How to install an aftermarket stereo/navigation
|
|
- Arabella Harper
- 6 years ago
- Views:
Transcription
1 How to install an aftermarket stereo/navigation As most of you know, the 2002 (and others) Sport Trac has the 1 ½ DIN radio. This makes for some narrow choices when putting in a radio with navigation. I found the VR3 VRVD640G that has AM/FM/CD/DVD/SD/USB/Navigation with a 4 screen that fits into the 1 ½ DIN opening. (Available at WalMart and other places for under $400.00) Required Tools Ford Radio Tool (A lot easier to use than the coat hanger), Ford radio installation kit & wiring harness, volt/ohm meter, needle nose pliers or wire stripper, wire nuts (small blue ones are perfect size) and a coat hanger (I ll get to that later). STEP 1 Clean out the front area of your Sport Trac. This means stuff that you have on the floor board, on the seats, in the cup holders. No need to have clutter laying around when you start working. Next, and this is VERY important. Turn on your existing radio and EJECT any and all CD s and/or cassette tapes! There is nothing worse than after you install your new radio and then trying to find that Pink Floyd CD which is still in the old unit! STEP 2 Take your key OUT of the ignition. Using the Ford Radio Tool, insert into release holes until you hear them click. At the same time, push tools outward and pull towards you. Radio should pull straight out. On the back of my radio, I unplugged 3 black cables and 1 antenna jack. Just let them hang there for now. STEP 3 Take new wiring harness and connect it to the corresponding jack to ensure it fits. (Note, when you plug the new wiring harness into the existing one, be assured that 75% of the colors will NOT match up!)
2 Somewhere in you new wiring harness kit, you should find the color code layout. Mine told me that the YELLOW wire would be battery and the RED would be ignition. Call me skeptical, but I trust in God only! Take volt/ohm meter at test YELLOW wire to ensure it has battery on it (don t forget, on your V/O meter, the red wire touches the yellow wire and the black wire goes to ground). You should read around 13 VDC. Now, put your key back in the ignition and turn it to accessory. Put your V/O meter on the RED wire to see 13 VDC. If all of this is right, turn off your Sport Trac and take out the key. At this point, many people opt to go the safe route and disconnect the battery. That is your call. Just remember that you have to re-connect the battery before you test your radio. STEP 4 Install your conversion kit. This is what will fill in that space below the radio. Do this now instead of having to pull your wires apart because you jumped ahead a step. The kit should just snap right into place without much pressure. Make sure it is all clicked into place and is secure. My radio came with a DIN sleeve that fit around the radio and into the kit. Install it if necessary.
3 STEP 5 Time to test fit your unit. Take your new radio and slide it into the bracket until it clicks into place. Don t worry that it is in there secure, it s supposed to be! Your new radio comes with the removal tool, so just slide them in and pull it back out.
4 STEP 6 Time to get those wire nuts ready. Since you already cleaned out the front of your Sport Trac, you should have an empty cup holder. What a perfect place to put all your wire nuts! Get your needle nose pliers out and skin back about ½ inch of all the wire (both from your new harness and what is on the radio). Take and match up all your wires according to the instructions. On each set of wires, twist on the wire nuts till they are tight until you have connected all the wires that need to be. You may have some left over wires, but that is OK and they go to other things like power antennas, dash lights, etc. STEP 7 It s do or die time! Take your wire harness and plug one end into the Ford harness (that is hanging out of the dash) and plug the other end into your new radio. DON T FORGET TO PLUG IN YOUR ANTENNA!!!! If you have disconnected the battery, now is the time to hook it back up. Take your key and put in the ignition and turn it to accessories. Turn on your new radio and it should light right up! If it didn t, turn off your ignition and recheck all your connections.
