INDECO TECHNICAL CATALOGUE 2014

Transcription

1 INDECO TECHNICAL CATALOGUE 0 as at October 0 PN-EN 7:000 ITB AT--790/009

2

3 Contents S00 - SERIES SLIDING DOORS (steel system))... S00 - SERIES SLIDING DOORS (steel system)... S00 - SERIES PIVOTED DOORS (steel system)...9 A00 - SERIES SLIDING DOORS (aluminium system)... ONTARIO - FRAMELESS DOORS (aluminium system)... ATHABASCA - NARROW FRAME DOOR (aluminium system)... A00 - SERIES SLIDING DOORS (aluminium system)... A00 - SERIES SLIDING DOORS (aluminium system)... A00 - SERIES PIVOTED DOORS (aluminium system)...7 A00 - SERIES FOLDING DOORS (aluminium system)...79 INDECO TOOLS AND ACCESSORIES... INDECO PROFILES...90 Aluminium Profile Colour Range...9 Steel Profile Colour Range...9 Sales Support Tools...9 Orders...9

4 Types of INDECO Door Systems Bottom Roller Sliding Doors - Convenient access to the closet/wardrobe - A wide range of designs - Any front width, any number of door leaves - All leaves can be slid to one side in a multiple-track system Bottom Roller Slant Sliding Doors - Full use of space in rooms with lowered, slant ceilings (attics, lofts) - Doors fitted to slant walls Top Roller Sliding Doors - Suspended doors without the bottom track - Can also be used as pocket doors - Any front width, any number of door leaves - Excellent both for very wide and for very narrow doors - Can be easily trimmed at the bottom Top and Bottom Roller Sliding Doors - The highest strength and durability - The door can be trimmed at the bottom - The door can be out-of-plumb - Special decorative effects can be obtained, such as inclined doors Walk-through Sliding Doors without Thresholds - Full access to a walk-in closet - Can be used as pocket doors - No threshold Pivoted Doors - Single and double, left-hand and right-hand doors - Access to the entire wardrobe content - A good solution for narrow doors Folding Doors without Thresholds - Full access to the entire wardrobe content - Large wardrobe widths possible - Need half the space to open compared to pivoted doors with the same wardrobe width - No threshold

5 INDECO S00 SERIES STEEL SYSTEM bottom roller sliding doors Boundary conditions: - maximum dimensions of the opening: 00 mm in height; any width with sections of up to 000 mm each. - maximum dimensions of individual doors: 70 mm in height, 00 mm in width or, for light doors not exceeding 0 kg, the door width can be increased to 000 mm. - maximum weight of 0 kg. - panel thickness of mm and 0 mm.

6 INDECO S00 SERIES STEEL SYSTEM bottom roller sliding doors Components Assembly drawing xx 000xx 0000xx 0700yyxx 000yyxx 00yyxx PLS Bottom Roller Twin Wheel Top Guide Steel Double Bottom Track Steel Double Top Track Steel Rail Steel Stile Steel Stile Top Positioner Positioner, grey plastic xx xx xx 0000xx A 0000xx 099 Buffer Strip 099X Dust Stop Brush Strip Bottom Roller Guard left/right Steel Connector Rail 0// Spacer 0//0 Spacer Stick-on Decorative Strip Safety Backing Buffer Strip Clip Buffer Strip Clip Steel System Soft Closer Accessories Universal Soft Closer

7 INDECO S00 SERIES STEEL SYSTEM bottom roller sliding doors Fabrication instructions Calculate door front dimensions In your calculations, use the smallest dimensions of the opening to be fitted with sliding doors. Features such as lowered ceiling, floor batten or skirting boards reduce the dimensions of the door front. The door opening must be plumb and square. Where buffer strips are used, the width of the opening has to be reduced by 0 mm. OW opening width including buffer strips, OH opening height Advice: For an uneven opening, take measurements at several points and use the minimum dimensions in your calculations. Define the number of overlaps Overlaps are the places where door leaves overlap. Their number depends on how door leaves are positioned. If door leaves follow an alternating pattern, the number of overlaps equals the number of leaves less. In a staggered pattern, the number of overlaps will be smaller. n = number of leaves, z number of overlaps profile Calculate door leaf dimensions Overlap width = 0 mm Door leaf width: OW + z*0 mm DW = n Door leaf height: DH = OH mm DH = OH 7mm with soft closers profile Calculate door leaf dimensions Overlap width = mm Door leaf width: OW + z * mm DW= n Door leaf height: DH = OH mm DH = OH 7 mm with soft closer Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width (board or mirror) PW = DW mm Panel length (board or mirror) PL = DW mm Stile length: SL = DH Rail length: RL = DW mm for board RL = DW 0 mm for mirror Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width (board or mirror) PW = DW 9 mm Panel length (board or mirror) PL = DW mm Stile length: SL = DH Rail length: RL = DW mm for board RL = DW 7 mm for mirror Advice: For uneven door leaf widths, adjust the above calculations so that where the central door leaf is wider, the other leaves are narrower (by half of the difference each for a three-leaf door system). DW PW OH n= z= DH PL SL OW n= z= RL

8 INDECO S00 SERIES STEEL SYSTEM bottom roller sliding doors Fabrication instructions 7 Mirror protection Use colour and/or clear safety (laminated) glass. When using a mirror, fix safety backing 0000or 0000 to the back of the mirror, so that the backing strips overlap. Having fixed the backing, expel air bubbles using a brush or roller. Advice: For full safety make sure that mirror edges are ground smooth with abrasive paper in order to reduce internal stress. Combination panels When making a combination panel, connect it by means of a connector before you assemble the stiles (vertical profiles). To install glazed panels, tap the spacer 099 onto the panel. To combine a glass panel with a board, set the glass panel in the stile by tapping the spacer 0990 onto it. Install stiles Before assembly, cut installation openings at both ends of the stiles using the notching tool or the automatic notching tool Put one end of the stile against the corresponding end of the panel and tap the stile in place using a rubber mallet along the entire length, so that it protrudes. mm at both ends of the panel. Fix the other stile likewise. Advice: For a mirror, exercise special care when you start fixing the stile. Tap the stile carefully in position on the panel. Do not remove the protective backing from the stile when fitting the door at the customer s place. Tap stiles and spacers onto panels Tap stiles and spacers onto panels as per the drawings. To set glass panels in 0 mm profiles use the spacer Install rails Before assembly, cut installation holes at both ends of the rails using the universal notching tool Put one end of the rail against the stile. Using a rubber mallet, tap the rail in place along the entire length. Fix the other rail likewise. Advice: Owing to panel (mirror, glass or laminated board) cutting tolerances, panel dimensions may differ slightly from the desired ones. To avoid problems, before cutting the rails, measure the distance between the stiles and cut the rails to that length. Take care not to cause the stile ends to flare out when tapping the rail into place. 0 7, 9

9 INDECO S00 SERIES STEEL SYSTEM bottom roller sliding doors Fabrication instructions 0 Fix bottom rollers and top guides Slip guide tongues into the openings in the rail and then, turning the roller gently, push it so the catch snaps into the notch in the stile. Fix the other guides in the same manner. Advice: To protect the anti-jump feature against damage or breaking, the bottom roller wheel should be fully recessed into the roller body during transport. Structural reinforcement In order to reinforce the door leaf structure, you can optionally fix the rollers and guides to the profiles using. x 9. self-tapping screws Use two screws to fix the roller to the stile, driving them through the holes in the eyes abutting the stile. Then fix the tongue abutting the rail, driving one screw through one of the two holes. Fix the other rollers in the same manner. Advice: When fixing the rollers to the rails on glazed doors, exercise special care to avoid glass damage within the rail. Always use a power screwdriver to fix self-tapping screws. Note Fix buffer strips and dust-stop brush strips only after door installation has been completed. The entire glass surface (mirror, stained glass) should be secured with safety backing in compliance with the applicable laws and regulations. Only laminated safety glass can be used for clear-glass panelling. In order to reduce the risk of glass cracking as a result of stress produced during cutting, make sure that glass edges are ground smooth with abrasive paper or stone. Installation of the soft closer with a mm rail. Before fixing the rail, put one adapter against the rail, mark the positions of rivet holes, and then drill. mm rivet holes.. Rivet one adapter to the rail.. Then mount the soft closer onto the adapter, put the other adapter in place, mark the positions of rivet holes, and then drill. mm rivet holes.. Rivet the other adapter.. Fasten the soft closer to the adapters with screws.. Mount the rail with soft closer to the door leaf. 7. Measure the distance between the door edge and the adapter ( X ). 7 0 fixing screws

10 INDECO S00 SERIES STEEL SYSTEM bottom roller sliding doors Fabrication instructions Installation of the soft closer with a 0mm rail. Having fixed the rail, put one adapter against the rail and mark the position of the mounting screw hole.. Drill a.mm hole in the rail for the mounting screw and mount the adapter onto the rail.. Then mount the soft closer onto the adapter, put the other adapter in place and mark its position.. Remove the soft closer, put the adapter in the marked place and set the position of the mounting screw hole.. Drill a.mm hole in the rail for the mounting screw and mount the adapter onto the rail.. Fasten the soft closer to the adapters with screws. 7. Measure the distance between the door edge and the adapter ( X ). Installation of the soft closer trigger. Mount the trigger at the distance X + A from the track edge For the right-hand soft closer in the outer track, dimension A = mm. For the right-hand soft closer in the inner track, dimension A = 0mm. For the left-hand soft closer in the outer track, dimension A = 0mm. For the left-hand soft closer in the inner track, dimension A = mm. Before fixing the screws, drill lead holes in the top track with a mm drill bit. Montaż aktywatora domykacza. Zamontuj aktywator w odległości "X" + "A" od krawędzi toru. fixing screws Dla domykacza prawego w torze zewnętrznym wymiar "A" = mm. Dla domykacza prawego w torze wewnętrznym wymiar "A" = 9mm. Dla domykacza lewego w torze zewnętrznym wymiar "A" = 9mm. Dla domykacza lewego w torze wewnętrznym wymiar "A" = mm. X+A Right-hand X+A soft closer Domykacz inner prawy track tor wewnętrzny X+A Left-hand soft X+A closer Domykacz inner lewy track tor wewnętrzny X+A X+A Domykacz Right-hand prawy soft tor closer zewnętrzny outer track Aktywator Trigger X+A X+ALeft-hand Domykacz lewy soft tor closer zewnętrzny outer track

11 INDECO S00 SERIES STEEL SYSTEM bottom roller sliding doors Installation instructions Cut the tracks Carefully measure the width of the opening at top and bottom, and reduce the lengths measured by about - mm. Measure off the required track length, marking the future cut line on the tracks. Use a fine-toothed metal cutting saw to cut off the redundant part of the tracks. Advice: The tracks to be installed should be about 0 mm longer than the opening width. This spare length will make it possible to avoid measurement errors and it is easy to trim. Take care not to damage the track surface while cutting. In order to facilitate top track cutting, insert mm thick wood blocks or a reversed piece of track into the track. This will prevent track deflection during the cutting process. Install the top track Fix the top track with screws, offsetting its flat surface by mm from the door face (inwards). Install the top track with the shade line facing forward in order to mask ceiling irregularities. If a multiple-track system is installed, fix the other tracks so that they fit tightly against each other along the entire length. Advice: Before you start installation use a detector to make sure there is no electrical wiring at the screw fixing points. Avoid applying excessive force when tightening screws to prevent track deformation. Use flat-head screws for best results. The surface to which the track is fixed must not be curved. Install the door Lay the bottom track on the floor, offsetting it about 7 mm from the door face (inwards). Use a Philips screwdriver and the adjusting bolt to move bottom rollers out about 0 mm. Fully insert the door leaf in the top track, taking care not to damage the bottom rollers, then align the bottom end of the door leaf with the bottom track and slowly lower the leaf, letting the rollers snap into the track guides. Advice: Before you install the doors, put a cardboard sheet on the bottom track to prevent damage to track surface. When the doors are already in position, remove the protective cardboard. 9 Install the bottom track Use a level to make sure the door is exactly plumb; move the bottom track as necessary. Check if the door travels smoothly along the entire width of the opening. Having precisely set the bottom track, fasten it to the floor. Having installed the track, put the other door leaves in their respective tracks. Advice: Before you fix the bottom track, make sure that it is positioned exactly parallel to the top track. With soft floor covering, before you fix the bottom track, cut out a strip of about mm in width and replace it with a mm timber batten. Alternatively, put a 00 mm floor batten between the floor covering and the bottom track. Avoid applying excessive force when tightening screws to prevent track deformation. Use flat- -head screws for best results. ~7

12 INDECO S00 SERIES STEEL SYSTEM bottom roller sliding doors Installation instructions Adjust door position Adjust door position by means of a Philips screwdriver and the adjusting bolts in the bottom rollers so that the doors fit tightly against the wall along the entire length. Door-to-floor clearance is adjustable between 0 and 0 mm ( to mm from the bottom track). Fix the buffer and dust-stop brush strips Having installed the doors, remove protective backing from the door profiles. With the backing removed, you can fix the buffer strips and the dust-stop brush strips. To ensure good adhesion of the brush strips to the profiles, gently clean the profiles with alcohol or white spirit. Fix the strips, working from top to bottom. Cut off excess strip. 7 Fix the buffer strip clip To fix the clip 0999 or 0999A, the door must first be installed and adjusted. After that operation, fix the buffer strip and then mount the clip. For easier and correct installation, we recommend that the door should be taken off the tracks. Advice: For details of the buffer strip clip installation see separate instructions, Technical information fixing the buffer strip clip available on our website in the section designated for Authorised Partners. Fix the top positioners Fix the positioner 099 to the top track so that it fits against the middle part of the track at an appropriate distance from the wall. Cut the positioner 0999PLS to the right size and fix in the middle of the top track so that the door abuts on the side wall of the unit when closed. 0 For the profile x = mm, where no buffer strip is used, x = 7 mm, where a buffer strip is used. For the profile x = mm, where no buffer strip is used, x = 9 mm, where a buffer strip is used. 7 buffer strip dust stop brush x

