Model WHD Weld Hole Detector Operator s Manual. Rev 1.1
|
|
- Marjory Parsons
- 6 years ago
- Views:
Transcription
1 Model WHD Weld Hole Detector Operator s Manual Rev 1.1
2 Contents 1. Introduction Description Model Nomenclature Operating Principle Specifications Location and Mounting Sensor Location Sensor Mounting Utility Connections Electrical Connections... Error! Bookmark not defined. 5. Operation Controls... Error! Bookmark not defined. 5.2 Debugging... Error! Bookmark not defined. 6. Maintenance Regular Maintenance Returns of the WHD... 7 P a g e 1
3 1. Introduction The Logika Technologies Weld Hold Detector, Model WHD, is primarily used in the metallurgical industry to detect weld holes in plate production lines. These holes are purposely made at weld seams so these seams may be later detected and cut out of the rolled product. The WHD consists of two parts: an emitter and a receiver. Typically, the Emitter is mounted above the sheet line and the Receiver directly below it so that the sheet blocks out the majority of ambient light. 2. Description 2.1 Model Nomenclature 2.2 Operating Principle The Logika Weld Hole Detector is comprised of an emitter and a receiver mounted above and below a steel sheet line. The emitter produces modulated infrared light that is collimated by a series of lenses. Normally, the steel plate blocks all of the light so that nothing reaches the receiver. Wherever a seam is welded in the steel plate, a hole is also punched to mark the seam. When a marked seam reaches the detect zone, the receiver will see the light through this hole and set an output. P a g e 2
4 2.3 Specifications Field of View: The length of the optical array is the same as the area scanned for weld holes. For single weld hole detection: 304mm(12 ) or 408 mm (16 ) Double hole detection 527mm (21 ) Max Sheet Speed: 900 m/min (2950 feet/min) Response: 1ms Working Distance: Weld hole 10mm (0.4 inches): Max working distance 1.2m (48 inches) Weld Hole 20 mm (0.8 inches): Max working distance 3m (118 inches) LED Indicator: Emitter : Green = power on, Red=emitter alarm Receiver: Red = detect, Yellow=sync alarm(on Alarm) Output: Relay contact (1NO,1NC) Contacts AC250V 5A; DC 30V 5A PNP output: maximum current 100mA with overload protection Output Delay: Output Signal Reset Delay, range from 0-4 sec Power Input: 24VDC±10%, 110VAC ±10%, 220ACV 20 VA Ambient: Temperature limits for electronics; -20 o C to 70 o C (-4 o F to 158 o F) Size See attached drawings Weight: 10 kg total (22 lbs) P a g e 3
5 3. Location and Mounting 3.1 Sensor Location The Logika WHD should not be installed above a significant heat source. Also avoid direct exposure to water vapor or excessive dust or smoke. The user may wish to improve the installation with heat shields or fans to dissipate the water vapor or smoke. Emitter and Receiver should be mounted as close as possible for receiver to get strongest infrared input signal. Maximum ambient temperature at the WHD is 70 o C (158 o F) 3.2 Sensor Mounting Installation- WHD comes with adjustable mounting brackets to align the emitter and receiver. Typically, the Emitter is mounted above the detect target with the lens facing down, the receiver is mounted underneath the target with the lens facing up, two lenses should be aligned properly by adjust the mounting brackets. Aiming- The emitter/receiver pair should be mounted so they are centered squarely across the product as it moves down the line. P a g e 4
6 4. Utility Connections Power Connections- Power Input (please specify power input at time of order). Number Color Function 1 Yellow +24VDC 2 Green 0VDC 3 Purple PNP Hi=Detect 4 Gray Relay NC. 5 White Relay Common 6 Pink Relay NO. Figure 4.1: WHD-S-24-P Cable Terminal Wiring Description Electrical Overview 1) Single Hole Detection Systems: All electrical connections to the WHD system are made via a 2m (7 ) 12-pin connector (with ground) on the Emitter. There is a second connection directly between the Emitter and Receiver via a 4 conductor, 3m (10 ) cable. Other cable lengths are available from Logika Technologies upon request. 2) Double Hole Detection Systems: All electrical connections to the WHD system are made via a 2m (7 ) 12-pin connector (with ground) on the Receiver. The Emitter is supplied with power only (110VAC or 220VAC) on a standard 2m (7 ) cable. Other cable lengths are available from Logika Technologies upon request. Cable Specification Outer steel braid for mechanical protection. Overall diameter of 9 mm. (0.35 ) Minimum bending radius of 30 mm. (1.18 ) Each conductor is color-coded and numerically tagged. Conductors are terminated with ferrules P a g e 5
