SS1062, SS10621 & SS10621E Free Standing PWC & Fishing Boat Hoist SS1062 SS10621 SS10621E
|
|
- Juniper McDonald
- 6 years ago
- Views:
Transcription
1 SS1062, SS10621 & SS10621E Free Standing PWC & Fishing Boat Hoist SS1062 SS10621 SS10621E Midwest Industries, Inc. Page 1 Ida Grove, IA REV A 1/25/05
2 Bundles Required SS1062 Free Standing Hoist Platform Bundle Wheel Assembly, Lower Frame Hardware Box Leg Bundle SS10621 Free Standing Hoist for PWC & Fishing Boats Platform Bundle Wheel Assembly, Lower Frame Hardware Box Leg Bundle SS10621E Free Standing Hoist for PWC & Fishing Boats with Electric Drive Winch Platform Bundle Wheel Assembly, Lower Frame Hardware Box Leg Bundle SS1062 Assembly Instructions LOWER FRAME AND UPRIGHT POST ASSEMBLY INSTRUCTIONS: STEP 1: STEP 2: STEP 3: STEP 4: STEP 5: Open hardware box #68155 and organize components. Open lower frame bundle #68145; position the lower frames on a flat surface (Diagram V, page 3). Open leg bundle # Some assembly of the component parts has been factory assembled. (Diagram V, Page 3) The two upright posts are identical except for the orientation when the corner block was assembled. Separate and identify their location as shown. Attach the aluminum base pad channel clamp (Ref.#10) to the square base pad (Ref.#1) with two 3/8 X 3/4 carriage bolts and 3/8 hex flange nuts (Detail A). Tighten. Repeat on other base pad. Attach the base pad assembly just assembled to the bottom of the adjustable leg with a 1/2 X 4-1/2 hex bolt and 1/2 hex flange lock nut. Tighten. Repeat on other leg. SS8523 SS8525 SS1226 CF13-62 CC13-62 Accessories / Options Adjustable Leg Bundle Optional Leg Bundle - 80 Legs Electric Winch Kit Canopy Frame Vinyl Canopy STEP 6: Position the two corner post legs as shown in Diagram V. Slide the lower corner blocks into the lower frames. Secure by placing a 3/8 flat washer on a 3/8 X 4-1/2 hex bolt. Place the bolt down through the lower frame and casting (Detail B, page 4). Secure with a 3/8 hex flange nut. Do not tighten. Repeat procedure with the other two corner blocks (Detail M, page 3). Page 2 REV A 1/25/05
3 SS1062 Lower Frame Assembly Page 3 REV A 1/25/05
4 SS10621 / SS10621E Lower Frame Assembly Page 4 REV A 1/25/05
5 Guide Post Assembly SS10621 & SS10621E Assembly Instructions LOWER FRAME AND UPRIGHT POST ASSEMBLY INSTRUCTIONS: STEP 1: STEP 2: STEP 3: STEP 4: STEP 5: STEP 6: Open hardware box #68146 and organize components. Open lower frame bundle #68145; position the lower frames on a flat surface (Diagram I, page 4). Open leg bundle # Some assembly of the component parts has been factory assembled. The winch post leg is longer than the other three corner posts. Separate and identify their location as shown. Attach the aluminum base pad channel clamp (Ref.#10) to the square base pad (Ref.#1) with two 3/8 X 3/4 carriage bolts and 3/8 hex flange nuts (Detail A). Tighten. Repeat on other base pad. Attach the base pad assembly to the bottom of the adjustable leg in the corner post with a 1/2 X 4-1/2 hex bolt and 1/2 hex flange lock nut. Tighten. Repeat on other leg. Position the two corner post legs as shown in Diagram I. Slide the lower corner blocks into the lower frames. Secure by placing a 3/8 flat washer on a 3/8 X 4-1/2 hex bolt. Place the bolt down through the lower frame and casting (Detail B). Secure with a 3/8 hex flange nut. Do not tighten. Repeat the above procedure with the other two corner blocks.tighten all lower frame bolts. Place the round plastic caps into the top of the posts (Detail C, page 4). Page 5 REV A 1/25/05
6 Platform Assembly Page 6 REV A 1/25/05
7 SS10621 Assembly Page 8 REV A 1/25/05
