3M Scotchkote System Application Guide. High Performance Coating System for Degraded Plastisol Cladding Surfaces.
|
|
- Caren Wilson
- 5 years ago
- Views:
Transcription
1 High Performance Coating System for Degraded Plastisol Cladding Surfaces. - Issue 2 Surface Preparation & Cleaning Primer Stage Finish Coat(s) As required 3M Scotchkote Epoxy Primer MC 50µ Theoretical coverage rate at 50µ is 10 m²/litre 3M Scotchkote Urethane Coating PU 75µ Theoretical coverage rate at 75µ is 8m²/litre 1
2 Surface Preparation & Cleaning The degraded, flaking Plastisol should be stripped to bare metal. All surfaces should be high-pressure detergent washed to remove all dirt, debris, oil, diesel and other contamination. Any white zinc salts should be removed by light abrasion or rubbing with 3M Scotchbrite abrasive pads. Exposed steel surfaces should have areas of corrosion thoroughly wire brushed or ground with an angle grinder to give a minimum ST3 standard in accordance with BS7079 Part C. The use of a proprietary Mordant Solution/T Wash is recommended on Zinc surfaces. When used as directed by the manufacturer s instructions, this will provide a useful indicator of surface cleanliness as well as etching the surface. When used correctly the surface should turn blue/black. If this doesn t occur then the surface should be cleaned again and the Mordant Solution reapplied. Edges, joints, boltheads, etc. should then receive a stripe coat of 3M Scotchkote Epoxy Primer MC 135. This stripe coat should extend approximately 25mm either side of the repair. Scotchkote Epoxy Primer MC 135 should not be applied when the relative humidity exceeds 90% or when the surface to be coated is less than 3 C above the dew point. For optimum results a minimum material and substrate temperature of 7 C is necessary. 2
3 Priming of Previously Stripe Coated Areas and Remaining Zinc Surfaces With 3M Scotchkote Epoxy Primer MC 135 The previously applied stripe coat of Scotchkote Epoxy Primer MC 135 should be allowed to become at least touch dry before applying the overall coat of Scotchkote Epoxy Primer MC 135. Surfaces to be coated should be dry and free from contamination. Scotchkote Epoxy Primer MC 135 is a two component high performance epoxy coating, supplied as a Part A (Base) component and a Part B (Activator) component. The Part A (Base) component should be thoroughly stirred until a uniform colour is produced. The Part B (Activator) should then be added to the Part A (Base) component and then again thoroughly stirred for at least two minutes, to produce a homogeneous mixture. NOTE: If only part quantities of the Part A (Base) and Part B (Activator) are to be used, care must be taken to maintain the volume mixing ratio of 3:1 respectively as well as total compliance with the above mixing procedures. Scotchkote Epoxy Primer MC 135 should not be applied when the temperature of the substrate is less than 7 C and or when the surface to be coated is less than 3 C above the dew point. Scotchkote Epoxy Primer MC 135 should be applied by brush, roller or spray at a wet film thickness of 100 microns, which equates to a dry film thickness of 50 microns on a smooth surface. The theoretical coverage at 50 microns is 10m²/litre. Scotchkote Epoxy Primer MC 135 can be overcoated after a minimum of 16 hours at 20 C and provided surfaces are clean, the maximum overcoating time is three months. The following times are given as a guide for minimum overcoating at different temperatures. TEMPERATURE MINIMUM 10 C 32 hours 15 C 24 hours 20 C 16 hours 25 C 12 hours 30 C 8 hours 3
4 Application of 3M Scotchkote Urethane Coating PU 846 All prepared and patch coated/primed surfaces must be clean, dry and free from any contamination. Scotchkote Urethane Coating PU 846 is a single component finish and should only require stirring prior to use to incorporate any slight separation. Application of Scotchkote Urethane Coating PU 846 should not be carried out during rain, snow or when the surface is damp or covered with ice or when precipitation is likely to occur before the product has reached the touch dry stage. A stripe coat of Scotchkote Urethane Coating PU 846 should be first applied by brush to all joints and edges of sheets and allowed to become touch dry. This stripe coat should extend approximately 25mm either side of the repair. Scotchkote Urethane Coating PU 846 should now be applied by brush or roller at a wet film thickness of 125 microns, which equates to a dry film thickness of 75 microns on a smooth surface. The theoretical coverage at 75 microns is 8m²/litre. If the entire application is to be carried out by roller, a minimum of two coats of Scotchkote Urethane Coating PU 846 may be required to achieve the required film thickness. The applied system will be resistant to falling rain after approximately 4 hours. If rainfall is likely, the coated surface should be protected until it is touch dry. Scotchkote Urethane Coating PU 846 achieves full cure after 7 days at 20 C. Scotchkote Urethane Coating PU 846 can be overcoated after a minimum of 16 hours at 20 C. The following times are given as a guide for minimum overcoating at different temperatures. TEMPERATURE MINIMUM 10 C 32 hours 15 C 24 hours 20 C 16 hours 25 C 12 hours 30 C 8 hours 4
