MPS7100-M Non-Validatable Series Continuous Band Heat Sealer

Transcription

1 MPS700-M Non-Validatable Series Continuous and Heat Sealer Product Documentation Model Number: Serial Number: PLEXPCK CORP. 60 irchmount Rd. Unit, Toronto, Ontario. MP 8 Tel: , Toll Free: , Fax: info@plexpack.com Website:

2 MPS700-M CONTENTS Safety Information iii Operator Manual iv Maintenance Manual xi Spare Parts List xiii ppendix MPS700-M Electrical Schematic ppendix MPS7000-M Seal Section Pin Out ppendix C MPS700-M 0V ssemblies ppendix D MPS700-M 0V ssemblies ORIGINL Page ii

3 Plexpack Corporation 60 ircmount Road, Unit Toronto, Ontario, MP 8, Canada Tel: Fax: EC Declaration of Conformity In accordance with Directive 00/08/EC This is to declare that the Equipment: Emplex MPS Sealer Model Series: MPS 7xxx-M (x will be any number, 0-9) is in conformity with the provisions of the Directive 00/08/EC for electromagnetic emissions compatibility. Referenced normative documents: EN :007 EN :005 EN 550:007 Technical File Ref No.: Electromagnetic Compatibility (EMC). Part 6-: Generic standards - Emissions standard for industrial environments. Electromagnetic Compatibility (EMC). Part 6-: Generic standards - Immunity standard for industrial environments. Group Class Industrial, scientific and medical radio frequency equipment Electromagnetic disturbance characteristics Limits and methods of measurement. PE Toronto, ugust 0

4 EC Declaration of Conformity In accordance with Directive 98/7/EC and/or 006//EC Plexpack Corporation 60 ircmount Road, Unit Toronto, Ontario, MP 8, Canada Tel: Fax: This is to declare that the Equipment: Emplex MPS Sealer Model Series: MPS 7xxx-M (x will be any number, 0-9) is in conformity with the provisions of the Directive 98/7/EC and/or 006//EC for machinery safety. Referenced normative documents: EN ISO 00-:00 asic concepts, general principles for design. EN ISO 00-:00 asic concepts, general principles for design - Part : Technical principles - / EN 600-:006 Electrical equipment of machines. General requirements. EN ISO 857:008 Safety distances to prevent hazard zones being reached by upper and lower limbs. EN 9:99+:008 Minimum gaps to avoid crushing of parts of the human body. EN 95:997 +:009 General requirements for the design and construction of fixed and movable guards. EN 07:995+:008 Prevention of unexpected start-up EN ISO 850:007 Emergency stop Principles for design. EN 6059:99 Specification for degrees of protection provided by Enclosures (IP Code). EN ISO -:007 Risk ssessment Part : Principles S EN 6-:006+:009 Ergonomic design principles. Part : Terminology and general principles Technical File Ref No.: PE Toronto, ugust 0

5 Declaration of Noise Emission The Plexpack Corp. Model EMPLEX 7xxx-M ag Sealer, where x may be any number 0-9, noise emission levels per ISO EN 0 are as follows: Work place noise level Idle/mbient Work place noise level (Work Cycle) mbient Correction Factor K calculated according to ISO EN 0 ppendix. 57. d () 6.5 d () d () Measurements were made at a height of.5 m and m from the Operator Position. The difference between the extraneous noise level and the sound intensity level at each measuring point is. d () The figures quoted are emission levels and are not necessarily safe working levels. While there is a correlation between the emission and exposure levels this cannot be used reliably to determine whether or not further precautions are required. Factors that influence the actual level of exposure of the workforce include characteristics of the work room, the other sources of noise, etc. such as the number of machines and other adjacent processes. lso, the permissible level of exposure can vary from country to country. This information, however, will enable the user of the machine to make a better evaluation of the hazard and risk. Plexpack Corp. 60 irchmount Rd, Unit # Toronto, ON MP 8 Canada

6 MPS700-M ISO SFETY SYMOLS DEFINED Caution - General Do not operate machine until instruction manual has been read. e sure machine is connected to building electrical safety ground. e sure to disconnect the power before performing machine maintenance Do not operate machine with guards removed Do not operate machine in a manner for which it was not intended. Do not touch heated surfaces. Caution - Heavy The machine requires a minimum of two people to move or lift. There is a risk of personal injury if attempted to lift or move the machine alone. Caution Pinch Hazard e extremely careful when inserting bags into the in-feed rail. The belt drive can grab loose clothing and/or bodily parts resulting in injury. Caution Electrical High voltages present inside the control box enclosure. To reduce the risk of fire or electrical shock, do not attempt to open the enclosure. Refer servicing to qualified service personnel only. Caution Moving Parts Moving parts contained behind guards. Do not touch moving parts. Severe pinching and/or dismemberment may occur. ORIGINL Page vi

7 MPS700-M Caution Stability Hazard This stand is not meant to be mounted in anyway other than specified. The stand is designed to support the equipment in the way shown within the manual. Modifications or use other than specified may result in equipment damage and personal injury. Caution Slip Hazard If a spill or explosion occurs from a product it must be cleaned before the operator continues using the machine. Danger Hot Surfaces Hot surfaces are present behind guards. Temperatures can exceed 50 C during normal operation, do not touch. Severe burns will result. Danger Rotating lade Rotating blade is located under this cover. Do not attempt to expose this blade while the machine is powered. Prohibited Do not attempt to open, touch, or proceed before referring to the manual. Prohibited Do not expose internal components to liquids of any kind. Do not place liquids on top of control box. These actions will result in damage to the equipment and may result in personal injury. ORIGINL Page vii

8 MPS700-M Prohibited Do not use non approved lubricants on the machine as it can result in damage to the machine and void the warranty. Prohibited Do not attempt to stand or lean on the stand in anyway. Equipment damage and personal injury may occur. Prohibited Surfaces near this label can reach temperatures sufficient to burn skin when machine is in operation or cooling down. Do not touch, personal injury may occur. Mandatory Supporting documentation must be read before operating or maintaining the machine. Mandatory The machine requires a minimum of two people to move or lift. Mandatory The machine must be unplugged before proceeding. Mandatory The machine must be locked out before proceeding. ORIGINL Page viii