13 INDECO S00 SERIES STEEL SYSTEM bottom roller sliding doors System components xx.9 Ø7. 0. Ø. Bottom Roller for Steel System. Body made from galvanized structural steel, designed for snap and screw fixing. The moving part is adjustable within the 0- mm range by means of an adjusting bolt and is provided with an anti-jump feature. The roller has a wheel of a high-strength plastic with an embedded sealed ball bearing. Resistance: up to 0 kg/ rollers, up to 0,000 open/close cycles. Packaging: 00 pcs/pack. Weight: ~.7 kg/pack. Twin Wheel Top Guide. Body made from galvanized structural steel, designed for snap and screw fixing. The guide features wheels of high- -strength plastic and vibration damping rubber. The moving part allows the wheels to be adjusted within the 0,, mm range. The wheels, fixed to an elastic moving arm, precisely follow the track. The guides are available in two versions: - with INDECO logo 0LL, - without INDECO logo 0LO. Packaging: 00 pcs/pack. Weight: ~.0 kg/pack. 000xx 0000xx 0. 0, Ø. Ø., 0700yyxx., Steel Double Bottom Track, m. Track made from galvanized zinc-coated steel sheet, finished with polyester paint or simulated wood film. Material thickness: 0. mm. Track length: 000 mm. Colours: xx: SSR, SSA, SGL, SWP, SBP, SVP, SBT, SET, SOT, SLT, SCT, SPT, SWT, SMT, SNT. Packaging: 0 pcs/pack. Weight: ~0. kg/pack. Steel Double Top Track, m. Track made from galvanized zinc-coated steel sheet, finished with polyester paint or simulated wood film. Material thickness: 0. mm. Colours: xx: SSR, SSA, SGL, SWP, SBP, SVP, SBT, SET, SOT, SLT, SCT, SPT, SWT, SMT, SNT. Packaging: pcs/pack. Weight: ~0. kg/pack. 000yyxx 0, 0. Steel Rail,. m. A rail for or 0 mm mirror panels to steel door systems. Made from galvanized zinc-coated steel sheet, finished with polyester paint or simulated wood film. Material thickness: 0. mm. Versions: yy: 0 mm, 0 0 mm Colours: xx: SSR, SSA, SGL, SWP, SBP, SVP, SBT, SET, SOT, SLT, SCT, SPT, SWT, SMT, SNT. Packaging: 0 pcs/pack. Weight: ~.0 kg/pack. 9. 9, Steel Stile,.7 m. A stile for or 0 mm mirror panels to steel door systems. Made from galvanized zinc-coated steel sheet, finished with polyester paint or simulated wood film. Versions: yy: 0 mm, 0 0 mm. Colours: xx: SSR, SSA, SGL, SWP, SBP, SVP, SBT, SET, SOT, SLT, SCT, SPT, SWT, SMT, SNT. Packaging: 0 pcs. Weight: ~0.00 kg/pack.

14 INDECO S00 SERIES STEEL SYSTEM bottom roller sliding doors System components 7 00yyxx Steel Stile,,7 m. A stile for or 0 mm mirror panels to steel door systems. Made from galvanized zinc-coated steel sheet, finished with polyester paint or simulated wood film. Versions: yy: 0 mm, 0 0 mm Colours: xx: SSR, SSA, SGL, SGP, SWP, SBP, SVP, SBT, SET, SOT, SLT, SCT, SPT, SWT, SMT, SNT. Packaging: pcs. Weight: ~9.0 kg/pack. 000yyxx or 0., Top Positioner. A component that holds in position steel system doors. Packaging: 0 pcs/pack. Weight: ~0. kg/pack. 0999PLS Positioner, grey plastic. Sets the S00 system door leaf in the end position. It is stuck to the top track. Application: S xx.7 Steel Stile,.7 m. A stile for or 0 mm mirror panels to steel door systems. Made from galvanized zinc-coated steel sheet, finished with polyester paint or simulated wood film. Versions: yy: 0 mm, 0 0 mm Colours: xx: SSR, SSA, SGL, SGP, SWP, SBP, SVP, SBT, SET, SOT, SLT, SCT, SPT, SWT, SMT, SNT. Packaging: 0 pcs/ pack. Weight: ~0.00 kg/pack. Self-adhesive Dust-stop Brush.7 x. A brush designed to seal the space between door leaves and to stop dust. Hair length: mm. Colours: xx: 00 white, 0 black, brown, beige, 0 - grey. Packaging: 00, 0,, - 00 m/roll 0-00 m/roll. Weight: 00, 0,, - ~.0 kg/roll. 0 -~. kg/roll. Availability: continuous (white, beige, grey); to order (other colours). 000xx 9 00yyxx or 0.7 Steel Stile,.7 m. A stile for or 0 mm mirror panels to steel door systems. Made from galvanized zinc-coated steel sheet, finished with polyester paint or simulated wood film. Versions: yy: 0 mm, 0 0 mm. Colours: xx: SSR, SSA, SGL, SGP, SWP, SBP, SVP, SBT, SET, SOT, SLT, SCT, SPT, SWT, SMT, SNT. Packaging: pcs/pack. Weight: ~9.0 kg/pack. Self-adhesive Dust-stop Brush.7 x. A brush designed to seal the space between door leaves and to stop dust. Hair length: mm. Colours: xx: 9 - grey. Packaging: 00 m/roll. Weight: ~. kg/roll Bottom Roller Guard left/right A set of bottom roller guards (right and left) for steel systems. Colour: grey. Packaging: 0 sets/pack. Weight: ~.9 kg/pack.

15 09000xx Steel Connector Rail,.7 m. A universal profile designed for horizontal and vertical joints between different panel types with a thickness of and 0 mm. Made from galvanized zinc-coated steel sheet, finished with polyester paint or simulated wood film. Colours: xx: SSR, SSA, SGL, SGP, SWP, SBP, SVP, SBT, SET, SOT, SLT, SCT, SPT, SWT, SMT, SNT. Packaging: pcs/pack. Weight: ~9.00 kg/pack. 099x.7. Fig. Fig. INDECO S00 SERIES STEEL SYSTEM bottom roller sliding doors System components 0000xx Self-adhesive Buffer Strip,.x or. x. A strip designed to dampen door impact against the wall and eliminate minor wall irregularities. Hair length: mm or mm. Colours: xx: 00 white, 0 black, brown, beige, 0 - grey Packaging: 0m/roll grey; 0 m/roll other colours. Weight: ~.90 kg/roll. Availability: continuous (white, beige, grey); to order (other colours) xx Spacer for steel system with combination panels. Length:.7 m.versions: x: 0 Fig. (0// vertical). Fig. (0//0 horizontal). Packaging: 0-0 pcs/pack., - 0 pcs/pack. Weight: 0 - ~. kg/pack, - ~. kg/ pack..7,7 Stick-on Decorative Strip. Length:. m. A decorative steel strip to be stuck on the steel system panel. Made from galvanized zinc-coated steel sheet, finished with polyester paint or simulated wood film. Colours: xx: SSR, SSA, SGL, SGP, SWP, SBP, SVP, SBT, SET, SOT, SLT, SCT, SPT, SWT, SMT, SNT. Packaging: 0 pcs/ pack. Weight: ~0.00 kg/pack. 0000xx > see page 0 Self-adhesive Safety Backing. Steel System Soft Closer Accessories. These items are used to fix the universal soft closer to a steel system door leaf. The steel system door closer accessories include: - Trigger - Soft closer adapter, right - Soft closer adapter, left - Adjusting screw.9 x 9mm ( pce) - Trigger mounting screws. x mm ( pcs) - Soft closer adapter mounting screws.9 x mm ( pcs) - Soft closer mounting screws M x mm ( pcs) - Soft closer adapter mounting rivets ( pcs) Application: S x Buffer Strip Clip. A clip preventing the buffer strip from coming unstuck. Color: silver. Packaging: 00 pcs/pack. Weight: ~0.0 kg/pack A Buffer Strip Clip. A clip preventing the buffer strip from coming unstuck. Color: silver. Packaging: 00 pcs/pack. Weight: ~0. kg/pack.. Universal Soft Closer. It ensures that the door leaf closes softly to its end position. The soft closer features an air damper, which guarantees durability and performance stability throughout its useful life. The design of the soft closer body allows it to be used as a left-hand or right-hand closer. The installation of the soft closer on the steel system-based door leaf is possible with the use of the steel system door closer accessories 099. The soft closer is available in two versions: 099 soft closer for doors of up to kg in weight. 099 soft closer for doors of to 0kg in weight. Application: S00, A00, A00.

16 INDECO S00 SERIES STEEL SYSTEM bottom roller frameless sliding doors, mm Boundary conditions: - maximum dimensions of the opening: 00 mm in height; any width with sections of up to 000 mm each. - maximum dimensions of individual doors: 00 mm in height, 00 mm in width or, for light doors not exceeding 0 kg, the door width can be increased to 000 mm. - maximum weight of 0 kg. - panel thickness of mm. SERIA S00 - DRZWI PRZESUWNE (system stalowy)

17 INDECO S00 SERIES STEEL SYSTEM bottom roller frameless sliding doors, mm Components , Assembly Drawing xx 000xx 0000xx 00xx Bottom Roller C Profile Twin Wheel Top Guide Steel Bottom Track Steel Top Track Symmetrical Aluminium Decorative Profile xx PLS xx 099X 099 Non-symmetrical Aluminium Decorative Profile / x Distance Sleeve Top Positioner Positioner, grey plastic. x Screw Stick-on Decorative Strip Universal Soft Closer Soft Closer Trigger

18 INDECO S00 SERIES STEEL SYSTEM bottom roller frameless sliding doors, mm Fabrication instructions Calculate door front dimensions > see page Define the number of overlaps > see page Frameless panels Calculate door leaf dimensions Overlap width = 0 mm Door leaf width: DW = OW + z * 0 mm n Door leaf height: DH = OH 0 mm Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: PW = DW Panel length: PL = DH Frameless panels Calculate door leaf dimensions Overlap width = 0 mm Door leaf width: DW = OW + z * 0 mm n Door leaf height: DH = OH mm Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: PW = DW mm Stile length: SL = DH Rail length: RL = DW Door panel Having cut the panel to the required dimensions, apply the appropriate edge finish (veneer, paper, PVC edging or C profile). For aluminium decorative framing, cut a mm wide and 0 mm deep groove in the panel edges. 7 Install decorative profiles Put one end of the profile against the corresponding end of the panel and tap the profile in place using a rubber mallet along the entire length, so that it protrudes mm at each end of the panel. Fix the other profiles likewise. Fix bottom rollers and top guides Before fixing the rollers and guides, break off the tongues (two in each bottom roller and one in each top guide). Use. x screws and distance sleeves 099 to fix the rollers and guides to panel corners. To fix the rollers and guides to the side, use. x screws (if no decorative profiles are used) or. x screws (if decorative profiles are used). Fix the other rollers likewise. Advice: To protect the anti-jump feature against damage or breaking, the bottom roller wheel should be fully recessed into the roller body during transport. Note: Fix buffer strips only after door installation has been completed. DW 7 PW DH PL SL RL

19 INDECO S00 SERIES STEEL SYSTEM bottom roller frameless sliding doors, mm Installation instructions Cut the tracks > see page 9 Install the bottom track > see page 9 Install the top track > see page 9 Adjust door position > see page 0 Set the door in place > see page 9 7 Fix the buffer strips Having set the door in place, you can attach the buffer strips. Fix the strips, working your way from top to bottom. Cut off excess strip. Fix the top positioners Fix the positioner to the top track so that it abuts the middle part of the track at an appropriate distance from the wall. Mark the x position of the guide wheel and the positioner with the door closed. 7 7 x

20 INDECO S00 SERIES STEEL SYSTEM bottom roller frameless sliding doors, mm System components 00 > see page Bottom Roller for Steel System xx C Profile. Length: m. Colours: xx: AS, AG,AC, AO Packaging: 00 pcs/pack. Weight: ~.9 kg/pack. 0xx > see page 9 0 Distance Sleeve. A distance sleeve for fixing rollers and guides to mm board (S00 system). Packaging: pce/pack. Weight: ~0.00 kg/pack > see page Top Positioner. 0999PLS > see page Positioner, grey plastic. Twin Wheel Top Guide with Bearing. 000xx > see page Steel Double Bottom Track. 0000xx > see page Steel Double Top Track xx 9. x Self-tapping Screw. Countersunk self-tapping screw for fixing rollers (S00). Packaging: 000 pcs/pack. Weight: ~.0 kg/pack. Symmetrical Aluminium Decorative Profile. Length: m. A symmetrical aluminium decorative T profile for mm laminated board edging. Colours: xx: AS natural anodized. Packaging: 0 pcs/pack. Weight: ~. kg/pack xx > see page Stick-on Decorative Strip. 099X > see page Universal Soft Closer xx > see page Steel System Soft Closer Accessories.. Non-symmetrical Aluminium Decorative Profile. Length: m. A non-symmetrical aluminium decorative T profile for mm laminated board edging. Colours: xx: AS natural anodized. Packaging: 0 pcs/pack. Weight: ~0.0 kg/pack.

21 INDECO S00 SERIES STEEL SYSTEM pivoted doors Boundary conditions: - maximum dimensions of the opening: 00 mm in height; any width with sections of up to 000 mm each. - maximum dimensions of individual doors: 70 mm in height, 00 mm in width. - maximum weight of kg. - panel thickness of mm or 0 mm.

