Loudspeaker XY Series Installation manual

Transcription

1 Loudspeaker XY Series Installation manual XY-122 XY-81 XY-118S XY-215S 12-inch two-way loudspeaker 8-inch two-way loudspeaker 18-inch bass reflex Subwoofer Dual 15-inch quasi-bandpass subwoofer Version 1.0 Feb PIONEER CORPORATION All right reserved

2 Contents 1 Introduction 2 Accessories 3 Rigging Setting 3.1 XY XY XY-118S 3.4 XY-215S 4 System Configuration 4.1 Connections 4.2 System setting 5 Drive unit replacement 5.1 XY XY XY-118S 5.4 XY-215S 6 Specifications 6.1 Spec sheet 6.2 drawing

3 1 Introduction WARNING Certain technical skills are required to install the loudspeaker. Please have the product installed by a professional. Pioneer is not responsible for any loss or damage that results from improper installation, insufficient strength of installation materials, misuse, modification or natural disasters. 1.1 Before you start CAUTION: installation Ensure that the floor or stage surface can withstand the weight of the system. The installation technician must follow professional installation techniques to protect the loudspeaker against falling. When installing the speakers, make sure that the wall/ceiling is strong enough to support the speakers. Do not install the loudspeaker in areas exposed to direct sunlight or near heating appliances. Such conditions may result in shrinkage of the wood materials and finish, leading to deformation of the enclosure, discolouration, or damage to the speakers. Conditions considered unpleasant by humans are detrimental to speakers as well. Providing a comfortable environment for the speakers will assist them in demonstrating their best performance. Please maintain the usage environment as follows: Temperature: 15 C to 25 C (59 F to 77 F) Relative Humidity: 35 % to 65 % (winter) 40 % to 70 % (summer) Do not store speakers at temperatures outside of the rated temperature range as doing so may cause the speaker to drop in performance or become damaged. Storage temperature range: 20 C to +55 C ( 4 F to +131 F) Do not use the product in locations subject to extreme fluctuations in temperature. Doing so could cause the product to malfunction. This loudspeaker must be installed by a qualified technician as it involves such tasks as selecting a location for installation, drilling holes in walls/ceiling and wiring. Have the installer carefully follow the installation instructions. Make sure to use amplifiers with rated load impedances that match the speaker impedance for the amplifiers connected to each loudspeaker. Furthermore, any devices or objects easily affected by magnetism (floppy disks, magnetic cards, magnetic tape etc.) should be kept well away from the speakers. In order to prevent damage to the loudspeaker resulting from input overload, please observe the following precautions: If you supply amplification power to the loudspeaker excessively, the speaker could be damaged and overheating could cause a hazard. Only connect, turn ON or OFF the audio system or any one part (such as DJ player and Mixer) when the power to the amplifier is turned off. If any operations are performed while the amplifier is turned on, there is the possibility of damaging the treble frequency speaker unit. When using a graphic equaliser to emphasise loud sounds in the high-frequency range, do not use excessive amplifier volume. Do not try to force a low-powered amplifier to produce high sound levels as the amplifier s harmonic distortion will be increased, and you may damage the speaker. Improper installation of the speakers could cause them to fall and cause damage or injuries to persons nearby. Do not attempt to stack devices together for use other than specified systems. Such devices may become unstable and tip over or fall, leading to injury. Make sure to secure each device in place using the pole mount, ratchet straps or other hardware to prevent them from tipping over or falling when stacking devices together. Pioneer shall accept no liability for damage or injury caused by accidents resulting from Pioneer products tipping over or falling due to them being insufficiently secured. Switch off and unplug your power amplifier and consult the instructions when connecting up components. Make sure you use the correct connecting cables. Keep magnetic objects such as screwdrivers or steel parts away from the tweeter and woofer speakers. Since the speakers use strong magnets, the objects may be attracted, causing injury or damaging the diaphragm. When using room air-conditioners or stoves to rapidly cool or heat room spaces, take precautions to avoid excessive dehumidification. Avoid placing the speaker near areas such as windows, as outside air can cause condensation to occur within the speaker. This loudspeaker is designed for indoor use only. To avoid electric shock hazard, do not place them outside, or in an overly humid area.

4 CAUTION: in use Do not use the speaker to output distorted sound for long periods of times. This can result in a fire hazard. Please also remember that vibrations from subwoofer systems can shake other loudspeakers out of place, which may present a toppling hazard. Do not attempt to use the product with the XY Series grille detached as doing so could result in damage to the product. Consult a qualified professional for assistance with removing the grille for maintenance purposes. For Europe If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one). For countries not mentioned above, please contact your local authorities for the correct method of disposal. By doing so you will ensure that your discarded product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health. The Safety of Your Ears is in Your Hands Get the most out of your equipment by playing it at a safe level a level that lets the sound come through clearly without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Sound can be deceiving. Over time, your hearing comfort level adapts to higher volumes of sound, so what sounds normal can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts. ESTABLISH A SAFE LEVEL: Set your volume control at a low setting. Slowly increase the sound until you can hear it comfortably and clearly, without distortion. Once you have established a comfortable sound level, set the dial and leave it there. BE SURE TO OBSERVE THE FOLLOWING GUIDELINES: Do not turn up the volume so high that you can t hear what s around you. Use caution or temporarily discontinue use in potentially hazardous situations. Do not use headphones while operating a motorised vehicle; the use of headphones may create a traffic hazard and is illegal in many areas. About trademarks and registered trademarks Pioneer is a registered trademark of PIONEER CORPORATION. SpeakON is a registered trademark of Neutrik. The names of companies and products mentioned herein are the trademarks of their respective owners.

5 1.2 Installation guidelines WARNING Ensure that the floor or stage surface in question can withstand the weight of the system. Consult a qualified professional for advice if the strength of the surface is unknown. After installation, you must confirm that the speakers are safely installed. You must also periodically check them to make sure that they are still safe. Wherever possible, avoid high stacks and use ratchet straps to secure loudspeakers together. Please also remember that vibrations from subwoofer systems can shake other loudspeakers out of place, which may present a toppling hazard. The use of ratchet straps and non-slip material is recommended to prevent this. When this product is placed in an elevated place such as on a shelf or stage, a speaker may be moved by vibrations and fall to the floor, causing an injury or accident. Take measures to prevent a speaker from sliding off a shelf or a stage, etc. Full-range loudspeakers The XY-122 and XY-81 come with pre-inserted mounting screws. These screws can be taken out and used to attach either special mounting hardware designed for the product or commercially available mounting hardware. Make sure to attach a wire for preventing falling parts and equipment of adequate strength using screw holes not used by mounting hardware. WARNING When attaching the speakers to the wall or ceiling, you should first confirm that the wall or ceiling being used is strong enough to support their weight. If you are unsure then consult a specialist. If the speakers should fall then it could lead to serious injury, and is potentially very dangerous. Check to make sure that any mounting hardware used is enough to support the system, whether using special hardware designed for the system or commercially available hardware. Make sure to read the Introduction section in this manual and the instruction manual for the mounting hardware thoroughly before proceeding. Take every precaution to prevent the product and associated parts from falling as they could cause serious injury if they fell onto a person. Use screws suitable for ceiling material and screw mounting parts in solid locations. Make sure to use mounting hardware of sufficient strength to secure the speaker in place when using non-designated hardware. The speaker could fall, causing accidents,if not properly secured. The fall prevention wire must be attached to a suitably strong location. The strength of the location to which the wire is attached being insufficient can lead to the speakers falling or cause accidents. The fall prevention wire and screw to attach the fall prevention wire to the ceiling or wall are not supplied with the speakers, so please purchase them separately. Subwoofers A pole mount can be attached to the XY-118S and XY-215S. The pole mount can be attached by inserting and screwing it into the holes. WARNING Check to make sure that any mounting hardware used is enough to support the system, when using commercially available hardware. Make sure to read the Introduction section in this manual and the instruction manual for the mounting hardware thoroughly before proceeding. Be careful not to place any devices or other equipment on top of the system as such devices could fall, causing severe injury. Make sure to install the system in a stable location if using a pole for mounting. Make sure to use mounting hardware of sufficient strength to secure the speaker in place. The speaker could fall, causing accidents, if not properly secured.

6 1.3 System set-up WARNING Loudspeaker systems are potentially dangerous objects if used incorrectly. Please ensure that you read this section fully, and contact your local dealer should you be in any doubt over correct operation procedures. Professional loudspeaker systems are capable of producing damage-inducing sound pressure levels, and hence care should be taken when setting your system up, particularly when it comes to loudspeaker placement within a venue. Damage to the ear can result from levels above 90 db under prolonged exposure. Stand mounting The XY-122 and XY-81 can be mounted from a loudspeaker stand using the integral polemount adapter for a standard 35 mm (1.4 in.) loudspeaker stand. When mounting in this way,please consider the following: Ensure your stand height is locked off and the tripod legs are positioned so as to be stable. Check the weight loading of your stands before attempting to mount the loudspeaker. Do not stack a second loudspeaker on top of the stand-mounted one. Ensure cables are run so as to leave enough slack to enable neat wiring, and thus reduce the risk of the speaker being pulled over. Loose cables should be covered or taped down wherever possible to reduce trip hazards. When using poles on top of subwoofer systems, please observe similar precautions. Pole-mounted full-range loudspeakers from the XY-118S and XY-215S The XY-118S and XY-215S can support other loudspeakers using an M20 threaded pole adapter. When mounting in this way, please consider the following: Ensure the M20 pole is screwed in tightly, your stand height is locked off and the system is stable. Do not stack a second loudspeaker on top of the stand-mounted one. Note: Ensure cables are run so as to leave enough slack to enable neat wiring, and thus reduce the risk of the speaker being pulled over. Loose cables should be covered or taped down wherever possible to reduce trip hazards. When you want to combine the XY-122 or XY-81 enclosure with the XY-118S or Y-215S enclosure, ensure you use a commercially-available pole, where one of the edge is M20 threaded and the other is 35mm diameter as shown below. XY-118S XY-215S XY-122 XY-81 XY-118S/XY-215S M20 screw threaded pole socket XY-122/XY-81 bottom 35mm pole socket M20 screw threaded pole 35mm pole

