Stream Design: From GEOPAK to HEC-Ras
|
|
- Jeffery Johns
- 5 years ago
- Views:
Transcription
1 10 Stream Design: From GEOPAK to HEC-Ras OBJECTIVES Provide you with a general understanding of GEOPAK Cross Section Reports and their capability to generate geometric information for the HecRas program. INTRODUCTION The creation of a stream or river cross sections requires the usage of different tools within the GEOPAK software. The GEOPAK Cross Section Report tool enables us to extract information from the stream cross sections in a format accepted by the HecRas software. The designer should be able to place a basic alignment along the stream and generate existing ground cross sections. These cross sections will be used in the GEOPAK Cross Section Report to format the data accordingly to HecRas GIS format. LAB EXERCISE: IMPORTING STREAM GEOMETRIC DATA TO HEC-RAS > Creating a River Baseline 1. Execute c:\data\geo\vdot\drain1\lab10_v8_selectseries.exe 2. Open the MicroStation file, C:\Data\Geo\VDOT\drain1\Survey_river.dgn 3. Access Store Graphics (MS Menu: Applications > GEOPAK > Road > Geometry > Store Graphics) 4. Enter the information as shown in the dialog below. 5. Press ID Element and select each of the lines that represent the alignment of the river stream until the Store button activates. VDOT GEOPAK Drainage 2011 VDOT 10-1
2 Note Remember to consider that for HEC-RAS the highest station value of a section is the upstream point of the channel. In our example, the river flows from south to north. 6. Click on the Store button. 7. Click OK at the Store Graphics notification dialog. The alignment will be saved into the geometric database and a copy of the generated commands will be written into the ASCII file j101ovd.inp. 8. Close the Store Graphics dialog and delete the MicroStation lines that represented the stream alignment. > Drawing the River Alignment 1. Access the Design and Computation Manager (Applications > GEOPAK > Road > Design & Computation Manager). A secondary dialog box will appear to be used in conjunction with the Design and Computation Manager dialog box. 2. Select the item shown in the dialog box shown below. 3. Click on the Draw Plan and Profile button from the secondary dialog box. 4. Select Chains operation as the Element Type. Each of the chains will be displayed in the list box as shown. Notice that the options that are to be drawn with the chain are already activated. Set the Label Scale to VDOT VDOT GEOPAK Drainage
3 5. To draw the chain, click on the name of the chain: River in the list box. Only click once!! Each time you ID a chain it will be plotted into the design file. 6. Change the Element Type to Stationing and modify the dialog settings as shown. 7. To draw the stationing for the chain, click on the name of the chain: River in the list box. 8. Exit the Plan and Profile Draw dialog box and close the D&C Manager. VDOT GEOPAK Drainage 2011 VDOT 10-3
4 > Existing Ground Cross Sections: Drawing Pattern Lines 1. Access Draw Patterns (Applications > GEOPAK > Road > Cross Sections > Draw Patterns by Station Range). 2. Click Draw Pattern Lines to initiate the plotting of the patterns into the design file. 3. Adjust the length of the pattern lines, using MicroStation commands, at both ends of the bridge just enough to cover the channel section. Note The designer has the option to add, delete or modify patterns lines manually using the Place Line command in MicroStation. GEOPAK identifies any line as a pattern line for cross section plotting by searching for user specified CADD symbology. 4. Close the Draw Pattern Lines dialog box. > Existing Ground Cross Sections: Generating the Stream Cross Sections 1. Open MicroStation file c:\data\geo\vdot\drain1\xsriver.dgn 2. Access Draw Cross Sections from Surfaces (Applications > GEOPAK > Road > Cross Sections). 3. Select the job number: 101 and chain name: RIVER in the Draw Cross Sections dialog. 4. Generate the existing ground cross-sections by populating the dialog boxes as shown below VDOT VDOT GEOPAK Drainage