22 INDECO S00 SERIES STEEL SYSTEM pivoted doors Components * * / 7/ 7/ Assembly Drawing 7 7/ 0700yyxx 000yyxx 00yyxx 0000xx Steel Rail Steel Stile Steel Stile Buffer Strip or Dust Stop Brush Strip Bottom Roller Guard, left/right Magnetic Latch and Keeper S00 Hardware Set - Pivot Pin 7/ 7/ Connector with Pivot Socket - Connector // Spacer 099 0//0 Spacer 0999 Buffer Strip Clip 0999A Buffer Strip Clip 09000xx Steel Connector Rail 09000xx Stick-on Decorative Strip

23 INDECO S00 SERIES STEEL SYSTEM pivoted doors Fabrication instructions Calculate door front dimensions > see page Define the number of door leaves Define the number of pivoted door leaves n number of leaves Profile Calculate door leaf dimensions Door door leaf width: n = ( leaf) DW = OW 0 n = ( leaves) OW 7 DW = Door leaf height: DH = OH mm Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel (board or mirror) width: PW = DW mm for board PW = DW mm for mirror Panel (board or mirror) length: PL = DH mm Stile length: SL = DH Rail length: RL = DW mm for board RL = DW 0 mm for mirror Profile Calculate door leaf dimensions Door door leaf width: n = ( leaf) DW = OW 9 n = ( leaves) DW = OW Door leaf height: DH = OH mm Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel (board or mirror) width: PW = DW 9 mm for board PW = DW mm for mirror Panel (board or mirror) length: PL = DH mm Stile length: SL = DH Rail length: RL = DW mm for board RL = DW 7 mm for mirror Advice: For uneven door leaf widths, adjust the above calculations so that where one door leaf is wider, the other leaves are narrower by a corresponding aggregate dimension. Mirror protection > see page 9 Install rails > see page Combination panels > see page 0 Fix bottom rollers and top guides > see page 7 7 Instal stiles > see page Structural reinforcement > see page 7 Tap stiles and spacers onto panels > see page DW PW n= OH DH PL SL OW n= RL

24 INDECO S00 SERIES STEEL SYSTEM pivoted doors Installation instructions Install pivot pins Set and fix the top and bottom pivot pins, offsetting them mm inwards from the door face and at the following distance from the side wall: x = mm for the profile x = mm for the profile Note: When fixing the pivot <?>base, use screws with a head diameter of not more than mm. Set the door in place Use a Philips screwdriver and the adjusting bolts to insert the pivot socket slides in the connectors about 0 mm. Move the sockets outwards and fasten the socket fixing screw. Put the door upright so that the connectors with pivot sockets are aligned with the axis of the fixed pivot pins. The door should be in an open position. While turning the adjusting bolt, slip the bottom pivot socket slide out so that the socket is aligned with the pin and the door lifts slightly. Then slip out the top sliding pivot socket so that it is aligned with the pin, allowing for minimal play. Advice: Exercise special care when installing doors. This operation should be performed by two persons. Adjust the door Using a Philips screwdriver and adjusting bolts in the top and bottom <?>connectors, adjust the door height. The door-tofloor/ceiling distance is adjustable between and 0 mm. Fix the buffer strips Having installed the doors, remove safety backing from the door profiles. With the backing removed, you can fix the buffer strips. To ensure good adhesion of the strips to the profiles, gently clean the profiles with alcohol or white spirit. Fix the strips, working your way from top to bottom. Cut off excess strip. Advice: Owing to a large gap between the wall and door, it is recommended that you use a dust stop brush strip instead of a buffer strip. Fix the buffer strip clip > see page 0 Fix the magnetic latch Having adjusted the door, close it, place the magnetic latch at the door leaf, mark the position and open the door. Fix the magnetic latch to the floor/ceiling/wall. Note: The latch keeps the door in a stable position when closed.

25 INDECO S00 SERIES STEEL SYSTEM pivoted doors System components 0700yyxx > see page Steel Rail. 000yyxx > see page Steel Stile. 00yyxx > see page Steel Stile. 0000xx > see page Self-adhesive Buffer Strip. 0000x > see page Bottom Roller Guard, left/right Magnetic Latch with Keeper. Automatic magnetic latch for pivoted doors with a self- -adhesive keeper Packaging: pce/pack. Weight: ~0.0 kg/pack A set of hardware for steel systems with S00 pivoted doors. Packaging: set. Weight: ~0. kg/set x > see page Spacer for steel system with combination panels >see page Buffer Strip Clip. 0999A > see page Buffer Strip Clip xx > see page Steel Connector Rail xx > see page Stick-on Decorative Strip.

26 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors Boundary conditions: - maximum dimensions of the opening: 000 mm in height (or up to 00 in light panel applications); any width with sections of up to 000 mm each. - maximum dimensions of individual doors: 70 mm in height, 00 mm in width or, for light doors not exceeding 0 kg, the door width can be increased to 000 mm and the height to 00 mm. - maximum weight of 0 kg. - panel thickness of mm and 0 mm.

27 , INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors Components * 0,9, 7, 0, ,7, 0 Ø/9,7 7, 0, *, 9 0,, Rysunek złożeniowy xx 0xx 0999x 000xx 0xx 00xx 0xx xx 0xx 0xx 0xx 0xx 0xx 07xx 07xx 09xx xx 00xx 0xx 00xx 00xx 00xx xx xx xx 0xx Bottom Roller (complete) Top Guide for Top Guide for profiles Bottom Positioner Aluminium Double Bottom Track Aluminium Bottom Track Facia Aluminium Double Top Track Aluminium Rail, Narrow Aluminium Rail, Wide Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Single Bottom Track Aluminium Triple Bottom Track Aluminium Single Top Track Aluminium Triple Top Track Aluminium Connector Rail Narrow Aluminium Connector Rail mm Aluminium Connector Rail mm Decorative Strip profiles xx xx 0000xx 000xx 0000x 0000A xx 0xx 0SU xx x A Aluminium Decorative Profile Plug Gasket Buffer Strip Dust Stop Brush Strip Lock. x Self-tapping Screw Aluminium Recessed Single Bottom Track Alu. Recessed Wide Single Bottom Track Recessed Single Bottom Track Mounting Profile Self-adhesive Cap INDECO Self-adhesive Cap Safety Backing Top Track Stopper Single Top Track End Cap Double Top Track End Cap Bottom Track Stopper Double Bottom Track End Cap Single Bottom Track End Cap, left/right Double-sided Self-adhesive Tape Positioner Buffer Strip Clip Buffer Strip Clip Aluminium System Universal Soft Closer Accessories Universal Soft Closer

28 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors Fabrication instructions Calculate door front dimensions > see page Define the number of overlaps > see page profile Calculate door leaf dimensions Overlap width = mm Door leaf width: SD = (SO + z * mm) / n where: OW = opening width DW = door leaf width z number of overlaps n number of leaves Door leaf height: DH = OH DH = OH 0 (for recessed tracks) DH = OH (with soft closer) DH = OH 9 (with soft closer and recessed tracks) where: OH = opening height Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm, mirror: PW = DW 9 mm Panel length: board: PL = DH mm, mirror: PL = DH 0 mm Rail length: RL = DW mm Stile length: SL = DH profile Calculate door leaf dimensions Overlap width = mm Door leaf width: DW = (OW + z * mm) / n where: OW = opening width DW = door leaf width z number of overlaps n number of leaves Door leaf height: DH = OH DH = OH 0 (for recessed tracks) DH = OH (with soft closer) DH = OH 9 (with soft closer and recessed tracks) where: OH = opening height Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm, mirror: PW = DW mm Panel length: board: PL = DH mm, mirror: PL = DH 0 mm Rail length: RL = DW 0 mm Stile length: SL = DH Advice: For uneven door leaf widths, adjust the above calculations so that where the central door leaf is wider, the other leaves are narrower (by half of the difference each for a three-leaf front). profile Calculate door leaf dimensions Overlap width = 0 mm Door leaf width: DW = (OW + z * 0 mm) / n where: OW = opening width DW = door leaf width z number of overlaps n number of leaves Door leaf height: DH = OH DH = OH 0 (for recessed tracks) DH = OH (with soft closer) DH = OH 9 (with soft closer and recessed tracks) where: OH = opening height Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm, mirror: PW = DW mm Panel length: board: PL = DH mm, mirror: PL = DH 0 mm Rail length: RL = DW 7 mm Stile length: SL = DH DW PW DH PL SL RL

29 profile Calculate door leaf dimensions Overlap width = mm Door leaf width: DW = (OW + z * mm) / n where: OW = opening width DW = door leaf width z number of overlaps n number of leaves INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors Fabrication instructions Door leaf height: DH = OH DH = OH 0 (for recessed tracks) DH = OH (with soft closer) DH = OH 9 (with soft closer and recessed tracks) where: OH = opening height Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm, mirror: PW = DW mm Panel length: board: PL = DH mm, mirror: PL = DH 0 mm Rail length: RL = DW mm Stile length: SL = DH 7 profile Door leaf height: Calculate door leaf dimensions DH = OH Overlap width: mm DH = OH 0 (for recessed tracks) Door leaf width: DH = OH (with soft closer) SD = (SO + z * mm) / n DH = OH 9 (with soft closer and recessed tracks) where: where: OH = opening height OW = opening width Cut components DW = door leaf width Based on door leaf dimensions, cut the components to the following dimensions: z number of overlaps Panel width: board: PW = DW mm, mirror: PW = DW mm n number of leaves Panel length: board: PL = DH mm, mirror: PL = DH 0 mm Rail length: RL = DW mm Stile length: SL = DH Combination panels For combination panels joined by connectors, apply the following relation to calculate panel dimensions: For connector xx in Fig. A: Calculating panel lengths with the use of connectors: SPL =PL (k * 7) (z * ) where: k number of connectors z number of glass panels SPL sum of panel (n) lengths PL panel length For connector xx in Fig. B: Calculating panel lengths with the use of connectors: SPL =PL k (z * ) where: k number of connectors z number of glass panels SPL sum of panel (n) lengths PL panel length Mirror protection > see page Drill assembly holes Prior to leaf assembly, drill /9.7 mm holes in each stile. They will be used to fix: Hole A: the top rail and the top guide with a self-tapping screw, and to fix and adjust the bottom wheel with a bolt. Hole B: the bottom rail with a self-tapping screw. Preferably, drill the holes using the subland drill 0000 and drill jig for aluminium profiles or fig. A fig. B A A B A PL... B 0 0 A B A

30 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors Fabrication instructions Drill assembly holes, ctd. Drill jig is intended for making holes with a hand-held drill, while drill jig 0000 is designed for making holes by means of a bench drill. Both jigs are all-purpose devices, and can be used for drilling holes in all types of stiles. Install connector rails Put one end of the connector rail against the corresponding end of the panel joint. Use a rubber mallet to tap the rail profile in place along the entire panel width. Then carefully tap the other part of the panel into the rail. A panel joint may be curved. In order to obtain the desired shape of the connector rail, use the profile bending tool Lift the handle, insert the profile under the bearings and gently bend the profile with the handle. Lock the handle in position with the dowel pin. Turn the crank to bend the profile over a desired length. Repeat the cycle until the desired bend radius is obtained. Advice: Owing to panel (mirror, glass or laminated board) cutting tolerances, panel dimensions may differ slightly from the desired ones. Cut the bent connector rails to the desired dimensions only after you have produced the required shape. Avoid sharp bending to make sure the anodized coat remains undamaged. Install stiles Put one end of the stile against the corresponding end of the panel and tap the stile in place using a rubber mallet along the entire length, so that it protrudes as desired at both ends of the panel. Fix the other stile likewise. Advice: To determine an appropriate protrusion, put a piece of rail against the panel. For a mirror, exercise special care when you start fixing the stile. Tap the stile carefully in position on the panel. Before fixing the stile, fit the seal in one piece. Start attaching the seal from the centre of the upper edge of the mirror. Make a cut in the seal at each corner of the mirror, using a sharp knife. When fitting the seal, it should be slightly stretched. Where the doors are to be provided with panels composed of several different materials, join all the materials together before fixing the stiles. Install rails Put one end of the rail against the stile. Use a rubber mallet to tap the rail in place along the entire length. Fix the narrow rail likewise. Advice: Owing to panel (mirror, glass or laminated board) cutting tolerances, panel dimensions may differ slightly from the desired ones. To avoid problems, before cutting the rails, measure the distance between the stiles and cut the rails to that length. When using panels slightly thicker than 0 mm (e.g. rattan), it is recommended that you put two blocks before fixing the bottom rail. Fix symmetrical top guides For the profiles: ) Fix the screw, leaving about mm between the screw head and the profile. ) Insert guide 07 or 07xx tongues under the head of the self-tapping screw 0000A. ) Tighten the screw, fastening the profiles and the guide together. Fix the other guide likewise. Fix non-symmetrical top guides For the profile: ) Fix the screw, leaving about mm between the screw head and the profile. ) Insert guide 0 or 0xx tongues into the profiled channels in the stile. ) Fasten the narrow rail and the stile together with a self-tapping screw. Fix the other guide likewise.

