Test Report. Product Name : PC2PC-Bluetooth Model No. : MS Date of Receipt : Apr. 22, Date of Test : May 09, Report No.

Transcription

1 Report No. 024L064E Test Report Product Name : PC2PC-Bluetooth Model No. : MS-6967 Applicant : MICRO-STAR INT'L Co., LTD. Address : No. 69, Li-De St, Jung-He City, Taipei Hsien, Taiwan, R.O.C. Date of Receipt : Apr. 22, 2002 Date of Test : May 09, 2002 Report No. : 024L064E The Test Results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Page : 1 of 45

2

3 Report No. 024L064E Description TABLE OF CONTENTS Page 1. GENERAL INFORMATION EUT Description Tested System Details Configuration of Tested System EUT Exercise Software Test Facility Conducted Emission Test Equipment List Test Setup Limits Test Procedure Test Specification Test Result Radiated Emission Test Equipment Test Setup Limits Test Procedure Test Specification Test Result Electrostatic Discharge (ESD) Test Equipment Test Setup Test Level Test Procedure Test Specification Test Result Radiated Susceptibility (RS) Test Equipment Test Setup Test Level Test Procedure Test Specification Test Result Electrical Fast Transient/Burst (EFT/B) Test Equipment Test Setup Test Level Test Procedure Test Specification Test Result...18 Page : 3 of 45

4 Report No. 024L064E 7. Surge Test Equipment Test Setup Test Level Test Procedure Test Specification Test Result Conducted Susceptibility (CS) Test Equipment Test Setup Test Level Test Procedure Test Specification Test Result Voltage Dips and Interruption Measurement Test Equipment Test Setup Test Level Test Procedure Test Specification Test Result EMC Reduction Method During Compliance Testing Test Result Test Data of Conducted Emission Test Data of Radiated Emission Test Data of Electrostatic Discharge Test Data of Radiated Susceptibility Test Data of Electrical Fast Transient Test Data of Surge Test Data of Conducted Susceptibility Test Data of Voltage Dips and Interruption...43 ATTACHMENT 1: EUT TEST PHOTOGRAPHS ATTACHMENT 2: EUT DETAILED PHOTOGRAPHS REFERENCE : LABORATORY OF LICENSE Page : 4 of 45

5 Report No. 024L064E 1. GENERAL INFORMATION 1.1. EUT Description Product Name : PC2PC-Bluetooth Trade Name : MICRO-STAR Model No. : MS-6967 Frequency Range : 2402MHz to 2480MHz Channel Number : 79 Type of Modulation : Frequency Hopping Spread Spectrum Antenna Type : Connector Antenna Cable : Shielded, 0.3m Working Frequency of Each Channel: Channel Frequency Channel Frequency Channel Frequency Channel Frequency Channel 00: 2402 MHz Channel 01: 2403 MHz Channel 02: 2404 MHz Channel 03: 2405 MHz Channel 04: 2406 MHz Channel 05: 2407 MHz Channel 06: 2408 MHz Channel 07: 2409 MHz Channel 08: 2410 MHz Channel 09: 2411 MHz Channel 10: 2412 MHz Channel 11: 2413 MHz Channel 12: 2414 MHz Channel 13: 2415 MHz Channel 14: 2416 MHz Channel 15: 2417 MHz Channel 16: 2418 MHz Channel 17: 2419 MHz Channel 18: 2420 MHz Channel 19: 2421 MHz Channel 20: 2422 MHz Channel 21: 2423 MHz Channel 22: 2424 MHz Channel 23: 2425 MHz Channel 24: 2426 MHz Channel 25: 2427 MHz Channel 26: 2428 MHz Channel 27: 2429 MHz Channel 28: 2430 MHz Channel 29: 2431 MHz Channel 30: 2432 MHz Channel 31: 2433 MHz Channel 32: 2434 MHz Channel 33: 2435 MHz Channel 34: 2436 MHz Channel 35: 2437 MHz Channel 36: 2438 MHz Channel 37: 2439 MHz Channel 38: 2440 MHz Channel 39: 2441 MHz Channel 40: 2442 MHz Channel 41: 2443 MHz Channel 42: 2444 MHz Channel 43: 2445 MHz Channel 44: 2446 MHz Channel 45: 2447 MHz Channel 46: 2448 MHz Channel 47: 2449 MHz Channel 48: 2450 MHz Channel 49: 2451 MHz Channel 50: 2452 MHz Channel 51: 2453 MHz Channel 52: 2454 MHz Channel 53: 2455 MHz Channel 54: 2456 MHz Channel 55: 2457 MHz Channel 56: 2458 MHz Channel 57: 2459 MHz Channel 58: 2460 MHz Channel 59: 2461 MHz Channel 60: 2462 MHz Channel 61: 2463 MHz Channel 62: 2464 MHz Channel 63: 2465 MHz Channel 64: 2466 MHz Channel 65: 2467 MHz Channel 66: 2468 MHz Channel 67: 2467 MHz Channel 68: 2470 MHz Channel 69: 2471 MHz Channel 70: 2472 MHz Channel 71: 2473 MHz Channel 72: 2474 MHz Channel 73: 2475 MHz Channel 74: 2476 MHz Channel 75: 2477 MHz Channel 76: 2478 MHz Channel 77: 2479 MHz Channel 78: 2480 MHz Note: 1. This device is a 2.4GHz bluetooth device included a 2.4GHz receiving function, and 2.4GHz transmitting function for the headset of cellular. Frequency hopping device with 79 hopping channels. 2. Mode 1: Data Transmit Mode 2: Data Receive Page : 5 of 45

