LED Infinity Mirror Controller, 32 LEDs, Multiple Patterns.
|
|
- Stephany Hicks
- 5 years ago
- Views:
Transcription
1 Food Living Outside Play Technology Workshop LED Infinity Mirror Controller, 32 LEDs, Multiple Patterns by ChromationSystems on May 10, 2010 Table of Contents LED Infinity Mirror Controller, 32 LEDs, Multiple Patterns 1 Intro: LED Infinity Mirror Controller, 32 LEDs, Multiple Patterns 2 File Downloads 2 Step 1: Parts 3 Step 2: Resistors, Capacitor & Sockets 4 Step 3: Jumper and Terminal Block 5 Step 4: Push Button 6 Step 5: Power & LED+ 7 Step 6: Plug in the ICs & Finish 8 Step 7: Optional: Add ICSP 9
2 Author:ChromationSystems wwwchromationsystemscom Designing electronic creations from microcontrollers, LEDs and anything else I can pull out of a dumpster and make use of Intro: LED Infinity Mirror Controller, 32 LEDs, Multiple Patterns As simple a circuit as can be A 12F675 controls a high-power shift register, which in turn controls up to 48 LEDs at 20ma per, (~120mA per channel) in 8 channels(groups), Software controlled patterns create seamless effects from group to group With 4-state greyscale ( 4 states of LED of brightness ) a vast amount of patterns/effects are possible It was designed to go along with my 8"x8" 32 LED Infinity Mirrors Instructable will be Posted Soon A Gallery of all my Infinity Mirrors A single momentary-pushbutton cycles through the programmed patterns Comes loaded with 5 patterns, and the ability to add more through re-writing the firmware Kits, Including 32 LEDs, colors buyer's choice, can be bought from my store at wwwchromationsystemscom The Eagle Schematics, PCB layout, and Source Code in Assembly can be purchased all together in a Developer Package Or just download the Source Code The Schematic, HEX File, and Datasheet are in the ZIP below DISCLAIMER: Recreate this project at your own risk 1 Resistors, value will vary with LED color choice 2 Button and perf-board 3 10k resistor and 01uf Capacitor 4 Optional Barrel Jack and Plug 5 Super teeny tiny screw down terminal 6 22ga, dual strand wire 7 Chips and sockets File Downloads
3 ChromationSystems-8ChanLEDControllerFileszip (361 KB) [NOTE: When saving, if you see tmp as the file ext, rename it to 'ChromationSystems-8ChanLEDControllerFileszip'] Step 1: Parts To Purchase a Full Kit with all the parts, including 32 5mm LEDs Visit my Store Also Available with no LEDs Here Layout all the Parts: - programmed 12F675 Buy One - 8 pin socket - PCB Buy One - 8 Position Screw-Down Terminal, with 01" (DIP) spacing - TPIC6C596, high power shift register - 01uf Capacitor - 16 pin socket - 10k 1/4w resistor (Brown, Black, Orange) - 8 resistors, value depends on LED Color Approx: ohm - 32 LEDs, choice of colors - board mount momentary push-button ( kit comes with an extra panel-mount button ) - scrap of perfboard - Dual-Strand wire, 22 ga - ~2" of solid strand for jumping - 5 volt, 600ma+ PSU Optional: with barrel Jack Buy One Optional: ( supplied with the Kit ) - panel mount DC jack - PSU with correct DC Plug Tools: - Soldering Iron 1 Resistors, value will vary with LED color choice 2 Button and perf-board 3 10k resistor and 01uf Capacitor 4 Optional Barrel Jack and Plug 5 Super teeny tiny screw down terminal 6 22ga, dual strand wire 7 Chips and sockets
4 Step 2: Resistors, Capacitor & Sockets Place the resistors first - R1 is a 10kohm (Brown, Black, Orange), 1/4w, it is the pull-up for the push-button switch - R2 - R9 are the resistors for the LEDs - The values of R2-R9 vary depending on the Color of the LEDs and the amount per channel - Depending the resistors may or may not sit flat on the PCB, if they are to big, just place them in like in the images below Flip every other one so the leads are next to each other Place the Capacitor C1 next - It is not polarized and can be placed in either way Sockets are last, be careful placing them Make sure all the leads get into their correct hole There is a notch in the sockets that should line up with the image on the top-side illustration Solder them in securely and watch for solder bridges between pins 1 Some Resistors won't sit flat, so they can stand up
5 Step 3: Jumper and Terminal Block J1 & J2: - Take about a 2" peice of solid strand wire and run it from J1 to J2(see image) - Trim it to size and solder Terminal Block: It is quite tiny, you need a eyeglass screwdriver to tighten it - Place it with the opening facing outward and it sitting flush with the PCB 1 I fixed this 2 J1 3 J2
