NOTE FTDX9000 CAT OPERATION REFERENCE BOOK FTDX9000 OPERATING MANUAL
|
|
- Dylan Berry
- 5 years ago
- Views:
Transcription
1 NTE FTD9000 CAT PERATIN REFERENCE BK FTD9000 PERATING MANUAL
2 CAT (CMPUTER AIDED TRANSCEIVR) PERATIN VERVIEW The CAT (Computer Aided Transceiver) System in the FTD9000 provides control of frequency, VF, memory, and other settings such as dual-channel memories and diversity reception using an external personal computer. This allows multiple control operations to be fully automated as single mouse clicks or keystroke operations on the computer keyboard. The FTD9000 has a built-in level converter, allowing direct connection from the rear-panel CAT jack to the serial port of your computer without the need of any external boxes. You will need a serial cable for connection to the RS-232C (serial or CM port) connector on your computer. Purchase a standard serial cable (not the so-called null modem type), ensuring it has the correct gender and number of pins (some serial CM port connectors use a 9-pin rather than 25-pin configuration). If your computer uses a custom connector, you may have to construct the cable. In this case, refer to the technical documentation supplied with your computer for correct data connection. Vertex Standard does not produce CAT System operating software due to the wide variety of personal computers and operating systems in use today. However, the information provided in this chapter explains the serial data structure and opcodes used by the CAT system. This information, along with the short programming examples, is intended to help you start writing programs on your own. As you become more familiar with CAT operation, you can customize programs later on for your operating needs and discover the true operating potential of this system. CNTRL CMMAND A computer control command is composed of an alphabetical command, various parameters, and the terminator that signals the end of the control command. Example: Set the main band (VF-A) frequency to MHz. FA ; Command Parameter Terminator There is three for the FTD9000 Command as shown below: Set command: Set a particular condition (to the FTD9000) Read command: Reads an answer (from the FTD9000) Answer command: Transmits a condition (from the FTD9000) For example, note the following in the case of the FA command (Set the main band (VF-A) frequency): To set the main band (VF-A) frequency to MHz, the following command is sent from the computer to the transceiver: FA ; (Set command) To read the main band (VF-A) frequency, the following command is sent from the computer to the transceiver: FA; (Read command) When the Read command above has been sent, the following command is returned to the computer: FA ; (Answer command) CM 1 CAT RS-232C Straght Cable Page 1 FTD9000 PERATING MANUAL
3 CAT (CMPUTER AIDED TRANSCEIVR) PERATIN CNTRL CMMAND Alphabetical Commands A command consists of 2 alphabetical characters. You may use either lower or upper case characters. The commands available for this transceiver are listed in the PC Control Command Tables on the following pages. Parameters Parameters are used to specify information necessary to implement the desired command. The parameters to be used for each command are predetermined. The number of digits assigned to each parameter is also predetermined. Refer to the Control Command List and the Control Command Tables to configure the appropriate parameters. When configuring parameters, be careful not to make the following mistakes. For example, when correct parameter is IS (IF SHIFT): IS01000; Not enough parameters specified (No direction (+) given for the IF shift) IS0+100; Not enough digits (nly three frequency digits given) IS0_+_1000; Unnecessary characters between parameters IS ; Too many digits (Five frequency digits given) Note: If a particular parameter is not applicable to the FTD9000, the parameter digits should be filled using any character except the ASCII control codes (00 to 1Fh) and the terminator (;). Terminator To signal the end of a command, it is necessary to use a semicolon (;). The digit where this special character must appear differs depending on the command used. CNTRL CMMAND LIST CMMAND FUNCTIN SET READ ANS. AC AG AN BC BD BP BU BY CH CN CT DA DN DP FA FB FR FT GT IF IS KM KS KY LK MC MD MG ML MR MW Antenna Tuner Control AF GAIN Antenna Select Auto NTCH Status BAND DWN Manual NTCH Filter BAND UP BUSY Indicator Status Memory Channel Up/Down CTCSS Tone Frequency CTCSS Status Dimmer Set Microphone DWN Button TFT Display Set Main Band (VF-A) Frequency Sub Band (VF-B) Frequency Receiver Status Transmitter Status AGC Status Main Band (VF-A) Status IF SHIFT Keyer Memory Keyer Speed CW Keying DIAL Lock Status Memory Channel Set perating Mode MIC Gain Monitor Level Memory Channel Read Memory Channel Write FTD9000 PERATING MANUAL CMMAND FUNCTIN SET READ ANS. NB NL NR I S PA PB PC PL PR QI QR RC RD RG RL RT RU SC SD SH SM SQ T UL UP VD VG V T Noise Blanker Set Noise Blanker Level Noise Reduction Status Sub Band (VF-B) Status Repeater Shift IP Status Voice Memory Status T Power Level RF Speech Processor Level RF Speech Processor Status QMB Store QMB Recall R Clarifier ffset Clear R Clarifier Minus ffset RF Gain Noise Reduction Level R Clarifier Status R Clarifier Plus ffset SCAN Status CW Break-in Delay Time WIDTH Status S-meter Reading Squelch Level T Status PLL Unlock Status Microphone UP Button V Delay Time V Gain V Status T Clarifier Status Page 2
