Kawasaki Teryx 2 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Owner s Manual
|
|
- Kenneth Hancock
- 6 years ago
- Views:
Transcription
1 Owner s Manual Model: Kawasaki Teryx 2 Kawasaki Teryx 2 Cab Kit* Caution: efore using this product, read this manual and follow all Safety Instructions. Safety Instructions Cab Kit Contents Hardware ssembly Panel ssembly Operation *DefenderCab and accessories are in no way affiliated With Kawasaki Heavy Industries Ltd. ny use of the name is only to identify their utility vehicle as it pertains to our accessories. Kawasaki and Teryx are registered trademarks of Kawasaki heavy industries Ltd. 1
2 Warning: Failure to heed all safety and operating instructions and warnings regarding use of this product can result in serious bodily injury. SFETY INSTRUCTIONS Read entire assembly instructions before beginning work. Install all parts indicated in assembly instructions. Failure to fully assemble product before use could result in personal injury. ssembly of product requires use of hand or power tools. If you are not experienced in using these types of tools, have product dealer do the installation for you. Some parts contain sharp edges as indicated in the manual. Wear protective gloves if necessary. Dress for safety. DO NOT wear loose clothing, gloves, neckties or jewelry if using power tools to assemble this product. lways keep your assembly area clean, uncluttered and well lit. Keep visitors and children a safe distance away from the assembly area. Visitors should wear the same safety equipment described above. Never operate your TV with the cab doors open. Failure to properly latch the doors before moving the vehicle could result in serious injury. 2
3 C KIT CONTENTS Your DefenderCab should contain the parts listed below. Separate all parts from packing materials. Do not discard packing material until assembly is complete. Item quantities are listed in parenthesis below. Hardware Panels, Doors and rackets (2) 1 ¾ Clamps (1) Windshield Panel (2) Door Lever Knobs (1) ack Panel ssembly (2) Windshield Spacers (1) L-H Front Door ssembly (1) 25ft Roll, Hard Gasket (1) R-H Front Door ssembly (1) 25ft Roll, Soft Gasket (1) L-H Front Filler (8) Door ushings (1) R-H Front Filler (1) Hardware ag (1) L-H Door Upper Filler (96 ) Edge Trim 5/8 ulb (1) R-H Door Upper Filler (2) Door Frame umpers (2) Face Plate (1) R-H Front Door Lever (1) L-H Front Door Lever 3
4 Hardware bag will contain: 1/4-20unc 3/4" lg button head socket cap, SS 5 1/4-20unc 1/2" lg button head socket cap, SS unc 1" lg button head socket cap, SS Nylon lock nut 2 Washer.26" i.d.55" o.d Stainless steel 30 Washer.406" i.d -.875" o.d Stainless steel 36 ond seal galvanized washer #14x5/8 small i.d 23 1/4-20 Nylon Lock Nut 2 1/4-20 Flanged lock nut 10 M6x1.00, 8mm, Pan Head Phillips Screw, Zinc Plate 2 M6x1.00, 16mm, Pan Head Phillips Screw, Zinc Plate 4 5/16-18 x 3/4" flanged bolt 4 5/16-18 x 1 3/4" Hex Cap Screw 8 5/16-18 hex reg nut 8 5/16-18 Heavy Nyloc Nut, Ylw. Zn. Pl. 12 Push Type Retainer, 1/4", Phillips,LCK 16 #8 x 1/2" Sheet Metal Screw, Truss Head, Phillips, 12 5/32" short arm hex key 1 1/8" short arm hex key 1 1/2" Yellow flat washers 4 1/4-20unc 2 1/4" lg button head socket cap, SS 2 1/4 x 1'' fender washer ss 2 1/4" flat washers, zinc 8 TOOLS REQUIRED FOR SSEMLY Ensure that you have the following tools available before you begin the assembly of your DefenderCab kit. Note: ssembly requires an assistant. Phillips & Flat Screwdrivers Ratchet set, ¼, 3/8, ½ 5/32 llen Wrench Metric and standard socket set Compact drill/driver 1/4 drill bit Utility knife Utility Clamps or Locking Pliers Rubber Mallet ar Clamps Dremel tool or die grinder 4
