Very Low Power 8-Bit 32 khz RTC Module with Digital Trimming and High Level Integration
|
|
- Dorthy Marcia Floyd
- 6 years ago
- Views:
Transcription
1 EM MICROELECTRONIC - MARIN SA EM3022 Very Low Power 8-Bit 32 khz RTC Module with Digital Trimming and High Level Integration Description The V3022 is a low power CMOS real time clock with a built in crystal. Standby current is typically 1.2 µa and the access time is 50 ns. The interface is 8 bits with multiplexed address and data. Multiplexing of address and data is handled by the input line A /D. There are no y flags in the V3022, internal time update cycles are invisible to the user's software. Time data can be read from the V3022 in 12 or 24 hour data formats. An external signal puts the V3022 in standby mode. Even in standby, the V3022 pulls the IRQ pin active low on an internal alarm interrupt. Calendar functions include leap year correction and week number calculation. Time precision can be achieved by digital trimming. Applications Industrial controllers Alarm systems with periodic wake up PABX and telephone systems Point of sale terminals Automotive electronics Features Built-in crystal with digital trimming and temperature compensation facilities 50 ns access time with 50 pf load capacitance Standby on power down typically 1.2 µa Wide voltage range, 2.0V to 5.5V Universal interface compatible with both Intel and Motorola Simple 8 bit interface with no delays or y flags Power fail input disables during power up / down of reset Bus can be in tri-state in power fail mode 12 or 24 hour data formats Time to 1/100 of a second Leap year correction and week number calculation Alarm and timer interrupts Programmable interrupts: 10 ms, 100 ms, s or min Sleep mode capability Alarm programmable up to one month Timer measures elapsed time up to 24 hours Temperature range: -40 C to +85 C Package SO28 Typical Operating Configuration Pin Assignment SO28 TEST PF AD0 AD1 NC AD2 AD3 A/D IRQ V3022 NC AD7 AD6 AD5 NC AD4 RD WR CS V SS V DD V SS V DD V SS V DD V SS V DD V SS V DD Fig. 2 Fig
2 Absolute Maximum Ratings Parameter Symbol Conditions Maximum voltage at VDD VDDmax VSS + 7.0V Maximum voltage at remaining pins Vmax VDD + 0.3V Min. voltage on all pins Vmin VSS 0.3V Maximum storage temperature TSTOmax +85 C Minimum storage temperature TSTOmin -55 C Maximum electrostatic discharge to MIL-STD-883C method with ref. to VSS VSmax 1000V Maximum soldering conditions TSmax 260 C x 10s Shock resistance 5000 g. 0.3ms, ½ sine Table 1 Stresses above these listed maximum ratings may cause permanent damages to the device. Exposure beyond specified operating conditions may affect device reliability or cause malfunction. Handling Procedures This device has built-in protection against high static voltages or electric fields; however, anti-static precautions must be taken as for any other CMOS component. Unless otherwise specified, proper operation can only occur when all terminal voltages are kept within the voltage range. Unused inputs must always be tied to a defined logic voltage level. Operating Conditions Parameter Symbol Min Typ Max Unit Operating temperature T A C Logic supply voltage V DD V Supply voltage dv/dt (power-up & down) dv/dt 6 V/µs (note 1) Decoupling capacitor 100 nf Table 2 Electrical Characteristics VDD= 5.0V ±10%, VSS = 0V, TA=-40 to +85 C, unless otherwise specified Parameter Symbol Test Conditions Min Typ Max Unit Standby current (note 2) IDD VDD = 3 V, PF = 0 PF = 0 Dynamic current (note 3) IDD CS = 4 MHz, RD = VSS WR = VDD µa µa 1.5 ma IRQ (open drain) Output low voltage VOL IOL = 8 ma 0.4 V Output low voltage VOL IOL = 1 ma, VDD = 2 V 0.4 V Inputs and Outputs Input logic low VIL TA = +25 C 0.2 VDD V Input logic high VIH TA = +25 C 0.8 VDD V Output logic low VOL IOL = 6 ma 0.4 V Output logic high VOH IOH = 6 ma 2.4 V PF activation voltage VPFL 0.5 VDD V PF hysteresis VH 100 mv Input leakage IIN VSS < VIN < VDD na Output tri-state leakage ITS CS = na Oscillator Characteristics Starting voltage VSTA TA +25 C 2 V VSTA 2.5 V Start-up time TSTA 1 s Frequency Characteristics Frequency tolerance f/f TA = +25 C addr. 10 hex = 00 hex ppm (note 4) Frequency stability fsta 2.0 VDD 5.5 V (note 5) 1 5 ppm/v Temperature stability tsta addr. 10 hex = 00 hex see Fig.5 ppm Aging tag TA = +25 C, first year ±5 ppm/year Table 3 Note 1: For temperature below -20 C, dv/dt max 0.1V/ms. Note 2: With PFO = 0 (VSS) all pads can be tri-state, tested. With PFO = 1 (VDD), CS = 1 (VDD) and all other pads fixed to VDD or VSS: same standby current, not tested. Note 3: All other inputs to VDD and all outputs open. Note 4: See Fig. 4 Note 5: At a given temperature. 2
3 Typical Standby Current at VDD = 5 V Fig. 3 Typical Frequency on IRQ Fig. 4 Module Characteristic F F O = ppm 2 C (T TO) 2 ± 10% F/FO = the ratio of the change in frequency to the nominal value expressed in ppm (it can be thought of as the frequency deviation at any temperature) T = the temperature of interest in C TO = the turnover temperature (25 ± 5 C) To determine the clock error (accuracy) at a given temperature, add the frequency tolerance at 25 C to the value obtained from the formula above. Fig
4 Timing Characteristics (standard temperature range) VDD= 5.0 ±10%, VSS = 0V and TA=-40 to +85 C Parameter Symbol Test Conditions Min. Typ. Max. Unit Chip select duration, write cycle tcs 50 ns Write pulse duration twr 50 ns Time between two transfers tw 100 ns RAM access time (note 1) tacc CLOAD = 50pF ns Data valid to Hi-impedance (note 2) tdf ns Write data settle time (note 3) tdw 50 ns Data hold time (note 4) tdh 10 ns Advance write time tadw 10 ns PF response delay tpf 100 ns Rise time (all timing waveform signals) Fall time (all timing waveform signals) tr 200 ns tf 200 ns CS delay after A /D (note 5) t A /Ds 5 ns CS delay to A /D t A /Dt 10 ns Note 1: tacc starts from RD, ( DS ) or CS, whichever activates last Typically, tacc = CEXT in ns; where CEXT (external parasitic capacitance) is in pf Note 2: tdf starts from RD ( DS ) or CS, whichever deactivates first Note 3: tdw ends at WR (R/ W ) or CS, whichever deactivates first Note 4: tdh starts from WR (R/ W ) or CS, whichever deactivates first Note 5: A /D must come before a CS and RD or a CS and WR combination. The user has to guarantee this. Table 4 Timing Waveforms Read Timing for Intel ( RD and WR Pulse) and Motorola ( DS or RD pin tied to CS and R/ W ) Fig. 6a 4
5 Intel Interface Write Timing Fig. 6b Write Fig. 6c Read Fig. 6d 5
6 Motorola Interface Motorola Write Fig. 6e Write Fig. 6f Read Fig. 6g 6
7 General Block Diagram Fig