7 Junction Box Wiring- Please see the Cable Terminal Wiring Description Figure 4.1 below for the sensor wiring terminal description. The supplied cable should be connected directly to the terminals of a junction box. All cables must be shielded all the way to the junction box with the shield connected to ground to eliminate electrical noise, which may trigger false detection. Any unused output wires must have insulation protection or be connected to a free terminal of junction box. 5. Operation 5.1 Single Hole System There are adjustment potentiometers on both Emitter and Receiver units. Receiver: Turning Time pot clockwise increases Detect signal on time(0-3s) Single Hole Debugging System does not detect weld holes: 1) Determine that the red Detect LED illuminates when no steel is present. If not, check power connections, Emitter/Receiver cable connections, Emitter/Receiver alignment. 2) If the red LED does illuminate but no signal is received by the line controller (PLC), check connections to the output lines. System Detect output stays on: Check alignment of WHD system to steel sheet. Ensure that the Emitter/Receiver pair is not past either edge of the sheet. 5.2 Double Hole System 6. Maintenance P a g e 6
8 6.1 Regular Maintenance Regular attention to the following will ensure steady operation of the sensor: Lens Cleaning- Routinely check the WHD lens glass for dust or oil residue. When necessary, clean the glass with alcohol and lens paper or soft cloth. 6.2 Returns of the WHD Contact LOGIKA at ( LOGIKA ) with the Serial Number of your sensor before you return our product. If we are unable to solve the problem by phone or , LOGIKA will then provide you with a return authorization number. Do not return the WHD without an authorization number. If the product is out of warranty, we will provide a repair estimate and then complete the repairs after your approval. P a g e 7
9 7. Enclosure Dimensions 7.1 Single Hole WHD Emitter Steel plate Glass Receiver P a g e 8
10 7.2 Double Hole WHD Steel plate P a g e 9
Model OB-ITF Infrared Through-Beam Fiber Optic Optical Barrier Operator s Manual. Version
Model OB-ITF Infrared Through-Beam Fiber Optic Optical Barrier Operator s Manual Version 11-2010 Contents 1. Introduction... 2 2. Description... 2 2.1 Model Nomenclature... 2 2.2 Operating Principle...
More informationModel LS 250 Loop Scanner Operator s Manual. Version
Model LS 250 Loop Scanner Operator s Manual Version 05-2011 Contents 1. Introduction...2 2. Description...3 2.1 Model Nomenclature...3 2.2 Operating Principle...3 2.3 Specifications...5 3. Location and
More informationLabel Sensor. Ordering Information. Application Example E3S-CD68/CD63. Ideal for Detecting Labels on Bottles. E3S-CD68/CD63 Label Sensor
Ideal for Detecting Labels on Bottles Satisfies the requirements of IP67. Ensures a vibration resistance of 10 Hz to 2 khz and a shock resistance of 1,000 m/s 2 (approximately 100G). Incorporates an NPN
More informationOperating mode. distance. 7 m Light ON Dark ON (selectable) 2 m [100 mm] (See note 1.) 100 mm (wide view)
Built-in Amplifier Photoelectric Sensor E3S-A/B Revolutionary High-performance High-quality Sensor with Built-in Amplifier can be adjusted in seconds because the optical axis coincides with the mounting
More informationBuilt-in Amplifier Photoelectric Sensor
Built-in Amplifier Photoelectric Sensor Easy-to-use, Low-cost Photoelectric Sensor Incorporating s that can be clearly seen from a distance Conforms to EN and IEC standards Incorporating polarizing function,
More informationDistance-setting Photoelectric Sensor
Distance-setting Photoelectric Sensor The Combination of the Hyper LED and Shine-proof Achieves both Ease-of-use and High Performance Hyper LED mounted. Finest pin-point beam in the industry allows detection
More informationBuilt-in Amplifier Photoelectric Sensor
Built-in Amplifier Photoelectric Sensor Easy-to-use, Low-cost Photoelectric Sensor Incorporating s that can be clearly seen from a distance Conforms to EN and IEC standards Incorporating polarizing function,
More informationE3S-CR62/67. Ideal for detecting transparent glass and plastic containers. Transparent bottle sensor. Features
bottle sensor Ideal for detecting transparent glass and plastic containers Features Stable operation even if container interval is shortened for higher productivity. Stable detection of 5 mm gaps that
More informationZ4D-F. LED-type Micro Displacement Sensor with Many Features in a Compact Body. Micro Displacement Sensor. Ordering Information.