5 Note The Display Settings for the existing ground line are set to level 1, color 1, style 2, weight 5 5. Click DRAW to generate the cross sections. 6. Data point in the design file to place the cross sections 7. Exit the Draw Cross Sections dialog box. > Review the Cross Sections 1. Select the Cross Section Navigator tool. (Applications > GEOPAK > Road > Cross Sections > Navigator) 2. Use the Cross Section Navigator to browse and check your existing cross sections. 3. Close the XS Navigator dialog box > Exporting to Hec-Ras 1. Access the HEC-RAS report (Applications > GEOPAK > Road > Cross Sections > Reports) VDOT GEOPAK Drainage 2011 VDOT 10-5
6 2. Populate the dialog box as shown below. 3. Click Apply to generate the Hec-Ras cross section geometry file. 4. Exit MicroStation. > Importing Cross Section Data into Hec-Ras 1. Activate Hec-Ras from c:\ data\geo\vdot\drain1\hecras\ras.exe VDOT VDOT GEOPAK Drainage
7 2. Access the included Hec-Ras project: xsriver.prj located in the c:\data\geo\vdot\drain1 3. Access the Geometric data module of Hec-Ras by selecting Edit > Geometric Data from the Hec-Ras pull down menu. 4. Import the cross section data generated by GEOPAK. (File > Import Geometry Data > GIS Format ) 5. Select the file we created from the GEOPAK cross sections: VDOT GEOPAK Drainage 2011 VDOT 10-7
8 6. Review the alignment and layout of the imported cross section data. 7. Review the generated cross sections by clicking on the Cross Section button in the Geometric Data dialog box. Click on the Expand XS Editor button to see a graphical representation of the cross section data VDOT VDOT GEOPAK Drainage
9 8. Save your project data and exit Hec-Ras. VDOT GEOPAK Drainage 2011 VDOT 10-9
CHAPTER 15. Cross Section Sheets. None, except batch processing of an input file.
CHAPTER 15 Cross Section Sheets 15.1 Introduction Objectives Project Manager Menu Bar Application Learn the procedures for laying out cross section sheets. Cross Section Sheets None, except batch processing
More informationEx Existing Ground Cross Sections
Exercise 13-2 1. Open the MicroStation file: t:\de-proj\randolph\j2p0200\data\pattern_shape_j2p0200.dgn. 2. If not already done, attach t:\de-proj\randolph\j2p0200\data\plan_j2p0200.dgn as a reference
More informationGEOPAK V8i SELECTseries 1, Road 2
GEOPAK V8i SELECTseries 1, Road 2 Ohio Department of Transportation October, 2012 Ohio Department of Transportation GEOPAK Road Training Guide for MicroStation V8i SELECTseries 1, October, 2012 The information
More informationOhio Department of Transportation, VBA Documentation
Contents 1.1 Current Versions... 2 1.2 Overview... 3 1.3 Supporting Files and Standards... 4 1.3.1 ODOT_Drainage.cel... 4 1.3.2 ODOT2013.ddb... 5 1.4 ODOT_StormSewerPlan2013.mvba... 6 1.4.1 Mode: Place
More informationHydraulics and Floodplain Modeling Managing HEC-RAS Cross Sections
WMS 10.1 Tutorial Hydraulics and Floodplain Modeling Managing HEC-RAS Cross Sections Modify cross sections in an HEC-RAS model to use surveyed cross section data v. 10.1 Objectives Build a basic HEC-RAS
More informationExample Application C H A P T E R 4. Contents
C H A P T E R 4 Example Application This chapter provides an example application of how to perform steady flow water surface profile calculations with HEC-RAS. The user is taken through a step-by-step
More informationHydraulics and Floodplain Modeling Managing HEC-RAS Cross Sections
v. 9.1 WMS 9.1 Tutorial Hydraulics and Floodplain Modeling Managing HEC-RAS Cross Sections Modify cross sections in an HEC-RAS model to use surveyed cross section data Objectives Build a basic HEC-RAS
More informationPractice Workbook. Cross Sections: Creating, Annotating, and Volumes
Practice Workbook This workbook is designed for use in Live instructor-led training and for OnDemand selfstudy. The explanations and demonstrations are provided by the instructor in the classroom, or in
More informationCE 365K Exercise 2: HEC-RAS Modeling Spring 2014 Hydraulic Engineering Design
CE 365K Exercise 2: HEC-RAS Modeling Spring 2014 Hydraulic Engineering Design This exercise was prepared by Fernando R. Salas and David R. Maidment Introduction In this exercise, we will learn how to setup
More informationRadius Return Select this option to annotate the elevations along the radius return of the intersection.