31 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors Fabrication instructions 7 Fix bottom rollers Fasten the bottom rail to the stile with the self-tapping screw 0000A. Unscrew the bottom roller adjusting bolt with washer. Insert the bolt with washer into the hole in the stile. Insert the roller into the bottom rail so that it touches the stile. Using a power screwdriver, partly drive the adjusting bolt into the roller. Fix the other roller in the same manner. Advice: Having fixed the bottom rollers, push them into the profile and protect against slipping out and damage in transport by means of protective adhesive tape. For low doors (ceiling storage units, lockers) remove springs from the bottom rollers. This will prevent lifting of light door leaves. Structural reinforcement In order to reinforce the door leaf structure with combination panels, you can optionally fix the connector rail to the stiles with self-tapping screws 0000A. Advice: Before tapping the stile in place, drill screw holes for additional fixing of the connector rail using a subland drill Note Fix buffer strips and dust-stop brush strips only after door installation has been completed. Fix plugs only after the doors have been adjusted. The entire glass surface (mirror, stained glass) should be secured with safety backing 0000 or 0000 in compliance with the applicable laws and regulations. Only laminated safety glass may be used for transparent inserts. In order to reduce the risk of glass cracking as a result of stress produced during cutting, make sure that glass edges are ground smooth with abrasive paper or stone. 9 mm, 7

32 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors Installation instructions Cut the tracks Carefully measure the width of the opening at top and bottom, and reduce the lengths measured by about - mm. Measure off the required track length, marking the future cut line on the tracks. Use a fine-toothed metal cutting saw to cut off the redundant part of the tracks. Advice: The tracks to be installed should be about 0 mm longer than the opening width. This spare length will make it possible to avoid measurement errors and it is easy to trim. In order to facilitate top track cutting, insert mm thick wood blocks or a reversed piece of track into the track. This will prevent track deflection during the cutting process. Install the top track Fix the top track with screws, offsetting its flat surface by mm from the door face (inwards). Install the top track with the shade line facing forward in order to mask ceiling irregularities. If a multiple-track system is installed, fix the other tracks so that they fit tightly against each other along the entire length. Advice: Avoid applying excessive force when tightening screws to prevent track deformation. Use flat-head screws for best results. The surface to which the track is fixed must not be curved. 0 Fix stoppers and positioners in the bottom track If the track is to be fitted with bottom positioners and stoppers, slip them into the respective tracks before fixing. Fully insert the door leaf in the top track, taking care not to damage the bottom rollers, then align the bottom end of the door leaf with the bottom track and slowly lower the leaf, letting the rollers snap into the tracks. For door weights under kg use positioner 0999A. For door weights between kg and kg use positioner For door weights between kg and 0 kg use positioner 0999B. Install the door Lay the bottom track on the floor, offsetting it from the door face (inwards) by about: x = mm - profile x = mm - profile If the track is to be fitted with bottom positioners, slip them into the respective tracks before fixing. Fully insert the door leaf in the top track, taking care not to damage the bottom rollers, then align the bottom end of the door leaf with the bottom track and slowly lower the leaf, letting the rollers snap into the tracks. Advice: Before you install the doors, put a cardboard sheet on the bottom track to prevent damage to track surface. When the doors are already in position, remove the protective cardboard. x

33 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors Installation instructions Install the bottom track Use a level to make sure the door is exactly plumb; move the bottom track as necessary. Check if the door travels smoothly along the entire width of the opening. Having precisely adjusted the door position, install the other door leaves in their respective tracks. Advice: Before you fix the bottom track, make sure that it is positioned exactly parallel to the top track. With soft floor covering, before you fix the bottom track, cut out a strip of about mm in width and replace it with a mm timber batten. Alternatively, put a 00 mm floor batten between the floor covering and the bottom track. Avoid applying excessive force when tightening screws to prevent track deformation. Use flat-head screws for best results. Adjust door position Adjust door position by means of the adjusting bolts in the bottom rollers so that the doors fit tightly against the wall along the entire length. Door-to-floor clearance is adjustable between and 0 mm ( to mm from the bottom track). 7 Fix the top track stopper Before fixing the stopper, drill through-holes with a mm drill bit. Then fix the stopper to the ceiling (upper wall) using screws suitable for the ceiling/wall material. If you install an end cap in the top track, insert the cap tabs between the track and the ceiling before finally fastening the stopper screws. Adjust the bottom stopper and top stopper Having installed the top track stopper, adjust the position of the stopper 0997 set in the bottom track. To do this, slide the door to the top stopper as shown in Fig. and push the bottom stopper to the wheel edge (Fig. ). Fasten the bottom stopper screw with a. mm Allen key to prevent its dislocation when the door is used.. 7 fig. fig. mm

34 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors Installation instructions 9 Fix the positioner/stopper Insert the positioner/stopper into the bottom track before is installation. After the bottom track is fixed to the floor, tighten the positioner with an Mx ISO 0 set screw (the key and the screw are delivered in the kit). Remount the door and install it in the right position. The distance between the positioner and the end of the track X depends on the stile (vertical profile) used. This way you can easily verify if the positioner is fixed properly and in which direction it should be moved if needed. The positioner can be used in all bottom tracks: - single 000xx, - double 0xx, - wide recessed single track 0xx, - narrow recessed single track xx. 0 Fix the caps Having installed and adjusted the door leaves, cover all installation holes by inserting the plugs or by sticking the caps or Fix the dust-stop brush strips and buffer strips To ensure good adhesion of the strips to the profiles, gently clean the profiles with alcohol or white spirit. Fix the strips, working your way from top to bottom. Cut off excess strip. Advice: for profiles, use a shorter mm strip For other profiles, use a longer mm strip Fix the buffer strip clip > see page. 0 Fix the decorative strips Having adjusted the door leaf height, mark the levels where decorative strips are to be fixed to the door leaves. For each leaf, carefully measure the distance between the stiles. Then cut the decorative strips to the required lengths and fix double-sided self-adhesive tape (0. mm thick) to the strips. Remove the protective tape and, bending the strip slightly, put it between the stiles and press against the panel. 9 0

35 9 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors Installation instructions Fix the decorative profile designed for the Hudson profile The bottom track fascia 0xx can be used as a decorative profile. For this purpose, fix double-sided self-adhesive tape to the profiled indent and then stick the profile to the door leaf. Install the locks Fix the lock cylinder to the body with.9 x screws Fix the body with the attached cylinder to the stile on the outer door leaf with.9 x self-tapping screws Putting the door leaf in closed position, mark the outline of the lock body on the inner door. Then fix the lock base at the marked location on the board panel with.9 x self-tapping screws , using two previously drilled holes. For a mirror, fix the lock base using double-sided self-adhesive tape Adjust the bottom positioners Put the door in set positions. Mark the positions of the bottom roller wheels. Slide the door to the side, press the positioner tips in place, and move the door to the desired position. Advice: For light (narrow) doors use a single bottom positioner for each leaf; for heavy (wide) doors use two positioners per leaf.

36 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors Installation instructions 7 Fix the recessed bottom tracks Recessed track: The recessed bottom track can be fixed in ceramic or parquet flooring or to furniture board. Leave or make a groove of - mm in width and min. 7 mm in depth. Fix the track using silicon adhesive. Prior to fixing the track, apply an appropriate quantity of the adhesive along the bottom of the groove. Where two or more tracks are installed, provide for 0. mm spacing on centres (distance between track centre lines). Track recessed into ceramic flooring: A recessed bottom track can be mounted in ceramic flooring. Leave a groove of - mm in width and at least 9 mm in depth, in which to install the mounting profile 0SU or embed it in mortar before it sets. Prior to door installation, fix the track xx using silicone adhesive. Wide recessed track: The wide recessed track can be installed under carpeting. Fix the track using screws, double-sided self-adhesive tape or silicon adhesive. Where two tracks are installed, correct spacing of tracks will be obtained by laying them next to each other so that the wider sides of their bases abut. Advice: In an uneven floor, fix the tracks with silicon adhesive. Fix the single or double top track end cap Single and double top tracks can be fitted with end caps if the tracks are shorter than the width of the opening or they are installed outside the opening fitted with sliding doors. Before finally fastening the track fixing screws, insert the cap tabs between the track and the ceiling. Then fasten the track fixing screws. 7 - mm min 7mm silicon adhesive 0. - mm min 9 mm silicon adhesive 0. 0.

37 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors Installation instructions 9 Fix the single or double bottom track end cap Insert the cap into the single or double bottom track. Having done this, fasten the cap with a. mm Allen key. 0 Mount the fascia Install the bottom track fascia 0xx, resting the special indent in the fascia on the bottom track rib. Then press the fascia until it snaps into place. Mount the universal soft closer. Fasten the universal soft closer 099X to the narrow rail with adapters and. x screws (aluminium system soft closer accessories). Having fastened the soft closer, measure the distance between the door edge and the soft closer ( X ). Mount the soft closer trigger Mount the trigger at the distance X + A from the track edge, fixing it to the top track with. x screws. For the right-hand soft closer in the outer track, dimension A = mm. For the right-hand soft closer in the inner track, dimension A = 0mm. For the left-hand soft closer in the outer track, dimension A = 0mm. For the left-hand soft closer in the inner track, dimension A = mm. Before fixing the screws, drill lead holes in the top track with a mm drill bit. 9 0 X+A Right-hand soft closer inner track X+A Left-hand soft closer inner track X X+A Right-hand soft closer outer track X+ALeft-hand soft closer outer track

38 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors System components x Bottom Roller for Aluminium System. Body made from high-impact structural plastic. The moving part is adjustable within the 0- mm range by means of an adjusting bolt and is provided with a spring anti-jump feature. The roller has a wheel of a high- -strength plastic with an embedded sealed, lubricated steel ball bearing. The set comes with the adjusting bolt and washer. Resistance: up to 0 kg/rollers, up to 0,000 open/close cycles. Packaging: 00 pcs/pack. 07xx Symmetrical Top Guide with Bearing for aluminum profiles. The guide is of durable steel construction. Two permanently riveted wheels of high- -strength plastic and vibration damping rubber ensure extremely quiet operation. Available in two versions: - with the INDECO logo - 07LL, - without the INDECO logo - 07LO. Packaging: 00 pcs/pack. Weight: ~. kg/pack. 0xx Non-symmetrical Top Guide with Bearing for aluminium profiles. The guide is of durable steel construction. Two permanently riveted wheels of high-strength plastic and vibration damping rubber ensure extremely quiet operation. Available in two versions: - with the INDECO logo - 0LL, - without the INDECO logo - 0LO. Packaging: 00 pcs/pack. Weight: ~.7 kg/pack A Bottom Positioner. A component that holds in position aluminium system doors up to kg Bottom Positioner. A component that holds in position aluminium system doors of kg to kg. 0999B Bottom Positioner. A component that holds in position aluminium system doors of kg to 0 kg. Packaging: pce/pack. Weight: ~0.00 kg/pack. 000xx Aluminium Double Bottom Track. Length: m. Track made from aluminium alloy, anodized or finished in simulated wood paint. Colours: xx: AS, AC, AMW, AAW, AWW, AWP. Packaging: 0 pcs/pack. 0xx. 9. 9, 9. 9, Double Bottom Track Fascia. Length: m. Can be used as decorative profile with the Hudson profile. Colours: AS, AC, AMW, AAW, AWW, AWP. Packaging: 0 pcs/pack Weight: ~0.7 kg/pack.., 00xx 0. 0, ,, Aluminium Double Top Track. Length: m. Made from aluminium alloy, anodized or finished in simulated wood paint. Colours: xx: AS, AC, ASB, ACB, AMW, AAW, AWW, AWP. Packaging: pcs/pack. Weight: ~.00 kg/pack.

39 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors System components 7 0xx 0x 0, , , Narrow Aluminium Rail, 0 mm. Length: m. A rail for 0 mm board, or mm glazing or mm mirror panels. Made from aluminium alloy, anodized or finished in simulated wood paint. Colours: xx: AS, AC, ASB, ACB, AMW, AAW, AWW, AWP. Packaging: 0 pcs/pack. Weight: ~.90 kg/pack. 9, 9.., 9. 9, Aluminium Stile, 0 mm. Length:. m. A profile for 0 mm board, or mm glazing or mm mirror panels. Made from anodized aluminium alloy. Colours: xx: AS, AC, AWP. Packaging: pcs/pack. Weight: ~. kg/pack. xx.7,7,7.7 Wide Aluminium Rail, 0 mm. Length: m. A general-purpose rail for top roller aluminium system. Colours: xx: AS, AC, ASB, ACB, AMW, AAW, AWW, AWP. Packaging: pcs/pack. Weight: ~. kg/pack. 9 0xx, 9, 0xx,. 9. 9,,7.7 Aluminium Stile, 0 mm. Length:. m. A profile for 0 mm board, or mm glazing or mm mirror panels. Made from aluminium alloy, anodized or finished in simulated wood paint. Profile length: 000 mm. Colours: xx: AO, AZ, AS, AC, ASB, ACB, AMW, AAW, AWW, SRP, SRM, GRP. Packaging: pcs/pack. Weight: ~.7 kg/pack. 7 7 Aluminium Stile, 0 mm. Length:. m. A stile for 0 mm board, or mm glazing or mm mirror panels. Made from aluminium alloy, anodized or finished in simulated wood paint. Colours: xx: AO, AG, AS, AC, ASB, ACB, AMW, AAW, AWW, AWP, ASP, ASM, AGP. Packaging: 0 pcs/pack. Weight: ~7.0 kg/pack. 0 0xx., 9. 9, Aluminium Stile, 0 mm. Length:. mm. A profile for 0 mm board, or mm glazing or mm mirror panels. Made from aluminium alloy, anodized or fi- 7 nished in simulated wood paint. Colours: xx: AS, AC, AWP. Packaging: 0 pcs/pack. Weight: ~7.0 kg/pack. 07xx., 9. 9, 0 Aluminium Stile, 0 mm. Length:. m. A profile for 0 mm board, or mm glazing or mm mirror panels. Made from aluminium alloy, anodized or finished in simulated wood paint. Colours: xx: AS, AC, AWP. Packaging: pcs/pack. Weight: ~.0 kg/pack.

40 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors System components 09xx xx 9. 9, Aluminium Stile, 0 mm. Length:. m. A profile for 0 mm board, or mm glazing or mm mirror panels. Made from anodized aluminium alloy. Colours: xx: AS, AWP. Packaging: pcs/pack. Weight: ~.0 kg/pack. 7 xx Aluminium Stile.iniowy Długość,m. Profil do wypełnienia z płyty 0mm oraz z szyby,mm lub lustra mm. Wykonany ze stopu aluminium anodowanego. Posiada specjalny kanałek pod wpuszczany pasek buforowy. Kolory: xx: AS, AC. Opakowanie: szt./opak. Waga: ~, kg/opak. Dostępność: ciągła. 00xx., Aluminium Single Bottom Track. Length: m. A track made from anodized aluminium alloy. The width of the single track enables it to be easily connected with other tracks (butt joints), providing correct distances between door leaves. Colours: xx: AS, AC, AWP. Packaging: 0 pcs/pack. Weight: ~. kg/pack. Aluminium Stile.iniowy Długość,m. Profil do wypełnienia z płyty 0mm oraz z szyby,mm lub lustra mm. Wykonany ze stopu aluminium anodowanego. Kolory: xx: AS. Opakowanie: szt./opak. Waga: ~,0 kg/opak. Dostępność: ciągła., 9 0xx, 00xx Tor dolny aluminiowy potrójny. Tor wykonany ze stopu aluminium anodowanego. Kolory: xx: AS. Opakowanie: 0 szt./opak. Waga: ~, kg/opak.., Dostępność: ciągła. 0. 0, Aluminium Single Top Track. Length: m. Aluminium Single Top Track. Length: m A track made from anodized aluminium alloy or finished in simulated wood film. The track features a shadow line which masks ceiling irregularities. Profile length: 000 mm. Colours: xx: AS, AC, AWP. Packaging: pcs/pack. Weight: ~.07 kg/pack. Availability: continuous 00xx xx,.,. 9. 9,.,, Aluminium Connector Rail, 0 mm. Length: m. A profile for 0 mm board, or mm glazing or mm mirror panels. Made from anodized aluminium alloy. Colours: xx: AS, AC, ASB, ACB, AMW, AAW, AWW, AWP. Packaging: 0 pcs/pack. Weight: ~.0 kg/pack., xx 9. 9,. Tor górny aluminiowy potrójny. Długość m. Tor wykonany ze stopu aluminium anodowanego. Tor posiada linię cienia ukrywającą optyczne nierówności sufitu. Kolory: xx: AS. Opakowanie: szt./opak. Waga: ~, kg/opak. Dostępność: ciągła.., Aluminium Connector Rail, 0 mm. Length: m. A profile for 0 mm board, or mm glazing or mm mirror panels. Made from anodized aluminium alloy. Customdesigned shape for easy bending of the profile. Colours: xx: AS, AC, ASB, ACB, AWP. Packaging: 0 pcs/pack. Weight: ~7. kg/pack.