/ Length Micro Sensor LED-type Micro Sensor with Many Features in a Compact Body Compact body only /4th the volume of our previous product. % cost reduction over our previous product. High performance
More informationDistance-setting Photoelectric Sensor
Distance-setting Photoelectric Sensor The Combination of the Hyper LED and Shine-proof Achieves both Ease-of-use andhighperformance Hyper LED mounted. Finest pin-point beam in the industry allows detection
More informationParallel Beam Linear Sensor
Parallel Beam Linear Sensor Visible Red Class II Laser Width/Profile Measurement Sensor Providing High-Speed Precision Measurement with Flexible Operation H FDA Class II IEC Class 2 visible red laser ensures
More informationConnections Appearance Sensing method Sensing distance Operating mode Model Plug-in connector Horizontal Through-beam 30 m Light-ON
Heavy-duty Plug-in Photoelectric Sensor Water-resistive Photoelectric Sensor with Metal Housing & Plug-in Connector Ensuring Long Sensing Distance Satisfies the requirements of IP67, and NEMA6P. Ensures
More informationES Series Features Detecting distance twice that of conventional
Long-distance Separate-amplifier Series Features Detecting distance twice that of conventional sensors Detecting distance easily adjustable Wide range of sensor head types available Built-in alarm output
More informationAbsolute Rotary Encoder
Absolute Rotary Encoder Use the Tough (Rated IP64 for Degree of Protection) Combined with a PLC or Cam Positioner for Optimum Control and Ease-of-Use Incorporates a sealed bearing, meeting IP64 for durability
More informationLaser Photoelectric Sensor
Laser Photoelectric Sensor Prewired DC Sensor Provides Long- Distance Sensing of Objects as Small as 0.1 mm Detect small objects over longer sensing distances with highly accurate positioning Attachable
More informationLaser Photoelectric Sensor
Sensing Supply voltage Output Laser beam Laser beam 12-24 VDC ±10% 2 m, 10 m 20 to 50 m 80 ma Laser Photoelectric Sensor Prewired DC Sensor Provides Long-Distance Sensing of Objects as Small as 0.1 mm
More informationCM48 Series Vari-Angle IR Illuminator
CM48 Series Vari-Angle IR Illuminator Installation Guide Rev. 1.2 QIG Part no.: 625037102G Revision History: * Rev. 1.0: Initial Release * Rev. 1.1: Updated illumination range and beam angles. Added the
More informationGeneral-Purpose Photoelectric Sensor
General-Purpose Photoelectric Sensor Wide Selection of High Performance Small DC Sensors Offers Longer Sensing Distances Fast 0. msec response time for high-speed sensing Extended sensing distances up
More informationRota-Sonde DC4500. Smart display with Signal level. Easy alignment with Laser Line. Design for the most difficult applications
Scanning HOT METAL DETECTOR Rota-Sonde DC4500 Smart display with Signal level Easy alignment with Laser Line Design for the most difficult applications Very High Sensitivity 360 F Lt 1445 1 Applications
More informationLA-T SERIES. Fast and reliable minute granular flaw detection in winding wires. Winding Wire Granular Flaw Detector PARTICULAR USE SENSORS
SERIES Winding Wire Granular Flaw Detector Orders accepted till September, 2003 Production to be discontinued from April, 2004 Fast and reliable minute granular flaw detection in winding wires Slim Reliable
More informationCM80 Series Vari-Angle IR Illuminator
CM80 Series Vari-Angle IR Illuminator Installation Guide Rev. 1.1 QIG Part no.: 625040201G Revision History: * Rev. 1.0: Initial Release * Rev. 1.1: Added safety instructions and warning messages. Package
More informationManual for Hole Detectors PP
Manual for Hole Detectors PP2441... Page 1 General description Manufacturer: Fotoelektrik Pauly GmbH & Co. KG, Germany Type: PP2441(q)/ / One hole detector comprising (for each WPD): 1 - Transmitter PP2441(q)S/
More informationLINEAR LIGHT. LED Strobe Indicator ON = Light Active Green Indicator LED
product introduction LX150 Series Series LINEAR LIGHT Direct Connect The plug n play design of the Direct-Connect Linear Light Series gives users tremendous flexibility without the concern for additional
More informationMLV40 Series Miniature Sensors
MLV4 Series Miniature Sensors Diffuse Mode See page 54 Features: Adjustable sensitivity Complementary outputs Sensing Range: 5 mm Outputs: NPN, PNP Thru-Beam Mode See page 57 Rugged metal housing Compact
More information2 Registration Mark Photoelectric Sensors
High Resolution/High Speed Registration Mark Sensor 2 Registration Mark Photoelectric Sensors 2-131 Registration Mark Photoelectric Sensors 2 High Resolution/High Speed Registration Mark Sensor The Mark
More informationE3S-C. Built-in Amplifier Photoelectric Sensor. Water- and Oil-resistive Photoelectric Sensor with Metal Housing Ensuring Long Sensing Distance
Built-in Amplifier Photoelectric Sensor Water- and Oil-resistive Photoelectric Sensor with Metal Housing Ensuring Long Sensing Distance Satisfies the requirements of IP67, NEMA 6P, and IP67G (oil-tight).