5 STEP 8 You are almost done. You should have a cable that is for your navigation antenna. I placed mine in the left hand corner on the black finish so it is not easy to see. Use a piece of double sided tape (included with the radio) to secure it. Now snake your cable to the rear of the radio via the hole in the dash (in other words, take that coat hanger, put a loop on one end and send it into the hole where your radio will be going until you see it come out under the dash. Tape the antenna cable to it and pull it GENTLY back through the hole and then connect it to the antenna jack. Now take all your wires and gently push them into the radio slot. Mark sure they go to either the right or left of the unit as you don t want it to interfere with the rear stop of the installation kit (the stop on my kit is what helps hold the radio secure in the dash). Push the radio all the way in until it clicks into place. Give it a gentle tug forward to ensure it doesn t slide out. Put your key back in the ignition and turn on your Sport Trac. Your radio/nav unit should power right! If it doesn t come on, you will need to pull it out to make sure none of your wire nuts came loose. Resecure and install. The only thing left to do is READ THE MANUAL and become familiar with your new radio/navigation unit!
6
7
Ford in dash cd changer fix by Radmacks
Ford in dash cd changer fix by Radmacks Disclaimer: This tutorial is provided for informational purposes only. I take no responsibility for anything you break, damage, set on fire, or anybody you tell
More informationRPS. XR Front Drive Updates CORPORATION
FACTORY CAT 1. To start a replacement of the XR Front Wheel Drive, make sure the machine is on level ground with the rear wheels chocked and always disconnect the batteries. 2. Locate the Positive and
More informationHow to Hard- Wire your Zumo 665 to the Slingshot Infotainment Center
How to Hard- Wire your Zumo 665 to the Slingshot Infotainment Center You need a Zumo 665 kit that comes with Your Zumo 665. If you left it on a bike that you traded, then go to garmin. com or Amazon. com
More informationGT3B Hack Kit Install Instructions Written By Austin Hutchison
GT3B Hack Kit Install Instructions Written By Austin Hutchison Step 1: Remove 4 screws located on top of the radio. 1 Step 2: There are small plastic latches that also hold the top in place. The easiest
More information1999 I Click on a link tab to jump to that page
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,,2000. Factory Radio
More informationTaurus - Ford Sable - Mercury
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
More informationInstallation instructions, accessories. TV receiver, digital
Installation instructions, accessories Instruction No 30756561 Version 1.1 5 Part. No. 30756181, 30756569 TV receiver, digital Volvo Car Corporation TV receiver, digital- 30756561 - V1.1 Page 1 / 36 Equipment
More informationTRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS
DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Swing s 73 74 NOTES INSTALLATION OF A GDM-SWING DOOR Phillips Head Screwdriver (2) - 1/8" Drift Punches (forged) Top Bracket NOTE: It may be necessary
More informationBi-Color Signal Mirror Installation Instructions
Bi-Color Signal Mirror Installation Instructions 2005-2009 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0141-0 Rev. A2 (3/30/09), BTV 2007 Muth Mirror Systems, LLC Page 3 of 13PplPage
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2006 2007 Honda Ridgeline THE safety accessory of the 21 st Century. P/N 210 0142 0 Rev. A (9/5/07), BTV 2007 Muth Company, LLC Professional Installation Recommended:
More informationOpen Air. Kit includes: Drawer Full Indicator board assembly, (2) retainers, and (4) screws. PREPARATION
Open Air Installation Video You will need: 8-inch #2 Phillips screwdriver Needle-nose pliers DFI INSTALLATION GUIDE For installation videos, visit the Customer Service playlist at www.youtube.com/user/thelitterrobot
More informationSunrise Deck Assembly Instructions for Kingston Left
Sunrise Deck Assembly Instructions for Kingston Left It s easiest to build the deck frame first like it will be lying on its back and then after all 4 legs and horizontals are in place, tip the deck toward
More informationiphone 4S Dismantling Instructions
iphone 4S Dismantling Instructions These instructions will show you how to open the iphone to replace the digitizer, LCD screen and other internal parts. Opening your iphone will void your warrantee, and
More informationMove System Swivel Caster Installation ( )
Move System Swivel Caster Installation (002-10265-00) Caution Always disconnect power to chair before removing covers or performing any service procedures. Step 1: Remove Top Cover A) Position chair to
More informationAUDI A8 D3 REPLACING THE OUTSIDE DRIVER DOOR HANDLE
AUDI A8 D3 REPLACING THE OUTSIDE DRIVER DOOR HANDLE The keyless entry system in the D3 is a great feature. If you have the car key fob in your pocket, putting your hand under the door handle will unlock
More informationSUT-1000CLC ASSEMBLY REQUIREMENTS
SUT-1000CLC Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all
More informationINVENT3D Printer Kit Disassembly Instructions
INVENT3D Printer Kit Disassembly Instructions Version 6 AST2 10/26/16 1 I. General Disassembly Instructions Use the case layer drawings to ensure that components are stored in the appropriate location
More informationConnecting a Warp Feed to an Intelliframe
Connecting a Warp Feed to an Intelliframe So you want to trigger your Warp Feed every time you pull the trigger? Sounds like a great idea! This step by step picture story will guide you through this process.
