IN-DIE TAPPING TOOLS TECHNICAL INFORMATION MANUAL
|
|
- Gwendoline West
- 5 years ago
- Views:
Transcription
1 IN-DIE TAPPING TOOLS TECHNICAL INFORMATION MANUAL CALL TOLL FREE: FAX: Danly IEM, A Division of Connell Limited Partnership
2 THIS MANUAL CONTAINS INFORMATION APPLICABLE TO THE FOLLOWING IN-DIE TAPPING TOOL MODELS: HY1024 ME1024 LP25M6 (Patent # ) TABLE OF CONTENTS PAGE NUMBER PRODUCT SPECIFICATIONS 2 ACCESSORIES 5 TAPPING DEPTH/MATERIAL THICKNESS CHARTS 8 FORMING TAP PRE-HOLE SIZE CHARTS 9 APPLICATION DRAWINGS 11 DESIGNING A CAM DRIVER 38 RAPID T.A.P. CAM DESIGN SOFTWARE INTRODUCTION 39 TROUBLE SHOOTING 40 1
3 HY1024 Series for Hydraulic Presses HY1024 Product Features The HY is the smallest and most compact of the tapping tools. The HY1024 is an economical solution for tapping from the top down in a hydraulic press. Since the HY1024 is not cam actuated, the press controls the acceleration and tap speed. The HY1024 will tap size #0 - #12 or up to M5 and typically runs at production rates between strokes per minute up to a maximum 200 (SPM) rate based on strip material, tap size and tap pitch. By utilizing multiple tools in place of one special tapping tool, you can control flexibility in the stamping operation and greatly reduce downtime due to unscheduled maintenance. NOTES: The HY1024 tapping tool cannot be used in a mechanical press. See the ME1024 or the LP25M6 for applications requiring use in a mechanical press. HY1024 footprint dimensions Notes: Tapping depth/maximum material thickness can be found on Page 8. Metric dimensions are in italics. 2
4 ME1024 Series for Mechanical Presses Product Features The ME1024 is a simple and compact tool with a small footprint for tapping top down in a mechanical or hydraulic press. The ME1024 utilizes a cam driver to control tool acceleration. The ME will tap size #0 - #12 or up to M5 and typically runs at production rates between strokes per minute up to a maximum of 200 (SPM) based on strip material, tap size and pitch. The cam driver is designed as a separate functional piece to maximize die design flexibility and take the sinusoidal motion that is inherent with mechanical presses and turn it into a rotary tapping motion. The cam driver mounts easily on a punch plate or upper die shoe above the tapping tool. The cam driver is application specific and can be manufactured by using the free Rapid TAP CAD design software. By utilizing multiple tools in place of one special tapping tool, you can control flexibility in the stamping operation and greatly reduce downtime due to unscheduled maintenance. ME1024 A = TAPPING STROKE ME1024 footprint dimensions Notes: Tapping depth/maximum material thickness can be found on Page 8. All dimensions are in inches. 3
5 LP25M6 & LP516M8 Series for Mechanical Presses LP25M6 Product Features The LP is the most versatile tool with a simple and compact design for tapping top down, bottom up or at any angle. The LP utilizes a cam driver to control tool acceleration and tap speeds. The LP25M6 will tap size #0-1/4 or M6 and the LP516M8 will tap 1/4" - 5/16" or M8 while making either right or left-hand threads. The LP typically runs at production rates between strokes per minute up to a maximum of 100 (SPM) based on strip material, tap size and pitch. The cam driver is designed as a separate functional piece to maximize die design flexibility and take the sinusoidal motion that is inherent with mechanical presses and turn it into a rotary tapping motion. The cam driver mounts easily on a punch plate on the upper die shoe above the tapping unit to provide the proper amount of tap acceleration and a positive return. The cam driver is application-specific and can be manufactured by using the free Rapid TAP CAD design software. By utilizing multiple tools in place of one special tapping tool, you can control flexibility in the stamping operation and greatly reduce downtime due to unscheduled maintenance. LP Cam Driver profile Important Note The shut height from the bottom of the upper shoe to the mounting surface of the unit cannot be less than 3.775", unless modified (see installation manual). LP25M6 & LP516M8 footprint dimensions NOTE A: Dowel pin holes ±0.001 Fastener holes ±0.005 Notes: Footprint dimensions are identical for both units. However, performance variations exist between the two units. Consult the Rapid Tap software. Tapping depth/maximum material thickness can be found on Page 8. All dimensions are in inches. 4
6 LP Extensions Accessories and Replacement Parts Some applications require a wide strip width incorporating a tapped hole located a distance from the edge of the material. The LP integrates modular extensions in combination with a standard tool to provide flexibility in design and off-the-shelf type components. The standard Cam Extension provides over 9" of extra length while the extra long extension provides over 19". All components are made from the best materials for maximum life and performance. LP STANDARD EXTENSION LP EXTRA LONG EXTENSION Notes: All dimensions are in inches. 5