4 CAT (CMPUTER AIDED TRANSCEIVR) PERATIN CNTRL CMMAND TABLES AC Antenna Tuner Control A C ; A C ; A C ; AG AF GAIN A G P2 P2 P2 ; A G ; A G P2 P2 P2 ; 0: Tuner FF or Tuning Stop (While Tuner is engaged) 1: Start Antenna Tuning (While Tuner is engaged) 2: Tuning has failed (Answer only) 0: Main Band (VF-A) Receiver 1: Sub Band (VF-B) Receiver P AN Antenna Select A N P2 ; A N ; A N P2 ; BC Auto NTCH Status B C P2 ; B C ; B C P2 ; BD BAND DWN B D ; 0: Main Band (VF-A) 1: Sub Band (VF-B) P2 0: Auto Notch FF 1: Auto Notch N 0: Main Band (VF-A) 1: Sub Band (VF-B) 0: Main Band (VF-A) 1: Sub Band (VF-B) P2 0: No Change 1: Antenna 1 2: Antenna 2 3: Antenna 3 4: Antenna 4 5: Antenna R BP Manual NTCH Filter B P ; B P ; Answer B P ; BU BAND UP B U ; 000: Manual NTCH FF : NTCH Frequency (x10 Hz) 0: Main Band (VF-A) 1: Sub Band (VF-B) BY BUSY Indicator Status B Y ; B Y P2 ; CH Memory Channel Up/Down C H ; 0: Main Band (VF-A) BUSY FF 1: Main Band (VF-A) BUSY N P2 0: Sub Band (VF-B) BUSY FF 1: Sub Band (VF-B) BUSY N 0: Memory Channel UP 1: Memory Channel DWN Page 3 FTD9000 PERATING MANUAL
5 CAT (CMPUTER AIDED TRANSCEIVR) PERATIN CNTRL CMMAND TABLES CN CTCSS Tone Frequency C N P2 P2 ; C N ; C N P2 P2 ; CT CTCSS Status C T P2 ; C T ; C T P2 ; 0: Main Band (VF-A) 1: Sub Band (VF-B) P2 0-49: Tone Frequency Number (See Table 1) 0: Main Band (VF-A) 1: Sub Band (VF-B) P2 0: CTCSS FF 1: CTCSS ENC/DEC N 2: CTCSS ENC N DA Dimmer Set D A P2 P2 ; D A ; D A P2 P2 ; DN Microphone DWN Button D N ; P : TFT Backlight Brightness Level 00-15: Meter Brightness Level DP TFT Display Set D P ; D P ; D A ; 0: World Clock Display 1: Band Scope Display 2: AF scilloscope/spectrum Analyzer Display 3: Log Book Display 4: Temperature/SWR Display 5: Rotator Display 6: Memory Channel List Display FA Main Band (VF-A) Frequncy F A ; F A ; F A ; FB Sub Band (VF-B) Frequncy F B ; F B ; F B ; (Hz) (Hz) Hz 69.3 Hz 71.9 Hz 74.4 Hz 77.0 Hz 79.7 Hz 82.5 Hz 85.4 Hz 88.5 Hz Hz 94.8 Hz 97.4 Hz Hz Hz Hz Hz Hz Hz TABLE 1 (CTCSS TNE CHART) Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz FTD9000 PERATING MANUAL Page 4
6 CAT (CMPUTER AIDED TRANSCEIVR) PERATIN CNTRL CMMAND TABLES FR Receiver Status F R ; F R ; F R ; FT Transmitter Status F T ; F T ; F T ; GT AGC Status G T P2 ; G T ; G T P2 ; 0: Main Band (VF-A) Receiver: R, Sub Band (VF-B) Receiver: FF 1: Main Band (VF-A) Receiver: Mute, Sub Band (VF-B) Receiver: FF 2: Main Band (VF-A) Receiver: R, Sub Band (VF-B) Receiver: R 3: Main Band (VF-A) Receiver: Mute, Sub Band (VF-B) Receiver: R 0: Main Band (VF-A) Transmitter: T 1: Sub Band (VF-B) Transmitter: T 0: Main Band (VF-A) 1: Sub Band (VF-B) P2 0: AGC FF 1: AGC FAST 2: AGC MID 3: AGC SLW 4: AGC AUT IF Main Band (VF-A) Status I F ; I F P2 P2 P2 P2 P2 P2 P2 P2 P3 P4 P4 P4 P4 P5 P P7 P8 P ; Space (Fix) P2 VF-A Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift P4 Clarifier ffset: (Hz) P5 0: R CLAR FF 1: R CLAR N P6 0: T CLAR FF 1: T CLAR N P7 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U P8 0: VF 1: Memory P9 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC 0: Tone Number (See Table 1) 1 0: Simplex 1: Plus Shift 2: Minus Shift IS IF SHIFT I S P2 P3 P3 P3 P3 ; I S ; I S P2 P3 P3 P3 P3 ; KM Keyer Memory Set ~ 53 ** K M P2 P2 P2 P2 ~ P2 ; K M ; Answer ~ 53 ** K M P2 P2 P2 P2 ~ P2 ; KS Keyer Speed K S ; K S ; K S ; P2 P3 P2 0: Main Band (VF-A) 1: Sub Band (VF-B) Shift Direction +: Plus, --: Minus (Hz) (20 Hz multiple) 0-5 : Keyer Memory Channel Number Message Characters (up to 50 characters) (WPM) Page 5 FTD9000 PERATING MANUAL
7 CAT (CMPUTER AIDED TRANSCEIVR) PERATIN CNTRL CMMAND TABLES KY CW Keying K Y ; 1: Keyer Memory 1 Playback 2: Keyer Memory 2 Playback 3: Keyer Memory 3 Playback 4: Keyer Memory 4 Playback 5: Keyer Memory 5 Playback 6: Message Keyer 1 Playback 7: Message Keyer 2 Playback 8: Message Keyer 3 Playback 9: Message Keyer 4 Playback A: Message Keyer 5 Playback LK DIAL Lock Status L K ; L K ; L K ; 0: DIAL Lock FF 1: DIAL Lock N MC Memory Channel Set M C ; M C ; M C ; : Memory Channel Number : Regular Memory Channel 100: P-1L 101: P-1U ~ 116: P-9L 117: P-9U MD perating Mode M D P2 ; M D ; M D P2 ; MG MIC Gain M G ; M G ; M G ; ML Monitor Level M L ; M L ; M L ; 0: Main Band (VF-A) 1: Sub Band (VF-B) P2 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U MR Memory Channel Read M R ; M R P2 P2 P2 P2 P2 P2 P2 P2 P3 P4 P4 P4 P4 P5 P P7 P8 P ; Memory Channel Number P2 Memory Channel Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift P4 Clarifier ffset: (Hz) P5 0: R CLAR FF 1: R CLAR N P6 0: T CLAR FF 1: T CLAR N P7 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U P8 0: VF 1: Memory P9 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC 0: Tone Number (See Table 1) 1 0: Simplex 1: Plus Shift 2: Minus Shift FTD9000 PERATING MANUAL Page 6
