OLED-55 USER MANUAL OCTALUX LED. OctaLux LED - USER MANUAL 1

Transcription

1 OLED-55 OCTALUX LED USER MANUAL OctaLux LED - USER MANUAL 1

2 OctaLux LED INTRODUCTION Thank you for choosing Genaray. The OctaLux LED Light Softbox produces bright, soft, and consistent light that s designed for use in the studio or on location when shooting portraits, beauty/fashion, tabletop products, and interviews. 240 individual LEDs generate a 5500 K daylight-balanced light that creates warmth and glow on your subject. This continuous light emits very little heat, so it can be used for extended periods without overheating, and it allows you to get up close for intimate shots. A dimmer control affords the ability to change the light output from 10% to 100%.This is a great feature when environment conditions alter the amount of light needed for proper exposure. 2 OctaLux LED - USER MANUAL

3 TABLE OF CONTENTS Introduction The housing is sturdy, and the LEDs are not prone to breakage like fluorescent fixtures, making the Genaray OLED-55 ideal for everyday usage. The OctaLux LED Light Softbox is 31.5 (80 cm) in diameter, and it attaches with tension rods to the integrated speed ring, making setup a snap. Additionally, you have the option of three diffusion attachments. The diffusers help soften the light output, which is more flattering and minimizes harsh shadows. Precautions Overview Assembling the Softbox Attaching the Diffusers Mounting the OctaLux...14 Powering the OctaLux...15 Disassembling the Softbox...16 Specifications...17 Warranty...19 OctaLux LED - USER MANUAL

4 PRECAUTIONS PRECAUTIONS Please read and follow these instructions, and keep this manual in a safe place. Keep this product away from water and any flammable gases or liquids. Do not leave the device in a closed vehicle under the sun or in other areas subject to very high temperatures. Make sure this product is powered off when plugging it into a power source. Always remove the power cord by holding the plug; do not pull the cord. Disconnect the power cord from the power supply when not in use. Use only the correct, recommended voltage. Do not attempt to disassemble or repair this product. There are components inside that can produce a hazardous electric shock. 4 OctaLux LED - USER MANUAL

5 Do not stare at the light when it is powered on. Do not point directly towards the naked eye (especially those of infants and small children) it may lead to visual impairment. Avoid any unnecessary impact to the unit, as this can damage the LEDs. Handle this product with care. Do not touch the LEDs or expose them to moisture. If necessary, clean the LEDs with only a lint-free, cotton cloth. Do not smudge. Keep this product away from children. Make sure that this product is intact and that there are no missing parts. All images are for illustrative purposes only. PRECAUTIONS OctaLux LED - USER MANUAL 5

6 Reflector dish OctaLux light head PRODUCT OVERVIEW LEDs Tilt-adjustment knob Locking knob Diffuser cap 120 V AC/DC power adapter AC power cable 6 OctaLux LED - USER MANUAL

7 Integrated speed ring Handle socket PRODUCT OVERVIEW On/off dimmer knob DC power input socket Front diffuser Mounting socket OctaLux LED - USER MANUAL 7

8 Inner diffuser Side A PRODUCT OVERVIEW Softbox tension-rod pockets Internal diffuser ringlets 8 tension rods Side B 8 OctaLux LED - USER MANUAL

9 Touch-fastener strips 31.5 (80 cm) OctaLux softbox PRODUCT OVERVIEW Access flaps Spacer OctaLux light-head handle OctaLux LED - USER MANUAL 9

10 ASSEMBLING THE SOFTBOX INSTRUCTIONS 1. Place the OctaLux light head faceup on a flat surface 2. Open the access flaps on the back of the OctaLux softbox, place the softbox around the light head. It will take shape with the following steps. 3. Insert the first tension rod (side B) in any of the eight pockets at the outer edge of the OctaLux softbox. 4. Insert the other end of the tension rod (side A) into the speed-ring socket on the side of the light head. 5. Insert the next rod at the opposite side (180 ) of the first rod. Insert one end into the correct pocket on the softbox, and then insert the other end into the corresponding speed-ring socket. 10 OctaLux LED - USER MANUAL

