ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 11 of this data sheet.
|
|
- Ashlyn Cummings
- 6 years ago
- Views:
Transcription
1 The MC3320/2/4 family of operational amplifiers provide railtorail operation on both the input and output. The inputs can be driven as high as 200 mv beyond the supply rails without phase reversal on the outputs, and the output can swing within 50 mv of each rail. This railtorail operation enables the user to make full use of the supply voltage range available. It is designed to work at very low supply voltages (± 0.9 V) yet can operate with a supply of up to +2 V and ground. Output current boosting techniques provide a high output current capability while keeping the drain current of the amplifier to a minimum. Also, the combination of low noise and distortion with a high slew rate and drive capability make this an ideal amplifier for audio applications. Low Voltage, Single Supply Operation (+. V and Ground to +2 V and Ground) Input Voltage Range Includes both Supply Rails Output Voltage Swings within 50 mv of both Rails No Phase Reversal on the Output for Overdriven Input Signals High Output Current (I SC = 0 ma, Typ) Low Supply Current (I D = 0.9 ma, Typ) 600 Ω Output Drive Capability Extended Operating Temperature Ranges (40 to +05 C and 55 to +25 C) Typical Gain Bandwidth Product = 2.2 MHz 4 4 PDIP P, VP SUFFIX CASE 626 SO D, VD SUFFIX CASE 75 Micro DM SUFFIX CASE 46A PDIP4 P, VP SUFFIX CASE 646 SO4 D, VD SUFFIX CASE 75A 4 TSSOP4 DTB SUFFIX CASE 94G ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page of this data sheet. DEVICE MARKING INFORMATION See general marking information in the device marking section on page of this data sheet. Semiconductor Components Industries, LLC, 2002 January, 2002 Rev. 6 Publication Order Number: MC3320/D
2 MC3320, MC33202, MC33204 PIN CONNECTIONS CASE 626 CASE 646/75A/94G CASE 75/46A This device contains 70 active transistors (each amplifier). Figure. Circuit Schematic (Each Amplifier) 2
3 MC3320, MC33202, MC33204 MAXIMUM RATINGS Rating Symbol Value Unit Supply Voltage (V CC to V EE ) V S +3 V Input Differential Voltage Range V IDR Note. V Common Mode Input Voltage Range (Note 2.) V CM V CC V to V EE 0.5 V Output Short Circuit Duration t s Note 3. sec Maximum Junction Temperature T J +50 C Storage Temperature T stg 65 to +50 C Maximum Power Dissipation P D Note 3. mw V DC ELECTRICAL CHARACTERISTICS (T A = 25 C) Characteristic V CC = 2.0 V V CC = 3.3 V V CC = 5.0 V Unit Input Offset Voltage V IO (max) MC3320 MC33202 MC33204 ±.0 ±0 ±2 ±.0 ±0 ±2 ± 6.0 ±.0 ±0 mv Output Voltage Swing V OH (R L = 0 kω) V OL (R L = 0 kω) Power Supply Current per Amplifier (I D ) Specifications at V CC = 3.3 V are guaranteed by the 2.0 V and 5.0 V tests. V EE = Gnd V min V max ma DC ELECTRICAL CHARACTERISTICS (V CC = V, V EE = Ground, T A = 25 C, unless otherwise noted.) Characteristic Figure Symbol Min Typ Max Unit Input Offset Voltage (V CM 0 V to 0.5 V, V CM.0 V to 5.0 V) 3 V IO mv MC3320: T A = + 25 C 6.0 MC3320: T A = 40 to +05 C 9.0 MC3320V: T A = 55 to +25 C 3 MC33202: T A = + 25 C.0 MC33202: T A = 40 to +05 C MC33202V: T A = 55 to +25 C 4 MC33204: T A = + 25 C 0 MC33204: T A = 40 to +05 C 3 MC33204V: T A = 55 to +25 C 7 Input Offset Voltage Temperature Coefficient (R S = 50 Ω) T A = 40 to +05 C T A = 55 to +25 C Input Bias Current (V CM = 0 V to 0.5 V, V CM =.0 V to 5.0 V) T A = + 25 C T A = 40 to +05 C T A = 55 to +25 C Input Offset Current (V CM = 0 V to 0.5 V, V CM =.0 V to 5.0 V) T A = + 25 C T A = 40 to +05 C T A = 55 to +25 C 4 V IO / T 5, 6 I IB I IO Common Mode Input Voltage Range V ICR V EE V CC V. The differential input voltage of each amplifier is limited by two internal parallel backtoback diodes. For additional differential input voltage range, use current limiting resistors in series with the input pins. 2. The input common mode voltage range is limited by internal diodes connected from the inputs to both supply rails. Therefore, the voltage on either input must not exceed either supply rail by more than 500 mv. 3. Power dissipation must be considered to ensure maximum junction temperature (T J ) is not exceeded. (See Figure 2) µv/ C na na 3