7 Taps are sold in packs of 12. Accessories and Replacement Parts Forming Taps Product Features The special forming taps used in the in-die taping units are available in inch and metric standard sizes listed below. All forming taps are sold with a TiN coating as standard. Other coatings for special material applications are available on request. Forming taps provide a superior quality and finish of thread, with no chip formation. INCH SIZES Part Number Shank Size 1 Tap Size & D Limit R Small RH3 R Small RH5 R Small RH7 R Small RH5 R Small RH5 R Small RH5 R Small RH5 R Small RH7 R Small RH5 R Small RH7 R Small RH6 R Small RH8 R Small RH6 R Small RH6 R Small RH6 R Medium 1/ RH6 R Large 1/ RH6 R Medium 1/ RH6 R Large 1/ RH6 R Large 5/16-32 RH6 R Large 5/16-24 RH6 R Large 5/16-18 RH7 METRIC SIZES Part Number Shank Size 1 Tap Size & D Limit R Small M2.0 x.40 D5 R Small M2.5 x.45 D5 R Small M3.0 x.50 D5 R Small M3.5 x.60 D6 R Small M4.0 x.70 D6 R Small M5.0 x.80 D7 R Medium M6.0 x 1.00 D8 R Large M6.0 x 1.00 D8 R Large M8.0 x 1.00 D8 R Large M8.0 x 1.25 D8 Standard Stock Taps are TiN Coated Special Tap Sizes, Pitches and Coatings are Available per Quotation 1 Tap diameter shank size application: Small 0 - #12 (M2 M5) diameter taps: use in HY1024, ME1024, LP25M6 Medium ¼" (M6) diameter taps: use in LP25M6 Large ¼" 5/16 (M6 - M8) diameter taps: use in LP516M8 6
8 Accessories and Replacement Parts Pitch Inserts/Tap Holders Product Features Pitch inserts are interchangeable components of the tapping operation and are specific to the tap pitch of the tapped hole. Each pitch insert contains a tap holder with a quick release depression collar. Taps can easily be changed within seconds in most applications. For applications needing a little extra reach to tap inside an embossment, a pitch insert extension can be made specific to your needs. Our engineering department will work with you on your specific application. INCH SIZES Tap Part Part Part Holder Number Number Number Pitch Size 1 for for for HY/ME1024 LP25ME LP516M8 56 Small R R Small R R Small R R Small R R Small R R Medium R Large R Small R R Large R Medium R Large R Large R METRIC SIZES Tap Part Part Part Holder Number Number Number Pitch Size 1 for for for HY/ME1024 LP25ME LP516M mm Small R R mm Small R R mm Small R R mm Small R R mm Small R R mm Small R R mm Medium R mm Large R mm Large R Pitch insert for non-standard sizes or pitches are by quotation. 1 Tap diameter shank size application: Small 0 - #12 (M2 M5) diameter taps: use in HY1024, ME1024, LP25M6 Medium ¼" (M6) diameter taps: use in LP25M6 Large ¼" 5/16" (M6 - M8) diameter taps: use in LP516M8 7
9 Maximum Tapping Depth/ Material Thickness MAXIMUM MATERIAL THICKNESS (T) - INCH Size and HY & ME Pitch 1024 LP25M6 LP516M / / /16x32UN /16x24UN /16x18UN MAXIMUM MATERIAL THICKNESS (T) - METRIC Size and HY & ME Pitch 1024 LP25M6 LP516M8 M2 x M2.5 x M3 x M3 x M3.5 x M4 x M5 x M5 x M6 x M8 x M8 x NOTE: Maximum material thickness (T) includes extrusion height and.020 inch (or 0.5mm) gap between the tip of the tap and the top of the material stock. 8
10 Pre-Hole Sizes METRIC COLDFORMING TAPS 65% THREAD 70% THREAD 75% THREAD TAP SIZE/ THEOR. HOLE THEOR. HOLE THEOR. HOLE PITCH (mm) SIZE (mm) SIZE (mm) SIZE (mm) M3 x M3 x M3.5 x M4 x M4 x M4.5 x M5 x M5 x M6 x M6.3 x M7 x M8 x M8 x M10 x M10 x M12 x M12 x NOTE: The shaded pre-hole sizes in the above table have been changed, as they were incorrectly calculated in earlier versions of this manual. PRE-HOLE SIZE CALCULATION Hole size = Basic Major Diameter - Percent of Full Thread x mm Pitch Example: Find the theoretical pre-hole punch size for M8 x 1.25mm to produce 65% thread: Hole size = x 1.25 / = = 7.448mm NOTE: Tapping an undersize hole may result in tap breakage due to excessive torque. As a starting recommendation, 65% thread should be considered. Tapping over 75% of thread is not recommended. 9
11 Pre-Hole Sizes INCH COLDFORMING TAPS 65% THREAD 70% THREAD 75% THREAD TAP SIZE/ THEOR. HOLE THEOR. HOLE THEOR. HOLE PITCH (in) SIZE (in) SIZE (in) SIZE (in) 0 80 NC NC NF NC NF NC NF NC NF NC NF NC NF NC NF NC NF NC NF /4 20 NC /4 28 NF /16 18 NC /16 24 NF /8 16 NC /8 24 NF /16 14 NC /16 20 NF /2 13 NC /2 20 NF PRE-HOLE SIZE CALCULATION Hole size = Basic Major Diameter - Percent of Full Thread Number of Threads per Inch Example: Find the theoretical pre-hole punch size for 1/4-20 to produce 65% thread: Hole size = x 65/20 = = inches NOTE: Tapping an undersize hole may result in tap breakage due to excessive torque. As a starting recommendation, 65% thread should be considered. Tapping over 75% of thread is not recommended. 10
12 FIGURE #1 LOW PROFILE TOOLS TAPPING FROM THE BOTTOM UP THIS DRAWING IS SHOWING THE LP25M6 IN THE CLOSED POSITION. NITROGEN SPRING CAN BE USED TO ELIMINATE TOO LONG OF A DIE SPRING. SPRING TRAVEL IS BASED ON TAPPING STROKE, PLUS PRELOAD ON MATERIAL BEFORE TAPPING. (PRELOAD WILL INSURE PROPER STRIPPING FOR TAPPING.) CUSTOMER CAN USE A BRIDGE STRIPPER INSTEAD OF A SPRING STRIPPER IF DESIRED. MATERIAL UPPER DIE MATERIAL SPACER BLOCK (IF NEEDED) STRIPPER DIE DIE 1/4 S.H.C.S. 8 PLACES CAM BOTTOM DIE MACHINED POCKETS FOR CAM CLEARANCE MACHINE POCKET IN DIE SET FOR DESIRE HEIGHT. HEEL BLOCK MACHINE GROOVE TO ALLOW PASSAGE FOR GREASE GUN. D
13 FIGURE #2 LOW PROFILE TOOLS TAPPING FROM THE TOP DOWN LP25M6 IS BOLTED TO THE STRIPPER AND THE SUPPORT BLOCK REMOVE BRIDGE PLATE, (1.00 inch THICK) THIS WILL ALLOW A SMALLER SHUT HEIGHT. S.H.C.S. TO HOLD CAM TO DIE. UPPER DIE HEEL BLOCK CAM CAM DIE STRIPPER BOTTOM DIE BOLT MACHINED POCKETS FOR CAM CLEARANCE SUPPORT BLOCK D
