhead Cat No. ECO18P instructions Instructions A Retaining clip B Vertical location Sensor Horizontal location Sensor Wall fixing hole C Wall fixing hole D Wall fixing hole Sensor Vertical
More informationFFLED18 INSTALLATION INSTRUCTIONS
FFLED18 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We d like to hear your comments. Call the Marketing
More informationFFLED18 INSTALLATION INSTRUCTIONS
FFLED18 INSTALLATION INSTRUCTIONS Thank you for buying RC lighting fixtures. Our goal is to design the best quality products to get the job done right. We d like to hear your comments. Call the Marketing
More informationTilting, Swiveling & Rotating Flat Panel Wall Mount
Tilting, Swiveling & Rotating Flat Panel Wall Mount Model: VXA980TC +5 to -5 +5 to -5 Supports most 0-80 Flat Panel TVs Maximum Weight Capacity: 32 lbs. Supports VESA Sizes up to 600x500 For technical
More informationRadiant Pro 2500 Video Light (Cat. No. 6047)
Fantasea Line Radiant Pro 2500 Video Light (Cat. No. 6047) Instruction Manual 1 TABLE OF CONTENTS TABLE OF CONTENTS... 2 DISCLAIMER... 3 INTRODUCTION... 3 GENERAL INFORMATION... 3 SPECIFICATIONS... 4 INCLUDED
More informationv3 360 Passive Infrared Line Voltage Occupancy Sensor
SPECIFICATIONS CI-355 v3 360 Passive Infrared Line Voltage Occupancy Sensor with Light Level feature Voltages... 120//230/277/347VAC, 50/60Hz Load Ratings @120VAC...0-800W Ballast/Tungsten/LED @230VAC
More informationUniversal Projector Ceiling Mount Model: DPM-45
Universal Projector Ceiling Mount Model: DPM-45 Instruction Manual Images may different from actual product Disclaimer It is Dyconn s intention to have all the correct information represented within this
More informationSTL200/277 Installation Manual STL200/277
STEALTH STL200/277 Installation Manual STL200/277 Specifications: Switching Capacity: Voltage: Detection Pattern: Time Adjustment: Power Consumption: Surge Protection: 8 amps 277 volts 1000 watts incandescent
More informationSTL200/277 Installation Manual STL200/277
STEALTH STL200/277 Installation Manual STL200/277 Specifications: Switching Capacity: Voltage: Detection Pattern: Time Adjustment: Power Consumption: Surge Protection: 8 amps 277 volts 1000 watts incandescent
More informationAllegro Home Office Assembly Instructions. Tipping Restraint. Bun Foot W/ Leveler. 4 pcs.
email: info@riverside-furniture.com Allegro Home Office Assembly Instructions Components and Hardware List Page 1 of 5 Made in China Shelf Pin Wood Shelf File Rod & Clips 1/2"Wood Screw A 16 pcs. B 4 pcs.
More informationTurn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC Customer Service Phone 63.273.2700 Fax 63.23.702 www.quoizel. ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wire strippers,electricaltape,safetyglasses.
More informationTuff Dome. Installation Manual. vandal resistant. Outdoor Motion Sensor. Contents. Specifications. Switching Capacity:
Tuff Dome Vandal Resistant Outdoor Motion Sensor Installation Manual Contents It s easy to add vandal resistant motion detection to outdoor lights! Specifications Switching Capacity: Relay On/Off Model:
More informationCOMMERCIAL TRANSMITTER INSTRUCTIONS
READ THIS MANUAL CAREFULLY BEFORE BEGINNING COMMERCIAL INSTRUCTIONS MODELS: 831, 8833 OCS: 1-DOOR 733, 8833C OCS: 3-DOOR 639: 9-DOOR 535: 27-DOOR PRODUCT FEATURES Allstar Commercial Transmitters are designed
More informationTHIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2026 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationLOAD AWG Solid CU Wire Only LINE NEUT FSP-211. High/Low PIR Occupancy Sensor 230 VAC, 50 Hz 1200W max ballast 5E4
DESCRIPTION AND OPERATION The is a motion sensor that dims lighting from high to low based on movement. This slim, low-profile sensor is designed for installation inside the bottom of a light fixture body.