6 Step 4: Push Button The push-button is used to cycle through the available patterns Supplied with the kit is a board mount button, a piece of perforated board, and a panel-mount pushbutton, I prefer the board-mount button, but the panel-mount is easier (but uglier) For the board-mount button and perf-board: - Place the the switch in the most center area of the perf-board - Fold the leads over and clip leaving about an 1/8th" lead to hold the button in place - Figure out how long you will need the button wire and cut a section off of the supplied dual-strand wire About 4"-6" - Solder a one strand of the dual strand wire to each lead - Solder in the other end of the dual strand wire into the board holes marked "BUTTON"
7 Step 5: Power & LED+ The power jack is labeled "PWR" on the board - Estimate how much wire you will need for your power leads and cut a piece to length About 4" - Solder in the ends of the wire into the board, I would suggest using white for V+ and blue for V- - If you are using the optional barrel jack, see images for soldering instructions There are 3 contacts only 2 are used mistaking which wire goes where could cause damage to the controller, please see images LED+ is hooked to V+ input through the PCB and goes to the LED's Anodes *If you are building the Infinity Mirror Kit (LINK) Skip this, as it is easier to solder the LED+ wires into the Infinity Mirror while the outer walls are off You'll just solder the PCB directly to the LEDs - Taking another length of dual-strand wire, cut it to length( about 4") - And solder it into the PCB 1 LED+ 2 Voltage Input 3 Button 1 Center Tap, Positive 2 Ground
8 1 V+ 2 V- Step 6: Plug in the ICs & Finish - Looking at either IC, there is a notch on one end, that should line up with the notch in the sockets - Carefully place into the socket, the leads may need to be bent inwards gently with your fingers for them to fit Flip it over and very carefully look over your soldering and look for solder bridges or dullness on the solder And fix anything you find There isn't any easy way to test this controller, so just follow the instructions and it will work when it is placed into an Infinity Mirror Optional: - If it really needs to be tested, get 8 LEDs and ohm resistors and twist or solder a resistor to each of the LEDs cathode(gnd or flat side) - The other side of the resistors gets screwed into the terminal block And all the LED anodes are hooked together and then hooked to +5 volts - Power to the controller should get hooked up - When powered, the LEDs should start lighting and going through patterns - Test the push button switch and ensure that is its changing the pattern Thanks for Reading Subscribe or watch for my future projects Including: - 8"x8" Infinity Mirrors, 32 LEDs with this Controller - 9 Watt LED Full Color Can Light with DMX-512 Control 1 I fixed this later 2 the dot shows where Pin 1 is 3 Pin 1 4 PWR 5 LED+ 6 Button
9 Step 7: Optional: Add ICSP If you want to easily reprogram the Microcontroller an ICSP header can be easily added Wire and a header can be purchased separately I use a PICKit2 Clone(chinese) and It works great The MCLR is on the end so I use a different colored wire on that pin - Start by securing the 5-pin header to a helping-hand or equivalent - Tin all 5 of the pins - Strip an 1/8" of wire off an tin it with some solder - Solder the wires onto the header, save the odd wire for one of the end pins, as this is used for orientation when connecting it to a programmer Remove the ICs from their sockets before continuing - Depending on the pinout of your programmer Take a wire that is soldered onto the header and from the bottom(copper side) find where it should go and solder Make sure it can not touch any of the surrounding pins - Finish soldering all the wires to their pins - Check over all your solder joints and ensure no wires are shorting - Plug it into your programmer and test for connection to PIC - The push-button will function oddly while a programmer is attached, it is hooked up to MCLR as an input So detach the programmer from the ICSP while testing the button
10
4ms SCM Breakout. Kit Builder's Guide for PCB v2.1 4mspedals.com
4ms SCM Breakout Kit Builder's Guide for PCB v2.1 4mspedals.com Shuffling Clock Multiplier Breakout This guide is for building a Shuffling Clock Multiplier Breakout module (SCMBO) version 2.1 from the
More informationMono Amplifier. LM386 Headphone Amp
Mono Amplifier LM386 Headphone Amp Layout On/Off Switch - cuts power to the circuit Mono Input Jack: use either L or R or solder together Schematic Step 1 - Parts List 1.) R1-10ohm Resistor - Brown Black
More informationABC V1.0 ASSEMBLY IMPORTANT!
