MLM 226 Faceplates Installation Guide

Transcription

1 MLM 226 Faceplates Installation Guide MLM 226 Faceplates This guide provides instructions for installing the following Extron MediaLink Mounting Options faceplates, which are designed for use with the MLC 226 IP MediaLink Controller. The MLM 226 L, MLM 226 3GWP, or MLM 226 5GWP faceplate is shipped with the MLC 226 IP controller, depending on the controller configuration that is ordered. The rest of the mounting options described below may be ordered separately as replacements, or for use with an MLC 226 IP that is ordered without a faceplate. MLM 226 L A low-profile, 3.15" H x 6.50" W (8.0 cm H x 16.5 cm W) lectern/ furniture-mounting faceplate. This faceplate is required when you are mounting an MLC 226 IP using an optional UCM RAAP or UCM 10X8P mounting kit. Part numbers: (black), (white), (RAL9010 white) MLM 226 LAAP A low-profile, 3.15" H x 10.00" W (8.0 cm H x cm W) lectern/furniture-mounting faceplate with an opening that accommodates four single-space AAPs Part numbers: (black), (white), (RAL9010 white) MLM 226 3GWP A three-gang (4.50" H x 6.40" W [11.43 cm H x cm W]) faceplate that can be mounted to a mud ring (mounting bracket), an Extron Surface Mount Box, an Extron External Wall Box, or a standard electrical box Part numbers: (black), (white), (RAL9010 white) , Rev. D

2 MLM 226 Faceplates Installation Guide, cont d MLM 226 5GWP A five-gang (4.50" H x 10.04" W [11.43 cm H x cm W]) faceplate with an opening that accommodates four single-space AAPs. It can be mounted to a mud ring, an Extron Surface Mount Box, an Extron External Wall Box, or a standard electrical box. Part numbers: (black), (white), (RAL9010 white) MLM 226 7GWP A seven-gang (4.50" H x " W [11.43 cm H x cm W]) faceplate with two openings that accommodate four singlespace AAPs each (eight AAPs total). It can be mounted to a mud ring, an Extron Surface Mount Box, an Extron External Wall Box, or a standard electrical box. Part numbers: (black), (white), (RAL9010 white) Replacing an MLC 226 IP Faceplate with an MLM Faceplate 1. If your MLC controller is already installed in a wall or furniture, remove the four screws that attach it to its mounting surface (marked a in the diagram on the next page), and lift it out. 2. After the MLC has been removed from the wall or furniture, use a small Phillips screwdriver to remove the four faceplate attachment screws (b in the diagram on the next page), and save them for later use. CAUTION Do not remove the four faceplate screws while the MLC is installed in a wall or furniture, or the controller may fall down into the wall or furniture. 2

3 1 1 2 DISPLAY 2 ON OFF PIC MUTE VCR DVD VOLUME AUTO IMAGE DOC CAM LAPTOP PC 2 IR CONFIG 2 Extron MLC 226 IP Lift the faceplate off the MLC 226 IP, as shown below. ON OFF PIC MUTE VCR DVD DOC CAM LAPTOP PC AUTO IMAGE DISPLAY VOLUME IR CONFIG MLC 226 IP Extron 4. Align the openings in the new MLM faceplate with the controller s buttons, knob, and LEDs, then place the new faceplate on the MLC 226 IP. 5. Replace the four screws removed in step 2, and hand tighten them. 6. Install the MLC 226 IP controller with the MLM 226 faceplate in a wall or furniture as appropriate. 3

4 MLM 226 Faceplates Installation Guide, cont d Templates Use one of the following templates as a guide to measure and mark the hole for installing the MLM 226 faceplate with an attached MLC 226 IP. (Refer to your MLC 226 IP user s manual for instructions on preparing the mounting site.) CAUTION These templates are not to scale. Use the dimensions shown in the templates as reference guidelines for measuring and drawing the rectangle that will be cut out. The MLC controller requires a depth of at least 2.0" (5.1 cm) inside the wall or furniture. MLM 226 L and MLC 226 IP L template 3.15" (8.0 cm).250" (4 places) (0.64 cm) 6.5" (16.5 cm) 5.4" (13.7 cm) SURFACE CUT-OUT AREA FOR FURNITURE MOUNT and MLM 226 L.295" (4 places) (0.75 cm) Cut-Out Template for Extron's MLM 226 L and MLC 226 IP L 4

5 MLM 226 LAAP template 3.15" (8.0 cm) 8.9" (22.6 cm) 10" (25.4 cm) SURFACE CUT-OUT AREA FOR FURNITURE MOUNT and MLM 226 LAAP.250" (0.64 cm).295" (0.75 cm) Cut-Out Template for Extron's MLM 226 LAAP 5

6 MLM 226 Faceplates Installation Guide, cont d MLM 226 3GWP and MLC 226 IP template 4.5" (11.4 cm) 6.4" (16.26 cm) 5.4" (13.7 cm) SURFACE CUT-OUT AREA FOR FURNITURE MOUNT and MLM 226 3GWP Cut-Out Template for Extron's MLM 226 3GWP and MLC 226 IP 6

7 MLM 226 5GWP and MLC 226 IP AAP template 4.5" (11.4 cm) 8.9" (22.6 cm) 10.04" (25.5 cm) SURFACE CUT-OUT AREA FOR FURNITURE MOUNT and MLM 226 5GWP Cut-Out Template for Extron's MLM 226 5GWP and MLC 226 IP AAP 7

8 MLM 226 Faceplates Installation Guide, cont d MLM 226 7GWP template 4.5" (11.4 cm) " (34.71 cm) 12.7" (32.3 cm) SURFACE CUT-OUT AREA FOR FURNITURE MOUNT and MLM 226 7GWP Cut-Out Template for Extron's MLM 226 7GWP Extron Electronics, USA 1230 South Lewis Street Anaheim, CA FAX Extron Electronics, Europe Beeldschermweg 6C 3821 AH Amersfoort, The Netherlands FAX Extron Electronics, Asia 135 Joo Seng Rd. #04-01 PM Industrial Bldg., Singapore FAX Extron Electronics, Japan Kyodo Building, 16 Ichibancho Chiyoda-ku, Tokyo Japan FAX Extron Electronics. All rights reserved.