8 Pin Description SO28 Package Pin Name Description 1 TEST Do not connect, factory test pin I 2 PF Power fail I 3 AD0 Bit 0 from MUX address / data 4 AD1 Bit 1 from MUX address / data 5 NC No connection - 6 AD2 Bit 2 from MUX address / data 7 AD3 Bit 3 from MUX address / data 8 A /D Address / data decode I 9 IRQ Interrupt request O VSS Supply ground (substrate) GND VDD Positive supply terminal PWR 20 CS Chip select I 21 WR WR (Intel) or R/ W (Motorola) I 22 RD RD (Intel) or DS (Motorola) I 23 AD4 Bit 4 from MUX address / data 24 NC No connection - 25 AD5 Bit 5 from MUX address / data 26 AD6 Bit 6 from MUX address / data 27 AD7 Bit 7 from MUX address / data 28 NC No connection - Table 5 Functional Description Data Retention and Standby The V3022 is put in standby mode by activating the PF input. When pulled logic low, PF will disable the input lines, and immediately take to high impedance the lines AD 0-7. Input states must be under control whenever PF is deactivated. If no specific power fail signal can be provided, PF can be tied to the system RESET. Even in standby the interrupt request pin IRQ will pull to ground upon an unmasked alarm interrupt occurring. Initialisation When power is first applied to the V3022 all registers have a random value. To initialise the V3022, software must first write a 1 to the initialisation bit (addr. 2 bit 4) and then a 0. This sets the Frequency Tuning bit and clears all other status bits. The time and date parameters should then be loaded into the RAM (addr. 20 to 28 hex) and then transferred to the reserved clock area using the clock command followed by a write. The digital trimming register must then be initialised by writing 210 (D2 hex) to it, if Frequency Tuning is not required. After having written a value to the digital trimming register the frequency tuning mode bit can be cleared. RAM Configuration The RAM area of the V3022 has a reserved clock and time area, a data space, and an address command space (see Table 9 or Fig. 7). The reserved clock and timer area is not directly accessible to the user, it is used for internal time keeping and contains the current time and date plus the timer parameters. Data Space All locations in the data space are Read/Write. The data space is directly accessible to the user and is divided into five areas: Status Registers three registers used for status and control data for the device (see Table 6, 7 and 8). Digital Trimming Register a special function described under "Frequency Tuning". Time and Date Registers nine time and date locations which are loaded with, either the current time and date parameters from the reserved clock area or the time and date parameters to be transferred to the reserved clock area. Alarm Registers five locations used for setting the alarm parameters. Timer Registers four locations which are loaded with either the timer parameters from the reserved timer area or the timer parameters to be transferred to the reserved timer area. 8
9 Status Words Status 0 - Address 00 Hex Read / Write bits 0 - disabled / 24 hour 1 - enabled / 12 hour frequency tuning mode pulse enable / disable alarm enable / disable timer enable / disable 24 hour / 12 hour (note 1) time set lock test bit 0 test bit 1 Note 1: The alarm hours, address 33 hex. must always be rewritten after a change between 12 and 24 hour formats Status 1 - Address 01 Hex Read / Write bits Status 2 - Address 02 Hex Read / Write bits 0 - masked / no event 1 - unmasked / event pulse mask alarm mask timer mask reserved pulse flag alarm flag timer flag reserved 0 - masked / no event 1 - unmasked / event pulse every 10 ms pulse every 100 ms pulse every second pulse every minute initialisation bit reserved reserved reserved Table 6 Table 7 Table 8 EM3022 RAM Map Address Parameter Range Dec Hex Data Space Status status status status 2 Special purpose digital trimming Clock /100 second Seconds Minutes hours (note 1) Date Month Year week day week number Alarm /100 second Seconds minutes hours (note 1 & 2) Date Timer /100 second Seconds Minutes Hours Address Command Space 240 F0 clock and timer transfer 241 F1 clock transfer 242 F2 timer transfer Table 9 Note 1: The MSB (bit 7) of the hours byte (addr. 23 hex for the clock and 33 hex for the alarm) are used as AM/PM indicators in the 12 hour time data format and reading of the hours byte must be preceded by masking of the AM/PM bit. A set AM/PM bit indicates PM. In the 24 hour time data format the bit will always be zero. Note 2: The alarm hours, addr. 33 hex, must always be rewritten after a change between 12 and 24 hour modes. Address Command Space This space contains the three commands used for carrying out the transfers between the Time and Data Register and / or the Timer Registers and the reserved clock and timer area. Communication Data transfer is in 8 bit parallel form. All time data is in packed BCD format with tens data on lines AD7-4 and units on lines AD3-0. To access information within the RAM (see Fig.7) first write the RAM address, then read or write from or to this location. Fig.8 shows the two steps needed. The lines AD0-7 will be treated as an address when pin A /D is low, and as data when A /D is high. Pin A /D must not change state during any single read or write access. One line of the address (e.g. A0) can be used to implement the A /D signal (see "Typical Operating Configuration", Fig.1). Until a new address is written, data accesses (/D high) will always be to the same RAM address. 9
10 Communication Sequence A/D 0 A/D 1 Write RAM address to the V3022 Read or write data from or to the above address Fig. 8 Access Considerations The communication sequence shown in Fig.8 is reentrant. When the address is written to the V3022 (ie. first step of the communication sequence) it is stored in an internal address latch. Software can read the internal address latch at any time by holding the /D line low during a read from the V3022. So, for example, an interrupt routine can read the address latch and push it on to a stack, popping it when finished to restore the V3022. N.B. Alarm and timer interrupt routines can reprogram the alarm and timer without it being necessary to read or reprogram the clock. Commands The commands allow software to transfer the clock and timer parameters in a sequence (eg. seconds, minutes, hours, etc.) without any danger of an internal time update with carry over corrupting the data. They also avoid delaying internal time updates while using the V3022, as updates occurring in the reserved clock and timer area are invisible to software. Software writes or reads parameters to or from the RAM only. There are three commands that occupy the command address space in the RAM. The function of these commands is to transfer data from the reserved clock and timer area to the RAM or to transfer data in the opposite direction, from the RAM to the reserved clock and timer area. The commands take place in two steps as do all other communications. The command address is sent with A /D low. This is followed by either a read ( RD ) or a write ( WR ), with A /D high, to determine the direction of the transfer. If the second step is a read then the data is transferred from the reserved clock and timer area to the RAM and if the second step is a write then the data that has already been loaded into the RAM clock and/or timer locations is transferred to the reserved clock and/or timer area. Clock and Calendar The time and date locations in RAM (see Table 9) provide access to the 1/100 seconds, seconds, minutes, hours, date, month, year, week day and week number. These parameters have the ranges indicated in Table 9. The V3022 may be programmed for 12 or 24 hour time format (see section "12/24 Data Format"). If a parameter is found to be out of range, it will be cleared when the units value on its being next incremented is equal to or greater than 9 eg. B2 will be set to 00 after the units have incremented to 9 (ie. B9 to 00). The device incorporates leap year correction and week number calculation at the beginning of a year. If the first day of the year is day 05, 06 or 07 of the week, then it is given a zero week number, otherwise it becomes week 1. Week days are numbered from 1 to 7 with Monday as day 1. Reading of the current time and date must be preceded by a clock command. The time and date from the last clock command is held unchanged in RAM. When transferring data to the reserved clock and timer area remember to clear the time set lock bit first. Timer The timer can be used either for counting elapsed time, or for giving an interrupt (IRQ ) on being incremented from 23:59:59:99 to 00:00:00:00. The timer counts up with a resolution of 1/100 second in the timer reserved areas. The timer enable/disable bit (addr. 00 hex, bit 3) must be set by software to allow the timer to be incremented. The timer is incremented in the reserved timer area, every internal time update (10 ms). The timer flag (addr. 01 hex, bit 6) is set when the timer rolls over from 23:59:59:99 to 00:00:00:00 and the IRQ becomes active if the timer mask bit (addr. 01, bit 2) is set. The IRQ will remain active until software acknowledges the interrupt by clearing the timer flag. The timer is incremented in the standby mode, however it will not cause IRQ to become active until power (VDD) has been restored. Note: The user should ensure that a time lapse of at least 60 microseconds exists between the falling edge of the IRQ and the clearing of the timer flag. 10