ABC V1.0 ASSEMBLY Before starting this kit, prepare the following tools: Soldering iron (15-20W will do), flush cutters, no.2 hex screwdriver or allen key and phillips screwdriver. Also briefly go through
More information16 Bit Micro Experimenter Assembly and Check out Instructions
16 Bit Micro Experimenter Assembly and Check out Instructions The kit you purchased that includes PCB, schematic, complete parts list and these assembly instructions. A top picture of the complete assembly
More informationBill of Materials: Metronome Kit PART NO
Metronome Kit PART NO. 2168325 The metronome kit allows you to build your own working electronic metronome. Features include a small speaker, flashing LED, and the ability to switch between several different
More informationAssembly Instructions
Assembly Instructions For the SSQ-2F 3.1 MHz Rife Controller Board Kit v1.41 Manual v1.00 2012 by Ralph Hartwell Spectrotek Services GENERAL ASSEMBLY INSTRUCTIONS Arrange for a clean work surface with
More informationBill of Materials: PWM Stepper Motor Driver PART NO
PWM Stepper Motor Driver PART NO. 2183816 Control a stepper motor using this circuit and a servo PWM signal from an R/C controller, arduino, or microcontroller. Onboard circuitry limits winding current,
More informationLDB-1 Kit Instructions Page 1 of 8
LDB-1 Kit Instructions Page 1 of 8 Important Information Congratulations and thank you for your purchase of the LDB-1 Little Drummer Boy Analog Drum Machine Kit! Before you start, please read the enclosed
More informationDigital Electronics & Chip Design
Digital Electronics & Chip Design Lab Manual I: The Utility Board 1999 David Harris The objective of this lab is to assemble your utility board. This board, containing LED displays, switches, and a clock,
More informationPingable Envelope Generator
Pingable Envelope Generator Kit Builder's Guide for PCB v1.0.3 4mspedals.com PEG This guide is for building a Pingable Envelope Generator (PEG), which is an intermediate-level kit. You should be confident
More informationCongratulations on your purchase of the SparkFun Arduino ProtoShield Kit!
Congratulations on your purchase of the SparkFun Arduino ProtoShield Kit! Well, now what? The focus of this guide is to aid you in turning that box of parts in front of you into a fully functional prototyping
More informationD.I.Y L.E.D CUBE 4X4X4. Level: Intermediate
EN D.I.Y L.E.D CUBE 4X4X4 Level: Intermediate AK-125 TABLE OF CONTENTS Parts List... 2 Soldering Guide (Part A)... 3 Soldering Guide (Part B)... 5 Soldering Guide Without Recommend Products... 8 Appendix...