5 Touch Up and Repair Procedures Damage Back To Bare Substrate The damaged area and the immediately surrounding area should be cleaned and degreased. Any loose, flaking coating should be removed back to a sound edge, the exposed bare substrate and the immediately surrounding area of sound and firmly adhering coating should be abraded with either 120 or 240 grade abrasive paper using mechanical or manual methods depending on the extent and degree of damage taking care not to excessively damage the existing galvanised coating. After the abrading operation, any residual debris and dust must then be removed using airline or vacuum brush. The abraded areas should then be further degreased. Prepared surfaces should now be coated with T Wash followed with the Scotchkote system in accordance with the recommendations. NOTE: For very small areas, 3M Scotchkote Epoxy Primer MC 135 can be applied by brush but for larger areas or where optimum cosmetic appearance is required, spray application should be used. Damage Back To Scotchkote Epoxy Primer MC 135 The damaged area and the immediately surrounding area should be cleaned and degreased. Any loose, flaking coating should be removed back to a sound edge, the exposed primer should be lightly abraded and edges feathered in. After the abrading operation, any residual debris and dust must then be removed using airline or vacuum brush. The prepared areas should then be further degreased. Surfaces should now be coated with 3M Scotchkote Urethane Coating PU 846 in accordance with the recommendation. NOTE: For very small areas, Urethane Coating PU 846 can be applied by brush but for larger areas or where optimum cosmetic appearance is required, spray application should be used. 5
6 Notes Document References 3M Scotchkote Epoxy Primer MC 135 3M Scotchkote Urethane Coating PU 846 Product Technical Data Sheet 3M and Scotchkote are trademarks of 3M Company. Important Notice All statements, technical information and recommendations are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using the 3M Scotchkote Product, you must evaluate it and determine if it is suitable for your intended application. Because conditions of product use are outside of 3M control s and vary widely you assume all risks and liability associated with such use. Any product related statements not contained in current 3M publications, or any contrary statements contained in your purchase order, shall have no force or effect unless expressly agreed to in writing by an authorised officer of 3M. Warranty; Limited Remedy; Limited Liability. 3M warrants that the 3M Scotchkote Product will conform to 3M published specifications upon shipment. If the product is proven not to have met the specifications your exclusive remedy within 12 months of sale by 3M of the product and 3M's sole obligation will be, at 3M's option, to replace the Product or to refund the purchase price of the Product. Except where prohibited by law, this warranty is made in lieu of all other warranties, express or implied, including, but not limited to, any implied warranty of suitability or fitness for a particular purpose, or those arising from a course of dealing, custom or usage or trade. 3M has no obligation under this warranty with respect to any product that has failed due to inadequate or improper storage, handling, surface preparation, application, or maintenance; failure to follow product instructions or recommendations or alteration or damage to the Product caused by accident, neglect, or misuse. OTHER THAN IN THE CASE OF DEATH OR PERSONAL INJURY CAUSED BY ITS NEGLIGENCE AND EXCEPT WHERE PROHIBITED BY LAW, IN NO EVENT SHALL 3M BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL LOSS OR DAMAGES (INCLUDING LOST PROFITS) ARISING FROM THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ASSERTED. Electrical Markets Division (EMD) 3M United Kingdom plc 23 Standard Way Industrial Estate Northallerton North Yorkshire DL6 2XA United Kingdom Phone: +44 (0) Electrical Markets Division (EMD) 3M United Kingdom plc 3M Centre Cain Road, Bracknell Berkshire RG12 8HT Phone: Fax: Please recycle. Printed in UK. 3M All rights reserved. - 06/14 6
3M Scotchkote System Application Guide. High Performance Corrosion Resistant System for Plastisol Coated Metal Cladding
High Performance Corrosion Resistant System for Plastisol Coated Metal Cladding - Issue 1 Surface Preparation & Cleaning Application of Patch Primer to Corroded Areas Application of Primer to Patch Primed
More informationThese Application Instructions cover surface preparation, application equipment and application details for HEMPADUR MASTIC 45880/45881.
