How to solder SMD component on Awesome PCB or any other kind of PCB.
|
|
- Dustin Harris
- 6 years ago
- Views:
Transcription
1 How to solder SMD component on Awesome PCB or any other kind of PCB. Step by step tutorial, with no steps to skip. Step 1 - What do we need? Step 2 - Fixing PCB Step 3 - Preparing for soldering Step 4 Rosin Step 5 - Tin - soldering SMD pad Step 6 - Soldering 1 pad of SMD component Step 7 - Soldering 2 pad of SMD component Step 8 - Placement of the connector Step 9 - Rosin - Soldering of the connector Step 10 - Soldering of the connector Step 11 - Silkscreen on the PCB value of the component Step 12 - Check connections with gauge Step 13 - Assembly PCB in the Bread Board Step 14 - Additional tips 1
2 To make a long story short first of all Awesome PCB allowed you to solder any SMD component in package 0603, 0805, 1206, SOT23, SOT223 and use them on the Bread Board when you are making your prototype. Step 1 What do we need? Awesome PCB or other PCB. SMD component - in our case it will be resistor in package 1206 and value 10k Ohm. Tin - to solder SMD component on the PCB. Resin - to keep clean solder place from contamination. Tweezers - to have a better handle SMD component. Soldering station - to melt tin and solder SMD on the PCB. Insulating adhesive tape - to fix PCB in the one place during soldering of SMD. Gauge - to check result after soldering. Step 2 Fixing PCB Mount PCB on flat surface, stick PCB with tape on the flat surface. 2
3 Step 3 Preparing for soldering Turn on the soldering iron and after the warm-up, soak the tip for 2-3 seconds in the rosin to clean it of impurities. Step 4 Rosin If you are using a soldering iron transformer, leave a drop of rosin on the top of the tip. This will facilitate soldering tin to SMD pad on the PCB in the next step. Step 5 Tin - soldering SMD pad Cover only one pad of SMD 1206 on the PCB with a small amount of tin, which will melts under the influence of soldering tip temperature. Covering one pad will allow us to more easily maintain the correct position SMD component and will allowed correct soldering. Pad will be cover by tin and resin. 3
4 Step 6 Soldering 1 pad of SMD component Grab SMD component with tweezers, in our case resistor in the housing 1206, and value 10K. Place SMD component on the proper pads regarding pictures, and solder pad. Try to keep component symmetrical versus pads on the PCB. If everything was done properly, component should settle on the surface of the PCB on the place dedicated for package
5 Step 7 Soldering 2 pad of SMD component After about 3-4 seconds after the first pad was soldered, proceed to solder 2 pad SMD component. Delay time is needed for staying component on the solder pad. Tin should cool down to avoid unintentional movement of the soldered component. 5
6 Step 8 Placement of the connector Raster of the hole on the Awesome PCB allowed you to place standard connector (straight pin or bent) with pith 0.1inch (2.54mm). Hole diameter is equal 1.1mm wit tolerances +0.1mm. Place connector in the holes like it is presented on the picture. 6
7 Step 9 Rosin - Soldering of the connector This step is similar to Step 3 and Step 4. So if you are using a soldering iron transformer, leave a drop of rosin on the top of the tip. Step 10 Soldering of the connector Solder pins of the connector to the PCB. 7
8 Step 11 Silkscreen on the PCB value of the component On the other side of the PCB there is the dedicated place where you can add value of the component to make a better tracking of it on the Bread Board during prototype phase. Silkscreen can also allow you to store and reuse Awesome PCB in the next future projects. Step 12 Check connections with gauge After all of the taken steps till now last one will be a checking value of the component with the gauge to make sure that everything is fine. Connect pin of the gauge to pin 1 and pin 2 of Awesome PCB and make a settings of the Gauge on proper range of the resistance in case of resistor. In presented example rang of gauge is setted for 20k. If SMD component was properly soldered, around 10k will be presented on the display of the gauge. 8