4 MC3320, MC33202, MC33204 DC ELECTRICAL CHARACTERISTICS (cont.) (V CC = V, V EE = Ground, T A = 25 C, unless otherwise noted.) Characteristic Figure Symbol Min Typ Max Unit Large Signal Voltage Gain (V CC = V, V EE = 5.0 V) R L = 0 kω R L = 600 Ω Output Voltage Swing (V ID = ± 0.2 V) R L = 0 kω R L = 0 kω R L = 600 Ω R L = 600 Ω 7 A VOL 50 25, 9, 0 Common Mode Rejection (V in = 0 V to 5.0 V) CMR db V OH V OL V OH V OL kv/v V Power Supply Rejection Ratio V CC /V EE = 5.0 V/Gnd to 3.0 V/Gnd 2 PSRR µv/v Output Short Circuit Current (Source and Sink) 3, 4 I SC 50 0 ma Power Supply Current per Amplifier (V O = 0 V) T A = 40 to +05 C T A = 55 to +25 C 5 I D ma AC ELECTRICAL CHARACTERISTICS (V CC = V, V EE = Ground, T A = 25 C, unless otherwise noted.) Characteristic Figure Symbol Min Typ Max Unit Slew Rate 6, 26 SR V/µs (V S = ± 2.5 V, V O = 2.0 V to V, R L = 2.0 kω, A V = +.0) Gain Bandwidth Product (f = 00 khz) 7 GBW 2.2 MHz Gain Margin (R L = 600 Ω, C L = 0 pf) 20, 2, 22 A M 2 db Phase Margin (R L = 600 Ω, C L = 0 pf) 20, 2, 22 M 65 Deg Channel Separation (f =.0 Hz to 20 khz, A V = 00) 23 CS 90 db Power Bandwidth (V O = 4.0 V pp, R L = 600 Ω, THD %) BW P 2 khz Total Harmonic Distortion (R L = 600 Ω, V O =.0 V pp, A V =.0) f =.0 khz f = 0 khz 24 THD % Open Loop Output Impedance (V O = 0 V, f = 2.0 MHz, A V = 0) Z O 00 Ω Differential Input Resistance (V CM = 0 V) R in 200 kω Differential Input Capacitance (V CM = 0 V) C in.0 pf Equivalent Input Noise Voltage (R S = 00 Ω) f = 0 Hz f =.0 khz 25 e n nv/ Hz Equivalent Input Noise Current f = 0 Hz f =.0 khz 25 i n pa/ Hz 4
5 MC3320, MC33202, MC33204 Figure 2. Maximum Power Dissipation versus Temperature Figure 3. Input Offset Voltage Distribution µ Figure 4. Input Offset Voltage Temperature Coefficient Distribution Figure 5. Input Bias Current versus Temperature Ω Figure 6. Input Bias Current versus Common Mode Voltage Figure 7. Open Loop Voltage Gain versus Temperature 5
6 MC3320, MC33202, MC33204 Ω ± ± ± ± ± ± Ω Figure. Output Voltage Swing versus Supply Voltage Figure 9. Output Saturation Voltage versus Load Current Figure 0. Output Voltage versus Frequency Figure. Common Mode Rejection versus Frequency Figure 2. Power Supply Rejection versus Frequency Figure 3. Output Short Circuit Current versus Output Voltage 6
7 MC3320, MC33202, MC33204 ± Figure 4. Output Short Circuit Current versus Temperature ± ± ± ± ± ± Figure 5. Supply Current per Amplifier versus Supply Voltage with No Load µ ± Figure 6. Slew Rate versus Temperature Figure 7. Gain Bandwidth Product versus Temperature ± Ω Ω ± ± ± ± Figure. Voltage Gain and Phase versus Frequency Figure 9. Voltage Gain and Phase versus Frequency 7
8 MC3320, MC33202, MC33204 Ω Figure 20. Gain and Phase Margin versus Temperature Ω Ω Figure 2. Gain and Phase Margin versus Differential Source Resistance Figure 22. Gain and Phase Margin versus Capacitive Load Figure 23. Channel Separation versus Frequency Ω Figure 24. Total Harmonic Distortion versus Frequency Figure 25. Equivalent Input Noise Voltage and Current versus Frequency
9 MC3320, MC33202, MC33204 DETAILED OPERATING DESCRIPTION General Information The MC3320/2/4 family of operational amplifiers are unique in their ability to swing railtorail on both the input and the output with a completely bipolar design. This offers low noise, high output current capability and a wide common mode input voltage range even with low supply voltages. Operation is guaranteed over an extended temperature range and at supply voltages of 2.0 V, 3.3 V and 5.0 V and ground. Since the common mode input voltage range extends from V CC to V EE, it can be operated with either single or split voltage supplies. The MC3320/2/4 are guaranteed not to latch or phase reverse over the entire common mode range, however, the inputs should not be allowed to exceed maximum ratings. Circuit Information Railtorail performance is achieved at the input of the amplifiers by using parallel NPNPNP differential input stages. When the inputs are within 00 mv of the negative rail, the PNP stage is on. When the inputs are more than 00 mv greater than V EE, the NPN stage is on. This switching of input pairs will cause a reversal of input bias currents (see Figure 6). Also, slight differences in offset voltage may be noted between the NPN and PNP pairs. Crosscoupling techniques have been used to keep this change to a minimum. In addition to its railtorail performance, the output stage is current boosted to provide 0 ma of output current, enabling the op amp to drive 600 Ω loads. Because of this high output current capability, care should be taken not to exceed the 50 C maximum junction temperature. Ω Ω µ µ Figure 26. Noninverting Amplifier Slew Rate Figure 27. Small Signal Transient Response Ω µ Figure 2. Large Signal Transient Response 9
10 MC3320, MC33202, MC33204 MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to ensure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will selfalign when subjected to a solder reflow process. Micro inches mm 0