9 MPS700-M ISO SFETY SYMOLS LOCTION ORIGINL Page ix

10 MPS700-M OPERTION MNUL MPS700-M OPERTION MNUL ORIGINL Page x

11 MPS700-M OPERTION MNUL CONTENTS Precaution Machine Name Plate uthorized Representative Fuse Chart.0 Introduction. General Description. Specifications. Conformity. Machine Parts Diagram.5 Control ox Features.6 Stand Features.7 Dimensional Diagram.0 Unpacking & ssembly. Uncrating the MPS700-M Series. ssembling the MPS700-M Series. Unpacking the MPS70-M. ssembling the MPS70-M Product Shelf.0 Operation. Getting Started. djusting the Head Orientation. djusting the Head Height. Setting the Seal Temperature.5 Setting the Seal Speed.7 djusting Seal and Cooling ar Pressure.7 Proper ag Feeding.8 ag Support Capability.0 Relevant Misuse. Misplaced Liquids. Use of Non-pproved Lubricants. Standing on the Machine. Sealing Over Filled ags 5.0 Cleaning the Machine 5. Surface Cleaning 5. Internal Cleaning 5. Micro iological Materials 6.0 Recycling of Machine 7.0 Maintenance ORIGINL Page xi

12 MPS700-M OPERTION MNUL CUTION: To ensure the safe operation of this machine and the safety of the operator this manual must be read and understood before proceeding. This document has been produced by: Plexpack Corporation 60 irchmount Road, Unit. Toronto, Ontario MP 8 Canada The directives in this document are in accordance with the design and construction of the unit at the time it was released by the Plexpack production facility. ORIGINL INSTRUCTIONS Page

13 MPS700-M OPERTION MNUL MCHINE NMEPLTE The nameplate shown below is attached to the back of the control box and contains the information needed when contacting Plexpack technical support. UTHORIZED EU REPRESENTTIVE The plate shown below is attached on the back of the control box and contains information regarding the location of the authorized representative who holds a copy of the technical file required for CE conformity. FUSE CHRT The fuse chart is located within the control box and states the required information required to attain and replace blown fuses within the machine. Caution Replace Fuses With Same Type and Rating Fuse No. Voltage mperage SC I/R Type Size F F F ORIGINL INSTRUCTIONS Page

14 MPS700-M OPERTION MNUL.0 INTRODUCTION. GENERL DESCRIPTION The MPS700-M series machines are non-validatable continuous band sealers for the sealing of any heat sealable bag or pouch. The MPS Series utilizes variable speed and pressure, constant cooling and digital heat control for quality sealing. Configuration of the sealer can be set for either horizontal or vertical use. Height can be adjusted for each configuration. Seals are created using economical etched Teflon coated fiberglass bands and standard in-feed is right to left.. SPECIFICTIONS VOLTGE 0/0 VC NUMER OF PHSES FREQUENCY HET CPCITY MPERGE MXIMUM SPEED 50/60 Hz 00 W 905 cm/min TEMPERTURE RNGE 0 C - 80 C WEIGHT SEL WIDTH RNGE VERTICL DJUSTMENT 5 kg mm 6mm 750 mm 00 mm SELING ORIENTTION 0 or 90 ORIGINL INSTRUCTIONS Page

15 MPS700-M OPERTION MNUL. CONFORMITY Directive LOW VOLTGE MCHINERY SFETY EMC RoHS WEEE Number 006/95/EC 006//EC 00/08/EEC 00/95/EC 00/96/EC amended by 00/08/EC. MCHINE PRTS DIGRM Control ox Motor Stand In-feed Rail Sealing Section FIGURE ORIGINL INSTRUCTIONS Page

16 MPS700-M OPERTION MNUL.5 CONTROL OX FETURES Encoder Port Motor Port Printer/Embosser Port Power Off Cool Down Power Cord Power On Speed Controller Temperature Controller FIGURE - FIGURE - ORIGINL INSTRUCTIONS Page 5

17 MPS700-M OPERTION MNUL.6 STND FETURES Height djustment Stand Stem Leveling djustment Stand ase Mounting screws (On ottom) FIGURE -.7 DIMENSIONL DIGRM FIGURE - ORIGINL INSTRUCTIONS Page 6

18 MPS700-M OPERTION MNUL.0 UNPCKING ND SSEMLY To reduce any risk of damage during shipping, the MPS700-M series models are securely packed in three separate sections that need to be assembled. The three sections are the sealing section (consisting of the head and rails), the stand stem, and the stand base. Tools Required Number of Persons Needed. Philips Head Screwdriver. djustable Wrench CUTION: This assembly weighs in total over 8 kilograms, please use a minimum of two people to remove this from the box and to mount in its final position.. UNCRTING THE MPS700-M SERIES ) Open the box then remove the first layer of plastic wrap and foam to uncover the head and rails. Carefully lift the head and rails out of the box and set aside. ) Remove the second layer of wrap and foam to uncover the two stand sections the base and the stem. Remove each component separately and set aside.. SSEMLING THE MPS700-M SERIES ) The stand must first be assembled. To do so, remove the four supplied screws that are attached in the top section of the stand. ) Once the screws are removed, place the top of the stand into the base section as shown in Figure #. ) Replace the screws to attach the stem to the base, tightening firmly into place. ORIGINL INSTRUCTIONS Page 7

19 MPS700-M OPERTION MNUL ) Next, the sealing head (control box and rails) must be attached to the stand. Simply place the upper two support knobs on either side of the control box into the upper slots on the stand. Next, gently swing the sealing section down into place. The sealing section will be attached as in Figure #5. 5) Install the locking bolts to ensure the sealing section is held securely in place. Upper Support Knob Control ox Mounting racket Lower Support Locking olts FIGURE - 5. UNPCKING THE MPS70-M SERIES To reduce risk of damage during shipping, the MPS70-M table-top model is securely packed in one piece. If an optional product shelf was ordered, this piece will be packed separately and will need to be assembled to the MPS70-M. ) Open the box then remove the first layer of plastic wrap and foam to uncover the MPS70-M. Carefully lift the assembly out of the box and set aside. ORIGINL INSTRUCTIONS Page 8

20 MPS700-M OPERTION MNUL CUTION: This assembly weighs in total over 8 kilograms, please use a minimum of two people to remove this from the box and to mount in its final position. ) Remove the second layer of wrap and foam to uncover the product shelf. SSEMLING THE MPS70-M OPTIONL PRODUCT SHELF ) To assemble the product shelf, the mounting blocks must be attached first. ) Take the mounting blocks and screw them to the bridges on the guard assembly. ) Now attach the product shelf to the machine by screwing the shelf to the mounting blocks as shown in Figure #6. Mounting lock Product Shelf Guard FIGURE - 6 ORIGINL INSTRUCTIONS Page 9

21 MPS700-M OPERTION MNUL.0 OPERTION. GETTING STRTED ) If the MPS700-M series has been shipped without a power cord it is the responsibility of the owner to source and purchase a compatible power cord based on the criteria provided below. a. IEC 600 compliant. b. C Class Female Cable Connector, see figure 7. c. 5 / 50 VC minimum rating. d. Entire cable must be a maximum of.5 meters in length. e. Individual wire must be a minimum of 0.75 mm². Female Male FIGURE - 7 ) The main control box has three buttons on its front face which control the power of the machine. The machine has three different power modes but can only be in one mode at a time. The table below shows the different modes and which button controls each. POSITION Green Red Yellow FUNCTION POWER ON POWER OFF COOL DOWN TLE - ORIGINL INSTRUCTIONS Page 0