More informationMST-5. Varifan USER S MANUAL MST-5 5 STAGE THERMOSTAT. computer compatible ADJUST. 9 reduc. per day 8 7 F rel. rel. rel. rel.
MST-5 USER S MANUAL 5 STAGE THERMOSTAT computer compatible ALARM 1 2 3 4 5 ALARM F2 12 11 1 on off TIMER 2 PERIOD STAGE 2 10 3 rel Varifan LIMIT HEAT STAGES 9 reduc. per day 8 7 COOL STAGES 6 rel 5 4 COOL/HEAT
More informationUSER'S MANUAL DMR-4350
USER'S MANUAL DIGITAL MULTIMETER DMR-4350 CIRCUIT-TEST ELECTRONICS www.circuittest.com TABLE OF CONTENTS SAFETY Safety Information...................................... 2 Safety Symbols........................................
More informationAvanti Hearth Products Z60
Avanti Hearth Products Z60 INSTALLATION AND OPERATING INSTRUCTION If you are unable to read or understand these instructions do not attempt to install or operate Please keep these Instructions for future
More informationSTEALTH. STL200 Installation Manual. Specifications: STL200 STL200H STL200HB. Switching Capacity: 8 amps
STEALTH STL200 Installation Manual STL200 STL200HB STL200H Specifications: Switching Capacity: 8 amps Voltage: 120 volts 1000 watts Incandescent 500 watts Fluorescent Detection Pattern: 50 x 200 Time Adjustment:
More informationOLED-55 USER MANUAL OCTALUX LED. OctaLux LED - USER MANUAL 1
OLED-55 OCTALUX LED USER MANUAL OctaLux LED - USER MANUAL 1 OctaLux LED INTRODUCTION Thank you for choosing Genaray. The OctaLux LED Light Softbox produces bright, soft, and consistent light that s designed
More informationwith Light Level, Isolated Relay and Manual On features
DT-200 version 3 Dual Technology Low Voltage Occupancy Sensor with Light Level, Isolated Relay and Manual On features SPECIFICATIONS Voltage... 18-28VDC/VAC Current Consumption... 25mA Power Supply...WattStopper
More informationSTEALTH. STL110 Installation Manual. Specifications: STL110 STL110HB STL110H STL110R. Switching Capacity:
STEALTH STL110 Installation Manual STL110 STL110H STL110HB STL110R Specifications: Switching Capacity: Voltage: Detection Pattern: Time Adjustment: Power Consumption: Surge protection: UL Listing: 8 amps
More information120-WATT POWER PACK MODEL #00688
PORTFOLIO and PORTFOLIO & Design are trademarks or registered trademark of LF, LLC. ll rights reserved. ITEM #08086 20-WTT POWER PCK MODEL #00688 Español p. 9 TTCH YOUR RECEIPT HERE Serial Number Purchase
More informationCURATED CARTESIAN VANITY
CURATED CARTESIAN VANITY CONTENT Prep the wall - 3 Frame installation - 5 Attaching the side kits - 7 Installing any optional vanity accessories - 7 Sink assembly - 8 Insert the drawer - 10 Attaching glass
More informationSYSTEM OPERATING CONTROLS
SYSTEM OPERATING CONTROLS Master Station Controls 1 END CALL: Ends intercom communication and returns system to audio source. 2 DOOR TALK: Initiates intercom communication to the door speakers. 3 INSIDE/PATIO:
More informationInstallation Instructions
Designer Wall Switch Occupancy Single Pole (One Location) or Multi-Location Rated: 12/277V, 6Hz Cat. No. ODS1Ø-IDx Incandescent 8W - 6.67A @ 12V Fluorescent 12VA - 1A @ 12V 27VA - 1A @ 277V Supplemental
More information1410T/LCD-A INSTALLATION AND OPERATING INSTRUCTIONS
1410T/LCD-A INSTALLATION AND OPERATING INSTRUCTIONS IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS, DO NOT ATT TO INSTALL OR OPERATE INTRODUCTION This SKYTECH remote control system was
More informationNOVA-EXT Versatile Projector Mount Model: NOVA-EXT
INSTALLATION MANUAL NOVA-EXT Versatile Projector Mount Model: NOVA-EXT NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 800-368-9700 Fax: 800-832-4888 Other Locations
More informationThanks for shopping with Improvements! 7 ft. Wall Christmas Tree w/ Stand Item #419359
Thanks for shopping with Improvements! 7 ft. Wall Christmas Tree w/ Stand Item #419359 IMPORTANT: RETAIN FOR FUTURE REFERENCE. READ CAREFULLY. PARTS LIST: NOTES: (1) Tree Section A (1) Tree Section B (1)
More informationPhone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels
Phone # 800-440-8785 www.lajolladoors.com La Jolla Doors Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Thank you for choosing La Jolla Doors In this manual you will
More informationPage 1 T O O L S A N D M AT E R I A L S R E Q U I R E D. 1. Screwdriver 2. Carpenter's level 3. Electrical Tape PA R T S L I S T. A.