11 MC3320, MC33202, MC33204 Operational Amplifier Function Single Device ORDERING INFORMATION Operating Temperature Range Package Shipping MC3320D SO 9 Units / Rail MC3320DR2 T A= 40 to +05 C SO 2500 Units / Tape & Reel MC3320P Plastic DIP 50 Units / Rail MC3320VD T A = 55 to 25 C SO 9 Units / Rail MC33202D SO 9 Units / Rail MC33202DR2 MC33202DMR2 T A = 40 to +05 C SO Micro 2500 Units / Tape & Reel 4000 Units / Tape & Reel Dual MC33202P Plastic DIP 50 Units / Rail Quad MC33202VD SO 9 Units / Rail MC33202VDR2 T A = 55 to 25 C SO 2500 Units / Tape & Reel MC33202VP Plastic DIP 50 Units / Rail MC33204D SO4 55 Units / Rail MC33204DR2 SO Units / Tape & Reel MC33204DTB T A= 40 to +05 C TSSOP4 96 Units / Rail MC33204DTBR2 TSSOP Units / Tape & Reel MC33204P Plastic DIP 25 Units / Rail MC33204VD SO4 55 Units / Rail MC33204VDR2 T A = 55 to 25 C SO Units / Tape & Reel MC33204VP Plastic DIP 25 Units / Rail MARKING DIAGRAMS SO D SUFFIX CASE 75 SO VD SUFFIX CASE 75 PDIP P SUFFIX CASE 626 PDIP VP SUFFIX CASE 626 Micro DM SUFFIX CASE 46A 3320x ALYW 320xV ALYW MC3320xP AWL YYWW MC33202VP AWL YYWW 3202 AYW 4 SO4 D SUFFIX CASE 75A 4 SO4 VD SUFFIX CASE 75A 4 PDIP4 P SUFFIX CASE PDIP4 VP SUFFIX CASE 646 TSSOP4 DTB SUFFIX CASE 94G 4 MC33204D AWLYWW MC33204VD AWLYWW MC33204P AWLYYWW x = or 2 A = Assembly Location WL, L = Wafer Lot YY, Y = Year WW, W = Work Week MC33204VP AWLYYWW MC ALYW
12 MC3320, MC33202, MC33204 PACKAGE DIMENSIONS PDIP P, VP SUFFIX CASE ISSUE L B NOTE 2 T H F A G C N D K L J M SO D, VD SUFFIX CASE 7507 ISSUE W X B Y Z H G A D S C N X 45 M K J 2
13 MC3320, MC33202, MC33204 PACKAGE DIMENSIONS B PDIP4 P, VP SUFFIX CASE ISSUE M T N A F L C K J H G D 4 PL M SO4 D, VD SUFFIX CASE 75A03 ISSUE F A B P 7 PL T G D 4 PL K C R X 45 M J F 3
14 MC3320, MC33202, MC33204 PACKAGE DIMENSIONS TSSOP4 DTB SUFFIX CASE 94G0 ISSUE O L T 2X L/2 PIN IDENT. D C 4X K REF N M B U A V G H N J J F DETAIL E K K ÇÇ ÉÉ SECTION NN DETAIL E W 4
15 MC3320, MC33202, MC33204 PACKAGE DIMENSIONS Micro DM SUFFIX CASE 46A02 ISSUE E K A B PIN ID T G D PL C H J L 5
16 MC3320, MC33202, MC33204 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 563, Denver, Colorado 027 USA Phone: or Toll Free USA/Canada Fax: or Toll Free USA/Canada ONlit@hibbertco.com N. American Technical Support: Toll Free USA/Canada JAPAN: ON Semiconductor, Japan Customer Focus Center 432 NishiGotanda, Shinagawaku, Tokyo, Japan 4003 Phone: r4525@onsemi.com ON Semiconductor Website: For additional information, please contact your local Sales Representative. 6 MC3320/D
MARKING DIAGRAMS ORDERING INFORMATION Figure 1. Representative Schematic Diagram (Each Amplifier) DUAL MC33078P
The MC33078/9 series is a family of high quality monolithic amplifiers employing Bipolar technology with innovative high performance concepts for quality audio and data signal processing applications.
More informationMARKING DIAGRAMS ORDERING INFORMATION DUAL MC33272AP AWL YYWW PDIP 8 P SUFFIX CASE 626 SO 8 D SUFFIX CASE ALYWA QUAD
The MC33272/74 series of monolithic operational amplifiers are quality fabricated with innovative Bipolar design concepts. This dual and quad operational amplifier series incorporates Bipolar inputs along
More informationPIN CONNECTIONS ORDERING INFORMATION PIN CONNECTIONS P SUFFIX PLASTIC PACKAGE CASE 626 D SUFFIX PLASTIC PACKAGE CASE 751 (SO 8) Inputs P SUFFIX
Quality bipolar fabrication with innovative design concepts are employed for the MC33181/2/4, MC34181/2/4 series of monolithic operational amplifiers. This JFET input series of operational amplifiers operates
More informationMARKING DIAGRAMS Split Supplies Single Supply PIN CONNECTIONS MAXIMUM RATINGS ORDERING INFORMATION SO 14 D SUFFIX CASE 751A
The MC3403 is a low cost, quad operational amplifier with true differential inputs. The device has electrical characteristics similar to the popular MC1741C. However, the MC3403 has several distinct advantages
More informationMC Low Voltage Rail-To-Rail Sleep Mode Operational Amplifier
MC3334 Low Voltage Rail-To-Rail Sleep Mode Operational Amplifier The MC3334 is a monolithic bipolar operational amplifier. This low voltage rail to rail amplifier has both a rail to rail input and output
More informationLOW POWER JFET INPUT OPERATIONAL AMPLIFIERS
These JFET input operational amplifiers are designed for low power applications. They feature high input impedance, low input bias current and low input offset current. Advanced design techniques allow
More informationMC34085BP HIGH PERFORMANCE JFET INPUT OPERATIONAL AMPLIFIERS
These devices are a new generation of high speed JFET input monolithic operational amplifiers. Innovative design concepts along with JFET technology provide wide gain bandwidth product and high slew rate.