More informationMotorola E815 / E816 Disassembly / Assembly Guide. Ver. 1.1 By Chubbs_WA
Motorola E815 / E816 Disassembly / Assembly Guide Ver. 1.1 By Chubbs_WA April 10, 2007 Table of Contents Disassembly Tools needed 3 Disassembly for dummies 4 Just a note 5 Disassembly of keypad housing
More informationPRINTER REPAIR ARTICLE HP LJ 4345/M4345 Swing Plate Replacement
a1 output bin a2 DUPLEXER a4 FORMATTER COVER a5 FORMATTER a3 fuser entr. guide PRINTER REPAIR ARTICLE HP LJ 4345/M4345 Swing Plate Replacement Grinding noise near the fuser means it is time to replace
More informationRemoving outter components
Y Axis Motor Replacement Replacing the Y axis motor is a process that requires the individual to be somewhat mechanically inclined and can follow detailed instructions. If any of the following steps are
More informationLDB-1 Kit Instructions Page 1 of 8
LDB-1 Kit Instructions Page 1 of 8 Important Information Congratulations and thank you for your purchase of the LDB-1 Little Drummer Boy Analog Drum Machine Kit! Before you start, please read the enclosed
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Toyota RAV4 1996-2000 THE safety accessory of the 21 st Century. P/N 210-0034-0 Rev B1 (11-19-02), GG 2002 Muth Co. LLC. Note: Professional Installation Recommended
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Honda CRV 1997-2003 THE safety accessory of the 21 st Century. P/N 210-0032-0 Rev B2 (6-26-04), GG 2003 Muth Mirror Systems, LLC. Note: Professional Installation
More informationMS2 Straight Key Kit Assembly Manual
American Morse Equipment MS2 Straight Key Kit Assembly Manual Thank you for purchasing our MS2 Miniature Straight Key Kit! Please take a few minutes to look over these instructions before starting assembly.
More informationPorsche 911 (996) Porsche Boxster (986) B
INSTALLATION INSTRUCTIONS FOR PART 99-9605B Porsche 911 (996) 1999-2005 Porsche Boxster (986) 1997-2004 99-9605B KIT FEATURES ISO DIN radio provision with pocket (NAV models only) ISO DDIN radio provision
More informationThe Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )
P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your
More informationHow To: D9 steering wheel & COM2000 change
How To: D9 steering wheel & COM2000 change This is for my '04 406 HDi estate so I'm not sure how applicable it is - feel free to edit. Oh, and delete this bit when you're done... NB: The COM2000 stuff
More informationAnswer Power Beam and Boundary Screen
Answer Power Beam and Boundary Screen 5/16 MAGNETIC 3/8 If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by
More informationKitronik Ltd How to make a be seen be safe armband
Kitronik Ltd How to make a be seen be safe armband Introduction This project uses a basic e-textiles circuit but a popper has been added into the circuit to create a switch. When the popper is open the
More informationBABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms
BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away
More information626 - Mazda MX-6 - Mazda
Factory Radio Other Documents Available For This Vehicle: No additional documents available at this time Adobe Acrobat Reader Printing Tips: 1) Select FLE then PRNT and select your printer. 2) n the print
More informationAUDIO SYSTEMS 8F - 1 AUDIO SYSTEMS CONTENTS
TJ AUDIO SYSTEMS 8F - 1 AUDIO SYSTEMS CONTENTS page GENERAL INFORMATION INTRODUCTION... 1 DESCRIPTION AND OPERATION ANTENNA... 1 IGNITION-OFF DRAW FUSE... 1 RADIO... 1 RADIO NOISE SUPPRESSION... 2 SPEAKER...
