Wireless Data Gathering Panel MODEL TS0825
|
|
- Alisha Porter
- 5 years ago
- Views:
Transcription
1 Wireless Data Gathering Panel MODEL TS0825 Wireless Data Gathering Panel: Model TS0825 INSTALLATION GUIDE The TS0825 Wireless Data Gathering Panel may be installed up to 1.5km from the Challenger panel to provide cable free installation of devices such as PIR's, Smoke Detectors, Wide Gap and Universal transmitters, Single and Multi-Button pendants and Glass Break detectors. The WDGP is used to expand the Challenger by up to 16 or 32 inputs. Transmitters have a range of up to 600 metres given ideal conditions. Receiver Antenna: See Page 2 for details. Links: TERM: Link is fitted on the first and last device on the LAN segment. Programming Connector: Connects transmitters to the DGP for programming. Links: GND: This Link connects the negative of the supply to the chassis and earth lug. Programming LED: See page 3 for details. Power, Comms & Tamp: Power, LAN and Tamper connections. See page 2 for details. Tamper Switch: See page 3 for details. Comms LEDs: Communications LEDs indicating the status of Challenger communications. See page 3 for details. Address Switches: Used to identify this DGP. Revised! see Protective Earthing Addendum The Leader In Innovative Security Technology Wireless Data Gathering Panel : Model TS0825 Issue I Revision I: January
2 Installation Kit: P 1 x Wireless DGP TS0825 in an IP 55 plastic enclosure... 1 x Installation guide... 1 x Programming Guide... 2 x 3 Way Plug-on screw terminals... 2 x Jumper links... 4 x Lid screws... 4 x IP55 mounting screw caps... 1 x Programming cable... 1 x 20mm Conduit Adaptor... 1 x Adaptor Locking Ring... Installation Information: As this is a radio receiving device, all considerations given to locating a receiving antenna should be observed in order to obtain maximum effectiveness. The location of the TS0825 will be dependant on the coverage required and the type of building construction. A building of high metal content for example, may give a reduced coverage, therefore additional DGPs may be necessary to cover the total area. A general recommendation is to locate the TS0825 central to ALL transmitters and orient the antenna to face the transmitters farthest from the TS0825. Prior to installation, it may be helpful to use the Inovonics FA715 Survey Kit to determine transmission characteristics at the application site. The survey kit helps installers to determine optimal locations and orientation of the TS0825 and Inovonics FA-series tranmitters. The Inovonics FA525 Intelligent Repeater may be used to solve range or transmission problems. Ensure that the enclosure is mounted on a solid, flat surface remote from large metal objects. More detailed information regarding the location of receivers and transmitters is provided in the Inovonics Technical Presentation booklet available through Direct Alarm Supplies (DAS). Power Comms & Tamper Connections J1: J1 DC: + Positive and Negative connections to the LAN 12 volt supply - Maximum current drawn by the WDGP is 12 Volts DC NOTE: A separate power supply should be used if the WDGP is located more than 100 meters from the Challenger panel. J1 LAN: D+ RS485 Data positive and negative connection. May be up to 1.5km from D- the Challenger panel. (See Connection diagram on page 4.) J1 Tamper: T Input and Common connection for the panel Tamper Switches. C Short circuit for seal or Open circuit for unseal. (Must be sealed if not used) Can only be used with closed contacts. Earth Terminal: To provide the WDGP with proper immunity and noise protection, the Earth 2 TS0825IN.P65 Issue I Revision I: January 1999
3 Terminal should be connected to the common earth wire run with the LAN cable back to the Challenger Panel. In the case were the WDGP LAN may be isolated from the Challenger LAN, the Earth Terminal should be connected to the local supply earth. Mounting: The unit is mounted via screws through the 4 holes provided in the base. The IP55 rating can be maintained only if the 4 plastic plugs are installed over the mounting screw heads. Proper cable gland entries must be used to maintain the IP rating. Tamper Switch: The Wireless DGP enclosure is fitted with two tamper switches. If the rear Tamper switch is required to operate: Cover: (1) Drill an 8mm hole (minimum size) in the base of the enclosure as shown by the drilling template on page 5. The rounded end of the Tamper switch arm should nest freely in the hole. (2) Install a small screw into the mounting surface on which the Enclosure is to be mounted. This should protrude through the hole and be 8mm + 1mm above the enclosure mounting surface. See diagram on page 5. (3) Note that when the Enclosure is mounted, the screw will hold the rear Tamper switch closed. (4) If both Tamper switches are to be used, connect both Normally Open contacts in series and then connect them into the Tamper input of the Wireless DGP. The WDGP cover may be removed by removing the four corner screws. NOTE: When removing the cover after the system is installed, be aware that Tamper alarms are fitted to detect cover removal. Input Numbering: The WDGP can be programmed to have 16 or 32 radio inputs. See the Programming Guide for details regarding changing the number of inputs. Communication and Programming LEDs: RxD: RxD (Yellow) LED flashing or dimly lit, indictaes polling data being received on the LAN from the Challenger Panel. No flashing RxD LED indicates the LAN is not connected or a LAN fault (usually cabling) or the Challenger Panel is not operating. TxD: TxD (Red) LED flashing indicates the WDGP is replying to polling from the Challenger Panel. Wireless Data Gathering Panel : Model TS0825 Issue I Revision I: January
