MINI PRINTER. Contents. Instruction Manual DESK TYPE SE7200 SD SE7200 PD SE7200 ST SE7200 PT. Chapter 1. Pre-face. Chapter 2.

Transcription

1 Instruction Manual SE 7200 DESK TYPE SD PD ST PT Chapter 1. Pre-face 1-1. Feature 1-2. Usage Chapter 2. Introduction 2-1. Specification 2-2. Control Panel Function 2-3. Self Test Mode 2-4. Hex Decimal Dump Mode Chapter 3. Connection 3-1. Serial Interface 3-2. Parallel Interface 3-3. Others Chapter 4. Dimension Contents Chapter 5. Command Mode 5-1. Basic Command mode 5-2. EPSON TM-U200 Command mode 5-3. CITIZEN idp-3540 Command mode 5 4. THERMAL Command mode(epson TM-88Ⅱ) 5 5. THERMAL Command mode (CITIZEN idp-3540 command) 2

2 Chapter 1. Pre-face This product, Mini Printer can be applied to various systems, like Factory automation, Bill issuing machine, Digital scale, Digital Weighing Indicator 1 1 Feature l DESK type l Compact & Light Size l High Reliability & Durability l High Printing Speed & Clear printing condition l Various kinds of Columns can be selected - Print out with various format l Self testing Function l Hex Decimal Dumping mode - Check Data correction l Various graphic support function 1 2 Usage l Measuring Machine / System l Digital Weighing Indicator / Digital Scale l Factory Automation l Bill Issuing Machine / system l Parking Management System l Various kinds of Data Recordings. Chapter 2. Introduction 2 1 Specification Section Specification Type DESK TYPE Print method DOT IMPACT THERMAL COLUMNS 24/30/40 COLUMNS 24/32/36/42 COLUMNS * 24/30COL * 24/32COL Eng: 8x14, Kor: 16x14 Eng: 12x24, Kor: 24x24 Pont Size * 40COL * 36/42COL Eng: 6x12, Kor: 12x12 Eng: 9x24, Kor: 18x24 Pont English, Korean, Number. Symbols Dot/line 240 DOT / line 384DOT / line Print Speed 1.6line/sec 50mm/sec Cartridge EPSON ERC-09 - Paper 57mmx60mm ROLL PAPER Print Width 48.0mm Data Buffer 2Kbyte 8Kbyte RS-232C SERIAL Interface (BAND-RATE : 2400/9600/19200/115200bps Selectable) (Factory Preset) CENTRONICS PARALLEL Power DC +12 ~ 24V, 1.5A ( OPTION : AC adaptor 110V/220V) Dimension 110W(mm)x165D(mm)x85H(mm) 2 2 Control Panel Function Section Green LED ON-LINE Button RED LED FEED Button Function ON LINE condition Lamp l LED turns on When printer is ready l Under OFF condition, printer is not ready l Under blinking condition, it means no paper. Please, replace new paper ON-LINE/OFF-LINE button l Paper feeding is possible under ON-LINE button off, only. l All communication can be used under ON-LINE. (OFF-Line - No communication) Paper feeding lamp / Power lamp Power is connected to RED lamp is ON. Paper Feeding Button 3 4