8 SS10621 Bill of Materials STEP 12: STEP 13: Install the brace tubes (Item #2, Diagram IV, page 8) by inserting a 3/8 X 5 hex bolt through a 3/8 flat washer, then through one end of the brace tube and down through the lower frame. Secure with a 3/8 flange lock nut. Attach the other end of the brace tube to the upright post by inserting a 3/8 X 4-1/2 hex bolt through a 3/8 flat washer. Insert the bolt through the hole provided in the upright post, and then through the end of the brace tube. Secure with a 3/8 hex flange lock nut. Tighten both ends. Repeat on the other brace tube. Secure a pulley assembly to the front cross member by inserting a 3/8 X 1-3/8 X 3-1/4 U-bolt in the hole of the pulley clevis, then inserting it through the holes provided in the front cross member (Detail H & I, pages 6 & 8). S e c u r e t o t h e c r o s s m e m b e r w i t h 3/8 hex flange lock nuts. Tighten until two threads of the U-bolts are exposed through the nuts. Repeat on the other pulley on the other end of the front platform. SS1062 & SS10621 WINCH INSTALLATION: STEP 14: ShoreStation Wheel Assembly Locate the winch and mounting plate (Diagram IV and Detail K, page 8). Attach the winch to the mounting plate using three 3/8 X 1 hex bolts and hex flange lock nuts. Tighten. Attach the top of the mounting plate to the winch post by inserting a 3/8 X 4-1/2 hex bolt through a 3/8 flat washer and then inserting the bolt through the hole provided at the top of the winch post. With the bolt fully inserted, slip the top center hole in the mounting bracket over the bolt and secure in place with a 3/8 flat washer and 3/8 hex flange lock nut. Secure the bottom of the bracket to the post using a 3/8 X 3-7/8 X 4-5/8 round U-bolt, and hex flange lock nuts. Tighten. Page 9 REV A 1/25/05
9 SS1061E Page 11 SS10621E ELECTRIC WINCH INSTALLATION: STEP 14: Locate the electric winch, mounting plate, and clamps in the hardware box (Detail N, page 13). Note that the mounting plate has one hole on the bottom and two on the top. Attach the electric winch to the mounting plate by placing a 3/8 X 1 hex bolt into the hole closest to the center of the bracket and then through the winch case. Secure with a 3/8 hex flange lock nut. Place a 3/8 X 5 hex bolt through a 3/8 flat washer and insert into the top hole in the upright post. Place one of the U-bolt yokes provided on the bolt so that it fits the diameter of the upright post. Slip the winch mounting bracket with winch attached onto the bolt using the top hole of the mounting bracket. Secure with a 3/8 hex flange lock nut. Attach the bottom of the mounting bracket to the post with another 3/8 X 5 bolt, flat washer, U-bolt yoke and hex flange lock nut as described previously. Tighten. Attach the controller arm weldment to the front crossmember with 3/8 X 3-7/16 X 3 square U-bolt and 3/8 hex flange lock nuts. Note that the controller arm can be positioned in or out from the centerline of the hoist to best fit your needs. Place the controller holder in the top of the controller arm. Slip the controller into the holder by feeding the cord into the slot in the holder and then placing the controller into position. Page 10 REV A 1/25/05
10 SS1226 Electrive Drive Assembly Page 11 REV A 1/25/05
PO BOX 130 CLEAR LAKE, MN
WWW.WALKSONWATER.COM PO BOX 130 CLEAR LAKE, MN 55319 320-743-3333 PARTS LIST FOR 30115# VERTICAL BOAT LIFT 2-Back Leg Uprights 1 right, 1 left (BL) 1-Front Leg Upright (FL) 1-Winch Leg Upright (WU) 2-Bottom
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More information200A FLB VERTICAL 22113V LIFT W/CHAIN DRIVE WINCH
PG. 1 OF 11 PORTA-DOCK, INC. 200A FLB VERTICAL 22113V LIFT W/CHAIN DRIVE WINCH STEP 1. Separate and group like parts and fasteners together. Locate the winch side member with the longer upright tube and
More informationM2 Assembly. M2 Sub-Assemblies mm Belt Sub-Assembly mm Belt Sub-Assembly Spider Sub-Assembly... 4
M2 Assembly Table of Contents M2 Sub-Assemblies... 3 630mm Belt Sub-Assembly... 3 702mm Belt Sub-Assembly... 3 Spider Sub-Assembly... 4 Idler Bolt Sub-Assembly... 8 Y Motor Sub-Assembly... 9 X Motor Sub-Assembly...
