Installation Instructions SKU# , Rated Voltage V~ 50Hz
|
|
- Denis Pearson
- 5 years ago
- Views:
Transcription
1 Installation Instructions SKU# , Rated Voltage V~ 50Hz THANK YOU FOR PURCHASING THIS QUALITY LUCCI PRODUCT, TO ENSURE CORRECT FUNCTION AND SAFETY, PLEASE READ AND SAVE ALL INSTRUCTIONS CAREFULLY BEFORE USING THE PRODUCT. WARRANTY: This light fitting is covered by a 12 month warranty; please retain proof of purchase and evidence of installation by a licensed electrician. INTRODUCTION: The Security Light incorporates a PIR (Passive Infrared) sensing device which continuously scans a preset operating zone and immediately switches the light on when it detects movement in that area. This means that whenever movement is detected within the range of the sensor, the light will switch on automatically to illuminate pathways, steps, patios, porches or whatever area you have selected to light for reasons of safety, convenience or security. While there is movement within range of the unit the light will remain on. WHERE TO FIT YOUR SECURITY LIGHT: To achieve best results, we suggest you take into account the following points: Ideally the security light should be mounted 1.8 to 2.5m (6 to 8 ft) above the area to be scanned (refer Fig. 1A) To avoid damage to unit, do not aim the sensor towards the sun. To avoid nuisance triggering, the sensor should be directed away from heat sources, such as barbecues, air-conditioners, other outside lighting, moving cars and flue vents. To avoid nuisance triggering, keep away from areas of strong electromagnetic disturbance. Do not aim towards reflective surfaces, such as smooth white walls, swimming pools etc. The security light scanning specifications (max 12meters and approx. 180º) may vary slightly depending on the mounting height and location. The detection range of the unit may also alter with temperature changes. Before selecting a place to install your security light, you should note that movement across the scan area is more effective than movement directly toward or away from the sensor and not across, the apparent detection range will be substantially reduced ( refer Fig. 1C) INSTALLATION AND SAFETY REQUIREMENTS: Must be installed by a Licensed Electrician. Must be installed according to the current wiring rules AS/NZS3000. Do not exceed the maximum wattage rating.
2 INSTALLATION DIRECTIONS: Take care not to pull any electrical wires during unpacking as this may damage the connection. Layout all the components on a smooth surface and make sure there is no component s missing before assembling. Check whether the fitting has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement. Ensure all power has been isolated for your own safety. The fitting is rated to IP44, which means it is protected against splashing water from any direction. 1. Select a suitable location for installation. Ensure the fitting is not installed next to any air vents and is not in any moist or damp areas. 2. This fitting must be earthed. 3. Run the wiring as the following diagram (Fig. 2) using clamp connectors supplied, and ensure that the gasket is in position. Please double check the correct connections after wiring, the metal base must be connected to the earth terminal. 4. Attach the security floodlight to the mounting plate. 5. Insert the PAR38 globe (not supplied). Please include the rubber gasket supplied. 6. Loosen all lock nuts and screws on lamp-holders before making any adjustments. Please do not loosen the joints more than necessary to disengage the meshing teeth or the internal wiring may be damaged. 7. Turn on power and enjoy your new lighting product. TIPS: 1. To avoid injury or damage to the fitting, ensure that power leads and screws are secure before connecting the power. 2. Handle the fitting with care to avoid breakage. 3. When changing or cleaning bulbs, turn the power OFF and allow to cool. Do not touch bulbs with bare hands, use gloves or a tissue.