7 2 Accessories Warning The overhead suspension of loudspeakers is a very serious issue with potentially lethal consequences should anything go wrong. Rigging should only be carried out by experienced personnel following safe working practice. Should you be in any doubt whatsoever, please contact the retailer or dealer from which you purchased this product. When utilising any suspension method, a secondary safety feature must be used. For any suspension method, fit an eyebolt to any of the rigging points. A safety steel can then be attached to this and connected to your safety point. Hardware standby The following hardware is provided with the XY series products so that commercially-available poles, brackets and other items can be attached. (see Table 2-1 "Hardware standby") Caution Accessories List Check to make sure that any commercially available mounting hardware used is enough to support the weight of the speaker system. If you use any commercially available eyebolt, ensure it is the same size as in the list below and have enough strength to withstand the weight of the loudspeaker. M10 x 30mm, P=1.5, Safe Working Load limits: 1.47[kN] (150[kg]) and more M8 x 15mm, P=1.25, Safe Working Load limits: 0.785[kN] (80[kg]) and more Please follow an instruction manual for a commercially available product for installation and safety measures. All the supplied accessories for XY series are listed in the following "Accessories List". (see Table 2-1 "Accessories List") Please ensure that you read "Section 1: Introduction" and "Section " fully, and have the product installed by a professional. Have the installer carefully follow the installation instructions.

8 Table 2-1 Wall Mount Bracket XY M8 threaded points XY-81 4 M6 threaded points XY118S - XY-215S - Eyebolts M10 (*2) M8(*3) - - Hardware standby Speaker Pole Tripod Stand 35 mm polemount socket 35 mm polemount socket 35 mm polemount socket 35 mm polemount socket M20 polemount socket - 2 x M20 polemount socket (top,right side) - Vertical Flying Cradle (*1) CP-XY12VC1 CP-XY8VC1 - - Horizontal Flying Cradle (*1) CP-XY12HC1 CP-XY8HC1 - - Accessories List Variable Angle Bracket (*1) CP-XY12AB Dual Enclosure Flying Plate Set (*1) CP-XY12DF Castor set - - CP-XYCS1 CP-XYCS1 Setting procedure Refer to Section 3.1 Refer to Section 3.2 Refer to Section 3.3 Refer to Section 3.4 *1 Eye bolts to be used as secondary safety feature are not included with the products. When you use any commercially available eyebolts, please use the eyebolts meeting the following size and specification. *2 M10 x 30mm, P=1.5, Safe Working Load limits: 1.47[kN] (150[kg]) and more *3 M8 x 15mm, P=1.25, Safe Working Load limits: 0.785[kN] (80[kg]) and more

9 3 Rigging Setting 3.1 XY-122 Mounting points are provided on the enclosures of XY-122 for the suspension purpose. A cradle or a commercially-available eyebolt can be mounted to a mounting point when the enclosure is installed to a ceiling or a wall. The Safe Working Load limits: 60 kg/mounting point at maximum WARNING: Do not use a method other than the one prescribed in this manual. CAUTION: EYEBOLT STRENGTH When you use any commercially-available eyebolts, please use the eyebolts meeting the following size and specification: M10 x 30mm, P=1.5, Safe Working Load limits: 1.47[kN] (150[kg]) or more. The safe working load limits of an eyebolt are different depending on an inclined angle of the wire attached to the eyebolt. If the suspension angle of the wire attached to the eyebolt is inclined (not vertical) and correctly oriented in the plane of pull, be sure to read the catalogue of the eye bolt for details of the safe working load limits depending on the inclined angle. It is generally recommended that an angle of the wire attached to the eye bolt correctly oriented in the plane of pull be 45 degrees at maximum. Do not suspend the eye bolts as shown here. PREPARING THE CABINET Pre-inserted M10 and M8 screws are mounted in the top, bottom, rear, left and right side of the loudspeaker enclosure. These screws are painted in the cabinet color. Follow the steps below to ensure the cabinet paint is not peeled off during unscrewing. (1) Make a small slit around the pre-inserted screws using an appropriate cutting knife. (2) Carefully remove the screws using a screwdriver, and ensure the cabinet coating is not peeled off. 0 ~ ±45 (1) (2)

10 3.1.1 Vertical Flying Cradle (CP-XY12VC1) When using the Vertical Flying Cradle (CP-XY12VC1), suspension of the XY-122 enclosure vertically from the ceiling as shown in the right figure is available. The weight of the Vertical Flying Cradle is 4.8 kg. To the ceiling CAUTION: Vertical Flying Cradle is not supposed to be used in the following situations, which may cause an injury or accident. The outer yoke of the cradle is not vertical to the ceiling The enclosure is not horizontal to the ceiling Suspending from the wall Suspending multiple enclosures

11 Part list Required tools Item Part Name Qty Service Part No. Note Screwdriver A Vertical Flying Cradle 1 - Outer Yoke 1 - Inner Yoke 1 - Neoprene Washer 2 05B011 60mm x 2mm Flat Washer 2 06D014 M10 Spring Washer 2 06D015 M10 8mm hex key Lever 2 05A103 M10 B M10 socket head bolt 3 06G052 M10 x 70mm (P=1.5), 8mm hex socket head C Spring Washer 3 06D015 M10 D Flat washer 3 06D014 M10 Procedure (1) Remove the two pre-inserted mounting screws from the top of XY-122. (Fig A) (2) Using the two M10 socket head bolts(b), align the mounting holes in the inner yoke of the Vertical Flying Cradle(A) with the mounting points on the top of the enclosure. Ensure that both the Flat Washer(D) and the Spring Washer(C) are used - the Flat Washer(D) should be in contact with the cradle. Tighten the bolts over 15N m torque. (Fig B) CAUTION *1) (3) Once the desired angle of the loudspeaker is set, tighten the levers on the cradle to lock the position in place. (Fig C) CAUTION *2) (4) The hole (φ13) on the outer yoke of the Vertical Flying Cradle(A) can be used to install the speaker to the ceiling. (Fig C) (5) Remove the pre-inserted M10 mounting screw on the upper front or rear part of top point on the XY-122 enclosure. (6) Ensure the commercially-available M10 eyebolt is secured to the upper front or rear part of top point on the enclosure to suspend it with wire as a secondary safety feature. (Fig D) CAUTION *3) CAUTION: *1) Ensure the supplied bolts are used to fix the inner yoke instead of the pre-inserted screws. *2) Make sure NOT to pinch your fingers between the inner yoke and the outer yoke when adjusting the angle. *3) The secondary safety feature must be used to prevent the speaker from falling. Eye bolts to be used as secondary safety feature are not included with the products. When you use any commercially-available eyebolts, please use the eyebolts meeting the following size and specification. M10 x 30mm, P=1.5, Safe Working Load limits: 1.47[kN] (150[kg]) and more. Please refer to "3.1 Eyebolt Strength" for further details. Ensure a wire or a chain to be used as secondary safety feature is securely suspended vertically from the ceiling or wall. If such a wire or a chain is suspended from the inclined ceiling or wall, or it is horizontally suspended, the wire or the chain would not be effective to prevent an accidental fall. An appropriate length of wire or chain should be used as second safety feature. It is generally recommended that the fall prevention wire be 150 mm longer than the main suspension wire/chain/tool. If the wire or the chain is too long, it would not be effective to prevent an accidental fall.

12 (B) (A) (C) (D) Fig A Fig A φ13 Fig B Commercially-available eyebolt Fig C Fig D

13 3.1.2 Horizontal Flying Cradle (CP-XY12HC1) When using the Horizontal Flying Cradle (CP-XY12HC1), suspension of the XY-122 enclosure horizontally from the ceiling or the wall as shown in the right figure is available. The orientation of the XY-122 enclosure can be changed at any angle. Several holes on the outer yoke of the cradle are used to change the mounting point of the mounting plate so that the distance between the XY-122 enclosure and the cradle can be adjusted. The distance between the enclosure and the cradle is set at the nearest position as the factory default. If you want to incline the XY-122 enclosure with the speaker cable connected, please select a different hole on the outer yoke to enlarge the distance. The weight of the Horizontal Flying Cradle is 4.0 kg. To the ceiling To the wall Note: The dispersion orientation when placing the XY-122 enclosure horizontally will be changed from the orientation when placing it vertically. Rotate should be in contact with the cradle. The horn inside of the enclosure to reverse the dispersion orientation to the original orientation when it is placed vertically. Also, the location and the orientation of the logo badge can be changed. (See "3.1.3 Horn rotation" and "3.1.4 Logo badge replacement") CAUTION: Horizontal Flying Cradle is not supposed to be used in the following situations, which may cause an injury or accident. The outer yoke of the cradle is not vertical to the ceiling The enclosure is not horizontal to the ceiling The outer yoke of the cradle is not horizontal to the wall Suspending Multiple enclosures