4 Revised! see Protective Earthing Addendum RxD LED flashing but no TxD LED flashing indicates the WDGP is not being polled by Challenger. PRG: PRG (Green) LED flashes once when the transmitted device has been programmed correctly. (See Programming Guide Page 5 "Programmer Setup Option") Dip Switch Settings: WDGP address. Set Dip switches 1 to 4 all OFF to disable the WDGP Wireless DGP Address Dip Switch Number 1 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON 2 OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON 3 OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON 4 OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON LAN System and Earth Connection Block Diagram: NOTE 1: "TERM" link should be fitted on the first and last devices on the LAN. In a "star" wiring configuration the "TERM" link is only fitted on the devices at the ends of the two longest LAN cable runs. NOTE 2: Recommended cable for Challenger LAN is Belden 8723, 2 pair twisted shielded data cable. NOTE 3: The Shield of each length of data cable is normally connected at one end only. Where the WDGP is installed in an electrical noise sensitive environment, all shields must be connected to a good earth at both ends. NOTE 4: The Earth Terminal on every piece of equipment in the system, must be properly earthed by connecting them all to one common earth point via a separate Earth wire run with the LAN to the Challenger Panel. The separate Earth wire must be at least 2.5mm2. A heavier gauge is recommended for runs over 500 metres. To meet EMC standards for Information Technology equipment EN55022 or AS/NZS3548, this method of earthing must be implemented. It will also ensure that the difference in earth potential between any Challenger product connected to the LAN, remains at an acceptable minimum at times when the system is subjected to high electrical noise stress. 4 TS0825IN.P65 Issue I Revision I: January 1999
5 WDGP Enclosure Rear Tamper Switch Drilling Template: Wireless Data Gathering Panel: Model TS mm Drill 8mm dia. + 9mm Rear of Enclosure Tamper Switch Screw 8mm Enclosure Mounting Surface Wireless Data Gathering Panel : Model TS0825 Issue I Revision I: January
6 ACN Please note, this product conforms to the standards set by Standards Australia on behalf of the Australian Telecommunications Authority (AUSTEL) and the Spectrum Management Agency (SMA). WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. The Challenger is Designed and Manufactured by: Tecom Systems Pty. Ltd. A.C.N Whitehorse Road MITCHAM VIC AUST 3132 Telephone: Facsimile: Tecom Systems TS0825IN.P65 Issue I Revision I: January 1999
Wireless Data Gathering Panel (DGP) Model AL-1231
g GE Security Wireless Data Gathering Panel (DGP) Model AL-1231 Installation & Programming Guide Installation and Programming Guide Wireless DGP AL-1231 Part number: 466-2025-US Rev. H April 2005 Contents
More informationCOD GB / 1.0 RBAND/UMS - RBAND/CSM
INTRODUCTION DESCRIPTION The RadioBand system is designed of Industrial, Commercial and Domestic door and gate applications where a safety edge is used. The system provides a wireless system replacing
More informationIntelPage 5W (POCSAG) Transmitter
A division of NESS CORPORATION PTY LTD IntelPage 5W (POCSAG) Transmitter INSTALLATION MANUAL IntelPage 5W (POCSAG) Transmitter Installation Manual v1.2 1. Contents 1. Contents... 1 2. Equipment List...
More information1.0 Introduction. Related Products and Documentation
Quick Start t Guide ER450 Data Radio 1.0 Introduction Welcome to the Quick Start Guide for the ER450 Data Radio. This guide provides step-by-step instructions, with simple explanations to get you up-and-running.
More informationSF C-Series. 900 MHz Wireless Switch Follower/Remote Control Receiver (with On-Board 10-Amp Relays) Typical Applications
Long Range Wireless Applications 900 MHz Wireless Switch Follower/Remote Control Receiver (with On-Board 10-Amp Relays) The SF900C Series Remote Control/Switch Followers are a twoway system designed to
More informationG703. Installation instructions. residential gate opener for sliding gates. remote control openers security at your fingertips
remote control openers security at your fingertips G703 residential gate opener for sliding gates Installation instructions Toll free helpline Please have your serial number and model name available before
More informationOEM WIRELESS DIALLER USER MANUAL
OEM WIRELESS DIALLER USER MANUAL (Product No. 100-023) CONTENTS INTRODUCTION...1 FEATURES...2 WIRELESS PENDANTS...3 DISPLAYS AND WARNINGS...5 SPECIFICATIONS...6 INTRODUCTION Your OEM Wireless Dialler has
More informationNess M1RF Wireless Receiver
INSTALLATION MANUAL Ness M1RF Wireless Receiver Specifications, Installation and Programming Page 1 (Version 1.4 - May 2008) Ness Document No. 895-364 APPLICATION The Ness M1RF Receiver is a unique high
More informationWiring Instructions for 10, 16 & 20 Function, 92 & 93 Series, FET Receivers.