More informationPVB Prairie View Pontoon Fishing Trailer
PVB1412-03 Prairie View Pontoon Fishing Trailer PVB1412-03 Prairie View Pontoon Fishing Trailer 62340 Literature Bag - Trailers 6606703 Frame Bundle - Pontoon Fishing 6578003 Tongue - 3x3x14 ga. x 7 66066
More informationUser Instructions Multiline Otter Scoreboard Caddy Assembly
List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)
More informationF l a t S c r e e n A R M S I n s t a l l a t i o n
ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)
More informationThank you for purchasing out product! *Please read these instructions and follow them step by step. *
Page 1 of 7 AD17 AA DS 4 X 16 T12 Thank you for purchasing out product! *Please read these instructions and follow them step by step. * STEP 1. Slide two support posts (REF. # 24) into the two outside
More information3,500/4,500lb. Vertical Cable Feighner Lift
3,500/4,500lb. Vertical Cable Feighner Lift CAUTION - PUT SAFETY FIRST 1. Before attempting to install or operate this lift, study and fully understand the proper operating procedures and safety precautions
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More information4832A Installation Sheet Part List
4832A Installation Sheet Part List (1) 4016A-43-003 Qty 1- (2) 4016A-43-002 Qty 1- (3) 4016A-43-001 Qty 2- (4) 4016A-10-005 Qty 1- (5) 4016A-43-004L Qty 1- Mounting Bolt Kit (A) (K) Qty 2 - Qty 6 - M10
More informationREAD CAREFULLY - FAILURE TO FOLLOW INSTRUCTIONS AND SAFETY RULES MAY RESULT IN SERIOUS INJURY
LSV30108C LS5002C cradle bundle 108 LS5004B bunk bundle LSV40108C LS5002C cradle bundle 108 LS5004B bunk bundle LS5007B diagonal bundle LSV30120C LS5012C cradle bundle 120 LS5004B bunk bundle LSV40120C
More informationGared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
More informationAssembly Instructions 10 X 10 Aluminum Roof Support
Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1
More informationThank you for purchasing our product! *Please read these instructions and follow them step by step.*
07/07/08.rev1 PAGE 1 OF 11 601AL VERTICAL 60120VL LIFT W/CHAIN DRIVE WINCH Thank you for purchasing our product! *Please read these instructions and follow them step by step.* Step 1. Separate and group
More informationThis manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified.
This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified. Step #1 Lay all parts out to verify quantities. (2) 2 x 25-1/4
More informationShoreline Canopy and Canopy Frame Installation Instructions
Shoreline Canopy and Canopy Frame Installation Instructions INTRODUCTION The Shoreline canopy is used with the Shoreline Cantilever boat lifts. There are several different sizes and a variety of color
More informationREAD CAREFULLY - FAILURE TO FOLLOW INSTRUCTIONS AND SAFETY RULES MAY RESULT IN SERIOUS INJURY
Owner s Manual LSV50120B LS5000B leg bundle LS5021B post bundle LS5022B cradle bundle V50120B straight LS5003B spreader bundle LS5004B bunk bundle LS4005B accessory box LS2005B wheel LS5007B diag bundle
More informationInstallation Instructions Kit, Base Rail Bracket Part # 31413
Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating and
More informationASSEMBLY AND ADJUSTMENT
EPPA MONITOR ARM EPPA Rev A 10/17 Model EPPA-XXX ASSEMBLY AND ADJUSTMENT EPPA MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check
More informationPORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12
Page 1 of 7 PORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12 *For Beige Decking Add the Letter B to Model* Thank you for purchasing out product! *Please read these instructions and follow
More informationMANUAL DE MONTAJE ASSEMBLY MANUAL AIREADOR DE PLUG AERATOR MODEL # AE-48T. Hardware & Parts Listing Assembly Instructions Maintenance Notes for
ASSEMBLY MANUAL Hardware & Parts Listing Assembly Instructions Maintenance Notes for 48 PLUG AERATOR MANUAL DE MONTAJE Lista de piezas y tornillería Instrucciones de armado Notas de mantenimiento para
More informationInstruction Guide 4A90L
Instruction Guide 4A90L Kargo Master Rancho Cordova, CA 95742 800-343-7486 CustomerService@KargoMaster.com DATE: *PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING, INSTALLING, AND USING THIS