More informationCircuit Board Assembly Instructions for Babuinobot 1.0
Circuit Board Assembly Instructions for Babuinobot 1.0 Brett Nelson January 2010 1 Features Sensor4 input Sensor3 input Sensor2 input 5v power bus Sensor1 input Do not exceed 5v Ground power bus Programming
More informationSoftRock v6.0 Builder s Notes. May 22, 2006
SoftRock v6.0 Builder s Notes May 22, 2006 Be sure to use a grounded tip soldering iron in building the v6.0 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),
More informationHeartboard PCB Assembly Instructions
Heartboard PCB Assembly Instructions Thanks for purchasing a Heartboard! These instructions will guide you through assembling and testing the Heartboard. Let s get started! Stuff you need Soldering iron
More informationLITTLE NERD v1.1 Assembly Guide
last update: 9. 3. 2016 LITTLE NERD v1.1 Assembly Guide bastl instruments.com INTRODUCTION This guide is for building Little Nerd module from Bastl Instruments. It is good to have basic soldering skills
More informationConstruction Guide European Version
Construction Guide European Version PCB This section describes how to build up the DRO-350 printed circuit board (PCB). The bare PCB is available for purchase on the order page. Static Protection Bare
More informationHow to build a Cracklebox. Red Wierenga Brooklyn College Center for Computer Music October 13, 2015
How to build a Cracklebox Red Wierenga Brooklyn College Center for Computer Music October 13, 2015 What s a Cracklebox? What s a Cracklebox? The Cracklebox was developed by Michel Waisvisz and others at
More informationIntroduction 1. Download socket (the cable plugs in here so that the GENIE microcontroller can talk to the computer)
Introduction 1 Welcome to the magical world of GENIE! The project board is ideal when you want to add intelligence to other design or electronics projects. Simply wire up your inputs and outputs and away
More informationTelecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering tips: Removing Current Wiring: Step 1. Step 2.
Telecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers Wire Strippers 3/8 Drill Bit 5/32 Drill Bit
More informationWelcome! Welcome to the LVL1 TV-B-Gone workshop. We will be covering the following: How the TV-B-Gone works Basic soldering technique Component identi
TV-B-Gone LVL1 Welcome! Welcome to the LVL1 TV-B-Gone workshop. We will be covering the following: How the TV-B-Gone works Basic soldering technique Component identification Construction of a Super TV-B-Gone
More information555 Morse Code Practice Oscillator Kit (draft 1.1)
This kit was designed to be assembled in about 30 minutes and accomplish the following learning goals: 1. Learn to associate schematic symbols with actual electronic components; 2. Provide a little experience
More informationLine-Following Robot
1 Line-Following Robot Printed Circuit Board Assembly Jeffrey La Favre October 5, 2014 After you have learned to solder, you are ready to start the assembly of your robot. The assembly will be divided
More informationInstallation tutorial for Console Customs Xbox Mode Dual Button (RFX-5B) Rapid fire Microchip for all Wired and Wireless controllers
Installation tutorial for Console Customs Xbox 360 5-Mode Dual Button (RFX-5B) Rapid fire Microchip for all Wired and Wireless controllers This tutorial is designed to aid you in installation of a console
More informationSoftRock v5.0 Builder s Notes. December 12, Building a QSD Kit
SoftRock v5.0 Builder s Notes December 12, 2005 Building a QSD Kit Be sure to use a grounded tip soldering iron in building the QSD board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),
More informationProgrammable Timer Teaching Notes Issue 1.2
Teaching Notes Issue 1.2 Product information: www.kitronik.co.uk/quicklinks/2121/ TEACHER Programmable Timer Index of sheets Introduction Schemes of work Answers The Design Process The Design Brief Investigation
More informationSDR Cube Transceiver Online Assembly Guide
SDR Cube Transceiver Online Assembly Guide Detailed construction notes for building and testing each of the SDR Cube kit modules Home Bill of Materials I/O Board Controls Board DSP Board Softrock SR-Base
More informationMICROGRANNY v2.1 - Assembly Guide
last update: 9. 5. 2017 MICROGRANNY v2.1 - Assembly Guide bastl-instruments.com INTRODUCTION Welcome to the assembly guide for the MicroGranny kit. MicroGranny is a monophonic granular sampler by Bastl
More informationAssembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
More informationLesson 2: Soldering. Goals
Introduction: Its time to learn how to solder. So you have met all the components needed to make a DIY Gamer, now it s time to put it together. Soldering is joining the components to the printed circuit
More informationtinycylon Assembly Instructions Contents Written by Dale Wheat Version August 2016 Visit dalewheat.com for the latest update!
