SECTION GARBAGE CHUTE. Wilkinson Chutes Canada Toronto, Ontario, CANADA
|
|
- Collin Campbell
- 6 years ago
- Views:
Transcription
1 Version 00 WILKINSON HUTES ANADA PAGE OF This section is based on a system produced by: Part GENERAL RELATED DOUMENTS - GARAGE HUTE Wilkinson hutes anada Toronto, Ontario, ANADA -- A The general provisions of the contract, including General and Supplementary onditions and Division, General Requirements, apply to the work specified in this section DESRIPTION OF WORK A Work Included: Furnish and install where shown on plans inch (00 mm) diameter trash chute as manufactured by Wilkinson hutes anada as specified below SUMITTALS A atalog uts: efore the trash chute is delivered to the job site, submit catalog cuts to the Architect in accordance with these specifications, showing all details of installation and assembly and all requirements for work by other trades Product Data: Manufacturer s product specifications, standard details and recommendations for project conditions; indicate selected sizes and installation details specific to the project Shop Drawings: : Plans: Scale mm to 00 mm; indicate locations, dimensions, and required associated construction activities : Elevations/Sections: Scale mm to 00 mm; indicate locations, dimensions, and required associated required construction activities : Details: Scale mm to 00 mm; indicate: a Shop drawings specific to project conditions b Interface with adjacent construction c Dimensions and tolerances d Products required for installation of the trash chute, but not supplied by the equipment manufacturer WILKINSON HUTES ANADA Telephone: -- / Fax: --
2 Version 00 WILKINSON HUTES ANADA PAGE OF D Quality Assurance/ontrol Submittals: ontractor s ertification that: a) Products of this section are manufactured by Wilkinson hutes anada, as distributed by Wilkinson hutes anada b) Manufacturer s certification that installer of manufacturer s product is approved c) Applicable standards: National Fire Protection Association (NFPA/8), and the Ontario uilding ode standards as referenced herein E lose-out Submittals: Operation and Maintenance Data: a) Manufacturer s printed Operation Manual Warranty Documents: Issued and executed by the manufacturer and installer of the system QUALITY ASSURANE A Qualifications: Manufacturer: Minimum five () years-documented experience producing products specified in this section Installer: Approved by the Manufacturer, and having a minimum of five () years experience Pre-Installation Meetings: onvene at job site a minimum of seven () calendar days prior to scheduled beginning of construction activities of this section to review requirements of this section Require attendance by representatives of the following: a Trash chutes manufacturer or designated representative b Installer of this section c Other entities directly affecting, or affected by, construction activities of this section d Notify Architect four () calendar days in advance of scheduled meeting date RELATED WORK Y OTHERS SPEIFIED ELSEWHERE A The following work is excluded from the scope of work in this section and is included in other divisions of the specifications for inclusion in the scope of work of others WARRANTY Flashing at the roof Water supply and valves to flushing and fire sprinkler heads Installation of the plumbing access door provided under this section is to be by the forces erecting the shaft enclosure walls A Manufacturer s warranty: Furnish manufacturer s standard one () year warranty from date of temporary certificate of occupancy or similar, locally mandated permission to use the project common areas for their intended use Warranty shall apply to defects in product workmanship and materials WILKINSON HUTES ANADA Telephone: -- / Fax: --