More informationMC33201, MC33202, MC33204, NCV33202, NCV33204
MC3320, MC33202, MC33204, NCV33202, NCV33204 Low Voltage, RailtoRail Operational Amplifiers The MC3320/2/4 family of operational amplifiers provide railtorail operation on both the input and output. The
More informationMC33201, MC33202, MC33204, NCV33202, NCV Low Voltage, Rail-to-Rail Operational Amplifiers
MC332, MC3322, MC3324, NCV3322, NCV3324 Low Voltage, Rail-to-Rail Operational Amplifiers The MC332/2/4 family of operational amplifiers provide railtorail operation on both the input and output. The inputs
More informationMARKING DIAGRAMS PIN CONNECTIONS ORDERING INFORMATION MC3x58P1 AWL YYWW PDIP 8 P1 SUFFIX CASE 626 SO 8 D SUFFIX CASE 751 3x58 ALYW
Utilizing the circuit designs perfected for the quad operational amplifiers, these dual operational amplifiers feature: low power drain, a common mode input voltage range extending to ground/v EE, and
More informationPIN CONNECTIONS
Utilizing the circuit designs perfected for Quad Operational Amplifiers, these dual operational amplifiers feature low power drain, a common mode input voltage range extending to ground/v EE, and single
More informationMAXIMUM RATINGS (T A = +25 C, unless otherwise noted.) PIN CONNECTIONS
The LM324 series are low cost, quad operational amplifiers with true differential inputs. They have several distinct advantages over standard operational amplifier types in single supply applications.
More informationORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 17 of this data sheet.
Quality bipolar fabrication with innovative design concepts are employed for the MC3307/72/74, MC3407/72/74 series of monolithic operational amplifiers. This series of operational amplifiers offer 4.5
More informationMC33078, MC MARKING DIAGRAMS. Features
MC337, MC3379 Low Noise Dual/Quad Operational Amplifiers The MC337/9 series is a family of high quality monolithic amplifiers employing Bipolar technology with innovative high performance concepts for
More informationMARKING DIAGRAMS PIN CONNECTIONS ORDERING INFORMATION
The MC346/MC336 are universal voltage monitors intended for use in a wide variety of voltage sensing applications. These devices offer the circuit designer an economical solution for positive and negative
More informationP SUFFIX CASE 646 Single Supply Split Supplies SO-14 D SUFFIX CASE 751A PIN CONNECTIONS
Dual Operational Amplifier and Dual Comparator The MC05 contains two differential-input operational amplifiers and two comparators, each set capable of single supply operation. This operational amplifier-comparator
More informationTCA0372, TCA0372B. 1.0 A Output Current, Dual Power Operational Amplifiers
.0 A Output Current, Dual Power Operational Amplifiers The TCA0372 is a monolithic circuit intended for use as a power operational amplifier in a wide range of applications, including servo amplifiers
More informationMARKING DIAGRAMS PIN CONNECTIONS ORDERING INFORMATION PDIP 8 N SUFFIX CASE 626 LM311D AWL YYWW SO 8 98 Units/Rail
The ability to operate from a single power supply of 5.0 V to 30 V or 15 V split supplies, as commonly used with operational amplifiers, makes the LM211/LM311 a truly versatile comparator. Moreover, the
More informationMARKING DIAGRAMS Figure 1. Logic Diagram ORDERING INFORMATION Figure 2. Dip Pin Assignment CDIP 16 L SUFFIX CASE 620A
The MC0H6 is a functional/pinout duplication of the MC06, with 00% improvement in propagation delay and no increase in power supply current. Propagation Delay,.0 ns Typical Power Dissipation 85 mw Typ/Pkg
More informationMC33502/D. 1.0 V, Rail to Rail, Dual Operational Amplifier
MC3352. V, Rail to Rail, Dual Operational Amplifier The MC3352 operational amplifier provides rail to rail operation on both the input and output. The output can swing within 5 mv of each rail. This rail
More informationMARKING DIAGRAMS LOGIC DIAGRAM ORDERING INFORMATION DIP PIN ASSIGNMENT CDIP 16 L SUFFIX CASE 620 MC10124L AWLYYWW
The MC024 is a quad translator for interfacing data and control signals between a saturated logic section and the MECL section of digital systems. The MC024 has TTL compatible inputs, and MECL complementary
More informationThe MC10109 is a dual 4 5 input OR/NOR gate. P D = 30 mw typ/gate (No Load) t pd = 2.0 ns typ t r, t f = 2.0 ns typ (20% 80%)
The MC10109 is a dual 5 input OR/NOR gate. P D = 0 mw typ/gate (No Load) t pd =.0 ns typ t r, t f =.0 ns typ (0% 0%) LOGIC DIAGRAM MARKING DIAGRAMS CDIP 16 L SUFFIX CASE 60 PDIP 16 P SUFFIX CASE 6 PLCC
More informationAudio Equipment Instrumentation and Control Circuits Telephone Channel Amplifiers Medical Equipment. Features PIN CONNECTIONS
NE3, SA3, SE3, NE3A, SA3A, SE3A Single Low Noise Operational Amplifier The NE/SA/SE3/3A are single high-performance low noise operational amplifiers. Compared to other operational amplifiers, such as TL3,
More informationMARKING DIAGRAMS LOGIC DIAGRAM ORDERING INFORMATION DIP PIN ASSIGNMENT CDIP 16 L SUFFIX CASE 620 MC10216L AWLYYWW
The MC1016 is a high speed triple differential amplifier designed for use in sensing differential signals over long lines. The base bias supply (V BB ) is made available at pin 11 to make the device useful
More informationLM339S, LM2901S. Single Supply Quad Comparators
LM339S, LM290S Single Supply Quad Comparators These comparators are designed for use in level detection, low level sensing and memory applications in consumer and industrial electronic applications. Features
More informationDUAL TIMING CIRCUIT SEMICONDUCTOR TECHNICAL DATA PIN CONNECTIONS ORDERING INFORMATION. Figure Second Solid State Time Delay Relay Circuit
The MC3456 dual timing circuit is a highly stable controller capable of producing accurate time delays, or oscillation. Additional terminals are provided for triggering or resetting if desired. In the
More informationMC33272A, MC33274A, NCV33272A, NCV33274A. Single Supply, High Slew Rate, Low Input Offset Voltage Operational Amplifiers
MC33272A, MC3327A, NCV33272A, NCV3327A Single Supply, High Slew Rate, Low Input Offset Voltage Operational Amplifiers The MC33272/7 series of monolithic operational amplifiers are quality fabricated with
More informationMC34071,2,4,A MC33071,2,4,A, NCV33074A
