Assembly Instructions

Size: px

Start display at page:

Download "Assembly Instructions"

Gary Freeman
5 years ago
Views:

1 Assembly Instructions VESA Flex Flip Lounge 1.

2 Contents VESA Flex Flip Lounge p.3-18 p p p

3 Assembly Instructions VESA 3.

4 What's in the Box Case Washer x1 T20 Driver Bit x1 M4 Split Washer x4 M4 20mm Buttonhead Screw x4 VESA Mount no.8 x 38mm Countersunk Screw x4 4.

5 This Tablet Configured for Attach case to mounting arm with hand operated screwdriver only. If you would like to use a different tablet in this case, please contact us for a conversion kit. What's in the Box Tablet Setup Kit Keys x2 Tablet Support x4 Corner Pieces x4 Cable Clip x1 Sticker x1 Faceplate x1 Case x1 5.

6 Tools for the Job Pencil 16mm or 41/64" Drill Bit Hand Drill Socket Screwdriver 2mm or 5/64" Drill Bit 6.

7 Recommended Installation Height Avoid Glare Don't install directly beneath a light source 155cm / 5' 7.

8 Mark the Drill Holes Mark all four outer holes and the large central hole IMPORTANT: Make sure the Lock will still be accessible once the case is installed Pencil VESA Mount 8.

9 Choose Cable Routing Method Through Surface -Hidden Cabling -Requires access to back of the Wall On Surface -Visible Cabling -Perfect for Solid Walls 9.

10 Drill the Holes IMPORTANT: 2mm / 5/64" holes are designed for supplied woodscrews. If using your own screws eg when attaching to brick a different hole size may be needed 2mm 5/64" 2mm 5/64" NOTE: The 16mm / 41/64" hole is only required for 'On Surface' Mounting 16mm 41/64" 2mm 5/64" Scale 1:1 2mm 5/64" 10.

11 Attach to Surface IMPORTANT: If you have chosen 'On Surface' cable routing, the cable must be routed through cable channel before screwing to surface No.8 38mm Countersunk Screws VESA Mount 'On Surface' Cable Channel 11.

12 Attach Case M4 20mm Buttonhead Screws M4 Split Washers Case Washer 12.

13 Route Cable Use the adhesive cable clip to secure cable in the nearest quadrant to the Tablet Power Port Cable Clip 13.

14 Case Setup Cornerpieces Sticker Tablet Supports 14.

15 Insert Tablet NOTE: Ensure Tablet is connected to Power Cable 15.

16 Lock Up Faceplate Case 3. Turn Key to Lock 16.

17 VESA Compatibility The Bouncepad VESA mount can also be screwed to VESA arms (fixings not supplied) 17.

18 Your Bouncepad is now installed For further information and support please contact us: UK & International +44 (0) Deutschland +49 (0) USA & Canada

19 Assembly Instructions Flex 19.

20 What's in the Box M4 16mm Buttonhead Screw x4 M4 Wingnut x4 Case Washer x1 Through Mounting Washer x1 M4 10mm Countersunk Screw x4 T20 Driver Bit x1 M4 Split Washer x8 M4 Hex Nut x4 No.8 38mm Countersunk Screw x4 M4 40mm Socket Setscrew x4 Flex Stalk Surface Mounting Plate x1 Surface Mounting Plate Cover x1 20.

21 This Tablet Configured for Attach case to mounting arm with hand operated screwdriver only. If you would like to use a different tablet in this case, please contact us for a conversion kit. What's in the Box Tablet Setup Kit Keys x2 Tablet Support x4 Corner Pieces x4 Cable Clip x1 Sticker x1 Faceplate x1 Case x1 21.

22 Tools for the Job 5mm or 13/64" Drill Bit 2mm or 5/64" Drill Bit Pencil 16mm or 41/64" Drill Bit Hand Drill Socket Screwdriver 7mm Spanner or 9/32" Wrench 22.

23 Recommended Installation Height No Wallmount Avoid Glare Don't install directly beneath a light source 90cm / 35'' 23.

24 Choose Mounting Options Through Mount Surface Mount up to 25mm / 1" Any thickness above 25mm / 1" -Seemless appearance -Requires access beneath mounting surface -Option to route cable along surface when there is no access beneath mounting surface Continue to p.25 Continue to p

25 Through Mount Step 1 of 4 Step 2 of 4 Mark the Drill Holes Drill the Holes This diagram can be used as a drill template Through Mounting Washer Pencil 5mm 13/64" 16mm 41/64" 5mm 13/64" 5mm 13/64" Front 5mm 13/64" Scale 1:1 25.

26 Through Mount Step 3 of 4 Screw in socket setscrews by hand M4 40mm Socket Setscrew 26.

27 Through Mount Step 4 of 4 Fasten from beneath surface Through Mounting Washer M4 Split Washer x4 M4 Hex Nut/Wingnut x4 7mm Spanner / 9/32" Wrench Wingnuts Hex Nuts Now Skip to p.31 Quick Assembly High Security 27.