5 Kit Installation 1. Windhield Panel Install I) Loosely install the (2) 1 ¾ rubberized clamps onto top rollcage at approximate locations shown (Fig.1). Ensure tabs on panel clamps are pointing towards the interior of the vehicle. (Optional wiper package shown) Fig V) Install the L-H Front Filler and the R-H Front Filler to the bottom front roll bar using (4) M12x1.5, 80mm flanged hex bolts black [], (12) ½ yellow flat washers [] and the (4) existing OEM nuts [C]. (fig.4) (Current front fillers have slotted holes) 2016 & Up These filler attache using the existing bolt. Only using (4) ½ yellow flat washers [] On the inside and OEM Nuts Fig.4 C 5
6 VI) Re-install windshield panel onto vehicle. Fasten panel with (2) #10-32unc 1 long button head socket cap [], (2) nylon lock nuts [] and (2) windshield spacers [C] (Fig.5) ensuring windshield panel sits firmly onto foam gasket strip. C Fig.5 VII) fter installing the windshield, fasten the windshield panel to the front fillers using (4) 5/16-18 x ¾ long flanged bolts [], (4) 5/16-18 heavy nyloc nut yellow zinc Plated [] and (4) washers i.d o.d. stainless steel [C] (fig.6) The windshield panel install is now complete. Fig.6 C Roof Trim Install V) Install a length of edge trim (5/8 bulb) along the roof side edges as shown, starting from the front working your way to the rear. (fig.12) Fig.12 6
7 Fig.13 VI) Cut the edge trim (5/8 bulb) at the desired length, ensuring you have it flush against the back panel (fig.13) ack Panel Installation Fig.14 First we need to prepare the side by side for the back panel. Remove both seat covers by unclipping the front and pulling upwards. Remove the 4 bolts holding seat down (fig.14). Once the seat is removed you may remove the side panel s inbetween the rear roll bar and dump box (fig.15). Turn clip seen in (fig.16) to remove this panel. Fig.15 Now we are ready to install the Rear Lower panel slide in the panel behind the cross roll bar and push the bottom of the panel until it hold on the floor lip (fig.17). Fig.16 Fig.17 7
8 Fig.18 Secure lower panel with Rear panel attachement brackets using 1/4-20unc 2 1/4" lg button head as shown in Fig. 18. dd trim to side of rear panel where it meets the rollbar. Next step is to put loosen the top OEM bolt from Cross roll bar and slide in our rear attachement brackets into slots and lining up with the panel. Using ¼ -20 1/2" lg button head, Washer.26" i.d.55" o.d Stainless steel and 1/4-20 Flanged lock nut. ttachethe rear upper side panels to the lower panel and attachement bracket.secure top of side panel using ¼ -20 1/2" lg button head with 1/4 x 1'' fender washer ss and 1/4-20 Flanged lock nut (fig. 21). Fig.18 The back upper back panel maybe be installed to the lower and side panels using (17) ¼ -20 1/2" lg button head and (17) ond seal galvanized washer. The rear upper panel can be pushed upward 8
9 Door Install (Front and Rear, Left and Right door installations will be the same. General door instructions will be detailed once.) Fig.14 I) Remove doors from factory mounting points by removing the original bolts (4 per door). (fig.14) Place doors on a workbench or table for ease of work. Defender Cab doors will be mounted on existing factory doors. II) Steadily line up face plate with the extrusion on the interior side of the door and mark the locations of the 8 holes. lso mark the triangle in the middle of the face plate. Drill each hole using a ¼ drill bit and cut out the center hole with a dremel tool or die grinder. e careful not to drill or cut too far as it is easy to go through both sides of the door or hit the inner latching mechanism. Fig.15 III) Insert (8) push type retainers, ¼, phillips, black [] in the holes to hold the face plate in place. (fig.15) 9
10 (Ignore the door lever in fig.15) IV) Tap in the (4) door bushings into the door hinge holes, (fig.16a) making them flush with the hole on the exterior side of the door. (fig.16b). Fig.16a Fig.16b V) Insert (4) washers i.d o.d. stainless steel [] (one per hole, fig.17a) and (4) 5/16-18 x 1 ¾ long hex cap screws [] (fig.17b) on the outer side of the door. Fig.17a Fig.17b VI) Take the door and place it on the factory hinges of the TV. (fig.18a) Then place (4) washers (0.406 i.d o.d. stainless steel) [] on the other side of the hinge (fig.18b). Fig.18a Fig.18b 10