Wiring Instructions for 10, 16 & 20 Function, 92 & 93 Series, FET Receivers. 92220.02E 1 1. The Receiver is designed to carry a maximum of 15 Amps. That is, for example,15 Amps through one output or 5
More informationSF C-Series. 900 MHz Wireless Switch Follower/Remote Control Receiver (with On-Board 10-Amp Relays) Typical Applications
Long Range Wireless Applications 900 MHz Wireless Switch Follower/Remote Control Receiver (with On-Board 10-Amp Relays) The SF900C Series Remote Control/Switch Followers are a twoway system designed to
More informationLMLR-710 (Plug-in type door chime receiver) LMLT-711 (push unit door chime transmitter)
MODEL: LMLR-710 (Plug-in type door chime receiver) LMLT-711 (push unit door chime transmitter) FEATURE: * 67 million self-learning coding RF wireless operation system. No interference with neighbors. *
More informationM-Bus Master MultiPort 250L Installation and User Guide
Installation and User Guide Kamstrup A/S Industrivej 28, Stilling DK-8660 Skanderborg T: +45 89 93 10 00 info@kamstrup.com kamstrup.com Contents 1 Introduction 3 1.1 Design 3 2 Functionality 4 2.1 Overview
More informationProduct Catalog: Europe
Product Catalog: Europe Table of Contents Market Solutions 1 Commercial Security 2 Commercial Monitoring Transmitters 3 Pendant 4 Universal 5 Commercial Monitoring 6 Specialized 7 Motion Detector Receivers
More informationInstallation & Operating Manual. iwap202
Installation & Operating Manual iwap202 This page is intentionally left blank. Document Number 409345 (based on 407655) (See Last Page for Revision Details) For warranty information, refer to Terms and
More informationProduct Catalog: Europe
Product Catalog: Europe Table of Contents Market Solutions 1 Commercial Security 2 Commercial Monitoring Transmitters 3 Pendant 4 Universal 5 Commercial Monitoring 6 Specialized 7 Motion Detector Receivers
More informationFA401 Single Transmitter / Single Output Receiver. FA401R Single Transmitter / Single Relay Output Receiver. Installation Instructions 02305C
FA401 Single Transmitter / Single Output Receiver FA401R Single Transmitter / Single Relay Output Receiver Frequency Agile 900MHz Installation Instructions 02305C Note: The FA401 is intended to be installed
More informationDR-TRC105-EV Evaluation Kit. User s Guide
DR-TRC105-EV Evaluation Kit User s Guide DR-TRC105-304-EV DR-TRC105-315-EV DR-TRC105-345-EV DR-TRC105-372-EV DR-TRC105-390-EV DR-TRC105-403-EV DR-TRC105-434-EV DR-TRC105-450-EV 2010-2015 by Murata Electronics
More informationInstallation Notes. SCR Single Channel
Installation Notes SCR Single Channel Receiver Part No. 100-187 Receives ARM / Disarm / PANIC / Low Batt channels from Ness Radio Keys or Radio PIRs / Radio Reeds. Supports up to four transmitters. Simple
More informationAMB-1200C Deactivator Controller and AMB-1200A Countertop Antenna
AMB-1200C Deactivator Controller and AMB-1200A Countertop Antenna Installation Guide Regulatory Restriction: In certain countries, there may be installation restrictions on the antennas. See antenna installation
More informationOEM WIRELESS DIALLER INSTALLATION & USER MANUAL. (Product No )
OEM WIRELESS DIALLER INSTALLATION & USER MANUAL (Product No. 100-023) CONTENTS 1. INTRODUCTION... 2 2. FEATURES... 2 3. EQUIPMENT LIST... 3 4. INSTALLATION... 3 5. PROGRAM MODE... 4 5.1 To Enter Program
More informationOutside Temperature Sensors
1 814 1814P01 Symaro Outside Temperature Sensors QAC31 Active sensors for acquiring the outside temperature Operating voltage AC 24 V or DC 13535 V Signal output DC 010 V or 420 ma Use The QAC31 outside