3 4. When adjusting lamp holders, ensure that PAR38 globes are not touching or are in close proximity to the sensor head. The heat from the PAR38 globes may distort the sensor unit. 5. Find a suitable location away from liquids and hazards. 6. Ensure that the fitting does not come in contact with corrosive chemicals, etc. 7. To clean, wipe with a damp clean cloth. Never soak the fitting with water. UNDERSTANDING THE CONTROLS (Referring to Fig. 3): ADJUSTING THE TIME DURATION The length of time that the light remains switched on after activation can be adjusted from approximately ten seconds to four minutes. Rotating the TIME control anti-clockwise will reduce the duration time. Note: Once the light has been triggered by the PIR sensor any subsequent detection will start the timed period again from the beginning. ADJUSTING THE LUX CONTROL LEVEL: The lux control module has a built-in sensing device (photocell) that detects daylight and darkness. Rotating the LUX control anti-clockwise is from light ( ) to dark ( ). The ( ) position denotes that the flood lights can work at day and night, and the ( ) position only work at night. You can set to operate the unit at the desired level by adjusting the LUX control. ADJUSTING THE SENSITIVITY: The sensitivity means the max distance which the PIR sensor can be triggered. Turn the SENS control clockwise to increase sensitivity and anti-clockwise to reduce it. SETTING THE CONTROLS: 1. Put the LUX control to light ( ) position, turn the wall switch on and wait half a minute for the control circuit to stabilize. At this stage ensure that the TIME control is set at minimum duration time (rotating the TIME control anti-clockwise to stop-position). The security light will now switch on and remain on for about 30 seconds ( within 60 seconds) 2. Direct the sensor toward the desired area to be scanned by adjusting the elbow joint and swivel joint on the sensor arm. Important: loosen all lock nuts and screws on sensor and lamp holders before making any
4 adjustments, failure to do so could cause damage to the fitting. 3. Have another person move across the centre of the area to be scanned and slowly adjust the angle of the sensor arm until the unit sensors the presence of the moving person, causing the flood lights to switch on ( refer Fig. 1B & Fig. 1C) Note: The sensor will work much more effectively if the item you want detected is passing across the sensor beams, rather than heading directly towards the sensor. 4. Adjust time control to required setting. 5. To set the light level at which the flood lights will automatically switch on at night, turn the LUX control from daylight to night. If the flood lights are required to switch on earlier, e.g. dusk, wait for the desired light level, then slowly turn the LUX control towards daylight symbol while someone walks across the centre of the area to be detected, when the flood light switch is on, release the LUX control. You may need to make further adjustments to achieve your ideal light level setting. HOW TO CHANGE MANUAL CONTROL MODE: 1. When the power is on, the PIR sensor enters into the WARM-UP periods for about 1 minute, then automatically change into AUTO MODE. 2. During AUTO MODE, by switching the installed light switch OFF then ON again within 4 seconds will automatically change the sensor into MANUAL MODE from AUTO MODE. In MANUAL MODE, the flood lights will remain ON, and will not be affected by duration time and LUX control level. 3. To reset back to AUTO MODE, turn the light switch off for at least 10 seconds. Important: To avoid dust build-up and ensure proper functioning of the security light, wipe the sensor lens
5 lightly with a damp cloth every 3 months. Never attempt to modify the unit, there are no user serviceable parts inside. Any attempt to modify the fitting will void the warranty. SPECIFICATIONS: SKU # RATED VOLTAGE LAMP HOLDER RATED WATTAGE V~50Hz E27 2x Max. 150W V~50Hz E27 2x Max. 150W 1. Detection range: Max 12 meters at 180º scan 2. Duration time adjustment: Approximately ten seconds to four minutes. TROULBE SHOOTING AND USER HINTS: PROBLEM POSSIBLE CAUSE SUGGESTED REMEDY Light does not switch on when there is movement in the detection area Light switchs on for no apparent reason ( false trigger) Light remains on Light switches on during daylight hours When setting controls in daylight, the detection distance becomes shorter 1. No mains voltage Check all connections, and fuses/switches 2. Globe(s) faulty or missing Check and replace 3. Nearby lighting is too bright Redirect sensor or relocate the unit 4. Controls set incorrectly Readjust sensor angle or control knob 5. Sensor positioned in wrong direction Redirect sensor and/or adjust Adjust lamp holders to allow a minimum 1. Heat from globe activation sensor gap of 40mm between PAR38 globe and sensor head. 2. Heat sources such as air-con, vents, heater flues, barbecues, other outside lighting, moving cars are activating sensor 3. animals/birds e.g. possums or domestic animals 4. Interference from on/off switching of electric fans or lights on the same circuit as your security flood light. (This problem does not always occur, but a faulty switch or noisy fluorescent light may cause the security floodlight to switch on) Adjust direction of sensor head away from these sources Redirecting sensor head or sensitivity level may help Should the false triggering become, troublesome, consider: (a) Replacing a faulty switch (b) Replacing noisy fluorescent tubes and/or starters (c) Connecting the security flood lights to seperate circuit ( in most cases where one or more of the above suggestions have been carried out, false triggering has been reduced) 5. Refection from swimming pool, or reflective surface. Redirect sensor 1. Continuously false triggered Redirecting sensor head may help 2. Time is set too long Reduce time 1. LUX control knob is set to daylight Turn the LUX control knob to desired light position level setting 1. Interference by sunlight Re-set at night