8 CAT (CMPUTER AIDED TRANSCEIVR) PERATIN CNTRL CMMAND TABLES MW Memory Channel Write Memory Channel Number P2 Memory Channel Frequency (Hz) M W P2 P2 P2 P2 P2 P3 Clarifier Direction +: Plus Shift, --: Minus Shift P4 Clarifier ffset: (Hz) P5 0: R CLAR FF 1: R CLAR N P2 P2 P2 P3 P4 P4 P4 P4 P5 P6 P6 0: T CLAR FF 1: T CLAR N P7 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) P7 P8 P ; 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U P8 0: (Fixed) P9 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC 0: Tone Number (See Table 1) 1 0: Simplex 1: Plus Shift 2: Minus Shift NB Noise Blanker Status N B P2 ; N B ; N B P2 ; NL Noise Blanker Level N L P2 P2 P2 ; N L ; N L P2 P2 P2 ; NR Noise Reduction Status N R P2 ; N R ; N R P2 ; 0: Main Band (VF-A) Receiver 1: Sub Band (VF-B) Receiver P2 0: Noise Blanker FF 1: Noise Blanker N 2: Noise Blanker (Wide) N 0: Main Band (VF-A) Receiver 1: Sub Band (VF-B) Receiver P : Main Band (VF-A) Receiver 1: Sub Band (VF-B) Receiver P2 0: Noise Reduction FF 1: Noise Reduction N I Sub Band (VF-B) Status I ; I P2 P2 P2 P2 P2 P2 P2 P2 P3 P4 P4 P4 P4 P5 P P7 P8 P ; Space (Fix) P2 VF-B Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift P4 Crarifier ffset: (Hz) P5 0: R CLAR FF 1: R CLAR N P6 0: T CLAR FF 1: T CLAR N P7 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U P8 0: VF 1: Memory P9 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC 0: Tone Number (See Table 1) 1 0: Simplex 1: Plus Shift 2: Minus Shift S Repeater Shift S P2 ; S ; S P2 ; PA IP Status P A P2 ; P A ; P A P2 ; PB Voice Memory Status P B ; P B ; P B ; 0: Main Band (VF-A) Receiver 1: Sub Band (VF-B) Receiver P2 0: Simplex 1: Plus Shift 2: Minus Shift : FM mode only 0: Main Band (VF-A) Receiver 1: Sub Band (VF-B) Receiver P2 0: IP N (Pre-Amp Disable) 1: IP FF (Pre-Amp Enable) 0: Stop 1: Voice Message 1 Playback 2: Voice Message 2 Playback 3: Voice Message 3 Playback 4: Voice Message 4 Playback 5: Voice Message 5 Playback Page 7 FTD9000 PERATING MANUAL
9 CAT (CMPUTER AIDED TRANSCEIVR) PERATIN CNTRL CMMAND TABLES PC T Power Level P C ; P C ; P C ; PL RF Speech Processor Level P L ; P L ; P L ; PR RF Speech Processor Status P C ; P C ; P C ; : RF Speech Processor FF 1: RF Speech Processor N QI QMB Store Q I ; QR QMB Recall Q R ; RC R Clarifier ffset Clear R C ; RD R Clarifier Minus ffset R D ; (Hz) RG RF Gain R G P2 P2 P2 ; R G ; R G P2 P2 P2 ; RL Noise Reduction Level R L P2 P2 ; R L ; R L P2 P2 ; 0: Main Band (VF-A) Receiver 1: Sub Band (VF-B) Receiver P : Main Band (VF-A) Receiver 1: Sub Band (VF-B) Receiver P FTD9000 PERATING MANUAL Page 8
10 CAT (CMPUTER AIDED TRANSCEIVR) PERATIN CNTRL CMMAND TABLES RT R Clarifier Status R T ; R T ; R T ; 0: R Clarifier FF 1: R Clarifier N RU R Clarifier Plus ffset R U ; (Hz) SC SCAN Status S C ; S C ; S C ; SD CW Break-in Delay Time S D ; S D ; S D ; 0: Scan FF 1: Scan N (Upward) 1: Scan N (Downward) 0000: Full Break-in ms SH WIDTH Status S H P2 P2 ; S H ; S H P2 P2 ; P2 0: Main Band (VF-A) Receiver 1: Sub Band (VF-B) Receiver 00 (Counter Clockwise) - 31 (Clockwise), 16 (Center) SM S-meter Reading S M ; S M P2 P2 P2 ; SQ Squelch Level S Q P2 P2 P2 ; S Q ; S Q P2 P2 P2 ; T T Status T ; T M ; T ; UL PLL Unlock Status U L ; U L ; 0: Main Band (VF-A) S-meter 1: Sub Band (VF-B) S-meter P : Main Band (VF-A) Receiver 1: Sub Band (VF-B) Receiver P : RADI T FF CAT T FF 1: RADI T FF CAT T N 2: RADI T N CAT T FF 3: RADI T N CAT T N 0: PLL Lock 1: PLL Unlock Page 9 FTD9000 PERATING MANUAL
11 CAT (CMPUTER AIDED TRANSCEIVR) PERATIN UP Microphone UP Button U P ; CNTRL CMMAND TABLES VD V Delay Time V D ; V D ; V D ; ms (20 ms multiples) VG V Gain V G ; V G ; V G ; V V Status V ; V ; V ; T T Clarifier Status T ; T ; T ; : V FF 1: V N 0: T Clarifier FF 1: T Clarifier N FTD9000 PERATING MANUAL Page 10
12 Copyright 2005 VERTE STANDARD C., LTD. All rights reserved No portion of this manual may be reproduced without the permission of VERTE STANDARD C., LTD. Printed in Japan. FTD9000 PERATING MANUAL
CAT (COMPUTER AIDED TRANSCEIVER) OPERATION FT-450D CAT OPERATION YAESU MUSEN CO., LTD. FT-450D CAT OPERATION REFERENCE BOOK
CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FT-450D CAT PERATIN REFERENCE BK YAESU MUSEN C., LTD. FT-450D CAT PERATIN REFERENCE BK CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver)
More informationCAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FTD5000 SERIES CAT PERATIN REFERENCE BK FTD5000 SERIES CAT PERATIN REFERENCE CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver)
More informationCAT (COMPUTER AIDED TRANSCEIVER) OPERATION FT-950 CAT OPERATION FT-950 CAT OPERATION REFERENCE BOOK
CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FT-950 CAT PERATIN REFERENCE BK FT-950 CAT PERATIN REFERENCE BK CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver) System in the
More informationCAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FT-2000 SERIES CAT PERATIN REFERENCE BK FT-2000 SERIES CAT PERATIN REFERENCE BK CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver)
More informationCAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FT D 9000 SERIES CAT PERATIN REFERENCE BK FT D 9000 SERIES CAT PERATIN REFERENCE CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver)
More informationCAT Operation Reference Manual
CAT Operation Reference Manual YAESU MUSEN CO., LTD. Overview The CAT (Computer Aided Transceiver) System in the FT-99 transceiver provides control of frequency, VFO, memory, and other settings such as
More informationFT-891 YAESU MUSEN CO., LTD.