14 Part list Required tools Item Part Name Qty Service Part No. Note screwdriver A Horizontal Flying Cradle 1 - Main Yoke 1 - Mounting Plate 2 - Neoprene Washer 2 05B010 40mm x 2mm Flat Washer 2 06D014 M10 Spring Washer 2 06D015 M10 8mm hex key Lever 2 05A103 M10 B M10 socket head bolt 5 06G046 M10 x 40mm (P=1.5), 8mm hex socket head C Spring Washer 5 06D015 M10 D Flat washer 5 06D014 M10 Procedure (1) (2) (3) (4) (5) (6) Note: The yoke length can be changed by unscrewing the lever and choosing mounting holes in the both yoke ends of the Horizontal Flying Cradle. Remove the four pre-inserted mounting screws on the top and the bottom of XY-122. (Fig A) Using the supplied M10 hex socket head bolts(b), align the mounting holes in the end mounts of the yoke of the horizontal Flying Cradle(A) with the mounting the top and points on the bottom of the enclosure. Ensure that both Spring Washer(C) and Flat washer(d) are used - the flat washer(d) should be in contact with the cradle. Tighten the bolts over 15N m torque. (Fig B) CAUTION *1) Once the desired angle of the loudspeaker is set, tighten the levers on the cradle to lock the position in place. (Fig C) The holes (φ13) on the top of the horizontal Flying Cradle(A) can be used to install the speaker to the ceiling or the wall in the horizontal position. (Fig C) Remove the two mounting screws pre-inserted in the M10 holes on the rear side of XY-122 enclosure. Ensure the two commercially-available M10 eyebolts are secured to the rear points on the enclosure to suspend it with wire as a secondary safety feature. (Fig D) CAUTION *2) CAUTION: *1) Ensure the supplied bolts are used to fix the mounting plate instead of the pre-inserted screws. *2) The secondary safety feature must be used to prevent the speaker from falling. Eye bolts to be used as secondary safety feature are not included with the products. When you use any commercially-available eyebolts, please use the eyebolts meeting the following size and specification. M10 x 30mm, P=1.5, Safe Working Load limits: 1.47[kN] (150[kg]) and more. Please refer to "3.1 Eyebolt Strength" for further details. Ensure a wire or a chain to be used as secondary safety feature is securely suspended vertically from the ceiling or wall. If such a wire or a chain is suspended from the inclined ceiling or wall, or it is horizontally suspended, the wire or the chain would not be effective to prevent an accidental fall. An appropriate length of wire or chain should be used as second safety feature. It is generally recommended that the fall prevention wire be 150 mm longer than the main suspension wire/chain/tool. If the wire or the chain is too long, it would not be effective to prevent an accidental fall.

15 (A) Fig A Fig B (D) (C) Fig B (B) φ13 X 3 250mm 250mm Commercially -available eyebolt Fig C Fig D

16 3.1.3 Horn rotation HF dispersion orientation can be changed by rotating the HF waveguide 90 degrees. (Fig A) Factory default 60 After rotating the waveguide Required tools 4mm hex key Procedure (1) Using a 4 mm hex key, unscrew the four M6 countersunk bolts on the top and the bottom of the enclosure. (Fig A) (2) Gently remove the grille from the front of the enclosure. (Fig A) (3) Using a 4 mm hex key, remove the eight countersunk bolts holding the HF waveguide in place. (Fig B) (4) Lift the waveguide up and rotate it 90 degrees to change the dispersion orientation depending on the orientation of the enclosure. When the HF waveguide is rotated back to the original orientation, ensure it is rotated in the reverse direction when it was first rotated. (Fig C) (5) Reinstate the countersunk bolts and retighten. Avoid over tightening as this may crack the waveguide. (Fig D) (6) Reinstate the grille by gently placing it in place over the front of the loudspeaker. (Fig E) (7) Reinstate the four M4 countersunk bolts to secure it in place. (Fig E)

17 Fig A Fig B Fig C Fig D Fig E

18 3.1.4 Logo badge replacement The location of Logo badge attached to the grilles on XY-122 can be changed. Required tools Phillips head screwdriver 4mm hex key Procedure (1) Unscrew the four M6 countersunk bolts on the top and the bottom of XY-122. (Fig A) (2) Gently remove the grille from the front of the enclosure. (Fig A) (3) Unscrew the screw on the rear side of the Logo badge and remove the Flat washer and the Spacer. (Fig B) (4) Relocate the Log badge to the desired position on the grille. The Logo badge can be rotated 90 degrees depending on the orientation of the enclosure. (Fig C, D, E) Fig A Fig B Fig C Fig D Fig E

19 3.1.5 Variable Angle Bracket (CP-XY12AB1) When using the Variable Angle Bracket (CP-XY12AB1), suspension of the XY-122 enclosure vertically from the ceiling as shown in the right figure is available. The enclosure can be inclined forward at an angle of 43 degrees and backward 17 degrees from the vertical position. It is easier to change the inclined angle of Variable Angle Bracket than that of Vertical Flying Cradle. The weight of Variable Angle Bracket is 2.3 kg. Note: Variable Angle Bracket can be used together with Dual Enclosure Flying Plate Set. To the ceiling CAUTION: Variable Angle Bracket is not supposed to be used in the following situations, which may cause an injury or accident. Not suspending vertically Suspending from the wall Suspending Multiple enclosures Part list Required tools Item Part Name Qty Service Part No. Note Screwdriver A Variable Angle Bracket 1 - B Hook-clamp 1 - C M10 socket head bolt 2 06G052 M10 x 70mm (P=1.5), 8mm hex socket head D M10 hex head bolt 3 05C007 M10 x 40mm (P=1.5), 8mm hex key 16mm hex head E Spring washer for (D) 3 06D015 M10 F Flat washer 5 06D014 M10 G Nut 2 06E012 M10 16mm hex spanner 16mm width across flat

20 Procedure (1) Remove the two pre-inserted mounting screws on the top of XY-122. (Fig A) (2) Using the supplied M10 hex head bolts(d), align the mounting holes in the Variable angle bracket(a) with the mounting points on the top of the enclosure. Ensure that both the Spring washers(e) and Flat washers(f) are used - the Flat washer(f) should be in contact with the cradle. Tighten the bolts over 15N m torque. (Fig B) CAUTION *1) (3) Using the socket head bolt(c) and the Nut(G), attach the hook-clamp(b) to the mounting point. Moving the pickup point to the rear of the enclosure will add down-tilt, and moving to the front of the enclosure will apply up-tilt. Ensure that two Flat Washers (F) are used between the Hook-clamp(B) and M10 socket head bolt(c) as well as the nut(g) and the hook-clamp(b). (Fig C, D, E) CAUTION *2) Note: For larger down-tilt angles, position the pivot on the last hole and use the point on the rear or underside as a pull-back. (4) The hole (φ13) on the hook-clamp(b) can be used to install the speaker to the ceiling. (Fig F) (5) Remove the pre-inserted M10 mounting screw on the either right or left mounting point on the top of the XY-122 enclos (6) Ensure the commercially-available eyebolt are secured to either right or left mounting point on the top of the enclosure to suspend it with wire as a secondary safety feature. (Fig G) CAUTION *3) CAUTION: *1) Ensure the supplied bolts are used in the above (1) instead of the pre-inserted screws. *2) Ensure the lock nut (G) are fully tightened onto the socket head bolt (C). *3) The secondary safety feature must be used to prevent the speaker from falling. Eye bolts to be used as secondary safety feature are not included with the products. When you use any commercially-available eyebolts, please use the eyebolts meeting the following size and specification. M10 x 30mm, P=1.5, Safe Working Load limits: 1.47[kN] (150[kg]) and more. Please refer to "3.1 Eyebolt Strength" for further details. Ensure a wire or a chain to be used as secondary safety feature is securely suspended vertically from the ceiling or wall. If such a wire or a chain is suspended from the inclined ceiling or wall, or it is horizontally suspended, the wire or the chain would not be effective to prevent an accidental fall. An appropriate length of wire or chain should be used as second safety feature. It is generally recommended that the fall prevention wire be 150 mm longer than the main suspension wire/chain/tool. If the wire or the chain is too long, it would not be effective to prevent an accidental fall. (D) (B) (G) (F) (F) (C) (E) (F) (A) Fig A Fig B Fig C

21 The mounting point Angle [ ] Front Back Fig D Fig E Commercially -available eyebolt Fig F Fig G

22 3.1.6 Dual Enclosure Flying Plate Set (CP-XY12DF1) When using the Dual Enclosure Flying Plate Set (CP-XY12DF1), two XY-122 enclosures can be stably combined side by side and vertically or horizontally suspended from the ceiling as shown in the right figure. The angle between the 2 enclosures can be ranged from 50 degree to 95 degree. The weight of the Dual Enclosure Flying Plate Set is 12.6 kg. To the ceiling Note: Dual Enclosure Flying Plate Set can be used together with Variable Angle Bracket. To the ceiling CAUTION: Dual Enclosure Flying Plate Set is not supposed to be used in the following situations, which may cause an injury or accident. A B A B Not suspending vertically Suspending Over 2 enclosures Unsymmetry placement

23 Part list Required tools Item Part Name Qty Service Part No. Note Screwdriver A Dual Enclosure Flying Plate 2 - B M10 socket head bolt 9 06G053 M10 x 40mm (P=1.5), 8mm hex socket head C Spring washer 9 06D015 M10 D Flat washer 13 06D014 M10 E Nut 3 06E012 M10 16mm width across flat F M8 socket head bolt 3 06G046 M8 x 30mm(P=1.25), 6mm hex socket head G M8 flat washer 5 06D009 M8 H M8 nut 3 06E010 M8 13mm width across flat 8mm hex key