tinycylon Assembly Instructions Written by Dale Wheat Version 2.1 10 August 2016 Visit dalewheat.com for the latest update! Contents Assembly Instructions...1 Contents...1 Introduction...2 Quick Start
More informationSoftRock v6.0 Builder s Notes. April 6, 2006
SoftRock v6.0 Builder s Notes April 6, 006 Be sure to use a grounded tip soldering iron in building the v6.0 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0. inch diameter),
More informationSimon Tilts Assembly Guide
Page 1 of 20 Simon Tilts Assembly Guide Introduction Simon Tilts is a memory game very similar to Simon Says, but instead of pressing buttons, the player is challenged to rotate the device in a specific
More informationIR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015
IR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015 1 2 For the main circuits of the line following robot you soldered electronic components on a printed circuit board (PCB). The
More informationExplorer Wiring Kit (assembled)
Explorer Wiring Kit (assembled) For Vintage, Firestorm & Standard Series Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers
More informationPacific Antenna Field Strength Indicator Kit
Pacific Antenna Field Strength Indicator Kit Description The Field Strength Indicator kit from Pacific Antenna provides a visual way to monitor the presence and relative strength RF fields through the
More informationGeiger Counter Kit Assembly Instructions ( )
Geiger Counter Kit Assembly Instructions (2012-05-11) To build this kit, you should know how to solder. And it will be much easier if you have made other kits before. But even if this is your first kit,
More informationTen Tec DDS Board Assembly Procedure
05 May 2014 Ten Tec DDS Board Assembly Procedure You will find a photo of a completed board at the end of these instructions. Refer it whenever clarification is required. 1. AD9835 Attachment If you purchased
More informationMP573 Assembly guide. Soldering. MP573 Assembly guide PCB split PCB split. Document revision 2.2 Last modification : 22/08/17
MP573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationInstallation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions)
Installation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions) This tutorial is designed to aid you in installation of a console customs
More informationBuild this Direct Digital Synthesizer "Development Kit" By: Diz Gentzow, W8DIZ
Build this Direct Digital Synthesizer "Development Kit" By: Diz Gentzow, W8DIZ A great tutorial for adding a keypad to the DDS Kit by Bruce, W8BH This manual has been prepared to be read directly on screen.
More informationV6.2 SoftRock Lite Builder s Notes. November 17, 2006
V6.2 SoftRock Lite Builder s Notes November 17, 2006 Be sure to use a grounded tip soldering iron in building the v6.2 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0.1 inch
More informationStandard Kit #1 (3-way switch)
Standard Kit #1 (3-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable
More informationLighthouse Beginner s soldering kit
Lighthouse Beginner s soldering kit Kit contains: 1 x 220 ohm resistor (Red, Red, Black) 1 x 82k ohm resistor (Grey, Red, Orange) 2 x 220k ohm resistors (Red, Red, Yellow) 2 x Diodes 1 x Power switch 1
More informationAssembly Instructions for B7971 Smart Socket
Assembly Instructions for B7971 Smart Socket Identification and installation of the resistors, Fig1 Segment 1,R1, 22k Segment 4, R4, 22k Segment 2, R2, 27k Segment 3, R3, 27k Segment 5, R5, 27k Segment
More informationPenrose Quantizer Assembly Guide
Penrose Quantizer Assembly Guide Schematic and BOM The schematic can be found here: www.sonic-potions.com/public/penrosequantizerschematic.pdf The BOM is available at google docs: Link to BOM Prepare the
More informationBuild Your Own Clone Spring Reverb Kit Instructions
Build Your Own Clone Spring Reverb Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationSUPER Tuna ][+ Builder s Guide
SUPER Tuna ][+ Builder s Guide Ver2.3 Rex Harper W1REX 3/25/2015 The first thing you should do is to familiarize yourself with what you are going to build. The previous 3 pages are schematics of the
More informationRC Interface Controller Board Assembly and Operation
RC Interface Controller Board Assembly and Operation Revision Date: January 17, 2006 SUPERDROIDROBOTS.COM RC Interface Controller Board Accurate content is of the utmost importance to the authors of this
More informationWarm Tube Clock. Before we start, please make sure that you have all required parts that come for the main board :
Warm Tube Clock Assembly Instructions for the main board Introduction Congratulations on your purchase of OSH Nixie Tube Clock. In this document you will see all steps you need to follow in order to successfully
More informationValue Location Qty Potentiometers C1M Distortion 1 A10k Volume 1. Footswitch 3PDT SW1 1. Jacks 1/4 Mono 2 DC Power 1
Distortion BUILD INSTRUCTIONS Thank you for your purchase of our Distortion+ kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same
More informationStandard Kit #1 (5-way switch)
Standard Kit #1 (5-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable
More informationPatton Robotics, LLC.