6 Report No. 024L064E 1.2. Tested System Details The types for all equipment, plus descriptions of all cables used in the tested system (including inserted cards ) are: Product Manufacturer Model No. Serial No. (1) PC Mother Board CPU HDD FDD CD-ROM Bluetooth Card (EUT) Switch Power Supply MICRO-STAR INTEL Quanturn Panasoinc TEAC MICRO-STAR ASTEC MS-6580 Pentium 4,1.9GHz/100MHz Fireball JU-257A6069C CD-532E MS-6967 SA A N/A N/A N/A N/A N/A N/A (2) Monitor ADI CM T A (3) Keyboard HP SK-2506 C (4) Mouse IBM M-SAU-IBM (5) Joystick GENIUS MAXFIRE FORCE G-09D CJ (6) USB Video Camera Logitech V-UB2 LZA (7) USB Video Camera Logitech V-UB2 LZA (8) Microphone & Earphone TOKTO SX-MI N/A (9) Walkman AIWA HS-TA164 N/A (10) Modem ACEEX DM (11) Printer EPSON Color (12) Notebook DELL PP01L N/A Note: 1. The power cord of the device 1,2,10,11 and 12 are Non-shielded power cord. Signal Cable Type Signal cable Description A. VGA Cable Shielded, 1.6m, a ferrite core bonded B. Joystick Cable Shielded, 1.8m C. Keyboard Cable Shielded, 1.8m D. Mouse Cable Shielded, 1.2m E. LAN Cable Non-shielded, 3.0m F. Printer Cable Shielded, 1.6m G. Modem Cable Shielded, 1.6m H. Walkman Cable Non-shielded, 1.2m I. Microphone & Earphone Cable Non-shielded, 1.6m J. CCD Cable Shielded, 1.8m, a ferrite core bonded K. CCD Cable Shielded, 1.8m, a ferrite core bonded L. Antenna Cable Shielded, 0.3m, 2pcs. Page : 6 of 45

7 Report No. 024L064E 1.3. Configuration of Tested System A B C D G J F E Monitor (2) PC (1) EUT L Printer (11) Ant K Joystick (5) CCD (6) I CCD (7) H Keyboard (3) Mouse (4) Microphone &Earphone(8) Walkman (9) Modem (10) Notebook (12) EUT L Server Ant 1.4. EUT Exercise Software 1. Setup the EUT and simulators as shown on Turn on the power of all equipment. 3. PC reads data from disk. 4. Data will be transmitting and receiving through EUT. 5. The transmitted and receive status will be shown on the monitor. 6. Repeat the above procedure 4 to 5. Page : 7 of 45

8 Report No. 024L064E 1.5. Test Facility Ambient conditions in the laboratory: Items Required (IEC 68-1) Actual Temperature ( C) Humidity (%RH) Barometric pressure (mbar) Site Description: June 30, 2002 Accreditation on NVLAP NVLAP Lab Code: June 11, 2001 Accreditation on DNV Statement No. : LAB11 May 03, 2001 Accreditation on TUV Rheinland Certificate No.: I April 24, 2001 Accreditation on Nemko Certificate No.: ELA 165 Certificate No.: ELA 162 Certificate No.: ELA 191 Site Name: Site Address: Quietek Corporation No. 5, Ruei-Shu Valley, Ruei-Ping Tsuen, Lin-Kou Shiang, Taipei, Taiwa, R.O.C. TEL : / FAX : service@quietek.com Page : 8 of 45

9 Report No. 024L064E 2. Conducted Emission 2.1. Test Equipment List The following test equipment are used during the conducted emission test: Item Instrument Manufacturer Type No./Serial No Last Cal. Remark 1 Test Receiver R & S ESCS 30/838251/0001 May, L.I.S.N. R & S ESH3-Z5/836679/0023 May, 2002 EUT 3 L.I.S.N. R & S ENV 4200/833209/0023 May, 2002 Peripherals 4 Pulse Limiter R & S ESH3-Z2 N/A 5 No.4 Shielded Room N/A Note: All equipment upon which need to calibrated are with calibration period of 1 year Test Setup Reference Plane Test Receiver 40cm 12dBuV Load EUT LISN LISN Ground Plane LISN 2.3. Limits Frequency Limits (dbµv) (MHz) QP AV NOTE:1) The limit decreases linearly with the logarithm of frequency in the range 0.15MHz to 0.5MHz. 2) In the above table, the tighter limit applies at the band edges. Page : 9 of 45