PARTS INCLUDED TOOLS & PARTS NEEDED Do not mount on vibrating surfaces. appro to 2.5 meters 12M
Type: RH60B-LED Ref: 86524 The bulkhead light incorporates a PIR (Passive Infra Red) sensing device which continuously scans a preset operating zone and immediately switches the lamp on when it detects
More informationDatasheet ENGLISH Halogen lamp 120W with motion sensor ( ) Halogen lamp 400W with motion sensor ( )
Datasheet Halogen lamp 120W with motion sensor (791-8264) Halogen lamp 400W with motion sensor (791-8273) Attention: Please read the following instructions carefully to ensure that mounting operation will
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS
T0436 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local
More information3000W multi Pir light controller
3000W multi Pir light controller Cat No. MLB3000 - Black Cat No. MLW3000 - White Installation & Operating Instructions INSTALLATION & operating instructions SECTION ONE GENERAL INFORMATION The unit utilises
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS
T0103 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local
More information3000W MULTI PIR LIGHT CONTROLLER
3000W MULTI PIR LIGHT CONTROLLER Cat No. MLB3000 Black Cat No. MLW3000 White Installation & Operating Instructions INSTALLATION & OPERATING INSTRUCTIONS E G Dusk/Dawn Time Override/Holiday Mode F H Lens
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS
T0412 / T0413 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS. Hardware
More informationMini Sensor. Outdoor Motion Sensor. Installation Manual
Mini Sensor Outdoor Motion Sensor Installation Manual 1 Contents: Why RAB Sensors are BEST for You? Smaller is better! Mini Sensor uses state-of-the-art surface mount technology (SMT), just like cellular
More informationSTL200/277 Installation Manual STL200/277
STEALTH STL200/277 Installation Manual STL200/277 Specifications: Switching Capacity: Voltage: Detection Pattern: Time Adjustment: Power Consumption: Surge Protection: 8 amps 277 volts 1000 watts incandescent
More informationSTL200/277 Installation Manual STL200/277
STEALTH STL200/277 Installation Manual STL200/277 Specifications: Switching Capacity: Voltage: Detection Pattern: Time Adjustment: Power Consumption: Surge Protection: 8 amps 277 volts 1000 watts incandescent
More informationSTEALTH. STL200 Installation Manual. Specifications: STL200 STL200H STL200HB. Switching Capacity: 8 amps
STEALTH STL200 Installation Manual STL200 STL200HB STL200H Specifications: Switching Capacity: 8 amps Voltage: 120 volts 1000 watts Incandescent 500 watts Fluorescent Detection Pattern: 50 x 200 Time Adjustment:
More information18W Nightsensor Bulkhead
18W Nightsensor Bulkhead Cat No. ECO18P instructions Instructions A Retaining clip B Vertical location Sensor Horizontal location Sensor Wall fixing hole C Wall fixing hole D Wall fixing hole Sensor Vertical
More informationSTEALTH. STL110 Installation Manual. Specifications: STL110 STL110HB STL110H STL110R. Switching Capacity:
STEALTH STL110 Installation Manual STL110 STL110H STL110HB STL110R Specifications: Switching Capacity: Voltage: Detection Pattern: Time Adjustment: Power Consumption: Surge protection: UL Listing: 8 amps
More informationQUANTUM Qflash T2 / X2 OPERATING INSTRUCTIONS
QUANTUM Qflash T2 / X2 OPERATING INSTRUCTIONS 1.0 DESIGNATIONS T2 AND X2 1. Removable Reflector, two positions Normal and Wide angle. 2. Flash-tube 2A. Modeling Lamp (for Model X2 only) 3. Bounce Head,
More informationInstallation Manual. Specifications: Cautions: TURN OFF ALL POWER AT CIRCUIT BREAKER / FUSE PANEL.
Specifications: Installation Manual The STEALTH360 is the most reliable and technically advanced motion-activated light control ever produced. This technical manual is written for electrical professionals
More informationTuff Dome. Installation Manual. vandal resistant. Outdoor Motion Sensor. Contents. Specifications. Switching Capacity:
Tuff Dome Vandal Resistant Outdoor Motion Sensor Installation Manual Contents It s easy to add vandal resistant motion detection to outdoor lights! Specifications Switching Capacity: Relay On/Off Model:
More informationTABLE OF CONTENTS. Safety notes i. Care and Maintenance. ii. 1. Components Illustration Installation of Components.. 4
TABLE OF CONTENTS Safety notes i Care and Maintenance. ii 1. Components Illustration... 1 2. Installation of Components.. 4 2.1 Installation Diagram... 4 2.2 Installation Procedures 5 3. Operation...11
More informationSmart Task Motion Activated Task Light Installation Manual
Smart Task Installation Manual STASK24 STASK21 STASK12 1 SENSOR SPECIFICATIONS: Voltage: 120 Volts AC, 60Hz UL Listing: For Indoor applications Time Adjustment: 5 seconds to 15 minutes Sensor Construction:
More informationWoven Leather Chandelier Large Assembly and Installation Instructions
CAUTION: Woven Leather Chandelier Large Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY
More informationUser Manual. Digital Compound Binocular LED Microscope. MicroscopeNet.com
User Manual Digital Compound Binocular LED Microscope Model MD82ES10 MicroscopeNet.com Table of Contents i. Caution... 1 ii. Care and Maintenance... 2 1. Components Illustration... 3 2. Installation...
More informationSmart Post RAB. Installation Manual. Outdoor Motion Sensor. It s easy to add. motion detection to your post lantern! Contents.