FT- CAT Operation Reference Book YAESU MUSEN CO., LTD. Overview The CAT (Computer Aided Transceiver) System in the FT- transceiver provides control of frequency, VFO, memory, and other settings such as
More informationFT-991. reference BOOk YAESU MUSEN CO., LTD.
FT- CAT OperATiOn reference BOOk YAESU MUSEN CO., LTD. Overview The CAT (Computer Aided Transceiver) System in the FT- transceiver provides control of frequency, VFO, memory, and other settings such as
More informationFTDX3000 SERIES CAT OPERATION REFERENCE BOOK YAESU MUSEN CO., LTD.
FTD3000 SERIES CAT PERATIN REFERENCE BK YAESU MUSEN C., LTD. CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver) System in the FTD3000 transceiver provides control of frequency,
More informationTS-590S TS-590SG. PC CONTROL COMMAND Reference Guide
TS-590S TS-590SG PC CONTROL COMMAND Reference Guide January/30/2019 PC CONTROL COMMAND REFERENCE GUIDE ABOUT THIS REFERENCE GUIDE All descriptions in this reference guide are for the user s convenience.
More informationSPECS FEATURES SUPPLIED ACCESSORIES. HF All Band Transceiver
718 HF All Band Transceiver RX 0.030-29.999999MHz* TX 1.800-1.999999 MHz** 3.500-3.999999 MHz** 7.000-7.300000 MHz 10.100-10.150000 MHz 14.000-14.350000 MHz 18.068-18.168000 MHz 21.000-21.450000 MHz 24.890-24.990000
More informationSERIAL INPUT AND SERIAL OUTPUT These ports are used for communications between the main CPU (controller) and the sub CPU.
IC-901 CPU SERIAL DATA CONTROL SERIAL INPUT AND SERIAL OUTPUT These ports are used for communications between the main CPU (controller) and the sub CPU. When the operation interrupt START BIT is applied
More informationThe amazing evolution of the 706 series
The amazing evolution of the 706 series The IC-706MKIIG carries on the 706 series tradition of base station performance and features in a mobile reg-sized package. Building on this legacy, frequency coverage
More informationBLOCK DIAGRAM - I J Li) N 6. w IS) AF D RIVE R R F D RIVE R R F P OWE R AMP PL L OSC UNIT. LL co X X X Lti X. C X W N O C..) 4 C.
MODEL 1-632 BLOCK DIAGRAM tl LL co a. LL O ox X X X X < X C.) W N C U) LL CO aa 1.11 t O - I J Ul Li) Lti N w IS) 1 X. C X Ir t AF D RIVE R X - LL C.) CD r.--1111 MOP U) N N 6 PL L OSC UNIT R F D RIVE
More informationIcom IC-9100 HF/VHF/UHF transceiver
263 Walsall Road, Great Wyrley, Walsall, WS6 6DL Established 1997. Open Monday - Friday 9am - 5pm and Saturday 9.30am - 4pm Tel: 01922 414 796 Fax: 01922 417829 Skype: radioworld_uk Icom IC-9100 HF/VHF/UHF
More informationFT-897 Alignment. Local Oscillator Adjustment. PLL Adjustment
FT-897 Local Oscillator Adjustment Reference Frequency Adjustment a. Connect a frequency counter to TP1032. b. Adjust the trimmer capacitor (TC5001) for 67.875000MHz ±5Hz on the frequency counter. c. Connect
More informationElmer Session Hand Out for 3/3/11 de W6WTI. Some Common Controls Found On Amateur Radio Transceivers. (From ARRL web site tutorial)
Elmer Session Hand Out for 3/3/11 de W6WTI Some Common Controls Found On Amateur Radio Transceivers. (From ARRL web site tutorial) The placement of the controls may vary from manufacturer to manufacturer
More informationFrequency Coverage MHz RF Power Output 30W SSB / 9W AM/ 30W FM Dual Finals on Heat Sink Modes AM, FM, USB, LSB Microprocessor
MAGNUM M-257 30W AM/ /FM/SSB 10--11 Meterr Mobile Trranscei ivverr n Prri iiccee: : US$ 250..00 eexx ssttoocckk JJaakkaarrttaa (Arrrri ( iivvi iinngg 2 d weeeekk iinn i Maarrcchh) ) SPECIFICATIONS Frequency
More informationTI RigExpert. User s manual. USB Transceiver Interface
TI-5000 RigExpert USB Transceiver Interface User s manual . Table of contents Introduction Operating the TI-5000 Front and rear panels Transceiver and computer connection Updating the firmware Annexes
More informationThe Icom IC Adam Farson VA7OJ. A New Top-class HF/6m Transceiver. IC-7700 Information & Links
The Icom IC-7700 A New Top-class HF/6m Transceiver Adam Farson VA7OJ IC-7700 Information & Links Copyright 2008 North Shore Amateur Radio Club NSARC HF Operators IC-7700 1 IC-7700 front panel This is a
More informationRigExpert TI-7 USB Transceiver Interface User s manual
RigExpert TI-7 USB Transceiver Interface User s manual Please read this manual before attempting to use the RigExpert TI-7 device. - - 2 - Table of contents 1. What is a RigExpert TI-7?... 4 2. Specifications...