For product description refer to product data sheet HEMPADUR MASTIC 45880/ HEMPADUR MASTIC 45880/ High temperatures: 45881: BASE 45889 with CURING AGENT 95881 Low to medium temperatures: 45880: BASE 45889
More informationFinal Polish of Fiber Optic Connectors using 3M Lapping Films 863X and 863XW on Seikoh Giken SFP-550 Polishing Machines
of Fiber Optic Connectors using 3M Lapping Films 863X and 863XW on Seikoh Giken SFP-550 Polishing Machines Technical Application Bulletin October, 2005 General Information The 3M Lapping Films 863X and
More informationControltac Plus. Graphic Film RG Product Bulletin RG Description. Compatible Products. For Piezo Ink Jet Printing Only
Controltac Plus Graphic Film RG162-10 Product Bulletin RG162-10 Release UKB, Effective Aug06 See Bulletin Change Summary on last page Description 3M Controltac Plus Graphic Film RG162-10 is a 4 -mil positionable
More informationFinal Polish of Fiber Optic Connectors using 3M Lapping Films 863X and 863XW on Seiko Instruments SII, OFL-12 and OFL-15 Polishing Machines
of Fiber Optic Connectors using 3M Lapping Films 863X and 863XW on Seiko Instruments SII, OFL-12 and OFL-15 Polishing Machines Technical Application Bulletin June, 2005 General Information The 3M Lapping
More informationDULUX UNIVERSAL UNDERCOAT
TECHNICAL DATA SHEET Version 1 2015 JUNE THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION Intermediate coating for use under decorative topcoats, for interior and exterior use PRODUCT
More informationFinal Polish of Fiber Optic Connectors using 3M Lapping Films 863X and 863XW on Domaille Engineering Polishing Machines
of Fiber Optic Connectors using 3M Lapping Films 863X and 863XW on Domaille Engineering Polishing Machines Technical Application Bulletin June, 2005 General Information The 3M Lapping Films 863X and 863XW
More information3M Scotchlok Insulated Electrical Spring Connector B (Blue)
3M Scotchlok Insulated Electrical Spring Connector B (Blue) Data Sheet November 2008 Application Use 3M Scotchlok Insulated Electrical Spring Connector B (Blue) to electrically connect two or more conductor
More information3M XYZ-Axis Electrically Conductive Adhesive Transfer Tape (ECATT) 9723
Technical Data November, 2009 M XYZ-Axis Electrically Conductive Adhesive Transfer Tape (ECATT) 972 Product Description M XYZ-Axis Electrically Conductive Adhesive Transfer Tape (ECATT) 972 is an isotropically
More informationThe Path to a Perfect Finish
For more information contact your M representative, authorized distributor or visit MMarine.com Individual Product Instruction and Safety Information For individual product instructions and applicable
More informationThe Path to a Perfect Finish. A guide to our most advanced line of gelcoat and paint refinishing products.
The Path to a Perfect Finish A guide to our most advanced line of gelcoat and paint refinishing products. 1 Visit 3MMarine.com/buffing for more detailed product selection help. Choosing the right product
More informationWSS-M99P48-A3: 3 Foam Performance, PressureSensitive Adhesive Tape. Pressure Sensitive Adhesive Tape (Interior, Exteriorand Underhood Applications)
W-M99P48-A3: 3 W-M99P48-A3 Pressure Sensitive Adhesive Tape (Interior, Exteriorand Underhood Applications) Technical Bulletin November, 2016 3M tested the following adhesive tapes to the Automotive OEM
More informationTechnical Data February, 2016
Technical Data February, 2016 Product Description 3M DP-600 is a non-sag, grey, rapid setting, two-component polyurethane. It is packaged as 1:1 ratio liquids in a duo-pak cartridge. With the squeeze of
More informationSEA45 Water Borne Acrylic Gloss
Water Borne Acrylic Gloss TECHNICAL DATA SHEET Product Description Components is a single pack, general purpose gloss finish. Applicable by brush or spray. Fast drying Water based, low VOC Excellent weather
More informationEpoxy Coal Tar. Protects Steel and Concrete in Marine and Industrial Environments.
Epoxy Coal Tar Protects Steel and Concrete in Marine and Industrial Environments. General Epoxy Coal Tar is a protective coating designed to resist chemical attack and rigorous weather conditions by combining
More informationOWENS FLOORING LLC MAINTENANCE AND WARRANTY
OWENS FLOORING LLC MAINTENANCE AND WARRANTY Wood Floor Care and Maintenance Your new wood floor is an important investment, and must be properly cared for and maintained in order for you to enjoy its full
More informationMarch 2009 Product Information RAPID GREYMATIC 2K Filler
GLOBAL REFINISH SYSTEM March 2009 Product Information RAPID GREYMATIC 2K Filler PRODUCT DESCRIPTION 2K RAPID GreyMatic is a range of 2K primer surfacers suitable for a wide range of repair work. Versatile,
More informationLUXAPOOL EPOXY POOL COATING APPLICATION GUIDE. New Cement Pools
LUXAPOOL EPOXY POOL COATING APPLICATION GUIDE New Cement Pools 1. The render should consist of fresh cement and pure, clean sand only. Allow the render to cure for a minimum of 21 days prior to any preparation
More informationAPPLICATION NOTE - SR001. Cold Weather Application
APPLICATION NOTE - SR001 Cold Weather Application Silent Running is best applied with the ambient, material and substrate temperature in the range of 65-85 degrees F. Lower temperatures will result in
More informationNOTE: This product can be used externally if UV Guard is added (BY REQUEST ONLY).