22 MPS700-M OPERTION MNUL ) efore you can begin sealing your product, it is important to follow the steps below. ) djust the MPS700-M to accommodate proper bag position either horizontal or vertical (refer to section.). 5) Set the three sealing variables: temperature, speed and pressure (refer to sections.,. and.5 respectively).. DJUSTING THE HED ORIENTTION The sealing head for the MPS700-M series model may be set either at 0 or 90 to the horizontal. To move the orientation of the sealing section from vertical to horizontal position, the sealing section must first be removed. ) Loosen and remove the locking bolts to free the sealing section from the frame. ) Lift the section up and away from the frame and set aside. ) Loosen and remove control box mounting bracket bolts. Reference Figure #5. ) Turn control box mounting brackets upside down and replace bolts and tighten down securely. Reference Figure #5. 5) On the sealing section remove the lower support knob (Refer to Figure #5) on the side of control box and move to the upper corner closer to the front of the box and tighten down securely. Repeat for opposite side of control box. 6) Next, the sealing section (control box and rails) must be reattached to the stand. Place what are now the upper two support knobs on either side of the control box into the upper slots on the stand. Next, gently swing the sealing section down into place. The sealing section will be attached as in Figure #8 left picture. 7) Install the locking bolts to ensure the sealing section is held securely in place. CUTION: The sealing section assembly weighs in total over 6 kilograms, please use a minimum of two people to remove sealing section to or from the frame ORIGINL INSTRUCTIONS Page

23 MPS700-M OPERTION MNUL FIGURE - 8. DJUSTING THE HED HEIGHT The sealing head height is easily adjusted via the crank mechanism on the stand. To increase the head height, rotate the wheel on top of the stand. See Figure # for location of the hand wheel on the stand.. SETTING THE SEL TEMPERTURE There are four buttons that operate the digital temperature controller and two digital displays as shown in Figure #9. Please refer to Figure # for the location of the temperature controller. ) The Level key Locked out. For maintenance use only. ) The Display key Locked out. For maintenance use only. ) The Up key Move the set point value up. ) The Down key Move the set point value down. 5) The Process Value display - the current temperature at which the machine is running. 6) The Set Value display - the temperature that has been selected for operation. ORIGINL INSTRUCTIONS Page

24 MPS700-M OPERTION MNUL 5 6 FIGURE - 9 The temperature controller is an auto-tune PID type, which should keep temperature constant. There is a lockout setting on the temperature controller to prevent users from changing the internal values of the temperature controller, if assistance is needed please get in touch with Plexpack Technical Support. Correct temperature setting can be determined by taking the time to test seal the samples of material to be used. Too much heat will result in a heavy seal that weakens the material above and below the seal while insufficient heat will result in a weak seal. The temperature of the MPS700-M series should range between 0 C to 80 C. ) Press the MODE button and then the arrow keys to either raise or lower the set point temperature to its desired value. ) Once you have selected the desired temperature, the controller retains the displayed value. ) The value in the Process Value screen will now change to match your selected temperature value. Once the Process Value matches the Set Value, the machine is ready to seal your product. ORIGINL INSTRUCTIONS Page

25 MPS700-M OPERTION MNUL.5 SETTING THE SEL SPEED To set or change the speed, use the up/down arrows on the digital speed control unit. See Figure # for location of the speed controller. The digital display on the speed control is set to read in meters per minute. e sure to record both speed and temperature settings for future reference. If you experience difficulties in obtaining an optimum seal, contact Plexpack Technical Support for assistance. Enter Current Speed Increase Decrease FIGURE -0.6 DJUSTING SELING ND COOLING R PRESSURE To adjust the sealing and cooling bar pressure the in-feed rail must be lowered. Due to the fact that this exposes the operator to moving components it is recommended that a qualified service technician perform this procedure. Refer to the maintenance manual for instructions. CUTION: Exposure to moving parts and hot surfaces if the proper precautions are not taken. Only qualified service technicians should attempt this procedure. Do not attempt if loose clothing, jewellery and/or hair are present, they may become entangled. ORIGINL INSTRUCTIONS Page

26 MPS700-M OPERTION MNUL.7 PROPER G FEEDING Feed the leading edge of the bag into the machine and lightly hold onto the trailing edge of the bag to avoid any bunching or creasing of the material. notch located on the infeed rail guide indicates the minimum height of the top of the bag when fed into the rails. The bridge has a slot showing the maximum height of the top of the bag capable of being fed through the machine. See Figure # for details. Slot in ridge Notch in Guide FIGURE - CUTION: There is a pinch hazard present during this operation. Do not let hands or fingers contact rotating components. Do not attempt if loose clothing, jewellery and/or hair are present, they may become entangled. ORIGINL INSTRUCTIONS Page 5

27 MPS700-M OPERTION MNUL.8 G SUPPORT CPILITY Product conveying belts hold the bag in position during the sealing process. The amount of weight capable of being supported by the conveying belts is directly proportional to the width and the thickness of the bag containing the product. The machine in-feed section is designed to support the bag as it runs through the sealer. Typically a 50mm wide L.D.P.E bag will support kg of product. More weight can be supported with wider bags and less weight can be supported as bag width narrows. If you see slippage of the bag a conveyor is recommended for additional support. Evidence of slippage will result in a stretched or torn seal..0 RELEVNT MISUSE The use of this machine for any other operation other than bag sealing is strictly prohibited. Failure to comply with these terms will result in damage to the machine, possible injury to the operator and will void the warranty of the machine. elow are some examples of relevant misuse, please refrain from these actions or any other action which can harm the operator or damage the machine.. MISPLCED LIQUIDS The MPS700-M is not waterproof and should not have liquids of any kind placed on the equipment at any time. CUTION: Electrical shock and damage to equipment will be a direct result of placing liquids on the machine. ORIGINL INSTRUCTIONS Page 6

28 MPS700-M OPERTION MNUL. USE OF NON PPROVED LURICNTS The MPS700-M comes from the factory containing specific lubricants on two separate parts of the machine the gear box and the product conveying belts contained within the in-feed rail assembly. Please use lubricants which meet or exceed the specifications of the factory installed lubricants shown in table below. CUTION: Only qualified service personnel should attempt replacing the lubricants on this machine, please refer to the maintenance manual for procedures. LOCTION GER OX CONVEYING ELTS TYPE/SPECIFICTION Multipurpose Lithium Soap ased grease NLGI Grade Lubricating grease Food Grade Non-Toxic Clear Grease road operating temperature, with a high dropping point TLE -. STNDING ON THE MCHINE The MPS700-M series is a physically stable design however by no means should one attempt to stand or rest on any part of the machine. Do not attempt to place any other items on the machine which can cause the machine to become unstable. CUTION: Do not attempt to stand on or place any other items on any part of the machine. The equipment may become unstable and pose a risk of tipping on to the operator causing bodily harm. ORIGINL INSTRUCTIONS Page 7