MC07,,,A MC07,,,A, NCV07A Single Supply.0 V to V Operational Amplifiers Quality bipolar fabrication with innovative design concepts are employed for the MC07/7/7, MC07/7/7 series of monolithic operational
More informationPIN CONNECTIONS ORDERING INFORMATION FUNCTIONAL TABLE
The MC12026 is a high frequency, low voltage dual modulus prescaler used in phase locked loop (PLL) applications. The MC12026A can be used with CMOS synthesizers requiring positive edges to trigger internal
More informationTIMING CIRCUIT SEMICONDUCTOR TECHNICAL DATA ORDERING INFORMATION. Figure Second Solid State Time Delay Relay Circuit
The MC1455 monolithic timing circuit is a highly stable controller capable of producing accurate time delays or oscillation. Additional terminals are provided for triggering or resetting if desired. In
More informationGENERAL PURPOSE TRANSISTOR ARRAY
The MC3346 is designed for general purpose, low power applications for consumer and industrial designs. Guaranteed BaseEmitter Voltage Matching Operating Current Range Specified: 10 µa to 10 ma Five General
More informationPNP Silicon Surface Mount Transistor with Monolithic Bias Resistor Network
Preferred Devices PNP Silicon Surface Mount Transistor with Monolithic Bias Resistor Network This new series of digital transistors is designed to replace a single device and its external resistor bias
More informationLM393, LM293, LM2903, LM2903V, NCV2903. Low Offset Voltage Dual Comparators
, LM293, LM293, LM293V, NCV293 Low Offset Voltage Dual Comparators The series are dual independent precision voltage comparators capable of single or split supply operation. These devices are designed
More informationEMC5DXV5T1, EMC5DXV5T5
EMC5DXV5T, EMC5DXV5T5 Preferred Devices Dual Common Base Collector Bias Resistor Transistors NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network The BRT (Bias Resistor Transistor)
More informationMC14001B Series. B Suffix Series CMOS Gates MC14001B, MC14011B, MC14023B, MC14025B, MC14071B, MC14073B, MC14081B, MC14082B
MC4B Series B Suffix Series CMOS Gates MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B The B Series logic gates are constructed with P and N channel enhancement mode devices in a single monolithic structure
More informationNSTB1005DXV5T1, NSTB1005DXV5T5. Dual Common Base Collector Bias Resistor Transistors
NSTB005DXV5T, NSTB005DXV5T5 Preferred Devices Dual Common Base Collector Bias Resistor Transistors NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network The BRT (Bias Resistor
More informationMC3488A. Dual EIA 423/EIA 232D Line Driver
Dual EIA423/EIA232D Line Driver The MC34A dual is singleended line driver has been designed to satisfy the requirements of EIA standards EIA423 and EIA232D, as well as CCITT X.26, X.2 and Federal Standard
More informationMC14066BF. MARKING DIAGRAMS. MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 2.) ORDERING INFORMATION PDIP 14 P SUFFIX CASE 646
The MC14066B consists of four independent switches capable of controlling either digital or analog signals. This quad bilateral switch is useful in signal gating, chopper, modulator, demodulator and CMOS
More informationMARKING DIAGRAMS MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 1.) ORDERING INFORMATION PDIP 14 P SUFFIX CASE 646
The MC14106B hex Schmitt Trigger is constructed with MOS P channel and N channel enhancement mode devices in a single monolithic structure. These devices find primary use where low power dissipation and/or
More informationOutputs Source/Sink 24 ma ACT157 Has TTL Compatible Inputs. Figure 1. Pinout: 16 Lead Packages Conductors (Top View) PIN NAME
The MC74AC157/74ACT157 is a high speed quad 2 input multiplexer. Four bits of data from two sources can be selected using the common Select and Enable inputs. The four outputs present the selected data
More informationPIN CONNECTIONS
The NCP4421/4422 are high current buffer/drivers capable of driving large MOSFETs and IGBTs. They are essentially immune to any form of upset except direct overvoltage or over dissipation they cannot be
More informationNCS2004, NCS2004A. 3.5 MHz, Wide Supply, Rail-to-Rail Output Operational Amplifier
NCS, NCSA. MHz, Wide Supply, Rail-to-Rail Output Operational Amplifier The NCS operational amplifier provides rail to rail output operation. The output can swing within 7 mv to the positive rail and mv
More informationMC33064DM 5 UNDERVOLTAGE SENSING CIRCUIT
The MC34064 is an undervoltage sensing circuit specifically designed for use as a reset controller in microprocessor-based systems. It offers the designer an economical solution for low voltage detection
More informationNCS2005. Operational Amplifier, Low Power, 8 MHz GBW, Rail-to-Rail Input-Output
Operational Amplifier, Low Power, 8 MHz GBW, Rail-to-Rail Input-Output The provides high performance in a wide range of applications. The offers beyond rail to rail input range, full rail to rail output
More informationLM393, LM293, LM2903, LM2903V, NCV2903, NCV2903V. Low Offset Voltage Dual Comparators
, LM293, LM293, LM293V, NCV293, NCV293V Low Offset Voltage Dual Comparators The series are dual independent precision voltage comparators capable of single or split supply operation. These devices are
More informationMARKING DIAGRAMS LOGIC DIAGRAM PIN ASSIGNMENT ORDERING INFORMATION FUNCTION TABLE DIP 14 N SUFFIX CASE 646 MC74HC4066AN AWLYYWW
High Performance Silicon Gate CMOS The MC74HC466A utilizes silicon gate CMOS technology to achieve fast propagation delays, low ON resistances, and low OFF channel leakage current. This bilateral switch/
More informationNST3906DXV6T1, NST3906DXV6T5. Dual General Purpose Transistor
NST396DXV6T1, NST396DXV6T5 Dual General Purpose Transistor The NST396DXV6T1 device is a spin off of our popular SOT23/SOT323 threeleaded device. It is designed for general purpose amplifier applications
More informationLM321. Single Channel Operational Amplifier
Single Channel Operational Amplifier LM32 is a general purpose, single channel op amp with internal compensation and a true differential input stage. This op amp features a wide supply voltage ranging
More informationMC3403, MC3303. Single Supply Quad Operational Amplifiers
MC0, MC0 Single Supply Quad Operational Amplifiers The MC0 is a low cost, quad operational amplifier with true differential inputs. The device has electrical characteristics similar to the popular MC7C.