More informationIMMS-CI-HW. Communications Controller Interface. Installation Instructions IMMS. Controller. Interface. AC From Transformer 24 VAC REM 24 VAC SEN
CI 4 Comm. IMMS-CI-HW Communications Interface POWER From Transformer Ground To REM Installation Instructions To SmartPort Sensor 1 Sensor 2 Sensor 3 From Sensors Sensor Common IMMS Interface From SI or
More informationUniversal Voice Coil and 70 Volt Door Speaker V / V
PagePac by ISSUE 2 Universal Voice Coil and 70 Volt Door Speaker V-5330120 / V-5330230 Installation Manual 947179 Your PagePac Door Speaker Note: The Door Phone Controller and PagePac 6 systems require
More informationModel PA2204A Load Cell Combiner Module Instruction Manual
Model PA2204A Load Cell Combiner Module Instruction Manual AMALGAMATED INSTRUMENT CO PTY LTD ACN: 001 589 439 Unit 5, 28 Leighton Place Hornsby Telephone: +61 2 9476 2244 e-mail: sales@aicpl.com.au NSW
More informationWISENMESHNET Smart Gateway
WISENMESHNET Smart Gateway User Manual Wisen Innovation Ltd July 2014 Revision History and Clarification Rev. Issue Date Revisions Written By Revised By V5.0 20/06/2014 1 st Issue Tony Shi Yan Wu V6.0
More informationRADIOBAND V3 Programming & Installation Manual
RADIOBAND V3 Programming & Installation Manual Radioband V3 User s Manual Introduction The RadioBand system is designed for Automatic Gates, Commercial and Domestic door applications where a safety edge
More informationWIRELESS Energy Monitor - Smart Meter
Energy saving made simple MONITOR CONTROL SAVE WIRELESS Energy Monitor - Smart Meter Monitors your electricity use and cost in real time Instruction Manual EW4500 IMPORTANT Please retain your Instruction
More informationMLR-1105 (DC battery type door chime receiver) LMLT-711 (push unit door chime transmitter)
MODEL: MLR-1105 (DC battery type door chime receiver) LMLT-711 (push unit door chime transmitter) FEATURE: * 67 million self-learning coding RF wireless operation system. No interference with neighbors.
More informationRS 485/422 to Fibre Optic Modems ELO E243, ELO E244, ELO E245. Operation manual
RS 485/422 to Fibre Optic Modems ELO E243, ELO E244, ELO E245 Operation manual 1.0 Introduction 3 2.0 Operation principles 3 3.0 Installation 3 3.1 RS422 Interface Connection 4 3.2 RS485 Interface Connection
More informationOSMAC RDR Low-voltage Retrofit Kit
OSMAC RDR Low-voltage Retrofit Kit Part Number RDR0160LVN0 User s Guide Installation of the RDR (Radio Data Receiver) low-voltage unit will enable you to remotely operate your existing Vari-Time 4000 satellite
More informationModular Radio Telemetry System
Simple to Use Remote Control 8 Channels per Transmitter 16 Channels per Receiver Upto 48 Transmitters per system Auto Transmit Mode Secure RF Protocol Automatic Watchdog Transmission Range: Upto 200 metres
More informationCardMaster RF Installation Manual Rev
CardMaster RF Installation Manual Rev 09.12.09 Installation Manual for CardMaster fuel control www.cardlockvending.com Customers call 888-487-5040 www.cardlockvending.com customers call 888-487-5040 8.0
More informationINSTALLATION INSTRUCTIONS FOR THE CLIKCARD COMMERCIAL RECEIVER (NARROW BAND)
Doc. 6001200 Rev. B INSTALLATION INSTRUCTIONS FOR THE CLIKCARD COMMERCIAL RECEIVER (NARROW BAND) TABLE OF CONTENTS TABLE OF CONTENTS...1 INSTALLATION FOR INFINITY AND PROCARD...3 PULLING CABLE... 3 MOUNTING
More informationWireless 900 MHz Receiver
Overview and Identification The 900 MHz unit receives a repeated or re-transmitted RF signal from one or more wireless temperature or humidity transmitters. The signal from the transmitter (418 MHz) is
More informationThe wireless alternative to expensive cabling...