29 MPS700-M OPERTION MNUL. SELING OVER FILLED GS The MPS700-M is not designed to have over filled bags or obstruct objects fed through the conveying or sealing sections of the machine. The product in the bag being sealed must remain below the in-feed rail at all times. Only have the bag itself should be fed through, failure to comply will result in damage to the machine and a void warranty. 5.0 CLENING THE MCHINE In the event that the machine must be cleaned, please ensure that the main power switch has been turned to the off position and the main power cord has been disconnected and locked out. Failure to comply may result in damage to the machine and /or personal injury. CUTION: Cleaning the machine while it is energized and/or running can result in entanglement and electric shock causing bodily harm. Do not attempt if loose clothing, jewellery and/or hair are present, they may become entangled. ORIGINL INSTRUCTIONS Page 8

30 MPS700-M OPERTION MNUL 5. SURFCE CLENING If liquid has been spilled on the surface of the machine but has not entered the internal areas of the machine proceed to wipe the area dry with a cloth or paper towel. Stubborn materials may be scrubbed off the surface of the machine with a damp cloth and a light cleaning solution if needed. Do not allow moisture from the cloth or the cleaning solution itself to enter the internal area of the machine as this can damage the electrical and mechanical components contained within. Gently spraying compressed air is another means of eliminating dirt from the machine s interior. CUTION: ll spills located on the floor directly in the operators foot print must also be immediately cleaned to prevent people from slipping and falling while operating the machine. 5. INTERNL CLENING If a liquid or any other debris has entered the internal areas of the machine such as a product bag exploding or a drink being spilled on the machine please refrain from opening the machine. qualified service technician is required for the opening of the machine. Refer to the maintenance manual for procedures. 5. MICRO IOLOGICL MTERILS In the event that the environment around the machine or the product being sealed in the bags is a biohazard and has leaked, spilled or exploded on the machine do not attempt to ORIGINL INSTRUCTIONS Page 9

31 MPS700-M OPERTION MNUL clean. Please refer to plant safety protocol for handling such materials and the maintenance manual for this machine to access the internal areas of the machine. Only qualified service personnel should attempt cleaning the machine. 6.0 RECYCLING OF MCHINE The Waste Electrical and Electronic Equipment (WEEE) Directive is a European law, which came into effect in the UK on July st 007. It's designed to reduce the amount of WEEE going into landfills. This means that all manufacturers will be responsible for the disposal of old electrical goods in an environment friendly way. 7.0 MINTENNCE Please refer all maintenance of this machine to a qualified service technician, review the maintenance manual for procedures and safety information while performing maintenance. ORIGINL INSTRUCTIONS Page 0

32 MPS700-M MINTENNCE MNUL MPS700-M MINTENNCE MNUL ORIGINL Page xii

33 MPS700-M MINTENNCE MNUL CONTENTS Precaution.0 General Procedures. De-energizing and Lockout Procedure. Heating ar Cooling Time. Opening the Control ox. Lowering the In-Feed Rails.5 Raising the In-Feed Rails.6 djusting the Seal and Cooling ar Pressure.0 Maintenance. Replacing Teflon ands (MPS700-M). Replacing Teflon ands (MPS70-M). Removing Product Conveying elts. Installation of Product Conveying elts.0 Preventative Maintenance. Cleaning the Interior.0 Trouble Shooting Guide ORIGINL Page xiii

34 MPS700-M MINTENNCE MNUL CUTION: To ensure the safety of the service technician this manual and the operator manual must be read and understood before proceeding. This document has been produced by: Plexpack Corporation 60 irchmount Road, Unit. Toronto, Ontario MP 8 Canada The directives in this document are in accordance with the design and construction of the unit at the time it was released by the Plexpack production facility. ORIGINL INSTRUCTIONS Page

35 MPS700-M MINTENNCE MNUL.0 GENERL PROCEDURES. DE-ENERGIZING ND LOCKOUT PROCEDURE CUTION: Risk of electrical shock if the machine has not been properly de-energized and locked out prior to performing maintenance procedures. ) First the machine must be powered off using the RED button on the front of the control box. Press this button to power off the machine. ) Proceed to unplug the main power cord from the wall outlet or the back of the control box. To lockout the machine the main power cord must be COMPLETELY REMOVED and in the possession of the service technician at all times.. HETING R COOLING TIME The heating bars of the MPS700-M operate between 0 C and 80 C which can cause serious burns if touched by the service technician. The table below shows average cooling times from the maximum temperature of 00 C over a time lapse of ten minutes. When the YELLOW button (cool down mode) on the front of the control box is pressed the machine will continue to operate for ten minutes however the heater bars will not be energized allowing the machine to cool down. When servicing the machine be aware of the possible dangers posed by the temperature of the sealing bars. CUTION: Hot surfaces may be exposed. To prevent personal injury do not attempt to touch the heating bars or surrounding areas while hot. ORIGINL INSTRUCTIONS Page

36 MPS700-M MINTENNCE MNUL TIME TEMPERTURE (minutes) ( C) TLE -. OPENING THE CONTROL OX The control box must be opened to perform certain maintenance procedures. This procedure must always be followed in order to reduce the risk of injury to the service technician. Tools Required Number of Persons Needed. METRIC LLEN KEYS ) Once the machine has been locked out in a de-energized state it is now safe to loosen off the two bolts in the lower front corners of the control box as shown in Figure #. ) The front panel may now be lifted up to access the inside of the control box. Socket Head Cap Screws FIGURE - ORIGINL INSTRUCTIONS Page

37 MPS700-M MINTENNCE MNUL. LOWERING THE IN-FEED RILS The in-feed rails containing the product conveying belts must be lowered to perform certain maintenance procedures on the machine. This procedure must be followed in order to prevent damage to the machine and injury to the service technician. The rails of the MPS700-M may only be lowered while the machine is in a de-energized locked out state, follow procedure.. Tools Required Number of Persons Needed. METRIC LLEN KEY ) Once the machine has been locked out in a de-energized state it is now safe to loosen off the two thumb screws shown in Figure #. ) Hold the rail in position with one hand while loosening the thumb screws with the other hand. ) Once both screws have been backed off completely, gently allow the rail to swing down toward the stand. Thumb Screws FIGURE - ORIGINL INSTRUCTIONS Page