11 Reading the Clock Setting the Timer (Time Set Lock Bit = 0) [Pin 7 = A/D] Start [Pin 7 = A/D] Start Write clock command (addr. F1 hex) to the V3022 Write 1/100 sec. address (40 hex) to the V3022 Read data from the V3022 to copy the timer parameters from the reserved clock area to the RAM. A data read has no significance Write 1/100 sec. data to the RAM Write sec. address (41 hex) to the V3022 Write 1/100 sec. address (20 hex) to the V3022 Write sec. data to the RAM Read 1/100 sec. data from the RAM Write min. address (42 hex) to the V3022 Write sec. address (21 hex) to the V3022 Write min. data to the RAM Read sec. data from the RAM Write hours address (43 hex) to the V3022 Write min. address (22 hex) to the V3022 Write hours data to the RAM Read min. data from the RAM Write timer command (addr. F2 hex) to the V3022 End Fig. 9 Write F2 hex to the V3022 to copy the timer parameters from RAM to the reversed timer area End Fig. 10 Note: Commands are only valid as commands when the A /D line is low. Writing F2 hex with the A /D line high, as in the last box of Fig. 8, serves only to activate the V3022 write pin which determines the direction of transfer. Alarm An alarm date and time may be preset in RAM addresses 30 to 34 hex. The alarm function can be activated by setting the alarm enable / disable bit (addr. 00 hex, bit 2). Once enabled the preset alarm time and date are compared, every internal time update cycle (10 ms), with the clock parameters in the reserved clock area. When the clock parameters equal the alarm parameters the alarm flag (addr. 01 hex, bit 5) is set. If the alarm mask bit (addr. 01 hex, bit 1) is set, the IRQ pin goes active. The alarm flag indicates to software the source of the interrupt. IRQ will remain active until software acknowledges the interrupt by clearing the alarm flag. If the alarm is enabled, and an alarm address set to FF hex, this parameters is not compared with the associated clock parameter. Thus it is possible to achieve a repeat feature where an alarm occurs every programmed number of seconds, or seconds and minutes, or seconds, minutes and hours. The V3022 pulls the open drain IRQ line active low during standby when an alarm interrupt occurs. If the 12/24 hour mode is changed then the alarm hours must be re-initialised. Note: The user should ensure that a time lapse of at least 60 microseconds exists between the falling edge of the IRQ and the clearing of the alarm flag. 11
12 IRQ The IRQ output is used by 4 of the V3022's features. These are: 1. Pulse, to provide periodic interrupts to the microprocessors at pre-programmed intervals; 2. Alarm to provide an interrupt to the microprocessor at a pre-programmed time and date; 3. Timer, to provide an interrupt to the microprocessor when the time rolls over from 23:59:59:99 to 00:00:00:00; and 4. Frequency trimming (see section "Frequency Trimming"). The first 3 features listed are similar in the way they provide interrupts to the microprocessor. Each o the 3 has an enable / disable bit, a flag bit, and an interrupt mask bit. The enable / disable bit allows software to select a feature or not. A set flag bit indicates that an enable feature has reached its interrupt condition. Software must clear the flag bit. The interrupt mask bit allows or disallows the IRQ output to become active when the flag bit is se. The IRQ output becomes active whenever any interrupt flag is set which also has its mask bit set. For all sources of maskable interrupts within the V3022, the IRQ output will remain active until software clears the interrupt flag. The IRQ output is the logical OR of all the unmasked interrupt flags. The IRQ output is open drain so an external pullup to VDD is needed. In standby ( PF active) the IRQ output will be active if the alarm mask bit (addr, 01 hex, bit 1) is set and the alarm flag is also set. The timer or the pulse feature cannot cause the IRQ output to become active while in standby. Pulse There are 4 programmable pulse frequencies available on the V3022, these are every 10 ms, 100 ms, second or minute. The pulse feature is activated by setting the pulse enable / disable bit at address 00, bit 1. The pulse frequency is selected by setting one of the bit 0 to 3 at address 02 hex (see Table 8). If more than one of the pulse bits is set then the feature is disabled. At the selected interval the pulse flag bit (addr. 01 hex, bit 4) is set. If the pulse mask bit (addr. 01 hex, bit 0) is set then the IRQ pin goes active. The pulse flag indicates to software the source of the interrupt. IRQ will remain active until software acknowledges the interrupt by clearing the pulse flag. The pulse feature is disabled while in standby. Upon power restoration the pulse feature is enabled if enabled prior to standby. See also the section "Frequency Tuning". Note: The user should ensure that a time lapse of at least 60 microseconds exists between the falling edge of the IRQ and the clearing of the pulse flag. Time Set Lock The time set lock control bit is located at address 00 hex, bit 5 (see Table 6). When set by software, this bit disables any transfer from the RAM to the reserved clock and timer area as well as inhibiting any write to the digital trimming register at address 10 hex. When the time set lock bit is set the following transfer operations are disabled: The clock command followed by write, the timer command followed by write, the clock and timer command followed by write, and writing to the digital trimming register A set bit prevents unauthorized overwriting of the reserved clock and timer area. Reading of the reserved clock and timer area, using the commands, is not affected by the time set lock bit. Clearing the time set lock bit by software will re-enable the above listed commands. On initialisation the time set lock bit is cleared. Frequency Tuning The V3022 offers a key feature called "Digital Trimming", which is used for the clock accuracy adjustment. Unlike the traditional capacitor trimming method which tunes the crystal oscillator, the digital trimming acts on the divider chain, allowing the clock adjustment by software. The oscillator frequency itself is not affected. The Principle of Digital Trimming With the digital trimming disabled (ie. digital trimming register set to 00 hex), the oscillator and the first stages of the divider chain will run slightly too fast (typ. 210 ppm: ppm = parts per million), and will generate a 100 Hz signal with a frequency of typically Hz. To correct this frequency, the digital trimming logic will inhibit every 31 seconds, a number of clock pulses, as set in the digital trimming register. Since the duration of 31 seconds corresponds to 1'015'808 oscillator cycles, the digital trimming has a resolution of ppm. In other words every increment by 1 of the digital trimming value will slow down the clock by ppm, which permits the accuracy of ± 0.5 ppm to be reached. Note that a 1 ppm error will result in a 1 second difference after 11.5 days, or a 1 minute difference after 694 days! The trimming range of the V3022 is from 0 to 251 ppm. The 251 ppm correction is obtained by writing 255 (FF hex) into the digital trimming register. 12