11 Fig.19 VII) Tighten (4) reg hex nuts [] onto the 5/16-18 bolt from step VI then place (4) more washers (0.406 i.d o.d. stainless steel) [] on the other side of the nut. (fig.19) VIII) Slide the (4) knobs [] onto the (4) door levers []. Fig.20 On the lower door assembly, use the most rearward hole for the right hand side levers and use the forward hole for the left hand side levers (fig.20) for installation. Left lever s hole Right lever s hole D Install the door levers on the lower door frames bolted in this order: (1) ¼-20unc ¾ long button head socket cap [C], (1) 0.26 i.d o.d. SS washer [D], (1) lower door frame [E], (1) same size washer [D], (1) door lever [], (1) same size washer [D] and (1) ¼-20 nyloc nut [F]. Fig C E F
12 Fig.22 ll door levers are different for each corner. The figure below will show which lever goes to which corner. (fig.22) (Left levers are push to open while right levers are pull to open) IX) Install bumper to lower door frame where shown (fig.23a) using (1) M6x1.00, 8mm pan head Phillips screw [], (1) ¼ flat zinc washer [] and (1) door frame bumper [C] (fig.23b). Fig.23a C Fig.23b 12
13 X) Place the lower door frame assembly onto the door having the extended end of the door lever going into the door latch. (fig.24) Fig.24 XI) Place (4) i.d o.d. stainless steel washer [] onto the 5/16-18 bolts from step VI (fig.25a) then loosely place (4) 5/16-18 yellow zinc plated heavy nyloc nuts [] onto that same bolt. (fig.25b) Fig.25a Fig.25b XII) Place (2) M6x1.00, 16mm, pan head phillips screw, zinc plate [] and (2) ¼ zinc flat washers [] in the slots of the lower door frame assembly and lossely fasten into the door (fig.26). djust the lower door frame assembly the the desired position where the door can close with no interference (approx. middle of the slot). Tighten the screws from this step and the nuts from step X. lso adjust and tighten the door frame bumper from step IX to the desired height. 13 Fig.26
14 XIII) Place the upper door frame assembly on top of the lower door frame assembly ensuring the seal under the window is against the outside of the plastic door. Place and tighten (5) ¼-20 x ½ long button head socket cap screws [] and (5) 0.26i.d o.d. wahsers [] into the existing pem nuts to fasten the door assemblies together. (fig.27a). Fig.27a XIV) Insert (2) ¼-20 x ½ long button head socket cap screws [], (2) 0.26i.d o.d. wahsers [] and (2) ¼-20 flanged lock nuts [C] to serve as adjustment for the upper door frame s angle (fig27b). Tilt the upper door frame inward until the top of the door is tight against the roll bar when closed. Tighten when adjustment has been completed. Fig.27b C 14
15 XV) Install the door crossmember caps by placing them over the crossmembers (middle of lower door frame) using (6) #8 x ½ sheet metal screws, truss head, Phillips. [] (fig.28) Fig.28 This concludes the door installation. Repeat steps I through XV to complete each door. Using the 3 ack panel clips provided you may fasten the back panel to the roof. Using bondseal washers and 1/4x20 bolt and nut drill thru the roof and fasten to rear panel. 15
16 OPERTION The DefenderCab is very useful for work or play. It is perfect for the hunting, farming, fishing, commercial and recreational enthusiast. The cab and optional wipers allow the full enjoyment of the vehicle in all weather conditions. Cleaning your DefenderCab Use same mild soap and techniques used to clean your TV To order replacement parts, contact the Parts Department at: L Manufacturing Inc. 247 rsenault Road, Dieppe, N. Canada E1 7J5 Ph: (506) Fax (506) parts@defendercab.com Manual Revision: 1.0 Date: ugust 11,
Kawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions.
Owner s Manual Model: Kawasaki Teryx 750 Kawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Safety Instructions Cab Kit Contents Hardware
More informationHisun Deluxe Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Owner s Manual.