More informationInstallation Instructions
Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation 2. Install in accordance with manufacturer s installation instructions. Failure
More informationHip Roof Canopy Instructions
Hip Roof Canopy Instructions - PUT SAFETY FIRST. NOT COMPLYING WITH THE PROCEDURES AND PRECAUTIONS OUTLINED IN THIS MANUAL MAY RESULT IN PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.. Before attempting
More informationELSTON. Gopher Getters. Parts List for GA-400 and GA-500 ELSTON MANUFACTURING INC. Please Contact Us for Parts and Service:
ELSTON Gopher Getters Parts List for GA-00 and GA-00 Another Quality Product of: Please Contact Us for Parts and Service: ELSTON MANUFACTURING INC. 70 N Weber Sioux Falls, SD 70 www.elstonmfg.com -800-8-8
More informationSTEP 1 STEP 2 LEVELER KIT OPTION MOBILE CASTER KIT OPTION
B SERIES INDUSTRIAL BENCHES TOOLS REQUIRED FOR ASSEMBLY Socket set, Open end wrench set, Cordless drill with 3/8" socket bit (Magnetic recommended). BEFORE ASSEMBLY Read through the assembly instructions
More informationINSTALLATION INSTRUCTIONS 6 OVAL BENT END SIDEBARS DODGE RAM 1500, CREW CAB PART#: /241533B
PARTS LIST: 1 Driver/Left Sidebar 24 8mm x 24mm x 2mm Flat Washers 1 Passenger/Right Sidebar 12 8mm Lock Washers 3 Driver/left, Passenger Center and Rear 6 8mm Hex Nuts 3 INSTALLATION INSTRUCTIONS 6 OVAL
More informationINSTALLATION INSTRUCTIONS / DODGE RAM CREW CAB 2500/3500
INSTALLATION INSTRUCTIONS 225019 / 225019-2 2010 DODGE RAM CREW CAB 2500/3500 PARTS LIST: Qty Description Qty Description 1 Driver/Left Side Bar 4 Plastic Square Retainer 1 Side Bar 2 12mm x 120mm Hex
More informationCalf-Tel Pen System Assembly Instructions
Calf-Tel Pen System Assembly Instructions (Instructions work for 4, 6, and the 7 Pen Systems) 1 ASSEMBLY OF PEN FRONT AND WALLS START THE ASSEMBLY BY LINING UP THE TWO UNI-DIRECTIONAL ARROWS IN THE TOP,
More informationHiniker Company th St. P.O. Box 3407 Mankato, MN VEHICLE INSTALLATION INSTRUCTIONS FOR: CHEV/GMC 4x4: K1500 SILVERADO/SIERRA
VEHICLE INSTALLATION INSTRUCTIONS FOR: CHEV/GMC x: 007 03 K500 SILVERADO/SIERRA Page of 5 Hiniker Company 58766 0th St. P.O. Box 307 Mankato, MN 5600 INSTRUCTION SHEET NO: 505 Rev. A August 0, 03 IMPORTANT:
More informationPickup Box Utility Rack Package Installation (Instruction ID: )
017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation
More information55000/55010 Installation Instructions
A. Install 55015 B. Bolt roof rails, 55020/55025, to front hoop. C. Assemble 55026 D. To install without drilling into bumper. E. If mounting directly to bumper. A. 55015 Installation Instructions 55000/55010
More informationStainless Steel Bench Stand
Installation Manual Stainless Steel Bench Stand Product(s): 29600 29601 51229 2016 by Fairbanks Scales, Inc. Revision 2 02/16 All rights reserved. Amendment Record STAINLESS STEEL BENCH STAND Document
More informationREAD CAREFULLY - FAILURE TO FOLLOW INSTRUCTIONS AND SAFETY RULES MAY RESULT IN SERIOUS INJURY
Owner s Manual LSV50120B LS5000B leg bundle LS5021B post bundle LS5022B cradle bundle V50120B straight LS5003B spreader bundle LS5004B bunk bundle LS4005B accessory box LS2005B wheel LS5007B diag bundle
More informationFLOE quick attach & standard sectional dock and leg kits
FLOE quick attach & standard sectional dock and leg kits assembly instructions KIT P/N 510-02550-00 X-SHALLOW KIT P/N 510-02551-00 SHALLOW KIT P/N 510-02552-00 MEDIUM KIT P/N 510-02553-00 DEEP WARNING
More informationREAD CAREFULLY - FAILURE TO FOLLOW INSTRUCTIONS AND SAFETY RULES MAY RESULT IN SERIOUS INJURY
LSV30108B LS5002B cradle bundle 108 LS5004B bunk bundle LSV40108B LS5002B cradle bundle 108 LS5004B bunk bundle LS5007B diagonal bundle LSV30120B LS5012B cradle bundle 120 LS5004B bunk bundle LSV40120B
More informationPassenger/Right Center and Rear Support Brackets. Driver/Left Center and
PARTS LIST: 1 Driver/Left HD Running Board 24 8mm x 24mm OD x 2mm Flat Washers 1 Passenger/Right HD Running Board 12 s 3 Driver/Left front, passenger center/rear Support Brackets 6 8mm-1.25 Hex Nuts 3