More informationHatchback Wing Riser Kit
Hatchback Wing Riser Kit 2015-06-11 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
More informationSignal Mirror Installation Instructions Toyota Tacoma
Signal Mirror Installation Instructions 2005-2015 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0115-0 Rev. A4 (3/11/15), BTV 2005 Muth Mirror Systems, LLC Page 3 of 12PplPage 3 of 12
More informationPowerbook G3 Lombard (1999) USB Repair Manual
Powerbook G3 Lombard (1999) USB Repair Manual Copyright 2003 Powerbookmedic.com. All rights reserved. Any portion of this manual may not be copied, reproduced, or distributed without the express written
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2004 2008 Ford F-150 XLT, FX4, & Lariat Pre-wired without side signals Pre-wired with side signals Without side directional lights, see page 2 With side directional
More informationDIY! How to Make Your Own. Trip Line Detonator for Use With Big Blast Target InflatorÔ
IMPORTANT To ensure the templates print the correct size make certain that Scale or Scaling in your PDF printing program is set to Off or None. Trip Line Detonator for Use With Big Blast Target InflatorÔ
More informationTOYOTA COROLLA EC REARVIEW MIRROR Section I Installation Preparation
Section I Installation Preparation Part Number: PT374-02030 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/compass & Maplights 2 1 Hardware Bag
More informationGENUINE ACCESSORIES INSTALLATION INSTRUCTIONS. ITEM QTY DESCRIPTION Usage Chart
PART NUMBER: 0000 8C R0 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0554-000* APPLICABLE MODELS: 203 > CX-5 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart MIRROR ASSEMBLY: Mirror
More informationABM International, Inc. Navigator Assembly Manual
ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor
More informationE-FLIGHT BLADE CX COMPLETE DISASSEMBLY JANUARY 2006
E-FLIGHT BLADE CX COMPLETE DISASSEMBLY JANUARY 2006 AERONUTS THIS IS NOT AN OFFICIAL E-FLIGHT MANUAL OR INSTRUCTION. IT IS BEING PROVIDED FOR INFORMATIONAL PURPOSES ONLY. AUTHOR ASSUMES NO LIABILITY FOR
More informationBrewsBySmith.com STC DIY Kit
BrewsBySmith.com STC-1000 + DIY Kit Contact Information: Greg Smith www.brewsbysmith.com greg@boostbysmith.com I. Hardware Included: STC-1000 flashed with latest software (v1.06 currently) (if purchased)
More information6 th to 12 th grade. 20 minutes prep, 30 minutes activity
Build a Water Bottle Membranophone 6 th to 12 th grade 20 minutes prep, 30 minutes activity A clean empty water bottle, any size (bottles with ridges are best) Scissors Latex, rubber, or vinyl gloves Rubber
More informationFord Pick Up Rear leaf Spring Kit Installation Instructions
1948-1956 Ford Pick Up Rear leaf Spring Kit Installation Instructions 1-800-984-6259 www.totalcostinvolved.com Parts 48 inch leaf (2) springs (4) U-bolts 3/8-24 x l 1/4bolts (16) & nuts (2) 1/2-20 x 4
More informationCOMPONENT LOCATION INDEX
COMPONENT LOCATION INDEX 2004 ACCESSORIES & EQUIPMENT Audio System - TSX Fig. 1: Locating Audio System Components (1 Of 2) Tuesday, March 11, 2008 3:35:47 3:35:51 PM Page 1 Fig. 2: Locating Audio System
More information* * APPLICABLE MODELS: 2014 > MAZDA 3
PART NUMBER: 0000 8C L46 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0604-000* APPLICABLE MODELS: 204 > MAZDA 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart MIRROR ASSEMBLY: Mirror
More informationGoPro Hero Camera Mount. Assembly Manual
GoPro Hero Camera Mount Assembly Manual Introduction Thank you for purchasing the GoPro Hero Camera Mount for Mikrokopter Quad, Hexa and Okto. The Camera Mount is provided as a kit and requires assembly.