ODOT_IntersectionDetail.mvba Application Name: Current version: Required MicroStation Version: Required GEOPAK Version: Video Documentation ODOT_IntersectionDetail.mvba V11.07.15 MicroStation XM or V8i
More informationPractice Workbook. Cross Sections: Creating, Annotating, and Volumes. SELECTseries 4 ( ) or newer
Practice Workbook This workbook is designed for use in Live instructor-led training and for OnDemand self study. The explanations and demonstrations are provided by the instructor in the classroom, or
More informationCreate all plan and profile sheets in the current drawing. Create all plan and profile sheets in individual drawings.
NOTES Module 18 Roadway Plan Production In this module, you learn how to work with Roadway Plan Production tools in AutoCAD Civil 3D. The Plan Production tools are used to automate the generation of plan
More informationChapter 6 Title Blocks
Chapter 6 Title Blocks In previous exercises, every drawing started by creating a number of layers. This is time consuming and unnecessary. In this exercise, we will start a drawing by defining layers
More informationUnit 15: Using Symbols and Attributes
Unit 15: Using Symbols and Attributes Overview Many electronics drawings use the same geometry over and over. The resistor symbol, commonly found on printed circuit board drawings, is one example. AutoCAD
More informationRRR Design & Modeling with the FDOT Civil 3D State Kit
RRR Design & Modeling with the FDOT Civil 3D State Kit Mike Racca - CADD Applications Development Specialist Production Support Office CADD 605 Suwannee St - MS 40, Tallahassee, Florida 32399 Session Objectives:
More informationState of Florida Department of Transportation. FDOT Traffic Plans. Signing & Pavement Markings (CE ) Signalization (CE ) Lighting
State of Florida Department of Transportation FDOT Traffic Plans Signing & Pavement Markings (CE-11-0117) Signalization (CE-11-0119) Lighting (CE-11-0118) User Training Manual October 2017 PRODUCTION SUPPORT
More informationX11-Using the New Civil Geometry Tools
X11-Using the New Civil Geometry Tools Joe Waxmonsky, PE Bentley Civil 2010 Bentley Systems, Incorpo ora 2010 Bentley Systems, Incorpora 2010 Nordic Civil Geometry 2 WWW.BENTLEY.COM Roads and Bridges 2010
More informationUsing Dynamic Views. Module Overview. Module Prerequisites. Module Objectives
Using Dynamic Views Module Overview The term dynamic views refers to a method of composing drawings that is a new approach to managing projects. Dynamic views can help you to: automate sheet creation;
More informationDisplay and Draw Features
CHAPTER 7 Display and Draw Features 7.1 Overview Feature / Function Tool Display or draw DTM features, such as contours, triangles, lattices, voids, islands, etc. DTM Menu Bar Load > DTM Features GEOPAK
More informationSheet Metal Punch ifeatures
Lesson 5 Sheet Metal Punch ifeatures Overview This lesson describes punch ifeatures and their use in sheet metal parts. You use punch ifeatures to simplify the creation of common and specialty cut and
More informationUnit 15: Using Symbols and Attributes
Unit 15: Using Symbols and Attributes Overview Many mechanical drawings use the same geometry over and over. The SI symbol, commonly found on Metric drawings, is one example. AutoCAD allows you create
More informationAdvanced Topics Using the Sheet Set Manager in AutoCAD
Advanced Topics Using the Sheet Set Manager in AutoCAD Sam Lucido Haley and Aldrich, Inc. GEN15297 Do you still open drawings one at a time? Do you print drawings one at a time? Do you update the index
More informationWhat's the Latest with InRoads Storm & Sanitary SS1?
What's the Latest with InRoads Storm & Sanitary SS1? Joe Waxmonsky, Bentley Civil Why implement S&S? To avoid this: 2 WWW.BENTLEY.COM Single-source it 3 WWW.BENTLEY.COM StormCAD reads S&S files! StormCAD
More informationAssignment 13 CAD Mechanical Part 2
Assignment 13 CAD Mechanical Part 2 Objectives In this assignment you will learn to apply the hatch and break commands along with commands previously learned. General Instructions Hatching 1. When AutoCAD's
More informationField Observations and One-Dimensional Flow Modeling of Summit Creek in Mack Park, Smithfield, Utah
Sediment Transport Workshop, Utah State University, 1 August 2017 Field Observations and One-Dimensional Flow Modeling of Summit Creek in Mack Park, Smithfield, Utah I. Goals for learning and discussion:
More informationCorridors. To create a corridor you must have an alignment (baseline), a profile (existing or proposed), and an assembly.