More informationTechnician License Course Chapter 5. Lesson Plan Module 11 Transmitters, Receivers and Transceivers
Technician License Course Chapter 5 Lesson Plan Module 11 Transmitters, Receivers and Transceivers Generalized Transceiver Categories Mobile Single Band Dual Band All Band Multimode Handheld (HT) VHF/UHF
More informationDELUXE 18CHANNEL SSB/AM CB TRANSCEIVER OWNER'S GUIDE
DELUXE 18CHANNEL SSB/AM CB TRANSCEIVER OWNER'S GUIDE General Description The Bush Ranger is a combination transmitter and receiver designed for use in the Australian 27 MHz Citizens radio service. It is
More informationOperation Manual. SlJPER ST AR Channel Mobile 5-Mode Transceiver -----~- --:.. KTSS200NXX ,, I
Operation Manual!.,, SlJPER ST AR 2000 200 Channel Mobile 5-Mode Transceiver -----~- --:.. KTSS200NXX General Description l Frequency/Channel Chart The Super Star -2000 is a combination transmitter-receiver
More informationSUBELEMENT T4. Amateur radio practices and station set up. 2 Exam Questions - 2 Groups
SUBELEMENT T4 Amateur radio practices and station set up 2 Exam Questions - 2 Groups 1 T4A Station setup: connecting microphones; reducing unwanted emissions; power source; connecting a computer; RF grounding;
More informationIC-F7000. Advanced selective call and ALE make HF communication easier than ever!
Page 1 of 5 HF TRANSCEIVER IC-F7000 Advanced selective call and ALE make HF communication easier than ever! The IC-F7000 is an HF land mobile transceiver especially designed forlong distance communications.
More informationMidland 248XL I NSTRUCTION GUI DE
Midland 248XL I NSTRUCTION GUI DE INDEX Introduction...2 Function and location of the controls...3 Installation...7 Power supply...7 Installing an antenna...7 How to use your Midland 248XL...8 Frequency
More informationLnR Precision, Inc. 107 East Central Avenue, Asheboro, NC
LD5 CW/SSB QRP Transceiver Quick guide manual Description: At the development base of the digital signal processing unit, an algorithm is embedded for IQ processing of the channels with phase suppression
More informationGRAND STRAND AMATEUR RADIO CLUB
The GRAND STRAND AMATEUR RADIO CLUB (GSARC) Myrtle Beach SC is offering used amateur related equipment for sale. Written bids may be submitted to the GSARC up to Friday, November 23 rd, 2018. Only currently
More informationFT-991 Firmware Update Information
FT-991 Firmware Update Information This update adds the DG-ID function and the DP-ID function in the digital C4FM mode of the FT- 991 and is compatible with the System Fusion II digital repeater DR-2X.
More informationCI-V REFERENCE GUIDE. HF/50MHz TRANSCEIVER. i7610
CI-V REFERENCE GUIDE HF/50MHz TRANSCEIVER i7610 Table of contents Remote control 2 Remote control (CI-V) information 2 DDCI-V connection 2 DDPreparing 2 DDAbout the data format 2 DDCommand table 3 DDCommand
More informationSEA 235 OPERATOR S MANUAL Digital Single Sideband Radiotelephone
SEA 235 OPERATOR S MANUAL Digital Single Sideband Radiotelephone TABLE OF CONTENTS GENERAL OPERATIONS...1 TECHNICAL SPECIFICATIONS...1 GENERAL INFORMATION...2 UNDERSTANDING CHANNEL MEMORY...3 LCD DISPLAY
More informationLD5 CW/SSB QRP Transceiver SDR /DSP
LD5 CW/SSB QRP Transceiver SDR /DSP Quick guide manual Description: At the development base of the digital signal processing unit, an algorithm is embedded for IQ processing of the channels with phase
More informationTHEORY OF OPERATION. TM308EUL for Cobra Nov 06,2006
THEORY OF OPERATION TM308EUL for Cobra Nov 06,2006 This PLL controlled VHF marine mobile transceiver provides an accurate and stable multi-channel operation. The transceiver consists of 15 main sections
More informationINSTRUCTION MANUAL REMOTE CONTROL SOFTWARE RS-R75
INSTRUCTION MANUAL REMOTE CONTROL SOFTWARE RS-R75 IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the receiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains important
More informationPushing performance to the pinnacle
Pushing performance to the pinnacle The latest DSP technologies developed for the IC-7800/7700 plus over 45 years of analog circuit expertise give the IC-7600 the performance advantage. The flagship's
More informationFT-991 MENU MODE. changes in factory defaults are yellow
changes in factory defaults are yellow FT-991 MENU MODE No. Menu Function Available Settings Default Value 001 AGC FAST DELAY 20-4000 (20msec/step) 300msec 002 AGC MID DELAY 20-4000 (20msec/step) 700msec
More informationKenwood TH-G71 Protocol Specification
Kenwood TH-G71 Protocol Specification This document describes the serial commands used to program and control the TH-G71 radio via its serial port. Some of this data was initially based on information
More informationAM/FM/SSB/CW 12 & 10 METER MOBILE AMATEUR TRANSCEIVER OWNER S MANUAL
AM/FM/SSB/CW 12 & 10 METER MOBILE AMATEUR TRANSCEIVER OWNER S MANUAL TABLE OF CONTENTS Warranty...2 Introduction...3 Installation... 4-5 Front Panel Controls... 6-8 Microphone...8 Menu Settings... 9-11
More informationTS-890S. PC CONTROL COMMAND Reference Guide
TS-890S PC CONTROL COMMAND Reference Guide August/30/2018 PC CONTROL COMMAND REFERENCE GUIDE ABOUT THIS REFERENCE GUIDE All descriptions in this reference guide are for the user s convenience. JVC KENWOOD