38 MPS700-M MINTENNCE MNUL.5 RISING THE IN-FEED RILS If the in-feed rails have been lowered to perform maintenance it will be necessary to raise them once finished. Simply reverse the procedure shown in section.5 to raise the rails back into position. If the drive pulleys or gears have rotated while the in-feed rails have been lowered it will be necessary to raise the rails while the machine is running at a very low speed. This procedure presents exposure to moving components and can cause injury if not careful. CUTION: Rotating and moving components are exposed. Use extreme caution to avoid entanglement causing personal injury. Do not attempt if loose clothing, jewellery and/or hair are present, they may become entangled. ) If the rails fail to snap into place, the alignment of the drive pulleys has shifted out of position. ) To realign the pulleys, you must reconnect the power to the machine if it was disconnected and turn the machine to the COOL position to prevent the heaters from activating. ) djust the speed to a very low value. ) s the machine runs, very carefully ease the in-feed rails back into position, some force may be needed to snap the rail into place. 5) t this point, the rails should have snapped into place. Turn off machine and continue. 6) While holding the rails in place, tighten the two thumb screws shown in Figure #. ORIGINL INSTRUCTIONS Page 5

39 MPS700-M MINTENNCE MNUL.6 DJUSTING THE SELING ND COOLING R PRESSURE To adjust the sealing and cooling bar pressure, please follow this procedure. Tools Required Number of Persons Needed. Philips Head Screwdriver ) The machine must first be locked out, follow procedure. ) There is exposure to hot surfaces if the machine is not cooled down properly, please follow procedure. ) The rail must be lowered, follow section.. ) Once the rail is lowered, tighten or loosen the spring knobs to increase or decrease the pressure of the bars. Refer to figure #. Spring Tension Knobs FIGURE - ORIGINL INSTRUCTIONS Page 6

40 MPS700-M MINTENNCE MNUL.0 MINTENNCE When performing maintenance procedures it is a good rule of thumb to inspect the sealing bars for built up molten plastic which can eventually become a fire hazard. To maintain consistent sealing inspect the bars for scratches or dents and if they are present replace them sealing bars. Tools Required. Metric llen Keys. djustable Wrench Number of Persons Needed. REPLCING TEFLON NDS (MPS700-M) Plexpack Teflon bands are available on a -hour turn-around basis. Contact your dealer or the Plexpack service group at ) It is necessary to follow the lockout procedure., and be aware of section. which states the cooling times of the sealing bars before continuing. CUTION: The sealing bars are extremely hot when machine is running be sure to allow bars to cool to avoid personal injury. ) Next, you will need to lower the rails. Refer to section. for procedure. 5) fter the rails have been lowered you must remove the tension on the Teflon bands by turning both tension knobs shown in Figure # counterclockwise. ORIGINL INSTRUCTIONS Page 7

41 MPS700-M MINTENNCE MNUL Tension Knobs FIGURE - 6) The cooling and sealing bar pressure will also need to be released follow procedure.6 and figure for details. 7) Remove the old bands and clear any band fragments that may be present. This is also an ideal time to clean the seal bars, refer to section. for information. 8) Place the new bands between the heating and cooling bars. This is accomplished by gently pulling up on the pressure plates shown in Figure #5, then sliding the Teflon band between the front and the rear sealing/cooling bars. ORIGINL INSTRUCTIONS Page 8

42 MPS700-M MINTENNCE MNUL Pressure Plates Cooling ars Heating ars FIGURE - 5 9) Slide the bands up the pulleys on both ends and try to centre them on the pulleys and on the sealing/cooling bars. 0) Raise the rails by following the procedure in section.6 ) Tension the bands by turning the tension knobs clockwise. Do not over-tension. djustment of the bands is critical if the bands are too tight, they may break.. REPLCING TEFLON NDS (MPS70-M) To replace the Teflon bands for the table-top model, follow these steps: ) It is necessary to follow the lockout procedure., and be aware of section. which states the cooling times of the sealing bars before continuing. CUTION: The sealing bars are extremely hot when machine is running be sure to allow bars to cool to avoid personal injury. ORIGINL INSTRUCTIONS Page 9

43 MPS700-M MINTENNCE MNUL ) Next, you will need to remove the guarding. The guarding is removed by loosening the two bolts shown in Figure #6. Socket Head Cap Screw Thumb Screw FIGURE - 6 ) fter the guarding has been removed the cooling and sealing bar pressure will also need to be released follow procedure.6 and figure for details. ) Next the tension on the Teflon bands must be released by turning both tension knobs shown in figure counterclockwise. 5) Remove the old bands and clear any band fragments that may be present. This is also an ideal time to clean the seal bars, refer to section. for information. 6) Place the new bands between the heating and cooling bars. This is accomplished by gently pulling up on the pressure plates shown in Figure #5, then sliding the Teflon band between the front and the rear sealing/cooling bars. 7) Slide the bands up the pulleys on both ends and try to centre them on the pulleys and on the sealing/cooling bars. 8) Install the components removed in step of this procedure. 9) Tension the bands by turning the tension knobs clockwise. Do not over-tighten. djustment of the bands is critical if the bands are too tight, they may break. ORIGINL INSTRUCTIONS Page 0

44 MPS700-M MINTENNCE MNUL. REMOVING PRODUCT CONVEYING ELTS ) It is necessary to follow the lockout procedure., and be aware of section. which states the cooling times of the sealing bars before continuing. ) If your sealer is equipped with a trimmer, embosser, or printer, you must remove these units first. Please refer to the appropriate ddendum to this manual for instructions on how to remove these units properly. ) The entire in-feed rail must be removed from the head section in order to replace the product conveying belts. It is recommended that two people aid in this procedure. s one person supports the rail section, have the other person unscrew and remove the thumb screws that allow the rails to swing down shown in Figure #. ) Next, as one person is supporting the rails in the original upright sealing position, the other person needs to remove the two screws that are located in the rails hinges found under the control box. 5) Completely remove the rails from the machine. 6) Remove the two bridges that join the rails together shown in Figure #8, by removing the Phillips screws located on the opposite side. There are four screws for each bridge that need to be removed. 7) With a Phillips screwdriver, remove all the protective covers. 8) Loosen, but do not remove, the tension pulley located at the in-feed end of the rail shown in Figure #8 (i.e. the pulley that rides in the slot) by loosening its bolts located on the opposite side. 9) The belt can now be removed by unwinding it from the drive pulley section, and unwrapping it from both tension pulleys. ORIGINL INSTRUCTIONS Page

45 MPS700-M MINTENNCE MNUL ridges Tension Pulleys FIGURE - 8. INSTLLING PRODUCT CONVEYING ELTS ) t this point it is assumed that you have already completed the procedure in section.. ) Feed the conveying belts around the pulleys on both ends and thread it through the driving pulleys. ) Tighten the in-feed pulleys. ) ttach the two bridges that join the rails together, by tightening the Phillips screws located on the bottom of the rails. There are four screws that hold the bridges to the rails. 5) pply food grade grease or an equivalent to the specifications shown in section. of the operator s manual to the drive coupler and a pea size amount spreading it over the notched side of the belt itself. The grease will spread around the entire belt once the machine is started so you only need apply in one area. This will prevent the belts from flaking and will help extend the life of the belt. ORIGINL INSTRUCTIONS Page