Owner s Manual Model: Hisun Hisun Deluxe Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Safety Instructions Cab kit Contents Hardware Assembly Panel Assembly
More informationRH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More informationINSTALLATION INSTRUCTIONS RH 412 STEEL DOORS
By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job
More informationBe sure any accessory used will fit with the soft upper doors before installing. Not all accessories will be compatible.
Company Name: Spike Power Sports Vehicle Name: Polaris General 2P Product Description: Soft Upper Doors Part Number: 58-1600 Revision: R01 09/19/2018 Contents: 655 Elm Ridge Ave, Canal Fulton OH, 44614
More informationRangerWare Fiberglass Door System Installation Instructions P/N
Page 1 of 9 RangerWare Fiberglass Door System Installation Instructions P/N 2878016 ORDER OF INSTALLATION Note: To assure proper order, read all Accessory Installation Instructions before beginning. 1.
More informationWARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. WARNING. Ranger XP Door Kit
REVISION 04 November, 20 2018 Ranger XP Door Kit Prior to installation, please verify if a revised version of this instruction sheet is available on Knowledge Center. The following symbols may be used
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationInstallation Instructions
For Medium (15-18.5K) + Heavy duty (22-28.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp
More informationWPS crew Doors Installation instructions
WPS-132-133 crew Doors Installation instructions ORDER OF INSTALLATION FOR A COMPLETE ENCLOSURE OF A CREW WPS (Weather Protection System) IS AS FOLLOWS: 1. Heater 2. Rear Thresholds - Right Hand & Left
More informationInstallation for Full Size Polaris Ranger Crew Doors
Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated
More informationRZR 4 Doors Part # Polaris RZR XP & Turbo ( ) Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com RZR 4 Doors Part # 07-1802 Polaris RZR XP 4 1000 & Turbo (2015-2018) Black Revision No: 01 Revision Date:
More informationInstallation Instructions
For Medium (15-18.5K) + Heavy duty (-8.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SNYPER TUBULAR FENDERS APPLICATION: 2007-2017 Jeep Wrangler JK PART NUMBER: 62-1005, 62-1015 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1,2 2 FRONT FENDERS, DRIVER (1) AND PASSENGER
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK001 / KRJW014T INSTALL TIME: 2.5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationREAD BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION
edium + Heavy duty READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Pay attention to danger and safety notices. be exposed: Carefully
More informationInstallation Instructions
edium + Heavy duty READ BEFORE INSTALLING UNIT Preliminary instructions: 1. Check window opening size: the mounting parts furnished with this air conditioner are made to install in a wooden sill double-hung
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationINSTALLATION & OWNER S MANUAL
Rev. O p. 1 of 16 INSTALLATION & OWNER S MANUAL V4213 BALL CAGE KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation
More informationINSTALLATION INSTRUCTIONS KK-K9-F14-K K9 KIT FOR FORD EXPEDITION
INSTALLATION INSTRUCTIONS KK-K9-F14-K-32 32 K9 KIT FOR 2003-2016 FORD EXPEDITION TOOLS REQUIRED: Power Drill Drill Bit Set Standard & Metric Socket Sets Phillips Screw Driver Open End Wrench Set Wire Cutters
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET
More informationInstallation Instructions
READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory FABRIC REAR DOORS (5P) P/N 0SR90-HL4-211B (BLACK) P/N 0SR90-HL4-211C (CAMO) Application SXS1000M5P/M5D Honda Dealer: Please give a copy of these instructions to your
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 645 For Chevrolet Silverado 500HD & 3500 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of looks,
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationINSTALLATION INSTRUCTIONS KK-K9-C12-K CHEVY IMPALA
INSTALLATION INSTRUCTIONS KK-K9-C12-K 2000-2005 CHEVY IMPALA READ ALL INSTRUCTIONS PRIOR TO INSTALLATION TOOLS REQUIRED: Power Drill Drill bits1/4 and 5/32 7/l6 wrench and socket 15,18 and\or 19mm socket
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS Toyota 4Runner
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2003-2009 Toyota 4Runner Please read before beginning Stainless steel hardware may bind
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK002 / KRJW014T INSTALL TIME: 5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationKawasaki Mule Pro Upper Doors #06020 Installation & Operations Manual
Kawasaki Mule Pro Upper Doors #06020 Installation & Operations Manual Before You Start: Please familiarize yourself with all the steps before beginning assembly. Compatibility Info: This Door System is
More informationAssembly Instructions 10 X 10 Aluminum Roof Support
Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1
More information4-Door EXO-Top Roof Rack System
Page 1/31 4-Door EXO-Top Roof Rack System 13516.02! WARNING The EXO-Top Roof Rack System is rated to a dynamic 300 lb, evenly distributed load. Further loading could result in serious injury or death.