More informationCode Master. Model CWR-610E OPERATING INSTRUCTIONS
Code Master Model CWR-610E OPERATING INSTRUCTIONS CONTENTS RATING... 3 DESCRIPTION OF PANELS... 5 METHOD OF USE Preparation... 7 Reception of CW... 7 Code interpretable range and word space... 7 Reception
More informationApplication for FCC / IC FCC ID: K X50 IC: 511B HF/50 MHz Transceiver FT-410 Operation Manual YAESU MUSEN CO., LTD. Tennozu Parkside Build
HF/50 MHz Transceiver FT-410 Operation Manual YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress, CA 90630,
More informationYoukits SK-1A 40m SSB/CW QRP Transceiver. Operating manual
Youkits SK-1A 40m SSB/CW QRP Transceiver Operating manual Specifications Size: 88*38*124mm (not including knob, etc.) Weight: about 280g (not including battery pack) Supply voltage: 10-15VDC Current drain
More informationKENWOOD SKY COMMAND SYSTEM
KENWOOD SKY COMMAND SYSTEM Operation Manual KENWOOD COMMINICATIONS CORPORATION KENWOOD COMMUNICATIONS CORPORATION This operation manual is used for the KENWOOD SKY COMMAND SYSTEM (hereinafter referred
More informationFT-991. HF/VHF/UHF All Mode Transceiver
HF/VHF/UHF All Mode Transceiver FT-991 Operating Manual YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress,
More informationAdjustment for IC-910H. Adjustment. Adjustment
for IC-910H 30.2 MHz Level 430MHz 2 nd Lo (60.4MHz) Peak Setting the 60.4MHz Frequency the144mhz 1 st Lo Lock Voltage th430mhz 1 st Lo Lock Voltage 144MHz RX Peak/ Gain Band Peak Band Total Gain Sub- Band
More informationUser Manual. Specifications...3. Control and Operation Microphone...8. Installation...9. Installation of Main Unit...9
Contents Specifications...3 Control and Operation...4-7 Microphone...8 Installation...9 Installation of Main Unit...9 Antenna Installation...9 Operational test...9 Frequency Bands Table...10 Frequency
More informationINSTALLATION AND CONNECTIONS Section 2
STLLTION ND CONNECTIONS Section Unpacking - ntenna jumper cable connection - Selecting a location - Rack mounting handle attachment - Grounding -3 ntenna connection -3 CF (Compact Flash) memory card -3
More informationDX AM FM SSB CW PA Amateur Base Station Transceiver OWNER S MANUAL RX / TX 2 4 POWER NF CHANNEL MODE RF POWER OFF CAL OFF OFF CALIBRATE
1 2 3 6 4050 ULA 6070 TI 80 90 100 9 DX 2517 2517 RX / TX 0 2 4 SWR WATTS SET 81012 22 1 010 3 2030 5 MOD 7 ON dbover 9 SIGNAL +20 +40+60 PA FM AM USB LSB CW POWER ON SWR NB / ANL R.BEEP +10KHz NF CHANNEL
More informationELAD FDM-DUO Dual Mode SDR Transceiver USER MANUAL
ELAD FDM-DUO Dual Mode SDR Transceiver USER MANUAL www.eladit.com Contents Revision History... 4 1 Overview... 5 1.1 Notice... 5 1.2 Firmware versions... 5 1.3 Introduction... 5 1.3.1 Main Features...
More informationi2820h (USA) ie2820(europe)
January 2007 DUAL BAND TRANSCEIVERS i2820h (USA) ie2820(europe) The above photo shows the IC-2820H. The IC-E2820 differs slightly from this photo. Icom proudly announces the debut of the new dual band
More informationUser s Manual. MegaJet Downloaded from Mobile CB Radio Station FM CITIZENS BAND TRANSCEIVER
User s Manual MegaJet - 900 Mobile CB Radio Station FM CITIZENS BAND TRANSCEIVER Downloaded from www.cbradio.nl Feature List of MJ-900 1. It incorporate all functions of two-way radios being sold in the
More informationTransceiver selection and Specs.
Transceiver selection and Specs. Transceivers 1956-2018 From TUBES to SDR Covers 20-10 meters in 100Khz segments, 10 available, crystal needed for each. Plug in crystal holder. 100 Watts output, final
More informationIC-400pro - RADIOAFICION.COM
PROCEDURES IC-400pro - 5- PREPARATION When you adjust the contents on pages 5-5 and 5-6, SOFT- WARE, the optional CS-400PRO ADJ SOFTWARE (Rev..0 or later), *OPC- JIG CABLE (modified OPC- CLONING CABLE;
More informationmicro KEYER II and WriteLog Setup
Router setup: micro KEYER II and WriteLog Setup Note: The absolute port numbers do not matter. The key is consistency - the same port number must be used for a specific function every time it is used.
More informationCat. No OWNER S MANUAL. HTX-212 Two-Meter Mobile Transceiver. Please read before using this transceiver.
19-1125.fm Page 1 Tuesday, August 3, 1999 9:47 AM Cat. No. 19-1125 OWNER S MANUAL HTX-212 Two-Meter Mobile Transceiver Please read before using this transceiver. 19-1125.fm Page 2 Tuesday, August 3, 1999
More informationHF/VHF/UHF ALL MODE TRANSCEIVER FT-818
HF/VHF/UHF ALL MODE TRANSCEIVER FT-818 Operating Manual Contents Introduction...1 Accessories & Options...2 Supplied Accessories...2 Available Options...2 Plug Pinout...3 Installation...4 Connecting the
More informationi78 INSTRUCTION MANUAL HF TRANSCEIVER
INSTRUCTION MANUAL HF TRANSCEIVER i78 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
More informationHF/50MHz TRANSCEIVER
HF/50MHz TRANSCEIVER D isplay Pushing performance to the pinnacle The latest DSP technologies developed for the flagship models plus many decades of analog circuit expertise give the the performance advantage.
More informationApplications: FM wireless audio, USB PC audio broadcasting, wireless microphones, maternal and child care.