The wireless alternative to expensive cabling... ELPRO 105U ISO 9001 Certified New Products... New Solutions The ELPRO 105 range of telemetry modules provide remote monitoring and control by radio or twisted-pair
More informationModular Radio Telemetry System
Simple to Use Remote Control 8 Channels per Transmitter 16 Channels per Receiver Upto 48 Transmitters per system Auto Transmit Mode Secure RF Protocol Automatic Watchdog Transmission Range: Upto 200 metres
More informationHigh power radio transmission module MR03 type
High power radio transmission module MR03 type User s manual CONTENTS 1. APPLICATION...3 2. MR03 MODULE SET...4 3. INSTALLATION...4 3.1 Module assembly...4 3.2 Connection diagrams...5 3.3 Connection way
More information+GF+ SIGNET Temperature Transmitter Instructions
GF SIGNET 80- Temperature Transmitter Instructions ENGLISH -80.090- B-/00 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal
More informationRadio Control Installation and Operating Instructions System 4
Radio Control Installation and Operating Instructions System 4 P.O. Box 403, One Cedar Parkway, Jackson, WI 53037 Phone: 800-628-1909 Fax: 262-677-2058 Revision: April 19, 2012 Contents Introduction 3
More informationPRO Professional Radio Control Series Applications
204 205 Ready to Use Remote Control 4, 8/16 Channel Systems Range: Up to 200 metres at 433MHz Up to 1,000 metres at 433MHz NB Relay Outputs: Momentary, Latching, Timed Receiver IP65 Applications Lighting
More information200, 201 Series Radio Telemetry Transmitters
200 DIN Rail Transmitter Encoder Up to 8 Input Channels Volt Free contact Inputs via Screw Terminals 12 / 24Vdc Supply Range; 433MHz Up to 200 Metres 433MHz NB Up to 1,000 Metres 458MHz Up to 6,000 Metres
More informationSTI REPEATER HOW THE PRODUCT WORKS BEFORE YOU START. Installation and Operation Manual. Model: STI-34109
Installation and Operation Manual STI REPEATER Model: STI-34109 Thank you for purchasing this fine product. Your satisfaction is very important to us. Please read this manual carefully to get the most
More informationJUMO Wtrans Receiver Universal Receiver for JUMO Wireless Measuring Probes
Data sheet 902931 Page 1/10 JUMO Wtrans Receiver Universal Receiver for JUMO Wireless Measuring Probes For processing physical measurands of the JUMO Wtrans series RS485 interface with Modbus protocol
More informationRadio receivers type DB317 and DBR1-M4
Radio receivers type DB317 and DBR1-M4 User manual Art no 006176 Technical data DB317 DBR1-M4 Dimensions (WxHxD) 45x75x21 mm 80x80x50 mm Supply Voltage via control panel 12/24 VAC/VDC Current Consumption
More informationInstallation guide 873 SmartRadar Control Unit & Antenna Unit
Installation guide 873 SmartRadar Control Unit & Antenna Unit Rev. 7 January 2006 Part no. 4416.569 Enraf BV PO Box 812 2600 AV Delft Netherlands Tel. : +31 15 2701 100 Fax : +31 15 2701 111 E-mail : info@enraf.nl
More informationTS-930: Installing the Inrad Roofing Filter Mod
TS-930: Installing the Inrad Roofing Filter Mod The TS-930 roofing filter mod consists of a 6 pole, 4 to 5 khz wide filter followed by a high dynamic range, feedback amplifier. The amplifier provides enough
More informationThe wireless alternative to expensive cabling...
The wireless alternative to expensive cabling... ELPRO 905U Wireless Solutions for Process Applications New Products... New Solutions The ELPRO 905U range of telemetry modules provide remote monitoring
More informationsat-nms LBRX L-Band Beacon Receiver User Manual
sat-nms LBRX L-Band Beacon Receiver User Manual Version 2.5 / 2018-02-02 Copyright SatService Gesellschaft für Kommunikatiosnsysteme mbh Hardstrasse 9 D-78256 Steisslingen www.satnms.com www.satservicegmbh.de
More informationWDMX-512. user manual
WDMX-512 user manual Measurements are in millimeters. WDMX512 Standard model 195 50 125 223 436 44 482 182 WDMX512 ProDiversity model 2003 Martin Professional A/S, Denmark. All rights reserved. No part
More informationWireless multizone receiver RDE-MZ6
s 1 428 Wireless multizone receiver RDE-MZ6 for floor heating / zone heating systems Mains-powered RDE-MZ6 multizone wireless receiver (AC 230 V) DIN rail mounting 2-position control with On/Off output
More informationRadio Link Starter Kit
Radio Link Starter Kit Installation Manual BARTLETT Instrument Co. 1032 Avenue H Fort Madison, IA 52627 319-372-8366 www.bartinst.com Table of Contents Radio Link Starter Kit Manual... 3 System Requirements...
More informationCA80 Series Vari-Angle IR Illuminator
CA80 Series Vari-Angle IR Illuminator Installation Guide Rev. 1.0 QIG Part no.: L625000100G 100% 75% 50% 25% Dimming Zoom LED On/Off LED Status 50% 20% 10% Revision History: * Rev. 1.0: Initial Release
More informationPROMUX Distributed MODBUS I/O Modules Catalog and Design Guide
PROMUX Distributed MODBUS I/O Modules Catalog and Design Guide 12/03/2012 V11.0 P.O.Box 164 Seven Hills 1730 NSW AUSTRALIA Tel: +61 2 96248376 Fax: +61 2 9620 8709 Email: proconel@proconel.com Web: www.proconel.com
More information02/11/2015
Modem communication plug and play solutions GSM Part number 88970119 For remote control of your application Automatic notification of alarms via SMS (GSM Modem) / email or on a PC with M3 ALARM software.
More informationHub and Cluster. ogramming Manual. Pro MAN3090
Hub and Cluster Pro ogramming Manual MAN3090 Contents Introduction 3 Radio Channels 28 System Overview 3 Currently Used 30 RCC RCC Ch 30 System Design 4 Device RCC Ch 30 Manual Select 30 Compatibility
More informationUser Manual CXE Rev.002 Broadband Cable Networks March 3, (10) CXX Series. User Manual. Teleste Corporation CXE880.