More informationLAnd Rover defender TDI & TD5 Gullwing WINDOW Box. You will need to have installed a Gullwing Door before installing the Window Box.
LAnd Rover defender TDI & TD5 Gullwing WINDOW Box GWLD008 INSTALL TIME: 2 Hours You will need to have installed a Gullwing Door before installing the Window Box. IMPORTANT WARNING! IT IS CRITICAL THAT
More informationPro Ski / Snowboard & Fishing Rod Carrier
Pro Ski / Snowboard & Fishing Rod Carrier ENG RRAC123 10 min READ ME! Thank you for purchasing a Front Runner Pro Ski / Snowboard & Fishing Rod Carrier. Before you start, take a moment to familiarize yourself
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: GMC SIERRA 1500 HDX & SPORTSMAN GRILLE GUARDS (2014 & UP) APPLICATION PART # S 57-3690, 57-3695, 40-3695, 45-3690 ITEM QUANTITY
More informationJEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK004 / KRJW016T INSTALL TIME: 2 Hours NOTE: Your Jeep JK (3 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R5 STEP BOARD APPLICATION: 2009-2017 Dodge Ram 1500 Quad / Crew Cab 2010-2017 Dodge Ram 2500/3500 Crew Cab PART NUMBER: 28-51040, 28-51045, 28-51050, 28-51055 ITEM QUANTITY DESCRIPTION
More informationMedium HoneyBadger Chase Rack Installation Instructions
PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading
More informationPLOW MOUNT KIT FOR KAWASAKI TERYX, YAMAHA RHINO P/N ASSEMBLY / OWNERS MANUAL
PLOW MOUNT KIT FOR KAWASAKI TERYX, YAMAHA RHINO P/N 34-2025 ASSEMBLY / OWNERS MANUAL Application PLOW PUSH FRAME NO. 34-0000 or 34-0070 Before you begin, please read these instructions and check to be
More informationINSTALLATION INSTRUCTIONS, AND PARTS LIST
INSTALLATION INSTRUCTIONS, AND PARTS LIST LB20 SERIES RAMPS Link Mfg. Ltd. 223 15th St. N.E. Sioux Center, IA USA 51250-2120 (712) 722-4868 Fax (712) 722-4779 QUESTIONS? CALL CUSTOMER SERVICE 1-800-248-3057
More information55000/55010 Installation Instructions
A. Install 55015 B. Bolt roof rails, 55020/55025, to front hoop. C. Assemble 55026 D. To install without drilling into bumper. E. If mounting directly to bumper. A. 55015 Installation Instructions 55000/55010
More informationFranklin Mills Stackable Movable Lateral Instructions
Franklin Mills Stackable Movable Lateral Instructions Table of Contents: Table of contents...1 Tools Required...2 Stationary Shelving Assembly...3-7 Mobile Shelving Assembly...8-16 Rail Assembly...8-11
More informationASSEMBLY INSTRUCTIONS FOR STORETTE STA42
ASSEMBLY INSTRUCTIONS FOR STORETTE STA42 A01 CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces to avoid a mishap. For safety sake, please read the safety information
More informationINSTALLATION INSTRUCTIONS K9-C20-32 & K9-C CHEVROLET 4 DOOR TAHOE, GMC YUKON, SUBURBAN and YULON XL
INSTALLATION INSTRUCTIONS K9-C20-32 & K9-C21-32 2007-2014 CHEVROLET 4 DOOR TAHOE, GMC YUKON, SUBURBAN and YULON XL TOOLS REQUIRED: Power drill Drill bit set Standard & metric socket sets Phillips screwdriver
More informationGeneral Features. Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized
General Features Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized Two Sizes Short Box :74 L X 47 W X 7 T and Long Box 92 L X 47 W X 7 T All Aluminium
More informationINSTALLATION & OWNER S MANUAL
Rev. A, p. 1 of 28 INSTALLATION & OWNER S MANUAL KAWASAKI TERYX4 ClearView Cab p/n: 1KAWT8004CV This cab fits model years: 2014- The contents of this envelope are the property of the owner. Be sure to
More informationINSTALLATION INSTRUCTIONS 3 BULL BAR 99-04, 04 "HERITAGE" F-150/250LD 2WD, 97-04, 04 "HERITAGE" 4WD WD EXPEDITION/ WD EXPEDITION PART
INSTALLATION INSTRUCTIONS 3 BULL BAR PART #B-F1971;B-F2971 PARTS LIST: 1 Bull Bar 2 12-1.75mm x 130mm x 40mm Hex Bolts 1 Driver/Left Mounting Bracket 4 12-1.75mm x 35mm Hex Bolts 1 Passenger/Right Mounting
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 005-07 Cadillac STS Classic 3D Z, Classic Dual Weave, Classic Mesh & Classic Black Mesh Grilles B 7 HR 3 STS Classic 3D Z Grille Part