13 How to Determine the Digital Trimming Value The value to write into the digital trimming register has to be determined by the following procedure: 1. Initialise the V3022 by writing a 1 and then a 0 into the "Initialisation Bit" of the status register 2 (addr. 02 hex, bit 4). This activates the frequency tuning mode in status register 0 (addr. 00 hex, bit 1) and clears the other status bits. 2. Write the value 00 hex into the digital trimming register (addr 10 hex). From now, the IRQ output (open drain) will deliver the 100 Hz signal, which has a 20% duty cycle. 3. Measure the duration of 21 pulses at the IRQ output, with the trigger set for the falling edge. It is possible also to divide the IRQ frequency by 21, using a TTL or CMOS external circuit. 4. Compute the frequency error in ppm: 210ms measured valueinms freq. error = x ms 6 5. Compute the corrective value to write into the digital trimming register. Digital trimming value = frequency error / Write this value into the digital trimming register. 7. Switch off the frequency tuning mode in status 0 (addr. 00 hex, bit 0 set to 0). The Real Time Clock circuit will now run accurately at an operating temperature equal to the calibration temperature. If the operating temperature differs from the one at calibration time, the graphs shown on Fig. 4 and 5 will help in determining the definitive value. If the mean operating temperature of the equipment is not known at calibration time, the equipment user will do the final correction with a software provided by the system designer. To avoid the calibration procedure, it is possible also to set the digital trimming register to 210 (D2 hex) as a standard starting value, and let the final equipment user perform the final adjustment on site, which will take the real temperature into account. Time Correction at Room Temperature Let us consider that the duration of 21 pulses of the IRQ signal is ms at room temperature. The frequency error is: ( ) / 210 x 10 6 = ppm The value for the digital trimming register is: / = , rounded to 194 (C2 hex) Time Correction with Change of Temperature If the mean temperature on site is known to be 45 C, the frequency error determined at room temperature has to be modified using the graphs or the equation of Fig / 24 Hour Data Format The V3022 can run in 12 hour data format. On initialisation the 12/24 hour bit addr. 00 bit 4 is cleared putting the V3022 in 24 hour data format. If the 12 hour data format is required then bit 4 at addr. 00 must be set. In the 12 hour data format the AM/PM indicator is the MSB of the hours register addr. 23 bit 7. A set bit indicates PM. When reading the hours in the 12 hour data format software should mask the MSB of the hours register. In the 24 hour data format the MSB is always zero. The internal clock registers change automatically between 12 and 24 hour mode when the 24/12 hour bit is changed. The alarm hours however must be rewritten. Test From the various test features added to the V3022 some may be activated by the user. Table 6 shows the test bits. Table 10 shows the three available modes and how they may be activated. The first accelerates the incrementing of the parameters in the reserved clock and timer area by 32. The second causes all clock and timer parameters, in the reserved clock and timer area, to be incremented in parallel at 100 Hz with no carry over, ie. independently of each other. The third test mode combines the previous two resulting in parallel incrementing at 3.2 khz. While test bit 1 is set (addr. 00 hex, bit 7) the digital trimming action is disabled and no pulses are removed from the divider chain. Test bit 0 (addr. 00 hex, bit 6) can be combined with digital trimming (see section "Frequency Tuning"). To leave test, the test bits (addr 00 hex, bits 6 and 7) must be cleared by software. Test corrupts the clock and timer parameters and so all parameters should be re-initialised after a test session. Test Modes Addr. Addr. 00hex bit 7 00hex bit 6 Function 0 0 Normal operation 0 1 Acceleration by Parallel increment of all clock and timer parameters at 100 Hz with no carry over; dependent on the status of bit 3 at address 00 hex 1 1 Parallel increment of all clock and timer parameters at 3.2 khz with no carry over; dependent on the status of bit 3 at address 00 hex Table 10 f/f = x (45-25) 2 = ppm The trimming value for 45 C will be: ( ppm 14.0 ppm) / = ppm, rounded to 179 (B3 hex) 13
14 Battery or Supercap Connection V DD Note: The diodes must have a forward voltage drop of less than 0.3V. BAT 85 s are recommended. Power fail (low for standby) PF V DD V Battery or + Supercap V SS V SS Fig. 11 Typical Applications V3022 Interfaced with Intel CPU ( RD and WR pulse) Fig. 12 V3022 Interfaced with Motorola CPU ( DS or RD pin tied to CS, and R/ W ) Fig
15 Process Application Solenoid valve Controller Temperature sensor The formula in Fig. 4 is used by software to continually update the digital trimming register and so compensate the V3022 for the ambient temperature. The timer is used to measure the duration the valve is on. The alarm feature is used to turn the controller power on and off at the time programmed by software. The V3022 pulls IRQ active low on an alarm even in standby and thus can control the power on/off switch for the controller. Fig. 14 Ordering and Package Information Dimensions of 28-pin SOIC Package Fig. 15 Ordering Information When ordering, please specify the complete part number. Part Number Package Delivery Form Package Marking (first line) V3022SO28B+ 28-pin SOIC Tape & Reel V S V3022SO28A+ 28-pin SOIC Stick V S EM Microelectronic-Marin SA ( EM ) makes no warranties for the use of EM products, other than those expressly contained in EM's applicable General Terms of Sale, located at EM assumes no responsibility for any errors which may have crept into this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property rights of EM are granted in connection with the sale of EM products, neither expressly nor implicitly. In respect of the intended use of EM products by customer, customer is solely responsible for observing existing patents and other intellectual property rights of third parties and for obtaining, as the case may be, the necessary licenses. Important note: The use of EM products as components in medical devices and/or medical applications, including but not limited to, safety and life supporting systems, where malfunction of such EM products might result in damage to and/or injury or death of persons is expressly prohibited, as EM products are neither destined nor qualified for use as components in such medical devices and/or medical applications. The prohibited use of EM products in such medical devices and/or medical applications is exclusively at the risk of the customer 15
V3021 EM MICROELECTRONIC - MARIN SA. Ultra Low Power 1-Bit 32 khz RTC. Description. Features. Applications. Typical Operating Configuration
EM MICROELECTRONIC - MARIN SA Ultra Low Power 1-Bit 32 khz RTC Description The is a low power CMOS real time clock. Data is transmitted serially as 4 address bits and 8 data bits, over one line of a standard
Ultra Low Power 1-Bit 32 khz RTC
查询 SO8A 供应商 捷多邦, 专业 PCB 打样工厂,24 小时加急出货 R EM MICROELECTRONIC - MARIN SA Ultra Low Power 1-Bit 32 khz RTC Description The is a low power CMOS real time clock. Data is transmitted serially as 4 address bits
Low Power Windowed Watchdog with Reset, Sleep Mode Functions. Features. Applications. Selection Table. Part Number V REF