Broadband Cable Networks March 3, 2008 1(10) CXX Series User Manual Teleste Corporation CXE880 Fibre Node Broadband Cable Networks March 3, 2008 2(10) Introduction The CXE880 is a fibre deep optical node
More informationMD12-2 Metal Loop Detector
MD12-2 Metal Loop Detector Features Supply 12VDC Adjustable sensitivity (8 levels via dip switch) 2 x Relay outputs (each can be configured individually) Power up and loop activation LED indicator. Industry
More informationP700WLS IoProx Receiver
Installation Manual Warning! This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual
More informationInstallation and Operation Manual MSI. Multi-Sensor Interface Hub. Interface Module for all Sensors Network and Wireless CAUTION
Installation and Operation Manual MSI Multi-Sensor Interface Hub Interface Module for all Sensors Network and Wireless CAUTION This equipment complies with the limits for a Class B digital device, pursuant
More informationTRC EV DR TRC EV DR TRC EV
DR-TRC103-EV Evaluation Kit User s Guide DR TRC103 868 EV DR TRC103 915 EV DR TRC103 950 EV DR-TRC103-EV User s Guide (2015/04/17) Page 1 of 11 www.murata.com Introduction The DR TRC103 series evaluation
More informationUSER MANUAL. MODEL 2017A RS-232 to 20ma Current Loop Converter. SALES OFFICE (301) TECHNICAL SUPPORT (301)
USER MANUAL MODEL 2017A RS-232 to 20ma Current Loop Converter Part# 07M2017A-A Doc# 073021UA Revised 10/15/93 SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www.patton.com 1.0 WARRANTY
More informationAstra-R Kit Wireless Alarm System Operation Manual
Astra-R Kit Wireless Alarm System Operation Manual This operation manual describes principles of functioning, proper use, maintenance and service for the wireless alarm system Astra- R Kit (Figure 1).
More informationInstallation & Operation Manual for D2066 Quasar Receiver
Installation & Operation Manual for D2066 Quasar Receiver For software version v0024 Dycon Ltd Tel: +44 (0)1443 471 060 Fax: +44 (0)1443 479 374 Cwm Cynon Business Park Mountain Ash CF45 4ER - UK www.dyconsecurity.eu
More informationPROFLY / PROBLADE Professional Radio Control PRO-BLADE8
PRO-BLADE8 Ready to Use Remote Control 8 Channel Systems Range: PROFLY Up to 100 metres PROBLADE Up to 500 metres Relay Outputs: Momentary, Latching, Timed Receiver IP65 Applications Lighting Control General
More informationGROUP OF COMPANIES. MERLIN STEALTH Electric Fence Energizer INSTALLERS MANUAL
GROUP OF COMPANIES MERLIN STEALTH Electric Fence Energizer INSTALLERS MANUAL Revision 1.5 23 February 2007 : INSTALLERS MANUAL Table of Contents 2 INTRODUCTION.. 3 INSTALLER OPTIONS...... 4-11 ALARM SETTING
More informationIntroduction...1 Overview...2. Beacon Transmitter...7. Beacon Receiver Trouble Shooting...15
MoTeC Lap Beacon Manual Contents Introduction...1 Overview...2 Operation...2 ID Number...3 Lap Beacon Use...4 Split Beacon Use...4 Verifying Operation...5 Beacon Transmitter...7 Position...7 Spacing between
More informationMDS SD4 Software-Controlled Digital Communications Firmware Release 1.x.x
MDS SD4 Software-Controlled Digital Communications Start-Up Guide Firmware Release 1.x.x MDS 05-4669A01, Rev. A December 2007 OPERATIONAL & SAFETY NOTICES RF Exposure Concentrated energy from a directional
More informationWireless Room Temperature and Humidity Transmitter (Units without Temperature Setpoint or Override) Installation and Operating Instructions
Wireless Temperature and Humidity Overview and Indentification The Wireless Temperature and Humidity measures the room temperature and Relative Humidity and transmits the data at 418MHz or 433MHz RF to
More informationELSEMA 1,2,3,4,8 -Channel 433MHz GIGALINK Transmitter GLT43300,GLT43301,GLT43302,GLT43303,GLT43304,GLT43308
433MHz HAND HELD GIGALINK TRANSMITTERS GLT43300, GLT43301, GLT43302, GLT43303, GLT43304 and GLT43308 Features One, two, three, four & eight buttons. More than four billion code combinations Ability to
More informationJUMO Wtrans Receiver with Wireless Data Transmission
Data Sheet 902931 Page 1/10 JUMO Wtrans Receiver with Wireless Data Transmission k For measuring temperature, pressure, potentiometer, and voltage. k Interface RS485 with Modbus protocol k Wireless measured
More informationHeritage MedCall. Sentry E-Call Model HM-527 Resident Host Panel
Heritage MedCall Sentry E-Call Model HM-527 Resident Host Panel 430-527B 0305 Heritage MedCall, Inc. Issue 1, March 2005 Heritage Medcall Sentry Emergency Call System Model 527 Host Panel Installation
More informationGMS-xx GSR-IAxx User Manual Appendix Simple Interconnection Network
GMS-xx GSR-IAxx User Manual Appendix Simple Interconnection Network GeoSIG Ltd, Ahornweg 5A, 5504 Othmarsingen, Switzerland Phone: + 41 44 810 2150, Fax: + 41 44 810 2350 info@geosig.com, www.geosig.com
More informationCS-200. PORTABLE TRAFFIC LIGHT CONTROLLER (Software 1.05) OPERATION AND SERVICE MANUAL
CS-200 PORTABLE TRAFFIC LIGHT CONTROLLER (Software 1.05) OPERATION AND SERVICE MANUAL CS-200 Operation and Service Manual Page 2 Manufactured by: LINCAST INTERNATIONAL PTY. LTD. 2/3 Sir Laurence Drive
More informationUser Manual CXE Rev (12) CXX Series. User Manual. Teleste Corporation. CXE880 Fibre node
17.12.2012 1(12) CXX Series User Manual Teleste Corporation CXE880 Fibre node 17.12.2012 2(12) Contents Introduction... 3 Installation... 3 Housing... 3 Powering... 3 Status monitoring card (optional)...