3 Version 00 WILKINSON HUTES ANADA PAGE OF Part PRODUTS MANUFATURERS A Acceptable manufacturers: WILKINSON HUTES ANADA as distributed by Wilkinson chutes anada, Toronto, Ontario, ANADA Telephone: -- Substitutions: Not permitted omponents: The chute shall be inch (00 mm) diameter of US # gauge ( mm) aluminized steel as manufactured by Wilkinson hutes anada Intake Doors: Stainless steel, inches wide x 8 inches high (80 mm x 0 mm), bottom hinged, hand operated self-closing positive latching doors bearing ½ hour, c U L (Underwriters Laboratories Label) designation, and rated for a 0 F ( ) maximum door temperature rise over 0 minutes, with stainless steel trim in a c U L approved, Label, ½ hour assembly Discharge: Wilkinson hutes anada type A open end chute discharge door with F ( ) fusible link at the bottom of the chute discharge to close automatically when the ambient temperature reaches F ( ) as required by city or provincial building and/or fire codes Unit with c UL rating as described above Vent: hute shall extend full diameter through roof to metal top vent cap 0 inches (0 mm) above roof level with counter flashing and insect screen A roof curb [ ( mm) x ( mm) x minimum of 8 high (0 mm)] is required for flat roof conditions and is to be provided by others Specify stainless steel for aggressive environments Accessories: / inch (9 mm) IPS flushing spray head and / inch ( mm) sprinkler head above highest intake Additional / inch ( mm) sprinkler heads at every second intake (counting from the top) or as required by local code Provide Disinfecting & Sanitizing unit for installation in line to the flushing spray head onnection to flushing spray head, back flow prevention valve and electric control switch by others Provide inches (8 mm) wide x inches (8 mm) high right sidehinged, hand operated, self closing, positive latching, c UL /-hour labeled, stainless steel plumbing access door having stainless steel door trim for installation by forces erecting enclosing shaft wall Door for access to disinfecting & sanitizing unit above the highest intake door of the chute 8 Offsets (bends) in the chute, if required, shall be made the same diameter as the chute of # US gauge ( mm) aluminized steel and have an additional layer of # US gauge ( mm) aluminized steel reinforcing the impact area Offsets are not to deviate more than 0 o off the vertical axis of the chute 9 Provide rubberized sound coat vibration dampening compound to the exterior of the chute only Include sound isolator pads at each floor support frame WILKINSON HUTES ANADA Telephone: -- / Fax: --
4 Version 00 WILKINSON HUTES ANADA PAGE OF FARIATION 0 Sprinkler System: hute shall be protected internally by automatic sprinklers This requires a sprinkler at or above the top intake door of the chute, and in addition, a sprinkler shall be installed within the chute at alternate floor levels in building over two stories in height with mandatory sprinkler located at the lowest service level A The trash chute shall be fully factory assembled and all joints, except those required to separate the sections for shipment and installation shall be welded or lockseamed tight The floor intake doors shall be bolted in place on throats formed into the chute All chute sections shall flash inside the sections below and there shall be no bolts, clips, or other projections inside the chute to snag the flow of material Prepositioned support frames shall assure proper intake levels and there shall be an expansion joint in the chute between all support joints Discharge hoppers and offsets, where required, shall be reinforced and separately supported in the impact area Part EXEUTION EXAMINATION A Verification of conditions: Area in which system is to be located is correct size and location, and is prepared for installation of trash chute and components Installer s examination: Have installer of this section examine conditions under which construction activities of this section are to be performed, then submit written notification if conditions under which construction activities of this section are to be performed are unacceptable eginning construction activities of this section before unacceptable conditions have been corrected is prohibited General ontractor shall verify and record chute alignment with installer immediately following installation INSTALLATION A Install trash chute in accordance with shop drawings and manufacturer s printed installation instructions DEMONSTRATION A Arrange demonstration of system operation, conducted by manufacturer s representative, to Owner s maintenance personnel * END OF * WILKINSON HUTES ANADA Telephone: -- / Fax: --