24 Procedure (1) Remove the eight pre-inserted mounting screws on the top and the bottom of 2 units of XY-122. (Fig A) (2) Using the supplied M10 socket head bolts(b), tentatively align the mounting holes on the Dual enclosure flying plate(a) with the mounting points of the top and the bottom of the enclosure. Ensure that both the Spring washer(c) and Flat washer(d) are used in between the Dual enclosure flying plate(a) and the M10 socket head bolt(b). Tighten the bolts over 15N m torque. (Fig B) CAUTION *1) Vertical installation (3) Remove the two mounting screws pre-inserted M10 on both edges of the top of the XY-122 enclosure. (Fig C) (4) Ensure the two commercially-available M10 eyebolts are secured to the mounting points on both edges of the top of the XY-122 enclosures to suspend it with wire as a secondary safety feature. (Fig C) CAUTION *4) (5) Note: The angle between the two enclosures can be adjusted between 50 degrees and 95 degrees when using the Dual Enclosure Flying Plate Set (Fig E). CAUTION *3) Horizontal installation (6) Once the desired angles of the two XY-122 are set, fully tighten all the M10 socket head bolts(b) on both the top and the bottom of the enclosure to lock the position in place. (Fig F) (7) (8) Once the desired angles of the two XY-122 are set, fully tighten all the M10 socket head bolts(b) on both the top and the bottom of the enclosure to lock the position in place. The three M10 holes on the top of the Dual enclosure flying plate can be used to install the speaker to the ceiling as shown in the figure. (Fig D) CAUTION *2) Eyebolts to be used as secondary safety feature cannot be mounted if the angle between the 2 enclosures is below 50 degrees. Since eyebolts should be mounted to the enclosure as secondary safety feature, the angle between the 2 enclosures should be between 50 degrees and 95 degrees in order to mount the eyebolts. If you adjust the length of the front side wires among the ones suspending the enclosure, the enclosure will be inclined downward. The safety limit of inclined angle is 28 degrees when the angle between the two enclosures is at minimum (50 degrees) and 19 degrees when the angle between them is at maximum (95 degrees). Note: The angle between the two enclosures can be adjusted between 50 degrees and 95 degrees when using the Dual Enclosure Flying Plate Set (Fig D). CAUTION *3) Remove the four mounting screws pre-inserted in the M10 holes on the side of the XY-122 enclosure. (Fig G) The XY-122 enclosure can be suspended from the ceiling when using two commercially-available M10 eyebolts as shown in the figure below. (Fig H) CAUTION *4) (9) Remove the four pre-inserted M10 mounting screws on the rear side of XY-122 enclosure. (Fig I) (10) Ensure the two commercially-available M10 eyebolts are secured to the mounting points on both edges of the top of the XY-122 enclosures to suspend it with wire as a secondary safety feature. (Fig I) CAUTION *4) CAUTION: *1) Ensure the supplied M10 socket head bolts(b) are used to fix the Dual enclosure flying plate(a) instead of the pre-inserted screws. *2) *3) *4) The two M8 holes on the rear of the Dual enclosure flying plate(a) are used for the Variable angle bracket. Make sure NOT to use them for installing the loudspeakers to the ceiling. Ensure that the 2 enclosures of XY-122 are symmetrically placed. Otherwise, the balance will be lost and the speaker could fall, causing accidents. The secondary safety feature must be used to prevent the speaker from falling. Eye bolts to be used as secondary safety feature are not included with the products. When you use any commercially-available eyebolts, please use the eyebolts meeting the following size and specification. M10 x 30mm, P=1.5, Safe Working Load limits: 1.47[kN] (150[kg]) and more. Please refer to "3.1 Eyebolt Strength" for further details. Ensure a wire or a chain to be used as secondary safety feature is securely suspended vertically from the ceiling or wall. If such a wire or a chain is suspended from the inclined ceiling or wall, or it is horizontally suspended, the wire or the chain would not be effective to prevent an accidental fall. An appropriate length of wire or chain should be used as second safety feature. It is generally recommended that the fall prevention wire be 150 mm longer than the main suspension wire/chain/tool. If the wire or the chain is too long, it would not be effective to prevent an accidental fall.

25 Vertical installation (A) (B) (C) (D) Fig A Fig B Commerciallyavailable eyebolt Fig D Fig C 50 ~ 95 Fig E

26 Horizontal installation Fig F Fig G Commerciallyavailable eyebolt Commerciallyavailable eyebolt Fig H Fig I

27 3.1.7 Combination of Dual Enclosure Flying Plate Set (CP-XY12DF1) and Variable Angle Bracket (CP-XY12AB1) When using the Variable Angle Bracket (CP-XY12AB) together with Dual Enclosure Flying Plate (CO-XY12DF1), the 2 enclosures of XY-122 stably suspended from the ceiling can be inclined forward and backward. The angle between the 2 enclosures can be ranged from 50 degree to 95 degree. To the ceiling CAUTION: The Variable Angle Bracket and the Dual Enclosure Flying Plate Set are not supposed to be used in the following situations, which may cause an injury or accident. A B A B Not suspending vertically Suspending from the wall Suspending Over 2 enclosures Unsymmetry placement Part list (CP-XY12DF1) Required tools Item Part Name Qty Service Part No. Note Screwdriver A Dual Enclosure Flying Plate 2 - B M10 socket head bolt 9 06G053 M10 x 40mm (P=1.5), 8mm hex socket head C Spring washer 9 06D015 M10 D Flat washer 13 06D014 M10 8mm hex key E Nut 3 06E012 M10 16mm width across flat F M8 socket head bolt 3 06G046 M8 x 30mm(P=1.25), 6mm hex socket head G M8 flat washer 5 06D009 M8 H M8 nut 3 06E010 M8 13mm width across flat Part list (CP-XY12AB1) Item Part Name Qty Service Part No. Note I Variable Angle Bracket 1 - J Hook-clamp 1 - K M10 socket head bolt 2 06G052 M10 x 70mm (P=1.5), 8mm hex socket head L M10 hex head bolt 3 05C007 M10 x 40mm (P=1.5), 17mm hex head M Spring washer 3 06D015 M10 N Flat washer 5 06D014 M10 O Nut 2 06E012 M10 16mm width across flat 16mm hex spanner, 13mm hex spanner

28 Procedure (1) Using the supplied M10 hex head bolts(l), M8 socket head bolts(f) and the Nuts(E, H) align the two M10 holes in the center and the two M8 holes in the rear of the Dual enclosure flying plate(a) with the mounting points of the Variable angle bracket(i). Ensure that two Flat Washers(D, G) are used between the Variable angle bracket(i) and the bolts(l, F) as well as the nuts(e, H) and the Dual enclosure flying plate(a). Tighten the bolts over 7N m torque. (Fig A) (2) Remove the eight pre-inserted mounting screws on the top and the bottom of the two XY-122 enclosures. (Fig B) (3) Using the supplied M10 socket head bolts(b), tentatively align the mounting holes on the Dual enclosure flying plate(a) with the mounting points of both the top and the bottom of the enclosure. Tighten the bolts over 15N m torque. Ensure that the Dual enclosure flying plate, where the Variable angle bracket is attached in the above (1), is attached to the top of XY-122. (Fig C) CAUTION *1) (4) Remove the two mounting screws pre-inserted M10 on both edges of the top of the XY-122 enclosure. (5) Ensure the two commercially-available eyebolts are secured to the mounting points on both edges of the top of the XY- 122 enclosures to suspend it with wire as a secondary safety feature. (Fig.3-1-D) CAUTION *4) (6) Once the desired angles of the two XY-122 are set, fully tighten all the M10 socket head bolts to lock the position in place. (Fig E) CAUTION *2) Note: The angle between the two enclosures can be adjusted between 50 degrees and 95 degrees when using the Dual Enclosure Flying Plate Set (A) Eyebolts to be used as secondary safety feature cannot be mounted if the angle between the 2 enclosures is below 50 degrees. Since eyebolts should be mounted to the enclosure as secondary safety feature, the angle between the 2 enclosures should be between 50 degrees and 95 degrees in order to mount the eyebolts. When the hook clamp is mounted in the very rear mounting point, the inclined angle of the both enclosures is 36 degrees when the angle between the two enclosures is at minimum (50 degrees) and 29 degrees when the angle between them is at maximum (95 degrees). (7) Using the supplied M10 socket head bolt(k) and Nuts(O), attach a hook-clamp to the mounting point. Moving the pickup point to the rear of the enclosure will add down-tilt, and moving to the front of the enclosure will apply up-tilt. Ensure that two Flat washers(n) are used between the Hook-clamp(J) and M10 socket head bolt(k) as well as the nut(o) and the hook-clamp(j). (Fig E) CAUTION *3) (8) The hole (Φ13) on the Hook-clamp(J) can be used to install the speaker to the ceiling. (Fig F) CAUTION: *1) Ensure the supplied M10 socket head bolts(b) are used to attach the Dual enclosure flying plate(a) instead of the pre-inserted screws. *2) Ensure that the two enclosures of XY-122 are symmetrically placed. Otherwise, the balance will be lost and the speaker could fall, causing accidents. *3) Ensure the nut(o) is fully tightened onto the M10 socket head bolt(k). *4) The secondary safety feature must be used to prevent the speaker from falling. Eye bolts to be used as secondary safety feature are not included with the products. When you use any commercially-available eyebolts, please use the eyebolts meeting the following size and specification. M10 x 30mm, P=1.5, Safe Working Load limits: 1.47[kN] (150[kg]) and more. Please refer to "3.1 Eyebolt Strength" for further details. Ensure a wire or a chain to be used as secondary safety feature is securely suspended vertically from the ceiling or wall. If such a wire or a chain is suspended from the inclined ceiling or wall, or it is horizontally suspended, the wire or the chain would not be effective to prevent an accidental fall. An appropriate length of wire or chain should be used as second safety feature. It is generally recommended that the fall prevention wire be 150 mm longer than the main suspension wire/chain/tool. If the wire or the chain is too long, it would not be effective to prevent an accidental fall.