Smart Post Outdoor Motion Sensor Installation Manual Contents Specifications 180º coverage 360º coverage SPOST500/180 SPOST180HL/180 It s easy to add motion detection to your post lantern! SPOST500 SPOST180HL
More informationFFLED18 INSTALLATION INSTRUCTIONS
FFLED18 INSTALLATION INSTRUCTIONS Thank you for buying RC lighting fixtures. Our goal is to design the best quality products to get the job done right. We d like to hear your comments. Call the Marketing
More informationTube Facing Tool.
www.swagelok.com Tube Facing Tool This manual contains important information for the safe and effective operation of the Swagelok TF72 series tube facing tool. Users should read and understand its contents
More informationUser instructions Compound laboratory microscope
KERN & Sohn GmbH Ziegelei 1 D-72336 Balingen E-mail: info@kern-sohn.com User instructions Compound laboratory microscope Tel: +49-[0]7433-9933-0 Fax: +49-[0]7433-9933-149 Internet: www.kern-sohn.com KERN
More informationimpact VC-500LR Monolight INSTRUCTIONS
impact lighting equipment and accessories VC-500LR Monolight INSTRUCTIONS Congratulations on your purchase of the Impact VC-500LR Monolight. We feel that it will contribute much to your photographic skill
More informationSmartBox RAB. Installation Manual. Outdoor Motion Sensor. It s easy to add. motion detection to all your outdoor lights! Contents.
SmartBox Outdoor Motion Sensor Installation Manual Contents It s easy to add motion detection to all your outdoor lights! RAB Specifications Switching Capacity: Relay On/Off Model: 500 watts Incandescent
More informationGLASS GLOBE MOBILE 6-ARM CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [6] (E) Screws [4] (F) Nut [1] (G) Extension rods [3] (H) Transformer [1] (I) Arm counterweights [6] (J) 1.6W LED
More informationInstallation Instructions
TECH SUPPORT The Watt Stopper, Inc. 2800 De La Cruz Blvd. Santa Clara, CA 95050, USA Tel: 1(800)879-8585 1(972)578-1699 Fax: 1(972)422-1311 www.wattstopper.com Outdoor 180 & 270 PIR Motion s Model#s: EW-100-120
More informationGLASS GLOBE MOBILE LINEAR CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [7] (E) Screws [6] (F) Nuts [5] (G) Extension rods [15] (H) Transformer [1] (I) Threaded inserts [5] (J) 1.6W LED
More informationNash Chandelier Assembly and Installation Instructions
CAUTION: Nash Chandelier Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. Important
More informationFFLED18 INSTALLATION INSTRUCTIONS
FFLED18 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We d like to hear your comments. Call the Marketing
More informationDialight Daylight Harvesting Sensor User Guide
Daylight Harvesting Sensor Dialight Daylight Harvesting Sensor User Guide Dialight Catalog Number: DLHU124UG2 1 Safety Instructions Dialight Daylight Harvester Sensor (DLH) User Guide READ AND FOLLOW ALL
More informationModel R8001. Instructionn Manual. Laser Distance Meter. reedinstruments. www. com
Model R8001 Laser Distance Meter Instructionn Manual reedinstruments com Table of Contents Safety... 3 Features... 3 Specifications...3-4 Instrument Description... 5 Operating Instructions...6-10 Measuring
More informationFrom.
From www.illuminated-mirrors.uk.com INSTRUCTION MANUAL 1 1200mm Wide Demister Cabinets (Model Numbers: 100877K124 & K126) Thank you for purchasing our illuminated mirror cabinet(s). To avoid product damage,
More informationUSER'S GUIDE. EcoQuest International 310 T. Elmer Cox Drive Greeneville, TN (423) Setup. Operation. Specifications.
USER'S GUIDE Setup Operation Specifications Warranty (43) 638-746 CAUTION: Read manual carefully for proper procedures and operation. CONTENTS SPECIFICATIONS Specifications...............................................................3
More informationHP 2 SERIES Integral Driver - Solid State LED
HP 2 SERIES Installation Instructions Warning High Voltage Hot Surface NEEDED FOR INSTALLATION: By Others 1/8 & 5/32 Allen Wrench Waterproof Wire Connectors Level Phillips Screwdriver IMPORTANT - WEAR
More informationAutomatic-switch (1,10m): Standard attachment Order No.: Automatic-switch (2,20m): Standard attachment Order No.:
(1,10m): Standard attachment Order No.: 0832.. Comfort attachment Order No.: 0833.. System attachment Order No.: 0842.. (2,20m): Standard attachment Order No.: 0839.. Comfort attachment Order No.: 0838..
More informationHigh Intensity LED Stroboscope Digital Tachometer DT-361/365. Instruction manual. Be sure to read before use.