More informationHOUSE PARTS PACKED IN HOUSE BOX PARTS IN PLASTIC BAG (HARDWARE) PARTS IN SMALL PLASTIC BAG (FLOOR CLIPS) PARTS PACKED IN BUNDLE
Check parts against this list before starting assembly. Refer to illustrations on pages 6 and 7 to view house parts. If any shortages are found, refer to Packing Slip for claim instructions. Item 3 5 6
More informationINSTALLATION INSTRUCTIONS MAIN BAR TIPO B 90002, 91002, 91502, 92002, 93002, 94002, 95002, 96002, y PS / B / C
Parts List: i) 4-7/16" Plastic cap Not Includes: a) 1- Driver Leg 8-3/8x1 1/2" Flat washer Kicker b) 1- Passenger Leg 8-3/8" Hex nut c) 1- Cross bar 4-3/8x 1 1/2" Carriage bolt d) 2- Mounting plate 4-3/8x
More informationSTANDARD GRAVITY BOX TARP INSTALLATION
OPERATORS MANUAL Rev. 9.9.2016 STANDARD GRAVITY BOX TARP INSTALLATION J. & M. Mfg. Co., Inc. 284 Railroad Street - P.O. Box 547 Fort Recovery, OH 45846 Ph: (419) 375-2376 Fax: (419) 375-2708 www.jm-inc.com
More informationMANUFACTURING INC. 706 N
ELSTON Gopher Getters Parts List for GA-00 & GA-00 Please Contact Us for Parts and Service: Another Quality Product of: ELSTON MANUFACTURING INC. 70 N Weber Sioux Falls, SD 70 www.elstonmfg.com -800-8-8
More informationA59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK
Page 1 of 5 PORTA-DOCK, INC. A59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK *For Beige Decking Add the Letter B to model* Thank you for purchasing our product! *Please read these instructions and follow
More informationJenny Legs Assembly Instructions
Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:
More informationFor additional assistance call
The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or
More informationTIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together
More informationINSTALLATION INSTRUCTIONS
NOTE: Bolts should remain hand tight until all bolts are installed. STEP 1 Installing the door base (both sides). 1. Locate the outer, roll cage, mounting bolt (passenger side is shown in the illustration).
More informationINSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger
INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger TOOLS REQUIRED FOR INSTALLATION: Drill motor, (1) 5/16 inch drill bit, (1) 13/64 drill bit, (1) 3/16 inch hex wrench (1) 3/32 inch hex wrench.
More informationMODEL 83 Pail Handler
MORSE MFG. CO., INC. 727 West Manlius Street P.O. Box 518 East Syracuse, NY 13057-0518 Phone: 315-437-8475 Fax: 315-437-1029 Email: service@morsemfgco.com Website: www.morsemfgco.com COPYRIGHT 2005 MORSE
More information(6) Plastic Retainers. Passenger/Right. Passenger/Right Support Brackets
PART#R102580 PARTS LIST: 1 Driver/Left HD Running Board 4 8mm Bolt/Nut Plates 1 Passenger/Right HD Running Board 4 8mm Plastic Retainers 2 Driver/Left & Center Mount Bracket 14 8mm-1.25 x 30mm Hex Bolts
More information08+ KAWASAKI KLR PD NERF
08+ KAWASAKI KLR PD NERF 0505-1299 Before you begin, place the bike on a hard level surface where you have room to work. Lay out the parts included in this kit and compare to the parts list on page 5 of
More informationINSTALLATION INSTRUCTIONS 3 ROUND & 4 OVAL SIDEBAR (90-DEG BENT END) DODGE RAM MEGA CAB PART NUMBER SB1214S SB1214B
INSTALLATION INSTRUCTIONS PART NUMBER SB1214S SB1214B PARTS LIST: Qty Description Qty Description 1 Driver/Left Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Passenger/Right Sidebar 4 12mm Lock Washers
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationMAG-CONV Basic, 48, 48R & Midline Front Mount
Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total
More informationS48-L12-SC AND G48-L12-GC STEEL PORTA-DOCK S82 SC 6 X 12 PLATFORM AND G82 GC 6 X 12 PLATFORM
PAGE 1 OF 6 PORTA-DOCK, INC. S48-L12-SC AND G48-L12-GC STEEL PORTA-DOCK S82 SC 6 X 12 PLATFORM AND G82 GC 6 X 12 PLATFORM Thank you for purchasing our product! *Please read these instructions and follow
More informationRoll In W/L Dock PAGE 1
Roll In W/L Dock PAGE 1 1 2 3/8 X 1 CARRIAGE BOLT SS 3/8 FLANGE NUT BRASS 3 4 1/2-13 X 1.25 SQ BOLT SS 1/2 SQ NUT BRASS 5 3/8-16 X 2.5" BOLT SS PAGE 2 6 7 BRACE BRKT SINGLE AXLE TUBE 8 9 3" AXLE WASHER
More informationInstruction Manual. LSV36108A 3600# Vertical Lift LAKESHORE PRODUCTS, INC.