29 (L) (F) (D) (I) (G) (A) (D) (E) (G) (H) Fig A Fig B (B) Commercially -available eyebolt (C) (D) Fig C Fig D

30 (J) (O)(N) (N)(K) Fig E Fig F

31 3.1.8 Wall Mount Bracket Four M8 holes for commercially-available wall mount brackets are provided on the rear of the XY-122. Note: Pioneer does not sell wall mount brackets. Please ensure that the commercially-available wall mount bracket is compatible with the sizes shown in Fig A Procedure (1) Remove the four mounting screws pre-inserted in the M8 holes on the rear of the XY-122 enclosure. (Fig A) (2) Using bolts included with a commercially-available wall mount bracket, align the mounting holes on the wall mount bracket with the mounting points on the XY-122. Tighten the bolts over 7N m torque. (Fig A) CAUTION *1) (3) (4) Use the bolts included with the commercially-available wall mount bracket to attach the bracket to the wall. (Fig A) Ensure the commercially-available eyebolt is secured to the rear part of the top point on the XY-122 safety feature. CAUTION *2) CAUTION: *1) Ensure the bolts included with the wall mount bracket are used instead of the pre-inserted screws. *2) The secondary safety feature must be used to prevent the speaker from falling. Eye bolts to be used as secondary safety feature are not included with the products. When you use any commercially-available eyebolts, please use the eyebolts meeting the following size and specification. M10 x 30mm, P=1.5, Safe Working Load limits: 1.47[kN] (150[kg]) and more. Please refer to "3.1 Eyebolt Strength" for further details. Ensure a wire or a chain to be used as secondary safety feature is securely suspended vertically from the ceiling or wall. If such a wire or a chain is suspended from the inclined ceiling or wall, or it is horizontally suspended, the wire or the chain would not be effective to prevent an accidental fall. An appropriate length of wire or chain should be used as second safety feature. It is generally recommended that the fall prevention wire be 150 mm longer than the main suspension wire/chain/tool. If the wire or the chain is too long, it would not be effective to prevent an accidental fall. Commercially-available eyebolt M8 x 4 127mm 70mm Fig A Commercially-available wall mount bracket

32 3.1.9 Suspension of the XY-122 enclosure using the eye bolt The XY-122 enclosure has total of 14 mounting points where commercially-available eyebolts can be mounted. Using the commercially-available eye bolts, a XY-122 enclosure or a combination of them can be vertically or horizontally suspended. If eyebolts are secured to the rear side of the XY-122 enclosure for suspension, the enclosure can be inclined downward. Note: If the recommended mounting point is used for horizontal suspension of the XY-122 enclosure, the enclosure will be inclined approximately 10 degrees. If a larger angle of incline than the above is applied, ensure that the mounting points in the rear side of the enclosure is used. Top/Bottom Rear Left/Right Mounting points Fig A 10 Fig B

33 CAUTION: When you use any commercially-available eyebolts, please use the eyebolts meeting the following size and specification: M10 x 30mm, P=1.5, Safe Working Load limits: 1.47[kN] (150[kg]) or more. The safe working load limits of an eyebolt are different depending on an inclined angle of the wire attached to the eyebolt. If the suspension angle of the wire attached to the eyebolt is inclined (not vertical) and correctly oriented in the plane of pull, be sure to read the catalogue of the eye bolt for details of the safe working load limits depending on the inclined angle. It is generally recommended that an angle of the wire attached to the eye bolt correctly oriented in the plane of pull be 45 degrees at maximum. Do not suspend the eye bolts as shown here. Be sure to meet the conditions and requirements shown in the Table A. The secondary safety feature must be used to prevent the speaker from falling. Eye bolts to be used as secondary safety feature are not included with the products. Ensure a wire or a chain to be used as secondary safety feature is securely suspended vertically from the ceiling or wall. If such a wire or a chain is suspended from the inclined ceiling or wall, or it is horizontally suspended, the wire or the chain would not be effective to prevent an accidental fall. An appropriate length of wire or chain should be used as second safety feature. It is generally recommended that the fall prevention wire be 150 mm longer than the main suspension wire/chain/tool. If the wire or the chain is too long, it would not be effective to prevent an accidental fall. Maximum Number of Enclosures Minimum Number of Suspension Lines Maximum Working Load limit per mounting point Table A Three, either vertical or horizontal Two, either vertical or horizontal 60 kg Eyebolt is not supposed to be used in the following situations, which may cause an injury or accident. 0 ~ ±45 Over 120 kg Suspending Over 3 Enclosures Suspended by 1 line of wire/chain/tool Not suspending vertically M8 holes for wall mount bracket

34 3.2 XY-81 Mounting points are provided on the enclosures of XY-81 for the suspension purpose. A cradle or a commercially-available eyebolt can be mounted to a mounting point when the enclosure is installed to a ceiling or a wall. The Safe Working Load limits: 60 kg/mounting point at maximum WARNING: Do not use a method other than the one prescribed in this manual. CAUTION: EYEBOLT STRENGTH When you use any commercially-available eyebolts, please use the eyebolts meeting the following size and specification: M8 x 15mm, P=1.25, Safe Working Load limits: 0.785[kN] (80[kg]) and more. The safe working load limits of an eyebolt are different depending on an inclined angle of the wire attached to the eyebolt. If the suspension angle of the wire attached to the eyebolt is inclined (not vertical) and correctly oriented in the plane of pull, be sure to read the catalogue of the eye bolt for details of the safe working load limits depending on the inclined angle. It is generally recommended that an angle of the wire attached to the eye bolt correctly oriented in the plane of pull be 45 degrees at maximum. Do not suspend the eye bolts as shown in here. 0 ~ ±45 PREPARING THE CABINET Pre-inserted M8 and M6 screws are mounted in the top, bottom, rear, side of the loudspeaker enclosure. These screws are painted in the cabinet color. Follow the steps below to ensure the cabinet paint is not peeled off during unscrewing. (1) Make a small slit around the pre-inserted screws using an appropriate cutting knife. (2) Carefully remove the screws using a screwdriver, and ensure the cabinet (1) (2) coating is not peeled off.

35 3.2.1 Vertical Flying Cradle (CP-XY8VC1) When using the Vertical Flying Cradle (CP-XY8VC1), suspension of the XY-81 enclosure vertically from the ceiling as shown in the right figure is available. The XY-81 enclosure can be inclined both forward and backward from the vertical position at an angle of 75 degrees. The weight of the Vertical Flying Cradle is 2.6 kg. To the ceiling CAUTION: Vertical Flying Cradle is not supposed to be used in the following situations, which may cause an injuray or accident. OVER 75 The outer yoke of the cradle is not vertical to the ceiling The enclosure is not horizontal to the ceiling Inclining over 75 degrees Suspending from the wall Suspending multiple enclosures

36 Part list Required tools Item Part Name Qty Service Part No. Note Screwdriver A Vertical Flying Cradle 1 - Outer Yoke 1 - Inner Yoke 1 - Neoprene Washer 2 05B010 40mm x 2mm Flat Washer 2 06D009 M10 Spring Washer 2 06D011 M10 5mm hex key Knob 2 05A101 M10 B M8 countersunk bolt 3 06G019 M8 x 30mm (P=1.25) 5mm hex socket head Procedure (1) Remove the two pre-inserted mounting screws from the top of XY-81. (Fig A) (2) Using the supplied two M8 countersunk bolt(b), align the mounting holes in the inner yoke of the Vertical Flying Cradle(A) with the mounting points on the top of the enclosure. Tighten the bolts over 7N m torque. (Fig B) CAUTION *1) (3) Once the desired angle of the loudspeaker is set, tighten the knobs on the cradle to lock the position in place. (Fig C) CAUTION *2) (4) The hole (φ13) on the outer yoke of the Vertical Flying Cradle(A) can be used to install the speaker to the ceiling. (Fig C) (5) Remove the pre-inserted M8 mounting screw on the top of XY-81 enclosure. (Fig D) (6) Ensure the commercially-available M8 eyebolt is secured to the front part or rear part of the top point on the enclosure to suspend it with wire as a secondary safety feature. (Fig D) CAUTION *3) CAUTION: *1) Ensure the supplied bolts are used in the above (1) instead of the pre-inserted screws. *2) Make sure not to pinch your fingers between the inner yoke and the outer yoke when adjusting the angle. *3) The secondary safety feature must be used to prevent the speaker from falling. Eye bolts to be used as secondary safety feature are not included with the products. When you use any commercially-available eyebolts, please use the eyebolts meeting the following size and specification. M8 x 15mm, P=1.25, Safe Working Load limits: 0.785[kN] (80[kg]) and more. Please refer to "3.2 Eyebolt Strength" for further details. Ensure a wire or a chain to be used as secondary safety feature is securely suspended vertically from the ceiling or wall. If such a wire or a chain is suspended from the inclined ceiling or wall, or it is horizontally suspended, the wire or the chain would not be effective to prevent an accidental fall. An appropriate length of wire or chain should be used as second safety feature. It is generally recommended that the fall prevention wire be 150 mm longer than the main suspension wire/chain/tool. If the wire or the chain is too long, it would not be effective to prevent an accidental fall.

37 (B) (A) Commercially-available eyebolt Fig A φ13 Fig B Fig C Fig D

38 3.2.2 Horizontal Flying Cradle (CP-XY8HC1) When using the Horizontal Flying Cradle (CP-X8HC1), suspension of the XY-81 enclosure horizontally from the ceiling or the wall as shown in the right figure is available. The orientation of the XY-81 enclosure can be changed at any angle. Several holes on the outer yoke of the cradle are used to change the mounting point of the mounting plate so that the distance between the XY-81 enclosure and the cradle can be adjusted. The distance between the enclosure and the cradle is set at the nearest position as the factory default. If you want to incline the XY-81 enclosure with the speaker cable connected, please select a different hole on the outer yoke to enlarge the distance. The weight of the Horizontal Flying Cradle is 2.5 kg. Note: The dispersion orientation when placing the XY-81 enclosure horizontally will be changed from the orientation when placing it vertically. Rotate the horn inside of the enclosure to reverse the dispersion orientation to the original orientation when it is placed vertically. Also, the location and the orientation of the logo badge can be changed. (See "3.2.3 Horn rotation" and "3.2.4 Logo badge replacement") To the wall To the ceiling To the wall CAUTION: Horizontal Flying Cradle is not supposed to be used in the following situations, which may cause an injuray or accident. The outer yoke of the cradle is not vertical to the ceiling The enclosure is not horizontal to the ceiling Suspending Multiple enclosures Parts list Required tools Item Parts Name Qty Service Part No. Note Screwdriver A Horizontal Flying Cradle 1 - Main Yoke 1 - Mounting Plate 2 - Neoprene Washer 2 05B010 40mm x 2mm Flat Washer 2 06D009 M10 5mm hex key Spring Washer 2 06D011 M10 Knob 2 05A101 M10 B M8 countersunk bolt 5 06G019 M8 x 30mm (P=1.25), 5mm hex socket head