98585A High Intensity LED Stroboscope Digital Tachometer DT-361/365 Instruction manual Be sure to read before use. Before use, please carefully read these safety precautions as well as instructions, and
More informationPORTABLE HALOGEN WORK LIGHT OWNER S MANUAL
PORTABLE HALOGEN WORK LIGHT OWNER S MANUAL L-9001 (29278) L-9002 (29276) WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules
More informationCX-100. Installation Instructions. PIR Occupancy Sensor SPECIFICATIONS
SPECIFICATIONS CX-1 PIR Occupancy Sensor Voltage... 24VDC Current Consumption... 19mA* Power Supply... WattStopper Power Pack Isolated Relay Rating... 1A@24VDC Time Adjustment... 15 seconds 3 minutes Sensitivity
More informationCAUTION: BEFORE INSTALLING THE LUMINAIRE, MAKE SURE THAT THE CURRENT IS CUT TO THE BOX FUSES / MAIN CIRCUIT BREAKER.
Hanging lamp with horn Assembly and installation instructions CAUTION: BEFORE INSTALLING THE LUMINAIRE, MAKE SURE THAT THE CURRENT IS CUT TO THE BOX FUSES / MAIN CIRCUIT BREAKER. Important safety instructions:
More informationThe wick in your heater needs replacing if, after repeated cleanings, any of the following conditions still exist:
WICK REPLACEMENT The wick in your heater needs replacing if, after repeated cleanings, any of the following conditions still exist: Slow to light, hard movement of the wick adjuster knob, kerosene odor
More informationMD9300 Metal Detector OWNER S MANUAL
Famous Trails Anaheim, California Phone (714) 701-9671 Fax (714) 701-9672 Toll Free: (877) 97SCOPE www.famoustrails.com MD9300 Metal Detector OWNER S MANUAL CONTENTS Assembling the Detector----------------------------------------------------------
More informationHIGH/LOW/OFF PIR OUTDOOR PHOTO/MOTION SENSOR IN IP66 ENCLOSURE WITH BLUETOOTH
HIGH/LOW/OFF PIR OUTDOOR PHOTO/MOTION SENSOR IN IP66 ENCLOSURE WITH BLUETOOTH Product Overview The FSP-3x1B is a family of passive infrared (PIR) outdoor sensors that raise or lower the electric lighting
More informationFabric tiered drum pendant 30in Assembly and Installation Instructions
CAUTION: Fabric tiered drum pendant 30in Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY
More informationlighting your creativity HONEY BADGER 320Ws Digital Flash Instruction Manual
lighting your creativity HONEY BADGER 320Ws Digital Flash Instruction Manual www.interfitphotographic.com Honey Badger 320 Digital Flash What s cool about the Honey Badger? The Honey Badger is the perfect
More informationCleaning the cutter blade
Cleaning the cutter blade < Daily maintenance > In order to use this printer in good condition, please perform the daily maintenance. Note the following when performing the maintenance. Do not lubricate
More informationInstallation Manual. The STEALTH 360 is the most reliable and technically advanced motionactivated
Installation Manual The STEALTH 360 is the most reliable and technically advanced motionactivated light control ever produced. This technical manual is written for electrical professionals who wish to
More informationINSTRUCTION MANUAL INF Fax: (503)
INSTRUCTION MANUAL INF151 1-800-547-5740 Fax: (503) 643-6322 www.ueiautomotive.com email: info@ueitest.com Introduction Congratulations on your purchase of the INF151 infrared thermometer. Like all UEi
More informationInstalling the FSP-211 Sensor in Light Fixture
(grey) WATTSTOPPER VOLTAGE HIGH/LOW/OFF PIR FIXTURE INTEGRATED OUTDOOR PHOTO/MOTION SENSOR Product Overview The is a passive infrared (PIR) outdoor sensor that raises or lowers the electric lighting level
More informationQUANTUM Qflash MODEL T OPERATING INSTRUCTIONS
QUANTUM Qflash MODEL T OPERATING INSTRUCTIONS 1.0 DESIGNATIONS 1. Removable Reflector, two positions Normal and Wide angle. 2. Flash-tube 3. Bounce Head, Rotates 180º 4. Swivel Head, Rotates ± 90º 5. Sensor
More informationUser Manual. Trinocular Metallurgical Microscope. MicroscopeNet.com
User Manual Trinocular Metallurgical Microscope Model M83MPTR MicroscopeNet.com Table of Contents i. Caution.. 1 ii. Care and Maintenance... 2 1. Components Illustration..... 3 2. Installation...4 3. Operation
More informationModel:CB-MRC. Instruction Manual of Mini Recessed Motorized Screen
GRANDVIEW REPRODUCING GENUINE COLORS GRANDVIEW REPRODUCING GENUINE COLORS Instruction Manual of Mini Recessed Motorized Screen Grandview Crystal Screen Canada Ltd. #11-3751 North Fraser Way, Marine Way
More informationIR-3000 Wireless PIR Sensor. Owner s Manual
IR-3000 Wireless PIR Sensor Owner s Manual Warnings This device complies with Part 15 of the FCC rules, Operation of this device is subject to the following conditions: 1. This device may not cause harmful
More informationEBDSM-PRM Product Guide
EBDSM-PRM Product Guide Ceiling PIR presence/absence detector Overview The EBDSM-PRM PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual control.