LAKESHORE PRODUCTS, INC. Quincy. MI. 49082. tel 517.639.3815 LSV36108A 3600# Vertical Lift Instruction Manual Read carefully. Failure to follow the instructions and safety rules could result in severe
More informationE4-WM5-Y525A00 MOUNTING INSTRUCTION
RAM 2500/3500 4WD B8 5100 (Dual Steering Damper Kit) The installation of these steering dampers must be performed only by experienced and qualified personnel. Read and follow the installation instructions
More informationU.S. Solar Mounts TOP Mount Installation Instructions. Adjustable 4 (2) 60-Cell Module Top-of-Pole Mount REV 1
U.S. Solar Mounts 4260 TOP Mount Installation Instructions Adjustable 4 (2) 60-Cell Module Top-of-Pole Mount REV 1 Ultra-Rugged Solar Mounting Solutions 2017 U.S. Solar Mounts Corp. All Rights Reserved
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For Chevrolet Silverado 1500HD & 2500 Kit 68162 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of
More informationInstructions and Parts List DR-12N Martin House
Form 36-99 Instructions and Parts List DR-N Martin House Note: It is necessary to install a post before house is put up, but the house can be assembled at any time. House parts Check parts against this
More informationSupport. (3)Passenger Support. Brackets. (2) Running Board (example only)
IB(5,4)) RUNNING BOARD PARTS LIST: Item QTY Description Item QTY Description #01 2 Running Board(use for left or right) #10 12 8mm Lock Washers #02 3 Driver Mounting (/Center/Rear) #11 6 8mm Hex Nuts #03
More informationEMB Manufacturing Inc Boomer Line St. Clements, On N0B 2M0 Canada Ph: (519) Fax: (519) P200
BY EMB MFG INC. EMB Manufacturing Inc. 4144 Boomer Line St. Clements, On N0B 2M0 Canada Ph: (519) 699-9283 Fax: (519) 699-4146 www.embmfg.com P200 Pivoting Chainsaw Holder Accessory Installation Instructions
More information1503 Follow Spot Yoke, Source Four LED
1503 Follow Spot Yoke, Source Four LED Rev 1.0 2016 City Theatrical, Inc. Getting Started with the City Theatrical Follow Spot Yoke for source four LED Congratulations on the purchase of your City Theatrical
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationCHEVY SuperBracket Mounting Kit #0826
CHEVY SuperBracket Mounting Kit #0826 #1200 SuperGlide (16K) #0800 SuperGlide (20.5K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer Weight (Maximum)
More informationOwner s Manual AE PLUG AERATOR MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE Made In CHINA REV
MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945 Owner s Manual AE-48 48 PLUG AERATOR IMPORTANT Read and follow all Safety Precautions and Instructions Before Operating this Equipment. Made In CHINA
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationKAWASAKI KLRE PD NERF HTP4-8-5 & HIGHWAY PEGS HTP4-1-4B
Thank you for purchasing Happy Trails products. Our products are proudly hand made in Boise Idaho, USA. If you have any questions or concerns about the installation of this product, please contact us directly
More informationABM International, Inc. Navigator Assembly Manual
ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor
More informationTROLLA LEAVY 97 CM Lawn sweeper
TROLLA LEAVY 97 CM Lawn sweeper Artikel nr.: 1008 EN Operating manual 014/1 Dear Customer, Congratulations on your new Trolla product. We hope you will enjoy it. Checkout with your new Trolla product may
More informationHardware and Components:
Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD FORD ESCAPE
INSTALLATION INSTRUCTIONS GRILLE GUARD 08-010 FORD ESCAPE PARTS LIST: 1 Grille Guard 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Frame Mounting 4 10mm Lock Washers 1 Passenger/Right Frame Mounting 6 10mm
More informationSize Grade Torque 9/ ft/lbs. 5/ ft/lbs. 3/ ft/lbs. 7/ ft/lbs ft/lbs.