41 7 xx Aluminium Connector Rail, mm. Length:. m. A profile for mm glass or mirror panels or for board provided with an appropriate groove. Colours: xx: AS, AC, Packaging: 00 pcs/pack. Weight: ~ kg/pack. 00xx,..,,..7,7 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors System components 0xx Decorative Strip, mm. Length: m. An x mm universal decorative profile fixed to door panels. Colours: xx: AS, AC, ASB, ACB, AMW, xx AAW, AWW, AWP. Packaging: 00 pcs/pack. Weight: ~.9 kg/pack. Aluminium Decorative Strip. Length: m. A x mm universal decorative profile fixed to door panels. Colours: xx:as, AC, ASB, ACB, AMW, AAW, AWW, AWP. Packaging: 00 pcs/pack. Weight: ~.0 kg/pack. 000xx Aluminium System Gasket, 0/ mm. Packaging: 00 m/roll Weight: ~. kg/roll Aluminium System Gasket, 0/ mm. Packaging: 00 m/roll. Weight: ~9.7 kg/roll. -. Self-adhesive Buffer Strip,.x or. x. A strip designed to dampen door impact against the wall and eliminate minor wall irregularities. Hair length: mm or mm. Colours: xx: 00 white, 0 black, brown, beige, 0 - grey Packaging: 0m/roll grey; 0 m/roll other colours. Weight: ~.90 kg/roll. Availability: continuous (white, beige, grey); other colours available to order Transparent Plug for Aluminium Profiles. A plug covering installation holes. Packaging: 00 pcs/pack. Weight: ~0.0 kg/pack xx Gasket..7 Self-adhesive Dust-stop Brush,.7 x. A brush designed to seal the space between door leaves and to stop dust. Hair length: mm. Colours: xx: 00 white, 0 black, brown, beige, 0 - grey. Packaging: 00, 0,, - 00 m/roll m/roll. Weight: 00, 0,, - ~.0 kg/roll. 0 - ~. kg/roll. Availability: continuous (white, beige, grey), other colours available to order x Aluminium System Gasket, 0/ mm. An elastic component for secure connection of mirror with a profile, fully concealed in the profile. Versions: x: K Fig. (milk). V Fig.. C Fig. (transparent). Packaging: 00 m/roll. Weight: K - ~.0 kg/roll, V - ~.90 kg/roll, C - ~. kg/roll. Fig. Fig xx.7 Self-adhesive Dust-stop Brush,.7 x. A brush designed to seal the space between door leaves and to stop dust. Hair length: mm. Colours: xx: 9 - grey. Packaging: 00 m/roll. Weight: ~. kg/roll.

42 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors System components 000xx 0xx 0, 7,7 0 Sliding Door Lock. A universal lock for steel and aluminium door systems. Colours: xx: 00 black, 0 - white Packaging: pce/pack.. Weight: ~0.0 kg/roll. 0000A. x Allen-head Self-tapping Screw. A basic fastener for the aluminium system. Packaging: 000 pcs/pack. Weight: ~.0 kg/pack. Accessories: mm Allen key xx Aluminium Recessed Single Bottom Track. Length: m. A track made from anodized aluminium alloy. Colours: xx: AS, AC, AWP. Packaging: 0 pcs/pack. Weight: ~.7 kg/pack. Availability: continuous (AS), other colours available to order. 0SU 7, Aluminium Wide Recessed Single Track. Length: m. A track made from anodized aluminium alloy. Colours: xx: AS, AC, AWP. Packaging: 0 pcs/pack. Weight: ~.0 kg/pack. Availability: continuous (AS), other colours available to order. 0,, Mounting Profile for Recessed Single Bottom Profile, for use with xx. Length: m. Colours: raw aluminium. Packaging: 90 pcs/pack. Weight: ~. kg/pack Self-adhesive Cap. Packaging: pcs/pack. Weight: ~0.0 kg/pack Self-adhesive Cap. INDECO. Packaging: pcs/pack. Weight: ~0.0 kg/pack. 0000xx Self-adhesive Safety Backing., Self-adhesive Safety Backing, 00 mm x 0 m. Transparent film. Packaging: 00 m/roll, 0 cm wide. Weight: ~.0 kg/roll Self-adhesive Safety Backing, 00 mm x 0 m. Black film. Packaging: 0 m/roll, 0 cm wide. Weight: ~.00 kg/roll Self-adhesive Safety Backing, 00 mm x 0 m. Transparent film. Packaging: 7 m/roll, 0 cm wide. Weight: ~7.0 kg/roll Self-adhesive Safety Backing, 00 mm x 0 m. Transparent film. Packaging: 00 m/roll, 0 cm wide. Weight: ~0.0 kg/roll.

43 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller sliding doors System components Aluminium Top Track Stopper. Packaging: pce/pack. Weight: ~0.0 kg/pack End Cap for Aluminium Single Top Track. Packaging: pce/pack. Weight: ~0.00 kg/pack Positioner for Aluminium Bottom Track. Comes complete with a. mm Allen key. Packaging: 0 pcs/pack. Weight: ~0.00 kg/pack End Cap for Aluminium Double Top Track. Packaging: pce/pack. Weight: ~0.0 kg/pack. Buffer Strip Clip. A clip preventing the buffer strip from coming unstuck. Color: silver. Packaging: 00 pcs/pack. Weight: ~0.0 kg/pack Aluminium Bottom Track Stopper. Packaging: pce/pack. Weight: ~0.00 kg/pack. Comes complete with. mm Allen key End Cap for Aluminium Double Bottom Track. Packaging: 0 pcs/pack. Weight: ~0.0 kg/pack. Comes complete with. mm Allen key. 0999A Buffer Strip Clip. A clip preventing the buffer strip from coming unstuck. Color: silver. Packaging: 00 pcs/pack. Weight: ~0. kg/pack x End Cap for Aluminium Double Bottom Track. x: L left, R right. Packaging: 00 pcs/pack. Weight: ~0.0 kg/pack. Comes complete with a. mm Allen key Double-sided Self-adhesive Tape, 0. mm. All-purpose assembly tape. Packaging: m/pack. Weight: ~0.7 kg/pack. 0 Aluminium System Soft Closer Accessories. The accessories include: - Trigger - Fixing screws - Adapters Application: A00, A00, Ontario. 099x >see page Universal Soft Closer.

44 ONTARIO FRAMELESS DOORS (aluminium system) Boundary conditions: - maximum dimensions of the opening: 000 mm in height (or up to 00 mm in light panel applica tions), any width with sections of up to 000 mm each. - maximum dimensions of individual doors: 70 mm in height, 00 mm in width or, for light doors not exceeding 0 kg, the door width can be increased to 000 mm and the height to 00 mm. - maximum weight of 0 kg. - panel thickness of mm.

45 7. ONTARIO FRAMELESS DOORS Components / Assembly drawing AS 70AS 70AS Wide Rail Narrow Rail Stile Top Guide with Bearing for Profiles Aluminium Narrow Top Track Frameless Door Holder and Narrow Double Bottom Track Fascia Aluminium Narrow Double Bottom Track 0000xx Buffer Strip 000xx Dust Stop Brush Strip Top Track Stopper 099 Aluminium System Universal Soft Closer Accessories 099x Universal Soft Closer 0999A Buffer Strip Clip A. x Self-tapping Screw Self-adhesive Cap 0000x Lock Plug 07 Bottom Roller (complete) 0997 Positioner 0997 Bottom Track Stopper 0999x Bottom Positioner 00009x Single Bottom Track End Cap, left/right 0xx Aluminium Single Bottom Track 0xx Alu. Recessed Wide Single Bottom Track xx Aluminium Recessed Single Bottom Track 0SU Recessed Single Bottom Track Mounting Profile

46 ONTARIO FRAMELESS DOORS Fabrication instructions Calculate door front dimensions > see page Define the number of overlaps > see page profile Calculate door leaf dimensions DW = (OW + z * ) / n overlap width min. mm DH = OH mm DH = OH 0mm for recessed tracks DH = OH mm with soft closer DH = OH mm - with soft closer and recessed tracks n number of leaves z number of overlaps Symbols used in calculations OH opening height OW opening width DW door width DH door height PW panel width PL panel length SL stile length RL rail length Cut components PW = DW mm PL = DH mm SL = DH RL = DW mm (see the section Cut rails ) Mirror protection > see page 7 Drill installation holes > see page Drill installation holes, ctd. > see page 9 7 Install connector rail > see page 9 9 Install stiles Fix stiles using double-sided self-adhesive tape or glass adhesive (Soudal FIX ALL Crystal adhesive is recommended) to the panel. Remember to carefully clean and degrease the surfaces of components to be glued. Advice: To determine the appropriate distance, put a piece of rail against the panel. When using an adhesive, wait for the adhesive to set completely before the door leaf is installed in the wardrobe. Cut rails Cut rails as shown in the drawing. A special cut in the rail eliminates the development of space between the rail and the stile, and conceals the mirror edge. DW PW 0 DH PL SL RL 9., DPP.,.,

47 ONTARIO FRAMELESS DOORS Fabrication instructions 0 Install rails Clean the cut rails with a solvent and fix them to the panel using double-sided self-adhesive tape or glass adhesive (Soudal FIX ALL Crystal adhesive is recommended). Owing to panel cutting tolerances, panel dimensions may differ slightly from the desired ones. To avoid problems, before cutting the rails, measure the distance between the stiles and cut the rails to that length. Install top guides ) Fix the screw, leaving a gap of about mm between the screw head and the profile. ) Insert the guide tongues under the head of the self-tapping screw 0000A. ) Tighten the screw, fastening the profiles and the guide together. Install the other guide likewise. Install bottom rollers > see page 9,

48 ONTARIO FRAMELESS DOORS Installation instructions Cut the tracks > see page 0 Install the top track > see page 0 Fix stoppers and positioners in the bottom track > see page 0 Install the door > see page 0 Install the bottom track > see page Adjust door position > see page Fix the top track stopper > see page Adjust the bottom stopper and top stopper> see page Fix the positioner/stopper > see page Fix the caps > see page > see page Fix the dust-stop brush strips and buffer strips > see page Fix the buffer strip clip > see page 0 Fix the decorative strips > see page Fix the dedicated decorative profile > see page Install the locks > see page Adjust the bottom positioners > see page Fix the recessed bottom tracks > see page Fix the single and double top track end cap > see page Fix the single and double bottom track end ca > see page Mount the fascia > see page Mount the universal soft closer > see page Mount the soft close trigger > see page

49 ONTARIO FRAMELESS DOORS System components 7AS Frameless Door Holder. Colour: chrome, transparent glass. Wide Rail, Anodized. Belongs to the group of profiles developed for frameless doors. Apart from the wide rail, the group consists of the stile 70 and the narrow rail 70. Application: A00B, A00B, A00B, A00B, A00B. Panel thickness: mm. Colours: AS. Length:. m Availability: Continuous. 70AS 7 70 Aluminium Narrow Double Bottom Track Fascia. 0 pcs/pack. Weight: kg/pack ,.,.7,7.,,. 9, 9. Narrow Rail, Anodized. The Ontario aluminium narrow rail belongs to the group of profiles developed for frameless doors. Apart from the narrow rail, the group consists of the stile 70 and wide rail 7. Application: A00B, A00B, A00B, A00B, A00B. Panel thickness: mm. Colours: AS. Length:. m. Availability: Continuous... 70AS Alumimium Stile, Anodized. Belongs to the group of profiles developed for frameless doors. Apart from the stile, the group consists of the narrow rail 70 and wide rail 7. Application: A00B, A00B, A00B, A00B, A00B. Panel thickness: mm. Colours: AS. Length:. m. Availability: Continuous. 000 Top Guide with Bearing for and Profiles. 00 pcs/pack. Weight:.kg. 700 Aluminium Narrow Top Track. pcs/pack. Weight ~kg/pack. 0, ,..,, Aluminium Narrow Double Bottom Track. 0 pcs/pack. Weight: 0kg/pack. 0000xx > see page 9 Self-adhesive Buffer Strip. 000xx > see page 9 Self-adhesive Dust-stop Brush.7 x > see page 0 Aluminium Top Track Stopper. 099 > see page Universal Soft Closer Accessories. 099x > see page Universal Soft Closer. 0999A > see page Buffer Strip Clip. 0000A > see page 9. x Allen-head Self-tapping Screw > see page 0 Self-adhesive Cap. 0000x > see page 9 Sliding Door Lock > see page Transparent Plug for Aluminium Profiles. 07 > see page Bottom Roller for Aluminium System > see page Positioner for Aluminium Bottom Track > see page 0 Aluminium Bottom Track Stopper. 0999x > see page Bottom Positioner x > see page Bottom Track End Cap. 0xx > see page Aluminium Single Bottom Track. 0xx > see page 0 Aluminium Wide Recessed Single Track. xx > see page 9 Aluminium Recessed Single Bottom Track. 0SU > see page 0 Recessed Single Bottom Track Mounting Profile. 7

50 ATHABASCA NARROW FRAME DOORS (aluminium system) Boundary conditions: - maximum dimensions of the opening: 000 mm in height (or up to 00 mm in light panel applications), any width with sections of up to 000 mm each. - maximum dimensions of individual doors: 70 mm in height, 00 mm in width or, for light doors not exceeding 0 kg, the door width can be increased to 000 mm and the height to 00 mm. - maximum weight of 0 kg. - panel thickness of mm or 0 mm.