T O O L S A N D M AT E R I A L S R E Q U I R E D 1. Screwdriver 2. Carpenter's level 3. Electrical Tape PA R T S L I S T A. Cabinet B. Wood Screw X4 C. Plastic wire connector x3 Page 1 I M P O R TA N T
More informationQuadroMAX. Installation Manual. QM Series. LED Outdoor Lighting Fixtures REV: 3/22/16
QuadroMAX LED Outdoor Lighting Fixtures Installation Manual QM Series REV: 3/22/16 BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING Risk of fire or electric shock. Luminaire wiring
More informationBroadband Step-Up Transformer. User Manual
Broadband Step-Up Transformer User Manual 990-1930 09/2004 Introduction Introduction About this unit The APC Step-Up Transformer provides 220 V power from 60 VAC Broadband cable systems. Safety Electrical
More informationCIRCUIT-TEST ELECTRONICS
USER'S MANUAL Sweep Function Generator with Counter SWF-8030 CIRCUIT-TEST ELECTRONICS www.circuittest.com TABLE OF CONTENTS SAFETY INFORMATION...page 3 INTRODUCTION... 4 SPECIFICATIONS... 5 FRONT PANEL
More information3-1/4 HP VARIABLE SPEED PLUNGE ROUTER
IMPORTANT INFORMATION 2-YEAR LIMITED WARRANTY FOR THIS PLUNGE ROUTER KING CANADA TOOLS OFFERS A 2-YEAR LIMITED WARANTY FOR NON-COMMERCIAL USE. 3-1/4 HP VARIABLE SPEED PLUNGE ROUTER PROOF OF PURCHASE Please
More informationRadiant 3000F Video Light (Cat. No. 6052)
Fantasea Line Radiant 3000F Video Light (Cat. No. 6052) Instruction Manual 1 TABLE OF CONTENTS TABLE OF CONTENTS... 2 DISCLAIMER... 3 INTRODUCTION... 3 GENERAL INFORMATION... 3 SPECIFICATIONS... 4 INCLUDED
More informationRPS /02 Effective for models with serial numbers beginning with "G".
Instruction Sheet B2000 Cyclone Bender RPS-0097 0/02 Effective for models with serial numbers beginning with "G". IMPORTANT RECEIVING INSTRUCTIONS Visually inspect all components for shipping damage. If
More informationR PROFLAME Instruction Book Collection
9.956.028 R00 584 PROFLAME Instruction Book Collection 4-17 18-29 584 PROFLAME System 30-39 Appendix: DIP SWITCH NUMBER (0=ON 1=OFF) 40-41 4-17 Fig. 1 The SIT is a device that allows, in conjunction with
More informationComfort 10S Wall Hardwire Installation and Operations Manual
Comfort 10S Wall Hardwire Installation and Operations Manual 10/24/2012 REQUIRED TOOLS STARHEAD SCREWDRIVERS DRILL & BIT FLAT HEAD SCREWDRIVERS ALLEN KEY PENCIL MEASURING TAPE LEVEL ELECTRICAL REQUIREMENTS:
More information9 PIECE TUNGSTEN CARBIDE HOLE SAW KIT. Model 90721
9 PIECE TUNGSTEN CARBIDE HOLE SAW KIT Model 90721 Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ
More informationPORTABLE HALOGEN WORK LIGHT OWNER S MANUAL
PORTABLE HALOGEN WORK LIGHT OWNER S MANUAL L-9001 (29278) L-9002 (29276) WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules
More informationCAUTION: BEFORE INSTALLING THE LUMINAIRE, MAKE SURE THAT THE CURRENT IS CUT TO THE BOX FUSES / MAIN CIRCUIT BREAKER.