More informationNCS MHz Voltage Feedback Op Amp
75 MHz Voltage Feedback Op Amp NCS255 is a 75 MHz voltage feedback monolithic operational amplifier featuring high slew rate and low differential gain and phase error. The voltage feedback architecture
More informationPNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network
Preferred Devices PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network This new series of digital transistors is designed to replace a single device and its external resistor bias
More informationLM339, LM239, LM2901, LM2901V, NCV2901, MC3302. Single Supply Quad Comparators
LM339, LM239, LM290, LM290V, NCV290, MC3302 Single Supply Quad Comparators These comparators are designed for use in level detection, low level sensing and memory applications in consumer, automotive,
More informationEMF5XV6T5G. Power Management, Dual Transistors. NPN Silicon Surface Mount Transistors with Monolithic Bias Resistor Network
Preferred Devices Power Management, Dual Transistors NPN Silicon Surface Mount Transistors with Monolithic Bias Resistor Network Features Simplifies Circuit Design Reduces Board Space Reduces Component
More information10 AMPERE DARLINGTON COMPLEMENTARY SILICON POWER TRANSISTORS VOLTS 125 WATTS MAXIMUM RATINGS THERMAL CHARACTERISTICS TIP141 TIP142
... designed for general purpose amplifier and low frequency switching applications. High DC Current Gain Min h FE = 1000 @ I C = 5 A, V CE = 4 V Collector Emitter Sustaining Voltage @ 30 ma V CEO(sus)
More informationNSTB1002DXV5T1G, NSTB1002DXV5T5G
NSTB002DXV5TG, NSTB002DXV5T5G Preferred Devices Dual Common BaseCollector Bias Resistor Transistors NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network The BRT (Bias Resistor
More informationMJD44H11 (NPN) MJD45H11 (PNP)
MJDH (NPN) MJD5H (PNP) Preferred Device Complementary Power Transistors For Surface Mount Applications Designed for general purpose power and switching such as output or driver stages in applications such
More informationBAV70DXV6T1, BAV70DXV6T5 Preferred Device. Monolithic Dual Switching Diode Common Cathode. Lead-Free Solder Plating.
BAV70DXV6T1, BAV70DXV6T5 Preferred Device Monolithic Dual Switching Diode Common Cathode LeadFree Solder Plating MAXIMUM RATINGS (EACH DIODE) Rating Symbol Value Unit Reverse Voltage V R 70 Vdc Forward
More informationNSVEMD4DXV6T5G. Dual Bias Resistor Transistors. NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network
Dual Bias Resistor Transistors NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network The BRT (Bias Resistor Transistor) contains a single transistor with a monolithic bias
More informationPERIPHERAL DRIVER ARRAYS
The seven NPN Darlington connected transistors in these arrays are well suited for driving lamps, relays, or printer hammers in a variety of industrial and consumer applications. Their high breakdown voltage
More informationMUN5211DW1T1 Series. NPN Silicon Surface Mount Transistors with Monolithic Bias Resistor Network
MUNDWT Series Preferred Devices Dual Bias Resistor Transistors NPN Silicon Surface Mount Transistors with Monolithic Bias Resistor Network The BRT (Bias Resistor Transistor) contains a single transistor
More informationORDERING INFORMATION Figure 1. Pinout: 20 Lead Packages Conductors (Top View) PIN ASSIGNMENT
The MC74AC273/74ACT273 has eight edge-triggered D type flip flops with individual D inputs and Q outputs. The common buffered Clock (CP) and Master Reset (MR) inputs load and reset (clear) all flip flops
More informationMUN5311DW1T1G Series.
MUNDWTG Series Preferred Devices Dual Bias Resistor Transistors NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network The Bias Resistor Transistor (BRT) contains a single
More informationMMBT3906TT1G. General Purpose Transistors. PNP Silicon GENERAL PURPOSE AMPLIFIER TRANSISTORS SURFACE MOUNT
General Purpose Transistors PNP Silicon This transistor is designed for general purpose amplifier applications. It is housed in the SOT46/SC75 package which is designed for low power surface mount applications.