More information10 to 30 VDC (10% max. permissable ripple peak-to-peak)
R Background Suppression Sensor Photoelectric Sensor With Adjustable Setting Distance in Rugged Metal Housing H Stable detection regardless of material color or size of sensing object: 2% or less black/white
More informationOperation Manual February Opticom Infrared System
Operation Manual February 2008 Opticom Infrared System M195/196, M9192, M292, M9592, M592 Emitters M511, M521, M522 Detectors M262, M562 Phase Selectors M360, M560 System Chassis M5168, M5575 Interface
More informationLaser Displacement Sensor Z4M. Ordering Information
Laser Displacement Sensor Compact Displacement Sensor with 1.5-micron Resolution Offers Long-distance Measurement for In-line Production Inspection High resolution with 3 user-selectable response speed
More informationHole-detection instruments Type series PP2441
Operating instructions Hole-detection instruments Type series PP2441 E_431x2 Characteristic features Application 1: Hole-marked weld seam or basted-seam detection Application 2: Pin-hole analysis in sheet
More informationHPA Series. Self-contained Photoelectric Controls with High Functions. Specifications CLICK FEATURES ORDER GUIDE. Pre-leaded type (2m lead)
6 HPA Series Specifications Self-contained Photoelectric Controls with Functions FEATURES Strobe Light Emission, Margin Regulation, Front Incoming Light Display, and Output Inhibit Functions Allow Sensing
More informationE3S-A/B. Built-in Amplifier Photoelectric Sensor. Ordering Information. Revolutionary High-performance High-quality Sensor with Built-in Amp
Built-in Amplifier Photoelectric Sensor Revolutionary High-performance High-quality Sensor with Built-in Amp can be adjusted in seconds because the optical axis coincides with the mounting axis. Highly
More informationPhotoelectric Sensor
Photoelectric Sensor Revolutionary High-performance High-quality Sensor with Built-in Amp can be adjusted in seconds because the optical axis coincides with the mounting axis. Highly visible spot on white
More informationSL Series Slot Sensor
Self-contained opposed-mode sensor pair Features An easy-to-use self-contained opposed-mode sensor pair in a rugged U-shaped housing Easy and economical to mount Molded-in beam guides simplify mounting
More informationonlinecomponents.com
Analog Photoelectric Sensor Analog Output Proportional to Light Received, Ideal For Inspection and Measurement Analog object detection ideal for position, size, color and surface characteristics Both analog
More informationPNP. 5 to 800 mm sensor to reflector distance on BRT-60x40C NPN
Datasheet Coaxial polarized retroreflective sensor for clear object detection Reliable detection of clear, translucent, or opaque objects including PET and glass containers, transparent films, and mirror-like
More informationE2B PROXIMITY SENSORS
Authorised Distributors:- Intech Systems Chennai Pvt. Ltd, Chennai-00 0 Ph: +9 8888 Fax: 0 7888 E-mail: info@intechchennai.com Website: www.intechchennai.com EB PROIMITY SENSORS A ne w g ener ation in
More informationUniversal Voltage Cabled Photoelectric E3JK
Universal Voltage Cabled Photoelectric Small Cable Sensor with Complementary Outputs Universal AC/DC supply voltage Relay or NPN/PNP transistor output, light-on or dark-on operation Polarized retroreflective
More information40 mm Beam Pitch General Purpose Area Sensor NA40 SERIES
9 0 mm Beam Pitch General Purpose Area Sensor SERIES Related Information General terms and conditions... F- Glossary of terms / General precautions...p.59~ / P.55~ guide... P.9~ Korea s S-mark... P.60
More informationPICO-AMP Miniature Remote Sensing System
PICO-AMP Miniature Remote Sensing System MD14 Modulated Amplifer and Ultra-small Remote Sensors PICO-AMP Features Ultra-small remote sensors to fit the tightest locations Three fixed frequency selections
More informationCZ-K Series. RGB Digital Fiberoptic Sensors. Description MAIN MENU PRODUCTS APPLICATIONS INDEX SELECTION GUIDE
RGB Digital Fiberoptic Sensors CZ-K Series Features RGB three-light source Wide detection range of 70 ±20 mm 2.75" ±0.78" High-speed response of 300 µs Water-resistant sensor head IP-67 rated Detecting
More information5-step-switch for adjustment of sensitivity (switching threshold) LED (super-bright, yellow) for switching state indication.