14 FIGURE #3 HEEL BLOCKS FOR LOW PROFILE TOOLS FRONT HEEL BLOCK BACK HEEL BLOCK.125 RAD (2PLS) DRILL TAP (3 PLS) DRILL C-BORE FOR SHCS (3 PLS) DRILL TAP 6-32 (3PLS).25 RAD (2PLS) 45 X.02 (4PLS) CLEARANCE POCKETS FOR CAM FRONT HEEL BLOCK BACK HEEL BLOCK DRILL C-BORE FOR 6-32 SHCS (3PLS) CAM TRACK CAM FOLLOWER X.02 (4PLS) PARALLEL SHIMS FOR CLEARANCE ON SET UP D
15 FIGURE #4 POSITION FOR CAM FOLLOWERS (RIGHT-HAND THREADING ONLY) POSITON A POLYGON DRIVE SHAFT. D
16 FIGURE #5 LP25M6 & LP516M8 CAM DRIVER MOUNTING INFORMATION DRILL AND C-BORE FOR 1/2-13 SHCS (4PLS).500 DOWEL PIN (2PLS) CAUTION BOLTS AND DOWEL PINS CAN`T MOUNT BELOW THIS SURFACE. D
17 FIGURE #6 LOW PROFILE TOOLS MOUNTED ON A STRIPPER PLATE BRIDGE STRIPPER HEEL BLOCK HEEL BLOCK BOSS TIP OF TAP SHOULD NOT EXTEND BELOW BOSS. BOSS SHOULD NOT EXTEND BELOW STRIPPER PLATE. D
18 FIGURE #7 RECOMMENDED LUBRICATION SYSTEM OPTION #1 STRIPPER PLATE NOZZLE SHOULD BE WITHIN.02 TO.100 OF THE DIA OF TAP. MACHINE SLOT OR DRILL POCKET FOR TUBE. SLOT IS PROVIDED IN PITCH INSERT TO ALLOW 3/32 BRASS TUBING TO PASS THRU. 3/32 OD X.06 ID BRASS TUBING.093 ID X 1/8 OD TEFZEL TUBING USE TUBING THAT WILL WITHSTAND 1,1,1 TRICHLORETHANE. THIS COMPOUND IS USED IN GOOD TAPPING FLUIDS. D
19 FIGURE #8 RECOMMENDED LUBRICATION SYSTEM OPTION #2 STRIPPER PLATE NOZZLE SHOULD BE WITHIN.02 TO.100 OF THE DIA OF TAP. 3/32 OD X.06 ID BRASS TUBING MACHINE SLOT OR DRILL POCKET FOR TUBE. SLOT IS PROVIDED IN PITCH INSERT TO ALLOW 3/32 BRASS TUBING TO PASS THRU. 1/8 OD X.097 ID BRASS TUBING EITHER USE SOLDER OR E-POXY (JB WELD) IF TUBE NEEDS TO BE BENT, USE A TUBE BENDER COMPRESSION FITTING FOR 1/8 DIA TUBE 1/8 MALE PIPE THREAD IS 5090K11 1/8 FEMALE PIPE THREAD IS 5089K11 D
20 FIGURE #9 PITCH INSERT ASSEMBLY BOSS OR STRIPPER COLLET TAP FEMALE LEAD SCREW MALE LEAD SCREW KEY STOCK MIS-FEED SPRING D
21 FIGURE #10 SHUT HEIGHT OF CLEARANCE AT THE END OF THE STROKE MIMIMUM SHUT HEIGHT CLEARANCE HOLES WILL BE REQUIRED IN DIE SHOE FOR CAM SIDE PLATES. D
22 FIGURE #11 FIXED CAM DIMENSIONS FOR THE LP CAM DRIVER (RAPID TAP SOFTWARE WILL SELECT EITHER CAM A OR CAM B).005 ABC C B ENGRAVE JOB NUMBER PLS A.375 2PLS CAM A /8 PRESS FIT DOWEL PIN 4 PLS TAP AND C-BORE FOR 5/16-18 X 1.00 S.H.C.S 4 PLS PLS PLS CAM B /8 PRESS FIT DOWEL PIN 4 PLS TAP AND C-BORE FOR 5/16-18 X 1.00 S.H.C.S 4 PLS CAM TRACK HEIGHT CAM TRACK HEIGHT.50 OF STRAIGHT.50 OF STRAIGHT CAUTION BOLTS CAN`T MOUNT BELOW THIS SURFACE MINIMUM DIM BREAK ALL SHARP EDGES FINISH: NONE MATERIAL: 7075-T6 ALUMINUM MATERIAL CAM BE REMOVED TO ADD CLEARANCE..500 MIN DIM FROM END OF CAM TRACK TO EDGE OF MATERIAL. D
23 FIGURE #12 LOW PROFILE TOOLS MOUNTED ON A SPRING STRIPPER SPRING TRAVEL IS BASED ON TAPPING STROKE, PLUS.25 OF PRELOAD. 4 NITROGEN SPRINGS EQUALLING 3000 LB BEFORE CAMS MAKE CONTACT WITH CAM FOLLOWERS..500 DIA LOCATING PINS (4PLS) THIS WILL KEEP THE STRIPPER PLATE FROM SHIFTING WHEN THE CAMS MAKE CONTACT WITH THE CAM FOLLOWERS. D
24 FIGURE #13 TAPPED HOLE DETECTION (TO DETERMINE WHETHER THE TAP FULLY PENETRATES THROUGHT THE MATERIAL) MATERIAL GUIDES DIE SPRING DIE PLATE SPRING SET SCREW WITH THRU HOLE SWITCH SPRING LOADED BRIDGE STRIPPER MATERIAL STRIP GUIDE PINS CLEARANCE BETWEEN MATERIAL AND PLUNGER IS 2.5 X PITCH D
25 FIGURE #14 EXAMPLE OF 13 LP TAPPING UNITS TAPPING FROM THE BOTTOM UP D
26 FIGURE #15 EXAMPLE OF LP25M6 TAPPING UP AND DOWN IN THE SAME STATION D
27 FIGURE #16 CAM DRIVER TEMPLATE FOR ME1024 CAM TEMPLATE FOR ME OIL HOLE.375 RAD (4 PLS) (2 PLS).250 (2 PLS) GREASE FITTING (45 DEG ANGLE) (2 PLS) DIA NOTE: MIN SHADED AREA TO BE MACHINED BY CUSTOMER BASED ON APPLICATION 1 CAM PROFILE DETERMINED BY PRESS STROKE AND TAPPING STROKE MODEL ME STANDARD CAM OPEN AND SHUT HIEGHTS D
28 FIGURE #17 ME1024 CAM FIXED DIMENSIONS ENGRAVE JOB NUMBER RAD (2 pls).375 RAD (4 PLS) R (4pls) (2 pls).250 (2 pls) (2 pls) DIA FINISH: NONE MATERIAL: 7075-T6 ALUMINIUM D
29 FIGURE #18 ME1024 CAM ON BRIDGE STRIPPER.630 CLEARANCE HOLE FOR DRIVE SCREW MATERIAL GUIDES DIE SPRING DIE PLATE SPRING LOADED BRIDGE STRIPPER MATERIAL STRIP GUIDE PINS D
30 FIGURE #19 CAM DRIVER MOUNTING FOR ME1024 CAM USING A SPRING STRIPPER THIS SECTION IS REMOVED BY END USER BASED ON PROPER HEIGHT REQUIREMENTS THIS DIM. IS THE SAME FOR ALL CAM`S, WHEN USED IN A SPRING STRIPPER APPLICATION. SUBTRACT AMOUNT OF PRELOAD TRAVEL USED BEFORE TAPPING FROM THIS 1.00 DIM. IN MOST CASES USE.05 TO.100 OF PRELOAD TRAVEL. THIS WILL INSURE PROPER STRIPPING FOR TAPPING. SPRING TRAVEL IS BASE ON TAPPING STROKE, PLUS PRELOAD ON MATERIAL BEFORE TAPPING. MATERIAL DIE MICRO SWITCH CAUTION IF USING A SPRING STRIPPER. THERE SHOULD BE A SENSOR TO MAKE CERTAIN THAT THE STRIPPER COMES DOWN 100%. IF STRIPPER DOES NOT COME DOWN ALL THE WAY THE UNIT COULD BOTTOM OUT, CAUSING THE CAM ROLLER TO BREAK. D
31 FIGURE #20 MOUNTING THE ME1024 UNIT IN A HYDRAULIC PRESS OPEN.625 DIA X 1.35 DEEP RELIEF HOLE IN PUSH BLOCK FOR SCREW MINIMUM THIS KEEPS PUSHER BLOCK FROM MAKING CONTACT ON CAM PLATES. CAM PLATE CLOSED D
32 FIGURE #21 TAPPING WITH MATERIAL LIFTERS STOP BLOCK TO OVER COME NITROGEN SPRINGS SPRING BRIDGE STRIPPER.50 DIA SPRINGS MATERIAL TRAVEL NITROGEN SPRINGS MATERIAL LIFTERS SUPPORT PAD APPROXIMATELY 1800 LB OF NITROGEN PRESSURE. D
