Report No: R-RFCEP14V02. Test Report. For:Intel

Transcription

1 Test Report For:Intel Product Name Notebook Model No. MS-163KXXX (X=0~9 or A~Z Blank) Transmitter Module Intel / 512 AN_HMW Antenna Kit VSO: S V03 (Right) S V03 (Left ) Applicant Address MICRO-STAR INT L Co., LTD. No. 69, Li-De St., Jung-He City, Taipei Hsien, Taiwan, R.O.C. Date of Receipt Apr. 10, 2008 Date of Test May 09, 2008 Report No R-RFCEP14V02 Version V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Page: 1 of 55

2 Test Report Certification Date of Test: May 09, 2008 Report No.: R-RFCEP14V02 Accredited by TUV, DNV, Nemko and NIST (NVLAP) Product Name Applicant Address Manufacturer Model No. Transmitter Module Antenna Kit Notebook MICRO-STAR INT L Co., LTD. No. 69, Li-De St., Jung-He City, Taipei Hsien, Taiwan, R.O.C. MICRO-STAR INT L Co., LTD. MS-163KXXX (X=0~9 or A~Z Blank) Intel / 512 AN_HMW VSO: S V03 (Right) S V03 (Left ) Rated Voltage Working Voltage Trade Name AC 230V/50Hz DC 3.3V (via Mini-PCI slot) MSI Measurement Standard ETSI EN :V1.7.1 ( ) 4.3.1& ETSI EN V1.4.1 ( ) 4.3.1& Test Result Complied The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Documented By : (Senior Engineering Adm. Specialist / Anita Chou) Tested By : ( Assistant Engineer / Dino Chen ) Approved By : ( Deputy Manager / Vincent Lin ) Page: 2 of 55

3 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION EUT Description CRTU-ABG Software Parameter Test Channel and Data Rate Tested System Details Configuration of Tested System EUT Exercise Software Test Facility Equivalent Isotropic Radiated Power Test Equipment Test Setup Test Condition Limits Test Procedure Test Specification Uncertainty Test Result Test Data of Equivalent Isotropic Radiated Power Antenna Assembly Summary Spurious Emission Test Equipment Test Setup Test Condition Limits Test Procedure Test Specification Uncertainty Test Result Test Data of Spurious Emission Measurement Uncertainty Values EMC Reduction Method During Compliance Testing Attachment 1: EUT Test Photographs...43 Attachment 2 : EUT Detailed Photographs Page: 3 of 55

4 Report No R-RFCEP14V02 1. GENERAL INFORMATION 1.1. EUT Description Product Name Trade Name Model No. Transmitter Module MAC Number Frequency Range Notebook MSI MS-163KXXX (X=0~9 or A~Z Blank) Intel / 512 AN_HMW 0016EA04372E MHz, MHz and MHz Number of Channels b/g/n-20MHz/n-40MHz: 13, a/n-20MHz: n-40MHz: 9 Maximum Data Rate b: 11Mbps, a/g: 54Mbps, n: 300Mbps Channel Separation b/g/n-20MHz: 5 MHz, a/n-20MHz: 20MHz n-40MHz: 40MHz Antenna Kit VSO: S V03 (Right) S V03 (Left ) Antenna Gain Refer to the table Antenna List Antenna Type PCB(Dipole) Type of Modulation DSSS/OFDM Channel Control Auto Power Adapter MFR: LI SHIN, M/N: 0335A1965 Input: AC V, 50-60Hz 1.7A Output: DC 19V, 3.42A Cable out: Shielded, 1.8m with one ferrite core bonded. Antenna List No. Manufacturer Part No. Peak Gain 1 VSO S V03 (Right) S V03 (Left) 0.75dBi for 2.4GHz -0.22dBi for 5GHz Page: 4 of 55

5 Report No R-RFCEP14V CRTU-ABG Software Parameter Parameter Test Mode Data Rate (Mbps) Antenna Channel Frequency Value MCS0 A n (20MHz) MCS0 A MCS0 A MCS0 A A A A A A Quickly measure the Duty Cycle again of the signal. When using CRTU Version , this will depend on the version and the bit rate. The duty cycle x delivers a correction factor to determine EIRP Test Channel and Data Rate It is necessary to measure e.i.r.p on following frequencies: n-20MHz 2.4GHz band: 2412MHz, 2442MHz, 2472MHz. 5GHz band : 5180MHz, 5260MHz, 5320MHz, 5500MHz, 5600MHz, 5700MHz Tests are performed at following date rates: n-20Mbps MCS0 in 2412MHz, 2442MHz, 2472MHz. MCS0 in 5180MHz, 5260MHz, 5320MHz, 5500MHz, 5600MHz, 5700MHz Note: 1. QuieTek verified all construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: EMI Test Mode Mode 1: Transmit, n(20MHz)-2.4GHz band Mode 2: Transmit, n(20MHz)-5GHz band Mode 3: Receiver, n(20MHz)-2.4GHz band Mode 4: Receiver, n(20MHz)-2.4GHz band Page: 5 of 55