EM MICROELECTRONIC - MARIN SA Low Power Windowed Watchdog with Reset, Sleep Mode Functions Description The offers a high level of integration by combining voltage monitoring and software monitoring using
Reset Circuit with Adjustable Delay
EM MICROELECTRONIC - MARIN SA Reset Circuit with Adjustable Delay Description The is an ultra-low current reset circuit available in a large variety of configurations and very small packages for maximum
Extremely Accurate Power Surveillance, Software Monitoring and Sleep Mode Detection. Pin Assignment. Fig. 1
EM MICOELECTONIC - MAIN SA Extremely Accurate Power Surveillance, Software Monitoring and Sleep Mode Detection Description The offers a high level of integration by voltage monitoring and software monitoring
5V Automotive Regulator with Windowed Watchdog. Features. Applications. Selection Table. Part Number V REF
EM MICOELECTONIC - MAIN SA 5V Automotive egulator with Windowed Watchdog Description The offers a high level of integration by combining voltage regulation, voltage monitoring and software monitoring using
78A207 MFR1 Receiver DATA SHEET DESCRIPTION FEATURES OCTOBER 2005
DESCRIPTION The 78A207 is a single-chip, Multi-Frequency (MF) receiver that can detect all 15 tone-pairs, including ST and KP framing tones. This receiver is intended for use in equal access applications
DS1202, DS1202S. Serial Timekeeping Chip FEATURES PIN ASSIGNMENT. ORDERING INFORMATION DS pin DIP DS1202S 16 pin SOIC DS1202S8 8 pin SOIC
DS22, DS22S Serial Timekeeping Chip FEATURES Real time clock counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap year compensation 2 x 8 RAM for scratchpad data
Programmable Clock Generator
Features Clock outputs ranging from 391 khz to 100 MHz (TTL levels) or 90 MHz (CMOS levels) 2-wire serial interface facilitates programmable output frequency Phase-Locked Loop oscillator input derived
MM58174A Microprocessor-Compatible Real-Time Clock
MM58174A Microprocessor-Compatible Real-Time Clock General Description The MM58174A is a low-threshold metal-gate CMOS circuit that functions as a real-time clock and calendar in bus-oriented microprocessor
Parameters Symbol Min. Typ. Max. Unit Condition Frequency Range Output Frequency Range f MHz
Features Any frequency between 1 MHz and 110 MHz accurate to 6 decimal places Operating temperature from -40 C to +85 C. Refer to MO2018 for -40 C to +85 C option and MO2020 for -55 C to +125 C option
A6250 High Efficiency Linear Power Supply with Accurate Power Surveillance and Software Monitoring Features Applications
EM MICROELECTRONIC-MARIN SA A6250 High Efficiency Linear Power Supply with Accurate Power Surveillance and Software Monitoring Features Highly accurate 5 V, 250 ma guaranteed output Low dropout voltage,
SiT9003 Low Power Spread Spectrum Oscillator
Features Frequency range from 1 MHz to 110 MHz LVCMOS/LVTTL compatible output Standby current as low as 0.4 µa Fast resume time of 3 ms (Typ)
Xicor Real Time Clock Family Users Guide. New Devices Integrate Crystal Compensation Circuitry AN of 8.
Xicor Real Time Clock Family Users Guide New Devices Integrate Crystal Compensation Circuitry 1 of 8 Overall Functionality Xicor Real Time Clock (RTC) products integrate the real time clock function with
Low-Current Consumption, Real-Time Clock IC (General-Purpose IC)
S1T542XXD0A00 Low-Current Consumption, Real-Time Clock IC (General-Purpose IC) Operating power voltage 1.6 to 5.5V (-40 to +85 C) Output control 32.768kHz output function Clock power voltage 1.2 to 5.5V
Parameters Symbol Min. Typ. Max. Unit Condition Frequency Range. Frequency Stability and Aging ppm ppm ppm ppm
Features Frequencies between 115.194001 MHz to 137 MHz accurate to 6 decimal places Operating temperature from -40 C to +125 C. For -55 C option, refer to MO8920 and MO8921 Supply voltage of +1.8V or +2.5V
ICS502 LOCO PLL CLOCK MULTIPLIER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS502 Description The ICS502 LOCO TM is the most cost effective way to generate a high-quality, high-frequency clock output and a reference from a lower frequency crystal or clock input. The
ICS511 LOCO PLL CLOCK MULTIPLIER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS511 Description The ICS511 LOCO TM is the most cost effective way to generate a high quality, high frequency clock output from a lower frequency crystal or clock input. The name LOCO stands
ULTRA-LOW VOLTAGE DCDC BOOST CONVERTER FOR THERMAL ELECTRICAL GENERATORS
AVSS0 AVSS1 AVSS2 DIS VSUP LX0 LX1 LX2 FB AC EM MICROELECTRONIC - MARIN SA DATASHEET Ɩ EM8900 ULTRA-LOW VOLTAGE DCDC BOOST CONVERTER FOR THERMAL ELECTRICAL GENERATORS EM8900 EM8900 EM8502 Wake-up timers
LSI/CSI LS7560N LS7561N BRUSHLESS DC MOTOR CONTROLLER
LSI/CSI LS7560N LS7561N LSI Computer Systems, Inc. 15 Walt Whitman Road, Melville, NY 747 (631) 71-0400 FAX (631) 71-0405 UL A3800 BRUSHLESS DC MOTOR CONTROLLER April 01 FEATURES Open loop motor control
SERIALLY PROGRAMMABLE CLOCK SOURCE. Features
DATASHEET ICS307-02 Description The ICS307-02 is a versatile serially programmable clock source which takes up very little board space. It can generate any frequency from 6 to 200 MHz and have a second
DS1307ZN. 64 X 8 Serial Real Time Clock PIN ASSIGNMENT FEATURES
DS1307 64 8 Serial Real Time Clock FEATURES Real time clock counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap year compensation valid up to 2100 56 byte nonvolatile
Oscillator fail detect - 12-hour Time display 24-hour 2 Time Century bit - Time count chain enable/disable -
Features Description Using external 32.768kHz quartz crystal Real-time clock (RTC) counts seconds, minutes hours, date of the month, month, day of the week, and year with leap-year compensation valid up
LOCO PLL CLOCK MULTIPLIER. Features
DATASHEET ICS501A Description The ICS501A LOCO TM is the most cost effective way to generate a high quality, high frequency clock output from a lower frequency crystal or clock input. The name LOCO stands
DS1642 Nonvolatile Timekeeping RAM
www.dalsemi.com Nonvolatile Timekeeping RAM FEATURES Integrated NV SRAM, real time clock, crystal, power fail control circuit and lithium energy source Standard JEDEC bytewide 2K x 8 static RAM pinout
DS1307ZN. 64 X 8 Serial Real Time Clock
64 X 8 Serial Real Time Clock www.dalsemi.com FEATURES Real time clock counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap year compensation valid up to 2100 56
Real-Time Clock (RTC) Module. Calendar in day of the week, day of the month, months, and years with automatic leap-year adjustment
Features Direct clock/calendar replacement for IBM AT-compatible computers and other applications Functionally compatible with the DS1287/DS1287A and MC146818A 114 bytes of general nonvolatile storage
4 x 10 bit Free Run A/D 4 x Hi Comparator 4 x Low Comparator IRQ on Compare MX839. C-BUS Interface & Control Logic
DATA BULLETIN MX839 Digitally Controlled Analog I/O Processor PRELIMINARY INFORMATION Features x 4 input intelligent 10 bit A/D monitoring subsystem 4 High and 4 Low Comparators External IRQ Generator
ICS512 LOCO PLL CLOCK MULTIPLIER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS512 Description The ICS512 is the most cost effective way to generate a high-quality, high frequency clock output and a reference clock from a lower frequency crystal or clock input. The name
U2270B replacement by EM4095 reader chip
EM MICROELECTRONIC - MARIN SA 604005 Title: Product Family: Part Number: Keywords: Application Note 604005 U2270B replacement by reader chip RFID U2270B LF Reader modification Date: October 26, 2012 1.
PATENTED. PAT No. : HT1622/HT1622G RAM Mapping 32 8 LCD Controller for I/O MCU. Features. General Description.