33 FIGURE #22 SAMPLE LAYOUT FOR MULTIPLE TAPPING WITH 3 ME1024 UNITS IN ONE DIE ME1024 TAPPING UNITS AIR CLAMP AIR FEEDER NOTE: ALL DIMENSIONS ARE APPROXIMATE D
34 FIGURE #23 TYPICAL WAY OF APPLYING TAPPING UNITS TO IN-DIE TAPPING MOUNTING SCREWS FOR CAM FIRST HOLE TAPPED PART PUNCHED OUT PUNCH HOLES FOR TAPPING SECOND HOLE TAPPED THIRD HOLE TAPPED THIS DIE HAS ONE MACHINED POCKET FOR ALL TAPPING UNITS TAPPING UNITS 1,2,3 3/8-16 S.H.C.S PART THREE HOLES TAPPED MACHINED POCKET THIS DIM. IS FROM THE TOP OF THE MATERIAL OR EXTRUSION TO THE TOP OF THE CAM IN THE CLOSED POSITION 2.00 DIE MATERIAL 3.00 BOTTOM DIE SET 5.00 PARALLEL 1.00 D
35 FIGURE #24 SUB-PLATE FOR LP25M6 GUIDE RAIL 1/4-20 1/2-20 GUIDE RAIL STOP BLOCK SUB-PLATE D
36 FIGURE #25 SUB-PLATE FOR LP25M6 CAM SUB-PLATE 5/16-18 S.H.C.S. RAIL STOP BLOCK D
37 FIGURE #26 SUGGESTED LAYOUT FOR TAPPING BOTTOM UP WITH LOW PROFILE TOOLS AND USING A SUB DIE DIE IN OPEN POSITION DIE IN CLOSED POSITION D
38 FIGURE #27 LP25M6 MOUNTED ON A SPRING STRIPPER MATERIAL LIFTER STOP BLOCKS OR NITROGEN SPRINGS TO OVER RIDE 3,000 LBS OF SPRING PRESSURE. FORMING TRAVEL APPROXIMATIELY 3,000 LBS OF SPRING PRESSURE. D
39 Designing a Cam Driver (Models ME1024 and LP25M6 only) 1. TOOL MODEL: ME1024 LP25M6 2. STROKE OF PRESS: 3. TAPPING STROKE: The remaining stroke left after the material has advanced in its progression. Example: If a 6" stroke press requires 2" to advance or progress, the tapping stroke would be (6" - 2") = 4". 4. SPEED OF PRESS IN STROKES PER MINUTE: 5. TOTAL THICKNESS OF MATERIAL (include extrusion if applicable): Material thickness must include the gap between the tip of the tap and the top of material or extrusion. (Failure to do so could cause improper tap penetration.) (See Figure #15.) 6. MATERIAL TYPE: 7. TAP SIZE: 38
40 Rapid T.A.P. Software Rapid T.A.P. Software (Tapping Application Program) Software that aids in the development of dies with Danly IEM in-die-tapping tools. This software is designed to educate die designers and stamping facilities on the benefits of In-die Tapping (IDT) and provide easy ways to design dies that incorporate the IDT tools. Rapid TAP replaces Campro, an earlier DOS based computer program. Rapid TAP produces needed CAD information for the IDT Cam Drivers that are proprietary to Danly IEM tapping tools. Rapid TAP s program logic evaluates the sinusoidal acceleration that is inherent with mechanical presses and converts it into a linear tapping motion. This conversion is more accurate than altering gear ratios 39
41 Trouble Shooting 1. DISTORTED THREADS Threads are distorted and the go-gage will not go into the tapped hole. Check to see if any portion of the die is hitting the top of the threads, such as the stripper plate, form block or a hold-down form pad. If this is the case, provide clearance for the hole by grinding or machining a counter bore. 2. TAP BREAKS ON EVERY HIT Make sure the hole is the correct size for a metal forming tap. If you are using a hole size recommended for a cutting tap, it is too small and will result in tap breakage. Ensure that the hole is being registered properly beneath the tap. See Mounting Procedures in the installation manuals. For recommended pre-hole sizes, refer to the tables on pages 9 and 10 of this manual. 3. TAP BREAKS AFTER ONE TO FIVE HITS Tap height may be misadjusted and stocking out below the nose piece or boss. This condition often results in the tap catching on the material as at advances. 4. TAP BREAKS PREMATURELY Check the lubrication. A discolored or black tap indicates that an improper level nor type of lubrication is being applied. 5. TAP SPINS BUT DOES NOT PENETRATE THE HOLE The tap is backed up by a spring for no hole conditions. If this spring is weak there may not be enough pressure to get the tap started. If a spring stripper or a spring loaded bridge stripper is used, adjust the tap so that is protrudes slightly from the nose piece. This will put a preload on the spring and increase spring pressure. If this does not correct the condition, a stronger spring will have to be used. Call the factory for assistance if this is the case. 6. IF CHIPS ARE DEVELOPING The pre-hole for the tap is too small. Opening up the hole by.002" to.003" will usually fix the problem. Use 65% of thread to start with. 40
Why Use. Stock Ejectors. The New Industry Standard
Why Use s The New Industry Standard This product may be covered by one or more patents or patent applications. See http://www.standardlifters.com/patents.html for details. 8/14 - Rev. 1 Application - Ejecting
More informationTOOL DESIGN - MANUFACTURING DESIGN SPECIFICATIONS FOR TOOLING AND EQUIPMENT SECTION H - DIE DESIGN TABLE OF CONTENTS. H.1 General...
TABLE OF CONTENTS H.1 General...Page 2 H.2 General Die Layout...Page 2 H.3 General Die Features...Page 2 H.4 Specific Die Type Features...Page 5 H.5 Special Punches and Die Bushings...Page 6 H.6 Wire E.D.M...Page
More informationEngineering Data Stock Ejectors
Engineering Data s The New Industry Standard This product may be covered by one or more patents or patent applications. See http://www.standardlifters.com/patents.html for details. 8/14 - Rev. 1 Things
More informationTu r n y o u r p r e s s b r a k e o r p u n c h p r e s s i n t o a h o l e p u n c h i n g p r o f i t c e n t e r.