51 7, 7, 0,7,7, 0, 7, 0,9 0,, ATHABASCA NARROW FRAME DOORS Components 7. 7, ,. 9.7,. Ø/9,7 /9.7,. 0, ,.,

52 ATHABASCA NARROW FRAME DOORS Components Assembly drawing x xx xx 0xx 0xx xx xx xx 0xx 00xx xx 0000xx 000xx 0000x Wózek dolny (komplet) Top Guide for and profiles Bottom Positioner Aluminium Narrow Double Bottom Track Aluminium Narrow Bottom Track Facia Aluminium Narrow Double Top Track Aluminium Rail, Narrow Aluminium Rail, Wide Aluminium Stile Aluminium Single Bottom Track Aluminium Connector Rail Aluminium Narrow Connector Rail mm Aluminium Connector Rail mm Decorative Strip Aluminium Decorative Profile Plug Gasket Buffer Strip Dust Stop Brush Strip Lock A xx 0xx 0SU xx x A x. x Self-tapping Screw Aluminium Recessed Single Bottom Track Alu. Recessed Wide Single Bottom Track Recessed Single Bottom Track Mounting Profile Self-adhesive Cap INDECO Self-adhesive Cap Safety Backing Top Track Stopper Bottom Track Stopper Single Bottom Track End Cap, left/right Double-sided Self-adhesive Tape Positioner Buffer Strip Clip Buffer Strip Clip Aluminium System Universal Soft Closer Accessories Universal Soft Closer

53 ATHABASCA NARROW FRAME DOORS Fabrication instructions Calculate door front dimensions > see page Define the number of overlaps > see page profile Calculate door leaf dimensions: Overlap width = 9 mm Door leaf width: DW = (OW + z * 9 mm) / n where: OW = opening width DW = door leaf width z number of overlaps n number of leaves Combination panels > see page 7 Mirror protection > see page Door leaf height: DH = OH DH = OH 0 (for recessed tracks) DH = OH (with soft closer) DH = OH 9 (with soft closer and recessed tracks) where: OH = opening height Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm, mirror: PW = DW mm Panel length: board: PL = DH mm, mirror: PL = DH 0 mm Rail length: RL = DW mm Stile length: SL = DH Drill installation holes > see page 7 Drill installation holes, ctd. > see page Install connector rails > see page Install stiles > see page Install rails > see page Fix top guides 000 ) Drive the screw in, leaving a gap of about mm between the screw head and the profile. ) Insert the guide tongues under the head of the self-tapping screw 0000A. ) Fasten the profiles and the guide together with the screw. Fix bottom rollers > see page 9 Structural reinforcement > see page 9 DW PW DH PL SL RL

54 ATHABASCA NARROW FRAME DOORS Installation instructions Cut the tracks > see page 0 Install the top track > see page 0 Fix stoppers and positioners in the bottom track > see page 0 Set the door in place Lay the bottom track on the floor, offsetting it from the door face (inwards) by about: x = mm for the profile. If the track is to be fitted with bottom positioners and stoppers, insert them in the respective tracks before fixing. Fully insert the door leaf in the top track, taking care not to damage the bottom rollers, then align the bottom end of the door leaf with the bottom track and slowly lower the leaf, letting the rollers snap into the tracks Advice: Before you set the door in place, put a cardboard sheet on the bottom track to prevent damage to track surface. When the door is already in position, remove the protective cardboard Install the bottom track > see page Adjust door position > see page Fix the top track stopper > see page Adjust the bottom stopper and top stopper > see page Fix the positioner/stopper > see page Fix the caps > see page Fix the dust-stop brush strips and buffer strips > see page Fix the buffer strip clip > see page 0 Fix the decorative strips > see page Install the locks > see page Adjust the bottom positioners > see page Fix the recessed bottom tracks > see page Fix the single and double top track end cap > see page Fix the single and double bottom track end cap > see page Install the fascia > see page Install the universal soft closer > see page Install the soft closer trigger > see page x

55 ATHABASCA NARROW FRAME DOORS System components > see page Bottom Roller for Aluminium System. 000 > see page 7 Top Guide with Bearing. 0999x > see page Bottom Positioner > see page 7 Aluminium Narrow Double Bottom Track. 70 > see page 7 Aluminium Narrow Bottom Track Fascia. 700 > see page 7 Aluminium Narrow Double Top Track. 0xx > see page7 Narrow Aluminium Rail, 0 mm. xx > see page7 Wide Aluminium Rail, 0 mm. 0xx Aluminium Stile, 0 mm. or, with an appropriate gasket, for mm, mm or mm panels. The profile is made from anodized aluminium alloy. A door leaf set in Athabasca stiles features a very narrow frame of mm in width. Applications: A00, A00, A00, A00, A00. Colours: AS. Length:. m. Weight: 7. kg/pack xx > see page Aluminium Single Bottom Track. xx > see page Aluminium Connector Rail. xx > see page Narrow Aluminium Connector Rail. xx > see page mm Aluminium Connector Rail. 0xx > see page mm Decorative Strip. 00xx > see page Aluminium Decorative Profile > see page Plug. 0000xx > see page 9 Gasket. 0000xx > see page 9 Self-adhesive Buffer Strip. 000xx > see page 9 Self-adhesive Dust-stop Brush. 0000x > see page 9 Sliding Door Lock. 0000A> see page 9. x Allen-head Self-tapping Screw. xx > see page 9 Recessed Single Bottom Track. 0xx > see page 0 Aluminium Wide Recessed Single Track. 0SU > see page 0 Recessed Single Bottom Track Mounting Profile > see page 0 Self-adhesive Cap > see page 0 INDECO Self-adhesive Cap. 0000xx > see page 0 Self-adhesive Safety Backing > see page 0 Aluminium Top Track Stopper > see page 0 Aluminium Bottom Track Stopper x > see page End Cap for Aluminium Double Bottom Track > see page Double-sided Self-adhesive Tape, 0. mm > see page Positioner for Aluminium Bottom Track > see page Buffer Strip Clip. 0999A > see page Buffer Strip Clip. 099 > see page Universal Soft Closer Accessories. 099x > see page Universal Soft Closer.

56 A00 SERIES SLIDING DOORS (aluminium system) bottom roller slant sliding doors Boundary conditions: - maximum dimensions of the opening: 000 mm in height (or up to 00 mm in light panel applications with reinforcement), any width with sections of up to 000 mm each. - maximum dimensions of individual doors: 70 mm in height, 00 mm in width or, for light doors not exceeding 0 kg, the door width can be increased to 000 mm and the height to 00 mm. - maximum weight of 0 kg. - panel thickness of mm or 0 mm. - the characteristic feature of the system is its suitability for slant doors.

57 . INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller slant sliding doors 7. Basic dimensions 9. * Ø/9.7 Ø.. 0* Ø. Ø Ø. Ø

58 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller slant sliding doors Elementy składowe Assembly drawing xx 0xx 0999x 000xx 0xx 00xx 0xx xx 0xx 0xx 0xx 0xx xx 00xx 0xx 00xx 00xx 00xx xx xx xx 0xx 00xx Bottom Roller Top Guide with Bearing for profiles Top Guide with Bearing for profiles Bottom Positioner Aluminium Double Bottom Track Aluminium Bottom Track Facia Aluminium Double Top Track Aluminium Rail, Narrow Aluminium Rail, Wide Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Single Bottom Track Aluminium Triple Bottom Track Aluminium Single Top Track Aluminium Triple Top Track Aluminium Connector Rail Narrow Aluminium Connector Rail mm Aluminium Connector Rail mm Decorative Strip Aluminium Decorative Profile Block Angle Connector Angle Connector L 9000LD x xx 0000xx 000xx 0000x 0000A xx 0xx 0SU xx x A A00/A00 System Guide with Bearing A00/A00 System Guide with Bearing, long A00/A00 System Guide Track Guide Track End Cap Soft Close Damper Plug Gasket Buffer Strip Dust Stop Brush Strip Lock. x Self-tapping Screw Aluminium Recessed Single Bottom Track Alu. Recessed Wide Single Bottom Track Recessed Single Bottom Track Mounting Profile Self-adhesive Cap INDECO Self-adhesive Cap Safety Backing Top Track Stopper Single Top Track End Cap Double Top Track End Cap Bottom Track Stopper Double Bottom Track End Cap Single Bottom Track End Cap, left/right Double-sided Self-adhesive Tape Positioner Buffer Strip Clip Buffer Strip Clip

59 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller slant sliding doors Instrukcja wykonawcza Calculate door front dimensions > see page Define the number of overlaps > see page Note: Slant door leaves are intended for systems with not more than two slant leaves on one side, one of which must only have a slant corner. 7 9 profile. Calculate door leaf dimensions > see page profile. Calculate door leaf dimensions > see page profile. Calculate door leaf dimensions > see page Profil Oblicz wymiary skrzydeł drzwi > patrz str. Combination panels > see page 7 Mirror protection > see page Slant-corner leaf Cut the profiles to the right dimensions and at correct angles. Use the angle connector for profile joints. 0 Advice: Remember that the stiles forming the slant side must be cut at half the leaf slant angle. To obtain a 0-degree angle, cut the profiles at the joint at 0 degrees. Leaf with slant upper part Cut the profiles to the right dimensions and at correct angles. The slant angle should be within the º to º range. Use two angle connectors for profile joints. Advice: Remember that the stiles forming the slant side must be cut at half the leaf slant angle. To obtain a 0-degree angle, cut the profiles at the joint at 0 degrees. Drill installation holes Prior to leaf assembly, drill /9.7 mm holes in each stile. They will be used to fix: Hole A: the top rail and the top guide with a self-tapping screw, and to fix and adjust the bottom wheel with a bolt. Hole B: the bottom rail with a self-tapping screw. Preferably, drill the holes using the subland drill 0000 and the drill jig for aluminium profiles or Drill jig is intended for making holes with a hand-held drill, while drill jig 0000 is designed for making holes by means of a bench drill. Both jigs are all-purpose devices, and can be used for drilling holes in all types of stiles. 7 Install connector rails > see page A B A 0000 A 0 B

60 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller slant sliding doors Fabrication Instructions Install stiles Put one end of the stile against the corresponding end of the panel and tap the stile in place using a rubber mallet along the entire length, so that it protrudes as desired at both ends of the panel. Fix the other stile likewise. Before fitting the stiles to the slant side, use the angle connector for the profile and for the. profile. Push the angle connector in position into the connected stiles and then fix the panel or mirror with a gasket in the profiles. The angle connector is designed to be inserted tightly into the stiles. If the panel sits loosely in the profiles or if there is play at the angle connector stile joint, it is necessary to fasten both stiles to the connector with screws. Drill a. mm hole in the back wall of the profile (for a profile, ream the hole in the outside wall with a 9 mm bit) mm from the joint edge. Use. x screws Advice; To determine an appropriate protrusion, put a piece of rail against the panel. For a mirror, exercise special care when you start fixing the stile. Before fixing the stile to the mirror, fit the gasket in one piece. Start attaching the gasket from the centre of the upper edge of the mirror. Make a cut in the outer side of the gasket at each corner of the mirror, using a sharp knife. When fitting the gasket, make sure it is slightly stretched. Where the door is to be provided with a panel composed of several different materials, join all the materials together before fixing the stiles. 7 9 Install rails > see page Fix symmetrical top guides > see page Fix non-symmetrical top guides > see page Install the guide on the slant end When fixing the guide to the rail on the slant end, bend the guide tongues beforehand at an appropriate angle so that the wheels travel horizontally after the roller is installed. Fix bottom rollers > see page 9 Structural reinforcement > see page 9 7

61 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller slant sliding doors Installation Instructions Cut the tracks > see page 0 Install the top track > see page 0 Fix stoppers and positioners in the bottom track > see page 0 Install the door > see page 0 Install the bottom track > see page 0 Leaf with a slant upper part guide track installation Cut the guide track 0000 at least 0 mm longer than the door leaf width. The length of the guide track should allow the leaf to be moved fully to the side. Drill mm holes in the guide rail at 0 cm centres. Fix the guide track to the shelf with screws. Make sure the guide track is precisely in a horizontal position and parallel to the bottom track this will ensure correct operation of the door. Prior to final fastening of the screws, attach caps to the guide track. Advice: To ensure a wide range of movement of the slant door leaf, the guide track may extend across the entire width of the system. 7 9 Adjust door depth The leaf depth adjustment range, measured from the face of the wardrobe interior, with the guide track mounted on the shelf is - mm. If the guide rail is mounted under the shelf, the adjustment range is - mm. To adjust the guide, cut its stem to the desired length. Fix the guide track end cap Caps can be applied to double and single top tracks if the tracks are shorter than the width of the opening or they are installed outside the opening fitted with sliding doors. Fix the guide bracket To determine the place for fixing the guide bracket: ) Put a level on the shelf and draw a line directly under the level. ) Move the guide down, away from the line drawn by the distance of: x= when fixing the track to the shelf edge, x= when fixing the track under the shelf. ) Fasten the guide with the screws supplied in the package. Door height can be adjusted within the range of ±9 mm X

62 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller slant sliding doors Installation Instructions 0 Leaf with a slant upper part leaf installation For safety reasons, a leaf with a slant upper part must be installed on the internal side of the system (in the inner track). Fix the guide to the inner side of the stile so that the guide rollers are situated in the middle of the guide track height. Set the guide rollers horizontally, adjusting its position with screws on the sleeve. Set the door in the inner track Adjust door position > see page Fix the end caps > see page Install the locks > see page Fix the dust-stop brush strips and buffer strips > see page Fix the buffer strip clip > see page 0 Fix the decorative profiles > see page Adjust the bottom positioners > see page Fix the positioner/stopper > see page Fix the recessed bottom tracks > see page Mount the universal soft closer > see page Mount the universal soft closer trigger > see page Fix the single or double top track end cap > see page Fix the single and double bottom track end cap > see page Mount the fascia > see page 0