RAM Mapping 328 LCD Controller for I/O MCU PATENTED PAT No. : 099352 Features Operating voltage: 2.7V~5.2V Built-in RC oscillator 1/4 bias, 1/8 duty, frame frequency is 64Hz Max. 328 patterns, 8 commons,
Built-in LCD display RAM Built-in RC oscillator
PAT No. : TW 099352 RAM Mapping 488 LCD Controller for I/O MCU Technical Document Application Note Features Operating voltage: 2.7V~5.2V Built-in LCD display RAM Built-in RC oscillator R/W address auto
css Custom Silicon Solutions, Inc.
css Custom Silicon Solutions, Inc. GENERAL PART DESCRIPTION The is a micropower version of the popular timer IC. It features an operating current under µa and a minimum supply voltage of., making it ideal
R/W address auto increment External Crystal kHz oscillator
RAM Mapping 328 LCD Controller for I/O MCU PATENTED PAT No. : 099352 Features Operating voltage: 2.7V~5.2V R/W address auto increment External Crystal 32.768kHz oscillator Two selectable buzzer frequencies
Parameters Symbol Min. Typ. Max. Unit Condition Frequency Range Output Frequency Range f MHz
Features Any frequency between 1 MHz and 110 MHz accurate to 6 decimal places 100% pin-to-pin drop-in replacement to quartz-based XO Excellent total frequency stability as low as ±20 ppm Operating temperature
FX623 FX623. CML Semiconductor Products PRODUCT INFORMATION. Call Progress Tone Decoder
CML Semiconductor Products PRODUCT INFORMATION FX623 Call Progress Tone Decoder Features Measures Call Progress Tone Frequencies [ Busy, Dial, Fax-Tone etc.] Telephone, PABX, Fax and Dial-Up Modem Applications
RayStar Microelectronics Technology Inc. Ver: 1.4
Features Description Product Datasheet Using external 32.768kHz quartz crystal Supports I 2 C-Bus's high speed mode (400 khz) The serial real-time clock is a low-power clock/calendar with a programmable
PT7C43190 Real-time Clock Module
PT7C43190 Real-time Clock Module Features Description Low current consumption: 0.3µA typ. (V DD =3.0V, T A = 25 C) Wide operating voltage range: 1.35 to 5.5 V Minimum time keeping operation voltage: 1.25
DS1307/DS X 8 Serial Real Time Clock
DS1307/DS1308 64 X 8 Serial Real Time Clock www.dalsemi.com FEATURES Real time clock counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap year compensation valid
LOW POWER PROGRAMMABLE OSCILLATOR
LOW POWER PROGRAMMABLE OSCILLATOR SERIES LPOP 115.0 137.0 MHz FEATURES + High Frequency Programmable Low Power Oscillator for Low Cost + Excellent long time reliability + Excellent total frequency stability
Dual Processor Supervisors with Watchdog ADM13305
Dual Processor Supervisors with Watchdog ADM335 FEATURES Dual supervisory circuits Supply voltage range of 2.7 V to 5.5 V Pretrimmed threshold options:.8 V, 2.5 V, 3.3 V, and 5 V Adjustable.6 V voltage
LOCO PLL CLOCK MULTIPLIER. Features
DATASHEET ICS501 Description The ICS501 LOCO TM is the most cost effective way to generate a high-quality, high-frequency clock output from a lower frequency crystal or clock input. The name LOCO stands
Revision No History Draft Date Remark. 10 Initial Revision History Insert Jul Final
128Kx8bit CMOS SRAM Document Title 128K x8 bit 5.0V Low Power CMOS slow SRAM Revision History Revision No History Draft Date Remark 10 Initial Revision History Insert Jul.14.2000 Final 11 Marking Information
S-35390A H Series FOR AUTOMOTIVE 105 C OPERATION 2-WIRE REAL-TIME CLOCK. Features. Packages. ABLIC Inc., Rev.2.
www.ablic.com FOR AUTOMOTIVE 15 C OPERATION 2-WIRE REAL-TIME CLOCK ABLIC Inc., 211-218 Rev.2.2_3 The is a 15C operation CMOS 2-wire real-time clock IC which operates with the very low current consumption
ICS Glitch-Free Clock Multiplexer
Description The ICS580-01 is a clock multiplexer (mux) designed to switch between 2 clock sources with no glitches or short pulses. The operation of the mux is controlled by an input pin but the part can
S-5814A Series : 2.5 C ( 30 C to 100 C) Ta = 30 C : V typ. Ta = 30 C : V typ. Ta = 100 C : V typ. 0.5% typ.
www.ablicinc.com CMOS TEMPERATURE SENSOR IC ABLIC Inc., 2006-2015 Rev.4.1_02 The is a family of high-precision temperature sensor ICs on a single chip with a linear output voltage for temperature changes.
NOT RECOMMENDED FOR NEW DESIGN. S-5855A Series PWM OUTPUT TEMPERATURE SENSOR IC. Features. Application. Packages.
www.ablicinc.com ABLIC Inc., 2010-2017 The, developed by CMOS technology, is a 1-wire PWM output temperature sensor IC of low current consumption that itself changes the duty ratio according to temperature.
S-5855A Series PWM OUTPUT TEMPERATURE SENSOR IC. Features. Application. Packages. ABLIC Inc., Rev.1.
www.ablicinc.com PWM OUTPUT TEMPERATURE SENSOR IC ABLIC Inc., 2010-2017 Rev.1.3_01 The, developed by CMOS technology, is a 1-wire PWM output temperature sensor IC of low current consumption that itself
S-5813A/5814A Series CMOS TEMPERATURE SENSOR IC. Rev.1.2_00. Features. Applications. Package. Seiko Instruments Inc. 1
The is a family of high-precision temperature sensor ICs on a single chip with a linear output voltage for temperature changes. Each chip is composed of a temperature sensor, a constant current circuit,
LOW POWER PROGRAMMABLE OSCILLATOR
LOW POWER PROGRAMMABLE OSCILLATOR SERIES LPOP 1.0 110.0 MHZ FEATURES + Low Power Programmable Oscillator for Low Cost + Excellent long time reliability + Frequency range of 1 MHz and 110 MHz accurate to
ICS722 LOW COST 27 MHZ 3.3 VOLT VCXO. Description. Features. Block Diagram DATASHEET
DATASHEET ICS722 Description The ICS722 is a low cost, low-jitter, high-performance 3.3 volt designed to replace expensive discrete s modules. The on-chip Voltage Controlled Crystal Oscillator accepts
14-Bit Registered Buffer PC2700-/PC3200-Compliant
14-Bit Registered Buffer PC2700-/PC3200-Compliant Features Differential Clock Inputs up to 280 MHz Supports LVTTL switching levels on the RESET pin Output drivers have controlled edge rates, so no external
ABLIC Inc., 2012 Rev.1.0_02
S-9xxxA Series www.ablicinc.com FOR AUTOMOTIVE 25 C OPERATION VOLTAGE DETECTOR BUILT-IN DELAY CIRCUIT (EXTERNAL DELAY TIME SETTING) ABLIC Inc., 22 Rev.._2 The S-9xxxA Series, developed by using CMOS technology,
PL XIN CLK XOUT VCON. Xtal Osc. Varicap. Low Phase Noise VCXO (17MHz to 36MHz) PIN CONFIGURATION FEATURES DESCRIPTION BLOCK DIAGRAM
FEATURES PIN CONFIGURATION VCXO output for the 17MHz to 36MHz range Low phase noise (-130dBc @ 10kHz offset at 35.328MHz) LVCMOS output with OE tri-state control 17 to 36MHz fundamental crystal input Integrated
HM K 8 High Speed CMOS SRAM. Description. Features. Interface MATRA MHS. Block Diagram
8K 8 High Speed CMOS SRAM Description The is a high speed CMOS static RAM organized as 8192x8 bits. It is manufactured using MHS high performance CMOS technology. Access times as fast as 15 ns are available
Low Power Multiclock Generator with VCXO AK8130AH
Low Power Multiclock Generator with VCXO Features 27MHz Crystal Input Four Frequency-Selectable Clock Outputs One 27MHz-Reference Output Selectable Clock out Frequencies: - 54.000,74.1758, 74.250MHz -
LSI/CSI LS7290 STEPPER MOTOR CONTROLLER. LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631)
LSI/CSI UL A800 FEATURES: LSI Computer Systems, Inc. 1 Walt Whitman Road, Melville, NY 114 (1) 1-0400 FAX (1) 1-040 STEPPER MOTOR CONTROLLER Controls Bipolar and Unipolar Motors Cost-effective replacement
S-35190A 3-WIRE REAL-TIME CLOCK. Features. Applications. Packages. ABLIC Inc., Rev.4.2_03
www.ablicinc.com 3-WIRE REAL-TIME CLOCK ABLIC Inc., 2004-2016 Rev.4.2_03 The is a CMOS 3-wire real-time clock IC which operates with the very low current consumption in the wide range of operation voltage.