Tu r n y o u r p r e s s b r a k e o r p u n c h p r e s s i n t o a h o l e p u n c h i n g p r o f i t c e n t e r. U n i P u n c h M o d u l a r To o l i n g Works with existing presses Multiple holes
More informationMSR/MSB Mechanical Setting Tool
Tech Unit No: 0620000004 Revision: B Approved By: Quality Engineer Date: 2014-12-16 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical
More informationWhy Use. Pilot Assemblies. The New Industry Standard
Why Use Pilot Assemblies The New Industry Standard This product may be covered by one or more patents or patent applications. See http://www.standardlifters.com/patents.html for details. 01/17 - Rev. 11
More informationBHJ Products, Inc. Parts List & Instructions
Product Name: Lifter-Tru Kit for Ford Windsor & SVO Small Block V8 Page 1 of 5 Kit Contents: 2x End Plates 2x 5/8 Threaded Adjustment Sleeves 1x Front Angle Bracket 2x 5/8 Adjustment Sleeve Spacers * 1x
More informationDanly Die Sets CATALOG DIE SETS. Quality & performance Quick delivery Precision Components
Danly Sets TM CATALOG DIE SETS Quality & performance Quick delivery Precision Components 1 TM Danly Sets www.anchordanly.com CATALOG DIE SETS Service We Deliver and Quality You Can Depend On Danly Sets
More informationWORKHOLDING MADE IN EUROPE MANUAL LATHE CHUCKS, CENTERS, ROTATING BODIES OIL COUNTRY CHUCKS, POWER CHUCKS, VTL CHUCKS, ROTARY TABLE PACKAGES
EUROPEAN PRECISION & QUALITY WORKHOLDING MADE IN EUROPE MANUAL LATHE CHUCKS, CENTERS, ROTATING BODIES OIL COUNTRY CHUCKS, POWER CHUCKS, VTL CHUCKS, ROTARY TABLE PACKAGES EUROPEAN PRECISION & QUALITY With
More informationDoler Self Colleting Machines*
* P2 Drill with Variable Spacing Foot Light and compact - yet rigid and rugged Modular design - for easy setup and servicing Variety of spindle speeds and terminations to satisfy a wide range of applications
More informationTorque Specs - Main Caps 1-5 1/2" bolts 100 ft lbs W / CMD# /2" splayed 100 ft lbs Dart s inner head studs 3/8" 7/16" stepped 50 ft lbs
DART MARK IV Iron Big Block - Technical Notes Deck Height... 9.800" & 10.200" Bore... 4.250", 4.500", 4.560" and 4.600" unfinished Main Bearing Size... Standard BBC Main Caps... All 4 bolt - Steel or Ductile
More informationMSR/MSB Mechanical Setting Tool
Tech Unit No: 0620000004 Revision: C Approved By: Quality Engineer Date: 201-1-9 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical
More informationBHJ Products, Inc. Parts List & Instructions
Product Name: Lifter-Tru Kit for General Motors LS V8 Page 1 of 5 Kit Contents: 2x End Plates 2x Threaded Adjustment Sleeves 1x Front Angle Bracket 2x M10-1.5 x 65 Hex Head Bolts * 2x Angle Adapter Blocks
More informationProfiting with Wire EDM
3 Profiting with Wire EDM Users of Wire EDM 55 Parts made with the wire EDM process are used for machining conductive materials for medicine, chemical, electronics, oil and gas, die and mold, fabrication,
More informationHigh Precision Air Chucks
Precision Workholding Solutions High Precision Air Chucks www..com Improve productivity and lower the cost of secondary machining operations..... through high concentricity. Holding close concentricity
More informationACCU-BEND TM. Holds ± 1/2 angle tolerance. Designed for consistent production of angles Able to overbend up to 120
TRUSTED SOLUTIONS AND INNOVATION ACCU-BEND TM Holds ± 1/2 angle tolerance Designed for consistent production of angles Able to overbend up to 120 Decreases forming tonnage by 40% 80% ACCU-BEND TM Strategically
More informationCrankshaft Gear Modification and Assembly Procedures
652 Oliver Street Williamsport, PA 17701 U.S.A. Tel. 570-323-6181 Fax. 570-327-7101 www.lycoming.textron.com MANDATORY SERVICE BULLETIN DATE: January 30, 2003 Service Bulletin No. 475C (Supersedes Service
More informationOperating, Servicing, and Safety Manual Model # 100 Standard Hydraulic Tubing Notcher Model #100-U Heavy Duty Hydraulic Tubing Notcher
Operating, Servicing, and Safety Manual Model # 100 Standard Hydraulic Tubing Notcher Model #100-U Heavy Duty Hydraulic Tubing Notcher Model # 100 Standard Model #100-U Heavy Duty CAUTION: Read and Understand
More informationPrecision Chucks for Improved Accuracy and Increased Productivity
Precision Workholding Technology Precision Chucks for Improved Accuracy and Increased Productivity Precision Air Chucks (Self Contained Design) MicroCentric Precision Air Chucks feature a patented open
More informationTorque Specs - Main Caps 1-5 1/2" bolts 100 ft lbs W / CMD# /2" splayed 100 ft lbs Dart s inner head studs 3/8" 7/16" stepped 50 ft lbs
DART GEN V Iron Big Block - Technical Notes Deck Height... 9.800" & 10.200" Bore... 4.250" Option (4.500, 4.560 and 4.600) unfinished Main Bearing Size... Standard BBC Main Caps... All 4 bolt - Steel or
More informationENGINEERING STANDARDS SECTION: D TOG-L-LOC V-LOC OVAL-LOC LANCE-N-LOC INFORMATION. Tog-L-Loc. How The Joining Process Works
Tog-L-Loc Tog-L-Loc is a circular, leakproof joint formed by drawing the metals into a circular "cup'' and then expanding the diameter to form a 360 radial lock below the bottom sheet. How The Joining
More informationEngineering Data Pilot Assemblies
Engineering Data Pilot Assemblies The New Industry Standard This product may be covered by one or more patents or patent applications. See http://www.standardlifters.com/patents.html for details. 01/17
More informationPage 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16
R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LACPACC-002 LACPACC-003 LACP-16TxxLP5 (0.5-in lead screw pitch) LACP-16TxxL1 (1-in lead screw pitch) C P I R K 4 ea Flanged
More informationTable of Contents. B. Base Tool Changer...2 MC-6 Manual Tool Changer...2
Table of Contents B. Base Tool Changer...2 MC-6 Manual Tool Changer...2 1. Product Overview... 2 1.1 Master Plate Assembly... 2 1.2 Tool Plate Assembly... 3 1.3 Optional Modules... 3 2. Installation...
More informationACCESSORIES CATALOG BORING AND FACING HEADS LIVE CENTERS
ACCESSORIES CATALOG BORING AND FACING HEADS LIVE CENTERS SKODA LIVE CENTERS SKODA & STM HEAVY DUTY LIVE CENTERS - CSN 243324 Features The rotating spindle is extended right through the tapered shank Two
More informationUser's Guide for Tooling
BTM's Tog-L-Loc and Lance-N-Loc Cross Section of a Lance-N-Loc Tog-L-Loc & Lance-N-Loc are protected by patents in the U.S.A. and most other industrialized nations. Tog-L-Loc & Lance-N-Loc are registered
More informationInTurn Ultra and Ultra-T Indexing and Turning 4 th axis
Specifications for the InTurn Ultra and Ultra-T Indexing and Turning 4 th axis Industrial quality. 100% duty cycle. Production ready. The InTurn series is the only CNC mill accessory that provides both
More informationComplete O.D. Machining in One Operation
MFDODM209 Complete O.D. Machining in One Operation Including: Hydra-Drive For Extreme Accuracy CREATING INNOVATIONS IN FACE DRIVING TECHNOLOGY www.facedrivers.com Complete O.D. Machining in one Operation
More informationw w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models
-J067 REV. 008-07- GENERAL Kit Number 8-08 Models TIMKEN BEARING CONVERSION TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationCNC EXPANDING MANDRELS
CNC EXPANDING MANDRELS ID CLAMPING OFFERS FULL OD PART ACCESS PARALLEL EXPANSION FOR OPTIMUM ACCURACY AND GRIP FORCE LARGE RANGE IN STOCK FOR IMMEDIATE SHIPMENT ROYAL CNC EXPANDING MANDRELS Rigid and Accurate
More informationRound Die Products. Check our website for the latest technical information.