Product Description PHOENIX PAINTS MAXICOAT 100 is a 2 Pack Water-Dispersed Top Coat which not only exhibits the physical and chemical strengths of epoxy, but also the safety and convenience of water as
More informationAPPLICATION NOTE - SR001. Cold Weather Application
APPLICATION NOTE - SR001 Cold Weather Application Silent Running is best applied with the ambient, material and substrate temperature in the range of 65-85 degrees F. Lower temperatures will result in
More information3M Contrast Enhancement Film. The. Clear. Advantage. High purity, optical-grade adhesive films for joining transparent materials
3M Contrast Enhancement Film The Clear Advantage High purity, optical-grade adhesive films for joining transparent materials 3 3M Contrast Enhancement Film Engineered to speed assembly, improve display
More informationPRODUCT GUIDE: CATALYZED TOPCOATS. Version:
PRODUCT GUIDE: CATALYZED TOPCOATS Version: 08.07.17 ELITE COATINGS PRODUCT DATA PRODUCT: Low VOC High Solids Aliphatic Urethane Product Number: 4045 DESCRIPTION: 4045 is a top of the line 2 component urethane
More informationBRUSH APPLICATION INSTRUCTIONS
QUALITY MARINE EQUIPMENT SINCE 1981 Antifouling Paint For Metal Under The Waterline BRUSH APPLICATION INSTRUCTIONS www.antifoulingpaint.net TABLE OF CONTENTS Humidity & Drying Metal Surfaces... 1 Coverage
More informationPBWWinc. GEN-U-LINE 4000 Series Application Guide. Technical Data Sheet. General Guidelines:
PBWWinc. 1 GEN-U-LINE 4000 Series Application Guide Technical Data Sheet General Guidelines: 1) Close the facility to all traffic before starting any work on the game lines. Close all doors and windows
More informationRAPTOR EPOXY PRIMER RAPTOR 4:1 ANTI-CORROSIVE EPOXY PRIMER DESCRIPTION
Suitable as a primer or as a primer filler for industrial refinish applications, the primer also provides excellent anti-rust protection. Easy to apply Excellent anti-corrosion resistance Can be applied
More informationGeneral description: Two-component high-build, high solids surface tolerant universal epoxy coating. For painting on steel and galvanized steel substrates. Certified for systems category C5I High ISO 12944.
More information3M Abrasive Systems. Sanding made simple.
3M Abrasive Systems Sanding made simple. Introducing Sanding Made Simple. For more than 100 years, 3M Science has provided technologies designed to make your life easier and improve the world one finish
More informationHigh-quality, water-dilutable satin gloss enamel on the basis of a modified alkyd technology.
Product Data Sheet High-quality, water-dilutable satin gloss enamel on the basis of a modified alkyd technology. ralstoncolour.com /picto Excellent outdoor resistance Excellent flow and optimal hiding
More informationQuality Marine Equipment Since Antifouling Paint For Metal Under The Waterline ROLLER. Application Instructions.
Quality Marine Equipment Since 1981 Antifouling Paint For Metal Under The Waterline ROLLER Application Instructions www.antifoulingpaint.net THANK YOU! Thank you for selecting Velox Plus Antifouling Paint
More informationTechnical Data April Product Facestock Adhesive Liner. 3M Sheet Label.002 in. Bright Silver 350 Acrylic 90# Polyctd.
3 Sheet Label Material 7903 7905 7908 7909T 7903FL 7908FL Technical Data April 2017 Product Description 3M Sheet Label Materials are durable, high performance materials that offer excellent thermal stability,
More informationPrimer Surfacer EP II
Description Surfacer EP II is a gray, 4.6 lbs/gal, chromate-free epoxy primer that can be applied as a sprayable sanding surfacer, rollable sanding surfacer or primer sealer. This product provides good
More information3M Electrically Conductive Double-Sided Nonwoven Tape 9750
Technical Data October 2013 3M Electrically Conductive Double-Sided Nonwoven Tape 9750 Product Description 3M Electrically Conductive Double-Sided Nonwoven Tape 9750 is an isotropically electrical conductive
More information3M Impact Protection Profile Installation System Instructions
3M Impact Protection Profile Installation System Instructions IMPORTANT: READ INSTRUCTIONS FOR USE BEFORE OPERATING Intended Use: The 3M Impact Protection Profile Installation System is for installing
More informationwall thinning) can be lower. Wall thinning is determined by part shape and depth of draw. Please contact your 3M representative for more information.