Corridors To create a corridor you must have an alignment (baseline), a profile (existing or proposed), and an assembly. Alignments You have 2 choices in defining an alignment: (1) Alignments > Create
More informationCivil Product Update. Derricke Gray, Product Manager Bentley Civil Americas
Civil Product Update Derricke Gray, Product Manager Bentley Civil Americas 1 WWW.BENTLEY.COM 2016 Bentley Systems, Incorporated 2016 Bentley Systems, Incorporated Agenda Civil Update o Where we are at
More informationExercise 1: The AutoCAD Civil 3D Environment
Exercise 1: The AutoCAD Civil 3D Environment AutoCAD Civil 3D Interface Object Base Layer Object Component Layers 1-1 Introduction to Commercial Site Grading Plans AutoCAD Civil 3D Interface AutoCAD Civil
More informationOpenRail SELECTseries 4 - Managing Geometry and Corridor Modeling
2015 Bentley Systems, Incorporated OpenRail SELECTseries 4 - Managing Geometry and Corridor Modeling Robert Nice Senior Application Engineer Agenda: Why work in SELECTseries 4? Moving to SELECTseries 4
More informationThe Basics. HECRAS Basis Input. Geometry Data - the basics. Geometry Data. Flow Data. Perform Hydraulic Computations. Viewing the Output
The Basics HECRAS Basis Input Geometry Data. Flow Data. Perform Hydraulic Computations by G. Parodi WRS ITC The Netherlands Viewing the Output ITC Faculty of Geo-Information Science and Earth Observation
More informationFundamentals of ModelBuilder
Fundamentals of ModelBuilder Agenda An Overview of Geoprocessing Framework Introduction to ModelBuilder Basics of ArcToolbox Using ModelBuilder Documenting Models Sharing Models with Others Q & A Geoprocessing
More informationProject Exercise 5 Cells and Cell Library
Project Exercise 5 Cells and Cell Library This project exercise provides step-by-step instructions for creating the design shown in Figure C5-1. The intent is to guide you in creating and using cells.
More informationImport/Export of tendons in module StatiCa Tendon
IDEA Tutorial Import/Export of tendons in module StatiCa Tendon by using formats DXF, TXT and table format Import/Export of tendons in module StatiCa Tendon 1 Contents 1. Terminology... 2 2. Import...
More informationGIS Module GMS 7.0 TUTORIALS. 1 Introduction. 1.1 Contents
GMS 7.0 TUTORIALS 1 Introduction The GIS module can be used to display data from a GIS database directly in GMS without having to convert that data to GMS data types. Native GMS data such as grids and
More informationEstimated Time Required to Complete: 45 minutes
Estimated Time Required to Complete: 45 minutes This is the first in a series of incremental skill building exercises which explore sheet metal punch ifeatures. Subsequent exercises will address: placing
More informationv. 8.0 GMS 8.0 Tutorial GIS Module Shapefile import, display, and conversion Prerequisite Tutorials None Time minutes
v. 8.0 GMS 8.0 Tutorial Shapefile import, display, and conversion Objectives Learn how to import and display shapefiles with and without ArcObjects. Convert the shapefiles to GMS feature objects. Prerequisite
More informationBentley Civil Update and Direction
www. bentley. com Bentley Civil Update and Direction Mike Wilson Director, Software Development, Bentley Civil The cast of characters this year Bentley Civil Mike Wilson that would be me Director, Software
More informationMontana Association of Registered Land Surveyors Conference 2013
AutoCAD CIVIL 3D Survey Features - Field to Finish This session is an introduction to the Civil 3D Survey Tools. We will cover some basics of working with Survey Databases and Automated Linework. We will
More informationBentleyuser.dk Årsmøde 2010 Nordic Civil 2010
Bentleyuser.dk Årsmøde 2010 Nordic Civil 2010 8.-10. November 2010, Munkebjerg Hotel, Vejle Workshop - X9 Resurfacing and Overlay Tools InRoads V8i Presenter: Joe Waxmonsky, P.E., Bentley Systems USA Bentley
More informationBatch Processing Converting images in a folder to JPEG
Batch Processing Converting images in a folder to JPEG Request I would like to convert multiple RAW images (NEF files) to JPEG images all at once Response You can use a Batch Process to convert all RAW
More informationAutodesk Advance Steel. Drawing Style Manager s guide
Autodesk Advance Steel Drawing Style Manager s guide TABLE OF CONTENTS Chapter 1 Introduction... 5 Details and Detail Views... 6 Drawing Styles... 6 Drawing Style Manager... 8 Accessing the Drawing Style
More informationAEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here.