46 MPS700-M MINTENNCE MNUL 6) Next, as one person is supporting the rails in the original upright sealing position, the other person needs to insert & tighten the two screws that are located in the rails hinges found under the control box. 7) Once the in-feed rail has been securely re-attached it is now safe to reinstall the optional printer, embosser and/or trimmer if equipped..0 PREVENTTIVE MINTENNCE Routine cleaning, lubrication and care will improve the running and extend the longevity of your machine. Frequency of cleaning is largely dependent upon your production environment; highly corrosive environments require more frequent cleaning than noncorrosive environments. The machine should be cleaned once every two weeks.. CLENING THE INTERIOR Never use corrosive solvents when cleaning the MPS. Water and light liquid detergents, along with a clean cloth are all that is needed to clean the interior of the machine. CUTION: Never subject this machine to a wash-down procedure or expose the internals of the machine to liquids of any kind. This will damage the electrical and mechanical components of the machine. ORIGINL INSTRUCTIONS Page

47 MPS700-M MINTENNCE MNUL.0 TROULE SHOOTING GUIDE Fault Machine will not run when on/off switch appears to be on Motor is running, but The bags are not Feeding through the Machine The bags are not sealing properly ags are melting or burning Probable Cause Cure Reference. Power is not getting to the machine.. Make sure machine is plugged in.. Check power switch to make sure it is in the on position.. lown Fuse.. Check / change fuse in control box.. Check the main breaker panel to see if breaker switch has been tripped Section. Section. Contact Plexpack Technical Support Group Contact Plexpack Technical Support Group. Faulty speed controller.. Check for loose wiring Contact Plexpack Technical Support Group.. Check the voltage across the motor. It should be 90 VDC at full load. If readings are under 0 VDC, you may have to replace your controller.. Faulty motor.. If the voltage and fuses are okay, then you will need to replace the motor.. roken product conveying belt. roken motor timing belt. Improper temperature setting and/or speed. Improper sealing bar setting. Temperature is set too high. ags weight dragging band down. Heating bar surface is exposed.. djust product conveying belt tension.. Replace product conveying belt Contact Plexpack Technical Support Group Contact Plexpack Technical Support Group Section. Section... Replace timing belt Contact Plexpack Technical Support Group.. djust the temperature and/or speed setting.. The sealing bars need to be reset Section. Section. Contact Plexpack Technical Support Group.. Reduce the temperature Section... Ensure product weight is no more than 0.9 kilograms for those models without a conveyor.. Make sure Teflon bands are tracking properly Section.7 Section. ORIGINL INSTRUCTIONS Page

48 MPS700-M SPRE PRTS LIST 5.0 MPS700-M RECOMMENDED SPRE PRTS LIST Part Number Description Recommend Qty. P599 HETER CONTROL RELY P0 TEFLON ND 57 X X 6 MIL 0 Q07M TEFLON ELT DRIVE ROLLER 0 Q006 TEFLON ELT TENSION PULLEY 0 Q07 FLOT FOR TEFLON ELT DRIVE ROLLER P505 SHOULDER OLTS FOR FLOT P009 HETER CRTRIDGE 0V.5 P00 HETER CRTRIDGE 0V 5.0 P67 HETER CRTRIDGE 0V.5 P68 HETER CRTRIDGE 0V 5.0 Q06M HETER R / SEL.5 0 Q000 HETER R /8 SEL.5 0 Q0M HETER R /8 SEL Q05M HETER R / SEL Q000 HETER R /8 SEL Q0M HETER R / SEL PE006 TEMPERTURE CONTROL PNSONIC KT 0 P578 DIGITL TCHOMETER 0 P500 MOTOR CONTROL RELY 0V 0 P50 MOTOR CONTROL RELY 0V 0 P00 MOTOR TIMING ELT 50L050 P0098 INFEED ELT 05H07 Q0 MOLDED PRESSURE R 0 P00 ERING SR6 0 P005 ERING SR8 0 PEF0007 FUSE 50V GLSS PEF00 FUSE 5 50V ORIGINL Page xiv

49 MPS700-M SPRE PRTS LIST Optional ag Top Trimmer Parts P0096 TRIMMER LDE Q099M TRIMMER LDE LEFT HND THRED SCREW Q08 TRIMMER CK-UP ROLLER P096 TRIMMER ELT 0XL07 P097 TRIMMER ELT 50XL07 P08 TRIMMER ELT 80XL07 Option Emboss Coder Parts E0009M EMOSSER CK-UP ROLLER 0 P006 EMOSSER- PRINTER CLUTCH 0V 0 P EMOSSER- PRINTER CLUTCH 0V 0 P050 EMOSSER POWER CORD NORTH MERIC ONLY 0 P007 EMOSSER-PRINTER MICRO SWITCH COVER 0 EMOSSER TYPE STD. (USE TYPE '' S PRT NUMER, FOR EXMPLE) 0 EMOSSER TYPE THIN (USE TYPE '' S PRT NUMER, FOR EXMPLE) 0 P008 EMOSSER-PRINTER MICRO SWITCH 0 Optional Dry Ink Printer Parts P086 PRINTER POWER CORD 0 P007 EMOSSER-PRINTER MICRO SWITCH COVER 0 P008 EMOSSER-PRINTER MICRO SWITCH 0 PRINTER TYPE (USE TYPE '' S PRT NUMER, FOR EXMPLE) 0 Toll Free: x 8 Fax Number: info@plexpack.com Website: ORIGINL Page xv

50

51

52

53

54 ITEM DRWG # Q508 C60M MPS700-M TITLE CONV. STND - MPS700-M C-6-6 CONVEYOR MPS700-M MPS7500-M QTY UNLESS OTHERWISE SPECIFIED DIMENSIONS RE IN INCHES TOLERNCES: X/X +/-.05 X +/-.05 X.X +/-.05 X.XX +/-.00 X.XXX +/-.005 NGLES 5 DEURR & REK SHRP EDGES TITLE PLEXPCK MPS700-M SELER WITH CONVEYOR THIRD NGLE PROJECTION MODEL MTERIL MPS7000-M DTE DRFTER 08//0 CHECKER 7/07/00 DESIGN'R 08//0 Y CD MM M MT'L P/N FINISH DWG SIZE SCLE SHEET LENGTH: PRT NUMER: MPS7500-M REV 00