9 Step 13 Assembly PCB in the Bread Board Now Awesome PCB is ready to be place in your Bread Board or prototype circuit. Step 14 Additional tips To make it more easy soldering SMD components, you could use the copper wire with a reduced diameter. Typically, the diameter of the wire solder is in the range of 2-2.5mm. The diameter of the solder wire, which I used is about 0.5mm. Wire about this range of diameter can be taken from ethernet cable. Please keep in mind that smaller diameter of the wire will heat up faster and it will faster belong degradation compared to wire with higher diameter. You can also mount on the Awesome PCB other type of SMD components instead of listed 0603, 0805, 1206, SOT23, SOT223. 9
DEM ABPM KIT All Band Power Meter Assembly Notes and Pictures
DEM ABPM KIT All Band Power Meter Assembly Notes and Pictures Paul Wade W1GHZ w1ghz@arrl.net Down East Microwave has kindly agreed to make kits available for my All Band Power Meter (Note: I receive no
More informationAssembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
More informationPSU for LawMate 500mW Transmitters. Assembly and Operation Manual
PSU for LawMate 500mW Transmitters Assembly and Operation Manual Introduction Thank you for purchasing LawMate 500mW Power Supply. This power supply was specifically designed for the 500mW LawMate transmitter
More informationElektor Construction Guide TAPIR
Elektor Construction Guide TAPIR The TAPIR is a three-dimensional assembly. To ensure good access to all soldering points, we recommend assembling the kit exactly according to the described sequence. 1
More informationPSU V2 for LawMate 500mW Transmitters. Assembly and Operation Manual
PSU V2 for LawMate 500mW Transmitters Assembly and Operation Manual Introduction Thank you for purchasing the V2 LawMate 500mW Power Supply. This power supply was specifically designed for the 500mW LawMate
More informationInstallation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions)
Installation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions) This tutorial is designed to aid you in installation of a console customs
More informationFM Wireless Microphone Kit Instructions for Assembly Page 1 of 5
Instructions for Assembly Page 1 of 5 1. Find Resistor R1. Remove any tape that may be attached to the leads. Bend the leads as needed to insert Resistor R1 into the printed circuit board in the holes
More informationDDDAC1794. Version 1.1
Finally!! The new, highly improved 2016 module! De voltage regulation at the analog side of the system has now an embedded Tentlabs Shunt regulator. The Bias through the much discussed pin 20 got a constant
More informationArduTouch Music Synthesizer
ArduTouch Music Synthesizer Assembly Instructions rev C Learn To Solder download for free at: http://mightyohm.com/soldercomic The following photos will show you how to solder. But feel free to download
More informationMEGAbitty Micro Line Sensor Board Assembly Instructions 11/15/2003
1 Board Preparation U1 & U2 are mounted upside down, protruding through the board. That is, when the board is viewed from the top, the lenses should point down. Holes for U1 & U2 need to be cut out. Use
More informationLine Following Circuit Board Wiring Guide
Line Following Circuit Board Wiring Guide Soldering the Analog Optosensors 1. Obtain a line following printed circuit board from the store as well as three analog optosensors (w/6 resistors). 2. Remove
More informationPI & T Attenuators. Version This document is for printed circuit board version 0.0a for both the PI and T attenuators.
PI & T Attenuators Version This document is for printed circuit board version 0.0a for both the PI and T attenuators. Overview & Features: The PI and T attenuators use 0805 resistors and for most values
More informationInstallation tutorial for Console Customs Xbox Mode Dual Button (RFX-5B) Rapid fire Microchip for all Wired and Wireless controllers
Installation tutorial for Console Customs Xbox 360 5-Mode Dual Button (RFX-5B) Rapid fire Microchip for all Wired and Wireless controllers This tutorial is designed to aid you in installation of a console
More informationQRPGuys Iambic Mini Paddle
QRPGuys Iambic Mini Paddle First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use qrpguys.parts@gmail.com
More informationSoldering Application
Soldering Application Eugene Kim EEC 134 Team GrildurFrostcrag!1 I. Introduction Soldering, using fusible metal alloy as an adhesive, played a key role in constructing the quarter two RF radars. It is
More informationSMD-Dummy-BNC Assembly Instructions
This small QRP sized dummyload was designed as a learning tool for SMD soldering by using larger 2512 resistors with only 1 small SOT-23 diode. The 50 ohm load will operate from 500KHz to 30MHz with an