6 Report No R-RFCEP14V Tested System Details The types for all equipment, plus descriptions of all cables used in the tested system (including inserted cards) are: Product Manufacturer Model No. Serial No. FCC ID Power Cord (1) N/A N/A N/A N/A N/A N/A Signal Cable Type A. N/A N/A Signal cable Description 1.5. Configuration of Tested System EUT 1.6. EUT Exercise Software (1) Setup the EUT as shown in Section 1.5. (2) Execute the continuous transmission software of Intel CRTU v (3) Setup the test mode, the test channel and the data rate. (4) Press OK to start the continuous transmission. (5) Verify that the EUT works correctly. Page: 6 of 55

7 Report No R-RFCEP14V Test Facility Ambient conditions in the laboratory: Items Test Item Required (IEC 68-1) Actual Temperature ( C) ETSI EN Humidity (%RH) ETSI EN Site Description: File on Federal Communications Commission FCC Engineering Laboratory 7435 Oakland Mills Road Columbia, MD Registration Number: Accreditation on NVLAP NVLAP Lab Code: Site Name: Site Address: Quietek Corporation No. 5-22, Ruei-Shu Valley, Ruei-Ping Tsuen, Lin-Kou Shiang, Taipei, Taiwan, R.O.C. TEL: / FAX: service@quietek.com Page: 7 of 55

8 Report No R-RFCEP14V02 2. Equivalent Isotropic Radiated Power 2.1. Test Equipment The following test equipments are used during the effective radiated power measurement: Equipment Manufacture Model No Serial No. Last Cal. Power Meter Anritsu ML2495A 6K May, 2008 Power Sensor Anritsu MA2491A May, 2008 Note: All equipments upon which need to be calibrated are with calibration period of 1 year Test Setup Conducted Power Measurement EUT RF Cable SMA Connecter Power Meter 2.3. Test Condition The normal temperature and humidity conditions for tests shall be any convenient combination of temperature and humidity within the following ranges: - Temperature: +15 C to +35 C; - Relative humidity: 20 % to 75 % Limits n-20MHz:(EN V1.7.1 Clause ) The effective radiated power is defined as the total power of the transmitter and is calculated according to the test procedure. The effective radiated power shall be equal to or less than -10 dbw (100 mw) e.i.r.p n-20MHz:(EN V1.4.1 Clause ) Page: 8 of 55

9 Report No R-RFCEP14V02 Mean EIRP limits ofr RF output power at the Highest power level Frequency range [MHz] Mean EIRP [dbm] 5150 to to Test Procedure The measurement is performed using normal operation of the equipment with test modulation applied. The test procedure is as follows: step 1: - Using a suitable means, the output of the transmitter shall be coupled to a matched diode detector; - The output of the diode detector shall be connected to the vertical channel of an oscilloscope. - The combination of the diode detector and the oscilloscope shall be capable of faithfully reproducing the envelope peaks and the duty cycle of the transmitter output signal. - The observed duty cycle of the transmitter (Tx on/(tx on +Tx off)) shall be noted as x, (0 < x < 1) and recorded. For the purpose of testing, the equipment shall be operated with a duty cycle that is equal to or more than 0,1. step 2: - The average output power of the transmitter shall be determined using a wideband, calibrated RF power meter with a matched thermocouple detector or an equivalent thereof and, where applicable, with an integration period that exceeds the repetition period of the transmitter by a factor 5 or more. The observed value shall be recorded as "A" (in dbm). - The e.i.r.p. shall be calculated from the above measured power output A, the observed duty cycle x, and the applicable antenna assembly gain "G" in dbi, according to the formula: P = A + G + 10 log (1/x); P shall be recorded in the test report. (Not exceed the value specified in ETSI EN V1.7.1 clause and ETSI EN V1.4.1 clause ) 2.6. Test Specification According to ETSI EN V1.7.1 ( ) clause According to ETSI EN V1.4.1 ( ) clause Uncertainty ± 1.27dB Page: 9 of 55