5 NOTES: TYPIAL INTAKE PLAN 8mm ALL HUTES TO HAVE WELDED VERTIAL LOK SEAMS AND INSIDE LAP ROUNDAOUT JOINTS PARTITIONS AROUND HUTES NOT TO E PLAED UNTIL AFTER HUTE INSTALLATION, UTTING OF S OR HUTES SHALL E PERFORMED Y OTHERS MISELLANEOUS STEEL TO HAVE SHOP OAT OF PROTETIVE ENAMEL ONTRATORS TO VERIFY AND APPROVE ALL DIMENSIONS ON THESE DRAWING WITH ONDITIONS ON THE JO SITE WILKINSON HUTES ANADA WILL NOT E RESPONSILE FOR DEVIATIONS FROM THE DRAWING ONE APPROVED IF FRAMES ARE TO SIT ON SU S, PLEASE PROVIDE INFORMATION REGARDING THIKNESS OF FINISHED THE FINAL RESPONSIILITY FOR ENSURING THAT DOORS ARE SITTING FLUSH TO WALLS, MUST LIE ON TRADES ONSTRUTING THESE WALLS, DUE TO MOVEMENT WHIH MAY OUR AFTER INSTALLATION THIS DRAWING IS THE PROPERTY OF WILKINSON HUTES ANADA AND IS LOANED ON THE ONDITION THAT IT IS NOT TO E REPRODUED AND IS NOT TO E USED IN WHOLE OR PART TO FURNISH INFORMATION FOR THE MAKING OF DRAWING LINTEL, IF REQUIRED AOVE DOOR, Y OTHERS ROOF HUTE RISER TO E 00mm DIA FARIATE WITH ga ALUMINZED / SATIN OTE STEEL 00 Ø mm SLA OPENING REQUIRED A ROOF 000 VENT RISER HEIGHTS TO E DETERMINED HEIGHTS TO E DETERMINED TYPIAL INTAKE DOOR WILKINSON TYPE DOOR W 80mm WIDE x 0 mm HIGH OTTOM HINGED NOISELESS, SELF-LOSING, SELF-LATHING STAINLESS STEEL, TOP HINGED INSWINGING AFFLES EARING A ANADIAN UNDERWRITER'S LAORITORIES -/ HR, TEMPERATURE RISE 0F 0 MIN LAEL EMOSSED " RUISH" TRIM SET DISHARGE TYPE "A" HORIZONTAL AORDIAN, SPRING LOADED HELD OPEN ON A FUSILE LINK ASSEMLY ASSEMLY EARS -/ HOUR UL FIRE RATING FLUSHING SPRAY HEAD WITH ONNETION Y OTHERS 9mm ONNETOR READY FOR TYPIAL HUTE SUPPORT Y MEANS OF LIPS WELDED AT QUARTERS TO SIT ON ANGLE IRON AND AR GRID TYPE FRAME STEEL TO mm THIK MINIMUM F UL SPRINKLERS TO E INSTALLED AT TOP INTAKE AND ALTERNATE INTAKES ELOW AND READY FOR ONNETION Y OTHERS SPRINKLERS ARE ON: VENT TO EXTEND FULL DIAMETER THRU ROOF TO A HEIGHT OF 000 mm VENT TO E OVERED WITH A HINGED RAINAP WITH mm AIR SPAE AND HOLDOWN LIPS ROOF EXTENSION TO E ALUMINZED/SATIN OTE STEEL FINISH AND VENT SHALL E ALUMINZED/SATIN OTE STEEL DUT 9 8 A 0 HEIGHTS TO E DETERMINED DETAIL OF ROUNDAOUT JOINTS " " A " 89 HEIGHTS TO E DETERIMED 'A' EXPANSION st TRANSMITTAL RESUMITTAL APPROVED FOR FARITION JO NAME: '' EADED '' WELDED DISHARGE LOATION: REPRESENTATIVE: WILKINSON HUTES ANADA ITEM: ONE RUISH HUTE - WRA0 FILE # PO # JO #
SECTION BULLET- RESISTANT DOORS
1 SECTION 08 3950 BULLET- RESISTANT DOORS PART 1- GENERAL 1.01 SUMMARY A. This Section Includes: 1. Bullet- resistant steel door and frame systems. 2. Door hardware for bullet- resistant steel door and
More informationIF THIS SHEET IS NOT FILLED OUT, SIGNED AND RETURNED, PRODUCTION WILL BE POSTPONED UNTIL THIS DOCUMENT IS COMPLETED AND RETURNED.
X 2/18/2015 JDF Trash Chute & Trash Compactor P.O. Box 405 939 West Quincy St. Lakeland, FL 33802/33815 Phone: 800-659-1797 Fax: 863-683-9749 www.linenchutes.com Valiant Products, Inc. Trash/Linen Chutes
More informationC. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available.
SECTION 105113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION PANELBOARDS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 24 16 PANELBOARDS SPEC WRITER NOTE: Delete between // --- // if not applicable to project. Also, delete any other item or paragraph not applicable in the section
More information2. All work and materials shall be in full accordance with Local and State ordinance and with any prevailing rules and regulations.
General Conditions: 1. Deliver all food service equipment as specified herein, including that which is reasonably inferred, with all related items necessary to complete work shown on contract drawings
More informationSCI-FAB Product Specifications. Casework Section 1. Part 1 General
SCI-FAB Product Specifications Casework Section 1 Part 1 General 1.1 SCOPE OF WORK Includes all factory fabricated stainless steel casework as required by the project drawings. 1.2 TYPICAL INCLUSIONS A.
More informationDesign and Construction Standards SECTION ATHLETIC LOCKERS
SECTION 10505 ATHLETIC LOCKERS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. The provisions of the General Conditions, Supplementary Conditions, and the Sections included under Division 1, General Requirements,
More informationTABLE OF CONTENTS. 1.0 Scope. 2.0 References. 3.0 Definitions. 4.0 Submission and Design Requirements. 5.0 Materials 5.1 General 5.