Hanging lamp with horn Assembly and installation instructions CAUTION: BEFORE INSTALLING THE LUMINAIRE, MAKE SURE THAT THE CURRENT IS CUT TO THE BOX FUSES / MAIN CIRCUIT BREAKER. Important safety instructions:
More informationMaintenance and other important non-personal injury and non-material damage instructions or statements that should be observed.
VIGO INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE ()! SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated
More informationManual Carton Closing Staplers
Operator s Manual Manual Carton Closing Staplers SHB00-A Item No. 6400 -/8" Crown Carton Closing Stapler 5/8" and /4" (5mm and 8mm) Ask for Genuine INTERCHANGE A58 and A4 Staples SHB50-C Item No. 640 -/4"
More informationOPERATION MANUAL MODEL
OPERATION MANUAL MODEL 60-511504 SUPPLIER CODE: GO-60-511504 BREEZER MESH OFFICE TASK CHAIR - GRAY/BLACK CUSTOMER SERVICE For fastest service, please visit our website at www.comfortproducts.net/support
More informationInstallation Instructions
Installation Instructions To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. P r o d u c t s Luxury Faucets and Accessories Jean Nouvel Product
More informationINTEGRATED HYBRID TUBE AMPLIFIER VT Model HYBRID TUBE AMPLIFIER
INTEGRATED HYBRID TUBE AMPLIFIER Model VT-40.2 HYBRID TUBE AMPLIFIER OWNER S MANUAL Safety Instructions The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert
More informationMM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationEco-$mart, Inc. TOLL FREE:(888) FAX:(941)
Eco-$mart, Inc. TOLL FREE:(888)329-2705 FAX:(941)377-9460 info@eco-smart.com www.eco-smart.com Fluorescent High Bay Occupancy Sensor Module Installation Instructions Hubbell Building Automation 9601 Dessau
More informationModel: Smart Stat III INSTALLATION AND OPERATION INSTRUCTIONS
Model: Smart Stat III INSTALLATION AND OPERATION INSTRUCTIONS INTRODUCTION IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT TO INSTALL OR OPERATE This remote control system
More informationApexDesk Assembly Guide
ELECTRIC HEIGHT-ADJUSTED SIT TO STAND DESK ApexDesk Assembly Guide REV-1507C Table of Contents CAUTION, USE & LIABILITY... 3 PARTS & HARDWARE LIST... 4 PARTS / COMPONENT DIAGRAMS... 5 ASSEMBLY INSTRUCTIONS...
More informationPORTROD WALL MOUNTED HEIGHT ROD
PORTROD WALL MOUNTED HEIGHT ROD USER INSTRUCTIONS P/N UMPORTROD Rev 1-052112 1 PORTROD Thank you for your purchase of this Health o meter Professional product. Please read this manual carefully, and keep
More informationModel: 5010 INSTALLATION AND OPERATING INSTRUCTIONS
Model: 5010 INSTALLATI AND OPERATING INSTRUCTIS INTRODUCTI IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATI INSTRUCTIS DO NOT ATTEMPT TO INSTALL OR OPERATE This SKYTECH remote control system was developed
More informationDatasheet ENGLISH Halogen lamp 120W with motion sensor ( ) Halogen lamp 400W with motion sensor ( )
Datasheet Halogen lamp 120W with motion sensor (791-8264) Halogen lamp 400W with motion sensor (791-8273) Attention: Please read the following instructions carefully to ensure that mounting operation will
More informationMini Receiver. Off Peak System Control. Operation & Installation Guide for Power Line Carrier WARRANTY. (Applicable to Software Version
MR9 WARRANTY Steffes Corporation ( Steffes ) warrants that the Steffes Power Line Carrier Mini Receiver is free from defects in materials and workmanship under normal use and service. Steffes obligation
More informationWARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE!
WARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE! General Safety Information To reduce the risk of death, personal injury or property damage from
More information9 QUICK RELEASE WOODWORKING VISE
9 QUICK RELEASE WOODWORKING VISE 94386 OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 349 Mission Oaks Blvd., Camarillo, CA
More informationDAWN TO DUSK SENSOR OWNER S MANUAL
DAWN TO DUSK SENSOR OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More information