63 INDECO A00 SERIES ALUMINIUM SYSTEM bottom roller slant sliding doors System Components > see page Bottom Roller for Aluminium System. 07xx > see page Top Guide. 0xx > see page Top Guide. 0999x > see page Bottom Positioner. 000xx > see page Alu.Double Bottom Track. 0xx > see page Track Fascia. 00xx > see page Alu. Double Top Track. 0xx > see page 7 Narrow Aluminium Rail. xx > see page 7 Wide Aluminium Rail. 0xx > see page 7 Aluminium Rail. xx > see page Aluminium Connector Rail. xx > see page Aluminium Connector Rail. 0xx > see page mm Decorative Strip. 00xx > see page Aluminium Decorative Profile Block Expander element for the aluminium system. Packaging: pce/pack. Weight: 0.0 kg/pack xx > see page 7 Aluminium Rail. 0xx > see page 7 Aluminium Rail. 0xx > see page 7 Aluminium Rail. xx > patrz str. Aluminium Rail. 00xx > patrz str. Aluminium Rail. 0xx > patrz str. Alu. Single Bottom Track. 00xx > patrz str. Alu. Triple Bottom Track. 00xx > patrz str. Aluminium Single Top Track. 00 xx > patrz str. Aluminium Triple Top Track. xx > patrz str. Aluminium Connector Rail. Angle Connector for. aluminium profiles. An internal connector linking profiles at any angle. Aluminium casting. Packaging: pce/pack. Weight: 0.0 kg/pack Angle Connector for.aluminium profiles. An internal connector linking profiles at any angle. Aluminium casting. Packaging: pce/pack. Weight: 0.0 kg/pack A00/A00 System Track Universal End Cap. Packaging: 0 pcs/pack. Weight: ~0.0 kg/pack. 099x > see page Universal Soft Closer LD 9 A00/A00 Guide for Guide Track 0000B. Packaging: set. Weight: ~0.09 kg/pack B > see page Transparent Plug. 0000xx > see page 9 Gasket. 0000xx > see page 9 Self-adhesive Buffer Strip. 000xx > see page 9 Self-adhesive Dust-stop Brush. 000xx > see page 9 Sliding Door Lock. 0000A > see page 9 Self-tapping Screw. xx > see page 9 Recessed Single Bottom Track. 0xx > see page 0 Wide Recessed Single Track. 0SU > see page 0 Track Mounting Profile. 9000L A00/A00 Guide for Guide Track 0000B. Packaging: set. Weight: ~0.09 kg/pack. 7, Slant Door System Guide Track. Length: m. Colours: AS. Packaging: 0pcs/pack.. Weight: ~9.0 kg/pack > see page > see page 0 Self-adhesive Cap. 0000xx > see page 0 Folia zabezpieczająca > see page 0 Aluminium Top Track Stopper > see page 0 End Cap for Aluminium Single Top Track > see page 0 End Cap for Aluminium Double Top Track > see page 0 Bottom Alu.Track Stopper > see page 0 End Cap for Aluminium Double Top Track x > see page End Cap for Aluminium Double Bottom Track > see page Double-sided Self-adhesive Tape > see page Positioner for Alum Bottom Track > see page Buffer Strip Clip A > see page Buffer Strip Clip..

64 INDECO A00 SERIES ALUMINIUM SYSTEM walk-through sliding doors without thresholds Boundary conditions: - maximum dimensions of the opening: 000mm in height (for applications with light panels - up to 000mm); width up to 00mm (for two sliding leaves). - maximum dimensions of individual doors: 000mm in height, 00mm in width. - maximum weight of 0kg. - panel thickness of mm and 0mm.

65 INDECO A00 SERIES ALUMINIUM SYSTEM walk-through sliding doors without thresholds Basic Dimensions Ø M. Ø... M 7. Ø Ø Ø/Ø Ø

66 INDECO A00 SERIES ALUIMINIUM SYSTEM walk-through sliding doors without thresholds Components 0 / / 9 / / / Assembly drawing xx 0xx 0xx 0AS 0xx 0xx 0xx 07xx 07xx 09xx xx 00xx xx xx xx 0xx xx Aluminium Bottom Rail Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Connector Rail Suspended Top Track Aluminium Decorative Strip Narrow Aluminium Connector Rail mm Aluminium Connector Rail mm Decorative Strip Plug Gasket / / / / / ZL 0000A 0000xx 000xx 0xx x 0000xx A 0AS A00/A00/A00 Hardware Set Roller Roller Mounting Block Positioner PAD Guide Self-tapping Screw. x Self-tapping Screw Buffer Strip Dust-stop Brush Top Suspended Track Fascia Top Suspended Track End Cap Self-adhesive Cap INDECO Self-adhesive Cap Lock Safety Backing Double-sided Self-adhesive Tape Buffer Strip Clip Buffer Strip Clip Suspended Track Holder Fascia Suspended Track Holder

67 INDECO A00 SERIES ALUIMINIUM SYSTEM walk-through sliding doors without thresholds Fabrication Instructions Calculate door front dimensions > see page Define the number of door leaves Define the number of door leaves. n = number of leaves profile Calculate door leaf dimensions Door leaf width: DW = (OW + mm) / n where: OW = opening width DW = door leaf width n number of leaves Door leaf height: DH = OH 0 for internal doors DH = OH + mm for external doors where: OH = opening height Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm, mirror: PW = DW 9 mm Panel length: board: PL = DH 9 mm, mirror: PL = DH 9 mm Rail length: RL = DW mm Stile length: SL = DH profile Calculate door leaf dimensions Door leaf width: DW = (OW + mm) / n where: OW = opening width DW = door leaf width n number of leaves Door leaf height: DH = OH 0 for internal doors DH = OH + mm for external doors where: OH = opening height Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm, mirror: PW = DW mm Panel length: board: PL = DH 9 mm, mirror: PL = DH 9 mm Rail length: RL = DW 0 mm Stile length: SL = DH Advice: For combination panels (board/board or board/mirror), reduce the board dimension by mm and mirror dimension by mm per joint. profile Calculate door leaf dimensions Door leaf width: DW = (OW + mm) / n where: OW = opening width DW = door leaf width n number of leaves Door leaf height: DH = OH 0 for internal doors DH = OH + mm for external doors where: OH = opening height Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm, mirror: PW = DW mm Panel length: board: PL = DH 9 mm, mirror: PL = DH 9 mm Rail length: RL = DW mm Stile length: SL = DH DW PW n= 7 n= DH PL SL n= RL

68 INDECO A00 SERIES ALUMINIUM SYSTEM walk-through sliding doors without thresholds Fabrication Instructions profile Calculate door leaf dimensions Door leaf width: DW = (OW + mm) / n where: OW = opening width DW = door leaf width n number of leaves Door leaf height: DH = OH 0 for internal doors DH = OH + mm for external doors where: OH = opening height Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm, mirror: PW = DW mm Panel length: board: PL = DH 9 mm, mirror: PL = DH 9 mm Rail length: RL = DW 7 mm Stile length: SL = DH 7 l profile Calculate door leaf dimensions Door leaf width: DW = (OW + mm) / n where: OW = opening width DW = door leaf width n number of leaves Door leaf height: DH = OH 0 for internal doors DH = OH + mm for external doors where: OH = opening height Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm, mirror: PW = DW mm Panel length: board: PL = DH 9 mm, mirror: PL = DH 9 mm Rail length: RL = DW mm Stile length: SL = DH profile Calculate door leaf dimensions Door leaf width: SD = (SO + ) / n where: OW = opening width DW = door leaf width n number of leaves Door leaf height: DH = OH 0 for internal doors DH = OH + mm for external doors where: OH = opening height Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm, mirror: PW = DW mm Panel length: board: PL = DH 9 mm, mirror: PL = DH 9 mm Rail length: RL = DW mm Stile length: SL = DH 9 0 Combination panels > see page 7 Mirror protection > see page Drill installation holes Prior to leaf assembly, drill /9.7 mm holes in each stile. They will be used to fix: Hole B: the bottom rail with a self-tapping screw. Hole C: the block to the stile in suspended, pivoted and folding doors. Preferably, drill the holes using the subland drill 0000 and drill jig for aluminium profiles or Drill installation holes, ctd. Drill jig is intended for making holes with a hand-held drill, while drill jig 0000 is designed for making holes by means of a bench drill. Both jigs are all-purpose devices, and can be used for drilling holes in all types of stiles. Advice: For heavy doors of 0 0 kg, drill additional hole to fix blocks in the bottom rail hole B B C hole C B B C

69 INDECO A00 SERIES ALUMINIUM SYSTEM walk-through sliding doors without thresholds Fabrication Instructions Install connector rails Put one end of the connector rail against the corresponding end of the panel joint. Use a rubber mallet to tap the rail profile in place along the entire panel width. Then carefully tap the other part of the panel into the rail. A panel joint may be curved. In order to obtain the desired shape of the connector rail, use the profile bending tool Lift the handle, insert the profile under the bearings and gently bend the profile with the handle. Lock the handle in position with the dowel pin. Turn the crank to bend the profile over a desired length. Repeat the cycle until the desired bend radius is obtained. Advice: Owing to panel (mirror, glass or laminated board) cutting tolerances, panel dimensions may differ slightly from the desired ones. Cut the bent connector rails to the desired dimensions only after you have produced the required shape. Avoid sharp bending to make sure the anodized coat remains undamaged. Install stiles Put one end of the stile against the corresponding end of the panel and tap the stile in place using a rubber mallet along the entire length, so that it protrudes as desired at both ends of the panel. Fix the other stile likewise. Advice: To determine an appropriate protrusion, put a piece of rail against the panel. For a mirror, exercise special care when you start fixing the stile. Tap the stile carefully in position on the panel. Before fixing the stile, fit the gasket in one piece. Start attaching the gasket from the centre of the upper edge of the mirror. Make a cut in the gasket at each corner of the mirror, using a sharp knife. When fitting the gasket, make sure it is slightly stretched. Where the doors are to be provided with panels composed of several different materials, join all the materials together before fixing the stiles. Install rails Before installing the rails, insert the blocks / in the rails (see the assembly drawing). Put one end of the rail against the stile. Use a rubber mallet to tap the rail in place along the entire length. Advice: Owing to panel (mirror, glass or laminated board) cutting tolerances, panel dimensions may differ slightly from the desired ones. To avoid problems, before cutting the rails, measure the distance between the stiles and cut the rails to that length. Structural reinforcement In order to reinforce the door leaf structure with combination panels, you can optionally fix the connector rail to the stiles with self-tapping screws 0000A. Advice: Before tapping the stile onto the panel, drill screw holes for additional fixing of the connector rail using a subland drill

70 INDECO A00 SERIES ALUMINIUM SYSTEM walk-through sliding doors without thresholds Installation Instructions Cut the top track Carefully measure the width of the opening at the top and reduce the length measured by about - mm. Measure off the required track length. Use a fine-toothed metal cutting saw to cut off the redundant part of the tracks. Advice: The track to be installed should be about 0 mm longer than the width of the opening. This spare length will make it possible to avoid measurement errors and it is easy to trim. Install the top track Before fixing the top track, insert the rollers and the positioner into the track. Fix the top track with screws, offsetting its face by 9 mm. Advice: Avoid applying excessive force when tightening screws to prevent track deformation. Use cheese-head screws for best result. The surface to which the track is fixed must not be curved. Note: Before inserting the rollers, clean the inside of the suspended top track of any dirt that might accumulate during its installation Mount the top track to the wall Insert the top suspended track holder onto the suspended track. Fasten it against the track with an M set screw. The spacing of holders on the track must not be greater than 00mm to prevent track deformation during use. Fix the prepared track assembly to the wall with appropriate screws (the dimension of the fixing screw hole is.mm). For aesthetic finish, a suspended track holder fascia 0AS can be used or a furniture board fascia can be mounted on the holders. 9 Uchwyt Suspended toru podwieszanego track holder Wkręt Fxing mocujący screw Wkręt Set dociskowy screw Tor Suspended podwieszany track 00 MAX 00 mm

71 INDECO A00 SERIES ALUMINIUM SYSTEM walk-through sliding doors without thresholds Installation Instructions Install the suspended track holder fascia Install the fascia after the suspended track with holders has been mounted to the wall. The fascia fits only a suspended track with holders. Press the fascia onto the suspended track holders. Install the guide Determine a plane running vertically along the centre of the top rail (e.g. using a plumb line). Fix the guide to the floor. Set the door in place Put the door on the floor so that it engages the guide and stand it upright under the top rail. Screw the axles of the rollers 9- into the roller fixing blocks 9- until the leaf is lifted. Advice:Exercise special care when installing the doors. This operation should be performed by two persons. 7 Adjust door position Close the door and adjust the top roller axles so that the door is plumb when closed. By screwing in the axles, the door-tofloor height can be adjusted between 0 and 0 mm. Fix the positioner Having closed the door, move the positioner to a position in which the positioner tongue engages the top roller recess. Mark the position and adjust the door by fastening the positioner with the door open. Advice: You can also use the positioner to determine the door position with the door open. Suspended track holder fascia 0AS 9 Suspended track holder

72 INDECO A00 SERIES ALUMINIUM SYSTEM walk-through sliding doors without thresholds Installation Instructions 9 Fix the caps Having installed and adjusted the door leaves, cover all installation holes by inserting the plugs or by sticking the caps or Fix the brush strips and buffer strips To ensure good adhesion of the brush strips to the profiles, gently clean the profiles with alcohol or white spirit. Fix the strips, working your way from top to bottom. Cut off excess strip. For the profiles, use a shorter mm strip For other profiles, use a longer mm strip Fix the buffer strip clip > see page 0 Install the suspended top track fascia Cut the suspended top track fascia to the required length. Insert the fascia rib into the pocket on the upper edge of the track and press the lower side of the fascia so that it snaps into place on the top track. Fix the suspended top track end cap Suspended top tracks can be fitted with end caps if the tracks are shorter than the width of the opening or they are installed outside the opening fitted with sliding doors. Use a knife to cut off the redundant part of the cap on the desired side. Before finally fastening the track fixing screws, insert the cap tabs between the track and the ceiling. Then fasten the track fixing screws