39 Procedure Note: The yoke length can be changed by unscrewing the knob and choosing mounting holes in the both yoke ends of the Horizontal Flying Cradle. (1) Remove the four pre-inserted mounting screws on the top and the bottom of XY-81. (Fig A) (2) Using the supplied M8 countersunk bolts(b), align the mounting holes in the end mounts of the yoke of the horizontal Flying Cradle(A) with the mounting points on the top and the bottom of the enclosure. Tighten the bolts over 7N m torque. (Fig B) CAUTION *1) (3) Once the desired angle of the loudspeaker is set, tighten the knobs on the cradle to lock the position in place. (Fig C) (4) The holes (φ13) on the top of the horizontal Flying Cradle(A) can be used to install the speaker to the ceiling or the wall in the horizontal or vertical position. (Fig C) (5) Remove the pre-inserted M8 mounting screws on the rear point on XY-81 enclosure. (Fig D) (6) Ensure the commercially-available M8 eyebolt is secured to the rear point on the enclosure to suspend it with wire as a secondary safety feature. (Fig D) CAUTION *2) CAUTION: *1) Ensure the supplied M8 countersunk bolt(b) are used instead of the pre-inserted screws. *2) The secondary safety feature must be used to prevent the speaker from falling. Eye bolts to be used as secondary safety feature are not included with the products. When you use any commercially-available eyebolts, please use the eyebolts meeting the following size and specification. M8 x 15mm, P=1.25, Safe Working Load limits: 0.785[kN] (80[kg]) and more. Please refer to "3.2 Eyebolt Strength" for further details. Ensure a wire or a chain to be used as secondary safety feature is securely suspended vertically from the ceiling or wall. If such a wire or a chain is suspended from the inclined ceiling or wall, or it is horizontally suspended, the wire or the chain would not be effective to prevent an accidental fall. An appropriate length of wire or chain should be used as second safety feature. It is generally recommended that the fall prevention wire be 150 mm longer than the main suspension wire/chain/tool. If the wire or the chain is too long, it would not be effective to prevent an accidental fall. (A) (B) Fig A Fig B

40 φ13 x 3 180mm 180mm Fig C Fig D Commercially -available eyebolt

41 3.2.3 Horn rotation HF dispersion orientation can be changed by rotating the HF waveguide 90 degrees Factory default After rotating the waveguide Required tools 4mm hex key 3mm hex key Procedure (1) (2) Gently remove the grille from the front of the enclosure. (Fig A) (3) Unsing a 4 mm hex key, remove the four M5 socket head bolts holding the HF waveguide in place. (Fig B) (4) Lift the waveguide up and rotate it 90 degrees to change the dispersion orientation depending on the orientation of the enclosure. When the HF waveguide is rotated back to the original orientation, ensure it is rotated in the reverse direction when it was first rotated. (Fig C) (5) Using a 3 mm hex key, unscrew the four M4 machine screws on the top and the bottom of the XY-81 enclosure. (Fig A) Reinstate the M5 socket head bolts and retighten. Avoid over thightening as this may crack the waveguide. (Fig D) (6) Reinstate the grille by gently placing it in place over the front of the loudspeaker. (Fig E) (7) Reinstate the four M4 machine screws to secure it in place. (Fig E) Fig A Fig B

42 Fig C Fig D Fig E

43 3.2.4 Logo badge replacement The location of Logo badge attached to the grille on XY-81 can be changed. Required tools Phillips head screwdriver 3mm hex key Procedure (1) Unscrew the four M4 machine screws on the top and the bottom of XY-81. (Fig A) (2) Gently remove the grille from the front of the enclosure. (Fig A) (3) Unscrew the screw on the rear side of the Logo badge and remove the Flat washer and the Spacer. (Fig B) (4) Relocate the Log badge to the desired position on the grille. The Logo badge can be rotated 90 degrees depending on the the orientation of the enclosure. Please ensure that the Logo badge does not touch the HF waveguide, Driver unit and the screws during the above procedures. (Fig C, D, E) CAUTION *1) CAUTION: *1) The Logo badge can be attached to only the limited locations on the grille. Please see the Fig F, G. If the Logo badge is attached to other locations than the specified ones, the speaker could be damaged. Ensure the Logo badge is attached to the specified area.

44 Fig A Fig B Fig C Fig D Fig E

45 Top DO NOT ATTACH THE LOGO BADGE DO NOT ATTACH THE LOGO BADGE DO NOT ATTACH THE LOGO BADGE DO NOT ATTACH THE LOGO BADGE Factory default 5 holes DO NOT ATTACH THE LOGO BADGE A Plate support the grill 2 holes Bottom GRAY COLOR AREA DO NOT ATTACH THE LOGO BADGE NO LOGO BADGE STICKING OUT Fig F For vertical installation 8 holes 8 holes Bottom A plate support the grille DO NOT ATTACH THE LOGO BADGE DO NOT ATTACH THE LOGO BADGE Top DO NOT ATTACH THE LOGO BADGE A plate support the grille DO NOT ATTACH THE LOGO BADGE 5 9 holes holes DO NOT ATTACH THE LOGO BADGE GRAY COLOR AREA DO NOT ATTACH THE LOGO BADGE NO LOGO BADGE STICKING OUT Fig G For horizontal installation

46 3.2.5 Wall Mount Bracket Four M6 holes for commercially-available wall mount brackets are provided on the rear of the XY-81. Note: Pioneer does not sell wall mount brackets. Please ensure that the commercially-available wall mount bracket is compatible with the sizes shown in Fig A Procedure (1) Remove the four mounting screws pre-inserted in the M6 holes on the rear of XY-81 enclosure. (Fig A) (2) Using bolts included with a wall mount bracket, align the mounting holes on the wall mount bracket with the mounting points on the XY-81. (Fig A) Tighten the bolts over 3.5N m torque. CAUTION *1) (3) (4) Use the bolts included with the commercially-available wall mount bracket to attach the bracket to the wall. (Fig A) Ensure the commercially-available M8 eyebolt is secured to the rear part of the top point on the XY-81 enclosure to suspend it with wire as a secondary safety feature. (Fig A) CAUTION *2) CAUTION: *1) Ensure the bolts included with the wall mount bracket are used instead of the pre-inserted screws. *2) The secondary safety feature must be used to prevent the speaker from falling. Eye bolts to be used as secondary safety feature are not included with the products. When you use any commercially-available eyebolts, please use the eyebolts meeting the following size and specification. M8 x 15mm, P=1.25, Safe Working Load limits: 0.785[kN] (80[kg]) and more. Please refer to "3.2 Eyebolt Strength" for further details. Ensure a wire or a chain to be used as secondary safety feature is securely suspended vertically from the ceiling or wall. If such a wire or a chain is suspended from the inclined ceiling or wall, or it is horizontally suspended, the wire or the chain would not be effective to prevent an accidental fall. An appropriate length of wire or chain should be used as second safety feature. It is generally recommended that the fall prevention wire be 150 mm longer than the main suspension wire/chain/tool. If the wire or the chain is too long, it would not be effective to prevent an accidental fall. Commercially-available eyebolt M6 x 4 108mm 50.8 Commercially-available wall mount bracket Fig A

47 3.2.6 Suspension of the XY-81 enclosure using the eye bolt The XY-81 enclosure has total of 9 mounting points where commercially-available eyebolts can be mounted. Using the commercially-available eye bolts, a XY-81 enclosure or a combination of them can be vertically suspended. If eyebolts are secured to the rear side of the XY-81 enclosure for suspension, the enclosure can be inclined downward. Rear Top/Bottom Mounting point Fig A Fig B

48 CAUTION: When you use any commercially-available eyebolts, please use the eyebolts meeting the following size and specification: M8 x 15mm, P=1.25, Safe Working Load limits: 0.785[kN] (80[kg]) and more. The safe working load limits of an eyebolt are different depending on an inclined angle of the wire attached to the eyebolt. If the suspension angle of the wire attached to the eyebolt is inclined (not vertical) and correctly oriented in the plane of pull, be sure to read the catalogue of the eye bolt for details of the safe working load limits depending on the inclined angle. It is generally recommended that an angle of the wire attached to the eye bolt correctly oriented in the plane of pull be 45 degrees at maximum. Do not suspend the eye bolts as shown here. Multiple XY-81 enclosures in horizontal orientation should not be combined for suspension. Be sure to meet the conditions and requirements shown in the Table A. The secondary safety feature must be used to prevent the speaker from falling. Eye bolts to be used as secondary safety feature are not included with the products. Ensure a wire or a chain to be used as secondary safety feature is securely suspended vertically from the ceiling or wall. If such a wire or a chain is suspended from the inclined ceiling or wall, or it is horizontally suspended, the wire or the chain would not be effective to prevent an accidental fall. An appropriate length of wire or chain should be used as second safety feature. It is generally recommended that the fall prevention wire be 150 mm longer than the main suspension wire/chain/tool. If the wire or the chain is too long, it would not be effective to prevent an accidental fall. Maximum Number of Enclosures Minimum Number of Suspension Lines Maximum Working Load limit per mounting point Table A Three Two 60 kg 0 ~ ±45 Eyebolt is not supposed to be used in the following situations, which may cause an injury or accident. Over 120 kg Suspending holrzontally Suspending Over 3 Enclosures Suspended by 1 line of wire/chain/tool Not suspending vertically M6 holes for wall mount bracket