ICS HIGH PERFORMANCE VCXO. Features. Description. Block Diagram DATASHEET
DATASHEET ICS3726-02 Description The ICS3726-02 is a low cost, low-jitter, high-performance designed to replace expensive discrete s modules. The ICS3726-02 offers a wid operating frequency range and high
HT162X HT1620 HT1621 HT1622 HT16220 HT1623 HT1625 HT1626 COM
RAM Mapping 328 LCD Controller for I/O MCU PATENTED PAT No. : 099352 Technical Document Application Note Features Operating voltage: 2.7V~5.2V Built-in RC oscillator 1/4 bias, 1/8 duty, frame frequency
S-8110C/8120C Series CMOS TEMPERATURE SENSOR IC. Features. Applications. Packages
www.ablic.com www.ablicinc.com CMOS TEMPERATURE SENSOR IC ABLIC Inc., 2002-2015 Rev.5.1_02 The is a family of high-precision temperature sensor ICs on a single chip with a linear output voltage for temperature
SRM2B256SLMX55/70/10
256K-BIT STATIC RAM Wide Temperature Range Extremely Low Standby Current Access Time 100ns (2.7V) 55ns (4.5V) 32,768 Words 8-Bit Asynchronous DESCRIPTION The SRM2B256SLMX is a low voltage operating 32,768
DS4000 Digitally Controlled TCXO
DS4000 Digitally Controlled TCXO www.maxim-ic.com GENERAL DESCRIPTION The DS4000 digitally controlled temperature-compensated crystal oscillator (DC-TCXO) features a digital temperature sensor, one fixed-frequency
MK2703 PLL AUDIO CLOCK SYNTHESIZER. Description. Features. Block Diagram DATASHEET
DATASHEET MK2703 Description The MK2703 is a low-cost, low-jitter, high-performance PLL clock synthesizer designed to replace oscillators and PLL circuits in set-top box and multimedia systems. Using IDT
±2.5 C ( 55 to +130 C) mv/ C Typ. Ta = 30 C: V Typ. Ta = +30 C: V Typ. Ta = +130 C: V Typ. ±0.4% Typ.
Rev.1.2_00 CMOS TEMPERATURE SENSOR IC The is a high-accuracy temperature sensor IC on a single chip, provides output voltage which is linear against the temperature change. Each chip consists of a temperature
Application Manual. AB-RTCMC kHz-B5ZE-S3 Real Time Clock/Calendar Module with I 2 C Interface
Application Manual AB-RTCMC-32.768kHz-B5ZE-S3 Real Time Clock/Calendar Module with I 2 C Interface _ Abracon Corporation (www.abracon.com) Page (1) of (55) CONTENTS 1.0 Overview... 4 2.0 General Description...
S-35190A 3-WIRE REAL-TIME CLOCK. Rev.2.4_00. Features. Applications. Package. Seiko Instruments Inc. 1
Rev.2.4_00 3-WIRE REAL-TIME CLOCK Features The is a CMOS 3-wire real-time clock IC which operates with the very low current consumption and in the wide range of operation voltage. The operation voltage
8-Bit A/D Converter AD673 REV. A FUNCTIONAL BLOCK DIAGRAM
a FEATURES Complete 8-Bit A/D Converter with Reference, Clock and Comparator 30 s Maximum Conversion Time Full 8- or 16-Bit Microprocessor Bus Interface Unipolar and Bipolar Inputs No Missing Codes Over
Output freq. (Fo) Output Load
Description The QT1123 Real-Time Clock provides a time/calendar function, a 32 byte static RAM, and a 3 wire Serial Peripheral Interface (SPI Bus). The part is designed for high temperature applications
HY62256A Series 32Kx8bit CMOS SRAM
32Kx8bit CMOS SRAM DESCRIPTION The HY62256A is a high-speed, low power and 32,786 x 8-bits CMOS Static Random Access Memory fabricated using Hyundai's high performance CMOS process technology. The HY62256A
ML4818 Phase Modulation/Soft Switching Controller
Phase Modulation/Soft Switching Controller www.fairchildsemi.com Features Full bridge phase modulation zero voltage switching circuit with programmable ZV transition times Constant frequency operation
MOSA ELECTRONICS. Features. Description. MS8870 DTMF Receiver
Features Complete DTMF receiver Low power consumption Adjustable guard time Central Office Quality CMOS, Single 5V operation Description O rdering Information : 18 PIN DIP PACKAGE The is a complete DTMF
Triple Processor Supervisors ADM13307
Triple Processor Supervisors ADM337 FEATURES Triple supervisory circuits Supply voltage range of 2. V to 5.5 V Pretrimmed threshold options:.8 V, 2.5 V, 3.3 V, and 5 V Adjustable.6 V and.25 V voltage references
OSC2 Selector Guide appears at end of data sheet. Maxim Integrated Products 1
9-3697; Rev 0; 4/05 3-Pin Silicon Oscillator General Description The is a silicon oscillator intended as a low-cost improvement to ceramic resonators, crystals, and crystal oscillator modules as the clock
MK SPREAD SPECTRUM MULTIPLIER CLOCK. Description. Features. Block Diagram DATASHEET
DATASHEET MK1714-01 Description The MK1714-01 is a low cost, high performance clock synthesizer with selectable multipliers and percentages of spread spectrum designed to generate high frequency clocks
MK SPREAD SPECTRUM MULTIPLIER CLOCK. Description. Features. Block Diagram DATASHEET
DATASHEET MK1714-02 Description The MK1714-02 is a low cost, high performance clock synthesizer with selectable multipliers and percentages of spread designed to generate high frequency clocks with low
LC75836WS-T/D. 1/4-Duty General-Purpose LCD Driver
1/4-Duty General-Purpose LCD Driver Overview The LC75836WS-T is 1/4-duty general-purpose microprocessor-controlled LCD driver that can be used in applications such as frequency display in products with
ICS PLL BUILDING BLOCK
Description The ICS673-01 is a low cost, high performance Phase Locked Loop (PLL) designed for clock synthesis and synchronization. Included on the chip are the phase detector, charge pump, Voltage Controlled
1.5 Ω On Resistance, ±15 V/12 V/±5 V, icmos, Dual SPDT Switch ADG1436
Data Sheet.5 Ω On Resistance, ±5 V/2 V/±5 V, icmos, Dual SPDT Switch ADG436 FEATURES.5 Ω on resistance.3 Ω on-resistance flatness. Ω on-resistance match between channels Continuous current per channel
HY62WT08081E Series 32Kx8bit CMOS SRAM