10 Report No R-RFCEP14V Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 2.9. The acceptance criterion was met and the EUT passed the test. Page: 10 of 55

11 Report No R-RFCEP14V Test Data of Equivalent Isotropic Radiated Power Product Test Item Test Mode : Notebook : Equivalent Isotropic Radiated Power : Mode 1: Transmit, n(20MHz)-2.4GHz band Effective Test Conditions Freq. Measured output power A (dbm) Antenna Gain (dbi) 10log(1/x) radiated power P (dbm) Limit (dbm) e.i.r.p Tnom 25 o C Vnom 230V Note: P is the effective radiated power as defined in clause step 2,P=A+G+10log(1/x) Test Result PASS Page: 11 of 55

12 Report No R-RFCEP14V02 Product Test Item Test Mode : Notebook : Transmit Power Control : Mode 2: Transmit, n(20MHz)-5GHz band Test Conditions Freq. Measured output power A (dbm) Antenna Gain (dbi) 10log(1/x) Effective radiated power P (dbm) e.i.r.p Limit (dbm) Tnom 25 o C Vnom 230V Note: P is the effective radiated power as defined in clause step 2, P=A+G+10 log(1/x) Test Result PASS Page: 12 of 55

13 Report No R-RFCEP14V02 3. Antenna Assembly Summary Peak Gain W/ Cable loss Antenna Part Number Manufacture Antenna Type Frequency Max Gain (dbi) S V03 (Right) VSO PCB(Dipole) S V03 (Left) VSO PCB(Dipole) Page: 13 of 55

14 Report No R-RFCEP14V02 4. Transmitter Spurious Emission 4.1. Test Equipment The following test equipment are used during the radiated spurious emission test: Test Site Equipment Manufacturer Model No./Serial No. Last Cal. Site # 3 Spectrum Analyzer HP E4407B / US May, 2008 Bilog Antenna SCHAFFNER CBL6112B / 2697 May, 2008 Horn Antenna Schwarzbeck BBHA9120D/497 July, 2007 Horn Antenna Schwarzbeck BBHA9170/208 July, 2007 Pre-Amplifier QTK QTK-AMP-01 / 0001 July, 2007 Pre-Amplifier MITEQ AMF-4D P/ May, 2008 Notch Filter Assembly Microwave Circuits N / N Nov, 2007 Notch Filter Assembly Microwave Circuits N / N Nov, 2007 Highpass Filter Assembly Microwave Circuits H5502G21/ H5502G21 Nov, 2007 Note: 1. All equipments that need to be calibrated are with calibration period of 1 year. 2. Mark X test instruments are used to measure the final test results. Page: 14 of 55

15 Report No R-RFCEP14V Test Setup Under 1GHz Test Setup 3m FRP Dome EUT 15m Antenna Mast Bilog Antenna Antenna height can be moved from 1m to 4m, Antenna and turntable distance 3m Fully soldered Metal Ground Receiver Above 1GHz Test Setup 3m FRP Dome EUT 1.5m Antenna Mast Horn Antenna Antenna height can be moved from 1m to 4m, Antenna and turntable distance 3m Fully soldered Metal Ground Spectrum Amplifier Above 18 GHz Test Setup 3m FRP Dome EUT 15m Antenna Mast Horn Antenna Antenna height can be moved from 1m to 4m, Antenna and turntable distance 1m Spectrum Amplifier Page: 15 of 55

16 Report No R-RFCEP14V Test Condition The normal temperature and humidity conditions for tests shall be any convenient combination of temperature and humidity within the following ranges: - Temperature: +15 C to +35 C; - Relative humidity: 20 % to 75 % Limits n-20MHz 2.4GHz band: Transmitter limits for narrowband spurious emission (EN V1.7.1 Clause ) Frequency Range Limit when operating Measurement Bandwidth 30MHz to 1 GHz -36 dbm 100 khz Above 1 GHz to GHz -30 dbm 100 khz 1.8 GHz to 1.9 GHz 5.15 GHz to 5.3 GHz -47 dbm 100 khz Receiver limits for narrowband spurious emission (EN V1.7.1 Clause ) Frequency Range Limit Measurement Bandwidth 30MHz to 1 GHz -57 dbm 100 khz Above 1 GHz to GHz -47 dbm 100 khz Page: 16 of 55