10 2.4. Test Procedure The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50 ohm /50uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination. (Please refers to the block diagram of the test setup and photographs.) Both sides of AC line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ETS : ( ) on conducted measurement. The bandwidth of the field strength meter (R & S Test Receiver ESCS 30) is set at 9kHz Test Specification According to ETS :1997 ( ) EN 55022: Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 11. The acceptance criterion was met and the EUT passed the test. Page : 10 of 45

11 3. Radiated Emission 3.1. Test Equipment The following test equipment are used during the Radiated emission test: Test Site Equipment Manufacturer Model No./Serial No. Last Cal. Site # 1 Test Receiver R & S ESVS 10 / /003 July, 2001 Spectrum Analyzer Advantest R3162/ May, 2002 Pre-Amplifier Advantest BB525C/ 3307A01812 May, 2002 Bilog Antenna SCHAFFNER CBL6112B / 2697 Nov., 2001 Site # 2 Test Receiver R & S ESCS 30 / / 022 Nov., 2001 Spectrum Analyzer Advantest 3162 / May, 2002 Pre-Amplifier Advantest BB525C/3307A01814 May, 2002 Bilog Antenna SCHAFFNER CBL6112B / 2705 Oct., 2001 Horn Antenna ETS 3115 / July, 2001 Pre-Amplifier QTK QTK-AMP-01/ 0001 July, 2001 Site # 3 Test Receiver R & S ESI 26 / / 004 May, 2002 Spectrum Analyzer Advantest 3162 / May, 2002 Pre-Amplifier QTK QTK-AMP-03 / 0003 May, 2002 Bilog Antenna SCHAFFNER CBL6112B / 2697 May, 2002 Horn Antenna ETS 3115 / July, 2001 Pre-Amplifier QTK QTK-AMP-01 / 0001 July, 2001 Note: 1. All equipments that need to calibrate are with calibration period of 1 year. 2. Mark X test instruments are used to measure the final test results Test Setup 10m FRP Dome 1m to 4m Non-Conducted Table Load EUT Antenna Mast Dipole or Horn Antenna Antenna height can be moved from 1m to 4m, Antenna and turntable distance 10m 80cm Test Receiver Fully Soldered Ground Plane TO Controller To Receiver Radiated Emissions Page : 11 of 45

12 3.3. Limits Frequency (MHz) Distance (m) Limits (dbuv/m) Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 10 meters.the antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated according to EN :1997 on radiated measurement. Broadband antenna (calibrated bi-log and horn antenna) are used as a receiving antenna. Both horizontal and vertical polarization of the antenna are set on measurement. And a high frequency preamlifier were used increase the sensitivity of the measuring. In order to find the maximum emission, all of the interface cables must be manipulated according to I-ETS : ( ) on radiated measurement. The additional motch filter below 1GHz was used to measure the level of harmonics radiated emission during field dtrength of harmonics measurement. The bandwidth below 1GHz setting on the field strength meter (R&S Test Receiver ESCS 30 )is 120 khz, and 1MHz bandwidth is adpted above 1GHz. The frequency range from 30MHz to 10 th harmonics is checked Test Specification According to ETS : ( ) EN 55022: Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 11. The acceptance criterion was met and the EUT passed the test. Page : 12 of 45

13 4. Electrostatic Discharge (ESD) 4.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration 1 ESD Simulator System KeyTek ME-15/EC S/N: June Horizontal Coupling QuieTek HCP AL50 Plane(HCP) June Vertical Coupling VCP AL50 QuieTek Plane(VCP) June No.3 Shielded Room N/A Note: All equipment upon which need to calibrated are with calibration period of 1 year Test Setup Vertical Coupling Plane Insulation EUT Loads: Active Horizontal Coupling Plane 80cm Non-Conducted table ESD Simulator 470K ohm Resistor Metal Ground Plane 470K ohm Resistor 4.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria Enclosure Port Electrostatic Discharge kv(charge Voltage) ±8 Air Discharge ±4 Contact Discharge B Page : 13 of 45

14 4.4. Test Procedure Direct application of discharges to the EUT: Contact discharge was applied only to conductive surfaces of the EUT. Air discharges were applied only to non-conductive surfaces of the EUT. During the test, it was performed with single discharges. For the single discharge time between successive single discharges will be keep longer 1 second. It was at least ten single discharges with positive and negative at the same selected point. The selected point, which was performed with electrostatic discharge, was marked on the red label of the EUT. Indirect application of discharges to the EUT: Vertical Coupling Plane (VCP): The coupling plane, of dimensions 0.5m x 0.5m, is placed parallel to, and positioned at a distance 0.1m from, the EUT, with the Discharge Electrode touching the coupling plane. The four faces of the EUT will be performed with electrostatic discharge. It was at least ten single discharges with positive and negative at the same selected point. Horizontal Coupling Plane (HCP): The coupling plane is placed under to the EUT. The generator shall be positioned vertically at a distance of 0.1m from the EUT, with the Discharge Electrode touching the coupling plane. The four faces of the EUT will be performed with electrostatic discharge. It was at least ten single discharges with positive and negative at the same selected point Test Specification According to EN : Test Result The measurement of the electrostatic discharge was investigated and test result was shown in section 11. The acceptance criterion was met and the EUT passed the test. Page : 14 of 45