Round Die Products www.daytonlamina.com Check our website for the latest technical information. 1 BUSHINGS General Information Bushings... 2 & 3 STANDARD SHOULDER BUSHINGS Bronze Plated & Solid Steel...
More informationLEADING SOLUTIONS IN THREAD MILLING TECHNOLOGY
LEADING SOLUTIONS IN THREAD MILLING TECHNOLOGY Thread with Maximum Confidence, Depth, Versatility and Economy. Emuge Shur-Thread TM, Threads-All TM, Vario-Z and NPT Solid Carbide Thread Mills; and Gigant-ic
More information1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward.
Figure 1 Miniature Quick Change Applicators, of the end feed type, are designed to crimp end feed strip terminals to prestripped wires. Each applicator is set up to accept the strip form of certain specific
More informationHeavy Equipment Solutions
Heavy Equipment Solutions Because ensuring a leak-free solution is critical. It has to be Hydratight. For more than 100 years, Hydratight has provided world-class bolted joint solutions, assessing and
More informationSTRENGTH Aligned teeth provide superior gripping power over standard vertical teeth. STRENGTH Diamond serrated jaws provide a firm grip
STRENGTH Aligned teeth provide superior gripping power over standard vertical teeth STRENGTH Diamond serrated jaws provide a firm grip PLIERS AND SNIPS Locking Pliers Slip Joint Pliers Electrician s Pliers
More informationCoroChuck 970 SynchroFlex Benefits
Benefits Better surface quality on the flanks of the cut threads Longer tool life due to less friction Greater process security Due to the reduced risk of breaking the tap especially with small dimensions
More informationHolemaking Products & Accessories
Holemaking Products & Made of top-of-the-line materials for longer lasting performance, Klein's diverse line of drill bits and holemaking products and accessories provide accuracy and consistency to get
More informationTOOLS AND INSTALLATION
TOOLS AND INSTALLATION Safe, leak-free operation of any high-pressure system is dependent on correctly prepared and installed connections. This section outlines proper instructions for the machining and
More informationA BALAX, INC. GUIDE TO TAPPING IN THE 21ST CENTURY
2011 Threading Solutions for Every Industry A BALAX, INC. GUIDE TO TAPPING IN THE 21ST CENTURY At Balax, we recognize the increased demands placed on our customers for improved quality and lower production
More informationACCESSORIES CATALOG. SKODA LIVE CENTERS BORING AND FACING HEADS
ACCESSORIES CATALOG BORING AND FACING HEADS SKODA LIVE CENTERS www.sowatool.com SKODA LIVE CENTERS Skoda Heavy Duty Live Centers - CSN 4334/CSN 4334M Features The rotating spindle is extended right through
More informationLCSF Low Clearance Split Frame
Designed For Portability And Limited Clearance Full Range 2in - 48in for Pipe and Tube Optional Bridge Slide for Heavy Wall Pipe EXTERNALLY MOUNTED PORTABLE PIPE CUTTING AND BEVELING SYSTEM E.H. Wachs
More informationLORON SERVICE MANUAL / PARTS LIST SINGLE DOUBLE PALLET HANDLER CONTENTS: PAGE 1 Lift Truck Requirements General Installation Procedures
LORON SERVICE MANUAL / PARTS LIST SINGLE DOUBLE PALLET HANDLER CONTENTS: PAGE 1 Lift Truck Requirements General Installation Procedures 2 Mounting Options Stop Block Adjustments 3 General Weekly Inspection
More informationw w w. h d o n l i n e s h o p. d e AUTOMATIC COMPRESSION RELEASE TOOL GENERAL INSTALLATION -J04654 REV Kit Number Models
-J05 REV. 008-0- GENERAL Kit Number 98-08 Models AUTOMATIC COMPRESSION RELEASE TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationLathe. A Lathe. Photo by Curt Newton
Lathe Photo by Curt Newton A Lathe Labeled Photograph Description Choosing a Cutting Tool Installing a Cutting Tool Positioning the Tool Feed, Speed, and Depth of Cut Turning Facing Parting Drilling Boring
More informationA SRF/SERF A SRF/SERF
A1100-055SRF/SERF A1100-056SRF/SERF Remote Fill Assembly INSTALLATION INSTRUCTIONS **CRITICAL - MUST READ** This unit can only be used for new installations or tank level retrofits that allow access to
More informationEngineering Data Rail Lifters
Engineering Data Rail Lifters Bolt On Ready Stock Rails This product may be covered by one or more patents or patent applications. See http://www.standardlifters.com/patents.html for details. 12/13 - Rev.
More informationCOLLET CLOSERS, FIXTURES AND COLLETS FOR ROTATING AND FIXED APPLICATIONS
COLLET CLOSERS, FIXTURES AND COLLETS FOR ROTATING AND FIXED APPLICATIONS ROYAL QUICK-GRIP MANUAL COLLET FIXTURES FOR 4TH AND 5TH AXIS APPLICATIONS q Unit is actuated via a hybrid mechanical/hydraulic mechanism.
More informationMACHINE TOOL ACCESSORIES
VERTICAL 5-C COLLET VISE SERIES 344: VERTICAL 3-C COLLET VISE SERIES 344: : 2-1/2 x 7-3/4 Height: 4 Small movement of lever opens or closes collet. 2030000 CAM OPERATED 5-C HORIZONTAL/VERTICAL COLLET FIXTURE
More informationPrecision made in Germany. As per DIN The heart of a system, versatile and expandable.
1 Precision made in Germany. As per DIN 8606. The heart of a system, versatile and expandable. Main switch with auto-start protection and emergency off. Precision lathe chuck as per DIN 6386 (Ø 100mm).
More informationINSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET
HIGH EDGE 2 1/4"(57mm) 03079400070 INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1³ ₄" (45mm)
More informationMINI-LATHE QUICK CHANGE TOOL POST
MINI-LATHE QUICK CHANGE TOOL POST Cutting and assembly details Machinists should familiarize themselves with the contents of this section before jumping in to the drawings. Many details are described here
More informationMXE32P Profiled Rail Bearing Screw-Drive Actuators 32mm (1-1/4 inch) Series
S Parts Sheet MXEP Profiled Rail Bearing ScrewDrive Actuators mm (/ inch) Series Models: MXEP MXEP MXEP MXEPSN0 MXEPSN0 7b 800007_0_MXE 8 8 9 7a 7 0 9 8 9 7 0 Parts Listing A/R= As Required 0 MXES ITEM
More informationOPERATOR S MANUAL Euromac Punch Press Applications
ROLLER SOLUTIONS Use and Maintenance Instructions OPERATOR S MANUAL Euromac Punch Press Applications ROLLING SHEAR ROLLING RIB ROLLING OFFSET ROLLING PINCHER INDEX I. SAFETY WARNING 2 II. BASIC TOOLING
More informationHARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet
HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet Read the enclosed instructions and recommendations before any installations CONTENTS Dead-Length Collet Adaptation
More informationHigh-precision inch guide units Made in Germany
High-precision inch guide units Made in Germany cm 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 cm inch inch 1 2 3 4 5 6 7 8 STEINEL All you need for tools Your partner for punching and bending
More informationRotary Engraving Fact Sheet
Rotary Engraving Fact Sheet Description Rotary engraving is the term used to describe engraving done with a rotating cutting tool in a motorized spindle. The tool, or cutter, cuts into the surface of the
More informationMetals can be bought from suppliers in standardized forms and sizes, such as round,
1.4 METAL CUTTING BAND SAWS: Metals can be bought from suppliers in standardized forms and sizes, such as round, rectangular or square bar stock or in the form of large sheets (plates). Bar stock normally
More informationTAPPING CHUCKS & COLLETS
TAPPING CHUCKS & COLLETS CAT er Tension/Compression Holders 86 CAT er Rigid Holders 86 BT er Tension/Compression Holders 87 BT er Rigid Holders 87 HSK Tension/Compression & Rigid Holders 88 NMTB er Tension/Compression
More informationRight Angle Tools Accessories
Accessories for the No. 15 and 140 Series Right Angle Drills Bushing S125 Series S300 Series Thread Dim A Part No. Dim. A Part No..75-16 L.H. 5.3125 in. (135mm) 5.4375 in. (138mm) 5.4375 in. (138mm) 619143
More informationASSIGNMENT 4. Textbook Assignment: The point, edge, face, heel, and tang are the five parts of which of the following tools?
ASSIGNMENT 4 Textbook Assignment: "Files," "Grinders and Sharpening Stones," "Scrapers," "Awls," "Bolt and Cable Cutters," "Glass Cutters," "Knives,' 'Pipe Cutting and Threading Tools," "Tube Cutting and
More informationSTAR TOOL SUPPLY / GRAND TOOL SUPPLY
Made of hardened and tempered tool steel with ground points. es have knurled grip. Set consists of 1 each of 5 punches in plastic pouch. Point Size Length 1/16 3 3040004 5/64 4 3040005 3/32 4 3040006 9/64
More informationStripping & Blanking Supplies
Stripping & Blanking Supplies Stripping Pins Stripping Pins - available in the sizes and styles shown above. 50 mm tall (2 ). All base sizes are the same (4mm) for consistent drilling and laser cutting
More informationModel 204B-EM Elbow Mandrels Rev TABLE OF CONTENTS
92-0697 Rev. 970131 Model 204B-EM Elbow Mandrels TABLE OF CONTENTS CUSTOMER MESSAGE Inside Front Cover SAFETY PRECAUTIONS 3 GENERAL DESCRIPTION 6 MAINTENANCE 7 OPERATION 8 TROUBLE SHOOTING 11 ACCESSORIES
More informationHBS-AP ASSEMBLING INSTRUCTIONS
ALUMINIUM PIPEWORK - ALUMINIUM PIPEWORK - ALUMINIUM PIPEWORK 97 HBS-AP ASSEMBLING INSTRUCTIONS 1. INTRODUCTION 1.1. This manual is very easy to consult and we recommend reading it before starting work,
More informationENGINEERING STANDARDS SECTION: TOG-L-LOC V-LOC LANCE-N-LOC INFORMATION. Tog-L-Loc. How The Joining Process Works
Tog-L-Loc Tog-L-Loc is a circular, leakproof joint formed by drawing the metals into a circular "cup'' and then expanding the diameter to form a 360 radial lock below the bottom sheet. How The Joining
More informationNORTH AMERICA ONLY PIPE SLUG CHUTE DETAILS ALL DIMENSIONS IN INCHES
"B" B. C. PIPE SLUG CHUTE DETAILS ALL DIMENSIONS IN INCHES PVC - DWV PIPE FITTINGS FOR "X" SOC. HD. SCREW (N) HOLES "D" "C" "A" O.D. ALTER IF CONSTRAINED BY SPACE LIMITATION. (2) MIN. FASTENING HOLES REQUIRED.
More informationFLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.
More informationOperator's manual. TruTool TKF 1500 (1A1), (1B1)
Operator's manual TruTool TKF 1500 (1A1), (1B1) Table of contents 1 Safety 4 1.1 General safety information 4 1.2 Specific safety information for beveler 4 2 Description 6 2.1 Intended use 6 2.2 Technical
More informationIntroduction to Machining: Lathe Operation
Introduction to Machining: Lathe Operation Lathe Operation Lathe The purpose of a lathe is to rotate a part against a tool whose position it controls. It is useful for fabricating parts and/or features
More informationDC3210. Recommended Closer Size
Installation Instructions For Non-Hold Open or A Hold Open Arm Option DC3200 Series Multi-Sized thru 6 Regular Arm Universal Door Closers Parallel Arm Jamb Mount See pages 2&3 See pages 4&5 See pages 6&7
More informationWhy Use Guided Keepers
Why Use Guided Keepers Guidance and Retention - ALL-IN-ONE This product may be covered by one or more patents or patent applications. See http://www.standardlifters.com/patents.html for details. 12/13
More informationClayton Off Road COR COR COR
Clayton Off Road COR-4806011 COR-4806021 COR-4806031 JEEP GRAND CHEROKEE WJ LONG ARM UPGRADE KITS (1999-2004 WJ) NOTES: This product requires general welding, fabrication and automotive mechanic skills.