49 3.3 XY-118S WARNING: Do not use a method other than the one prescribed in this manual. CAUTION: Preparing the cabinet Pre-inserted M8 screws are mounted in the rear side of the loudspeaker enclosure. These screws are painted in the cabinet color. To remove the screws, proceed as follows: Follow the steps below to ensure the cabinet paint is not peeled off during unscrewing. (1) Make a small slit around the pre-inserted screws using an appropriate cutting knife. (2) Carefully remove the screws using a screwdriver, and ensure the cabinet coating is not peeled off. (1) (2) Caster (CP-XYCS1) Part list Required tools Item Part Name Qty Service Part No. Note Screwdriver A Caster 4 - B M8 hex head bolt 17 06C005 M8 x 30mm (P=1.25) 13mm hex head C Spring washer 17 06D011 M8 D Flat Washer 17 06D009 M8 13mm hex spanner Procedure (1) Unscrew the sixteen pre-inserted mounting screws on the rear of XY-118S. (Fig A) (2) Using the four supplied M8 Hex head bolts(b), align the mounting points on the rear of the enclosure and the four holes on each Caster (A). Ensure that both Spring washer(c) and Flat washer(d) are used - the Flat washer(c) should be in contact with the Caster(A). Tighten the bolts over 7N m torque. (Fig B) CAUTION *1) (3) Turn the XY-118S enclosure with its grille up to roll on the casters. (Fig C) CAUTION: *1) Ensure the supplied M8 hex head bolts(b) are used in the above (1) instead of the pre-inserted screws. (B) (D) (C) (A) Fig A Fig B Fig C

50 3.4 XY-215S WARNING: Do not use a method other than the one prescribed in this manual. CAUTION: Preparing the cabinet Pre-inserted M8 screws are mounted in the rear side of the loudspeaker enclosure. These screws are painted in the cabinet color. To remove the screws, proceed as follows: Follow the steps below to ensure the cabinet paint is not peeled off during unscrewing. 1) (1) Make a small slit around the pre-inserted screws using an appropriate 2) cutting knife. (2) Carefully remove the screws using a screwdriver, and ensure the cabinet coating is not peeled off Caster (CP-XYCS1) Part List Required tools Item Parts Name Qty Service Part No. Note Screwdriver A Caster 4 - B M8 hex head bolt 17 06C005 M8 x 30mm (P=1.25) 13mm hex head C Spring washer 17 06D011 M8 13mm hex spanner D Flat Washer 17 06D009 M8 Procedure (1) Unscrew the sixteen pre-inserted mounting screws on the rear of XY-215S. (Fig A) (2) Using the four supplied M8 Hex head bolts(b), align the mounting points on the rear of the enclosure and the four holes of each Caster(A). Ensure that both the Spring washers(c) and the Flat washers(d) are used - the Flat washer(c) should be in contact with the Caster(A). Tighten the bolts over 7N m torque. (Fig B) COUTION *1) (3) Turn the XY-215S enclosure with its grille up to roll on the casters. (Fig C) CAUTION: *1) Ensure the supplied M8 hex head bolts(b) are used instead of the pre-inserted screws. (B) (D) (C) (A) Fig A Fig B Fig C

51 4 System Configuration 4.1 Connections Power Amplifier Recommendations Speaker model Impedance RMS Power Handling Program XY-122 8Ω 400W 800W XY-81 8Ω 350W 700W XY-118S 8Ω 1000W 2000W XY-215S 4Ω 800W 1600W Recommended K3DSP K2DSP K3DSP K3DSP Amplifier Minimum M30DHDSP M20DHDSP K2DSP Spesification of Power Amplifier Amplifier K-Series M-Series model K6DSP K3DSP K2DSP M30DHDSP M20DHDSP Impedance 2Ω 4Ω 8Ω 2Ω 4Ω 8Ω 2Ω 4Ω 8Ω 4Ω 8Ω 4Ω 8Ω Rated Power 3600W x 2ch 2500W x 2ch 1300W x 2ch 2800W x 2ch 2600W x 2ch 1400W x 2ch 2400W x 2ch 1950W x 2ch 1000W x 2ch 1500W x 2ch 900W x 2ch 1200W x 2ch 600W x 2ch

52 Loudspeaker connections WARNING: Ensure that cables compatible with both the specifications of the Power Amplifier and Speaker are used. Using wrong pinouts may cause damage to the speakers or occur accidents. The XY Series are supplied as standard with Neutrik SpeakON NL4 connectors, wired pin 1+/1. It is recommended that the resistance of your cable be less than one tenth of the nominal system impedance. Given below are the recommended maximum cable lengths for different cross-sections and impedances. Conductor Cross Sectional Area 1.0mm 2 1.5mm 2 2.0mm 2 2.5mm 2 4.0mm 2 6.0mm 2 Maximum Recommended Cable Length 4 Ω 8 Ω 16 Ω 11m 17m 22m 29m 44m 66m 22m 34m 44m 58m 88m 132m 44m 68m 88m 116m 176m 264m Pins 2+/2 on the Neutrik SpeakON connectors are wired together to allow link-through with 4-core cables. XY-122/81 XY-118S XY-215S

53 CAUTION K-Series and M-Series have different pinouts for the Neutrik SpeakON connectors(nl4) for Power Amplifier. K-Series M-Series inverting inverting Cable specification An example of the cable connecting XY Series products and amplifiers of K-Series or M-Series is shown below. SpeaKON TM (NL2 or NL4) Speaker Cable(2 core) +1-1 SpeaKON TM (NL2 or NL4)

54 4.2 System setting Preset Please see the [Armonia User Guide] of Powersoft for details of how to set and use the Preset and the Amplifier. URL: Please see the Pioneer website for the details of Presets and the specifications of the setting values. URL: NOTES: The presets are used for the speakers installed in recommended methods. Check the sound quality and readjust the DSP, as needed, depending on the location where a loudspeaker is installed. The combination of a Fullrange speaker and a Subwoofer presets are used for the polemount installation. If other installation methods are used, change the settings of Delay and EQ, etc. The specifications of presets are subject to change without notice. Connection chart The details of the Fig 4-2-A to Fig 4-2-H are described in the figure below. amplifier's output channel No. Speaker cable XY-122 Ch 1 K3DSP Ch 2 XY-122 XY-118S Ch 1 K3DSP Ch 2 XY-118S Speaker connect to the channel 1 Speaker connect to the channel 2 XY-122 (Stereo) XY-122 Ch 1 K3DSP Ch 2 XY-122 Fig.4-2-A Preset name KDSP_XY-122_V1.0 Description Full range output to drive XY-122 from both channels 1 & 2 of the amplifier Recommended Amp Model K3DSP Connected Speaker CH1 CH2 XY-122 XY-122

55 XY-122(Stereo) with XY-118S(MonoMix) XY-122 Ch 1 K3DSP Ch 2 XY-122 Fig.4-2-B XY-118S Ch 1 K3DSP Ch 2 XY-118S Preset name KDSP_XY-122_for_XY-118S_V1.0 Description Mid/High frequency output to drive XY-122 from both channels 1 & 2 of the amplifier combine with XY-118S Recommended Amp Model K3DSP Connected Speaker CH1 CH2 XY-122 XY-122 KDSP_XY-118S_for_XY-122_V1.0 Mono mixed Subwoofer output to drive XY-118S from both channels 1 & 2 of the amplifier combine with XY-122 K3DSP CH1 CH2 XY-118S XY-118S XY-122(Stereo) with XY-215S(MonoMix) XY-122 Ch 1 K3DSP Ch 2 XY-122 Fig.4-2-C XY-215S Ch 1 K3DSP Ch 2 XY-215S Preset name KDSP_XY-122_for_XY-215S_V1.0 Description Mid/High frequency output to drive XY-122 from both channels 1 & 2 of the amplifier combine with XY-215S Recommended Amp Model K3DSP Connected Speaker CH1 CH2 XY-122 XY-122 KDSP_XY-215S_for_XY-122_V1.0 Mono mixed Subwoofer output to drive XY-215S from both channels 1 & 2 of the amplifier combine with XY-122 K3DSP CH1 CH2 XY-215S XY-215S

56 XY-81 (Stereo) XY-81 Ch 1 K2DSP Ch 2 XY-81 Fig.4-2-D Preset name KDSP_XY-81_V1.0 Description Full range output to drive XY-81 from both channels 1 & 2 of the amplifier Recommended Amp Model K2DSP Connected Speaker CH1 CH2 XY-81 XY-81 XY-81(Stereo) with XY-118S(MonoMix) XY-81 Ch 1 K2DSP Ch 2 XY-81 Fig.4-2-E XY-118S Ch 1 K3DSP Ch 2 XY-118S Preset name KDSP_XY-81_for_XY-118S_V1.0 Description Mid/High frequency output to drive XY-81 from both channels 1 & 2 of the amplifier combine with XY-118S Recommended Amp Model K2DSP Connected Speaker CH1 CH2 XY-81 XY-81 KDSP_XY-118S_for_XY-81_V1.0 Mono mixed Subwoofer output to drive XY-118S from both channels 1 & 2 of the amplifier combine with XY-81 K3DSP CH1 CH2 XY-118S XY-118S XY-81(Stereo) with XY-215S(MonoMix) XY-81 Ch 1 K2DSP Ch 2 XY-81 Fig.4-2-F XY-215S Ch 1 K3DSP Ch 2 XY-215S Preset name KDSP_XY-81_for_XY-215S_V1.0 Description Mid/High frequency output to drive XY-81 from both channels 1 & 2 of the amplifier combine with XY-215S Recommended Amp Model K2DSP Connected Speaker CH1 CH2 XY-81 XY-81 KDSP_XY-215S_for_XY-81_V1.0 Mono mixed Subwoofer output to drive XY-215S from both channels 1 & 2 of the amplifier combine with XY-81 K3DSP CH1 CH2 XY-215S XY-215S