15 5. Radiated Susceptibility (RS) 5.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration 1 Signal Generator IFR 2023B / /581 May, Power Amplifier A & R 500A100AM3 /29369 Aug., Power Amplifier SCHAFFNER CBA9413B / 0006 June, Field Strength Sensor SCHAFFNER EMC 20 / Y-0028/ Z-0003 June, Power Antenna SCHWARZBECK VULB 9166 / 1073 Sep., Power Meter BOONTON 4232A / May, No.2 EMC Fully Chamber July, 2001 Note: All equipment upon which need to calibrated are with calibration period of 1 year Test Setup Antenna Mast 3 m Sensor Full-Anechoic Chamber Camera system EUT Load 1m 80cm Power Amplifier Field Meter Power Meter Signal Generator Computer controller Camera Monitor 5.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria Enclosure Port Radio-Frequency Electromagnetic Field Amplitude Modulated MHz V/m(Un-modulated, rms) % AM (1kHz) A Page : 15 of 45

16 5.4. Test Procedure The EUT and load, which are placed on a table that is 0.8 meter above ground, are placed with one coincident with the calibration plane such that the distance from antenna to the EUT was 3 meters. Both horizontal and vertical polarization of the antenna and four sides of the EUT are set on measurement. In order to judge the EUT performance, a CCD camera is used to monitor EUT screen. All the scanning conditions are as follows: Condition of Test Remarks 1. Field Strength 3 V/m Level 2 2. Radiated Signal AM 80% Modulated with 1kHz sinusoidal audio signal 3. Scanning Frequency 80MHz MHz 4 Dwell Time 2.86 Seconds 5. Frequency step size f : 1% 6. The rate of Swept of Frequency 1.5 x 10-3 decades/s 5.5. Test Specification According to EN : Test Result The measurement of the radiated susceptibility was investigated and test result was shown in section 11. The acceptance criterion was met and the EUT passed the test. Page : 16 of 45

17 6. Electrical Fast Transient/Burst (EFT/B) 6.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration 1 Fast Transient/Burst SCHAFFNER BEST Jun., 2001 Generator S/N: SC 2 No.3 Shielded Room N/A Note: All equipment upon which need to calibrated are with calibration period of 1 year Test Setup Ground AC Power Line to Personal Compute EFT/Burst Generator Coupling Clamp EUT Load Non-Conducted Table 80cm 6.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria Signal Ports and Telecommunication Ports Fast Transients Common Mode Input DC Power Ports Fast Transients Common Mode Input AC Power Ports Fast Transients Common Mode kv (Peak) Tr/Ts ns Rep. Frequency khz kv (Peak) Tr/Ts ns Rep. Frequency khz kv (Peak) Tr/Ts ns Rep. Frequency khz / / /50 5 B B B Page : 17 of 45

18 6.4. Test Procedure The EUT and load are placed on a table that is 0.8 meter above a metal ground plane measured 1m*1m min. and 0.65mm thick min. And projected beyond the EUT by at least 0.1m on all sides. For Signal Ports and Telecommunication Ports: The EFT interference signal is through a coupling clamp device couples to the signal and control lines of the EUT with burst noise for 1min. For Input DC and AC Power Ports: The EUT is connected to the power mains through a coupling device that directly couples the EFT interference signal. Each of the Line and Neutral conductors is impressed with burst noise for 1 min. The length of power cord between the coupling device and the EUT shall be 1m Test Specification According to EN : Test Result The measurement of the Electrical Fast Transient/Burst was investigated and test result was shown in section 11. The acceptance criterion was met and the EUT passed the test. Page : 18 of 45

19 7. Surge 7.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration 1 Surge Generator SCHAFFNER BEST Jun., 2001 S/N: SC 2 No.3 Shielded Room N/A Note: All equipment upon which need to calibrated are with calibration period of 1 year Test Setup PC Surge Generator EUT Load Non-Conducted Table Non-Conducted Table 7.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria AC Input and AC Output Power Ports Surges Line to Line Line to Ground Tr/Ts us kv kv 1.2/50 (8/20) ± 0.5 ± 1 Notes: 1) Applicable only to ports which according to the manufacturer s may directly to outdoor cables. 2) Where normal functioning cannot be achieved because of the impact of the CDN on the EUT,no test shall be required. B Page : 19 of 45