More informationPRODUCTION VISES. Vises. Bock Quick Change Fixturing. 5-Axis Production Vises
Vises Introduction to Design... 74 75 VMC/HMC Solutions...76 77 Ball Lock Mounting System...78 79 Production Vises 4" (100 mm) Production Vises... 80 81 6" (150 mm) Production Vises...82 83 Self Centering
More informationDrawbars for Milling Machines
Machine Tool & Drawbars for Milling Machines Made in USA Drawbars from low carbon steel, soft and black oxide plated. Drawbars are manufactured from two parts the shaft and the hex. Drawbars for Milling
More informationHead Serial Number : Date Purchased : Where Installed: (make/model of machine) DB75 & DB75V OPERATION AND MAINTENANCE MANUAL
DELUXE STITCHER C O M P A N Y I N C. Head Serial Number : Date Purchased : Where Installed: (make/model of machine) DB75 & DB75V OPERATION AND MAINTENANCE MANUAL DB75HD231/2...Muller-Martini Head...23
More informationEUROPE ONLY NUMERICAL INDEX DESIGN REQUIREMENTS FOR OBI DIES AND OBI BLANK DIES
NUMERICAL INDEX UNIT PAGE ITEM SUBJECT 42M 5 1 GENERAL INFORMATION 5 1.1 START OF DESIGN 5 1.2 CONSTRUCTION OF DIES 5 1.3 DIE FIXING 5 1.4 SHUT HEIGHT 6 1.5 MATERIAL 6 1.6 GUIDING UPPER-LOWER DIE 6 1.7
More informationOperation and Service Instructions With Replacement Parts List
No. 700-F TUBE BENDER Operation and Service Instructions With Replacement Parts List Warning! Keep body parts away from pinch/bend areas while using. Ensure tubing is secure in tool before bending. Always
More informationThe Catalogue of Nomura Tool Works Co., Ltd. Tool manufacturing since 1954 Bent Shank Taps Nib Taps Nut Taps
The Catalogue of Nomura Tool Works Co., Ltd. Tool manufacturing since 1954 Bent Shank Taps Nib Taps Nut Taps Introduction In today's highly developed machine industry, a tap is a cutting tool that requires
More informationProduct Information Report Maximizing Drill Bit Performance
Overview Drills perform three functions when making a hole: Forming the chip The drill point digs into the material and pushes up a piece of it. Cutting the chip The cutting lips take the formed chip away
More informationScrews. Introduction. 1. Nuts, bolts and screws used to clamp things together. Screws are used for two purposes:
Screws Introduction Screws are used for two purposes: 1. To clamp things together. 2. To control motion. 1. Nuts, bolts and screws used to clamp things together. Nuts, bolts and screws that are used for
More informationCNC Chucker Lathe P/N 6600, 6610, and 6620
WEAR YOUR SAFETY GLASSES FORESIGHT IS BETTER THAN NO SIGHT READ INSTRUCTIONS BEFORE OPERATING PRODUCT DESCRIPTION 6600 CNC Chucker w/3c headstock, ball screws, high-torque stepper motors & PC w/4-axis
More informationLate Spiders - Forming Bubble Flares on Brake Lines
Late Spiders - Forming Bubble Flares on Brake Lines Brake lines on 30 year old cars often require replacement. In addition to the inevitable corrosion, the connections are damaged during multiple replacements
More informationSHEREX FASTENING SOLUTIONS PNEUMATIC SPIN-SPIN INLINE STYLE RIVET NUT INSTALLATION TOOL SSG-902 MANUAL
SHEREX FASTENING SOLUTIONS PNEUMATIC SPIN-SPIN INLINE STYLE RIVET NUT INSTALLATION TOOL SSG-902 MANUAL SSG-902 Specifications R.P.M. - 1500 *Air Pressure - 60-90 psi (oiled) Weight - 2 lbs. (0.9 kg) Air
More informationPREMIUM THIN TURRET TOOLING SYSTEM
Distribuitor: S.C. SM TECH S.R.L. www.smtech.ro www.wilsontool.ro office @ smtech.ro Tel: 0374991480 Tel mob: 0745528494 Fax: 0374091010 PREMIUM THIN TURRET TOOLING SYSTEM Strength. Performance. Innovation.
More information45PC. TAP AND DIE SET
Model # 7560 7561 45PC. TAP AND DIE SET OPERATOR S MANUAL STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE Wear eye protection Use proper lubrication WARNING: FOR HAND CUTTING APPLICATIONS ONLY.
More informationCatalogue guide. MARIO PINTO SPA Strada delle Cacce Torino page 1 di 13
Catalogue guide MARIO PINTO SPA Strada delle Cacce 21-10135 Torino www.live-tooling.com www.mariopinto.it page 1 di 13 PRODUCTS MANUFACTURING PHILOSOPHY Our Live Tools are entirely developed, designed
More informationTIMTOS 2017 EXHIBITS PROFILE
TIMTOS 2017 EXHIBITS PROFILE Product Code Product Name METAL CUTTING MACHINE TOOL Lathes and Turning Machines 160101 Lathes, Swiss Type 160502 Bench Lathes 160503 High Speed Lathes 160504 Automatic Lathes
More informationCAUTION! This manual contains important information for the correct installation, operation and maintenance of the equipment described herein.
CAUTION! This manual contains important information for the correct installation, operation and maintenance of the equipment described herein. All persons involved in such installation, operation, and
More informationno mm no Dividers with scriber 150 mm NEW Square wedge-shaped knife edges on the length side
Summer Promotion valid until 30.06.2013 all quoted prices are incl. VAT for deliveries to EU countries to customers with valid VAT-no. and for deliveries in non EU member countries the VAT is not applicable
More informationSOFTSYNCHRO HIGH PERFORMANCE TAP H O L D E R S
SOFTSYNCHRO HIGH PERFORMANCE TAP H O L D E R S You Know Taps Now take them to the next level Triple your tap life and more with Emuge Softsynchro Tap Holders! E muge is widely recognized in the industry
More informationQUICK-GRIP CNC COLLET CHUCKS
QUICK-GRIP CNC COLLET CHUCKS TEN-SECOND COLLET CHANGES 0.0002" TIR OR BETTER PARALLEL GRIP COLLETS WITH A 0.062" RANGE MOST COMPACT CHUCKS IN THE INDUSTRY IN-STOCK FOR SAME-DAY SHIPPING ROYAL QUICK-GRIP
More informationPosi-Bend ROTARY BENDING SOLUTIONS
Lowers tooling costs Reduces setup time Produces bends over 90 Bends UHS steel Eliminates cam tooling to produce over bends Flexible and interchangeable Reduces down time Requires lower tonnage than traditional
More informationWRS Artificial Lift System
WRS Artificial Lift System Patent Pending Designed to adapt to any type of Artificial Lift Suspension! Artificial Lift and Down hole gauge monitoring Is fast Becoming the go to in the oil production market.
More informationALBRECHT PRECISION KEYLESS DRILL CHUCKS THE WORLD'S MOST CONSISTENTLY ACCURATE DRILL CHUCKS
ALBRECHT PRECISION KEYLESS DRILL S THE WORLD'S MOST CONSISTENTLY ACCURATE DRILL S ALBRECHT The World's Most Consistently Accurate Drill Chucks For the past 00 years, Albrecht s line of precision drill
More informationBHJ Products, Inc. Parts List & Instructions
Product Name: O-Ring Groove Cutter Page 1 of 6 Kit Contents: 1x Cutter Head Assembly with Handle & Adjustable Tool Block 1x Graduated Adjusting Screw 1x Adjustable Tool Holder 1x Carbide Insert (Size of
More informationPPC Series Precision Power Chucks
Precision Workholding Technology PPC Series Precision Power Chucks www.microcentric.com The World s Most Accurate Power Chuck Improve productivity and lower costs by enhancing workpiece quality...... through
More informationDUO-TAPTITE. Fasteners DUO-TAPTITE. Thread Rolling Screws
Fasteners Percent thread chart... Page 8 Pilot hole sizes... Page 9 Typical torque performance... Page 10 Typical single punch extruded holes... Pages 11 & 12 Die cast cored holes... Page 12 CORFLEX...
More informationQUICK-GRIP CNC COLLET CHUCKS
QUICK-GRIP CNC COLLET CHUCKS TEN-SECOND COLLET CHANGES 0.0002" TIR OR BETTER PARALLEL GRIP COLLETS WITH A 0.062" RANGE MOST COMPACT CHUCKS IN THE INDUSTRY IN-STOCK FOR SAME-DAY SHIPPING ROYAL QUICK-GRIP
More informationBy Professor Parabellum
By Professor Parabellum Introduction The following lightweight and highly compact machine pistol design is quick to manufacture and contains a low number of components. It's minimalist layout incorporates
More informationSafety And Operation Instructions RSR50 VMC Right Angle Self-Reversing Tapping Units
Safety And Operation Instructions To Avoid Serious Injury And Ensure Best Results For Your Tapping Operation, Please! Read Carefully All operator and safety instructions provided for this tapping attachment
More information