8-3 HJ3205,Rev 4 BOlT TORQUE SPECIfICATIONS STANDARD BOlTS: Size Grade Torque 5/6 5 20 ft/lbs. 3/8 5 35 ft/lbs. 7/6 5 56 ft/lbs. /2 5 85 ft/lbs. Size Grade Torque 9/6 5 23 ft/lbs. 5/8 5 70 ft/lbs. 3/4
More informationGMQ 16 Adapter Set Assembly Instructions Copyright November, 2003 GraceWood, Inc. Table of Contents
GMQ 16 Adapter Set Assembly Instructions Copyright November, 2003 GraceWood, Inc. Table of Contents Parts List.................................................................. 1 Assembly Instructions.......................................................3
More informationAPS Small Seeds Box Assembly Instructions
APS Small Seeds Box Assembly Instructions For APS15 Series All Purpose Seeder Manual No. 313-473M Before You Start! When you see this symbol, the subsequent instructions and warnings are serious - follow
More informationFootball Goal Posts MODEL SERIES: FGP400 and FGP600 series
Football Goal Posts MODEL SERIES: FGP400 and FGP600 series Installation and Maintenance Instructions Please read all instructions before attempting installation of these units SAVE THESE INSTRUCTIONS FOR
More informationSOCCER TABLE. Assembly Instructions
Updated: 5/4/16 SOCCER TABLE Assembly Instructions Table of Contents Parts Identifier... 3 Hardware Identifier. 4 Table Assembly Instructions... 5 Table Assembly Pictures..... 6, 7, 8 2 Page Parts Identifier
More informationO-Sullivan King 4 Poster Bed O-Sullivan Queen 4 Poster Bed Parts and Hardware List
Parts and Hardware List A. Left Headboard Post 1 pc B. Right Headboard Post 1 pc C. Left Footboard Post 1 pc D. Right Footboard Post 1 pc E. Headboard Panel 1 pc F. Footboard Rail 1 pc. Spindles 4 pcs
More informationSTEP 1 : DESTROYER FRONT BUMPER INSTALL GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... *shorty bumper to show hardware* Tools Required:
DESTROYER FRONT BUMPER INSTALL JL STEP 1 : GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... Tools Required: - Utility knife - 11/16 Deep socket - Ratchet - 11/16 Crescent wrench - Ratchet Extension - 1/4 socket
More informationToyota 4 Runner and Lexus GX Skid Plate installation instructions.
Toyota 4 Runner and Lexus GX Skid Plate installation instructions. NOTE: When installing the full set of skid plate start at the rear of the vehicle and work your way forward. NOTE: Torque Specs: Tighten
More informationOWNERS MANUAL MODEL F660 HIP SLED
OWNERS MANUAL MODEL F HIP SLED QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will guarantee your complete
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD CHEVY TAHOE / AVALANCHE 1500/ SUBURBAN 1500 PART # /502795
(W) INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 502794/502795 PARTS LIST: 1 Grille Guard 2 12-1.75mm x 140mm Hex Bolts 2 Frame Mounting Brackets 8 12-1.75mm x 30mm Hex Bolts 2 Lower Support Brackets
More informationInstructions and Parts List MSS-12W MARTIN SAFETY SYSTEM
HOUSE PARTS PACKED IN HOUSE BOX Code # Item Qty Description 950 9776 77 85036 500 868 635 9635 5075 860 3578 8507 60 6 95065 6 98000 7800 7806 3 5 6 7 7A 8 9 0 3 5 6 6A 6B 8 Instructions and Parts List
More informationPassenger/Right Front Mounting Bracket
PARTS LIST: 1 Driver side running board 1 8mm Insert Installation Tool 1 Passenger side running board 4 10-1.50mm x 35mm Hex Bolt 1 Driver 10 10mm x 24mm OD x 2.2mm Flat Washer 1 Passenger 6 10mm Lock
More informationParts list continues on Page 2 HOUSE PARTS PACKED IN HOUSE BOX PARTS IN SMALL PLASTIC BAG (HARDWARE) POST PARTS PACKED IN THIS BOX (LARGE PLASTIC BAG)
Form 05-07 Instructions and Parts List MSS- Martin Safety System NOTES: () A complete system is packed in two boxes post box and house box. House box contains hardware for both post and house assembly.