1.0 Scope 2.0 References 3.0 Definitions 4.0 Submission and Design Requirements 5.0 Materials 5.1 General 5.2 Marking 6.0 Equipment 7.0 Production 7.1 Steel Octagonal Poles 7.2 Base Plate 7.3 Top Cap 7.4
More informationACORNWIRE.COM MESH PARTITIONS DIVISION 10 - SPECIALTIES WIRE MESH PARTITION FOLDING GATE
acorn WIRE ACORNWIRE.COM MESH PARTITIONS DIVISION 10 - SPECIALTIES 10 22 13 WIRE MESH PARTITION 10 22 16 FOLDING GATE GUIDE Page 4 / 5 No. 130A All wire type for normal industrial use. 7, 8, 9, 10 and
More informationMichigan State University Construction Standards SWITCHBOARDS, PANELBOARDS, AND CONTROL CENTERS PAGE
PAGE 262400-1 SECTION 262400 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationProduct Guide Specification
Product Guide Specification Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat,
More informationEast Central College
SECTION 013300 - SUBMITTAL PROCEDURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification
More informationA. Radius elbows with a construction radius of 1.5 the duct width are preferred to square elbows.
SECTION 233100 DUCTWORK 1.0 Acoustical duct lining in any part of the duct system is prohibited. All ductwork requiring insulation shall be externally insulated (Refer to the Sheet Metal Ductwork Insulation
More informationDETAILED STILE AND RAIL WOOD DOOR SPECIFICATION
DETAILED STILE AND RAIL WOOD DOOR SPECIFICATION UNIVERSITY CONTACT: Structural Services, Maintenance & Operations (302) 831-8456 PART 1 GENERAL DOORS 1.01 GENERAL PROVISIONS 1. The Drawings and General
More informationEMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL
EMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION 05720 METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL EMMEGI ARCHITECTURAL FENCING is a high quality steel fencing system comprised of a hybrid
More informationMusic Area Casework General 1.01 Summary Related Sections Definitions Qualifications and Quality Assurance
1.00 General 1.01 Summary Music Area Casework A. This section includes the following Scope of Work as referred to in the plans: 1. Thermally Fused Laminate manufactured casework, for use in music areas,
More informationSt. Monica Food Pantry
St. Monica Food Pantry 26 5113-1 ELECTRICAL WORK DIVISION 26 SECTION 265113 INTERIOR LIGHTING FIXTURES PART 1. GENERAL 1.1 WORK INCLUDES A. Extent, location, and details of interior lighting fixture work
More informationA. Action Submittals: Written and graphic information that requires Architect's responsive action.
SECTION 01330 - SUBMITTAL PROCEDURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 1 Specification
More informationSECTION HOLLOW METAL DOORS AND FRAMES
SECTION 081113 HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: Include construction details, material
More informationSECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS
SECTION 270536 - CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationB. Manufacturers: Square-D, G.E. or Westinghosue.
SECTION 16470 - PANELBOARDS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. General: Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSolid Surface Fabrications
USE THIS SECTION F WALL CLADDING AND MISCELLANEOUS FABRICATIONS OTHER THAN COUNTERTOPS. USE SECTION 06 61 18 F COUNTERTOPS. GENERAL NOTES TO SPECIFIER: THIS SPECIFICATION SECTION HAS BEEN PREPARED TO ASSIST
More information.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.
PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Installation
More informationB. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.
SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationSolid Surface Countertops
USE THIS SECTION FOR COUNTERTOPS. USE SECTION 06 61 16 FOR OTHER SOLID SURFACING APPLICATIONS INCLUDING WALL CLADDING AND MISCELLANEOUS FABRICATIONS. GENERAL NOTES TO SPECIFIER: THIS SPECIFICATION SECTION
More informationSECTION SHOP DRAWINGS, PRODUCT DATA, AND SAMPLES
SECTION 01334 SHOP DRAWINGS, PRODUCT DATA, AND SAMPLES PART 1 GENERAL 1.01 SUMMARY A. Submit to the ENGINEER for review, such working drawings, shop drawings, test reports and data on materials and equipment
More informationTaylor County July 2011 SECTION SHOP DRAWINGS, WORKING DRAWINGS AND SAMPLES
SECTION 01340 SHOP DRAWINGS, WORKING DRAWINGS AND SAMPLES PART 1 - GENERAL 1.1 REQUIREMENTS INCLUDED A. Contractor shall submit to the Architect/Engineer for review and exception, if any, such working
More informationSECTION PVC THATCH SHINGLE ROOFING SYSTEM PART 1 GENERAL 1.01 SUMMARY
SECTION 07312 PVC THATCH SHINGLE ROOFING SYSTEM PART 1 GENERAL 1.01 SUMMARY A. This Section Includes the following: 1. Endureed Dominica PVC thatch shingles. 2. Self- adhering sheet underlayment. B. Related
More informationSECTION SIGNAGE
SECTION 10 14 00 SIGNAGE PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division-1 specification section, apply
More informationCOMMERCIAL KITCHEN HOOD WORKSHEET/ CHECKLIST
COMMERCIAL KITCHEN HOOD WORKSHEET/ CHECKLIST Two copies of this worksheet/checklist must accompany plans sets submitted with commercial kitchen application. The applicant is responsible for assuring the
More informationENDUREED VIVA SERIES Specifications
ENDUREED VIVA SERIES Specifications SECTION 07312 HDPE THATCH SHINGLE ROOFING SYSTEM PART 1 GENERAL 1.01 SUMMARY A. This Section Includes the following: 1. Endureed Viva Series synthetic thatch shingles.