Patton Robotics LLC Patton Robotics T3 Motherboard Assembly Instructions Version 1.1 Patton Robotics, LLC. 61 Hagan Drive New Hope, PA 18938 Phone: 609-977-5525 Email: pattonrobotics@gmail.com Copyright
More informationDesigned to send specific MIDI information upon each press. Ultra-low current requirement means a single coin cell will last years
PedalSync MIDI Data Module Key Features Discrete MIDI Data delivery in a compact design Designed to send specific MIDI information upon each press Ultra-low current requirement means a single coin cell
More informationAssembling the Heated bed
firepickdelta Assembling the Heated bed Instructions for building the heated bed Written By: Neil Jansen 2017 firepickdelta.dozuki.com Page 1 of 15 Step 1 Exploded View Reference Use the full-size PDF
More informationMain improvements are increased number of LEDs and therefore better temperature indication with one Celsius degree increments.
LED Thermometer V2 (Fahrenheit/Celsius/±1 ) PART NO. 2244754 After completing this great starter kit, users will have a nice interactive LED thermometer. You will learn one principle how temperature can
More information12V Dimmer Kit, version 2
12V Dimmer Kit, version 2 User Manual Description The 12V Dimmer Kit V2 is an especially efficient PWM (pulse-width modulation) controller for 12V loads up to 60 watts. It features a single dial control
More informationEurorack DIY Kit Instructions. All Thonk kits are sold under our standard Terms and Conditions -
MA VCA OVERVIEW For the most recent version of this document please visit http://thonk.co.uk/documents/ma/ For all technical support please visit http://bit.ly/1tl78e0 on Muffwiggler. All Thonk kits are
More informationInstallation tutorial for Console Customs Xbox 360 MaxFire LITE rapid fire Mod Chip.
Installation tutorial for Console Customs Xbox 360 MaxFire LITE rapid fire Mod Chip. This tutorial is designed to aid you in installation of a console customs MaxFire LITE modchip. This tutorial covers
More informationThe Empeg and Riōcar Illumination Kit Installation and User s Manual
The Empeg and Riōcar Illumination Kit Installation and User s Manual Last Updated: October 13, 2005 Table of Contents READ THIS FIRST!!!...1 Introduction to the Installation Process...3 Install the Hijack
More informationCircuit Board Assembly Instructions
Circuit Board Assembly Instructions This document walk you through the assembly of the Base4 Clock v1.2 - v1.3 circuit boards. Important note for kit buyers The color and appearance of the components may
More informationNever power this piano with anything other than a standard 9V battery!
Welcome to the exciting world of Digital Electronics! Who is this kit intended for? This kit is intended for anyone from ages 13 and above and assumes no previous knowledge in the field of hobby electronics.
More informationStarving Student II. Starving Student II. SS2 guide. Written By: 6L guides.diyaudio.com/ Page 1 of 24
SS2 guide Written By: 6L6 2019 guides.diyaudio.com/ Page 1 of 24 INTRODUCTION This is a build guide for the hybrid headphone/pre-amplifier. You can buy a kit at the SSII product listing on the diyaudio
More informationValue Location Qty Transistors 2N5485 Q1, Q2, 4 Q3, Q4 2N5087 Q5 1. Trim Pots 250k VTRIM 1. Potentiometers C500k Speed 1. Toggle Switch On/On Vibe 1
P-90 BUILD INSTRUCTIONS Thank you for your purchase of our P-90 kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same great sound!