11 6. Insert the next two rods at a 90 angle from the first two rods that were inserted. This time insert each additional rod into a socket on the speed ring, and then into a pocket on the softbox. 7. Insert the remaining rods, one opposite the next. Once all rods are in place, the softbox will firm up and take shape. 8. Close the access flaps on the back of the OctaLux softbox to ensure that it fits tightly. This will prevent any light leaks. 9. Insert the OctaLux light-head handle into the handle socket. Rotate clockwise until the handle is fully tightened. INSTRUCTIONS OctaLux LED - USER MANUAL 11

12 ATTACHING THE DIFFUSERS INSTRUCTIONS The diffusers soften the light output and can be used separately or in combination for varying results. 1. Stretch the diffuser cap over the LED light head s built-in reflector dish. 2. Attach the inner diffuser to the ringlets hanging on the inside of the softbox. 12 OctaLux LED - USER MANUAL

13 3. Stretch the front diffuser over the outside edge of the softbox, aligning the touch-fastener strips. INSTRUCTIONS 4. Press the touch-fastener strips together, and make certain that the diffuser fits tightly on all sides. OctaLux LED - USER MANUAL 13

14 MOUNTING THE OCTALUX The OctaLux mounts to most light stands that have a standard 5/8 stud. INSTRUCTIONS 1. Make sure the tilt adjustment knob is fully tightened. 2. Loosen the locking knob on the mounting socket, and mount the OctaLux LED Light on your light stand. Locking Knob Tilt Adjustment Knob 3. Tighten the locking knob until secure. You can adjust the tilt of the OctaLux LED Light by loosening the tilt adjustment knob. Keep one hand on the light to hold it steady. 14 OctaLux LED - USER MANUAL

15 POWERING THE OCTALUX Make sure the unit is turned off. Connect the AC power cable to the AC/DC adapter and a wall outlet. Connect the adapter s DC connector to the OctaLux light. To turn on the OctaLux light, turn the On/off dimmer control clockwise until you hear a click. INSTRUCTIONS ADJUSTING THE POWER OUTPUT You can adjust the OctaLux s power output from 10% 100%. To adjust power output via the On/off dimmer knob, rotate the knob clockwise. OctaLux LED - USER MANUAL 15

16 DISASSEMBLING THE SOFTBOX INSTRUCTIONS 1. Ensure that the power control on the back of the light head is turned to the Off position. Unplug the power cord from the wall outlet. 2. Unplug the power cord from the back of the light head. 3. Release the light-stand locking knob, and remove the light head from the light stand. 4. Remove the front diffuser. 5. Detach the inner diffuser from the ringlets hanging on the inside of the softbox. 6. Remove the diffuser cap if attached. 7. Remove the OctaLux light-head handle by rotating it counterclockwise until you can separate it from the light head. 8. Open the access flaps on the back of the softbox. 9. Remove a tension rod from the speed ring, and then from the pocket on the opposite end. 10. Remove the rod at the opposite side, and then repeat this process until all rods are removed. 16 OctaLux LED - USER MANUAL

17 PRODUCT SPECIFICATIONS OctaLux LED Light source: 240 LEDs Lamp life: 50,000 hr. 3 1 m: 2000 lx no diffusers 1500 lx with front diffuser only 1800 lx with inner diffuser only 1700 lx with diffuser cap only Power consumption: 55 W Color temperature: 5500 K (±200 K) CRI: 89 Dimming: 10% 100% Softbox diameter: 31.5 (80 cm) AC operating voltage: V, 50/60 Hz Weight: 2.85 lb. (1.3 kg) Dimensions (H W D): ( cm) SPECIFICATIONS OctaLux LED - USER MANUAL 17

18

19 ONE-YEAR LIMITED WARRANTY This Genaray product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. Genaray s responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at Genaray s discretion, of any product that fails during normal use of this product in its intended manner and in its intended environment. Inoperability of the product or part(s) shall be determined by Genaray. If the product has been discontinued, Genaray reserves the right to replace it with a model of equivalent quality and function. This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, GENARAY MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also have additional rights that vary from state to state. To obtain warranty coverage, contact the Genaray Customer Service Department to obtain a return merchandise authorization ( RMA ) number, and return the defective product to Genaray along with the RMA number and proof of purchase. Shipment of the defective product is at the purchaser s own risk and expense. For more information, or to arrange service, visit or contact us at info@genaray.com Genaray LLC. All Rights Reserved.

20 20 OctaLux LED - USER MANUAL GG2