55 MPS7500-M in / 09 mm MX 5 / in / 896 mm MX 55 / in / mm 9 / in / 7 mm / in / 60 mm MIN 9 / in / 7 mm MIN / in / 6 mm / in / 80 mm 6 in / 5 mm 0 / in / 775 mm UNLESS OTHERWISE SPECIFIED DIMENSIONS RE IN INCHES TOLERNCES: X/X +/-.05 X +/-.05 X.X +/-.05 X.XX +/-.00 X.XXX +/-.005 NGLES 5 DEURR & REK SHRP EDGES TITLE PLEXPCK MPS700-M SELER WITH CONVEYOR THIRD NGLE PROJECTION MODEL MTERIL MPS7000-M 8 in / 08 mm DTE DRFTER 08//0 CHECKER 7/07/00 DESIGN'R 08//0 Y CD MM M MT'L P/N FINISH DWG SIZE SCLE SHEET LENGTH: PRT NUMER: MPS7500-M REV 00

56 ITEM 5 6 DRWG # Q500 Q50 Q50 Q505 Q005M Q059M TITLE NON-VLIDTELE CONTROL OX INFEED RIL SSEMLY MPS700 SEL SECTION MPS700-M STND DRIVE SSEMLY TENSIONER SSEMLY MPS700-M QTY 6 5 UNLESS OTHERWISE SPECIFIED DIMENSIONS RE IN INCHES TOLERNCES: X/X +/-.05 X +/-.05 X.X +/-.05 X.XX +/-.00 X.XXX +/-.005 NGLES 5 DEURR & REK SHRP EDGES TITLE PLEXPCK MPS700-M NON VL. G SELER - 0V THIRD NGLE PROJECTION MODEL MTERIL MPS7000-M STINLESS DTE DRFTER 08//0 CHECKER DESIGN'R 08//0 CD Y MM M MT'L P/N FINISH DWG SIZE 80 GRIT SCLE SHEET PRT NUMER: LENGTH: MPS700-M REV 00

57 MPS700-M in / 09 mm MX 55 / in / mm 5 / in / 5 mm 9 / in / 7 mm MIN / in / 87 mm / in / 80 mm 6 / in / 69 mm / in / mm 0 / in / 5 mm UNLESS OTHERWISE SPECIFIED DIMENSIONS RE IN INCHES TOLERNCES: X/X +/-.05 X +/-.05 X.X +/-.05 X.XX +/-.00 X.XXX +/-.005 NGLES 5 DEURR & REK SHRP EDGES TITLE PLEXPCK MPS700-M NON VL. G SELER - 0V THIRD NGLE PROJECTION MODEL MTERIL MPS7000-M STINLESS DTE DRFTER 08//0 CHECKER DESIGN'R 08//0 CD Y MM M MT'L P/N FINISH DWG SIZE 80 GRIT SCLE SHEET PRT NUMER: LENGTH: MPS700-M REV 00

58 Q500 ITEM PRT NUMER P000 P09 P09 P060 P065 P068 P069 P070 P078 P65 P599 P5 P5 P56 P59 P578 P50 Q000 Q00 Q00 Q0 Q0 Q0 Q0 Q05 Q06 Q6 Q9 P095 P067 P00 P0 P7 Q07 PE006 PES00 PES0 PES0 PES05 PES07 TITLE FILTER, RFI LINE DETCHLE POWER CORD SNP USHING PIN MLE RECEPTCLE PLUG FEMLE C RECEPTICL PLTE HOLE PLUG DJUSTLE HINGE SELF-CLINCHING STUD SNP IN PLUG 7/8" SOLID STTE RELY PIN CONTCT SOCKET CONTCT SQURE FLNGE RECEPTCLE PIN, FEMLE DIGITL MOTOR SPEED CONTROL SQURE FLNGE RECEPTCLE CONTROL OX SIDE PLTE, LEFT CONTROL OX SIDE PLTE, RIGHT OTTOM COVER - MPS7000-M FILLER PIECE HINGE MOUNTING R CONTROL OX MIN SPCER CK COVER - MPS700-M FRONT COVER - MPS700-M INTERNL PNEL - MPS7000-M TRIMMER COVER LEL - MPS700 FRONT COVER RELY SOCKET MODULR FUSE TERMINL ERTH TERMINL END CLMP FEED THROUGH TERMINL DIN RIL 65 TEMPERTURE CONTROLLER SWITCH, SFETY INTERLOCK DOOR OMRON DOOR SWITCH KEY PUSH UTTON GREEN SOLID PUSH UTTON YELLOW LITE PUSH UTTON GREEN SOLID QTY UNLESS OTHERWISE SPECIFIED DIMENSIONS RE IN INCHES TOLERNCES: X/X +/-.05 X +/-.05 X.X +/-.05 X.XX +/-.00 X.XXX +/-.005 NGLES 5 DEURR & REK SHRP EDGES THIRD NGLE PROJECTION 5 5 TITLE 0 MODEL MTERIL 9 8 PLEXPCK NON-VLIDTELE CONTROL OX MPS700-M DTE DRFTER 0/0/0 CHECKER 05/0/009 DESIGN'R 0/0/0 CD Y M.M. M.M. MT'L P/N FINISH DWG SIZE SCLE SHEET PRT NUMER: Q500 LENGTH: REV 00

59 Q UNLESS OTHERWISE SPECIFIED DIMENSIONS RE IN INCHES TOLERNCES: X/X +/-.05 X +/-.05 X.X +/-.05 X.XX +/-.00 X.XXX +/-.005 NGLES 5 DEURR & REK SHRP EDGES TITLE PLEXPCK NON-VLIDTELE CONTROL OX THIRD NGLE PROJECTION MODEL MTERIL MPS700-M DTE DRFTER 0/0/0 CHECKER 05/0/009 DESIGN'R 0/0/0 Y CD M.M. M.M. MT'L P/N FINISH DWG SIZE SCLE SHEET LENGTH: PRT NUMER: Q500 REV 00