D-LAS Series D-LAS-24/90-ED-(16)-AC-T (Glass Pane Detection) - Collimated laser beam (
More information5-pole M12 connector. Connecting cable: cab-m12/5-g-2m. LED (red) for dirt accumulation indication
D-LAS Series D-LAS-34-ED-25x2-AC-T (Glass Pane Detection) - Collimated laser beam (
More informationLong Range Metal Body Sensor
R Long Range Metal Body Sensor 30 m Range With Advanced Fuzzy Logic H Mutual interference protection H NPN/PNP switch selectable output H M12 plug-in connector H Meets IP67 and NEMA 4X, 6P H Vibration
More informationSET Installation and Operating Instructions. Level switch for two sensors
Labkotec Oy Myllyhaantie 6 FI-33960 PIRKKALA FINLAND Tel: + 358 29 006 260 Fax: + 358 29 006 1260 20.2.2013 Internet: www.labkotec.fi 1/14 SET-2000 Level switch for two sensors Copyright 2013 Labkotec
More informationUltraminiature Photoelectric Switches with Self-contained Amplifier
Ultraminiature Photoelectric Switches with Self-contained Amplifier HPJ Series Fingertip-size, Provided with a various slit attachments. (six types) Fingertip-size 22 x 11 x 8 mm (thru scan model) 30 x
More informationWORLD-BEAM QS18AFF200 Sensors with Foreground Suppression
WORLD-BEAM QS8AFF00 Sensors with Foreground Suppression Datasheet Compact sensors featuring extended range and foreground suppression mode Exceptional optical performance; up to 00 mm sensing range in
More informationThree models available: Relay output with 24 VDC power input Relay output with 85 to 250 VAC power input Solid-state output with 24 VDC power input
Cperimeter access guarding Description Explosion Proof BeamSafe Long-ange, Single-Beam Safety Control 4 m (40 ft.) range Four possible transmit codes eliminate crosstalk from multiple units in the same
More informationZ500. High-Precision Sensor that Measures and Displays an Object's Profile. Profile Measuring System
Profile Measuring System High-Precision Sensor that Measures and Displays an Object's Profile. Features OMRON's original line beam method provides a complete solution to profile measurement problems. Conventional
More informationLED Displacement Sensor
LED Displacement Sensor Low-cost LED Displacement Sensor Offers 10-micron Resolution of 25 mm (0.98 in) with measurement range of ±4 mm (0.16 in). Easy-to-use, built-in amplifier. Fast 5-millisecond response.
More informationLX Series Part-Sensing Light Screen
Datasheet For Sensing Small or Flat Parts at High Speeds Emitter and receiver pair produce a strobed web of modulated light beams, in 8 lengths, 2 sensing ranges Simple, economical and highly reliable
More informationE3S-CL. Distance setting photoelectric sensor in metal housing. Features
Distance setting photoelectric sensor in metal housing High water, oil and detergent resistance Minimal black/white error for highest reliability detecting different colored objects () Features Eliminates
More informationseries. Safety sensor for Palletisers. Features. For Palletiser. 3 Different types available. Active - Passive system and Plug and play
Safety sensor for Palletisers Features For Palletiser has been developed especially for Palletisers and wrapping machine access protection applications. Active - Passive system and Plug and play By using
More informationSpecifications. Environmental. Operating Temperature [C (F)] for TRIAC output ( ) for all others
Specifications Environmental Line Line Green Line Analog ertifications UL Listed, SA Approved, and E Marked for all applicable directives Features S Wide selection for increased application flexibility
More informationE3X-NL. Employs OMRON's Unique Free Angle Optics Technology for Detecting Minute Differences in Glossiness. Optical Fiber Glossy Object Sensor
Authorised Distributors:- AS & AAIN INDIA PVT TD S-1, F.I.E.E., Okhla Industrial Area, Phase-ii, New Delhi-112(India) Tel : 11-43797575 Fax : 11-43797574 E-mail : sales@ashalain.com Fiber Glossy Object
More informationInstallation Instructions for Zip Suspension Downlight with Remote Power and 4" Square or Round Canopy
Doc # 90-ZS-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Zip Suspension Downlight
More informationInstruction Manual. X4 Bar 20. from software version: v
Instruction Manual X4 Bar 20 from software version: v0.26 support@glp.de www.glp.de Contents 1 Description of Device... 3 1.1 Safety Instructions... 4 2 Preparation and Installation... 5 2.1 Safety Information...