AEROPLANE Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Arc, Add Relations, Dimensioning), Extrude, Assemblies and
More informationAdvance Steel. Drawing Style Manager s guide
Advance Steel Drawing Style Manager s guide TABLE OF CONTENTS Chapter 1 Introduction...7 Details and Detail Views...8 Drawing Styles...8 Drawing Style Manager...9 Accessing the Drawing Style Manager...9
More informationRevit Structure 2012 Basics:
SUPPLEMENTAL FILES ON CD Revit Structure 2012 Basics: Framing and Documentation Elise Moss autodesk authorized publisher SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Structural
More informationAn Introduction to Dimensioning Dimension Elements-
An Introduction to Dimensioning A precise drawing plotted to scale often does not convey enough information for builders to construct your design. Usually you add annotation showing object measurements
More informationFull Contents. Essentials, Workbook
Section 1: Overview Essentials 1.1 Introduction... 3 Learning InRoads... 3 Basic Rules... 3 How to Use This Guide... 4 Section Breakdown... 5 Section 1: Overview Essentials... 5 Section 2: Production Essentials...
More informationAECOsim Building Designer. Quick Start Guide. Chapter A08 Space Planning Bentley Systems, Incorporated
AECOsim Building Designer Quick Start Guide Chapter A08 Space Planning 2012 Bentley Systems, Incorporated www.bentley.com/aecosim Table of Contents Space Planning...3 Sketches... 3 SpacePlanner... 4 Create
More informationCast Unit Drawings Tekla Structures 11.0 Basic Training August 25, 2005
Tekla Structures 11.0 Basic Training August 25, 2005 Copyright 2005 Tekla Corporation Contents 11... 3 11.1 Create...4 Define cast unit drawing properties for beams...4 Create a cast unit drawing for a
More informationExisting and Design Profiles
NOTES Module 09 Existing and Design Profiles In this module, you learn how to work with profiles in AutoCAD Civil 3D. You create and modify profiles and profile views, edit profile geometry, and use styles
More informationVirtual components in assemblies
Virtual components in assemblies Publication Number spse01690 Virtual components in assemblies Publication Number spse01690 Proprietary and restricted rights notice This software and related documentation
More informationStratigraphy Modeling Boreholes and Cross. Become familiar with boreholes and borehole cross sections in GMS
v. 10.3 GMS 10.3 Tutorial Stratigraphy Modeling Boreholes and Cross Sections Become familiar with boreholes and borehole cross sections in GMS Objectives Learn how to import borehole data, construct a
More informationRevit Structure 2014 Basics
Revit Structure 2014 Basics Framing and Documentation Elise Moss Authorized Author SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit
More informationCorridors To create a corridor you must have an alignment (baseline), a profile (existing or proposed), and an assembly.
Corridors 2018-2019 To create a corridor you must have an alignment (baseline), a profile (existing or proposed), and an assembly. Alignments You have 2 choices in defining an alignment from scratch: (1)
More informationLattice Design Solid Infills. Tutorial_V2 : 13,0600,1489,1616(SP6)
Lattice Design Solid Infills Tutorial_V2 : 13,0600,1489,1616(SP6) Introduction 3DXpert for SOLIDWORKS includes tools for creating optimized structures, using Lattices and Infills. Infills are structures
More informationA Practical Guide to Carlson Survey 2014
A Practical Guide to Carlson Survey 2014 Level 1 Rick Ellis A Cadapult Press Publication Copyright Copyright Cadapult Press, Inc. 2014 All rights reserved. No part of this publication may be reproduced
More informationFrom Nothing to Something using AutoCAD Electrical
From Nothing to Something using AutoCAD Electrical Todd Schmoock Synergis Technologies MA2085-L: You purchased AutoCAD Electrical, or are thinking about purchasing it, but you do not know how to use it.