More informationJEFFERSON LAB TECHNICAL ENGINEERING & DEVELOPMENT FACILITY (TEDF ONE) Newport News, Virginia
BULLETIN NO. 6 TO THE PLANS AND SPECIFICATIONS FOR JEFFERSON LAB TECHNICAL ENGINEERING & DEVELOPMENT FACILITY (TEDF ONE) Newport News, Virginia EwingCole Architects.Engineers.Interior Designers.Planners
More informationB. Bidders shall acknowledge receipt of this Addendum in writing on his Proposal Form.
McKee and Associates Architecture and Interior Design Addendum No. THREE Date: 12.11.17 Project: A NEW BUILDING FOR THE GREATER LIMESTONE COUNTY CHAMBER OF COMMERCE ATHENS, ALABAMA A3.1 GENERAL PROJECT
More informationA. Action Submittals: Written and graphic information that requires Engineer's responsive action.
SECTION 01330 - SUBMITTAL PROCEDURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 1 Specification
More information1. Field measurements must be taken to verify existing conditions prior to installation.
General Conditions: 1. Field measurements must be taken to verify existing conditions prior to installation. 2. Deliver and set in place all food service equipment as specified herein, including that which
More informationThe School District of Palm Beach County Project Name SDPBC Project No. SECTION ( ) SIGNAGE PART 1 GENERAL 1.1 RELATED DOCUMENTS
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 10441 (10 14 00) SIGNAGE A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division-1 specification section,
More informationDIVISION 11 EQUIPMENT SECTION PHOTO DARKROOM FUME EXHAUST VENT-HOODS
DIVISION 11 EQUIPMENT SECTION PHOTO DARKROOM FUME EXHAUST VENT-HOODS PART 1 GENERAL 1.01 Scope of Work A. Provide material, accessories, tools, equipment and labor as required for the complete fabrication
More informationA. Extent of structural precast concrete work is shown on drawings and in schedules.
SECTION 03 41 00 - STRUCTURAL PRECAST CONCRETE PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification
More informationSECTION 10520: FIRE EXTINGUISHERS AND CABINETS
SECTION 10520: FIRE EXTINGUISHERS AND CABINETS PART 1 GENERAL 1.01 GENERAL REQUIREMENTS: A. This section specifies fire extinguishers, cabinets for fire extinguishers, fire and other accessories. Their
More informationTable of Contents F Series Frames
Table of Contents F Series Frames How to Order Frames... F 1 F Series Spec Sheet... F 2 F Series Profiles 1 of 6... F 3 F Series Profiles 2 of 6... F 4 F Series Profiles 3 of 6... F 5 F Series Profiles
More informationB. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.
SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section includes standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationChevy Chase Club June 30, 2008 Bowie Gridley Architects
SECTION 081433 - STILE AND RAIL WOOD DOORS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION SUBMITTAL PROCEDURES
SECTION 01330 - SUBMITTAL PROCEDURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 1 Specification
More informationSECTION CONCRETE REINFORCEMENT FOR STEAM UTILITY DISTRIBUTION
PAGE 032015-1 SECTION 032015 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification sections,
More informationPROJECT LOCATION SECTION PREFINISHED STEEL DOOR FRAMES
SECTION 08 1213.17 PART 1 - GENERAL 1.01 SECTION INCLUDES A. Prefinished steel door frames. B. [Sidelites] [, borrowed lites] [, and transom] assemblies. 1.02 RELATED REQUIREMENTS A. Section 06 2000 Finish
More information1. Land survey Work. 2. Civil and Structural engineering services.
SECTION 01050 FIELD ENGINEERING PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division-1 Specification
More informationUNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-08 33 13 (May 2009) Change 2-11/12 --------------------------- Preparing Activity: USACE Nontechnical Title Revision (August 2015) UNIFIED FACILITIES GUIDE SPECIFICATIONS
More informationB. Terracotta Precast Facade Assembly consisting of single-leaf, through body color terracotta clay tiles.