More informationPZTA92T1. High Voltage Transistor. PNP Silicon SOT 223 PACKAGE PNP SILICON HIGH VOLTAGE TRANSISTOR SURFACE MOUNT
High Voltage Transistor PNP Silicon Features These Devices are Pb Free, Halogen Free/BFR Free and are RoHS Compliant MAXIMUM RATINGS (T C = 25 C unless otherwise noted) Rating Symbol Value Unit Collector-Emitter
More informationMJD44H11 (NPN) MJD45H11 (PNP) Complementary Power Transistors. DPAK For Surface Mount Applications
MJDH (NPN) MJD5H (PNP) Complementary Power Transistors For Surface Mount Applications Designed for general purpose power and switching such as output or driver stages in applications such as switching
More informationORDERING INFORMATION Figure 1. Pinout: 20 Lead Packages Conductors (Top View) PIN ASSIGNMENT
The MC74AC574/74ACT574 is a high speed, low power octal flip flop with a buffered common Clock (CP) and a buffered common Output Enable (OE). The information presented to the D inputs is stored in the
More informationHigh Performance Silicon Gate CMOS
High Performance Silicon Gate CMOS The MC74HC4316A utilizes silicon gate CMOS technology to achieve fast propagation delays, low ON resistances, and low OFF channel leakage current. This bilateral switch/multiplexer/
More informationLOW POWER SCHOTTKY. MARKING DIAGRAMS GUARANTEED OPERATING RANGES
The SN74LS373 consists of eight latches with 3-state outputs for bus organized system applications. The flip-flops appear transparent to the data (data changes asynchronously) when Latch Enable (LE) is
More informationLM393, LM293, LM2903, LM2903V, NCV2903. Low Offset Voltage Dual Comparators
, LM293, LM293, LM293V, NCV293 Low Offset Voltage Dual Comparators The series are dual independent precision voltage comparators capable of single or split supply operation. These devices are designed
More informationThis document, MC74HC4066/D has been canceled and replaced by MC74HC4066A/D LAN was sent 9/28/01
http://onsemi.com This document, MC74HC4066/D has been canceled and replaced by MC74HC4066A/D LAN was sent 9/28/01 High Performance Silicon Gate CMOS The MC54/74HC4066 utilizes silicon gate CMOS technology
More informationMJD (NPN) MJD (PNP) THERMAL CHARACTERISTICS Characteristic Symbol Max Unit Thermal Resistance, Junction to Case R JC C/W Thermal Resistance, Junction
MJD (NPN) MJD (PNP) Complementary Plastic Power Transistors NPN/PNP Silicon For Surface Mount Applications Designed for low voltage, low power, high gain audio amplifier applications. Features Collector
More informationNTA4001N, NVA4001N. Small Signal MOSFET. 20 V, 238 ma, Single, N Channel, Gate ESD Protection, SC 75
Small Signal MOSFET V, 8 ma, Single, N Channel, Gate ESD Protection, SC 75 Features Low Gate Charge for Fast Switching Small.6 x.6 mm Footprint ESD Protected Gate AEC Q Qualified and PPAP Capable NVA4N
More informationMJ PNP MJ NPN. Silicon Power Transistors 16 AMP COMPLEMENTARY SILICON POWER TRANSISTORS 250 VOLTS, 250 WATTS
MJ293 - PNP MJ294 - NPN Silicon Power Transistors The MJ293 (PNP) and MJ294 (NPN) utilize Perforated Emitter technology and are specifically designed for high power audio output, disk head positioners
More informationMR2520LRL. Overvoltage Transient Suppressor OVERVOLTAGE TRANSIENT SUPPRESSOR VOLTS
Overvoltage Transient Suppressor Designed for applications requiring a low voltage rectifier with reverse avalanche characteristics for use as reverse power transient suppressors. Developed to suppress
More informationCS PIN CONNECTIONS AND MARKING DIAGRAM ORDERING INFORMATION SO 14 D SUFFIX CASE 751A V CC. = Assembly Location
The CS3361 integral alternator regulator integrated circuit provides the voltage regulation for automotive, 3 phase alternators. It drives an external logic level N channel enhancement power FET for control
More informationMMBT3906LT3G. PNP Silicon. Pb-Free Packages are Available. Features. MAXIMUM RATINGS THERMAL CHARACTERISTICS MARKING DIAGRAM
Preferred Device General Purpose Transistor PNP Silicon Features PbFree Packages are Available MAXIMUM RATINGS Rating Symbol Value Unit Collector Emitter Voltage V CEO 4 Collector Base Voltage V CBO 4
More informationUnidirectional*
Unidirectional* Mosorb devices are designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge capability, low zener
More informationSA575. Low Voltage Compandor
Low Voltage Compandor The SA575 is a precision dual gain control circuit designed for low voltage applications. The SA575 s channel is an expandor, while channel 2 can be configured either for expandor,
More informationNGB18N40CLB, NGB18N40ACLB. Ignition IGBT 18 Amps, 400 Volts. N Channel D 2 PAK. 18 AMPS, 400 VOLTS V CE(on) 2.0 I C = 10 A, V GE 4.
NGB8N4CLB, NGB8N4ACLB Ignition IGBT 8 Amps, 4 Volts N Channel D PAK This Logic Level Insulated Gate Bipolar Transistor (IGBT) features monolithic circuitry integrating ESD and Over Voltage clamped protection
More informationNTNUS3171PZ. Small Signal MOSFET. 20 V, 200 ma, Single P Channel, 1.0 x 0.6 mm SOT 1123 Package
NTNUS7PZ Small Signal MOSFET V, ma, Single P Channel,. x.6 mm SOT Package Features Single P Channel MOSFET Offers a Low R DS(on) Solution in the Ultra Small. x.6 mm Package. V Gate Voltage Rating Ultra
More informationLOW POWER SCHOTTKY. GUARANTEED OPERATING RANGES ORDERING INFORMATION
The SN74LS298 is a Quad 2-Port Register. It is the logical equivalent of a quad 2-input multiplexer followed by a quad 4-bit edge-triggered register. A Common Select input selects between two 4-bit input
More informationUMC2NT1, UMC3NT1, UMC5NT1
UMCNT, UMC3NT, UMC5NT Preferred Devices Dual Common BaseCollector Bias Resistor Transistors NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network The Bias Resistor Transistor
More informationMJW0281A (NPN) MJW0302A (PNP) Complementary NPN PNP Power Bipolar Transistors 15 AMPERES COMPLEMENTARY SILICON POWER TRANSISTORS 260 VOLTS 150 WATTS
MJW28A (NPN) MJW32A (PNP) Preferred Devices Complementary NPN PNP Power Bipolar Transistors These complementary devices are lower power versions of the popular MJW328A and MJW32A audio output transistors.