More informationINSTALLATION INSTRUCTIONS SIDE BAR FORD ESCAPE & MAZDA TRIBUTE PART #
INSTALLATION INSTRUCTIONS SIDE BAR 2008-2010 FORD ESCAPE & MAZDA TRIBUTE PART # 50136 50137 PARTS LIST: 1 Driver/Left Sidebar 2 10-1.50mm x 35mm Bolt Plate 1 Passenger/Right Sidebar 2 10-1.50mm x 30mm
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For Chevrolet Silverado 1500HD & 2500 Kit 68162 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of
More informationJEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK005 / KRJW016T INSTALL TIME: 5 Hours NOTE: Your Jeep JK (3 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationJEEP CARGO SLIDE IMPORTANT WARNING! SSST001. INSTALL TIME: 45 mins
JEEP CARGO SLIDE SSST001 INSTALL TIME: 45 mins IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
More information2-Door EXO-Top Roof Rack System
Page 1/29 Part 13516.01 2-Door EXO-Top Roof Rack System! WARNING The EXO-Top Roof Rack System is rated to a dynamic 300 lb, evenly distributed load. Further loading could result in serious injury or death.
More informationLEGENDS RETRACTABLE DOOR SCREENS
LEGENDS RETRACTABLE DOOR SCREENS MAGNETIC LATCHING DESIGN SYSTEM 42 I N S T A L L A T I O N I N S T R U C T I O N S 1 MOUNTING OPTIONS Recess : Mount the Screen Cassette using Recess Mounting Clips Recess
More informationUNIVERSAL SPADE BRACKET RATCHET TYPE
UNIVERSAL SPADE BRACKET RATCHET TYPE RRAC024 INSTALL TIME: 15 mins IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER
More information6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME SPIRIT/LASER LEVEL TO LEVEL THE UNIT
1 TOOLS REQUIRED: MOVING CART/DOLLY FOR TRANSPORTING PANELS, ROOF, AND POSTS TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELS MINI REVERSIBLE RATCHET 1/4 DRIVE FOR CORNER SCREWS ON TOP TRAVERSE BEAMS
More informationTIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together
More information4 BAY Low Profile WALL MOUNT CABINET
D1/347 SSEMLY INSTRUCTIONS 4 Y Low Profile WLL MOUNT CINET TIP HZRD WRNING! Cabinet must be affixed to wall. For use to prevent tipping in compliance with capacity of cabinet specified. Use with heavier
More information** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at:
3/01/2007 VISIT THE LITIME WEB SITE: WWW.LITIME.COM ** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at: 1 (800) 225-3865 Double Shed Doors for Back
More informationDRAWER Mitsubishi pajero lwb
DRAWER Mitsubishi pajero lwb SSDS601 / SSMP001 INSTALL TIME: 45 mins Thank you for purchasing a Front Runner Storage System. This Storage System is made up of the following components: 1. A Drawer System
More informationFord F150 Front Bumper
2009-2011 Ford F150 Front Bumper Warning! Read the instructions completely before beginning the installation. Before tightening bolts, drilling or cutting where required, check to make sure that there
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationIntercooler Shroud and Belt Cover for WRX
Intercooler Shroud and Belt Cover for 2015+ WRX 2016-05-18 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation
More informationLinear Hook- on Worksurfaces
Linear Hook- on Worksurfaces Linear Hook-On Worksurfaces come in three depths and seven lengths. Different worksurfaces have different reqirements for installation that are outlined below. 27 inch deep
More information3 BAY AV CREDENZA WITH SINGLE DISPLAY MOUNT
D2/337M1 SSEMLY INSTRUCTIONS 3 Y V CREDENZ WITH SINGLE DISPLY MOUNT TIP HZRD WRNING! For use with video monitors weighing 175lbs (80kg) or less. Use with heavier televisions may result in instability causing
More informationLED 40" LIGHT BAR BRACKETs
LED 40" LIGHT BAR BRACKETs RRAC099/RRAC101 If you would like to mount your Light Bar under your Rack, refer to Sections 3 and 4. You will need a minimum of 100 mm clearance between the bottom of the Rack
More informationD. Drill Bolt Holes Through Topper Shell and Bed Rails