32Kx8bit CMOS SRAM Document Title 32K x8 bit 2.7~5.5V Low Power Slow SRAM Revision History Revision No History Draft Date Remark 00 Initial Feb.05.2001 Preliminary 01 Revised Feb.13.2001 Final - Change
TOSHIBA MOS DIGITAL INTEGRATED CIRCUIT SILICON GATE CMOS
TENTATIVE TOSHIBA MOS DIGITAL INTEGRATED CIRCUIT SILICON GATE CMOS 262,144-WORD BY 16-BIT FULL CMOS STATIC RAM DESCRIPTION The TC55YEM216ABXN is a 4,194,304-bit static random access memory (SRAM) organized
Packaging Outline. 7mm. FN A = Product Family. Frequency Stability *AA = ±20 ppm (-10 to +70 C) *A = ±25 ppm (-10 to +70 C)
Series Crystal Clock Oscillator (XO) 3.3V CMOS Low Jitter XO Actual Size = 5 x 7mm Product Features Less than 1.5 ps RMS jitter with non-pll design 3.3V CMOS/TTL compatible logic levels Pin-compatible
16-Bit, Single-Channel, Ultra-Low Power, Delta-Sigma ADC with 2-Wire Serial Interface
19-5238; Rev ; 4/1 16-Bit, Single-Channel, Ultra-Low Power, General Description The is an ultra-low-power (< 3FA max active current), high-resolution, serial-output ADC. This device provides the highest
CD4541BC Programmable Timer
CD4541BC Programmable Timer General Description The CD4541BC Programmable Timer is designed with a 16-stage binary counter, an integrated oscillator for use with an external capacitor and two resistors,
ADC Bit µp Compatible A/D Converter
ADC1001 10-Bit µp Compatible A/D Converter General Description The ADC1001 is a CMOS, 10-bit successive approximation A/D converter. The 20-pin ADC1001 is pin compatible with the ADC0801 8-bit A/D family.
CMT-555 DATASHEET Revision: Dec-13 (Modified) HIGH TEMPERATURE RANGE 555 TIMER
The Leader in High Temperature Semiconductor Solutions Revision: 1.4 9-Dec-1 HIGH TEMPERATURE RANGE 555 TIMER General Description The CMT-555 is an extended temperature range, low-power, highly stable
LM12L Bit + Sign Data Acquisition System with Self-Calibration
LM12L458 12-Bit + Sign Data Acquisition System with Self-Calibration General Description The LM12L458 is a highly integrated 3.3V Data Acquisition System. It combines a fully-differential self-calibrating
DTCXO Temperature Compensated Real-Time-Clock Module with SPI bus
DTCXO Temperature Compeated Real-Time-Clock Module with SPI bus Moisture Seitivity Level: MSL=1 FEATURES: APPLICATIONS: With state-of-the-art RTC Technology by Micro Crystal AG Wide range in communication
TABLE 1: PART NUMBER SPECIFICATIONS
22-BIT PROGRAMMABLE PULSE GENERATOR (SERIES SERIAL INTERFACE) FEATU data 3 delay devices, inc. PACKAGE / PIN All-silicon, low-power CMOS technology 3.3V operation Vapor phase, IR and wave solderable Programmable
DTCXO Temperature Compensated Real-Time-Clock Module with SPI bus
DTCXO Temperature Compeated Real-Time-Clock Module with SPI bus Moisture Seitivity Level: MSL=1 FEATURES: APPLICATIONS: With state-of-the-art RTC Technology by Micro Crystal AG Wide range in communication
AUR3840. Serial-interface, Touch screen controller. Features. Description. Applications. Package Information. Order Information
Serial-interface, Touch screen controller Features Multiplexed Analog Digitization with 12-bit Resolution Low Power operation for 2.2V TO 5.25V Built-In BandGap with Internal Buffer for 2.5V Voltage Reference
CARDINAL COMPONENTS. Operating Conditions: Description Min Max Unit
Standard Package Options Series CPP Part Numbering Example: CPP C 1 L Z - A5 B6 - XXXXXX TS CPP C 1 L Z A5 SERIES CPP OUTPUT C = CMOS T = TTL Specifications: PACKAGE STYLE 1 = Full Size 4 = Half Size 5
PACKAGE HIGH-PRECISION VOLTAGE DETECTOR
S-1000 Series www.ablicinc.com ULTRA-SMALL PACKAGE HIGH-PRECISION VOLTAGE DETECTOR ABLIC Inc., 2004-2015 Rev.3.1_02 The S-1000 series is a series of high-precision voltage detectors developed using CMOS
1 Ω Typical On Resistance, ±5 V, +12 V, +5 V, and +3.3 V Dual SPDT Switches ADG1636
FEATURES Ω typical on resistance.2 Ω on resistance flatness ±3.3 V to ±8 V dual supply operation 3.3 V to 6 V single supply operation No VL supply required 3 V logic-compatible inputs Rail-to-rail operation
DS1305 Serial Alarm Real-Time Clock
19-5055; Rev 12/09 DS1305 Serial Alarm Real-Time Clock www.maxim-ic.com FEATURES Real-Time Clock (RTC) Counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the Week, and Year with Leap-Year
Application Circuits 3. 3V R2. C4 100n G PI O. 0 G PI O S e t u p d a ta G PI O. 5 G PI O M o t i o n I n t G PI O. 4 G PI O.
General Description The is an ultra-low power motion detector controller integrated circuit. The device is ideally suited for battery operated wireless motion sensors that make use of an MCU for handling
LC75836W/D. 1/4-Duty General-Purpose LCD Driver
1/4-Duty General-Purpose LCD Driver Overview The LC75836W is 1/4-duty general-purpose microprocessor-controlled LCD driver that can be used in applications such as frequency display in products with electronic
10/February/07, v.1.0 Alliance Memory Inc. Page 1 of 13
FEATURES Access time : 55ns Low power consumption: Operating current :20mA (TYP.) Standby current : 20mA(TYP.)L Version 1µ A (TYP.) LL-version Single 2.7V ~ 3.6V power supply Fully static operation Tri-state
High Temperature, High Voltage, Latch-Up Proof, 8-Channel Multiplexer ADG5298
Data Sheet High Temperature, High Voltage, Latch-Up Proof, 8-Channel Multiplexer FEATURES Extreme high temperature operation up to 2 C Latch-up proof JESD78D Class II rating Low leakage Ultralow capacitance
AS4C256K16E0. 5V 256K 16 CMOS DRAM (EDO) Features. Pin designation. Pin arrangement. Selection guide
5V 256K 16 CMOS DRAM (EDO) Features Organization: 262,144 words 16 bits High speed - 30/35/50 ns access time - 16/18/25 ns column address access time - 7/10/10/10 ns CAS access time Low power consumption