More informationElectronics Merit Badge Class 4. 12/30/2010 Electronics Merit Badge Class 4 1
Electronics Merit Badge Class 4 12/30/2010 Electronics Merit Badge Class 4 1 Soldering Safety Note: A Soldering Iron gets hotter than 374 F. Do not touch the soldering iron s metal parts or you will receive
More informationEasy Transmitter. Support ETX_REV5_Manual V2.7 Revised
Easy Transmitter Introduction The Easy Transmitter kit from qrpkits.com provides a basic, crystal controlled transmitter with VXO tuning to provide a small tuning range around the crystal frequency. It
More informationBuild Your Own Clone Mouse Kit Instructions
Build Your Own Clone Mouse Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect. Soldering,
More informationPacific Antenna Easy TR Switch
Pacific Antenna Easy TR Switch Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate receiver
More informationBuilding the Toothpick Audio CW Filter
Building the Toothpick Audio CW Filter Introduction The toothpick is a simple variable bandpass audio filter designed to compliment the Splinter QRPp Trans-Receiver. The filter also contains an audio amplifier
More informationRead This Page First
Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. This is version 8.0 of the manual dated 4/27/2016. There is no need to print out the whole assembly
More informationGF of 9 THE GADGET FREAK FILES CASE #165. Analog Clock Measures Time in Meters
GF 165 04-05-2010 1 of 9 THE GADGET FREAK FILES CASE #165 Analog Clock Measures Time in Meters Alan Parekh took a different approach to time keeping with his electronic clock that registers hours, minutes,
More informationPacific Antenna - Easy TR Switch
Pacific Antenna - Easy TR Switch Kit Description The Easy TR Switch is an RF sensing switch that can be used to switch an antenna between a receiver and transmitter. It also has a second switched pair
More informationBAT DETECTOR A project of the Service Kring JOTA-JOTI.
Manual Bat Detector kit Page 1 of 12 A project of the. Do you like the Bat Detector, do you have great ideas? Tell us, please see how on the last page. Manual Bat Detector kit... 1 Remarks... 2 Introduction...
More informationDuoDrive Nixie Bargraph Kit
Assembly Instructions And User Guide Nixie Bargraph Kit - 1 - REVISION HISTORY Issue Date Reason for Issue Number 1 12 December 2017 New document - 2 - 1. INTRODUCTION 1.1 About Nixie Bargraph Driver IN-9
More informationBuild Your Own Clone Analog Chorus Kit Instructions
Build Your Own Clone Analog Chorus Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationIntroduction. Circuit diagram
Introduction You must have played with a dice at some time, for example when playing Ludo or Monopoly. Dice have existed for a very long time. The first known six-sided dice were found in Iraq and were
More informationGat ew ay T o S pace AS EN / AS TR Class # 07. Colorado S pace Grant Consortium
Gat ew ay T o S pace AS EN / AS TR 2500 Class # 07 Colorado S pace Grant Consortium One Minute Reports: - Can we have two data loggers? - Do you provide us with cameras? {Hardware Checkout after proposal}
More informationCode Practice Oscillator (CPO) For kit building instructions turn to Page 3.
Code Practice Oscillator (CPO) For kit building instructions turn to Page 3. Overview Many thanks for your purchase of this code practice oscillator or CPO, this guide is intended to allow you to quickly
More informationVoice of Saturn Synth Assembly Instruc6ons For PCB v /20/2008 Assembly Instruc=ons v8 09/20/2009
Voice of Saturn Synth Assembly Instruc6ons For PCB v1.03 06/20/2008 Assembly Instruc=ons v8 09/20/2009 1. Recommend Tools and Supplies: Soldering Iron and Solder: A 15 WaG iron will may get the job done,
More informationPacific Antenna Easy Transmitter Kit
Pacific Antenna Easy Transmitter Kit Introduction The Easy Transmitter kit from qrpkits.com provides a crystal controlled transmitter with VXO tuning. The circuit consists of a N3904 based crystal oscillator
More informationXkitz.com XLO-5CP Control Panel for Five Channel Color Light Organ
Xkitz.com XLO-5CP Control Panel for Five Channel Color Light Organ Rev 1.15 An Optional accessory for the Xkitz XLO-5 or XLO-5DC 5 Channel Color Light Organs Introduction This kit contains all the electronics
More informationLA502 Assembly guide Main PCB Resistors - (2)
LA502 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationPacific Antenna Wall Wart Tamer 2.0 Kit