20 7.4. Test Procedure The EUT and its load are placed on a table that is 0.8 meter above a metal ground plane measured 1m*1m min. and 0.65mm thick min. And projected beyond the EUT by at least 0.1m on all sides. The length of power cord between the coupling device and the EUT shall be 2m or less. For Input and Output AC Power or DC Input and DC Output Power Ports: The EUT is connected to the power mains through a coupling device that directly couples the Surge interference signal. The surge noise shall be applied synchronized to the voltage phase at 0 0, 90 0, 180 0, and the peak value of the a.c. voltage wave. (Positive and negative) Each of Line-Earth and Line-Line is impressed with a sequence of five surge voltages with interval of 1 min Test Specification According to EN : Test Result The measurement of the Surge was investigated and test result was shown in section 11. The acceptance criterion was met and the EUT passed the test. Page : 20 of 45

21 8. Conducted Susceptibility (CS) 8.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration 1 Signal Generator IFR 2023B / /581 May, Power Amplifier A & R 500A100AM3 /29369 Aug., Power Amplifier SCHAFFNER CBA9413B / 0006 June, CDN 1 Schwarzbeck L801 M2/3 / 1549 June, CDN 2 Schwarzbeck L801 S1 / 1574 June, CDN 3 Schwarzbeck L801 AF4 / 1064 June, CDN 4 Schwarzbeck L801 AF8 / 1070 June, CDN 5 FCC FCC-801-S9 / 9837 June, CDN 6 FCC FCC-801-S15 / 9838 June, CDN 7 FCC FCC-801-S25 / 9839 June, ohm Terminator RES-NET RCX6BM June, dB Attenuator BIRD RFA250NFF10 June, EM Clamp Schwarzbeck KEMZ 801 / June, No.2 EMC Fully Chamber N/A Note: All equipment upon which need to calibrated are with calibration period of 1 year Test Setup Aux equipment CDN EUT CDN Aux equipment Ground Reference Plane T Non-Conducted Table T Test Level RF-Generator PA Item Environmental Phenomena Units Test Specification Performance Criteria Ports for Signal Lines and Data Buses, not involved in process control, etc. MHz Radio-Frequency V (rms, Unmodulated) 3 Common Mode. % AM (1kHz) 80 A Amplitude Modulated Source Impedance Ω 150 AC Input and AC Output & DC Input and DC output Power Ports & Functional Earth Ports Radio-Frequency Common Mode. MHz V (rms, Unmodulated) A Page : 21 of 45

22 Amplitude Modulated % AM (1kHz) Source Impedance Ω Test Procedure The EUT are placed on a table that is 0.8 meter height, and a Ground reference plane on the table, EUT are placed upon table and use a 10cm insulation between the EUT and Ground reference plane. For Signal Ports and Telecommunication Ports The disturbance signal is through a coupling and decoupling networks (CDN) or EM-clamp device couples to the signal and Telecommunication lines of the EUT. For Input DC and AC Power Ports The EUT is connected to the power mains through a coupling and decoupling networks for power supply lines. And directly couples the disturbances signal into EUT. Used CDN-M2 for two wires or CDN-M3 for three wires. All the scanning conditions are as follows: Condition of Test Remarks 1. Field Strength 130dBuV(3V) Level 2 2. Radiated Signal AM 80% Modulated with 1kHz sinusoidal audio signal 3. Scanning Frequency 0.15MHz 80MHz 4 Dwell Time 2.86 Seconds 5. Frequency step size f : 150kHz to 5MHz shall be 50kHz. 5MHz~80MHz shall be 1% 6. The rate of Swept of Frequency 1.5 x 10-3 decades/s 8.5. Test Specification According to EN : Test Result The measurement of the Conducted Susceptibility was investigated and test result was shown in section 11. The acceptance criterion was met and the EUT passed the test. Page : 22 of 45

23 9. Voltage Dips and Interruption Measurement 9.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration 1 Voltage Dips Generator SCHAFFNER BEST Jun., 2001 S/N: SC 2 No.3 Shielded Room N/A Note: All equipment upon which need to calibrated are with calibration period of 1 year Test Setup To AC Line Voltage Dips/ Interruptions /Variations Simulator AC Power Line to EUT AL EUT Load Non-Conducted Table 80cm Controller Computer Printer 9.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria AC Input and AC Output Power Ports Voltage Dips Voltage Dips Voltage Interruptions % Reduction ms % Reduction ms % Reduction ms > 95 % 5000 B B C Page : 23 of 45

24 9.4. Test Procedure The EUT and its load are placed on a table which is 0.8 meter above a metal ground plane measured 1m*1m min. And 0.65mm thick min. And projected beyond the EUT by at least 0.1m on all sides. The power cord shall be used the shortest power cord as specified by the manufacturer. For Voltage Dips/ Interruptions test: The selection of test voltage is based on the rated power range. If the operation range is large than 20% of lower power range, both end of specified voltage shall be tested. Otherwise, the typical voltage specification is selected as test voltage. The EUT is connected to the power mains through a coupling device that directly couples to the Voltage Dips and Interruption Generator. The EUT shall be tested for 30% voltage dip of supplied voltage and duration 10ms, for 60% voltage dip of supplied voltage and duration 100ms with a sequence of three voltage dips with intervals of 10 seconds, and for 95% voltage interruption of supplied voltage and duration 5000ms with a sequence of three voltage interruptions with intervals of 10 seconds. Voltage phase shifting are shall occur at 0 0, 45 0, 90 0,135 0,180 0,225 0, 270 0,315 0 of the voltage Test Specification According to EN : Test Result The measurement of the Voltage Dips and Interruption was investigated and test result was shown in section 11. The acceptance criterion was met and the EUT passed the test. Page : 24 of 45