More informationScaleRCHelis.com V Light Controller Kit
Thank you for purchasing the ScaleRCHelis.com V1.1 450 Light Controller Kit. This is something you can build in under a hour with some simple soldering equipment. Your kit will include all the parts necessary
More informationLearn to Solder: Simon Says Stencil Kit Information & Instructions
Learn to Solder: Simon Says Stencil Kit Information & Instructions This is considered an intermediate kit for people who have soldered through-hole components before and wish to learn how to reflow surface
More informationThe Empeg and Riōcar Illumination Kit Installation and User s Manual
The Empeg and Riōcar Illumination Kit Installation and User s Manual Last Updated: October 13, 2005 Table of Contents READ THIS FIRST!!!...1 Introduction to the Installation Process...3 Install the Hijack
More informationLA502 Assembly guide Main PCB Resistors - (2)
LA502 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationAssembly instructions for the CS-1 ChemShield
Page 1 Of 6 Assembly instructions for the CS-1 ChemShield What is S.M.D SMD=Surface mount devices, like all the components does not have leads, but gets soldered onto flat solder pads. The CS-1 assembly
More informationCustom Front Panel Upgrade Instructions
Custom Front Panel Upgrade Instructions Here are the directions for upgrading your SP-II to an SP-IIB, with a custom blackanodized front panel and engraved lettering. There are only forty SP-IIB s in existence
More informationInstallation tutorial for Console Customs PS3 TrueFire Standard Rapid fire Microchip for Sixaxis and Dualshock 3 controllers
Installation tutorial for Console Customs PS3 TrueFire Standard Rapid fire Microchip for Sixaxis and Dualshock 3 controllers This tutorial is designed to aid you in installation of a console customs rapid
More informationSoftRock v5.0 Builder s Notes. December 12, Building a QSD Kit
SoftRock v5.0 Builder s Notes December 12, 2005 Building a QSD Kit Be sure to use a grounded tip soldering iron in building the QSD board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),
More informationAssembly Instructions for the FRB FET FM 70 Watt Amp
Assembly Instructions for the FRB FET FM 70 Watt Amp 1.) Orient the circuit board with the diagram 2.) Use a narrow chisel tip 25-30 watt soldering iron for assembly 3.) All the small parts are taped onto
More informationLighthouse Beginner s soldering kit
Lighthouse Beginner s soldering kit Kit contains: 1 x 220 ohm resistor (Red, Red, Black) 1 x 82k ohm resistor (Grey, Red, Orange) 2 x 220k ohm resistors (Red, Red, Yellow) 2 x Diodes 1 x Power switch 1
More informationSoftRock v6.0 Builder s Notes. May 22, 2006
SoftRock v6.0 Builder s Notes May 22, 2006 Be sure to use a grounded tip soldering iron in building the v6.0 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),
More informationCreating another Printed Circuit Board
Appendix C Creating another Printed Circuit Board In this chapter, we will learn the following to World Class standards: Starting with a Finished Schematic Creating the Layers for the Printed Circuit Board
More informationInstructions for Lighting an S Scale Caboose
Instructions for Lighting an S Scale Caboose The S Scale Caboose lighting kit is adaptable for most caboose models of rolling stock including American Flyer (TM) and contains the same components as found
More informationSoftRock v6.0 Builder s Notes. April 6, 2006
SoftRock v6.0 Builder s Notes April 6, 006 Be sure to use a grounded tip soldering iron in building the v6.0 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0. inch diameter),
More informationunit 3: GENErAL ElectriCAL SySTEM DiAGNOSiS
Electrical/Electronic Systems unit 3: GENErAL ElectriCAL SySTEM DiAGNOSiS lesson 4: wire and connector repairs I. Connector repairs A. Connector repairs involve fixing damaged wires. Wires are marred due
More informationPhoton Wearable Shield Hookup Guide
Page 1 of 5 Photon Wearable Shield Hookup Guide Introduction The SparkFun Photon Wearable Shield breaks out each pin on the Photon, so it is easier to use the Photon in WiFi wearables projects. Due to
More informationA Deluxe LED Blinky That You Can Build!
Lux Spectralis A Deluxe LED Blinky That You Can Build! Assembly Instructions Contents Step 1: Parts check... 2 Step 2: Tool check... 3 Step 3: Install the computer chip... 3 Step 4: Install the resistors...
More informationInstallation tutorial for Console Customs Xbox 360 MaxFire LITE rapid fire Mod Chip.