More informationPOWER DELEGATOR SERIES 7200A POWER DISTRIBUTION UNIT WITH POWER CONDITIONING GENERAL SPECIFICATIONS
POWER DELEGATOR SERIES 7200A POWER DISTRIBUTION UNIT WITH POWER CONDITIONING GENERAL SPECIFICATIONS 1.0 SCOPE The following specification describes the features, design, and application of the Series 7200A
More informationRoom Sensors. for relative humidity and temperature
1 857 1857P01 Room Sensors for relative humidity and temperature QFA20 Operating voltage AC 24 V or DC 13535 V Signal output DC 010 V for relative humidity Signal output DC 010 V or LG-Ni 1000 or T1 for
More informationRoom Sensors. In ventilating and air conditioning plants to acquire relative humidity and temperature in rooms. Humidity measuring range
1 857 1857P01 Room Sensors for relative humidity and temperature QFA20 Use Operating voltage AC 24 V or DC 13535 V Signal output DC 010 V for relative humidity Signal output DC 010 V or LG-Ni 1000 or T1
More informationP700-WLS ioprox Receiver
Installation Manual DN1628-1611 Pre-Installation Notes Copyright 2016 Tyco International Ltd. and its Respective Companies. All Rights Reserved. All specifications were current as of publication date and
More informationEMC Test Report. Report Number: M030826
Page 1 of 36 EMC Technologies Pty Ltd ABN 82 057 105 549 57 Assembly Drive Tullamarine Victoria Australia 3043 Ph: + 613 9335 3333 Fax: + 613 9338 9260 email: melb@emctech.com.au EMC Test Report Report
More informationSpectrian 2304 MHz SSPA. Garry C. Hess, K3SIW June 11, 2004
Spectrian 2304 MHz SSPA Garry C. Hess, K3SIW June 11, 2004 A solid-state power amplifier (SSPA) manufactured by Spectrian can produce on the order of 200 W linear output 1 at 2304 MHz with little modification.
More informationGSM-900 Contact ID Cellular Backup System Installation Manual
GSM-900 Contact ID Cellular Backup System Installation Manual Rev. 1.01-08/11/08 Table of Contents Introduction... 3 1.0 Parts Needed to Complete this Installation... 3 2.0 Activation and Installation...
More informationConnecting Mains Electrical Power
Tide Level Monitoring Instrumentation The following documentation details the electrical installation for the tide level monitoring instrumentation and also a summary of the logger configurations required
More informationDisclaimers. Important Notice
Disclaimers Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
More informationInstallation Instructions
SYSTXBBSAM01 EVOLUTION SYSTEM ACCESS MODULE Installation Instructions NOTE: Read the entire instruction manual before starting the installation. pointsett U.S. Pat No. 7,415,102 Fig. 1 - Evolution System
More informationREIMESCH KOMMUNIKATIONSSYSTEME GMBH ALPIN HF / 50MHz Linear Amplifier - USER MANUAL. v1.1
REIMESCH KOMMUNIKATIONSSYSTEME GMBH ALPIN 100 - HF / 50MHz Linear Amplifier - USER MANUAL v1.1 DECLARATION OF CONFORMITY I hereby declare that the product: ALPIN 100, HF/6m 1kW Linear Amplifier satisfies
More informationHardware Guide. Control Made Simple. Model 401A Signal Generator
Control Made Simple Model 401A Signal Generator Hardware Guide ON OFF LIMIT 1 2 3 4 RXD TXD POWER West Coast Office 1263 El Camino Real Menlo Park, CA 94025 Phone (650) 853-1444 Fax (650) 853-1405 www.flashcutcnc.com
More informationIMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION
INSTALLATI INSTRUCTIS Model: RB-G-K10 IMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIS BEFORE BEGINNING INSTALLATI The Miller Edge RBand Monitored Gate Edge Transmitter/Receiver system is intended to provide
More informationADA-1028L. User manual ADA-1028L. RS232 to Current Loop 2-wire CLO Converter. 1 io_ada-1028l_v.1.10_en. Copyright CEL-MAR sp.j.
