Connection between thermal printer DPU-414 and measuring equipment

Transcription

1 Connection between thermal printer DPU- and measuring equipment When connecting the DPU- to various measuring instruments, function settings at the DPU- must be changed. The procedure for changing settings is described below. You should also refer to the section ". Function Setting Items" on pages - 9 of the instruction manual for the thermal printer DPU-.. Set the power switch to while keeping the LINE switch depressed. Hold the switch down until printing starts.. When printing starts, release the switch. The current settings are printed out.. On the last line, the following query appears. Continue? : Push 'On-line SW' Write? : Push 'Paper feed SW' Press the LINE switch to select "Continue".. "Dip SW-" is printed and the function setting mode is enabled. Make the input for the connected measuring instrument by referring to the table below. To choose the "" setting, press the LINE switch. To choose the "" setting, press the FEED switch. The selected setting is printed out.. When the settings for switches - are completed, the unit returns to the state of step. Make the settings for "Dip SW-" and "Dip SW-" in the same way. When all settings have been made, the following query appears again. Continue? : Push 'On-line SW' Write? : Push 'Paper feed SW' Press the FEED switch to select "Write". The message "DIP SW setting complete!!" is printed, and the setting mode is terminated.

2 DIP switch setting example An example for the printout produced during the DIP switch setting procedure for the integral noise level meter NL-0 is shown below. (The font of the actual printout will be different.) Continue? : Push 'On-line SW' Write? : Push 'Paper feed SW' Dip SW- () : Input = Serial () : Printing Speed = High () : Auto Loading = () : Auto LF = () : Setting Command = Enable () : Printing () : Density () : 00 % Continue? : Push 'On-line SW' Write? : Push 'Paper feed SW' Dip SW- () : Printing Columns = 0 () : User Font Back-up = () : Character Select = Normal () : Zero = Normal () : International () : Character () : Set () : = Japan Continue? : Push 'On-line SW' Write? : Push 'Paper feed SW' Dip SW- () : Data Length = bits () : Parity Setting = () : Parity Condition = Even () : Busy Control = X/X () : Baud () : Rate () : Select () : = 900 bps Continue? : Push 'On-line SW' Write? : Push 'Paper feed SW' DIP SW setting complete!!

3 DIP switch setting print example An example for the printout of the completed DIP switch setting for the integral noise level meter NL-0 is shown below. (The font of the actual printout will be different.) This is printed during steps and described on page. [mdip SW setting mode] Dip SW- () : Input = Serial () : Printing Speed = High () : Auto Loading = () : Auto LF = () : Setting Command = Enable () : Printing () : Density () : 00 % Dip SW- () : Printing Columns = 0 () : User Font Back-up = () : Character Select = Normal () : Zero = Normal () : International () : Character () : Set () : = Japan Dip SW- () : Data Length = bits () : Parity Setting = () : Parity Condition = Even () : Busy Control = X/X () : Baud () : Rate () : Select () : = 900 bps

4 DIP switch setting table for various measuring devices NA-9/9E NL-0/ NA- Model VA-0 SA- Model NL0/0A NL- Model SW- SW- SW- SW- SW- SW- SW- SW- SW-

5 SW- SW- SW- SW- SW- SW- SW- SW- SW- NL-0/ 00 bps NL-0/ 900 bps AM-09S AM-09T Model Model Model

6 SW- SW- SW- SW- SW- SW- SW- SW- SW- NA- 00 bps NA-/ VA- 900 bps VM-/9 Model Model Model

7 SW- SW- SW- SW- SW- SW- SW- SW- SW- UV-0 UN-0 VM- VE-0 VM- VM-A Model Model Model

8 SW- SW- SW- SW- SW- SW- SW- SW- SW- AA- 00 bps AA- 00 bps AA- 00 bps Model Model Model

9 @ A - & A % 9 9!! " " # # $ $ % & % & 9 9!! " # $ " # $ % % & & 9! 9!!! " " # # $ $ % % & & 9

10 Set the RS-C mode at the KM-0B/ KM-0C to "Print A Record" Set the print mode at the KM- to "ALL" or "Alr" The setting of SW- has no effect. Model KM-0B/C Model KM- SW- SW- SW- SW- SW- SW- 0

11

12 -0- Higashimotomachi, Kokubunji, Tokyo - Japan No. 9