More informationDrawing output in imos ix 2017 SR2. Date of creation: March 2018; last changes Version used: ix 2017 SR2
Drawing output in imos ix 2017 SR2 Date of creation: March 2018; last changes 13.04.2018 Version used: ix 2017 SR2 We make every effort to ensure the content of this document is complete, accurate and
More information1. Create a 2D sketch 2. Create geometry in a sketch 3. Use constraints to position geometry 4. Use dimensions to set the size of geometry
2.1: Sketching Many features that you create in Fusion 360 start with a 2D sketch. In order to create intelligent and predictable designs, a good understanding of how to create sketches and how to apply
More informationSheet Metal OverviewChapter1:
Sheet Metal OverviewChapter1: Chapter 1 This chapter describes the terminology, design methods, and fundamental tools used in the design of sheet metal parts. Building upon these foundational elements
More informationObjectives Learn how to import and display shapefiles with and without ArcObjects. Learn how to convert the shapefiles to GMS feature objects.
v. 10.1 GMS 10.1 Tutorial Importing, displaying, and converting shapefiles Objectives Learn how to import and display shapefiles with and without ArcObjects. Learn how to convert the shapefiles to GMS
More informationIntroduction to Parametric Modeling AEROPLANE. Design & Communication Graphics 1
AEROPLANE Design & Communication Graphics 1 Object Analysis sheet Design & Communication Graphics 2 Aeroplane Assembly The part files for this assembly are saved in the folder titled Aeroplane. Open an
More informationModule 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated)
Inventor (5) Module 2: 2-1 Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated) In this tutorial, we will learn how to build a 3D model
More informationPOWER DEMAND FOR MULTIPLE ZONES
IDA Indoor Climate and Energy Basic Course POWER DEMAND FOR MULTIPLE ZONES Guide Copyright EQUA Simulation AB February 2018 Purpose This is the second part of the IDA ICE basic course 1. You learn how
More informationAECOsim Building Designer. Quick Start Guide. Chapter 2 Making the Mass Model Intelligent Bentley Systems, Incorporated.
AECOsim Building Designer Quick Start Guide Chapter 2 Making the Mass Model Intelligent 2012 Bentley Systems, Incorporated www.bentley.com/aecosim Table of Contents Making the Mass Model Intelligent...3
More informationFDESIGN TUTORIALS - MAIN-Index. Index 1 SECTIONS DRAWINGS. 2 SURFACES DRAWINGS. 3 INTERIM PRODUCTS DRAWINGS. 4 MODEL DRAWINGS. 5 OTHER TOOLS.
FDESIGN TUTORIALS - MAIN-Index Index 1 SECTIONS DRAWINGS. 2 SURFACES DRAWINGS. 3 INTERIM PRODUCTS DRAWINGS. 4 MODEL DRAWINGS. 5 OTHER TOOLS. 1 Tasks 1.01 Format and Title Block. 1.02 FORAN Sections. 1.03
More informationIntroduction to Autodesk Inventor for F1 in Schools (Australian Version)
Introduction to Autodesk Inventor for F1 in Schools (Australian Version) F1 in Schools race car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital
More informationRelative Coordinates
AutoCAD Essentials Most drawings are created using relative coordinates. This means that the next point is set from the last point drawn. The last point drawn is stored as temporary 0,0". AutoCAD uses
More informationSheets Happen! Using the Sheet Set Manager
Sheets Happen! Using the Sheet Set Manager Westwood Professional Services June 2007 Using AutoCAD s Sheet Set Manager Introduction The Sheet Set Manager organizes, displays, and manages sheet sets, a named
More informationIntroduction to Sheet Metal Features SolidWorks 2009
SolidWorks 2009 Table of Contents Introduction to Sheet Metal Features Base Flange Method Magazine File.. 3 Envelopment & Development of Surfaces.. 14 Development of Transition Pieces.. 23 Conversion to
More informationFull Contents. Survey V8.08 Essentials
Section 1: Overview Essentials 1.1 Introduction... 3 Learning InRoads Survey... 3 Basic Rules... 3 How to Use This Guide... 4 Section Breakdown... 5 Section 1: Overview Essentials... 5 Section 2: Production