25 10. EMC Reduction Method During Compliance Testing No modification was made during testing. Page : 25 of 45

26 11. Test Result The test results in the emission and the immunity were performed according to the requirements of measurement standard and process. Quietek Corporation is assumed full responsibility for the accuracy and completeness of these measurements. The test data of the emission is listed as below. All the tests were carried out with the EUT in normal operation, which was defined as: Test Mode: EMI Mode Mode 1: Data Transmit Mode 2: Data Receive EMS Mode Mode 1: Data Transmit Mode 2: Data Receive Page : 26 of 45

27 11.1. Test Data of Conducted Emission Product : PC2PC-Bluetooth Test Item : Conducted Emission Test Test Site : No.4 Shielded Room Test Mode : Mode 1: Data Transmit Frequency Cable LISN Reading Emission Limits Loss Factor Level Level MHz db db dbuv dbuv dbuv ================================================================== Quasi-Peak Detector * Average Detector Remarks : 1. All Readings below 1GHz are Quasi-Peak value. 2. * means that this data is the worst emission level. 3. Emission Level = Reading Level + LISN Factor + Cable loss Page : 27 of 45

28 Product : PC2PC-Bluetooth Test Item : Conducted Emission Test Test Site : No.4 Shielded Room Test Mode : Mode 1: Data Transmit Frequency Cable LISN Reading Emission Limits Loss Factor Level Level MHz db db dbuv dbuv dbuv ================================================================== Quasi-Peak Detector * Average Detector Remarks : 1. All Readings below 1GHz are Quasi-Peak value. 2. * means that this data is the worst emission level. 3. Emission Level = Reading Level + LISN Factor + Cable loss. Page : 28 of 45

29 Product : PC2PC-Bluetooth Test Item : Conducted Emission Test Test Site : No.4 Shielded Room Test Mode : Mode 2: Data Receive Frequency Cable LISN Reading Emission Limits Loss Factor Level Level MHz db db dbuv dbuv dbuv ================================================================== Quasi-Peak Detector * Average Detector Remarks : 1. All Readings below 1GHz are Quasi-Peak value. 2. * means that this data is the worst emission level. 3. Emission Level = Reading Level + LISN Factor + Cable loss Page : 29 of 45

30 Product : PC2PC-Bluetooth Test Item : Conducted Emission Test Test Site : No.4 Shielded Room Test Mode : Mode 2: Data Receive Frequency Cable LISN Reading Emission Limits Loss Factor Level Level MHz db db dbuv dbuv dbuv ================================================================== Quasi-Peak Detector * Average Detector Remarks : 1. All Readings below 1GHz are Quasi-Peak value. 2. * means that this data is the worst emission level. 3. Emission Level = Reading Level + LISN Factor + Cable loss. Page : 30 of 45

31 11.2. Test Data of Radiated Emission Product : PC2PC-Bluetooth Test Item : Radiated Emission Test Site : No.2 OATS Test Mode : Mode 1: Data Transmit Frequency Cable Probe PreAMP Reading Emission Margin Limits Loss Factor Level Level MHz db db/m db dbuv dbuv/m db dbuv/m ================================================================== Horizontal * Vertical * Note: 1. All Readings below 1GHz are Quasi-Peak, above are average value. 2. *, means this data is the worst emission level. 3. Emission Level = Reading Level + Probe Factor + Cable loss. Page : 31 of 45

32 Product : PC2PC-Bluetooth Test Item : Radiated Emission Test Site : No.2 OATS Test Mode : Mode 2: Data Receive Frequency Cable Probe PreAMP Reading Emission Margin Limits Loss Factor Level Level MHz db db/m db dbuv dbuv/m db dbuv/m ================================================================== Horizontal * Vertical * Note: 1. All Readings below 1GHz are Quasi-Peak, above are average value. 2. *, means this data is the worst emission level. 3. Emission Level = Reading Level + Probe Factor + Cable loss. Page : 32 of 45

33 11.3. Test Data of Electrostatic Discharge Product : PC2PC-Bluetooth Test Item : Electrostatic Discharge Test Site : No.3 Shielded Room Test Mode : Mode 1: Data Transmit Item Air Discharge Amount of Discharge Voltage +8kV -8kV Required Criteria B B Complied To Criteria (A,B,C) A A Results Pass Pass Contact Discharge kV -4kV B B A A Pass Pass Indirect Discharge 10 +4kV B A Pass (HCP) 10-4kV B A Pass Indirect Discharge 10 +4kV B A Pass (VCP Front) 10-4kV B A Pass Indirect Discharge 10 +4kV B A Pass (VCP Left) 10-4kV B A Pass Indirect Discharge 10 +4kV B A Pass (VCP Back) 10-4kV B A Pass Indirect Discharge 10 +4kV B A Pass (VCP Right) 10-4kV B A Pass NR: No Requirement Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv. No false alarms or other malfunctions were observed during or after the test. Page : 33 of 45