More informationCustom Pendant- Hardwire Assembly and Installation Instructions
Custom Pendant- Hardwire Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationInstallation Manual. The STEALTH 360 is the most reliable and technically advanced motionactivated
Installation Manual The STEALTH 360 is the most reliable and technically advanced motionactivated light control ever produced. This technical manual is written for electrical professionals who wish to
More informationInstallation Manual. Specifications: Cautions: Switching Capacity: 360º below and to the sides
Specifications: Installation Manual The STEALTH 360 is the most reliable and technically advanced motionactivated light control ever produced. This technical manual is written for electrical professionals
More informationThe Interfit S1. AC/DC Powered TTL/HSS Flash. Instruction Manual.
The Interfit S1 AC/DC Powered TTL/HSS Flash Instruction Manual www.interfitphotographic.com Interfit S1 Battery Powered TTL/HSS Flash Unit What s cool about the Interfit S1? The S1 is the world s first
More informationAH Auto-Darkening Welding Helmet User Manual. Made in China
AH7-220-0000 Auto-Darkening Welding Helmet User Manual Made in China 2016 TECHNICAL SPECIFICATIONS AH7-220-0000 Auto-Darkening Welding Helmet 2016 WARNING Please read all instructions before using the
More informationTRANSFORMER HD-HAMPTON HAMPTONBAY.COM
Item #1001 510 115 Model DIY-600PS USE AND CARE GUIDE TRANSFORMER Questions, problems, missing parts? Before returning to the store, call HamptonBay Customer Service 8 a.m. - 7 p.m., EST, Monday Friday,
More informationINSTRUCTION MANUAL. 1 Light Exterior Wall Lantern. Home Depot SKU (UPC ) Home Depot SKU (UPC ) (Prairie Bronze)
INSTRUCTION MANUAL 1 Light Exterior Wall Lantern Home Depot SKU 477405 (UPC 718212230107) Home Depot SKU 495682 (UPC 718212230282) (Prairie Bronze) Page 1 Thank you for purchasing this Hampton Bay exterior
More informationKING CANADA INSTRUCTION MANUAL 10 COMPOUND SLIDING MITER SAW WITH TWIN LASER GUIDE MODEL: 8380
KING CANADA 10 COMPOUND SLIDING MITER SAW WITH TWIN LASER GUIDE *Enhanced Twin Laser Effect MODEL: 8380 INSTRUCTION MANUAL COPYRIGHT 2008 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC. WARRANTY INFORMATION
More informationCONTENTS Preparation Functions and Indications Operation
CONTENTS Features 3 Preparation Parts of the detector 4 Assembling the detector 4 Adjusting the search coil 6 Installing the batteries 6 Using the headphones 7 Functions and Indications Parts of the control
More informationluxcontrol lighting control system basicdim basicdim ILD 16DPI 69f Compact control module with ambient light sensor and motion sensor
ILD 16DPI 69f Compact control module with ambient light sensor and motion sensor Product description Compact dimensions for luminaire installation For up to 10 DSI or LI devices (max. 5 per output channel)
More informationHigh Bay Occupancy Sensor for Use with Electronic Ballast HID Luminaires
Instruction Bulletin 63249-500-08A6 05/2011 High Bay Occupancy Sensor for Use with Electronic Ballast HID Luminaires SLSPIP210EB and SLSPIP210EBCT INTRODUCTION Figure 1: High Bay Occupancy Sensor for Use
More informationTop spin Nr /
Top spin Nr. 1840 0000 / 1840 1000 Bedienungsanleitung 21-6680 28052014 / A Made in Germany Ideas for dental technology Top spin Nr. 1840 0000 / 1840 1000 Contents 1. Introduction...2 1.1 Symbols...2 2.