3 2 3. Self Test Mode You can check Printer operation/condition through this function Self Test Mode will be done as follow Install paper with correction Under Power is on, press ON-LINE Button for 2~3sec. Then Self Test mode will be activated. When Self Test is done, printer will be stand by mode automatically Hex Decimal Dump Mode You can check the Data comes into the printer with correction or not. Also you can use this mode with software problem. Hex Decimal Dump Mode will be done as follow. Chapter 3. Connection 3 1 Serial Inter Face 1) Serial (RS-232C) Data Transmission Handshaking Signal Level Baud Rate Bit Length Parity Stop Bits Connector 2) Interface Connection Cable RS-232C Asynchronous DTR/DSR or XON/XOFF control MARK = -3 ~ -15V : 1 SPACE = +3 ~ +15V : /9600/19200/115200bps (Default : 9600bps) 8 bits None 1 Stop D-SUB 9 PIN MALE Install paper with correction Under Power is on, press ON-LINE Button for 2~3sec. Then Self Test mode will be activated. * 1 ~ 2 processes are all same with Self Test Mode Press ON LINE Button during Self Test Mode. After finishing Self Test, **[ HEX DUMP PRINT START ]** will be print out. Then, if you send data to the printer, all transferred data will be print out with Hex code 4 Hex Decimal Dump Mode will be dismissed when power is off 2 RXD RXD 2 3 TXD TXD 3 4 DTR 9Pin D-SUB Connector (FEMALE) Printer 5 GND GND 5 DSR 6 9 Pin D-SUB Connector (MALE) HOST l Under Handshaking is XON/XOFF, DSR/DTR Line is not needed l Under Paper End, send 0x07 signal twice, and Paper is normal condition, send 0x11(XON) 5 6

4 3) Connector pin specification and contents 1 STROBE DATA 1 ~ ACK 10 Pin No Signal Direction Contents 2 TXD Out Transfer Data 3 RXD In Receipt Data 6 DSR In l This signal informs that Host Device can be receipt data or not. l SPACE : Can be receipt Data l MARK : Can not be receipt Data l This signal will be operated by DSR/DTR Handshaking and Printer send Data after checking this signal l This signal will be used by Hardware Handshaking 7 GND - Signal Ground 20 DTR Out l This signal informs that Printer can be receipt data or not. l Under DTR/DSR control mode Space : Can be receipt Data MARK : Can not be receipt Data l Under Following condition, signal will be MARK. - Receipt Buffer is full - Under Printer Error - Under Self Test Mode 3 2 Parallel Inter Face 1) Centromics parallel Data Transmission Handshaking Connector 2) Interface connection cable 8-bit parallel STROBE and BUSY or ACK D-SUB 25 MALE 11 BUSY P..E E R R O R G N D µs(min) 0.5µs(min) 3) Connector pin specification and contents No Signal Direction Contents 1 /STROBE In l During reading the data, STROBE Pulse will be activated l Generally this signal is HIGH, but when the data reading under printer, the signal is LOW. 2~9 DATA 0 ~ 7 In l This signal is 8pcs data bit of Parallel Data l When detected HIGH signal will be 1, Low will be ACK Out l This signal informs that Printer can be receipt data. l Normally, the signal is High, under operation it is Low 11 BUSY Out l This signal informs that Printer can receipt data or not. l HIGH : Can not receipt data LOW : Can receipt data 12 PE Out l This signal informs that paper is ready or not. l HIGH : No Paper Low : Paper is ready 15 /ERROR Out l This signal informs that there is Error or not.. 18 GND - Signal Ground 4) Signal Timing Chart BUSY /ACK DATA /STB 5µs 5µs 25 Pin D-SUB Connector (FEMALE) Printer 25 Pin D-SUB Connector (MALE) HOST 7 8

5 3 3 Others Chapter 4. Dimension 1) Switch SW No. DOT type THERMAL type 1 2 Parity setting OFF OFF 9600bps * 9600 bps * ON OFF 19200bps bps OFF ON bps bps ON ON 2400bps 2400 bps 3 Korean mode setting OFF N.A N.A ON N.A N.A 4 Control Code Setting OFF INTERNAL * EPSON * ON EPSON CITIZEN 5 6 Columns setting OFF OFF 30 Columns * 32 Columns * ON OFF 40 Columns 42 Columns OFF ON 24 Columns 24 Columns ON ON 36 Columns 36 Columns 2) Jumper Definition (DOT/THERMAL) Jumper Status Contents J1 Open None Parity * Short Parity J2 Open Odd Parity Short Even Parity * Factory Preset l Power Connector Power Connector specification + DC +12V 1.5A G GND 9 10