34 Product : PC2PC-Bluetooth Test Item : Electrostatic Discharge Test Site : No.1 Shielded Room Test Mode : Mode 2: Data Receive Item Air Discharge Amount of Discharge Voltage +8kV -8kV Required Criteria B B Complied To Criteria (A,B,C) A A Results Pass Pass Contact Discharge kV -4kV B B A A Pass Pass Indirect Discharge 10 +4kV B A Pass (HCP) 10-4kV B A Pass Indirect Discharge 10 +4kV B A Pass (VCP Front) 10-4kV B A Pass Indirect Discharge 10 +4kV B A Pass (VCP Left) 10-4kV B A Pass Indirect Discharge 10 +4kV B A Pass (VCP Back) 10-4kV B A Pass Indirect Discharge 10 +4kV B A Pass (VCP Right) 10-4kV B A Pass NR: No Requirement Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv. No false alarms or other malfunctions were observed during or after the test. Page : 34 of 45

35 11.4. Test Data of Radiated Susceptibility Product : PC2PC-Bluetooth Test Item : Radiated Susceptibility Test Site : No.1 EMC fully Chamber Test Mode : Mode 1: Data Transmit Field Complied To Frequency Position Polarity Required Strength Criteria (MHz) (Angle) (H or V) Criteria (V/m) (A,B,C) Results H 3 A A Pass V 3 A A Pass H 3 A A Pass V 3 A A Pass H 3 A A Pass V 3 A A Pass H 3 A A Pass V 3 A A Pass Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information There was no observable degradation in performance. EUT stopped operation and could / could not be reset by operator at at frequency MHz. No false alarms or other malfunctions were observed during or after the test. V/m Page : 35 of 45

36 Product : PC2PC-Bluetooth Test Item : Radiated Susceptibility Test Site : No.1 EMC fully Chamber Test Mode : Mode 2: Data Receive Field Complied To Frequency Position Polarity Required Strength Criteria (MHz) (Angle) (H or V) Criteria (V/m) (A,B,C) Results H 3 A A Pass V 3 A A Pass H 3 A A Pass V 3 A A Pass H 3 A A Pass V 3 A A Pass H 3 A A Pass V 3 A A Pass Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information There was no observable degradation in performance. EUT stopped operation and could / could not be reset by operator at at frequency MHz. No false alarms or other malfunctions were observed during or after the test. V/m Page : 36 of 45

37 11.5. Test Data of Electrical Fast Transient Product : PC2PC-Bluetooth Test Item : Electrical Fast Transient Test Site : No.1 Shielded Room Test Mode : Mode 1: Data Transmit Inject Line Polarity Voltage kv Inject Time (Second) Inject Method Required Criteria Complied to Criteria Result L ± 1kV 60 Direct B A Pass N ± 1kV 60 Direct B A Pass PE ± 1kV 60 Direct B A Pass L+N ± 1kV 60 Direct B A Pass L+PE ± 1kV 60 Direct B A Pass N+PE ± 1kV 60 Direct B A Pass L+N+PE ± 1kV 60 Direct B A Pass Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at Line. No false alarms or other malfunctions were observed during or after the test. kv of Page : 37 of 45

38 Product : PC2PC-Bluetooth Test Item : Electrical Fast Transient Test Site : No.1 Shielded Room Test Mode : Mode 2: Data Receive Inject Line Polarity Voltage kv Inject Time (Second) Inject Method Required Criteria Complied to Criteria Result L ± 1kV 60 Direct B A Pass N ± 1kV 60 Direct B A Pass PE ± 1kV 60 Direct B A Pass L+N ± 1kV 60 Direct B A Pass L+PE ± 1kV 60 Direct B A Pass N+PE ± 1kV 60 Direct B A Pass L+N+PE ± 1kV 60 Direct B A Pass Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at Line. No false alarms or other malfunctions were observed during or after the test. kv of Page : 38 of 45

39 11.6. Test Data of Surge Product : PC2PC-Bluetooth Test Item : Surge Test Site : No.1 Shielded Room Test Mode : Mode 1: Data Transmit Inject Line Polarity Angle Voltage kv Time Interval (Second) Inject Method Required Criteria Complied to Criteria Result L-N ± 0 0.5kV 60 Direct B A Pass L-N ± kV 60 Direct B A Pass L-N ± kV 60 Direct B A Pass L-N ± kV 60 Direct B A Pass L-PE ± 0 1kV 60 Direct B A Pass L-PE ± 90 1kV 60 Direct B A Pass L-PE ± 180 1kV 60 Direct B A Pass L-PE ± 270 1kV 60 Direct B A Pass N-PE ± 0 1kV 60 Direct B A Pass N-PE ± 90 1kV 60 Direct B A Pass N-PE ± 180 1kV 60 Direct B A Pass N-PE ± 270 1kV 60 Direct B A Pass Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at Line. No false alarms or other malfunctions were observed during or after the test. kv of Page : 39 of 45