More informationCONTENTS OF THE BOX. *PIR sensor only **Dual Technology and PIR sensors only. Description PIR Ultrasonic Dual Technology
Instruction Bulletin 63249-420-283A4 08/2009 Wall Mount Occupancy Sensor SLSWPS1500, SLSWUS1500, SLSWDS1500 INTRODUCTION Wall Mounted Occupancy Sensors are Class 2 devices ideal for use in business or
More informationOperating instructions optical fork sensor OPU200 OPU200 / / 2018
Operating instructions optical fork sensor OPU200 OPU200 / 0 08 / 208 Contents Preliminary note.... Symbols used... 2 Functions and features... Installation... 4 Operating and display elements... 5 Electrical
More informationSensing method Appearance Sensing distance Operation mode Model. Emitter E3S-2LE4 Through-beam *1. 2 m. 0.1 to 2 m. 300 mm. 2 m
Photoelectric Sensor with Built-in Amplifier CSM DS_E 1 General-purpose Photoelectric Sensor for High Quality and Reliable Detection Be sure to read Safety Precautions on page 8. Ordering Information General-purpose
More informationFST Series HUMIDITY-TEMPERATURE TRANSMITTERS INSTRUCTION MANUAL
FST Series HUMIDITY-TEMPERATURE TRANSMITTERS INSTRUCTION MANUAL 20020628 CONTENTS DESCRIPTION... 3 OPERATION... 4 Power Supply...4 Output Range...4 Temperature Operating Range and Temperature Limits...4
More informationCollimated Backlights BL-CL
The Collimated Backlight Series is a high performance, uniform, and collimated light source for high precision silhouetting and transmissive applications. Using precision optics, these lights are collimated
More informationCylindrical Photoelectric Sensor. 6. Connection F Sensing Distance. 100: 100 mm. 300: 300 mm 2M: 2 Meters 5M: 5 Meters. 5. Output NPN - NO, NC
Cylindrical Sensor Proximity SALIENT FEATURES Metal Housing AC 2wire- NO, NC DC 3 Wire- NPN, PNP DC Dual Output Models Upto 5 m sensing distance Diffuse, Retro, Through Beam Measurement Model Number Legend
More informationCA80 Series Vari-Angle IR Illuminator
CA80 Series Vari-Angle IR Illuminator Installation Guide Rev. 1.0 QIG Part no.: L625000100G 100% 75% 50% 25% Dimming Zoom LED On/Off LED Status 50% 20% 10% Revision History: * Rev. 1.0: Initial Release
More informationInstruction Manual. X4 Bar 10. from software version: v
Instruction Manual X4 Bar 10 from software version: v0.26 support@glp.de www.glp.de Contents 1 Description of Device... 3 1.1 Safety Instructions... 4 2 Preparation and Installation... 5 2.1 Safety Information...
More informationSensing method Through-beam Retroreflective Diffuse reflective Convergent-beam Appearance Side-view Flat Side-view Flat Side-view
R Subminiature Photoelectric Sensor Omron s Next Generation of Sub-miniature Photoelectric Sensors H Utilizes Omron s Hyper LED technology to achieve the industry s smallest visible red beam H Self-contained
More informationSensing method Through-beam Retroreflective Diffuse reflective Convergent-beam Appearance Side-view Flat Side-view Flat Side-view
R Subminiature Photoelectric Sensor Omron s Next Generation of Sub-miniature Photoelectric Sensors H Utilizes Omron s Hyper LED technology to achieve the industry s smallest visible red beam H Self-contained
More informationFlow Detection MDS Integral or Remote Housing. Installation and Operating Instructions
Flow Detection MDS Integral or Remote Housing Solids - Chute and Conveyor 10.525 GHz Sender Receiver Installation and Operating Instructions Measurement Systems INTRODUCTION CONTENTS PROPRIETARY NOTICE
More informationCompact Sensors - S8 Series. Compact size and high performance for the most challenging detection applications
Compact size and high performance for the most challenging detection applications Compact dimensions (14x42x25 mm) Background suppression for transparent and shiny objects High speed contrast sensor up
More informationFuzzy Temperature Controllers E5AF
Fuzzy Temperature Controllers 1/4 DIN Controller Combines Fuzzy and PID Control For Fast Response to Process Disturbances Advanced PID control provides optimal response during start-up and steadystate
More informationCompact Sensors - S8 Series. Compact size and high performance for the most challenging detection applications
Compact size and high performance for the most challenging detection applications Compact dimensions (14x42x25 mm) Background suppression for transparent and shiny objects High speed contrast sensor up
More informationCompact Sensors - S8 Series. Compact size and high performance for the most challenging detection applications
Compact size and high performance for the most challenging detection applications Compact dimensions (14x42x25 mm) Background suppression for transparent and shiny objects High speed contrast sensor up