3M Custom Formed Reflectors increase the optical efficiency of a light fixture by using precise reflection optics to raise the lumen output. Each reflector is custom designed to your specifications for
More informationautomatic embosser & die cutter USER MANUAL
TM TM automatic embosser & die cutter USER MANUAL CREATE A BEAUTIFUL LIFE IN THE BOX Cut n Boss machine (7) Embossing Folders (12) Cutting Dies Platforms (2) (1) Platform B (1) Platform D Magnetic Shim
More informationmm bar at the air inlet minutes at 20 C 5-10 minutes at 20 C. 8 hours at 20 C 45 minutes at 60 C 3 coat application
Description Two-pack, VOC compliant, chromate-free epoxy primer-surfacer with good adhesion and corrosion resistance properties on all substrates within the Car Refinish market. For both new panels and
More informationPRODUCT GUIDE: CATALYZED PRIMERS. Version:
PRODUCT GUIDE: CATALYZED PRIMERS Version: 08.07.17 305 Zinc Rich Epoxy Polyamide Primer Description: 305 is a user friendly zinc-rich epoxy primer formulated for use as a primer under acrylic, epoxy, and
More informationCushion-Mount Plus Plate Mounting Tapes with Easy Mount Adhesive L1820 L1720 L1520 L1020 L1320 L1920, L1920S L1220 L1120
Cushion-Mount Plus Plate Mounting Tapes with Easy Mount Adhesive L1820 L1720 L1520 L1020 L1320 L1920, L1920S L1220 L1120 Technical Data January, 2015 Product Description 3M Cushion-Mount Plus Plate Mounting
More informationPBWWinc. Technical Data Sheet. GERLINE Gameline Paint Instructions for Sport Flooring. General Guidelines:
PBWWinc. 1 Technical Data Sheet GERLINE Gameline Paint Instructions for Sport Flooring General Guidelines: 1) Close the facility to all traffic before starting any work on the game lines. Close all doors
More informationSuggested Specification for Preparing Hot-Dip Galvanized Steel Surfaces for Painting Revised February 2002
Suggested Specification for Preparing Hot-Dip Galvanized Steel Surfaces for Painting Revised February 2002 This suggested specification is provided as a guide to preparing a quality document calling for
More informationTechnical Data July, 2010
3 Cushion-Mount Plus Plate Mounting Tapes with Easy Mount Adhesive High Plateside Adhesion E1815H, E1820H E1715H, E1720H E1515H, E1520H E1015H, E1020H, E1040H, E1060H E1315H, E1320H E1915H, E1915HS, E1920H,
More information2K weather resistance clear coat A850
Clear coat Donglai Coating Technology (Shanghai) Co., Ltd. 2K weather resistance clear coat A850 Description High-build, two-component clear coat designed for universal application and optimal appearance
More informationThe required quality of surface preparation can vary depending on the area of use, expected durability and if applicable, project specification.
Technical Data Sheet 402;2521 1 2521 zinc silicate VValidationDate). 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a very high zinc dust containing product.
More informationQuality Marine Equipment Since Antifouling Paint For Metal Under The Waterline SPRAY. Application Instructions.
Quality Marine Equipment Since 1981 Antifouling Paint For Metal Under The Waterline SPRAY Application Instructions www.antifoulingpaint.net Thank you for selecting Velox Plus Antifouling Paint to protect
More informationKnowledge Requirements. Protective Coatings Applicator Abrasive Blast Cleaning Operator Spray Painting Operator. trainthepainter.
Knowledge Requirements Protective Coatings Applicator Abrasive Blast Cleaning Operator Spray Painting Operator trainthepainter.com Knowledge Requirements The Knowledge Requirements the protective coatings
More informationWEGTHANE HPA 501 (HPA 501/ HPA 502/ HPA 503/ HPA 504)
WEGTHANE HPA 501 (HPA 501/ HPA 502/ HPA 503/ HPA 504) PRODUCT DESCRIPTION: INTENDED USES: Bicomponent gloss aliphatic acrylic polyurethane finishing paint, with excellent durability and extended repainting.
More informationCUPRON NEXT TECHNICAL DATA SHEET
Product description New hard matrix antifouling paint free of copper and organostannic compounds. It provides good seasonal protection for boats that work even in particularly hot and aggressive waters.
More information380 Swimming Pool Paint
Issued 21 st April 2010 PRODUCT DATA SHEET UNPAINTED CEMENT 380 Swimming Pool Paint SURFACE PREPARATION New cement or render should be allowed to cure for at least 21-28 days before any preparation is
More information15 Planer Stand. Model Due to continuing improvements, actual product may differ slightly from the product described herein.