17 Report No R-RFCEP14V n-20MHz 5GHz band: Transmitter limits for narrowband spurious emission (EN V1.4.1 Clause ) Transmitter unwanted emission limits outside the 5 GHz RLAN bands Frequency range Maximum Power, ERP [dbm] Measurement Bandwidth 25 MHz to 47 MHz khz 47MHz to 74 MHz khz 74 MHz to 87.5 MHz khz 87.5 MHz to 118 MHz khz 118 MHz to 174 MHz khz 174 MHz to 230 MHz khz 230 MHz to 470 MHz khz 470 MHz to 862 MHz khz 862 MHz to 1 GHz khz 1 GHz to 5.15 GHz MHz 5.35 GHz to 5.47 GHz MHz GHz to 26.5 GHz MHz Receiver limits for spurious emission (EN V1.4.1 Clause 4.6.2) Receiver limits for spurious emission Frequency range Maximum Power, ERP [dbm] Measurement Bandwidth 30MHz to 1 GHz -57 dbm 100 khz Above 1 GHz to GHz -47 dbm 1MHz Page: 17 of 55

18 Report No R-RFCEP14V Test Procedure The EUT and its simulators are placed on a turn table which is 1.5 meters above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meters.the antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Broadband antenna (calibrated bi-log and horn antenna) are used as a receiving antenna. Both horizontal and vertical polarization of the antenna are set on measurement. And a high frequency preamlifier were used increase the sensitivity of the measuring. In order to find the maximum emission, all of the interface cables must be manipulated according to ETSI EN :V1.7.1 ( ) & ETSI EN V1.4.1 ( ) on radiated measurement. The additional notch filter below 1GHz was used to measure the level of harmonics radiated emission during field strength of harmonics measurement. The bandwidth below 1GHz setting on the field strength meter is 120 khz, and 100 khz bandwidth is adopted above 1GHz. The frequency range from 30MHz to 12.75GHz is checked a frequency range from 25MHz to 26.5GHz is checked and bandwidth reference 3.4 limit 4.6. Test Specification According to ETSI EN :V1.7.1 ( ) clause According to ETSI EN V1.4.1 ( ) clause Uncertainty ± 3.9 db above 1GHz ± 3.8 db below 1GHz 4.8. Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 3.9. The acceptance criterion was met and the EUT passed the test. Page: 18 of 55

19 Report No R-RFCEP14V Test Data of Spurious Emission Product : Notebook Test Item : Transmitter spurious emission Test Site : No.3 Chamber Test Mode : Mode 1: Transmit, n(20MHz)-2.4GHz band Chennal / Frequency TX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH01 / 2412MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 19 of 55

20 Report No R-RFCEP14V02 Product : Notebook Test Item : Transmitter spurious emission Test Site : No.3 Chamber Test Mode : Mode 1: Transmit, n(20MHz)-2.4GHz band Chennal / Frequency TX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH07 / 2442MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 20 of 55

21 Report No R-RFCEP14V02 Product : Notebook Test Item : Transmitter spurious emission Test Site : No.3 Chamber Test Mode : Mode 1: Transmit, n(20MHz)-2.4GHz band Chennal / Frequency TX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH13 / 2472MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 21 of 55

22 Report No R-RFCEP14V02 Product : Notebook Test Item : Transmitter spurious emission Test Site : No.3 Chamber Test Mode : Mode 2: Transmit, n(20MHz)-5GHz band Chennal / Frequency CH36 / 5180MHz TX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 22 of 55

23 Report No R-RFCEP14V02 Product : Notebook Test Item : Transmitter spurious emission Test Site : No.3 Chamber Test Mode : Mode 2: Transmit, n(20MHz)-5GHz band Chennal / Frequency TX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH52 / 5260MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 23 of 55

24 Report No R-RFCEP14V02 Product : Notebook Test Item : Transmitter spurious emission Test Site : No.3 Chamber Test Mode : Mode 2: Transmit, n(20MHz)-5GHz band Chennal / Frequency TX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH64 / 5320MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 24 of 55

25 Report No R-RFCEP14V02 Product : Notebook Test Item : Transmitter spurious emission Test Site : No.3 Chamber Test Mode : Mode 2: Transmit, n(20MHz)-5GHz band Chennal / Frequency TX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH100 / 5500MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 25 of 55

26 Report No R-RFCEP14V02 Product : Notebook Test Item : Transmitter spurious emission Test Site : No.3 Chamber Test Mode : Mode 2: Transmit, n(20MHz)-5GHz band Chennal / Frequency TX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH120 / 5600MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 26 of 55