SECTION 07 4229 TERRACOTTA CLAY TILE IN PRECAST SPECIFICTION FOR TERRART SOLID PART 1 GENERAL 1.1 SECTION INCLUDES A. Drawings and general provisions of the Contract, including General and Supplementary
More informationSymphony II Adaptable Table System
Symphony II Adaptable Table System 1.00 General 1.01 Conditions 1.02 Scope of work 1. This section covers all materials, equipment, tools and labor for the supply and installation of the laboratory Symphony
More informationMISSISSIPPI STATE UNIVERSITY Office of Planning Design and Construction Administration
SECTION 01 340 - SHOP DRAWINGS, PRODUCT DATA AND SAMPLES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other
More informationTYPE "B" GAS VENT. Do not connect gas vent to a solid or liquid fuelled appliance or any appliance requiring a chimney.
TYPE "B" GAS VENT SD (sizes 3", 4", 5", 6", 7") INSTALLATION INSTRUCTIONS Type "B" Gas Vents are strictly for interior or enclosed exterior use or exterior use above a roof line. Read vent and appliance
More informationSECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP
1 1 1 0 1 0 1 0 1 SECTION 1 1 CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP BASED ON DFD MASTER SPECIFICATION DATED /01/ P A R T 1 - G E N E R A L SCOPE The work under this section shall consist of
More informationCopyright 2017 AIA MasterSpec Premium 05/17 PRODUCT MASTERSPEC LICENSED BY ARCOM TO WEREVER PRODUCTS, INC.
This Product MasterSpec Section is licensed by ARCOM to Werever Products, Inc. ("Licensee"). This proprietary Product MasterSpec Section uses modified original MasterSpec text. Revisions made to the original
More informationSlate Shingle Specifications
Slate Shingle Specifications California Slate is a proud member of the Slate Roofing Contractors Association of North America, Inc. (SRCA) which publishes Section 07310 Slate Shingles setting forth architectural
More information2016 Specification Treads, Base, Stringers and other Amenities Wausau Tile Precast Epoxy Terrazzo
2016 Specification Treads, Base, Stringers and other Amenities 09400 Wausau Tile Precast Epoxy Terrazzo PART 1 - GENERAL 1.1 SUMMARY A. Perform all work required to complete, as indicated by the Contract
More informationREVISION #1. Section. fire alarm B. C. the hot. intent of. required. manufacturer. materials. C. Warranty
HOT AISLE CONTAINMENT SYSTEM (HACS) REVISION #1 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. B. C. Drawings and general provisions of the Contract, including General and Supplementary. Conditions apply to
More information1.1 RELATED DOCUMENTS
SECTION 050505 -BEVEL RAIL ENDS PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the contract, including General and Supplementary Conditions and Division 01 Specification Sections
More informationTufftec Lockers Specifications & Drawings SPECIFICATIONS & DRAWINGS
Tufftec Lockers Specifications & Drawings SPECIFICATIONS & DRAWINGS Tufftec Lockers Specifications Tufftec Lockers Specifications & Drawings TUFFTEC LOCKERS Solid Plastic Lockers Specifications - Section
More information1. ASME A Scheme for the Identification of Piping Systems.
SECTION 40 05 53 - IDENTIFICATION FOR PROCESS PIPING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Nameplates. 2. Tags. 3. Stencils. 4. Pipe markers. 5. Labels. 6. Lockout devices. B. Related Requirements:
More informationTOLERANCES AND CLEARANCES FOR COMMERCIAL HOLLOW METAL DOORS AND FRAMES
HOLLOW METAL MANUAL AMERICAN NATIONAL STANDARDS ANSI/ NAAMM HMMA-841 13 ANSI/NAAMM HMMA 841-13 METAL DOORS & FRAMES November 21, 2013 8d TOLERANCES AND CLEARANCES FOR COMMERCIAL HOLLOW METAL DOORS AND
More informationGUIDELINE SPECIFICATIONS
GUIDELINE SPECIFICATIONS GORDON MILLENNIUM DECORATIVE METAL COLUMN COVERS DIVISION 05 7500 or DIVISION 09 2000 Note To Specifier: Column Covers are a finished, decorative product and should be installed
More informationProduct Guide Specification
Extrutech Plastics, Inc. September 2012 5902 West Custer Street Manitowoc, Wisconsin 54220 Toll Free 888-818-0118 Phone 920-684-9650 Fax 920-684-4344 Website www.epiplastics.com E-mail info@epiplastics.com
More informationD. Product Certificates: Signed by manufacturers of casework certifying that products furnished comply with requirements.