More informationP/N LED LIGHT 505EC RETROFIT KIT INSTRUCTIONS
P/N 090513 LED LIGHT 505EC RETROFIT KIT INSTRUCTIONS 1 4 7 12 8 2 5 13 9 11 14 3 6 10 15 PARTS LIST ITEM NUMBER QUANTITY PART NUMBER DESCRIPTION 1 18 IN. 660461 18/2 SVO CORD 2 1 090508 LED LIGHT TRANSFORMER
More informationInstallation Guide for Rough Country 1.25 inch Body Lift Kit w/o Shocks (07-15 Wrangler JK 4 Door) Item # J10048 Option B; Manual
Installation Guide for Rough Country 1.25 inch Body Lift Kit w/o Shocks (07-15 Wrangler JK 4 Door) Item # J10048 Option B; Manual Installation Time: 3 Hours Tools Required: Jack (Tall enough to reach body
More informationInstructions to Convert a 4-foot Florescent Fixture to LEDs Using 60W Power Supply Using 2 or 3 strips 30Dec15
Instructions to Convert a 4-foot Florescent Fixture to LEDs Using 60W Power Supply Using 2 or 3 strips 30Dec15 Thank you for purchasing the Shoplight Solutions 4-ft conversion kit. This is a companion
More informationService Manual for XLE/XLT Series Laser Engravers
Service Manual for XLE/XLT Series Laser Engravers Table of Contents Maintenance...1 Beam alignment...3 Auto focus alignment...8 Bridge alignment...10 Electronics panel replacement...11 X motor change...12
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationSignal Mirror Installation Instructions Honda Odyssey
Signal Mirror Installation Instructions 2005-2009 Honda Odyssey THE safety accessory of the 21st Century. P/N 210-0122-0 Rev. A4 (6/9/09), BTV 2006 Muth Company, LLC PROFESSIONAL INSTALLATION RECOMMENDED
More informationAdding Cabinet to the DCT1900 System
Add a cabinet Adding Cabinet to the DCT1900 System Adding a cabinet to an existing system requires planning to assure a successful addition with minimal downtime and problems. Both software and hardware
More informationNAVIGATION SYSTEM INSTALLATION INSTRUCTIONS
NAVIGATION SYSTEM INSTALLATION INSTRUCTIONS These instructions along with the pictures were performed in a 2008 Yukon. Please use them only as a reference since they might not exactly match your vehicle
More informationMotorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions
Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil 4 Level Phillips
More informationEZ BALANCER II. Please note: The hardware and accessories listed may not be the same as shown. We are always improving the product.
Parts List EZ BALANCER II 2ea. Aluminum Angle Base Frame Members. 2ea. 1/2"x1" Aluminum Angle Cross Frame Members. 2ea. Aluminum Uprights. 2ea. Aluminum Cradles. 4ea. Rubber Cradle Guards. 4ea. Rubber
More information7878 K940. Checkpoint Antenna. Kit Instructions. Issue B
7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory Radio Other
More informationInstalling Your New Creature From The Black Lagoon Tail Light DMD Panel MOD
Installing Your New Creature From The Black Lagoon Tail Light DMD Panel MOD A few things before we start: The wooden speaker panel provided in this MOD was manufactured using a Precision CNC machine and
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2005-2010 Chevy Corvette C6 THE safety accessory of the 21 st Century. P/N 210-0144-0 Rev. A3 (9/29/2011), BTV 2007 Muth Mirror Systems, LLC Page 3 of 10PplPage
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Ford Explorer 1996-2001, Ford Explorer SportTrac 2001, Ford Ranger 1996-2001, Mazda B-2500\B-3000\B-4000 1998-2001, Mercury Mountaineer 1997-2001 THE safety accessory
More informationFM Wireless Microphone Kit Instructions for Assembly Page 1 of 5
Instructions for Assembly Page 1 of 5 1. Find Resistor R1. Remove any tape that may be attached to the leads. Bend the leads as needed to insert Resistor R1 into the printed circuit board in the holes
More informationTHE THUNDERDRIVE (K-950)
THE THUNDERDRIVE (K-950) OUTPUT DISTORTION Unplug when not in use to save battery life. TO AMP IN The Thunderdrive Modkitsdiy.com FROM GUITAR OUT Use these instructions to learn: How to build an effects
More informationPlug-n-Show Stake Down Pixel Tree Kit 16 strips of 25 pixels Assembly Instructions
www.lightorama.com Plug-n-Show Stake Down Pixel Tree Kit 16 strips of 25 pixels Assembly Instructions Read all instructions before you start Kit assembly! STEP 1. Check that all parts are included Parts
More informationInstructions to Convert a 4-foot Florescent Fixture to LEDs Using 100W Power Supply Using 1-4 strips 30Dec15
Instructions to Convert a 4-foot Florescent Fixture to LEDs Using 100W Power Supply Using 1-4 strips 30Dec15 Thank you for purchasing the Shoplight Solutions 100W conversion kit. This is a companion document
More informationInstall The Trailer Lighting Wire Harness Connector
Install The Trailer Lighting Wire Harness Connector This is probably the toughest part of the whole trailer hitch install. It helps to have a little background in electronics, but if you don't then simply
More informationTelecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering tips: Removing Current Wiring: Step 1. Step 2.
Telecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers Wire Strippers 3/8 Drill Bit 5/32 Drill Bit
More informationNeon Dodge/Chrysler/Plymouth Radio Replacement Document #:
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
More informationHQ Precision-Glide Track Upgrade 2 Extension Kit for HQ Studio Frame Part# QF09750
HQ Precision-Glide Track Upgrade 2 Extension Kit for HQ Studio Frame Part# QF09750 Important Note: Upgrading the track system on the HQ Studio Frame requires the use of this 2 Extension Kit (Part #QF09750),
More informationDesigned by Melissa DiRenzo thesweetescape.ca
instructions Designed by Melissa DiRenzo thesweetescape.ca YOU WILL NEED 3 -diameter foam ball Christmas sweater Hot glue gun and glue sticks 3/8 -wide satin ribbon Elastic thread: metallic Note: A child
More informationFull Size Pick Ups - GM Suburban/Yukon/Tahoe - GM Escalade - Cadillac Click on a link tab to jump to that page.
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory Radio Other
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. & nstall Factory
More informationInterra Installation Manual
Interra Installation Manual Instructions to install the Friant Interra panel system Friant & Associates, LLC Table of Contents Getting Started Introduction... 3 General Tools, Staging & Safety... 4 Before
More informationTELESCOPIC GATE MANUFACTURING AND INSTALLATION MANUAL.
TELESCOPIC GATE MANUFACTURING AND INSTALLATION MANUAL. Telescopic gates have been manufactured for many years essentially in the same way they are largely today. In recent years hardware suppliers have
More informationRADIO ANTI TWO-BLOCK SYSTEM
BB-550 TM RADIO ANTI TWO-BLOCK SYSTEM INSTALLATION MANUAL GREER Company 1918 East Glenwood Place, Santa Ana, CA 92705 Tel: (714) 259-9702 FAX (714) 259-7626 BB-550 TM Radio Anti Two-Block System PN W250000
More information* Drill and 3/32" drill bit: for drilling holes in the factory plastic upper for the screws to secure the brackets (factory upper installation only)
* Two slider windows (four sliders windows for the 4-door kit) * Four brackets to secure the windows to the upper door frames (8 brackets for the 4-door kit) * Weatherstrip to seal the windows to the half
More informationXEROX PHASER 3600 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
XEROX PHASER 3600 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS XEROX PHASER 3600 TONER CARTRIDGE REMANUFACTURING THE XEROX PHASER 3600 TONER CARTRIDGE By Mike Josiah and the Technical Staff at UniNet The
More informationHardware and Components:
Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut
More informationF-F-Fiddle Assembly Instructions
F-F-Fiddle Assembly Instructions Bout Bridge Neck Machine Heads/Tuners Truss Rod Strings An open-source FFF 3d-printable electric violin. 1. Assemble materials 5 3 8 1 9,10, 11 7 4 2 6 PARTS 1. Bout part
More informationTerminal Replacement Procedures
HOW TO REPLACE CONNECTOR TERMINALS The terminal repair kits provide necessary tools and materials (terminals, wire seals, and splice connectors) to repair many damaged or faulty connector terminals. However,
More informationINTRODUCTION TO WEARABLES
Table of Contents 6 7 8 About this series Getting setup Making a circuit Adding a switch Sewing on components Complete a wearable circuit Adding more LEDs Make detachable parts......6.7.8 About this series
More informationInstallation Instructions Road King Classic Saddlebag Bezels
Installation Instructions Road King Classic Saddlebag Bezels Thank you for your purchase of Bagger Audio Road King Classic Saddlebag Bezels for your Harley-Davidson motorcycle. We have carefully engineered
More informationINSTALLATION LS MODEL