Installation tutorial for Console Customs Xbox 360 MaxFire LITE rapid fire Mod Chip. This tutorial is designed to aid you in installation of a console customs MaxFire LITE modchip. This tutorial covers
More informationECE 477 Digital Systems Senior Design Project. Module 11 Board Assembly and Soldering Techniques
2011 by D. G. Meyer ECE 477 Digital Systems Senior Design Project Module 11 Board Assembly and Soldering Techniques Outline I ve got my board, now what? Which end of this thing gets hot? Flux is your friend.
More informationTips in Soldering. By Jesus Beltran. Team J (AKA J Crew) EEC 134AB, Professor Xiaoguang Liu UC Davis College of Engineering
Tips in Soldering By Jesus Beltran Team J (AKA J Crew) EEC 134AB, 2015 16 Professor Xiaoguang Liu UC Davis College of Engineering INTRODUCTION Basic soldering skills is a trait that every electronic/electrical
More informationMusic Thing Modular SimpleEQ Construction Guide (1206 version)
Music Thing Modular SimpleEQ Construction Guide (1206 version) Page 1 Useful Links The latest version of this doc and BOM can always be found at http://thonk.co.uk/documents/eq/ A build thread on the Muffwiggler
More informationSSRP LTC1746 Assembly Manual V0.1 Check the most recent version
SSRP LTC1746 Assembly Manual V0.1 Check the most recent version http://oscar.dcarr.org/ssrp/hardware/ltc1746/ltc1746.php Introduction This manual details the general assembly process for the SSRP LTC1746
More informationRAY S REWORK SECRETS TRAINING CERTIFICATION TEST (DVD-13C) v.3
This test consists of twenty multiple-choice questions. All questions are from the video: Ray s Rework Secrets (DVD-13C). Each question has only one most correct answer. Circle the letter corresponding
More informationENVIRONMENTAL. Operating Temperature: -40ºC to +125ºC. Insulator Color 9 = UL White 8 = UL Black Special Order
The market and applications for simple and reliable discrete Wire-to-Board connectors continue to evolve. AVX first introduced the 9175 series of surface mountable Insulation Displacement Connectors (IDC)
More informationBill of Materials: PWM Stepper Motor Driver PART NO
PWM Stepper Motor Driver PART NO. 2183816 Control a stepper motor using this circuit and a servo PWM signal from an R/C controller, arduino, or microcontroller. Onboard circuitry limits winding current,
More informationSTEADY HAND GAME WITH LATCHING LED
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS TEST YOUR HAND-EYE COORDINATION WITH THIS STEADY HAND GAME WITH LATCHING LED Version 2.0
More informationInduction Heater Coil Kit Compact low voltage, high current induction coil
Induction Heater Coil Kit Compact low voltage, high current induction coil Model: CT-400-KIT Features and Specifications High power water cool-able copper coil PCB Layout designed to reduce eddy losses
More informationV6.2 SoftRock Lite Builder s Notes. November 17, 2006
V6.2 SoftRock Lite Builder s Notes November 17, 2006 Be sure to use a grounded tip soldering iron in building the v6.2 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0.1 inch
More informationAssembly and Installation Instructions for White Oak Audio Design TM-1001 LED board
Thank you for purchasing White Oak Audio Design s TM-1001 Upgrade LED Light Board. White Oak Audio Design products are meticulously engineered and tested to ensure a direct drop in fit with your tuner.
More informationFrivolous Engineering Useless Machine Soldering Instructions
Frivolous Engineering Useless Machine Soldering Instructions The electronics assembly for the Useless Machine is very easy to solder together. It consists of 11 parts as shown in the photo. Required tools
More informationConstruction Hints and Techniques
Construction Hints and Techniques You just get finished building a Microwave project and it looks beautiful. After admiring it for awhile you decide to spark it up. All of the voltages and currents look
More informationIntroduction. Pictures in this lab have been taken from Pre-Lab Homework
Introduction This lab relates to material in Hecht, Chapter 18. In this lab you will explore the concepts of circuits, resistors, and capacitors, by actually building a small circuit that is yours to keep!
More informationPacific Antenna 20 and 40M Lightweight Dipole Kit
Pacific Antenna 20 and 40M Lightweight Dipole Kit Diagram showing configuration and approximate lengths 8 3 16 9 16 9 8 3 Description The Pacific Antenna lightweight dual band, trap dipole kit provides
More informationSwitcher Assembly guide. Switcher Assembly guide 1. Soldering. 2. Switcher3 vs Switcher2. 3. PCB split.
Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about safely handling
More informationGertboard Assembly Manual Rev 1.1
Gertboard Assembly Manual Rev 1.1 The Gertboard is an add-on GPIO expansion board for the Raspberry Pi computer. It comes with a large variety of components, including buttons, LEDs, A/D converters, DACs,
More informationWarm Tube Clock. Before we start, please make sure that you have all required parts that come for the IN-16 Nixie shield :
Warm Tube Clock Assembly Instructions for the IN-16 Nixie shield Introduction Congratulations on your purchase of OSH Nixie Tube Clock. In this document you will see all steps you need to follow in order
More informationLead Trimming and Hand Soldering Guidelines for VPT DC-DC Converters and Accessory Products
APPLICATION NOTE Lead Trimming and Hand Soldering Guidelines for VPT DC-DC Converters and Accessory Products DC-DC CONVERTERS AND ACCESSORIES AN002-2.0 Page 1 of 7 Contents: Introduction... 3 Lead Trimming...
More informationDIODE / TRANSISTOR TESTER KIT
DIODE / TRANSISTOR TESTER KIT MODEL DT-100K 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Assembly and Instruction Manual Elenco
More informationLITTLE NERD v1.1 Assembly Guide
last update: 9. 3. 2016 LITTLE NERD v1.1 Assembly Guide bastl instruments.com INTRODUCTION This guide is for building Little Nerd module from Bastl Instruments. It is good to have basic soldering skills
More informationBill of Materials: General Purpose Alarm, Pulsed PART NO
General Purpose Alarm, Pulsed PART NO. 2190207 I hate alarms that sound continuously - unless they are smoke alarms. Smoke alarms should be annoying, but others should not. I wanted an alarm for a function
More informationPacific Antenna 20 and 40M Lightweight Dipole Kit
Pacific Antenna 20 and 40M Lightweight Dipole Kit Diagram showing configuration and approximate lengths 8 6 16 9 16 9 8 6 Description The Pacific Antenna lightweight dual band, trap dipole kit provides
More informationSMT REVERSE POLARITY PROTECTION
SMT REVERSE POLARITY PROTECTION We have all done it, or will one day, hook the power cables to the radio backwards. Hopefully little to nothing will happen. Sometimes it s a minor repair like replacing
More informationSEMITOP Mounting instructions
SEMITOP Mounting instructions ESD protection... 1 Heat sink specification... 1 Mounting surface... 2 Assembling Steps... 3 Thermal grease application... 4 Assembly on heat sink... 4 Connecting SEMITOP
More informationCircuit Board Assembly Instructions for Babuinobot 1.0
Circuit Board Assembly Instructions for Babuinobot 1.0 Brett Nelson January 2010 1 Features Sensor4 input Sensor3 input Sensor2 input 5v power bus Sensor1 input Do not exceed 5v Ground power bus Programming
More informationLDB-1 Kit Instructions Page 1 of 8
LDB-1 Kit Instructions Page 1 of 8 Important Information Congratulations and thank you for your purchase of the LDB-1 Little Drummer Boy Analog Drum Machine Kit! Before you start, please read the enclosed
More informationReflow soldering guidelines for surface mounted power modules
Design Note 017 Reflow soldering guidelines for surface mounted power modules Introduction Ericsson surface mounted power modules are adapted to the ever-increasing demands of high manufacturability and
More informationcourtesy Wikipedia user Wikinaut
What's a PCB? https://learn.sparkfun.com/tutorials/pcb-basics Printed circuit board is the most common name but may also be called printed wiring boards or printed wiring cards. Before the advent of the
More informationInstallation tutorial for Console Customs Xbox ONE MaxFire ONE V2 PCB
Installation tutorial for Console Customs Xbox ONE MaxFire ONE V2 PCB This tutorial is designed to aid you in installation of a console customs MaxFire ONE V2 Circuit board in the newer Xbox One Controllers
More informationLine-Following Robot
1 Line-Following Robot Printed Circuit Board Assembly Jeffrey La Favre October 5, 2014 After you have learned to solder, you are ready to start the assembly of your robot. The assembly will be divided
More informationSolder is a metallic glue that holds the parts together and forms a connection that allows electrical current to flow.