A. Check Mounting Kit Check to make sure that all of the following items are included in the mounting kit. Call 515-272-4372 if you need to obtain a part from BrandFX. Double-stick tape (1 roll) White
More informationTITAN2-EDGE Public Access Computer Station Dual Track
TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the
More informationF l a t S c r e e n A R M S I n s t a l l a t i o n
ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)
More informationWarnings. Description. Prior to Installation Tools Needed
Warnings Failure to act in accordance with the following may result in death or personal injury. The JT Strong Arm Stabilizer System is intended to eliminate chassis movement in travel trailers and fifth
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationRear Mount Installation Instructions
Rear Mount Installation Instructions Ford Transit Low Roof 130 WB Frame Kit Part #: DTC 0809-011 V1.0.10.12.18 IMPORTANT INSTALLATION STEPS ARE DENOTED USING A STOP SIGN. THESE STEPS MUST BE PERFORMED
More information3/4 Rear DuraRac Installation Instructions
3/4 Rear DuraRac Installation Instructions Ford Transit Low Roof 130 WB Frame Kit Part #: CRC 27-1010-001 V1.0.09.28.18 IMPORTANT INSTALLATION STEPS ARE DENOTED USING A STOP SIGN. THESE STEPS MUST BE PERFORMED
More information(2) Plastic Plugs (2) Frame Bracket. Spacers. License Plate Bracket. (2) 12mm Single Bolt Plates. (2) 12mm Double Bolt Plates
LDB-CSIL26-FB PARTS LIST: 1 LD1 Bumper Assembly 10 12mm Hex Nuts 1 Driver/left Frame Mounting 6 10-1.5mm x 35mm Hex Bolts 1 Passenger/right Frame Mounting 12 10mm x 27mm OD x 3mm Flat Washers 2 Spacers
More informationS H E D A S S E M B L Y I N S T R U C T I O N S
T I T A N R A N G E S H E D A S S E M B L Y I N S T R U C T I O N S 8 X 10 ft Approx = 2550 x 3140 cm COMPONENT LIST Component illustrations are given as a visual guide only and are not in proportion PART
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationDriver/Left Top. Support Bracket
PARTS LIST: 1 Grille Guard 8 10mm Lock Washers 1 Driver/Left Frame Bracket 8 10mm Hex Nuts 1 Passenger/Right Frame Bracket 2 8-1.25mm x 25mm Button Head Bolts 1 Driver/Left Bottom Support Bracket 2 8mm
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationEquilibrium. Conference Table. Installation Instruction. Revision B 11/07/16
Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationGeneral Prisoner Transport Install Instructions PT-2-INST
General Prisoner Transport Install Instructions PT-2-INST 50 or 60 high x 80, 100 & 120 inch long / Double Compartment Inserts Also refer to PT-A-3XX instructions for vehicle specific mounting measurements
More informationTHANK YOU FOR PURCHASING THE M/T METAL SERIES MODULAR JK FRONT BUMPER
THANK YOU FOR PURCHASING THE M/T METAL SERIES MODULAR JK FRONT BUMPER Your safety and the safety of others is very important. Please read and understand all safety precautions before installing this or
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More information6 BAY AV CREDENZA WITH DUAL DISPLAY MOUNT
D2/367M2 SSEMLY INSTRUCTIONS 6 Y V CREDENZ WITH DUL DISPLY MOUNT TIP HZRD WRNING! For use with video monitors weighing 175lbs (80kg) or less. Use with heavier televisions may result in instability causing
More informationParts and tools needed for installation- Cleaning and Painting -
Thank you for the purchase of our JK Rear Trail Doors. We have made these from 6061-T6 aluminum and reinforced them with stiffeners at the top that double as a comfortable armrest and support for Rugged
More informationTHIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE
Sal es@lambodoorscanada. com 2407A Kal adarave,ottawa,on K1V 8B9 THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE 2 SHOCKS 565 PSI 2 SHOULDER
More informationINSTALLATION INSTRUCTIONS
NOTE: Bolts should remain hand tight until all bolts are installed. STEP 1 Installing the door base (both sides). 1. Locate the outer, roll cage, mounting bolt (passenger side is shown in the illustration).
More informationVIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4
PARTS LIST: VIEWPOINT ALUMINUM RUNNING BOARD 1 Driver/Left Running Board 4 10-1.5mm x 50mm T-Bolt 1 Passenger/Right Running Board 12 10mm Plastic Retainers 1 Driver/Left Bracket 2 10-1.50mm x 40mm Hex
More informationCORVETTE CORVETTE REV: Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending.
CORVETTE 2005-2006 CORVETTE 2005-2007 REV: 7-2-07 Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending. Page 1 of 12 CORVETTE C6 2005-2007 THIS KIT INCLUDES:
More informationJK Front Crusher Flares
INSTALLATION INSTRUCTIONS INST-17-03-030_A JK Front Crusher Flares IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationEnclosed Partition Installation Instructions
Nissan NV1500/2500/3500 High Roof Partition Kit Part #: DTC 1502-036 V1.0.08.06.18 IMPORTANT INSTALLATION STEPS ARE DENOTED USING A STOP SIGN. THESE STEPS MUST BE PERFORMED IN THE SPECIFIED ORDER TO ENSURE
More informationInstallation Guide 40670
Installation Guide 40670 Kargo Master Rancho Cordova, CA 95742 800-343-7486 CustomerService@KargoMaster.com DATE: Installation Instructions 40670 *PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING,
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Serial Number BX3620 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue
More informationRAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED
RAMPAGE P R O D U C T S 84 (+/- 1/4 ) INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO 1966-1977 TOOLS REQUIRED 3/8 WRENCH 7/16 WRENCH ½ WRENCH #2 PHILLIPS SCREWDRIVER 1/8 DRILL
More informationTABLE MKI small with Basin and under rack brackets kit
TABLE MKI small with Basin and under rack brackets kit TBRA024 INSTALL TIME: 15 mins IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO
More informationInstallation Instructions Kit, Base Rail Bracket Part # 31413
Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating and
More informationWARNING. Bolt Torque Specifications Torque in Foot-Pounds for Inch Bolts Bolt Size Grade 5 Grade 8
1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar with our products and have the equipment and knowledge necessary to do fit work. If needed, Blue
More informationINSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: ,
INSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: 2010-2014 CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: 32-21020, 32-21025 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 CONTOUR BAR TORQUE WRENCH 2 1
More informationPH03 Comfort XL Front Assembly Replacement Instructions
PH03 Comfort XL Front Assembly Replacement Instructions POLYJOHN USA PolyJohn Enterprises Corp 2500 Gaspar Ave. Whiting, IN 46394 Phone: 800-292-1305 Fax: 219-659-0625 www.polyjohn.com info@polyjohn.com
More informationTOYOTA TACOMA LED BED LIGHTS Preparation
Preparation Part Number: PT948-35160 Kit Contents Item # Quantity Reqd. Description 1 1 Hardware Kit 2 1 Driver Side LED assembly 3 1 Passenger Side LED assembly 4 1 Main Wire Harness Hardware Bag Contents
More informationINSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only)
INSTALLATION MANUAL FRONT Level of Difficulty Moderate Product Photo (center section only) All hardware listed below will be provided with the bumpers center section. Additional hardware will be supplied
More information