6 Chapter 5. Command Mode 5 1. DOT Command (Basic) The basic command mode consists with IBM and EPSON command mode, so can be used with other printers Function type HEX Horizontality Tab HT $09 Print / Line Feed LF $0A Print / Carriage Return CR $0D Form Feed FF $0C Letter Width enlarge selection SO $0E Letter Width enlarge cancel SI $0F Letter Width enlarge cancel DC4 $14 Clear CAN $18 Printer Status inspection ESC BEL $1B $07 Under line mode set / delete ESC n $1B $2D n Line Interval setting ESC 1 n $1B $31 n Letter Pont #1(8x14) 30COL, set ESC 6 $1B $36 Letter Pont #2(6x12) 40COL set ESC 7 $1B $37 Letter Pont #1(8x14) 24COL set ESC 8 $1B $38 Covering Graphic ESC m n1 n2 nk CR $1B $27 m n1 n2 nk CR Printer Initialize $1B $40 Page Length Set ESC C n $1B $43 n Horizontality Tab position set ESC D n1 nk NUL $1B $44 n1 nk NUL Dot line Feed ESC J $1B $4A Graphic command ESC K n1 n2 d1 dk $1B $4B n1 n2 d1 dk Right Space set ESC Q n $1B $51 n Inverse image mode ESC R n $1B $52 n Letter Width enlarge selection ESC U n $1B $55 n Letter long enlarge selection ESC V n $1B $56 n Letter Width/long enlarge selection ESC W n $1B $57 n Transliterate selection ESC i n $1B $69 n Korean Printing mode selection ESC h n $1B $68 n Left Space set ESC l n $1B $6C n User letter definition ESC & m n1 n2 nk $1B $26 m n1 n2 nk User letter definition ESC % mn $1B $25 mn User letter definition ESC : $1B $3A 5-2 DOT Command (EPSON TM-U200 Command) Function Type HEX Horizontality Tab HT $09 Print / Line Feed LF $0A Print / Carriage Return CR $0D Printer status inspection ESC BEL $1B $07 Letter right interval setting ESC SP n $1B $20 n Print mode setting ESC! n $1B $21 n Absolute position setting ESC $ nl nh $1B $24 nl nh User definition letter set selection / ESC % n $1B $25 n cancel User letter definition ESC & y c1 cw [ ] $1B $26 y c1 cw [ ] Bit Image setting ESC * m nl nh d1 dk $1B $2A m nl nh d1.. Under line mode selection/cancel ESC n $1B $2D n Line interval selection(1/6inch) ESC 2 $1B $32 Line interval setting ESC 3 n $1B $33 n User letter definition cancel ESC? n $1B $3F n Printer Initialize $1B $40 Horizontality Tab position setting ESC D n1 nk NUL $1B $44 n1 nk NUL Emphasis mode selection ESC E n $1B $45 n Double strike mode selection/cancel ESC G n $1B $47 n Letter Pont selection ESC M n $1B $4D n Muti-languages selection ESC R n $1B $52 n Panel button activate mode ESC c 5 n $1B $63 $35 n Print / n line feed ESC d n $1B $64 n Koran printing mode selection ESC h n $1B $68 n Letter code table selection ESC t n $1B $74 n Inverse Image print mode selection ESC { n $1B $7B n Letter size selection GS! n $1D $21 n Printer ID transfer GS I n $1D $49 n 5 3 DOT Command (CITIZEN idp-3540 Command) Function Type HEX Print / Line Feed LF $0A Print / Carriage Return CR $0D N line paper Transfer FF n $0C n Letter width enlarge selection SO $0E Letter width enlarge cancel SI $0F Clear CAN $18 Initialize DC1 $11 Inverse letter mode DC2 $12 Printer status inspection ESC BEL $1B $07 Under line mode selection / cancel ESC n $1B $2D n Graphic Command ESC * n1 n2 d1 dk $1B $2A n1 n2 d1 dk Page length selection ESC C n $1B $43 n Feed composition ESC f $1B $66 Korean printing mode selection ESC h n $1D $68 n 11 12