Product Description 1: The use of advanced digital audio signal processing (DSP) technology and FM modulation phase-locked loop (PLL) to make sound more realistic, more stable performance, long working
More informationBAND DECODER and CONTROLLE R. Accessibility Upgrade and Operating Instructions
ELE CRAFT KRC2 BAND DECODER and CONTROLLE R Accessibility Upgrade and Operating Instructions Revision A, March 4, 2004. Copyright 2004, Elecraft; All Rights Reserved Introduction The KRC2 Accessibility
More informationINSTRUCTION MANUAL IP REMOTE CONTROL SOFTWARE RS-BA1
INSTRUCTION MANUAL IP REMOTE CONTROL SOFTWARE RS-BA FOREWORD Thank you for purchasing the RS-BA. The RS-BA is designed to remotely control an Icom radio through a network. This instruction manual contains
More informationmicro KEYER and N1MM Logger+ Setup
micro KEYER and N1MM Logger+ Setup Router setup: Note: The specific port numbers are not important. The key is consistency - the same port number must be used for a specific function in both Router and
More informationi7610 Technical Report Volume 1
i7610 Technical Report Volume 1 ~ Profile ~ Outstanding HF Experience Right Here Icom s mid class HF transceivers evolved especially with the IC-756, IC- 756PRO and IC-7600, and were technology leaders
More informationCAT-700B Repeater Controller Computer Automation Technology, Inc
CAT-00B Repeater Controller Computer Automation Technology, Inc N.W. st Avenue, Suite Fort Lauderdale, Florida 0 Phone: () 8- Fax: () 88-8 Internet: http://www.catauto.com Table of Contents Chapter Page.
More informationi7610 Technical Report Volume 1
i7610 Technical Report Volume 1 ~ Profile ~ Outstanding HF Experience Right Here Icom s mid class HF transceivers evolved especially with the IC-756, IC756PRO and IC-7600, and were technology leaders in
More informationICOM IC-R8600 Specifications, Features & Options
General Frequency coverage IC-R8600 USA: 0.010000 821.999999MHz*, 851.000000 866.999999MHz, 896.000000 3000.000000MHz (*Guaranteed range: 0.100000 821.999999MHz) Antenna connector Frequency stability Mode
More informationVvV MODEL-309 OWNER'S MANUAL. 40 channel CB Transceiver. Professional Quality And Performance Standards Advanced Circuitry With PLL Synthesis
VvV MODEL-309 OWNER'S MANUAL 40 channel CB Transceiver Professional Quality And Performance Standards Advanced Circuitry With PLL Synthesis GENERAL INSTRUCTIONS Your model is an all solid-state SSB/AM
More informationINSTRUCTION MANUAL. HF/ 50 MHz ALL MODE TRANSCEIVER TS-590S
INSTRUCTION MANUAL HF/ 50 MHz ALL MODE TRANSCEIVER TS-590S NOTIFICATION This equipment complies with the essential requirements of Directive 1999/5/EC. The use of the warning symbol means the equipment
More informationRMV25 / RMV50 RMU25 / RMU45
RMV25 / RMV50 RMU25 / RMU45 Owner's Manual TABLE OF CONTENTS INTRODUCTION... 3 FCC Requirements... 3 SAFETY WARNING INFORMATION... 3 CONTROLS and INDICATORS... 5 FRONT PANEL... 5 LCD Icons and Indicators...
More informationMOTOROLA COMMERCIAL SERIES BASIC USER GUIDE CM140 & CM160
MOTOROLA COMMERCIAL SERIES BASIC USER GUIDE CM140 & CM160 11 1 2 4 10 CHAN 34 P1 P2 P3 P4 11 8 3 5 6 7 10 9 English BASIC USER GUIDE Contents RadioOverview... 2 Radio Controls...................... 2 Microphone
More informationSecond Hand Yaesu FTDX5000MP HF base station transceiver
263 Walsall Road, Great Wyrley, Walsall, WS6 6DL Established 1997. Open Monday - Friday 9am - 5pm and Saturday 9.30am - 4pm Tel: 01922 414 796 Fax: 01922 417829 Skype: radioworld_uk Second Hand Yaesu FTDX5000MP
More informationTS-590S INSTRUCTION MANUAL. HF/ 50 MHz ALL MODE TRANSCEIVER
INSTRUCTION MANUAL HF/ 50 MHz ALL MODE TRANSCEIVER TS-590S NOTIFICATION This equipment complies with the essential requirements of Directive 1999/5/EC. The use of the warning symbol means the equipment
More informationYaesu FT-991A HF, VHF, and UHF Transceiver
Mark J. Wilson, K1RO, k1ro@arrl.org Product Review Yaesu FT-991A HF, VHF, and UHF Transceiver Reviewed by Joel R. Hallas, W1ZR QST Contributing Editor w1zr@arrl.org The FT-991A is a compact SSB, CW, AM,
More informationE L E C R A F T K 2 R E V I S I O N 2 F I R M W A R E
E L E C R A F T K 2 R E V I S I O N 2 F I R M W A R E Installation and Reference Manual Rev. B, August 28, 2001 Summary of Changes... 2 Computer Control (KIO2)... 2 Transverter Bands... 2 RTTY/Data Mode
More informationChapter 15: Serial Controlled (HF) Radio Support
15-1 Chapter 15: Serial Controlled (HF) Radio Support This section describes the controller's interface for serial controlled radios. Most such radios are for the HF bands, but some such as the FT-736
More informationJUMA-TRX2 DDS / Control Board description OH2NLT
JUMA-TRX2 DDS / Control Board description OH2NLT 22.08.2007 General Key functions of the JUMA-TRX2 DDS / Control board are: - provide user interface functions with LCD display, buttons, potentiometers
More informationWIRES-X Portable Digital Node Function. Instruction Manual
Wide-Coverage Internet Repeater Enhancement System WIRES-X Portable Digital Node Function Instruction Manual Please read this Instruction Manual carefully for appropriate procedure. Preparation Procedure
More informationWIRES-X Portable Digital Node Function. Instruction Manual
Wide-Coverage Internet Repeater Enhancement System WIRES-X Portable Digital Node Function Instruction Manual Please read this Instruction Manual carefully for appropriate procedure. Preparation Procedure
More informationINSTRUCTION MANUAL VHF/UHF ALL MODE TRANSCEIVER. i910h
INSTRUCTION MANUAL VHF/UHF ALL MODE TRANSCEIVER i910h IMPORTANT EXPLICIT DEFINITIONS READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the transceiver. SAVE THIS INSTRUCTION MANUAL. This
More informationDisable Windows Sounds
9/28/2017 - K3CT Disable Windows Sounds Users may want to disable the Windows Sounds so none of the Windows OS sounds are transmitted on the radio. Install the Icom Drivers, Select COM port, Disable Power
More informationI.D.A. Operation manual
TRX-200 Wide ide Band Receiver Operation manual Thank you for purchasing the TRX-200 all modes wide band monitoring receiver. Please read this operating manual carefully to avoid miss operation of the
More informationHR MHZ AM-FM AMATEUR RADIO HF TRANSCEIVER OWNER'S MANUAL. Content of the packaging
HR-2800 28 MHZ AM-FM AMATEUR RADIO HF TRANSCEIVER OWNER'S MANUAL NOTICE! It is recommended to carefully read this owner s manual before using the product. This will also help to prevent illegal use of
More informationTesting Motorola P25 Conventional Radios Using the R8000 Communications System Analyzer
Testing Motorola P25 Conventional Radios Using the R8000 Communications System Analyzer Page 1 of 24 Motorola CPS and Tuner Software Motorola provides a CD containing software programming facilities for
More informationAM/FM 10 METER MOBILE AMATEUR TRANSCEIVER OPERATING MANUAL
AM/FM 10 METER MOBILE AMATEUR TRANSCEIVER OPERATING MANUAL INTRODUCTION Congratulations on your purchase of a Magnum S-6 AM/FM 10 meter transceiver. Your Magnum S-6 is designed to provide years of enjoyment
More informationFT-450 OPERATION MANUAL HF/50 MHZ TRANSCEIVER
HF/50 MHZ TRANSCEIVER FT-450 OPERATION MANUAL VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A.