57 XY-118S(MonoMix) XY-118S Ch 1 K3DSP Ch 2 XY-118S Fig.4-2-G Preset name KDSP_XY-118S_V1.0 Description Mono mixed Subwoofer output to drive XY-118S from both channels 1 & 2 of the amplifier Recommended Amp Model K3DSP Connected Speaker CH1 CH2 XY-118S XY-118S *XY-118S setting combine with other full range speakers except XY-122 and XY-81 XY-215S(MonoMix) XY-215S Ch 1 K3DSP Ch 2 XY-215S Fig.4-2-H Preset name KDSP_XY-215S_V1.0 Description Mono mixed Subwoofer output to drive XY-215S from both channels 1 & 2 of the amplifier Recommended Amp Model K3DSP Connected Speaker CH1 CH2 XY-215S XY-215S *XY-215S setting combine with other full range speakers except XY-122 and XY-81 Ground stacking CAUTION Ensure that the floor or stage surface can withstand the weight of the system. Do not carry out the stack with more than of specifications shown below. Use ratchet straps to secure loudspeakers together. Please also remember that vibrations from subwoofer systems can shake other loudspeakers out of place, which may present a toppling hazard. The use of ratchet straps and non-slip material is recommended to prevent this. XY-122 XY-81 XY-118S XY-215S Maximum loadable mass No Stacking No Stacking 80kg 100kg Maximum stacking capacity No Stacking No Stacking 1pc of XY-118S and 1pc XY-122(or XY-81) 1pc of XY-215S and 1pc XY-122(or XY-81)

58 5 Drive unit replacement WARNING: Do not attempt to use this driver with components other than the specified speaker. Ensure that the loudspeaker is placed on a stable place like on a floor. Do not replace the drivers when it is stacked on other loudspeakers or it is hung from the ceiling. Certain technical skills and experiences are required to install the driver to the loudspeaker. Please have the driver installed by qualified professionals. Be sure to use and tighten the pre-inserted bolts to the driver installed to the loudspeaker when you install this driver to the loudspeaker enclosure. After installation, you must confirm that the bolts and screws used for the enclosures and the grilles of this product are tightened enough. Periodical inspections are also required to make sure they are still tightened enough. CAUTION: Inappropriate installation could affect the sound quality. Ensure the LF driver is installed in accordance with the Installation Manual. Otherwise, your fingers might be caught and get injured during the installation process. Do not store speakers at temperatures outside of the rated temperature range as doing so may cause the speaker to drop in performance or become damaged. Storage temperature range: 20 C to +55 C ( 4 F to +131 F) Do not use the product in locations subject to extreme fluctuations in temperature. Drastic fluctuation of the temperature and long storage in the cold temperature might cause small cracks in the magnet of the drive unit. The performance, reliability and safety for use of this product may not be affected even if the above issue occurs. 5.1 XY-122 Drive unit replacement Part list Required tools Item Part Name Qty Service Part No. Note 4mm hex key HF drive unit 1 PT-XY122CD1 Include the following items. 5mm hex key M6 Stud bolt 4 - Nut 4 - M6 HF Flat washer 4 - M6 Spring washer 4 - M6 M6 x 40mm (P=1.0), 10mm spanner M6 countersunk bolt 8 06G036 4mm hex socket head for HF waveguide LF drive unit 1 PT-XY122LF1 LF M6 socket head bolt 8 06G003 M6 x 40mm (P=1.0), 5mm hex socket head Spring washer 8 06D0075 M6 Grille 1 04X902 M6 x 30mm (P=1.0), Other M6 countersunk bolt 4 06G020 4mm hex socket head, for grille

59 Procedure Remove the four countersunk bolts from the grille. M6 x 30mm countersunk bolt 4pcs Replacement of HF drive unit Remove eight countersunk bolts from the HF waveguide. M6 x 40mm countersunk bolt 8pcs Remove the cables from the HF drive unit.

60 Remove the four nuts from the HF drive unit with a 10mm Spanner. Replace the HF drive unit with a new one and tighten the four nuts with the Spanner. Connect the cables to the two terminals. Red Terminal (+) : White cable Black Terminal (-) : Yellow cable Black terminal Red terminal Tighten eight countersunk bolts of the HF waveguide. Make sure to place the HF waveguide in the same orientation as before replacing the drive unit. M6 x 40mm countersunk bolt 8pcs

61 Replacement of LF drive unit CAUTION: Before replacing the LF drive unit, remove the HF waveguide from the enclosure. (See "5.1 Replacement of HF drive unit") Remove the eight socket head bolts from the LF drive unit. M6 x 40mm socket head bolt 8pcs Spring washer 8pcs Remove the cables from the LF drive unit, and replace the LF drive unit with a new one. Connect the cables to the two terminals. Red Terminal (+) : Brown cable Black Terminal (-) : Blue cable Terminals Black terminal Red terminal

62 Tighten the eight socket head bolts on the LF drive unit. Ensure that the terminals of the drive unit are placed as shown below. Location of terminals M6 x 40mm socket head bolt 8pcs Spring washer 8pcs Tighten the four countersunk bolts to ensure a solid fit to the grille. M6 x 30mm countersunk bolt 4pcs Additional information For the connection information, please refer to following circuit diagram.

63 5.2 XY-81 Drive unit replacement Part list Required tools Item Part Name Qty Service Part No. Note 3mm hex key HF drive unit 1 PT-XY81CD1 4mm hex key M6 x 20mm (P=1.0) 5mm hex key M6 socket head bolt 2 06G023 5mm hex socket head for drive unit HF M5 x 30mm (P=0.8) M5 socket head bolt 4 06G001 4mm hex socket head for HF waveguide Flat washer 4 06D003 M5 for waveguide Elastomeric adhesive Spring washer 4 06D005 M5 for waveguide LF drive unit 1 PT-XY81LF1 M5 x 30mm (P=0.8) M5 socket head bolt 8 06G001 LF 4mm hex socket head Flat washer 8 06D003 M5 Spring washer 8 06D005 M5 Grille 1 04X901 Other M4 socket head bolt 4 06G016 Procedure Remove the four socket head bolts from the grille. M4 x 20mm (P=0.7) 3mm hex socket head, for grille M4 x 20mm socket head bolt 4pcs Replacement of HF drive unit Remove the four socket head bolts from the HF waveguide. M5 x 30mm socket head bolt 4pcs, Spring washer 4pcs, Flat washer 4pcs

64 Remove the cables from the HF drive unit. Remove the two packing from the inside of the horn. Insert an hex key into the two slits appearing after the packing was removed and remove the two socket head bolts from the HF drive unit. Replace the HF drive unit to a new one and insert an hex key to tighten the two socket head bolts on the HF drive unit with an hex key. Reinstate the two packings by placing them back in the two slits. Note: Ensure that the packings are firmly attached to the slits using elastomeric adhesive, otherwise sound quality may be deteriorated.

65 Connect the cables to the two terminals. Red Terminal (+) : White cable Black Terminal (-) : Yellow cable Black terminal Red terminal Tighten the four socket head bolts on the HF waveguide. Make sure to place the HF waveguide in the same orientation as before replacing the drive unit. M5 x 30mm socket head bolt 4pcs, Spring washer 4pcs, Flat washer 4pcs Replacement of LF drive unit Remove the eight socket head bolts from the LF drive unit. M5 x 30mm socket head bolt 8pcs, Spring washer 8pcs, Flat washer 8pcs

66 Remove the two cables from the LF drive unit, and replace the LF drive unit with a new one. Connect the cables to the two terminals. Red Terminal (+) : Brown cable Black Terminal (-) : Blue cable Black terminal Red terminal Terminals Tighten the eight socket head bolts onto the LF drive unit. Ensure that the terminals of the LF drive unit are placed as shown below. Location of terminals M5 x 30mm socket head bolt 8pcs, Spring washer 8pcs, Flat washer 8pcs Tighten the four machine bolts to ensure a solid fit to the grille. M4 x 20mm socket head bolt 4pcs

67 Additional information For the connection information, please refer to following circuit diagram.

68 5.3 XY-118S Drive unit replacement Part list Required tools Item Part Name Qty Service Part No. Note Phillips head screwdriver Drive unit 1 PT-XY118SL1 LF M6 socket head bolt 8 06G003 M6 x 40mm (P=1.0), 5mm hex socket Spring washer 8 06D0075 M6 Grille 1 04X904 5mm hex key Other Screw 14 06F002 for grille Procedure Remove the fourteen screws from the grille. Screw 14pcs Remove the eight socket head bolts from the drive unit. M6 x 40mm socket head bolt 8pcs, Spring washer 8pcs

69 Remove the two cables and replace the drive unit with a new one. Connect the cables to two terminals. Red Terminal (+) : Red cable Black Terminal (-) : Black cable Black Terminal Red Terminal Terminal Tighten the eight socket head bolts onto the LF drive unit. Ensure that the terminals of the LF drive unit are placed as shown below. Location of M6 x 40mm socket head bolt 8pcs, Spring washer 8pcs Tighten the fourteen screws to ensure a solid fit to the grille. Screw 14pcs

70 Additional information For the connection information, please refer to following circuit diagram.

71 5.4 XY-215S Drive unit replacement Part list Required tools Item Part Name Qty Service Part No. Note Phillips head screwdriver Drive unit 2 PT-XY215SL1 LF M6 socket head bolt 16 06G003 M6 x 40mm (P=1.0) 5mm hex socket head Spring washer 16 06D0075 M6 Grille 1 04X903 5mm hex key Other Screw 10 06F002 for grille Procedure Remove the ten screws from the grille. Screw 10pcs Turn the speaker enclosure 90 degrees so that the drive unit to be replaced will face upward. Drive unit that you want to replace.

72 Remove the eight socket head bolts from the drive unit. M6 x 40mm socket head bolt 8pcs, Spring washer 8pcs Remove the two cables and replace the drive unit with a new one. Connect the cables to the two terminals. Red Terminal (+) : Red cable Black Terminal (-) : Black cable Black terminal Red terminal Terminals Tighten the eight socket head bolts onto the drive unit. Ensure that the terminals of the drive unit are placed as shown below. M6 x 40mm socket head bolt 8pcs, Spring washer 8pcs Left drive unit Right drive unit Location of terminals

73 Location of terminals (Left drive unit) Location of terminals (Right drive unit) Tighten the ten screws to ensure a solid fit to the grille. Screw 10pcs Additional information For the connection information, please refer to following circuit diagram.