More informationAssembly & Installation Instructions
1 OF 6 Component Parts A Fixture Pipe (3) B Coupling (3) C Canopy Pipe (3) D Middle Canopy Can E Clutch (3) F Plastic Sleeve (3) G Side Canopy Can (2) H Set Screw (3) I Middle Crossbar J #10 Screws (4)
More informationLazerTape 160. Lazer Distance Meter TRIPLETT. Instruction Manual. 99 Washington Street Melrose, MA Phone Toll Free
TRIPLETT - - - -- - - - - -- - - - -- - --- - -- LazerTape 160 Lazer Distance Meter Instruction Manual 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com
More informationInstruction Manual. Compact Studio Flash
Instruction Manual Compact Studio Flash FOREWORD Thanks for choosing LUMI series studio flash. It is a durable and good quality strobe with complete functions to help photographers create desired lighting
More informationUser instructions Compound laboratory microscope
KERN & Sohn GmbH Ziegelei 1 D-72336 Balingen E-mail: info@kern-sohn.com User instructions Compound laboratory microscope Tel: +49-[0]7433-9933-0 Fax: +49-[0]7433-9933-149 Internet: www.kern-sohn.com KERN
More informationArched Top Lantern Pendant Assembly and Installation Instructions. Country of Destination: US/CN UK/EU/AUS Middle East
CAUTION: Arched Top Lantern Pendant Assembly and Installation Instructions Country of Destination: US/CN UK/EU/AUS Middle East BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF
More informationCONTENTS OF THE BOX. *PIR sensor only **Dual Technology and PIR sensors only. Description PIR Ultrasonic Dual Technology
Instruction Bulletin 63249-420-283A4 08/2009 Wall Mount Occupancy Sensor SLSWPS1500, SLSWUS1500, SLSWDS1500 INTRODUCTION Wall Mounted Occupancy Sensors are Class 2 devices ideal for use in business or
More informationSMARTBULLET SMSBULLET2X12
SMARTBULLET SMSBULLET2X12 Installation Manual 1 Contents: SMSBULLET2X12 Why RAB Sensors are BEST for You? Wire Nuts (3) Smaller is better! Mini Sensor uses state-of-the-art surface mount technology (SMT),
More informationUse timers, motion detectors, remote controls, and photocells to reduce waste.
Exterior Exterior luminaires include large-area flood and small-area, landscape, and accent luminaires. They illuminate building facades, pathways, and landscapes and can provide lighting for safety, security,
More informationWireless Occupancy Sensor User Guide
Wireless Occupancy Sensor Wireless Occupancy Sensor User Guide This Manual covers both the Wide angle and the Narrow long range occupancy sensor. Dialight Part Numbers described here-in are: WOSU22BG2
More informationFBX-PA-2AC. Third edition : April No
FBX-PA-2AC Third edition : April 2006 No. 060058 INTRODUCTION Thank you very much for purchasing Kansai Special FBX series. Read and study this Instruction Manual carefully before you start any of the
More informationMAXIMIST HVLP TANNING SYSTEM
L0941 12 10:Layout 1 16/12/10 09:03 Page 1 MAXIMIST HVLP TANNING SYSTEM DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL This manual contains important warnings and instructions. Please read these instructions
More informationEBDSPIR-AT-DD. RF ceiling PIR presence detector DALI / DSI dimming. Product Guide. Overview. Features
Product Guide EBDSPIR-AT-DD RF ceiling PIR presence detector DALI / DSI dimming Overview The EBDSPIR-AT-DD is a passive infrared (PIR) motion sensor combined with two output channels capable of controlling
More informationGENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
More informationSmartBox. Outdoor Motion Sensor. Installation Manual
SmartBox Outdoor Motion Sensor Installation Manual 1 Contents: Smart Box Why RAB Sensors are BEST for You? Mounting Screws (3) Lens Mask Smaller is better! SmartBox uses state-of-the-art surface mount
More informationML7520 ML7530 DIOPTER ADJUSTMENT RING BINOCULAR BODY, INCLINED 30. (a) Field Iris Control Lever. (c) Filter Slots EYEPIECES, KHW10X
JAPAN DIOPTER ADJUSTMENT RING BINOCULAR BODY, INCLINED 30 (a) Field Iris Control Lever (c) Filter Slots EYEPIECES, KHW10X ANALYZER CONTROL LEVER (b) Aperture Iris Control Lever LIGHT SOURCE HOUSING VERTICAL
More informationA524 ASSEMBLY & INSTALLATION INSTRUCTIONS BELLADONNA PENDANT CASTLETON, VERMONT USA SYNCHRONICITYLIGHTING.COM Rev A 1 OF 7
1 OF 7 COMPONENT PARTS A B Canopy Mounting Bracket C Anchor (4) D #10 Wood Screw (4) E F G H Safety Cable Ground Screw Cupped Washer Safety Cable screw I Gripper (2) J Barrel Knob (4) K L Lightbar Fixture
More informationROLLER STAND WITH TWO-LEG SUPPORT ASSEMBLY AND OPERATING INSTRUCTIONS
ROLLER STAND WITH TWO-LEG SUPPORT 95621 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2006 by Harbor Freight
More informationCHAINSAW SHARPENER MODEL: ECSS-1
CHAINSAW SHARPENER MODEL: ECSS-1 Part No: 3402075 ASSEMBLY & INSTRUCTION MANUAL LS0409 INTRODUCTION Thank you for purchasing this CLARKE product Before attempting to use the product, it is essential that
More informationOperating Manual. Model 721N. Visible Spectrophotometer
Operating Manual of Model 721N Visible Spectrophotometer 1 Table of Contents 1. Chief uses... 3 2. Working Conditions... 3 3. Main Specifications...3 4.Operating Principles...4 5. Optical design...4 6.