Pacific Antenna Wall Wart Tamer 2.0 Kit Description The Wall Wart Tamer lets you utilize those surplus computer and wall pack power supplies as a clean, adjustable voltage, DC power source for radios and
More informationFigure 1. CheapBot Smart Proximity Detector
The CheapBot Smart Proximity Detector is a plug-in single-board sensor for almost any programmable robotic brain. With it, robots can detect the presence of a wall extending across the robot s path or
More informationQRPGuys SMT Digital Dial/Frequency Counter
QRPGuys SMT Digital Dial/Frequency Counter First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use qrpguys.parts@gmail.com
More informationSTEADY HAND GAME WITH LATCHING LED
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS TEST YOUR HAND-EYE COORDINATION WITH THIS STEADY HAND GAME WITH LATCHING LED Version 2.0
More informationLesson 2: Soldering. Goals
Introduction: Its time to learn how to solder. So you have met all the components needed to make a DIY Gamer, now it s time to put it together. Soldering is joining the components to the printed circuit
More informationThe Useless Machine. Parts Only - Build Guide v0001
TM The Useless Machine Parts Only - Build Guide v0001 For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required: One phillips screwdriver,
More informationDIODE / TRANSISTOR TESTER KIT
DIODE / TRANSISTOR TESTER KIT MODEL DT-100K Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 1988 Elenco Electronics, Inc. Revised 2002 REV-K 753110 DT-100 PARTS LIST If you are a student,
More informationSimple Renard 8 Channel Controller
Simple Renard 8 Channel Controller January 2013 Version 1.00 Board Page 1 of 28 Table of Contents TABLE OF CONTENTS...2 OVERVIEW...3 CONSTRUCTION...3 BASIC TOOLS...3 Soldering Iron...3 Solder...4 Side
More informationPioneer Elite CLD-97 Digital Noise Reduction (DNR) Auto-off Mod DIY Installation Guide
Pioneer Elite CLD-97 Digital Noise Reduction (DNR) Auto-off Mod DIY Installation Guide Background: The CLD-97 laserdisc player has one of the best video quality outputs of any laserdisc player released.
More informationGertboard Assembly Manual Rev 1.1
Gertboard Assembly Manual Rev 1.1 The Gertboard is an add-on GPIO expansion board for the Raspberry Pi computer. It comes with a large variety of components, including buttons, LEDs, A/D converters, DACs,
More informationTek-Bot Remote Control Transmitter Board Construction
Tek-Bot Remote Control Transmitter Board Construction Purpose This tutorial illustrates the procedure for construction of the Transmitter board for the Tek-bot. A Guide to Soldering Many of you have soldered
More informationModification of USB Sound Card for Asterisk app_rpt Use
Modification of USB Sound Card for Asterisk app_rpt Use First off a huge thank you to Steve for providing the original notes on how to modify a USB sound card. (http://images.qrvc.com/usbfob.pdf) These
More informationLED Field Strength Indicator Kit
LED Field Strength Indicator Kit Description The Field Strength Indicator kit from Qrpkits.com provides a visual way to monitor RF fields through the brightness of an LED. It will respond to RF fields
More informationINSTANT ROBOT SHIELD (AXE408)
INSTANT ROBOT SHIELD (AXE408) 1.0 Introduction Thank you for purchasing this Instant Robot shield. This datasheet is designed to give a brief introduction to how the shield is assembled, used and configured.
More informationA Deluxe LED Blinky That You Can Build!
Lux Spectralis A Deluxe LED Blinky That You Can Build! Assembly Instructions Contents Step 1: Parts check... 2 Step 2: Tool check... 3 Step 3: Install the computer chip... 3 Step 4: Install the resistors...
More informationBlue Ring Tester Kit Assembly & User Manual
Blue Ring Tester Kit Assembly & User Manual Alltronics LLC/AnaTek Instruments 2761 Scott Blvd, Santa Clara, CA, 95050, USA March 2015 Edition Tel: 408-778-3868, Fax: 408-778-2558, E mail : tech@alltronics.com
More informationBuild Your Own Clone Classic Phaser Kit Instructions
Build Your Own Clone Classic Phaser Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationAssembly Manual V1R2B-Rev1.0D
Assembly Manual V1R2B-Rev1.0D for 4 State QRP MagicBox - Solid State Transmit/Receive System Designed by: Jim Kortge, K8IQY Copyright 2009-2012 - All rights reserved This system is the result of some brainstorming
More information