Proper Soldering & Desoldering High Performance Ultrasonic Range Finders Techniques of a MaxBotix Sensor Materials Needed for Soldering Goggles Hands-free clamp Wire stripper Soldering iron with stand
More informationIntroduction to Soldering
Introduction to Soldering The Soldering Iron American Standard Wire Gage (AWG) Solder The Soldering Process Stripping & Tinning Wire Connecting/Soldering Wire Component Soldering De-Soldering Lab Exercise
More informationLunarBlast v1.0. Optical Tremolo. Description:
LunarBlast v1.0 Optical Tremolo Description: Based on the venerable DIY Tremulus Lune classic circuit, www.madbean.com forum member CultureJam created this awesome sounding tremolo dubbed the Shoot the
More informationHow To Make A Basic DC Controller For Model Trains.
How To Make A Basic DC Controller For Model Trains. By John Rumming. Welcome to another of my PDF how to documents. This one will cover a topic of a basic DC controller. There are a minimal amount of parts,
More informationWax Pattern Assembly Handbook: 11 Catalog and Price List. Wax
Wax Pattern Assembly Handbook: 11 Catalog and Price List Wax The BEST way to seal patterns Wax Connections has been leading the investment casting industry since 1993, producing pattern sealing equipment.
More informationENVIRONMENTAL. Operating Temperature: -40ºC to +125ºC 0XX. Contact Size. Contact Wire Max Size Gauge Insulation mm Contact
The Industrial and Solid State Lighting markets continue to look for new products which will reduce size and cost without jeopardizing performance. The new dual-beam boxed contact system from AVX surface
More informationTip: 3425 Kittle with LokSound Micro V4.0 Conversion and LED Lighting Date:
Hi All, Ed Lekanides sent me this article where he used a LokSound Micro V4.0 decoder to convert his Kittle. He shows what he had to do differently to my original article to complete the conversion. My
More informationConstruction Guide European Version
Construction Guide European Version PCB This section describes how to build up the DRO-350 printed circuit board (PCB). The bare PCB is available for purchase on the order page. Static Protection Bare
More informationRepairing your Porsche 928 Central Warning System (CWS) controller
Repairing your Porsche 928 Central Warning System (CWS) controller Disclaimer: This procedure is for a 1984 Porsche 928 S controller. Overview: Under the left foot pedal (dead pedal) of the Porsche 928
More informationQUASAR ELECTRONICS KIT No DRILL SPEED CONTROLLER
QUASAR ELECTRONICS KIT No. 1074 DRILL SPEED CONTROLLER General Description If you work with an electric drill and unless you are lucky enough to own one of the most sophisticated models with speed control,
More informationELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS Lesson 13 EET 150 Electrical Connections Learning Objectives In this lesson you will: see different methods of making electrical connections. learn a procedure for making soldered
More informationModifying a USB sound fob to act as a repeater interface for app_rpt
Modifying a USB sound fob to act as a repeater interface for app_rpt This document explains how to modify a USB sound fob to work as a repeater interface for app_rpt. The following materials and tools
More informationHauptwerk Hardware Interface Board Kit for the Universal Midi Encoder Instruction Manual
Hauptwerk Hardware Interface Board Kit for the Universal Midi Encoder Instruction Manual Hauptwerk Hardware 2016 Page 1 Release 1.2 February 2016 Table of Contents Introduction...3 Parts Identification...4
More informationTS500 Assembly guide. Soldering. TS500 Assembly guide Main PCB 1. Diodes. Document revision 1.2 Last modification : 17/12/16
TS500 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationSMT - TRAINING COURSE
SMT - TRAINING COURSE MODEL SM-200K Surface Mount Technology Kit Assembly and Instruction Manual ELENCO Copyright 2016, 2000 ELENCO Electronics, Inc. Revised 2015 REV-P 753200 No part of this book shall
More informationENVIRONMENTAL. Operating Temperature: -40ºC to +125ºC. Wire Gauge Size
The 917X series of surface mount Insulation Displacement Connectors (IDC) were developed to meet the harsh automotive and industrial market applications for connecting individual wires directly to a PCB
More informationAssembly Instructions for B7971 Smart Socket
Assembly Instructions for B7971 Smart Socket Identification and installation of the resistors, Fig1 Segment 1,R1, 22k Segment 4, R4, 22k Segment 2, R2, 27k Segment 3, R3, 27k Segment 5, R5, 27k Segment
More informationFigure 1. CheapBot Line Follower
The CheapBot Line Follower v2.0 is a plug-in single-board sensor for almost any programmable robot brain. With it, a robot can detect the presence of a black or white zone beneath its two sensors. In its
More informationIR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015
IR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015 1 2 For the main circuits of the line following robot you soldered electronic components on a printed circuit board (PCB). The
More informationWarning: CHOKING HAZARD -Small Parts. Not for Children Under 9 yrs. Kit Recommended for Ages 12 and up.