15 Planer Stand Model 96316 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo,
More informationThe Application Guide offers product details and recommended practices for the use of the product.
Technical Data Sheet Application Guide Approved 402;2522 1,2 2522 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high zinc dust
More informationSignal Integrity Product Specification
PD--0077 Signal Integrity Product Specification 3M SFP+ Passive Direct Attach Copper Cable Assembly 3 Electronic Solutions Division Page: 1 of 9 Table of Contents 1.0 Scope... 4 2.0 Product Tested... 4
More informationPRODUCT DESCRIPTION High quality interior or exterior enamel for surfaces where a glossy durable finish is required
TECHNICAL DATA SHEET Version 1 2016 JULY THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION High quality interior or exterior enamel for surfaces where a glossy durable finish is required
More informationHAMMERITE DIRECT TO RUST HAMMERED AND SMOOTH
TECHNICAL DATA SHEET Version 1 2016 June THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION A corrosion resistant and decorative coating for ferrous and nonferrous metals, wood and certain
More informationProduct Bulletin
3M Controltac Chrome Graphic Graphic Film Film 3635-110 Product Description 3-mil translucent film that reflects light to produce a glossy chrome appearance in a finished graphic Product Features Medium
More information3M Power Clamp Wiremount Connectors
Instructions Scope: This document describes the termination instructions for 3M Power Clamp Wiremount Connectors Series 355 and 358. 3M Part Numbers 35505-6XX0-XXX XX 35805-6XX0-XXX XX Applicable Documents:
More informationAquaCLAD Water-Reducible Rust Preventative Alkyd
AquaCLAD 1600 Water-Reducible Rust Preventative Alkyd A rust preventative coating for interior and exterior steel in mild to moderate industrial environment. Recommended For Features Refinish Market High
More informationControltac Graphic Film
Controltac Graphic Film 162-10 and 162-114 Product Bulletin 162 Release L, December 2008 See Bulletin Change Summary on last page. For Screen Printing and Offset Printing Only Product Description Recommended
More informationMix Ratio (by volume) 7630/3600 (Base) 0830/9000 (Acid Catalyst) Metal Primer 6840B meets the technical requirements of: Mil-P-7962 Mil-C-15328
TECHNICAL DATA SHEET Product Description 6840B is a two component chromated etch primer designed to give adhesion and corrosion protection to aluminium alloys as part of the 4080 series scheme. Alternative
More informationProduct Information DP5000
GLOBAL REFINISH SYSTEM March 2016 Product Information DP5000 (For use with UHS Hardener) PRODUCT DESCRIPTION D8521 Light Grey D8525 Grey D8527 Dark Grey UHS Hardener D8717/18/19 Thinners DP5000 is a range
More informationA-LF-Sea. Application Manual for M&R. (Full blasting)
Application Manual for M&R (Full blasting) April 2015 1 Contents 1.Standard scheme 1)Standard scheme for flat & vertical bottom 2)Colour scheme for system 2.High pressure fresh water washing (HPFWW) 1)Timing
More informationSELECTION AND PREPARATION OF SUBSTRATES
592 TECHNICAL DATASHEET 7-538 / 7-539 SELEMIX DIRECT GLOSS TOPCOATS PRODUCT DESCRIPTION Selemix Direct Gloss are polyurethane coatings based on PU 2K technology, which can be applied direct onto substrates
More informationHP Chromate Free Epoxy Primer P /-4505/-4510
Product Data Sheet September 2011 (February 2013 update) INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY HP Chromate Free Epoxy Primers P580-4501/-4505/-4510 Product Description P580-4501 HP Chromate Free
More informationLow V.O.C. 2-Component Polyurethane Game Line Paint System
PBWWinc. 1 Technical Data Sheet GEN-U-LINE 4000 Series Low V.O.C. 2-Component Polyurethane Game Line Paint System Product Description: GEN-U-LINE 2-component polyurethane line paints are high gloss, flexible,
More informationBig Sky Product Information Sheet. Epoxy Prime Primer/Sealer PS3042 (Lt. Gray) PS3044 (Dk. Gray) PS3045 (Black) PS3047 (Yellow Oxide)
Big Sky Product Information Sheet TECHNICAL SUPPORT ((800) 328-4892 P.I. Sheet #3008 Epoxy Prime Primer/Sealer PS3042 (Lt. Gray) PS3044 (Dk. Gray) PS3045 (Black) PS3047 (Yellow Oxide) READ ENTIRE PRODUCT
More information380 Swimming Pool Paint
Issued 21 st June 2011 PRODUCT DATA SHEET 380 Swimming Pool Paint SURFACE PREPARATION If your pool has been previously painted but you are unsure as to whether or not it was with chlorinated rubber or
More informationProduct Data Sheet November 2016