SECTION 12356 - CASEWORK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationC. HMMA 863: Guide Specifications for Detention Security Hollow Metal Doors and Frames
SECTION 083463 DETENTION DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION FINISH HARDWARE
SECTION 08710 PART I - GENERAL 1.01 DESCRIPTION A. Scope: Work under this Section shall include all materials and installation necessary to provide Finish Hardware as shown and detailed on the Drawings
More informationINDEX OF SPECIFICATIONS SECTION F SPECIAL CONDITIONS DIVISION 1 - GENERAL REQUIREMENTS:
INDEX OF SPECIFICATIONS SECTION F SPECIAL CONDITIONS DIVISION 1 - GENERAL REQUIREMENTS: 013300 SUBMITTAL PROCEDURES 018116 CONSTRUCTION WASTE MANAGEMENT DIVISION 2 EXISTING CONDITIONS: 023000 EARTHWORK
More informationSeries 9000 Vinyl Single Hung
Series 9000 Single Hung Series 9000 Vinyl Single Hung Contents List of Architectural Drawings...9000SH - 3 Elevations - Single Hung...9000SH - 4 Available Sizes - Single Hung...9000SH - 5 Elevations -
More informationB. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.
SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationSeries 9000 Vinyl Fixed Window
Series 2030 Picture Window Series 9000 Vinyl Fixed Window Contents List of Architectural Drawings... 9000PW - 3 Elevations - 9000 Fixed... 9000PW - 4 Available Sizes - 9000 Fixed... 9000PW - 5 Elevations,
More informationSECTION SUBMITTAL PROCEDURES
SECTION 01330 SUBMITTAL PROCEDURES PART 1 - GENERAL 1.1 DESCRIPTION A. Scope: 1. CONTRACTOR shall provide submittals in accordance with the General Conditions as modified by the Supplementary Conditions,
More informationA. Section includes administrative provisions for coordinating construction operations on Project including, but not limited to, the following:
SECTION 01 31 00 PROJECT MANAGEMENT AND COORDINATION PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division
More informationSECTION METAL FABRICATIONS
SECTION 05100 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for metal fabrications, including minimum requirements for fabricator, and galvanizing. 1.02 REFERENCE STANDARDS A. ASTM
More informationBovard Studios Inc. Section April 6, 2004 Page 1
April 6, 2004 Page 1 This section includes solid flush and surface articulated wood doors, may have veneer facing, solid or glazed (stained glass) design, factory pre-fit, may be factory finished or site
More informationProduct Guide Specification
Halfen USA, Inc. July 2014 8521 FM 1976 PO Box 547 Converse, Texas 78109 Toll Free 800-423-9140 Fax 877-683-4910 Website www.halfenusa.com Email info@halfenusa.com Product Guide Specification Specifier
More informationSECTION FRAMELESS GLASS SLIDING BI-FOLD SHOWER DOOR HARDWARE
1 SECTION 10 2880 FRAMELESS GLASS SLIDING BI-FOLD SHOWER DOOR HARDWARE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationAMBICO Limited Section and WOOD BULLET RESISTANT DOORS AND FRAMES Page 1
Page 1 This section includes AMBICO Bullet Resistant, Wood Doors and Bullet Resistant Steel Frames which meet the UL752 Standard for Bullet-Resisting Equipment. This section relies on both the Canadian
More informationUNION COUNTY VOCATIONAL-TECHNICAL SCHOOLS West Hall Addition Project Raritan Road, Scotch Plains, NJ
SECTION 013300 - SUBMITTAL PROCEDURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 1 General
More informationProduct Guide Specification
Shield Casework February 2014 3421 Merriam Lane Overland Park, Kansas 66203 Phone 913-744-2183 Fax 913-384-3477 Website www.shieldcasework.com E-mail info@shieldcasework.com Product Guide Specification
More informationInstallation Instructions. 45 and 60-Minute Fire-Rated Neutral Pressure Veneered Door Frame UBC & UL-10C
Installation Instructions 45 and 60-Minute Fire-Rated Neutral Pressure Veneered Door Frame UBC 7-2-1997 & UL-10C Door Requirements: Consult the door manufacturer to make sure that the doors are qualified
More informationSeries 6000 Vinyl Single Hung
Series 6000 Horizontal Slider Series 6000 Vinyl Single Hung Contents List of Architectural Drawings...6000SH - 3 Elevations - Single Hung...6000SH - 4 Available Sizes - Single Hung...6000SH - 5 Series
More informationINTEX Millwork Solutions SECTION EXTERIOR PVC PERGOLAS (IBC Compliant)
SECTION 066030 EXTERIOR PVC PERGOLAS (IBC Compliant) PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and other Contract Documents, listed in the agreement between the Owner and Contractor, apply to
More informationSECTION SITE FURNISHINGS FOR CFCRT. 1. American Society for Testing and Materials (ASTM).