The Original Warning: CHOKING HAZARD -Small Parts. Not for Children Under 9 yrs. Kit Recommended for Ages 12 and up. Table of Contents Soldering.. 3 How the WASP Works.. 7 The Build...... 12 Troubleshooting......30
More informationRF Current Meter Kit
Kit When assembled, this kit provides you with a simple but effective means of measuring the current in antenna wires, and of looking for braid currents on coax feeders. The more current you can get flowing
More informationFor board-to-fpc. Narrow pitch connectors (0.4mm pitch)
Automation Controls Catalog For board-to-fpc Narrow pitch connectors (0.4mm pitch) F4 Series 5.0mm 4.1mm RoHS compliant FEATURES 1. 0.9 mm mated height low profile two-piece type connectors 2. Strong resistance
More informationaccessories The perfect complement for soldering and desoldering jobs
accessories The perfect complement for soldering and desoldering jobs 44 KN- Nitrogen kit This is the ideal solution for improving the quality of any solder joint by using nitrogen because it provides
More informationFirefly Jar Learn to Solder Kit
Firefly Jar Learn to Solder Kit Parts Tools A. Firefly Jar PCB B. 10mm Flickering LED (White or Yellow) C. Resistor D. Tilt Switch (Black or Green) E. Battery Holder F. Velcro ( Not Pictured) G. Jar (
More informationHeartboard PCB Assembly Instructions
Heartboard PCB Assembly Instructions Thanks for purchasing a Heartboard! These instructions will guide you through assembling and testing the Heartboard. Let s get started! Stuff you need Soldering iron
More informationTelecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering tips: Removing Current Wiring: Step 1. Step 2.
Telecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers Wire Strippers 3/8 Drill Bit 5/32 Drill Bit
More informationQRPGuys Michigan Mighty Might Plus 40M Transmitter
QRPGuys Michigan Mighty Might Plus 40M Transmitter First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use
More informationTeam Xecuter Joycon Mod By: XxWiReDxX
Team Xecuter Joycon Mod By: XxWiReDxX Works With Every Switch SX OS Works with every Nintendo Switch and every firmware version! Play Every Game With SX OS you can play all your favorite games straight
More informationTen Tec DDS Board Assembly Procedure
05 May 2014 Ten Tec DDS Board Assembly Procedure You will find a photo of a completed board at the end of these instructions. Refer it whenever clarification is required. 1. AD9835 Attachment If you purchased
More informationLearn to solder electronics with the Maker
Learn to solder electronics with the Maker Shed Solder Badge! How to assemble the Maker Shed Badge kit. Written By: Alexander ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 INTRODUCTION The Maker Shed
More informationStandard AWG: WTB
The 917X series of surface mount Insulation Displacement Connectors (IDC) were developed to meet the harsh automotive and industrial market applications for connecting individual wires directly to a PCB
More informationPacific Antenna Low Pass Filter Kit
Pacific Antenna Low Pass Filter Kit Description Many basic transmitter and/or transceiver designs have minimal filtering on their output and frequently have significant harmonic content in their signals.
More informationFigure 1. CheapBot Smart Proximity Detector
The CheapBot Smart Proximity Detector is a plug-in single-board sensor for almost any programmable robotic brain. With it, robots can detect the presence of a wall extending across the robot s path or
More informationInstructions for building the PGA432 70cm preamplifier
Instructions for building the PGA432 70cm preamplifier Issue 0.2 17/11/16 First step Carefully place the PCB, track side up, inside the lid of the tinplate box. Ensure that the PCB is centrally located.
More informationDIODE / TRANSISTOR TESTER KIT
DIODE / TRANSISTOR TESTER KIT MODEL DT-100K Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 1988 Elenco Electronics, Inc. Revised 2002 REV-K 753110 DT-100 PARTS LIST If you are a student,
More information