More informationSTEINDORFF METALLURGICAL MICROSCOPE. NYMCS-620 Instruction Manual
METALLURGICAL MICROSCOPE NYMCS-620 Instruction Manual It is recommended strongly that you study this manual thoroughly before using the microscope. Retain this manual in an easily accessible place near
More informationTreasure Cove Metal Detector
Treasure Cove Metal Detector Fortune Finder 1023 OWNER S MANUAL www.treasure-cove.com 805-658-2328 With your 1023 metal detector, you can hunt for coins, relics, jewelry, gold, and silver just about anywhere,
More informationZoom Stereo Microscope NYMCS-360 Instruction Manual
Zoom Stereo Microscope NYMCS-60 Instruction Manual This manual is written for stereo microscope NYMCS-60. To ensure the safety, obtain optimum performance and to familiarize yourself fully with the use
More informationHIGH/LOW/OFF PIR OUTDOOR PHOTO/MOTION SENSOR IN IP66 ENCLOSURE FOR FLEXIBLE MOUNTING
HIGH/LOW/OFF PIR OUTDOOR PHOTO/MOTION SENSOR IN IP66 ENCLOSURE FOR FLEXIBLE MOUNTING Product Overview The FSP-2x1B is a family of passive infrared (PIR) outdoor sensors that raise or lower the electric
More informationINSTRUCTIONS FOR ASSEMBLY AND OPERATION OF ERMA MICROTOME
OPERATING MANUAL, ERMA RADIAL INSTRUCTIONS FOR ASSEMBLY AND OPERATION OF ERMA MICROTOME Upon receipt of your Erma Microtome please check the contents of the packages (s). These are itemized below: 1. Microtome
More informationThanks for shopping with Improvements! 7 ft. Wall Christmas Tree w/ Stand Item #419359
Thanks for shopping with Improvements! 7 ft. Wall Christmas Tree w/ Stand Item #419359 IMPORTANT: RETAIN FOR FUTURE REFERENCE. READ CAREFULLY. PARTS LIST: NOTES: (1) Tree Section A (1) Tree Section B (1)
More informationMUTO COMFORT XL 150 L 80
MUTO COMFORT XL 150 L 80 Installation instructions - Ceiling mount [less DORMOTION] ( door) TABLE OF CONTENTS Overview Intended use Ceiling requirements and fittings Requirements for glass panel Safety
More informationMAKING SENSE OF SLIT LAMP SERVICING
MAKING SENSE OF SLIT LAMP SERVICING HOW TO LOOK AFTER AND CARE FOR A SLIT LAMP The slit lamp is an essential and oftenused diagnostic instrument in ophthalmology. It provides illumination and magnification
More informationRabbit Series Laser Engraving Machine HX3040. User s Manual. 1 Jinan King Rabbit Technology Development Co. Ltd.
Rabbit Laser Engraving Machine HX3040 User s Manual 1 Preface Thank you for buying our Rabbit Series HX3040 Laser Engraving Machine. You will find it has many nice features including easy operation, high
More informationSteele TV Stand Stock # BH
LOT NUMBER: DATE PURCHASED: / / Steele TV Stand Stock # BH46-084-899-02 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store
More informationMANUAL EXC-350 MICROSCOPE SERIES
MANUAL EXC-50 MICROSCOPE SERIES 7 Mall Drive, Commack, NY 75 6-864-000 (P) 6-54-8900 (F) www.accu-scope.com info@accu-scope.com CONTENTS SAFETY NOTES... CARE AND MAINTENANCE... INTRODUCTION... 4 UNPACKING
More informationMultipurpose Overbed Table
Multipurpose Overbed Table User s Guide AFTER SALES SUPPORT USA (800) 407 458 ITEM #44576 Contents 0 Introduction Intended use p. 04 NOTE Pay attention to important information and notes when reading the
More information1: White buttons Used by the user on a daily basis. 2: Grey buttons Used only upon first startup.
Fig. 1 Lock/ unlock 30 1000 Light 1 100 300 zone 1 Learn actual lux LED 600 2000 0,4 0,6 0,8 1,0 1,2 Time 1 Light 2 zone 2 1,4 1,6 Factor of lux zone 1 Pulse 2min 5min Time Time 2 10min 15min 30min 1 2
More informationInstallation Manual Porter Road, Sarasota FL fax
072015 Installation Manual BEFORE YOU BEGIN: Read these instructions completely and carefully. FOR YOUR SAFETY: Read and observe all CAUTIONS and WARNINGS shown throughout these instructions. Risk of injury.
More information