7 5 4 Thermal Command(EPSON TM-88Ⅱ) Function type HEX Horizontality Tab HT $09 Print / Line Feed LF $0A Print / Carriage Return CR $0D Printer Status Inspection ESC BEL $1B $07 Letter right interval setting ESC SP n $1B $20 n Print mode setting ESC! n $1B $21 n Absolute position setting ESC $ nl nh $1B $24 nl nh User definition letter set selection / cancel ESC % n $1B $25 n User Letter definition ESC & y c1 cw[ ] $1B $26 y c1 cw[ ] Bit Image setting ESC * m nl nh d1 dk $1B $2A m nl nh d1.. Under line mode selection / cancel ESC n $1B $2D n Line interval selection(1/8inch) ESC 0 $1B $30 Line interval selection(1/6inch) ESC 2 $1B $32 Line interval setting ESC 3 n $1B $33 n Sub equipment setting ESC = n $1B #3D n User letter definition cancel ESC? n $1B $3F n Printer Initialize $1B $40 Horizontality Tab position set ESC D n1 nk NUL $1B $44 n1 nk NUL Emphasis mode selection ESC E n $1B $45 n Double strike mode selection/cancel ESC G n $1B $47 n Letter Pont selection ESC M n $1B $4D n Muti-languages selection ESC R n $1B $52 n Letter Rotation selection/cancel (90 degree, right direction) ESC V n $1B $56 n Relative Printer position setting ESC \ nl nh $1B $5C nl nh Function type HEX Panel button activate mode ESC c 5 n $1B $63 $35 n Print / n line feed ESC d n $1B $64 n Paper Full Cutting operate ESC i $1B $64 n Paper Partial Cutting operate ESC m $1B $69 Korean printing mode selection ESC h n $1B $68 n Letter code table selection ESC t n $1B $74 n Inverse Image print mode selection ESC { n $1B $7B n Letter size selection GS! n $1D $21 n Download Bit image definition GS*x y d11 d(x*y*8) $1D$2Axyd1 d(x*y*8) Download Bit image print GS / m $1D $2F m Printer ID transfer GS I n $1D $49 n Left margin setting GS L nl nh $1D $4C nl nh Printing Area setting GS W nl nh $1D $57 nl nh Printing Intensity setting GS g n $1D $67 n Bar Code Height setting GS h n $1D $68 n Bar Code Print Bit image print (Width direction) 1GS k m d1 dk NUL 2GS k m n d1 dn GS v 0 m xl xh yl yh d1 dk $1D $6B m d1...dk NUL $1D $6B m n d1 dn $1D $76 S30 m xl xh yl yh d1 dk Bar Code width setting GS w n $1D $77 n 13 14

8 5 5 THERMAL Command (CITIZEN idp-3540 Command) Function type HEX Print / Line Feed LF $0A Print / Carriage Return CR $0D N line paper Transfer FF n $0C n Letter Width enlarge selection SO $0E Letter Width enlarge cancel SI $0F Letter Width enlarge cancel DC4 $14 Printer Status Inspection ESC BEL $1B $07 Clear Command CAN $18 Initialize Command DC1 $11 Inverse Letter Mode DC2 $12 Inverse Letter selection / cancel ESC R n $1B $2A n1 n2 d1 dk Line interval selection(1/8inch) ESC 0 $1B $30 Line interval selection(1/6inch) ESC 2 $1B $32 Page length setting ESC C n $1B $43 n Feed composition command ESC f $1B $66 Cutting line skip command ESC N n $1B $4En Cutting line skip cancel command ESC O $1B $4F Letter Pont Selection ESC M n $1B $4Dn Korean printing mode selection ESC h n $1B $68 n Paper Full Cut command ESC P O $1B $50 $30 Paper Partial Cut command ESC P 1 $1B $50 $31 Printing Intensity setting GS g n $1D $67 n Printer ID transfer GS I n $1D $49 n Bar Code Height setting GS h n $1D $68 n Bar Code Print 1GS k m d1 dk NUL $1D $6B m d1...dk NUL 2GS k m n d1 dn $1D $6B m n d1 dn Bar Code width setting GS w n $1D $77 n 15