More informationLong Range Metal Body Sensor
R Long Range Metal Body Sensor 30 m Range With Advanced Fuzzy Logic H Mutual interference protection H NPN/PNP switch selectable output H M12 plug-in connector H Meets IP67 and NEMA 4X, 6P H Vibration
More informationPD30CNB25xxPS. Photoelectrics, Background suppression reflective - PointSpot. Main features. Main functions. Description
Photoelectrics, Background suppression reflective - PointSpot Main features Miniature sensor range The visible red PointSpot light makes alignment very easy Range: 250 mm Sensitivity adjustment by potentiometer
More informationSensing method Appearance Sensing distance Operation mode Model Convergent-reflective (narrow vision field) 30 to 100 mm (variable)
Photoelectric Sensor with Built-in Amplifier CSM DS_E_11_1 General-purpose Photoelectric Sensor for High Quality and Reliable Detection Be sure to read Safety Precautions on page 8. Note: -2/-/-DS10/-DS30/-R2
More informationF3SJ-B. Safety Light Curtain. Basic Type with a combination of performance and functionality. Ordering Information. Main Units Safety Light Curtain
Safety Light Curtain 3SJ- asic Type with a combination of performance and functionality Up to three sets of series-connected sensors. The muting function is enabled simply with Muting Key Cap. Comes standard
More informationGlossary of terms... P.1549~ General precautions... P panasonic.net/id/pidsx/global
0 PHOTO PHOTO MEASURE Light Curtain Type SERIES Ver. Related Information Category PLc SIL General terms and conditions... F- SF-C/C...P.~ Type safety solution International regulations for safety measures
More informationSpecifications. Environmental. Operating Temperature [C (F)] for TRIAC output ( ) for all others
Specifications Environmental Line Line Green Line Analog ertifications UL Listed, SA Approved, and E Marked for all applicable directives Features S Wide selection for increased application flexibility
More informationInstallation, Operation and Maintenance Manual
TM M723 Rev. C Model 1050 Strain Gage Transmitter Installation, Operation and Maintenance Manual Table of Contents General... 1 Installation... 1 Specifications... 1 Wiring... 2 Setup and Operation...
More informationE3Z-LS. Distance-settable Photoelectric Sensor. Ordering Information. Sensors. Accessories (Order Separately)
Distance-settable Photoelectric Sensor Switching between background and foreground suppression (BGS/FGS) enables detecting a variety of objects under various background/foreground conditions. Influence
More informationA-GAGE MINI-ARRAY. Two-Piece Measuring Light Screen. Instruction Manual. Features
Features Simple two-piece measuring light screen for inspection, profiling, and object detection, tailored for vehicle separation applications. Detects single-fault emitter, receiver and dirty lens conditions;
More informationNA DigiParts GmbH. Small / Slim Object Detection Area Sensor
953 PHOTO PHOTO MEASURE ITY Object Area Sensor General terms and conditions... F-7 Related Information Glossary of terms... P.1455~ Cross-beam scanning system to detect slim objects Letters or business
More informationIS-3000 SERIES INFRARED SCANNER
IS-3000 SERIES INFRARED SCANNER NON-CONTACT, RELIABLE, PRECISE, LONG RANGE POSITIONING FOR HOT OR COLD PRODUCTS FEATURES ANALOG AND DIGITAL OUTPUTS INDICATIVE OF TARGET POSITION, WIDTH AND TEMPERATURE
More informationpanasonic-electric-works.net/sunx Type 2 safety solution International regulations for safety measures at reasonable cost
99 PHOTO PHOTO Curtain Type SERIES Ver. Related Information Ver. General terms and conditions... F- Glossary of terms / General precautions...p.9~ / P.0 selection guide...p.~ SF-C0... P.~ Conforming to
More informationINSTALLATION AND OPERATION MANUAL
Version 2.2 MS1016 MTF SERIES VIBRATING PROBES FOR LIQUIDS AND HYC-PKK-312 SWITCHING ISOLATOR INSTALLATION AND OPERATION MANUAL Hycontrol Limited, Larchwood House, Orchard Street, Redditch, Worcestershire,
More informationSLE30 Expert Series Teach-Mode Slot Sensor
SLE30 Expert Series Teach-Mode Slot Sensor Self-contained opposed-mode sensor pair with Teach Mode SLE30 Expert Series Slot Sensor Features An easy-to-use, self-contained opposed-mode sensor pair in a
More informationInstallation Instructions PHOTOSWITCH Series 9000 On/Off and Timing Photoelectric Sensors
Installation Instructions PHOTOSWITCH Series 9000 On/Off and Timing Photoelectric Sensors All Sensors Retroreflective Polarized Retroreflective ClearSight TM Standard Diffuse Long Range Diffuse Extended
More informationNA1-11. Small / Slim Object Detection Area Sensor. Cross-beam scanning system to detect slim objects. Letters or business cards detectable!