More informationSHOREMASTER DOCK SECTIONS Instructions and Safety Tips
SHOREMASTER DOCK SECTIONS Instructions and Safety Tips Infinity RS Infinity TS9 Infinity RS Floating FTS9 PUT SAFETY FIRST To prevent serious personal injury or death, study and fully understand the proper
More information2-PIECE STAIRWAY ASSEMBLY
REVISED 2/12/15 2-PIECE STAIRWAY ASSEMBLY STEP 1: LAY OUT THE RIGHT AND LEFT SIDE TOP AND BOTTOM RISER PANELS AS SHOWN IN FIGURE 1. BOLT THE SPLICE PLATE (#15114C for OSHA F SERIES; #15412C for BOCA U
More informationParts list Instruction guide Warnings Please read carefully before assembling and using product.
Parts list Instruction guide Warnings Please read carefully before assembling and using product. Jet Rail XL Part Number 27377 Tools required for assembly Hammer 9/16 Wrench 3/4 Wrench Ratchet 9/16 Socket
More informationFIRST TEAM SPORTS, INC.
FIRST TEAM SPORTS, INC. INVADER EZ-CRANK PORTABLE BASKETBALL GOAL ASSEMBLY INSTRUCTIONS Revised - 08/04/10 BILL OF MATERIALS (1) BASE TANK (1) BACKBOARD MOUNT (2) 5/16 X ¾ HEX BOLT (1) LOWER POST (2) SPRING
More informationThe Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.
The Phoenix Professional Quilting Frame Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.1 1 The Phoenix Professional Quilting Frame Parts List Box 1...3 Box
More informationframe bracket Dodge x 2 & 4 x 4 (6-1/2 & 8 Boxes Includes Mega Cab)
, Rev 4 02/19 frame bracket 8552026 Dodge 3500 4 x 2 & 4 x 4 (6-1/2 & 8 Boxes Includes Mega Cab) 14 5 7 2 4 11 9 10 17 3 6 1 8 13 15 16 18 12 ITEM PART # DESCRIPTION QTY. 1 00085.50 FLAT WASHER 10 2 00248
More informationMulti-Stage ASSEMBLY INSTRUCTIONS ST-8100 SERIES. 125 TAYLOR PARKWAY ARCHBOLD, OH PHONE: (419) FAX: (419)
125 TAYLOR PARKWAY ARCHBOLD, OH 43502 PHONE: (419) 445-8915 FAX: (419) 445-0367 www.biljax.com Multi-Stage ST-8100 SERIES ASSEMBLY INSTRUCTIONS ALL DRAWINGS ARE FOR ILLUSTRATION ONLY. PRINTED IN U.S.A.
More informationYour order will be shipped with the supports and rail components packaged inside the ramp package. Each accessory package is labeled.
instructions About Your Order. Your order will be shipped with the supports and rail components packaged inside the ramp package. Each accessory package is labeled. Check the Order Before the Carrier leaves!
More informationINSTALLATION INSTRUCTIONS
Do not attempt to install this product on any vehicle other than the one it is designed for and listed above! Parts List 10 3/8 X 1 1/4 Hex Bolt 10 3/8 Lock Washer 4 3/8 Hex Nut 4 3/8 Flat Washer 2 3169)
More informationHorizontal Cable Systems
ALUMINUM RAILING INSTALLATION INSTRUCTIONS v2012 orizontal Cable Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 1A) Coastal applications:
More informationPack Mount Instructions:
Pack Mount Instructions: STEP 1 Mounting upright base to desired surface If mounting to a surface with an accessible backside (such as a thin walled container): Option 1 Discard the Round Mounting Disk
More informationBIFOLD FUTON FRAME TRINITY ARM. Seat Rails and Slats x 1. *Note: Use 4pc of 100mm Bolts and 4pc of 60mm Bolts to attach the arms to the Stretchers.
1A Parts in this box. 2pc with extra holes 2pc with extra holes & plastic stoppers Arms x 2 Back Rails and Slats x 1 Full Size: Slat Supports x 6 3pc are longer for the Back deck Back Side Rails x 2 Seat
More informationHardware and Components:
Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)
More information