More informationNTJS4405N, NVJS4405N. Small Signal MOSFET. 25 V, 1.2 A, Single, N Channel, SC 88
NTJSN, NVJSN Small Signal MOSFET V,. A, Single, N Channel, SC 88 Features Advance Planar Technology for Fast Switching, Low R DS(on) Higher Efficiency Extending Battery Life AEC Q Qualified and PPAP Capable
More informationLOW DROPOUT DUAL VOLTAGE REGULATOR
The LM293 is a dual positive.0 low dropout voltage regulator, designed for standby power systems. The main output is capable of supplying 70 ma for microprocessor power, and can be turned on and off by
More informationNPN Silicon Surface Mount Transistor with Monolithic Bias Resistor Network
Preferred Device NPN Silicon Surface Mount Transistor with Monolithic Bias Resistor Network This new series of digital transistors is designed to replace a single device and its external resistor bias
More informationNTGD4167C. Power MOSFET Complementary, 30 V, +2.9/ 2.2 A, TSOP 6 Dual
Power MOSFET Complementary, 3 V, +.9/. A, TSOP 6 Dual Features Complementary N Channel and P Channel MOSFET Small Size (3 x 3 mm) Dual TSOP 6 Package Leading Edge Trench Technology for Low On Resistance
More informationNJL3281D (NPN) NJL1302D (PNP) Complementary ThermalTrak Transistors BIPOLAR POWER TRANSISTORS 15 A, 260 V, 200 W
NJL3281D (NPN) NJL132D (PNP) Complementary ThermalTrak Transistors The ThermalTrak family of devices has been designed to eliminate thermal equilibrium lag time and bias trimming in audio amplifier applications.
More informationLow Capacitance Transient Voltage Suppressors / ESD Protectors CM QG/D. Features
Low Capacitance Transient Voltage Suppressors / ESD Protectors CM1250-04QG Features Low I/O capacitance at 5pF at 0V In-system ESD protection to ±8kV contact discharge, per the IEC 61000-4-2 international
More informationNUP4302MR6T1G. Schottky Diode Array for Four Data Line ESD Protection
Schottky Diode Array for Four Data Line ESD Protection The NUP432MR6 is designed to protect high speed data line interface from ESD, EFT and lighting. Features Very Low Forward Voltage Drop Fast Switching
More informationNGD18N40CLBT4G. Ignition IGBT 18 Amps, 400 Volts N Channel DPAK. 18 AMPS 400 VOLTS V CE(on) 2.0 I C = 10 A, V GE 4.5 V
NGD8NCLB Ignition IGBT 8 Amps, Volts N Channel DPAK This Logic Level Insulated Gate Bipolar Transistor (IGBT) features monolithic circuitry integrating ESD and Over Voltage clamped protection for use in
More informationNVLJD4007NZTBG. Small Signal MOSFET. 30 V, 245 ma, Dual, N Channel, Gate ESD Protection, 2x2 WDFN Package
NVLJD7NZ Small Signal MOSFET V, 2 ma, Dual, N Channel, Gate ESD Protection, 2x2 WDFN Package Features Optimized Layout for Excellent High Speed Signal Integrity Low Gate Charge for Fast Switching Small
More information1 AMPERE GENERAL PURPOSE POWER TRANSISTORS VOLTS 30 WATTS *MAXIMUM RATINGS THERMAL CHARACTERISTICS (2)
...designed for driver circuits, switching, and amplifier applications. These high performance plastic devices feature: Low Saturation Voltage VCE(sat) = 0.6 Vdc (Max) @ IC = 1.0 Amp Excellent Power Dissipation
More informationMJL21195 (PNP), MJL21196 (NPN) Silicon Power Transistors 16 A COMPLEMENTARY SILICON POWER TRANSISTORS 250 V, 200 W
MJL21195 (PNP), MJL21196 (NPN) Silicon Power Transistors The MJL21195 and MJL21196 utilize Perforated Emitter technology and are specifically designed for high power audio output, disk head positioners
More informationBD809 (NPN), BD810 (PNP) Plastic High Power Silicon Transistor 10 AMPERE POWER TRANSISTORS 80 VOLTS 90 WATTS
BD89 (NPN), BD8 (PNP) Plastic High Power Silicon Transistor These devices are designed for use in high power audio amplifiers utilizing complementary or quasi complementary circuits. Features DC Current
More informationMMSZ5221BT1 Series. Zener Voltage Regulators. 500 mw SOD 123 Surface Mount
MMSZ5BT Series Preferred Device Zener Voltage Regulators 5 mw SOD 3 Surface Mount Three complete series of Zener diodes are offered in the convenient, surface mount plastic SOD 3 package. These devices
More informationMAXIMUM RATINGS (T A = 25 C, unless otherwise noted.) STANDARD APPLICATION
These voltage regulators are monolithic integrated circuits designed as fixedvoltage regulators for a wide variety of applications including local, oncard regulation. These regulators employ internal current
More informationBC857BTT1G. General Purpose Transistor. PNP Silicon
General Purpose Transistor PNP Silicon These transistors are designed for general purpose amplifier applications. They are housed in the SOT46/SC75 which is designed for low power surface mount applications.
More informationFour Transistors Equal Power Each. Watts mw/ C Watts mw/ C TJ, Tstg 55 to +150 C. Characteristic Symbol Min Max Unit
PNP/NPN Silicon Voltage and current are negative for PNP transistors MAXIMUM RATINGS Rating Symbol Value Unit Collector Emitter Voltage VCEO 40 Vdc Collector Base Voltage VCB 40 Vdc Emitter Base Voltage
More informationMPSA20. Amplifier Transistor. NPN Silicon. Pb Free Package is Available* Features. MAXIMUM RATINGS THERMAL CHARACTERISTICS
MPSA Amplifier Transistor NPN Silicon Features Pb Free Package is Available* MAXIMUM RATINGS Rating Symbol Value Unit Collector Emitter Voltage V CEO 4 Vdc Collector Base Voltage V CBO 4. Vdc Collector
More information