27 Report No R-RFCEP14V02 Product : Notebook Test Item : Transmitter spurious emission Test Site : No.3 Chamber Test Mode : Mode 2: Transmit, n(20MHz)-5GHz band Chennal / Frequency TX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH140 / 5700MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 27 of 55

28 Report No R-RFCEP14V02 5. Receiver Spurious Emission 5.1. Test Equipment The following test equipment are used during the radiated spurious emission test: Test Site Equipment Manufacturer Model No./Serial No. Last Cal. Site # 3 Spectrum Analyzer HP E4407B / US May, 2008 Bilog Antenna SCHAFFNER CBL6112B / 2697 May, 2008 Horn Antenna Schwarzbeck BBHA9120D/497 July, 2007 Horn Antenna Schwarzbeck BBHA9170/208 July, 2007 Pre-Amplifier QTK QTK-AMP-01 / 0001 July, 2007 Pre-Amplifier MITEQ AMF-4D P/ May, 2008 Notch Filter Assembly Microwave Circuits N / N Nov, 2007 Notch Filter Assembly Microwave Circuits N / N Nov, 2007 Highpass Filter Assembly Microwave Circuits H5502G21/ H5502G21 Nov, 2007 Note: 1. All equipments that need to be calibrated are with calibration period of 1 year. 2. Mark X test instruments are used to measure the final test results. Page: 28 of 55

29 Report No R-RFCEP14V Test Setup Under 1GHz Test Setup 3m FRP Dome EUT 15m Antenna Mast Bilog Antenna Antenna height can be moved from 1m to 4m, Antenna and turntable distance 3m Fully soldered Metal Ground Receiver Above 1GHz Test Setup 3m FRP Dome EUT 1.5m Antenna Mast Horn Antenna Antenna height can be moved from 1m to 4m, Antenna and turntable distance 3m Fully soldered Metal Ground Spectrum Amplifier Above 18 GHz Test Setup 3m FRP Dome EUT 15m Antenna Mast Horn Antenna Antenna height can be moved from 1m to 4m, Antenna and turntable distance 1m Spectrum Amplifier Page: 29 of 55

30 5.3. Test Condition The normal temperature and humidity conditions for tests shall be any convenient combination of temperature and humidity within the following ranges: - Temperature: +15 C to +35 C; - Relative humidity: 20 % to 75 % Limits n-20MHz 2.4GHz band: Receiver limits for narrowband spurious emission (EN V1.7.1 Clause ) Frequency Range Limit Measurement Bandwidth 30MHz to 1 GHz -57 dbm 100 khz Above 1 GHz to GHz -47 dbm 100 khz n-20MHz 5GHz band: Receiver limits for spurious emission (EN V1.4.1 Clause 4.6.2) Receiver limits for spurious emission Frequency range Maximum Power, ERP [dbm] Measurement Bandwidth 30MHz to 1 GHz -57 dbm 100 khz Above 1 GHz to GHz -47 dbm 1MHz 5.5. Test Procedure The EUT and its simulators are placed on a turn table which is 1.5 meters above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meters.the antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Broadband antenna (calibrated bi-log and horn antenna) are used as a receiving antenna. Both horizontal and vertical polarization of the antenna are set on measurement. And a high frequency preamlifier were used increase the sensitivity of the measuring. In order to find the maximum emission, all of the interface cables must be manipulated according to ETSI EN :V1.7.1 ( ) & ETSI EN V1.4.1 ( ) on radiated measurement. The additional notch filter below 1GHz was used to measure the level of harmonics radiated emission during field strength of harmonics measurement. The bandwidth below 1GHz setting on the field strength meter is 100 khz, and 100 khz bandwidth is adopted above 1GHz. The frequency range from 30MHz to 12.75GHz is checked. Page: 30 of 55

31 802.11a frequency range from 30MHz to 26.5GHz is checked and bandwidth reference 3.4 limit 5.6. Test Specification According to ETSI EN :V1.7.1 ( ) clause According to ETSI EN V1.4.1 ( ) clause Uncertainty ± 3.9 db above 1GHz ± 3.8 db below 1GHz 5.8. Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 3.9. The acceptance criterion was met and the EUT passed the test. Page: 31 of 55