60 Q50 ITEM PRT NUMER TITLE QTY E0005 CODER MOUNTING PIN COLLR P07-L DJUSTLE COMPRESSION HINGE P07-R P0 Q009 Q009 Q005 DJUSTLE COMPRESSION HINGE TREDED SPCER HINGE SPCER CODER MOUNTING PIN, FRONT FLEX GURD MOUNTING SPCER Q0 Q0 Q0760 Q076 PRESSURE R PINCH GURD INFEED NGLE RIL RIDGE SUPPORT RCKET Q076 Q0768 Q0769 INFEED NGLE RIL RIDGE EXIT GUIDE PLTE, CK EXIT GUIDE PLTE, CK 0. 5 Q0770 ENTRY GUIDE PLTE, FRONT 6 Q077 ENTRY GUIDE PLTE, CK 7 8 Q7 Q0066M LEXN COVER G ENTRY GUIDE, CK Q0067M Q0076 G ENTRY GUIDE, FRONT G ENTRY GUIDE, FRONT 6 Q0077 G ENTRY GIDE, FRONT Q0078M EXIT GURD Q0079 X09 Q06M Q06M QS00M P00 Q006M GUIDE LOCK RIL SPCER LOCK INFEED RIL RER - MPS7000-M INFEED RIL FRONT - MPS7000-M DISCHRGE ELT GUIDE PULLEY SSEMLY RDIL LL ERING, SR6 INFEED DRIVE PULLEY STU SHFT Q0065 QS00M P00 P5060 INFEED TENSION PULLEY COGGED TIMMING PULLEY SSEMLY RDIL LL ERING, SR6 DOWEL PIN Q070 Q07M QS00 P00 P0570 Q005 Q0068 INFEED DRIVE TIMING PULLEY INFEED DRIVE PULLEY STU SHFT TENSION PULLEY SSY RDIL LL ERING, SR6 RETINING RING INFEED STU ROLLER SHFT SNU ROLLER QS005M P00 Q006M Q0065 INFEED GUIDE PULLEY SSEMLY RDIL LL ERING, SR6 INFEED TENSION PULLEY STU SHFT INFEED TENSION PULLEY UNLESS OTHERWISE SPECIFIED DIMENSIONS RE IN INCHES TOLERNCES: X/X +/-.05 X +/-.05 X.X +/-.05 X.XX +/-.00 X.XXX +/-.005 NGLES 5 DEURR & REK SHRP EDGES TITLE PLEXPCK INFEED RIL SSEMLY THIRD NGLE PROJECTION MODEL MTERIL MPS7000-M OM DTE DRFTER 06/0/008 CHECKER 6/0/0 DESIGN'R 06/0/008 Y M MM M MT'L P/N FINISH DWG SIZE NONE SCLE SHEET LENGTH: PRT NUMER: Q50 REV 00

61 / 7 /8 7 /8 Q50 / 6 /8 6 /8 UNLESS OTHERWISE SPECIFIED DIMENSIONS RE IN INCHES TOLERNCES: X/X +/-.05 X +/-.05 X.X +/-.05 X.XX +/-.00 X.XXX +/-.005 NGLES 5 DEURR & REK SHRP EDGES TITLE PLEXPCK INFEED RIL SSEMLY THIRD NGLE PROJECTION MODEL MTERIL MPS7000-M OM DTE DRFTER 06/0/008 CHECKER 6/0/0 DESIGN'R 06/0/008 Y M MM M MT'L P/N FINISH DWG SIZE NONE SCLE SHEET LENGTH: PRT NUMER: Q50 REV 00

62 Q ITEM DRWG # P00 P00 P05 P056 P087 P088 P06 P06 P6 P76 P5 Q007 Q068 Q09 Q0870 Q087 Q0880 Q08 Q09 Q00 Q0 Q5 Q5 Q05M Q00M Q066 Q069 TITLE CRTRIDGE HETER, 60W, 0 VC DUL THERMOCOUPLE, J-TYPE SNP DISK THERMOSTT FIRE WSHER COMPRESSION SPRING, COOLING R NYLON SHOULDER USHING SLOTTED SPRING TENSION SPRING THUMSCREW_KNO FN FN COVER DIN RIL SSM 7000 SEL SEC. COOLING R MTG. PLTE STRIN-RELIEF WIRE LOCK SPCER WIRE COVER HETING & COOLING R MTG. PLT SE MOUNTING PLTE COOLING R FIXED HETING R SPCER 0. LG FIXED HETING R SPCER 0.8 LG COOLING R SPCER, 0.55 LONG SELING SECTION R G GUIDE RH - MPS7000-M G GUIDE - LH HETING R /" x 5" LG COOLING R FN COVER PLTE COMMON WIRE COVER QTY UNLESS OTHERWISE SPECIFIED DIMENSIONS RE IN INCHES TOLERNCES: X/X +/-.05 X +/-.05 X.X +/-.05 X.XX +/-.00 X.XXX +/-.005 NGLES 5 DEURR & REK SHRP EDGES THIRD NGLE PROJECTION DTE DRFTER 8/0/008 CHECKER 0/0/008 DESIGN'R 8/0/008 Y Larryl M.M..M. TITLE MODEL MTERIL MT'L P/N FINISH DWG SIZE PLEXPCK MPS700-M SCLE SHEET MPS700 SEL SECTION PRT NUMER: Q50 LENGTH: REV 00

63 5 Q UNLESS OTHERWISE SPECIFIED DIMENSIONS RE IN INCHES TOLERNCES: X/X +/-.05 X +/-.05 X.X +/-.05 X.XX +/-.00 X.XXX +/-.005 NGLES 5 DEURR & REK SHRP EDGES TITLE PLEXPCK MPS700 SEL SECTION THIRD NGLE PROJECTION MODEL MTERIL MPS700-M DTE DRFTER 8/0/008 CHECKER 0/0/008 DESIGN'R 8/0/008 Y Larryl M.M..M. MT'L P/N FINISH DWG SIZE SCLE SHEET LENGTH: PRT NUMER: Q50 REV 00

64 Q505 ITEM PRT NO. TITLE QTY F9508 CRNK SUPPORT SPCER P0 FOOT LEVELING M6 Q0 MPS6000-CE CRNK SSEMLY. F900 PLSTIC DRIVE PLTE USHING 5.. F90 P07 WSHER THRUST ERING. Q05 INTERNL SIDE PLTE DETIL Q06 Q07 Q08 Q055 Q00 Q0 Q050 Q05 Q05 Q05 Q09 Q0 Q Q5 STND CME THRED SCREW ROD SIDE PLTE GUIDE SIDE PLTE GUIDE THRUST ERING LOCK HNDLE ERING MOUNT CRNK HNDLE SHFT TIMING PULLEY SELER SUPPORT PLTE SPCER SLIDING SPCER TOP FRME WELDMENT OTTOM FRME WELDMENT STND TOP PLTE STND COVER - MPS7000-M 5 6 Q006M M009 P005 TIMING PULLEY (P05 MODIFIED) INFEED CONVEYOR DJ. WHEEL FLNGE USHING /" x /" x /" UNLESS OTHERWISE SPECIFIED DIMENSIONS RE IN INCHES TOLERNCES: X/X +/-.05 X +/-.05 X.X +/-.05 X.XX +/-.00 X.XXX +/-.005 NGLES 5 DEURR & REK SHRP EDGES TITLE PLEXPCK MPS700-M STND THIRD NGLE PROJECTION DTE DRFTER /05/0 CHECKER 6/0/0 DESIGN'R /05/0 Y M M M MODEL MTERIL MT'L P/N FINISH DWG SIZE MPS7000-M OM Q505 NONE SCLE SHEET LENGTH: PRT NUMER: Q505 REV 0