More information1 Setup Guide. Before You Install MicroStation Descartes
1 Setup Guide This guide informs you of the minimal requirements to install and run MicroStation Descartes and also provides guidance on installation. You will find information on how to configure and
More informationA Quick Spin on Autodesk Revit Building
11/28/2005-3:00 pm - 4:30 pm Room:Americas Seminar [Lab] (Dolphin) Walt Disney World Swan and Dolphin Resort Orlando, Florida A Quick Spin on Autodesk Revit Building Amy Fietkau - Autodesk and John Jansen;
More informationAnsoft Designer Tutorial ECE 584 October, 2004
Ansoft Designer Tutorial ECE 584 October, 2004 This tutorial will serve as an introduction to the Ansoft Designer Microwave CAD package by stepping through a simple design problem. Please note that there
More informationPractice Workbook. Create 2D Plans from 3D Geometry in a Civil Workflow
Practice Workbook This workbook is designed for use in Live instructor-led training and for OnDemand selfstudy. The explanations and demonstrations are provided by the instructor in the classroom, or in
More informationAutodesk. AutoCAD Architecture Fundamentals. Elise Moss SDC PUBLICATIONS. Schroff Development Corporation
Autodesk AutoCAD Architecture 2008 Fundamentals Elise Moss SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com Lesson 3 Floor Plans The floor plan is central to any
More informationPLA Planner Student Handbook
PLA Planner Student Handbook TABLE OF CONTENTS Student Quick Start Guide PLA Planner Overview...2 What is PLA Planner?...4 How do I access PLA Planner?...4 Getting to Know PLA Planner Home...5 Getting
More informationby Jonathan Pickup fourth edition written with version 2013 Vectorworks Landmark Tutorial Manual SAMPLE
kramdnal by Jonathan Pickup fourth edition written with version 2013 Vectorworks Landmark Tutorial Manual Table of Contents Introduction... iii Project 1: Landscape Area Analysis...1 Project 2: Quick Domestic
More informationStep It Up a Rung from AutoCAD Designs to AutoCAD Electrical
Step It Up a Rung from AutoCAD Designs to AutoCAD Electrical Todd Schmoock Synergis Technologies MA4762-L: AutoCAD Electrical has proven to be easy for creating electrical controls system designs. It has
More informationIDEA Corbel 8. User guide. IDEA Corbel User Guide
IDEA Corbel User Guide IDEA Corbel 8 User guide IDEA Corbel User Guide Content 1.1 Program requirements... 3 1.2 Installation guidelines... 3 2 Basic Terms... 4 3 User interface... 5 3.1 Control of view
More informationPrasanth. Lathe Machining
Lathe Machining Overview Conventions What's New? Getting Started Open the Part to Machine Create a Rough Turning Operation Replay the Toolpath Create a Groove Turning Operation Create Profile Finish Turning
More informationSubdivision Cross Sections and Quantities
NOTES Module 11 Subdivision Cross Sections and Quantities Quantity calculation and cross section generation are required elements of subdivision design projects. After the design is completed and approved
More informationAASHTOWare Bridge Rating Training. T6 Truss Cross Sections and Graphics (BrR 6.4)
AASHTOWare Bridge Rating Training T6 Truss Cross Sections and Graphics (BrR 6.4) This example describes how to define a Channelbox truss cross section with stacking plates on either side of channel webs
More informationOzE Field Modules. OzE School. Quick reference pages OzE Main Opening Screen OzE Process Data OzE Order Entry OzE Preview School Promotion Checklist
1 OzE Field Modules OzE School Quick reference pages OzE Main Opening Screen OzE Process Data OzE Order Entry OzE Preview School Promotion Checklist OzESchool System Features Field unit for preparing all
More informationStatistics 101: Section L Laboratory 10
Statistics 101: Section L Laboratory 10 This lab looks at the sampling distribution of the sample proportion pˆ and probabilities associated with sampling from a population with a categorical variable.