891 Object Area Sensor General terms and conditions... F-17 Related Information Glossary of terms... P.1359~ Sensor selection guide...p.831~ General precautions... P.1405 PHOTO PHOTO Conforming to EMC
More informationSENSORS S62. Compact Sensors - S62. The most complete universal sensor in a compact 50x50 mm housing. Sensors with red, infrared LED or LASER emission
Compact Sensors - S6 S6 The most complete universal sensor in a compact x housing Sensors with red, infrared or LASER emission from 3 cm to m Polarized retroreflective up to 0 m Multivoltage 4-40Vac/4-60Vdc
More informationRead this user s manual before use to ensure proper operation. Keep the manual on hand for reference in case there is a problem.
LD3500 Series CONTENTS Read this user s manual before use to ensure proper operation. Keep the manual on hand for reference in case there is a problem. Warranty lnformation Maintenance Exploded View Features
More informationPhotoelectric Switches for Harsh Environments
Photoelectric Switches for Harsh Environments HP8 Series For even harsher environments Die-cast housing for strength and shock resistance High-performance seal Resistance to the most advanced cutting oils
More informationSafe red LED beam. Span & shift adjustment. Light beam. Receiver. Emitter. Sensing object. Darkest condition 1.00 V 1.49 V Setting condition 2.
LA- SERIES LED Collimated Beam Sensor LA LA- HL-T1 LM1 LH-5 HL-C1 Compact size Its emitter and receiver are much smaller compared to those of the amplifier built-in type (LA-51). Hence, they can be installed
More informationLong-distance Separate-amplifier Proximity Sensors ES Series Features Detecting distance twice that of conventional
Long-distance Separate-amplifier ES Series Features Detecting distance twice that of conventional sensors Detecting distance easily adjustable Wide range of sensor head types available Built-in alarm output
More informationMineral-insulated resistance thermometers to EN
Data Sheet 90.2221 Page 1/6 Mineral-insulated resistance thermometers to EN 60 751 for temperatures from -50 (-200) to +600 C flexible sheath with shock-protected sensor as single or twin resistance thermometer
More informationProduct description. At a glance. performance in a metal housing coating available Precise autocollimation optics. sensors
W- Laser Small photoelectric sensors W High-performance photoelectric sensor family with laser optics Product description At a glance performance in a metal housing coating available Precise autocollimation
More informationFEATURES. 15 m ft. 4 m ft. 2 m ft. 100 mm in. 600 mm in. 15 m ft. 4 m ft. 2 m ft. 100 mm 3.
273 Cylindrical Photoelectric Sensor SERIES Related Information General terms and conditions... F-3 Glossary of terms... P.1549~ guide... P.231~ General precautions... P.1552~ PHOTO PHOTO MEASURE -LS200
More informationInstallation Instructions PHOTOSWITCH Series 9000 On/Off and Timing Photoelectric Sensors
Installation Instructions PHOTOSWITCH Series 9000 On/Off and Timing Photoelectric Sensors Polarized Transmitted Beam Fiber Optic All Sensors Retroreflective Retroreflective ClearSight TM Standard Diffuse
More informationLD8000 Series LD8025 LD8050 LD8100
LD8000 Series LD8025 LD8050 LD8100 CONTENTS Read this user s manual before use to ensure proper operation. Keep the manual on hand for reference in case there is a problem. Warranty Information Maintenance
More informationELECTRONIC REGULATOR FOR OPEN LOOP
Characteristics SINGLE CHANNEL DUAL CHANNEL 12 VDC / 24 VDC ± 10% Feeding voltage (stabilized) 12 VDC / 24 VDC ± 10% 10 30 VDC Feeding voltage (max) 10 30 VDC 40 W Max power absorption 40 W 2.8 A Output
More informationContents. Volume 8 Sensing Solutions CA E February
Photoelectric Sensors.9 Product Description The E67 Long Range Perfect Prox Series from Eaton s electrical sector, the highest performing long-range sensor you can buy with background rejection, is ideal
More information