Product Data Sheet November 2016 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY T8500V HP Chromate Free Epoxy Primer P580-3501/-3502/-3503/-3504 Product Description P580-3501 HP Chromate Free Epoxy Primer
More information3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE Cabinet Mounting with Stakes, Installation Guide
3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE Cabinet Mounting with Stakes, Installation Guide Installing a cabinet with stakes Instructions July 2016 78-0015-3106-6 2 July 2016 78-0015-3106-6
More information3 Shielded Compact Ribbon (SCR) Wiremount Plug, XX, and Shell Kit, F200-XXX
3 Shielded Compact Ribbon (SCR) Wiremount Plug, 36110-3000XX, and Shell Kit, 36310-F200-XXX Instructions June 2007 78-9100-4282-5 General This instruction manual explains the method of assembling the 3M
More informationSignal Integrity Test Report
PD-0098 Signal Integrity Test Report 3M External MiniSAS Cable Assemblies 3 Electronic Solutions Division Subject: 3M External MiniSAS Cable Assembly Page: 1 of 14 Table of Contents 1.0 Scope... 2 2.0
More informationInstruction Sheet REB SERIES. Rotating Sliding Base REB18
Instruction Sheet REB SERIES Rotating Sliding Base REB14 REB18 THANK YOU Thank you for purchasing the REB Series Rotating Sliding Base. Please read these instructions thoroughly before installing this
More informationnax Urethane Primer Surfacer Zitan
Description Quick-drying two-pack wet on wet primer surfacer and sanding primer filler with excellent application and sanding properties. Helps to reduce process time due to its wide application window
More informationTechnical Data June, 2008
3 Cushion-Mount Plus Easy Mount Tapes with High Plateside Adhesion E1815H, E1820H E1715H, E1720H E1515H, E1520H E1015H, E1020H, E1040H, E1060H E1315H, E1320H E1915H, E1920H, E1920HS E1215H, E1220H, E1115H,
More informationJanuary 2007 Product Information DELTRON D821
GLOBAL REFINISH SYSTEM January 2007 Product Information DELTRON High Solids Chip Resistant Primer PRODUCT DESCRIPTION is a transparent-grey primer surfacer with excellent anti-chip and anti-corrosion properties.
More informationDuraguard ULTRA PREMIUM MATT DATA SHEET FC Description & Uses. Features & Benefits. Colours. Environmental Data & Certifications
PAGE 1 OF 5 Description & Uses Solver Duraguard Matt is an ultra premium quality, 100% acrylic, self priming exterior water-based coating, suitable for direct application to most surfaces including timber,
More informationPlanishing hammer stand For use with SKU Planishing hammer
Planishing hammer stand For use with SKU 94847 Planishing hammer Model 96300 Assembly And Operation Instructions Please Note: Planishing Hammer not included with Stand. Due to continuing improvements,
More informationHarrogate Care Guide. Information. By Neptune. neptune.com
Information We are delighted that you have chosen to purchase one of our Harrogate pieces of furniture. Whether it is a classically designed dining table or an elegant free standing cabinet, we are sure
More information5543/9000 Flame Retardant UV Resistant Varnish High Gloss
Flame Retardant UV Resistant Varnish High Gloss TECHNICAL DATA SHEET Product Description is a two component, transparent, glossy acrylic urethane varnish. Designed to provide UV protection to external
More informationDescription. Product Line. Packaging. Storage. Instruction Bulletin 3.12 (UK)
Instruction Bulletin 3.12 (UK) Release (UK-B) July 2000 Screen Printing with 3M Screen Printing Ink Series 1900 (Line Inks) Description The 3M Screen Printing Ink Series 1900 are used on 3M Controltac
More informationPainting Pitched Roofs
4 Tutorial 4 Painting Pitched Roofs Tile & Galvanized Iron Paint Academy Determining your product requirement: Measure area to which paint is to be applied. Depending on surface to which the product is
More informationProduct Information PRIMA D839 2 Component Primer
GLOBAL REFINISH SYSTEM March 2011 Product Information PRIMA 2 Component Primer PRODUCT DESCRIPTION Prima is a grey 2K primer surfacer, suitable for a wide range of day-to-day repair work. Versatile, quick
More informationHP Epoxy Primer P
Product Data Sheet September 2006 (updated November 2016) INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY HP Epoxy Primer P580-3005 Product Description P580-3005 HP Epoxy Primer P275-3022 Hardener for Epoxy
More informationINSTALLATION & OPERATING INSTRUCTIONS. REDCO LETTUCE KING I and LETTUCE KING IV
INSTALLATION & OPERATING INSTRUCTIONS for REDCO LETTUCE KING I and LETTUCE KING IV Lettuce King I Shown with optional Drum Ring Lettuce King IV TO BE SERVICED ONLY BY AUTHORIZED PERSONS P/N: 2802381 REV:
More informationProduct Data Sheet August 2006 (Updated in December 2014)
Product Data Sheet August 2006 (Updated in December 2014) INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY Fastbuild TM Product Description P540-400 Fastbuild - green P540-401 - off white P540-402 - grey
More informationPRODUCT GUIDE: COMPLIANT TOPCOATS. Version:
PRODUCT GUIDE: COMPLIANT TOPCOATS Version: 08.07.17 EAGLE BRIDGES PRODUCT DATA PRODUCT: 3.5 V.O.C FASTDRY, Black Product Number: 4899 DESCRIPTION: This product is a high gloss enamel for OEM finishing
More information3M Air and Vapour Barrier 3015 Technical guide
3M Air and Vapour Barrier 3015 Technical guide Product overview Typical physical properties For installation ease and flexibility, 3M Air and Vapour Barrier 3015 High performance 3M acrylic adhesive grabs
More informationScotchcal Series 7725 SE
Scotchcal Series 7725 SE Special Effects Film Product Bulletin 7725 SE (UK) Release UK-J, Effective July 2004 Description Applications and Uses 3M Scotchcal Special Effects Film Series 7725 SE is intended
More informationAerodur 3001 Base Coat Special Effects
Technical Data Sheet Product Group Polyurethane Topcoats Characteristics Product Information Aerodur 3001 topcoat is part of the high solid 3 components polyurethane Aerodur 3001 Solid Colors Aerodur 3001
More informationFull Product Name. Products. Properties. 2K Etch Primer. Type of Product Description
Product Name Full Product Name Type of Product Description 2K acid etch primer Concept is an acid containing etch and primer in one product. This Product is characterized by excellent adhesion and corrosion
More informationDELIVERING A COMPETITIVE ADVANTAGE. A Guide to 3M Products and Converter Capabilities FOR YOUR MANUFACTURING NEEDS
DELIVERING A COMPETITIVE ADVANTAGE. A Guide to 3M Products and Converter Capabilities FOR YOUR MANUFACTURING NEEDS OF PARTNERSHIP There s no question that today s manufacturing marketplace is extremely
More informationThe Application Guide offers product details and recommended practices for the use of the product.
Technical Data Sheet Application Guide Approved 765 1,2 765 vinyl ^(ValidationDate) 1 Product description This is a one component physically drying vinyl coating. It is fast drying. Can be used as primer
More informationLamination Techniques for Converters
3 Lamination Techniques for Converters Technical Bulletin April, 2017 Lamination Process Basic Requirements for Good Results 1. Clean substrates. 2. Selection of best adhesive for the job. 3. Proper equipment
More informationSingle Flex and Double Flex Couplings (i)
Single Flex and Double Flex Couplings (i) FORM NO. L00G00 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are subject to change
More informationVolume Solids % Weight Solids %
Product Name Full Product Name Type of Product Description HS 2K Primer (High Build) 2K high build acrylic urethane primer surfacer Concept HS 2K Primer (High Build) is a high solid 2K acrylic urethane
More informationTechnical Data Sheet August 2017
Technical Data Sheet August 2017 Consumer Solutions Products Description Consumer Solutions Products are designed for use on safety garments and in athletic and casual wear. When properly used, Scotchlite
More informationnax Pro LV3601/03/05 VHS Primer Surfacer
Description VOC compliant, quick-drying multi grey shade, two-pack wet on wet and sanding primer surfacer, with excellent application and sanding properties. Helps to reduce process time and provides good
More information3M Locator Plate
M Locator Plate 44-119 Instructions for the Assembly of Series 158 2 mm x 2 mm Socket Connectors 1.0 General The Locator Plate 44-119 is designed for rapid assembly of all available pin count positions
More informationWarranty Terms & Conditions
Warranty Terms & Conditions Is my guitar under warranty? How long, what specific parts? Ibanez Electric Guitars and Basses Limited Warranty Ibanez Electric Guitars and Basses sold in the United States
More information2001A. 200KHz Function Generator Instruction Manual. 99 Washington Street Melrose, MA Phone Toll Free
2001A 200KHz Function Generator Instruction Manual 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com WARRANTY Global Specialties
More information30 Bending Brake. Model Assembly and Operating Instructions. Distributed exclusively by Harbor Freight Tools.
30 Bending Brake Model 41311 Assembly and Operating Instructions Distributed exclusively by Harbor Freight Tools. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Copyright 1999 by Harbor Freight Tools. All
More information