32 5.9. Test Data of Spurious Emission Product : Notebook Test Item : Receiver spurious emissions Test Site : No.3 Chamber Test Mode : Mode 3: Receiver, n(20MHz)-2.4GHz band Chennal / Frequency RX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH01 / 2412MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 32 of 55

33 Product : Notebook Test Item : Receiver spurious emissions Test Site : No.3 Chamber Test Mode : Mode 3: Receiver, n(20MHz)-2.4GHz band Chennal / Frequency RX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH07 / 2442MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 33 of 55

34 Product : Notebook Test Item : Receiver spurious emissions Test Site : No.3 Chamber Test Mode : Mode 3: Receiver, n(20MHz)-2.4GHz band Chennal / Frequency RX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH13 / 2472MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 34 of 55

35 Product : Notebook Test Item : Receiver spurious emissions Test Site : No.3 Chamber Test Mode : Mode 2: Transmit, n(20MHz)-5GHz band Chennal / Frequency RX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH36 / 5180MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 35 of 55

36 Product : Notebook Test Item : Receiver spurious emissions Test Site : No.3 Chamber Test Mode : Mode 2: Transmit, n(20MHz)-5GHz band Chennal / Frequency RX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH52 / 5260MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 36 of 55

37 Product : Notebook Test Item : Receiver spurious emissions Test Site : No.3 Chamber Test Mode : Mode 2: Transmit, n(20MHz)-5GHz band Chennal / Frequency RX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH64 / 5320MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 37 of 55

38 Product : Notebook Test Item : Receiver spurious emissions Test Site : No.3 Chamber Test Mode : Mode 2: Transmit, n(20MHz)-5GHz band Chennal / Frequency RX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH100 / 5500MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 38 of 55

39 Product : Notebook Test Item : Receiver spurious emissions Test Site : No.3 Chamber Test Mode : Mode 2: Transmit, n(20MHz)-5GHz band Chennal / Frequency RX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH120 / 5600MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 39 of 55

40 Product : Notebook Test Item : Receiver spurious emissions Test Site : No.3 Chamber Test Mode : Mode 2: Transmit, n(20MHz)-5GHz band Chennal / Frequency RX Spurious Emission Measurement Frequency Measurement level(dbm) Horizontal Under 1G CH140 / 5700MHz Measurement Frequency Measurement level(dbm) Vertical Under 1G Page: 40 of 55

41 6. Measurement Uncertainty Values The maximum values of the absolute measurement uncertainties of the measurements defined in the present document shall not exceed the values given below: n-20MHz-2.4G band: Parameter Uncertainty Total RF power, conducted 1.5 db All emissions, radiated 6 db Temperature 1 o C Humidity 5 % DC and low frequency voltages 3 % For the measurement methods according to the present document these uncertainty figures are valid to a confidence level of 95 % calculated according to the methods described in ETR 028 [5], on guidelines for estimating uncertainties in measuring methods n-20MHz-5GHz band: Parameter RF power conducted Spurious emissions, radiated Uncertainty 0.75 db 6 db For the measurement methods according to the present document, the measurement uncertainty figures shall be calculated in accordance with ETR 028 [4] and shall correspond to an expansion factor (coverage factor) k = 1.96 or k = 2 (which provide confidence level of respectively 95 % and % in the case where the distributions characterizing the actual measurement uncertainties are normal (Gaussian)). Page: 41 of 55

42 7. EMC Reduction Method During Compliance Testing No modification was made during testing. Page: 42 of 55

43 Attachment 1: EUT Test Photographs Front View of Spurious Emission Test Front View of Spurious Emission Test (Horn) Page: 43 of 55

44 Front View of Spurious Emission Test (Horn) Page: 44 of 55

45 Attachment 2 : EUT Detailed Photographs (1) EUT Photo (2) EUT Photo Page: 45 of 55

46 (3) EUT Photo (4) EUT Photo Page: 46 of 55

47 (5) EUT Photo (6) EUT Photo Page: 47 of 55

48 (7) EUT Photo (8) EUT Photo Page: 48 of 55

49 (9) EUT Photo (10) EUT Photo Page: 49 of 55

50 (11) EUT Photo (12) EUT Photo Page: 50 of 55

51 (13) EUT Photo (14) EUT Photo Page: 51 of 55

52 (15) EUT Photo (16) EUT Photo Page: 52 of 55

53 (17) EUT Photo (18) EUT Photo Page: 53 of 55

54 (19) EUT Photo (20) EUT Photo Page: 54 of 55

55 (21) EUT Photo Page: 55 of 55