More informationmat-30 HF-SSB Automatic Antenna Tuner Instruction Manual Version V1.0
INTRODUCTION mat-30 HF-SSB Automatic Antenna Tuner Instruction Manual Version V1.0 The mat-30 is an automatic tuner intended for use with modern Yaesu transceivers. It works with some Yaesu transceiver
More informationBUXCOMM 2007 RASCAL GLX OPERATOR S MANUAL Before we begin, let s perform the initial setup:
BUXCOMM 2007 RASCAL GLX OPERATOR S MANUAL Before we begin, let s perform the initial setup: Sound Card CONFIGURATION: Most soundcards use 3.5mm (1/8") jack for line and/or microphone input. Use the LINE
More informationBefore using your FT-950, be sure to read and follow the instructions in the Before You Begin section of this manual.
About This Manual... The FT-950 is a leading-edge transceiver with a number of new and exciting features, some of which may be unfamiliar to you. In order to gain the most enjoyment and operating efficiency
More informationIcom IC A Look Under the Hood Bruce Wampler - WA7EWC
Icom IC-7300 A Look Under the Hood Bruce Wampler - WA7EWC The Icom IC-7300 is a brand new (April 2016), Direct Conversion, 100% SDR. It is the first SDR amateur radio transceiver by one of the major Japanese
More informationTHE TRANSCEIVER Instruction Manual
THE TRANSCEIVER i7800 Instruction Manual A-6328H-1EX-q Printed in Japan 2004 Icom Inc. FOREWORD Congratulations! You are the owner of the world s most advanced amateur HF/50 MHz transceiver IC-7800. The
More informationINSTRUCTION MANUAL ALL MODE MULTI-BAND TRANSCEIVER TS-2000 TS-2000X TS-B2000
B6--50 (K, E) 09 08 07 06 05 ALL MODE MULTI-BAND TRANSCEIVER TS-000 TS-000X TS-B000 INSTRUCTION MANUAL NOTIFICATION This equipment complies with the essential requirements of Directive 999/5/EC. The use
More informationPeerless Performance TS-590S. HF / 50 MHz ALL MODE TRANSCEIVER
Peerless Performance TS-590S HF / 50 MHz ALL MODE TRANSCEIVER Discovering the Hidden The TS-590S marks a bold new chapter in Kenwood s proud history of high-performance HF transceivers. Featuring a narrow-band
More informationIcom IC-7851 HF & 50MHz transceiver
Icom IC-7851 HF & 50MHz transceiver A new flagship is born: the current market leader in terms of performance 36 PHOTO 1: IC-7851 front view. INTRODUCTION. In 2004, Icom launched their IC-7800 top-of-the-range
More informationRack Mount Repeater VXR-9000E. Operating Manual. Vertex Standard LMR, Inc.
Rack Mount Repeater VXR-9000E Operating Manual Vertex Standard LMR, Inc. Introduction The VXR-9000E is commercial-grade 25-watt FM repeater designed to provide reliable two-way full-duplex communications
More informationMC-80 TERMINAL INTERFACES
DATA COMMUNICATOR 144/440MHz FM Dual Bander One of the greatest pleasures of exploration is being able to communicate each new discovery. And Kenwood s Data Communicator allows you to do just that. This
More informationB & D Enterprises 1P repeater controller pg 1 INTRODUCTION:
B & D Enterprises 1P repeater controller pg 1 INTRODUCTION: The 1P is a basic repeater controller. The controller uses low power devices and stores all commands and system status in non-volatile EE prom.
More information18-CHANNEL MOBILE CB TRANSCEIVER MODEL CB-845
18-CHANNEL MOBILE CB TRANSCEIVER MODEL CB-845 INSTRUCTION HANDBOOK RAll JEFFERSOn CITIZEN BAND RADIO MESSAGE TO THE OWNER CONGRATULATIONS! As the new owner of Ray Jefferson Model CB-845 CB Mobile Transceiver,
More informationYaesu FT-8800R Alignment
DUAL BAND FM TRANSCEIVER Introduction and Precautions The FT-8800R has been carefully aligned at the factory for the specified performance across the 144 MHz and 430 MHz amateur bands. Realignment should
More informationAmateur Station Control Protocol (ASCP) Ver Oct. 5, 2002
Amateur Station Control Protocol (ASCP) Ver. 0.17 Oct. 5, 2002 Moe Wheatley, AE4JY Table of Contents 1. Purpose...4 2. Basic Protocol Concepts...5 3. Message Block Format...8 3.1. Detailed Description
More information