User manual ADA-1028L to Current Loop 2-wire Converter Copyright 2001-2017 CEL-MAR sp.j. 1 io_ada-1028l_v.1.10_en Contents 1. GENERAL INFORMATION... 3 1.1. WARRANTED INFORMATION... 3 1.2. GENERAL CONDITIONS
More informationRAIN-CLIK. Rain Sensor With Optional Freeze Shutoff for Automatic Irrigation Systems. Owner s Manual and Installation Instructions
RAIN-CLIK Rain Sensor With Optional Freeze Shutoff for Automatic Irrigation Systems Owner s Manual and Installation Instructions For use with WR-CLIK and WRF-CLIK Sensors TABLE OF CONTENTS Features...3
More informationUSER MANUAL Digital Wireless Gateway U9120-W4 (P/N: 44002G-01)
USER MANUAL Digital Wireless Gateway U9120-W4 (P/N: 44002G-01) 19549P-82 (11-16) 2016 DAVID CLARK COMPANY INCORPORATED Cautions and Warnings READ AND SAVE THESE INSTRUCTIONS. Follow the instructions in
More informationFC-868-SE2 Survey Kit User Guide
FC-868-SE2 Survey Kit User Guide 2018 EMS Ltd. All rights reserved. MK144 (Iss 3) 30/10/2018 AJM Contents Start 3 Introduction 4 About The Survey Kit 5 Survey Kit Overview 6 Signal Surveyor Features 7
More informationIMMS-R. IMMS-R Radio Module. Installation Instructions POWER. Controller. Comm.
IMMS-R IMMS-R Radio Module Installation Instructions TABLE OF CONTENTS... Before you install... 1 Key Specifications... 2 Important Installation notes... 3 Installation... 3 Interface Installation... 4
More informationShort form User Manual
Nortech Detection Pty Ltd Unit1, Bldg 5, Forest Central Business Park, 49 Frenchs Forest Road, Frenchs Forest NSW 2086 PO Box 6011, Frenchs Forest DC, NSW 2086 Tel: 02 8977 4047 Fax: 02 9475 4742 email:
More informationLONG RANGE REMOTE RECEIVER WITH TRANSMITTER FOR BUNGALOWS AND BANKS MODEL KE - 2 L R
REMOTE RECEIVER DIMENSION : L = 90 MM X H = 75 X D = 38 MM. R F RANGE FOR TRANSMITTER AND RECEIVER IS 20 TO 30 METERS IN CLOSED AREA R F SIGNAL CROSSED WOODEN, R C C WALL, GLASS, AND METAL DOORS REMOTE
More informationHome Automation, Inc. Omnistat2. RC-1000 and RC-2000 Communicating Thermostat. Serial Protocol Description
Home Automation, Inc. Omnistat2 RC-1000 and RC-2000 Communicating Thermostat Serial Protocol Description This document contains the intellectual property of Home Automation, Inc. (HAI). HAI authorizes
More informationRF-RR-T 24V Powered Routers/Temp Sensors
Page 1 of 5 RF-RR-T 24V Powered Routers/Temp Sensors Features: Benefits: Proven 802.15.4 low power network Complete range of sensor types Allows networks to be expanded Power status LED Network activity
More information02/11/2015
Modem communication plug and play solutions GSM Part number 88970119 For remote control of your application Automatic notification of alarms via SMS (GSM Modem) / email or on a PC with M3 ALARM software.
More informationINSTRUCTION MANUAL DAAB LOOP DETECTOR DB402
INSTRUCTION MANUAL DAAB LOOP DETECTOR DB402 1st Edition Revision: 3 FAAC Nordic AB BOX 125, SE-284 22 PERSTORP SWEDEN TEL. +46 435 77 95 00 FAX +46 435 77 95 29 www.faac.se Contents Technical data...2
More informationWLS-5500 Receiver (KSF & W26)
WLS-5500 Receiver (KSF & W26) Installation Manual DN1869-0912 Warning! This manual contains information on limitations regarding product use and function and information on the limitations as to liability
More informationRadio Link Starter Kit
Radio Link Starter Kit Installation Manual BARTLETT Instrument Co. 1032 Avenue H Fort Madison, IA 52627 319-372-8366 www.bartinst.com Table of Contents Radio Link Starter Kit Manual... 3 System Requirements...
More information