28 Surface Mount Step 1 of 4 Mark the Drill Holes Pencil Surface Mounting Plate Front 28.

29 Surface Mount Step 2 of 4 Drill the Holes This diagram can be used as a drill template 2mm 5/64" 2mm 5/64" IMPORTANT: 2mm / 5/64" holes are designed for supplied woodscrews. If using your own screws eg when attaching to brick a different hole size may be needed 16mm 41/64" NOTE: The 16mm / 41/64" hole is not required if attaching to surface with no access beneath as the power cable can be routed along the surface 2mm 5/64" Scale 1:1 2mm 5/64" 29.

30 Surface Mount Step 3 of 4 Attach mount plate 1. Screw Mount plate onto Stalk 2. OPTIONAL Route power cable down the Stalk and through cable channel (only applicable if you choose to route cable along surface) Cable Channel Surface Mounting Plate Cover Sticky Tabs Surface Mounting Plate M4 10mm Countersunk Screws 30.

31 Surface Mount Step 4 of 4 Attach to Surface 1. Screw Mounting Plate to surface 2. Remove backing from sticky Tabs 3. Slide Surface Mounting Plate Cover onto Stalk 4. Push down firmly on Mounting Plate Cover Surface Mounting Plate Cover No.8 38mm Countersunk Screws Surface Mounting Plate 31.

32 Attach Case M4 16mm Buttonhead Screws M4 Split Washers Case Washer 32.

33 Route Cable Use the adhesive cable clip to secure cable in the nearest quadrant to the Tablet Power Port Cable Clip 33.

34 Case Setup Cornerpieces Sticker Tablet Supports 34.

35 Insert Tablet NOTE: Ensure Tablet is connected to Power Cable 35.

36 Lock Up Faceplate Case 3. Turn Key to Lock 36.

37 Your Bouncepad is now installed For further information and support please contact us: UK & International +44 (0) Deutschland +49 (0) USA & Canada

38 Assembly Instructions Flip 38.

39 Tools for the Job Socket Screwdriver What s in the Box Flip Base Key T20 Driver Bit x1 M4 20mm Buttonhead Screw x4 M4 Split Washer x4 Flip Endplates x2 Flip Base x1 Case Washer x1 39.

40 This Tablet Configured for Attach case to mounting arm with hand operated screwdriver only. If you would like to use a different tablet in this case, please contact us for a conversion kit. What's in the Box Tablet Setup Kit Keys x2 Tablet Support x4 Corner Pieces x4 Cable Clip x1 Sticker x1 Faceplate x1 Case x1 40.

41 Attach Case Cable Clip M4 20mm Buttonhead Screws M4 Split Washer Case Washer Case Flip Base Use the adhesive cable clip to secure cable in the nearest quadrant to the Tablet Power Port Cable Clip 41.

42 Case Setup Route Cabling Corner Pieces Tablet Supports Sticker 42.

43 Insert Tablet NOTE: Ensure Tablet is connected to Power Cable 43.

44 Lock Up 2. Faceplate Case Turn Key to Lock 44.

45 Power Fit Endplates Connect cable to power supply OR NOTE: Ensure cabling exits correctly through cable notch in the Endplate Use the Flip enclosure to hold a portable battery 45.

46 Removing Endplates If the endplates need to be removed, insert the Flip Base Key into the cable notch and pull 46.

47 Surface Mount The Flip can be surface mounted using the four M6 holes found on the Base NOTE: Fixings are not supplied for surface mounting the Flip 47.

48 Your Bouncepad is now installed For further information and support please contact us: UK & International +44 (0) Deutschland +49 (0) USA & Canada

49 Assembly Instructions Lounge 49.

50 Tools for the Job Socket Screwdriver What s in the Box T20 Driver Bit x1 M4 Split Washer x2 M4 20mm Buttonhead Screw x2 Case Washer x1 Lounge Cone Assembly x 1 50.

51 This Tablet Configured for Attach case to mounting arm with hand operated screwdriver only. If you would like to use a different tablet in this case, please contact us for a conversion kit. What's in the Box Tablet Setup Kit Keys x2 Tablet Support x4 Corner Pieces x4 Cable Clip x1 Sticker x1 Faceplate x1 Case x1 51.

52 Attach Case Ensure Security Connector is Screwed into Case M4 Split Washers M4 20mm Buttonhead Screws Security Connector Case Washer NOTE: Lounge Cone is orientated with the cable pointing up 52.

53 Cable Clip Use the adhesive cable clip to secure cable in the nearest quadrant to the Tablet Power Port Cable Clip 53.

54 Case Setup Corner Pieces Sticker Tablet Supports 54.

55 Insert Tablet NOTE: Ensure Tablet is connected to Power Cable 55.

56 Lock Up Faceplate Case 3. Turn Key to Lock 56.

57 Tethering NOTE: The tethering loop can be used with a padlock to secure your bouncepad to the furniture 57.

58 Your Bouncepad is now installed For further information and support please contact us: UK & International +44 (0) Deutschland +49 (0) USA & Canada

60 Contact Details UK & International +44 (0) Deutschland +49 (0) USA & Canada

ASSEMBLY AND ADJUSTMENT

EDGE MONITOR ARM EDGE Rev A 2/17 Model EDGE-SLV Model EDGE-BLK Model EDGE-WHT ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and