INSTALLATION LS MODEL Page 2 TABLE OF CONTENTS Section 1: Included parts... pg 4 Section 2: Installing the Shirley Stitcher II on Quilt Frame.. pg 5 Section 3: Connecting Shirley Stitcher II to Tin Lizzie
More informationXT-4015 Disassembly Assembly Guide
XT-4015 Disassembly Assembly Guide Main Unit Disassembly Remove the two screws that in the back of main unit from base as shown. Remove the two screws by turning the main unit to the other side while removing
More informationInstalling the 3 Indexer: PRS Standard Tools
888-680-4466 ShopBotTools.com Installing the 3 Indexer: PRS Standard Tools Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Route Cable into Box...5
More informationThis little piece here I created is some of the scraps and then samples I was making for today s show. And these are wonderful for doing like
Hey everybody, welcome back to Man Sewing. This is Rob and today on the show, I m going to teach you how I like to do my curve piecing. Now I can t take all the credit for this. Ricky Tims, a good friend
More informationRugged Ridge 2 Receiver Hitch Kit (J21068)
Rugged Ridge 2 Receiver Hitch Kit (J21068) Installation Time: 1-2 Hours Tools Required: ¾ Open End Wrench 18 mm Socket ¼ drive Pliers/Needle nose pliers/channel locks, etc. Torque wrench Phillips head
More informationP/N LED LIGHT FI85 RETROFIT KIT INSTRUCTIONS
P/N 090521 LED LIGHT FI85 RETROFIT KIT INSTRUCTIONS 1 4 7 10 11 2 5 8 6 9 12 3 PARTS LIST ITEM NUMBER QUANTITY PART NUMBER DESCRIPTION 1 3 090503 1 METER EXTENSION 2 3 090543 18 LED BULB STRIP (12 IN.)
More informationChapter 6 Frame And Lens Repairs
Chapter 6 Frame And Lens Repairs 6.1 General Information All maintenance on the frame of the EXO Full-Face mask can be accomplished with common hand tools. 6.2 Lens Replacement Tools required: Dow DC-111
More informationThe Festival Assembly Instructions
The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. & nstall Factory
More informationKN-8828B Upgrade Directions
KN-8828B Upgrade Directions This document outlines the steps to take to update earlier Hottop Bean Roasters to the KN-8828B 2007 by Chang Yue and Hottop USA - All Rights Reserved No part of this document
More informationRepairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip
Repairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip Disassembly, repair and reassembly of Wedge Touch mouse when the battery cover will not stay closed. Also is a good guide to repair other
More informationI Click on a link tab to jump to that page. Cover Page
Factory Radio Other Documents Available For This Vehicle: No documents available at this time Adobe Acrobat Reader Printing Tips: 1) Select FLE then PRNT and select your printer. 2) n the print options
More informationPicture 4. Picture 1. Picture 2
HP-41C Card Reader Repair The Short Fix Approach Tools needed include the following shown below. Two sizes of Phillips head screw drivers are good. One small and one medium small. Needle nose pliers are
More informationP/N LED LIGHTS 6509/9012/12012 MACHINES
P/N 090517 LED LIGHTS 6509/9012/12012 MACHINES 4 1 8 12 5 9 13 2 6 10 3 7 11 14 PARTS LIST ITEM NUMBER QUANTITY PART NUMBER DESCRIPTION 1 18 IN. 660461 18/2 SVO CORD 2 1 090508 LED LIGHT TRANSFORMER 3
More information1 Fit an eyelet through the loop you have made, adjusting the LED leg as necessary, so it fits closely to the loop
1 Fit an eyelet through the loop you have made, adjusting the LED leg as necessary, so it fits closely to the loop 2 Use the Narrow Nosed Pliers to shape the end of the LED leg into a circular or triangular
More informationALUMINUM AIR TRIM INSTALLATION INTRODUCTION
ALUMINUM AIR TRIM INSTALLATION INTRODUCTION KEISER CORPORATION has always taken pride in designing and engineering the highest quality equipment on the market. This means that you will receive years of
More information