More informationBentley Rail Track Update
Bentley Rail Track Update Robert Nice Bentley Systems UK Recent Past and Near Future Today, I will discuss recent enhancements to Bentley Rail Track. Some of these enhancements you may be very familiar
More informationLesson 4 Holes and Rounds
Lesson 4 Holes and Rounds 111 Figure 4.1 Breaker OBJECTIVES Sketch arcs in sections Create a straight hole through a part Complete a Sketched hole Understand the Hole Tool Use Info to extract information
More informationLearning Guide. ASR Automated Systems Research Inc. # Douglas Crescent, Langley, BC. V3A 4B6. Fax:
Learning Guide ASR Automated Systems Research Inc. #1 20461 Douglas Crescent, Langley, BC. V3A 4B6 Toll free: 1-800-818-2051 e-mail: support@asrsoft.com Fax: 604-539-1334 www.asrsoft.com Copyright 1991-2013
More informationRevit Structure 2013 Basics
Revit Structure 2013 Basics Framing and Documentation Elise Moss Supplemental Files SDC P U B L I C AT I O N S Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Tutorial
More informationMy Star Cards - StarCash
My Star Cards - StarCash Table of Contents StarCash... 1 Star Cash... 1 StarCash Menu... 1 Related topics... 2 Order StarCash cards... 2 Order StarCash Cards... 2 StarCash Order List Screen... 2 StarCash
More informationOptimizing Digital Drawing Files and BIM Models for Measurement and Estimating
Optimizing Digital Drawing Files and BIM Models for Measurement and Estimating Simon Lovegrove MRICS, AAIQS - Exactal CM4228 Drawing file formats issued for measurement and estimating purposes range from
More informationPart Design. Sketcher - Basic 1 13,0600,1488,1586(SP6)
Part Design Sketcher - Basic 1 13,0600,1488,1586(SP6) In this exercise, we will learn the foundation of the Sketcher and its basic functions. The Sketcher is a tool used to create two-dimensional (2D)
More informationCHAPTER 8 Electronic Deliverables TABLE OF CONTENTS
CHAPTER 8 Electronic Deliverables TABLE OF CONTENTS CHAPTER 8... 3 8.1 Specifications for Electronic Data Deliverables... 3 8.1.1 Introduction / Purpose... 3 8.2 Background... 4 8.3 Scope... 5 8.4 File
More informationTerrain Modeling with ArcView GIS
What You Will Need: A Pentium class PC with 32 MB of RAM (minimum) and 100 MB of free hard drive space, ArcView GIS 3.1 or higher and WinZip or an equivalent program, and an Internet connection. Data and/or
More information4. GAMBIT MENU COMMANDS
GAMBIT MENU COMMANDS 4. GAMBIT MENU COMMANDS The GAMBIT main menu bar includes the following menu commands. Menu Item File Edit Solver Help Purposes Create, open and save sessions Print graphics Edit and/or
More informationWelcome to Solid Edge University
#SEU15 Welcome to Solid Edge University Realize innovation. State-of-the-Art Drafting, Made Even Better Investing in What You Need General Workflow Dimension Enhancements Annotation Enhancements Page 2
More informationThis document describes the new features of MTpro version as compared to MTpro
New features in MTpro 3.6 This document describes the new features of MTpro version 3.6.0.0 as compared to MTpro 3.5.0.0. Table of contents 1 General... 2 2 New contents... 3 2.1 New CAD models... 3 2.2
More informationSection Table of Contents: Section 16.0
Section 16.0 Table of Contents: Section 16.0 Overview - Section 16.0... 16.0-3 Plotting Single Sheets... 16.0-3 Publishing... 16.0-5 Creating DWFs or PDFs (with Sheet Sets)... 16.0-6 Overview - Section
More information3D Modeling Demonstration
2014 Bentley Systems, Incorporated 3D Modeling Demonstration Derricke Gray, Product Manager Bentley Civil Americas ESS Statewide Rollouts: 3D Modeling Engineering Content Management (ProjectWise) 2 WWW.BENTLEY.COM
More informationGenerations Automatic Stand-Alone Lace By Bernie Griffith Generations Software
We are going to create an open Italian lace. Generations software products provide advanced image processing features allowing for the creation of stand-alone lace with just a few simple techniques. A
More informationM TE S Y S LT U A S S A
Dress-Up Features In this lesson you will learn how to place dress-up features on parts. Lesson Contents: Case Study: Timing Chain Cover Design Intent Stages in the Process Apply a Draft Create a Stiffener
More information