40 Product : PC2PC-Bluetooth Test Item : Surge Test Site : No.1 Shielded Room Test Mode : Mode 2: Data Receive Inject Line Polarity Angle Voltage kv Time Interval (Second) Inject Method Required Criteria Complied to Criteria Result L-N ± 0 0.5kV 60 Direct B A Pass L-N ± kV 60 Direct B A Pass L-N ± kV 60 Direct B A Pass L-N ± kV 60 Direct B A Pass L-PE ± 0 1kV 60 Direct B A Pass L-PE ± 90 1kV 60 Direct B A Pass L-PE ± 180 1kV 60 Direct B A Pass L-PE ± 270 1kV 60 Direct B A Pass N-PE ± 0 1kV 60 Direct B A Pass N-PE ± 90 1kV 60 Direct B A Pass N-PE ± 180 1kV 60 Direct B A Pass N-PE ± 270 1kV 60 Direct B A Pass Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at Line. No false alarms or other malfunctions were observed during or after the test. kv of Page : 40 of 45

41 11.7. Test Data of Conducted Susceptibility Product : PC2PC-Bluetooth Test Item : Conducted Susceptibility Test Site : No.3 Shielded Room Test Mode : Mode 1: Data Transmit Frequency Voltage Inject Tested Port Required Performance Result Range Applied Method of Criteria Criteria Complied (MHz) dbuv(v) EUT To 0.15~80 130(3V) CDN AC IN A A PASS Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. Page : 41 of 45

42 Product : PC2PC-Bluetooth Test Item : Conducted Susceptibility Test Site : No.3 Shielded Room Test Mode : Mode 2: Data Receive Frequency Voltage Inject Tested Port Required Performance Result Range Applied Method of Criteria Criteria Complied (MHz) dbuv(v) EUT To 0.15~80 130(3V) CDN AC IN A A PASS Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. Page : 42 of 45

43 11.8. Test Data of Voltage Dips and Interruption Product : PC2PC-Bluetooth Test Item : Voltage Dips and Interruption Test Site : No.1 Shielded Room Test Mode : Mode 1: Data Transmit Voltage Dips and Interruption Reduction(%) Angle Test Duration (ms) Required Performance Criteria Performance Criteria Complied To Test Result B A PASS B A PASS B A PASS B A PASS B A PASS B A PASS B A PASS B A PASS B B PASS B B PASS B B PASS B B PASS B B PASS B B PASS B B PASS B B PASS > C C PASS > C C PASS > C C PASS > C C PASS > C C PASS > C C PASS > C C PASS > C C PASS Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information The nominal voltage of EUT is 230V. EUT stopped operation and could / could not be reset by operator at kv of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. Page : 43 of 45

44 Product : PC2PC-Bluetooth Test Item : Voltage Dips and Interruption Test Site : No.1 Shielded Room Test Mode : Mode 2: Data Receive Voltage Dips and Interruption Reduction(%) Angle Test Duration (ms) Required Performance Criteria Performance Criteria Complied To Test Result B A PASS B A PASS B A PASS B A PASS B A PASS B A PASS B A PASS B A PASS B B PASS B B PASS B B PASS B B PASS B B PASS B B PASS B B PASS B B PASS > C C PASS > C C PASS > C C PASS > C C PASS > C C PASS > C C PASS > C C PASS > C C PASS Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information The nominal voltage of EUT is 230V. EUT stopped operation and could / could not be reset by operator at kv of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. Page : 44 of 45

45 Attachment 1: EUT Test Photographs Page : 45 of 45

46 Report No.: 024L064E Attachment 1 : EUT Test Photographs Front View of Conducted Test Back View of Conducted Test Page : 1 of 5

47 Report No.: 024L064E Front View of Radiated Test Back View of Radiated Test Page : 2 of 5

48 Report No.: 024L064E ESD Test Setup RS Test Setup Page : 3 of 5

49 Report No.: 024L064E EFT/B Test Setup Surge Test Setup Page : 4 of 5

50 Report No.: 024L064E CS Test Setup Dips Test Setup Page : 5 of 5

51 Attachment 2: EUT Detailed Photographs Page : 46 of 45

52 Report No.: 024L064E Attachment 2 : EUT Detailed Photographs (1) EUT Photo (2) EUT Photo Page : 1 of 3 Version : 1.0

53 Report No.: 024L064E (3) EUT Photo (4) EUT Photo Page : 2 of 3 Version : 1.0

54 Report No.: 024L064E (5) EUT Photo Page : 3 of 3 Version : 1.0

55 Reference : Laboratory of License Page : 47 of 45

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72