9 Manual Revision 1.4 SE 7300 SE7300 SD SE7300 PD SE7300 ST SE7300 PT PANEL TYPE CONTENTS 1. OUTLINE 1-1. FEATURE 1-2. APPLICATION 2. OPERATION 2-1. SPECIFICATION 2-2. EXPLANATION OF EACH OTHER 2-3. SELF-TEST 2-4. DUMP MODE 3. CONNECTIONS 3-1. SERIAL INTERFACE 3-2. PARRALL INTERFACE 3-3 THE OTHERS 4. OUTER APPEARANCE 4-1. SE7300 2

10 1.OUTLINE These printers are thermal method can be equipped in rack and stand alone on desk. for various data communication, POS terminal and various system. Prior to actual use, please read this instruction manual carefully for your correct understanding Feature l Ultra small-sized rack mounting thermal printing l Extremely light weight l High speed printing l Paper end detecting and auto loading l A little noise in printing l No ribbon type l Confirming to RS 232c and TTL and Parallel interface. l 24 and 32, 42 columns are available. l Self-test and Hex decimal (dump mode) applied l Graphic printing and bar code function are available APPLICATION l Instruments and inspection system l INDICATOR and scale l F. A. system l A receipt l POS SYSTEM l Parking system l Various data recording 2. OPERATION 2-1. SPECIFICATION ITEM SPECIFICATION DESIGN PANEL TYPE PRINT METHOD DOT Matrx MACHANISM COLUMNS 24/30/40 ON ENGLISH FONT SIZE 40COL ENGLISH: 6x12, KOREAN: 12x12 24/30COL ENGLISH: 8x14, KOREAN: 16x14 Cartridge Ribbon ERC-09,ERC-22 TOTAL DOTS 240 dots/line PRINT SPEED 1.6 Lines/Sec PRINT PAPER 57mmx50mm ROLL PAPER PRINT WIDTH 48.0mm DATA BUFFER 8Kbyte INTERFACE RS-232C SERIAL (BAUDRATE : 2400/9600/19200/115200bps selector) CENTRONICS PARALLEL INPUT POWER DC +12 ~ 24V, (1.5A ~2.0A) ( OPTION : External AC Adaptor 110V/220V) SIZE (mm) 119Wx89Dx130H 3 4

11 2-2. EXPLANATION EACH OTHER l FUNCTION OF SE7300 ITEM FUNCTION RED LED POWER INDICATOR. POWER ON, WHEN LIGHTING LAMP. GREEN LED INDICATOR ON-LINE l ON LINE (STANDBY PRINTING.) l LAMP OFF( NOT TO PRINT). l LED FLASHING, WHEN NO PAPER FEED S/W PRESS TO ADVANCE PAPER 2-3. SELF TEST The self test mode checks the printers control circuit function, setting parameter, software version, and printer quality. 3. CONNECTIONS 3-1. Serial interface 1) Serial(RS-232C) Data Transmission RS-232C Asynchronous Handshaking DTR/DSR or XON/XOFF control Signal Level MARK = -3 ~ -15V : 1 SPACE = +3 ~ +15V : 0 Baud Rate 9600/19200bps (Default : 9600bps) Bit Length 8 bits Parity None Stop Bits 1 Stop Connector D-SUB 25 FEMALE Before running the self -test, make sure there is sufficient paper. On pressing FEED S/W(SE7300), and power ON, starting the self-test. Printer becomes ready to receive data from the host. 2) Interface Connection 2 TXD TXD DUMP MODE Dump mode checks whether printer receives data correctly from the host or not Before running the self -test, make sure there is sufficient paper. On pressing FEED S/W(SE7300), and power ON, starting the self-test. After ending the self-test, continually press FEED S/W (SE7300), Then print **[ HEX DUMP PRINT START ]** after 2 seconds. Thought you don t touch any s/w, the printer take out HEXA mode changed data from host If power off, printer s recovered to normal mode 5 3 RXD RXD 3 66 DSR DSR 6 7 GND GND 7 20 DTR DTR Pin D-SUB Connector (MALE) Printer 25 Pin D-SUB Connector (FEMALE) HOST l Handshaking 이 XON/XOFF 시 DSR/DTR Line is not avalable. l On no paper, 0x07 has send on 2 times 2, and 0x11(XON) has send on refreshing paper. 6