PART 1 - GENERAL 1.1 SECTION INCLUDES A. Benches. B. Trash receptacles. C. Bike storage. 1.2 REFERENCE STANDARDS A. Including but not limited to: 1. American Society for Testing and Materials (ASTM). 1.3
More informationUCCS University Hall Fire Sprinkler System Upgrade March 1, 2011 RTA SECTION SUBMITTAL PROCEDURES PART 1 - GENERAL
SECTION 013300 - SUBMITTAL PROCEDURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification
More informationWAL-MART SUPERCENTER # ; Milwaukie, OR: SPECIFICATIONS. Revisions to Specification Fence
MILWAUKIE OR #3144-00 ADDENDUM #5 NARRATIVE: 11-08-12 WAL-MART SUPERCENTER #3144-00; Milwaukie, OR: SPECIFICATIONS SPECIFICATIONS Revisions to Specification 02822 Fence Spec division 02822 has been revised
More informationDENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION METAL LOCKERS
PART 0 A/E INSTRUCTIONS 0.01 GENERAL DESIGN REQUIREMENTS A. Architect shall coordinate with the DPS Project Manager the type, layout and size of lockers required on the project. B. Varsity athletic Lockers
More informationSECTION SUBMITTAL PROCEDURES
SECTION 013300 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply
More informationTremLock T-138 INSTALLATION MANUAL T-138 www.tremcoroofing.com 3735 Green Road Beachwood, Ohio 44122 1.800.852.6013 50 Beth Nealson Drive Toronto, Ontario M4H 1M6 1.800.668.9879 7241 6/8/18 TABLE OF CONTENTS
More informationDIVISION 11 EQUIPMENT SECTION PHOTO DARKROOM CASEWORK
DIVISION 11 EQUIPMENT SECTION PHOTO DARKROOM CASEWORK PART 1 GENERAL 1.01 Scope of Work A. Provide material, accessories, tools, equipment and labor as required for the complete fabrication and installation
More informationUNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-26 53 00.00 40 (November 2015) ----------------------------------- Preparing Activity: NASA Superseding UFGS-26 53 00.00 40 (November 2008) UFGS-26 53 00 (August 2008)
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 01 3300 - SUBMITTAL PROCEDURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification
More informationSECTION SUBMITTAL PROCEDURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 01 33 00 - SUBMITTAL PROCEDURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification
More informationMETAL FABRICATION SECTION 8: METAL FABRICATION SCOPE MATERIAL.
METAL FABRICATION SCOPE This specification applies to all metal intended to be rubber lined. Metals furnished must conform to this specification with respect to suitability for rubber lining or covering.
More informationSECTION IDENTIFYING DEVICES
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 10441 IDENTIFYING DEVICES A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division-1 specification section,
More informationSingle-Family Dwelling Submittal Requirements
Single-Family Dwelling Submittal Requirements The purpose of this guideline is to assist our customers in preparing for plan submittal. The items listed must be included before your plans can be accepted
More informationStormTrap Guide Specification. StormTrap SingleTrap on Pad Foundation Groundwater BELOW Invert Revised 11/21/18
StormTrap Guide Specification StormTrap SingleTrap on Pad Foundation Groundwater BELOW Invert Revised 11/21/18 This product guide specification is written according to the Construction Specifications Institute
More informationSECTION ARCHITECTURAL WOOD CASEWORK
SECTION 06410 - ARCHITECTURAL WOOD CASEWORK PART 1 GENERAL 1.01 SECTION INCLUDES A. Wood cabinets for opaque finish. B. Flush wood paneling for transparent finish. C. Factory finishing. 1.02 RELATED REQUIREMENTS
More informationSECTION CABLE TRAYS
SECTION 16139 CABLE TRAYS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationStorage and Installation of welded LL Hollow Metal Door Frames in Steel Studs
Storage and Installation of welded LL Hollow Metal Door Frames in Steel Studs Introduction This guide specification is intended to stress the necessary precautions and requirements for receipt, storage,
More informationSECTION Display Case Door Series 1301-CM
1 SECTION 12 3559 Display Case Door Series 1301-CM PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Display Case Glass Doors. 2. Sidelites. B. Related work in other sections: 1. 08 8000- Glazing
More informationSeries 9000 Vinyl Fixed Window
Series 2030 Picture Window Series 9000 Vinyl Fixed Window Contents List of Architectural Drawings... 9000PW - 3 Elevations - 9000 Fixed... 9000PW - 4 Available Sizes - 9000 Fixed... 9000PW - 5 Elevations,
More information