12 3-2. Parallel interface 2 TXD 3 RXD 6 DSR 7 GND RXD 2 TXD 3 DTR 4 GND 5 DSR 6 1) Parallel Data Transmission Handshaking Connector 8-bit parallel STROBE and BUSY or ACK D-SUB 25 MALE 20 DTR 25 Pin D-SUB Connector (MALE) Printer 9 Pin D-SUB Connector (FEMALE) HOST 2) Interface Connection 1 STROBE DATA 1 ~ ) Interface Connector Pin SIG. DIRCTION FUNCTION 2 TXD OUT Transmitter data 3 RXD IN Receive data 6 DSR IN l Indicate Whether host could receive data or not. l Can do it on SPACE, not do it on MARK l Can operating on DSR/DTR Handshaking, printer transmitter data after checking the signal. l Use it on Hardware Handshaking. 7 GND - Signal Ground 20 DTR OUT l Indicate Whether printer could receive data or not. l Can do it on SPACE, not do it on MARK, when setting DTR/DSR control l It s on MARK as bellows - Full buffer in printer - Operating on error - On self-test 10 ACK BUSY P. E ERROR ~ 25 GND 18 ~ Pin D-SUB Connector (FEMALE) Printer 25 Pin D-SUB Connector (MALE) HOST 7 8

13 3) Interface Connector and function 4) Signal Timing Chart No SIGNAL DIR. FUNCTION 1 /STROBE IN l STROBE Pulse is occurred on reading data. l HIGH on normal, LOW on reading data 2 DATA0 IN 3 DATA1 IN 4 DATA2 IN 5 DATA3 IN 6 DATA4 IN 7 DATA5 IN 8 DATA6 IN 9 DATA7 IN l Parallel data bits l 1 on HIGH, 0 on LOW. 10 ACK OUT l Ready signal to receive data. l HIGH on normal, LOW on operatong. 11 BUSY OUT l Indicate Whether printer could receive data or not. l Can not receive on HIGH, can do it on LOW 12 PE OUT l Paper is or not l No paper on HIGH, set it on LOW. 13 SLCT OUT l Whether printer is ON-LINE or not. (NC) 14 /AUTO FD IN l 1Line space is advanced on auto-feed. (NC) 15 /ERROR OUT l Checking printer ERROR 16 /INIT IN l Hardware Reset in printer.(nc) 17 SLCT IN IN l Select printer on LOW. (NC) 18~25 GND - Signal Ground BUSY /ACK DATA /STB 0.5µs(min) 0.5µs(min) 5µs 5µs 9 10

14 3-3. THE OTHERS 4. OUTER APPARANCE 1) S/W CONNECTOR l SE7300 SW No. Define 1 2 Serial Baud Rate 4-1. SE7300 OFF OFF 9600 bps ON OFF bps OFF ON bps ON ON 2400bps 3 HanGul Type OFF WANSUNG ON JOHAP 4 Control Command ON EPSON OFF INTERNAL 5 6 Columns OFF OFF 30Columns ON OFF 40Columns OFF ON 24Columns ON ON 24Columns 7 8 Parity OFF OFF None Parity ON OFF Odd Parity ON ON Even Parity * Default mode on factory - out 2) POWER CONNECTOR CONNECTOR + DC +12V or 24V 1.5A G GND 11 12