73 INDECO A00 SERIES ALUMINIUM SYSTEM walk-through sliding doors without thresholds System Components xx > see page 7 Wide Aluminium Rail. 0xx > see page 7 Aluminium Stile. 0xx > see page 7 Aluminium Stile. 0AS > see page Aluminium Stile. 0xx > see page 7 Aluminium Stile. 0xx > see page 7 Aluminium Stile. 07xx > see page 7 Aluminium Stile. 09xx > see page Aluminium Stile. xx > patrz str. Aluminium Stile. 00xx > patrz str. Aluminium Stile. xx > see page Aluminium Connector Rail Aluminium Suspended Top Track. Length: m. 0 A universal profile for aluminium top roller systems. Accessories: fascia 0xx. Colours: AS. Packaging: pcs/pack. Weight: ~.7 kg/pack. Availability: continuous. 00xx > see page Aluminium Decorative Profile. xx > see page 0 mm Aluminium Connector Rail. 0AS 7 xx > see page mm Aluminium Connector Rail. 0xx > see page mm Decorative Strip > see page Transparent Plug for Aluminium Profiles xx > see page Gasket. 9000ZL 0000A > see page 9. x Allen-head Self-tapping Screw. 0000xx > see page 9 Self-adhesive Buffer Strip. 000xx > see page 9 Self-adhesive Dust-stop Brush,.7 x. 0xx Fascia for Aluminium Suspended Top Track 00SA Length: m. Colours: AS, AC, AWP. Packaging: 0 pcs/pack. Weight: ~9. kg/pack End Cap for Suspended Track. Packaging: pce/pack. Weight: ~0.00 kg/pack > see page 0 Self-adhesive Cap. 000xx > see page 9 Sliding Door Lock xx > see page 0 Self-adhesive Safety Backing > see page Double-sided Self-adhesive Tape, 0. mm > see page Buffer Strip Clip. 0999A > see page Buffer Strip Clip. Suspended Top Track Holder Fascia. Length: m. A fascia made of anodized aluminium alloy. Available colours: AS. Availability: Continuous A00/A00/A00 Roller Set A hardware set for top-roller aluminium systems. Twin-bearing rollers. Accessories: mm spanner 90009, /0 mm spanner Packaging: set. Weight: ~0. kg/pack. Suspended Track Wall Mount Holder. Available colours: AS Application: Suspended Track. Length: 7mm. Availability: Continuous.

74 INDECO A00 SERIES ALUMINIUM SYSTEM pivoted doors Boundary conditions: - maximum dimensions of the opening: 000 mm in height; width up to 00 mm (for two pivoted doors). - maximum dimensions of a pivoted door leaf: 000 mm in height, 00 mm in width. - maximum weight of kg. - panel thickness of mm or 0 mm.

75 ,,7, 0,7 7,, 9,,,,,, 7,, 0,7, 7,,7,, INDECO A00 SERIES ALUMINIUM SYSTEM pivoted doors Basic Dimensions 7.,..,, , M., 7,.. Ø/9,7 /9.7. Ø/9,7 /9.7,, ,. 70 0

76 INDECO A00 SERIES ALUMINIUM SYSTEM pivoted doors Components / 0/ 0/ / / 9-7 / 7 0/ / 0 Assembly drawing xx 0xx 0xx 0xx 0xx 0xx 0xx 07xx 07xx 09xx xx 00xx xx xx xx 0xx xx Aluminium Rail, Wide Aluminium Rail, Narrow Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Connector Rail Narrow Alu. Connector Rail mm Alu. Connector Rail mm Decorative Strip Aluminium Decorative Profile Cap Gasket 0 / / / / / / 0/ 0/ 0000xx PBuffer Strip 000xx Dust-stop Brush A00 Hardware Set - Bottom Pivot Socket - Top Pivot Socket - Top Pivot Pin Block - Bottom Pivot Pin Block -. x Self-tapping Screw 0000A. x Self-tapping Screw 0000 Magnetic Latch with Keeper Self-adhesive Cap 0000 INDECO Self-adhesive Cap 0000xx Safety Backing Double-sided Self-adhesive Tape 0999 Buffer Strip Clip 0999A Buffer Strip Clip 9000 A00 Hardware Set - Pivot with Socket - Pivot Base - Pivot with Socket

77 INDECO A00 SERIES ALUMINIUM SYSTEM pivoted doors Fabrication Instructions Calculate door front dimensions> see page Define the number of door leaves> see page profile Calculate door leaf dimensions Door leaf width: n = ( leaf) DW = OW n = ( leaves) DW = (OW 0) / Door leaf height: DH = OH With the use of the narrow rail: n = ( leaf) DW = OW n = ( leaves) DW = (OW 0) / Door leaf height: DH = OH Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm; mirror: PW = DW 9 mm Panel length: board: PL = DH 9 mm; mirror: PL = DH 9 mm Rail length: RL = DW mm Stile length: SL = DH Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm; mirror: PW = DW 9 mm Panel length: board: PL = DH mm; mirror: PL = DH mm Rail length: RL = DW mm Stile length: SL = DH profile Calculate door leaf dimensions Door leaf width: n = ( leaf) DW = OW n = ( leaves) DW = (OW 0) / Door leaf height: DH = OH Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm; mirror: PW = DW mm Panel length: board: PL = DH 9 mm; mirror: PL = DH 9 mm Rail length: RL = DW 0 mm Stile length: SL = DH Advice: For combination panels (board/board or board/mirror), make calculations in accordance with the Combination panels section in system A00. With the use of the narrow rail: n = ( leaf) DW = OW n = ( leaves) DW = (OW 0) / Door leaf height: DH = OH Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm; mirror: PW = DW mm Panel length: board: PL = DH mm; mirror: PL = DH mm Rail length: RL = DW 0 mm Stile length: SL = DH 7 Advice: In the case of combination panels (board/board or board/mirror), reduce the dimension by mm for a board or by mm for a mirror at each joint. Where buffer strips are used, reduce the door leaf width DW by mm for each strip. profile Calculate door leaf dimensions Door leaf width: n = ( leaf) DW = OW n = ( leaves) DW = (OW 0) / Door leaf height: DH = OH With the use of the narrow rail: n = ( leaf) DW = OW n = ( leaves) DW = (OW 0) / Door leaf height: DH = OH Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm; mirror: PW = DW mm Panel length: board: PL = DH 9 mm; mirror: PL = DH 9 mm Rail length: RL = DW 7 mm Stile length: SL = DH Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm; mirror: PW = DW mm Panel length: board: PL = DH mm; mirror: PL = DH mm Rail length: RL = DW 7 mm Stile length: SL = DH DW PW DH PL SL RL

78 INDECO A00 SERIES ALUMINIUM SYSTEM pivoted doors Fabrication Instructions profile Calculate door leaf dimensions Door leaf width: n = ( leaf) DW = OW n = ( leaves) DW = (OW 0) / Door leaf height: DH = OH With the use of the narrow rail: n = ( leaf) DW = OW n = ( leaves) DW = (OW 0) / Door leaf height: DH = OH Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm; mirror: PW = DW mm Panel length: board: PL = DH 9 mm; mirror: PL = DH 9 mm Rail length: RL = DW mm. Stile length: SL = DH Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm; mirror: PW = DW mm Panel length: board: PL = DH mm; mirror: PL = DH mm Rail length: RL = DW mm, Stile length: SL = DH 7 7 profil Calculate door leaf dimensions Door leaf width: n = ( leaf) DW = OW n = ( leaves) DW = (OW 0) / where: OW = opening width DW = door leaf width n number of leaves With the use of the narrow rail: n = ( leaf) DW = OW n = ( leaves) DW = (OW 0) / Door leaf height: DH = OH Door leaf height: DH = OH mm where: OH = opening height Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm; mirror: PW = DW mm Panel length: board: PL = DH 9 mm; mirror: PL = DH 9 mm Rail length: RL = DW mm. Stile length: SL = DH Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm; mirror: PW = DW mm Panel length: board: PL = DH mm; mirror: PL = DH mm Rail length: RL = DW mm, Stile length: SL = DH 9 Combination panels > see page 7 Mirror protection > see page 0 Drill installation Zamontuj holes profile łączące > see page Prior to leaf assembly, drill /9.7 mm holes in each stile. They will be used to fix: Hole B: the Zamontuj bottom rail profile with a pionowe self-tapping > see screw. page Hole C: the block to the stile in suspended, pivoted and folding doors. Preferably, Zamontuj drill the holes profile using poziome the subland > see page7 drill 0000 and the drill jig for aluminium profiles or Drill installation Wzmocnienie holes, ctd. konstrukcji > see page7 Drill jig is intended for making holes with a hand-held drill, while drill jig 0000 is designed for making holes by means of Uwaga a bench > see drill. page Both jigs are all-purpose devices, and can be used for drilling holes in all types of stiles. Install connector rails > see page Install stiles > see page hole B Install rails > see page Structural reinforcement > see page 9 B C hole C C B B C

79 INDECO A00 SERIES ALUMINIUM SYSTEM pivoted doors Installation Instructions Install pivot sockets Insert and fix the bottom pivot bracket with screws at a distance y from the wall, offsetting it inwards from the door face by x : х = 0 mm for the profiles х = 7 mm for the profiles y = mm for the profiles y = 9 mm for the profiles y = 9 mm for the profiles y = mm for the profiles Advice: When fixing the pivot socket, set the screws at the centres of the oblong holes, which will enable you to adjust the position in both directions. Set the door in place Rest the door on the bottom pivot socket, putting it upright, and turn the top pivot socket. Then unscrew the bottom pivot pin, so that the door rises and fits tightly against the top pivot socket. Use a level to plumb the door and reposition the top pivot socket if necessary. Advice: Exercise special care when setting the door in place. This operation should be performed by two persons. 7 Adjust the door Door-to-floor clearance can be adjusted between 0 and 0 mm by screwing the pivot pins in or out. Fix the magnetic latch > see page Fix the caps > see page Fix the brush strips and buffer strips To ensure good adhesion of the brush strips to the profiles, gently clean the profiles with alcohol or white spirit. Fix the strips, working your way from top to bottom. Cut off excess strip. Fix the buffer strip clip > see page 0 Fix the decorative profiles> see page 77 x Y 90

80 INDECO A00 SERIES ALUMINIUM SYSTEM pivoted doors System Components 7 9 xx > see page 7 Wide Aluminium Rail. 0xx > see page 7 Narrow Aluminium Rail. 0xx > see page 7 Aluminium Stile. 0xx > see page 7 Aluminium Stile. 0xx > see page 7 Aluminium Stile. 0xx > see page 7 Aluminium Stile. 07xx > see page 7 Aluminium Stile A00 Hardware Set for aluminium systems with A00 hinged doors. For wide rails. Accessories: mm spanner Packaging: set. Weight: ~0./set xx > see page Aluminium Stile. xx > patrz str. Aluminium Stile. 00xx > patrz str. Aluminium Stile. xx > see page 0 mm Aluminium Connector Rail. xx > see page 0 mm Aluminium Connector Rail. xx > see page mm Aluminium Connector Rail. 0xx > see page mm Decorative Strip xx > see page Aluminium Decorative Profile > see page Transparent Plug for Aluminium Profiles xx > see page 9 Gasket xx > see page 9 Self-adhesive Buffer Strip. 0000xx > see page 9 Self-adhesive Dust-stop Brush,.7 x. 0000A > see page 9. x Allen-head Self-tapping Screw > see page Magnetic Latch > see page Self-adhesive Cap. 0000xx > see page 0 Self-adhesive Safety Backing > see page Double-sided Self-adhesive Tape > see page Buffer Strip Clip A > see page Buffer Strip Clip A00 Hardware Set for aluminium systems with A00 hinged doors. For narrow rails. Packaging: set. Weight: ~0.0 kg/set.

81 INDECO A00 SERIES ALUMINIUM SYSTEM folding doors Boundary conditions: - maximum dimensions of the opening for the folding system: 000 mm in height and 000 mm in width (for double bi-fold doors). - maximum dimensions of a bi-fold door: 000 mm in height, 000 mm in width (two leaves of 00 mmm each). - maximum weight of kg. - panel thickness of mm or 0 mm.

82 ,7, 9, 0* * 7,,7, 9,7 0,7 0,7 Ø/9,7 Ø M,,,, M, 9, 0, Ø M,, Ø, 0 M, 0 INDECO A00 SERIES ALUMINIUM SYSTEM folding doors Basic Dimensions /

83 INDECO A00 SERIES ALUMINIUM SYSTEM folding doors Components / / / 0 / /7 / 0 / / 9 / / /9 Assembly drawing / / xx 0xx 0xx 0xx xx xx xx xx 0xx xx xx 900xx 90000ZL Aluminium Rail, Wide Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Connector Rail Narrow Aluminium Connector Rail mm Aluminium Connector Rail mm Decorative Strip Suspended Top Track Suspended Top Track End Cap Aluminium Decorative Profile Plug Gasket Hinge A00 Hardware Set - Top Pivot Socket - Top Pivot Pin Block / / / / /7 / /9 /0 / A 0xx xx xx A 0AS Bottom Pivot Pin Block - Bottom Pivot Socket - Roller - Roller Mounting Block - Positioner - Locating Screw Block - Locator -. x Self-tapping Screw - Toothed Spring Washer. x Self-tapping Screw Suspended Top Track Fascia Self-adhesive Cap INDECO Self-adhesive Cap Protective Backing Double-sided Self-adhesive Tape Buffer Strip Buffer Strip Clip Buffer Strip Clip Suspended Track Holder Facia Suspended Track Holder

84 INDECO A00 SERIES ALUMINIUM SYSTEM folding doors Fabrication Instructions Calculate door front dimensions > see page Define the number of door leaves Define the number of single door leaves fixed to one top track. n number of leaves profile Calculate door leaf dimensions Door leaf width: n = ( leaves) DW = (OW 0) / n = ( leaves) DW = (OW ) / n = ( leaves) DW = (OW ) / Door leaf height: DH = OH mm Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm mirror: PW = DW 9 mm Panel length: board: PL = DH 9 mm mirror: PL = DH 9 mm Rail length: RL = DW mm Stile length: SL = DH profile Calculate door leaf dimensions Door leaf width: n = ( leaves) DW = (OW 0) / n = ( leaves) DW = (OW ) / n = ( leaves) DW = (OW ) / Door leaf height: DH = OH mm Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW mm mirror: PW = DW mm Panel length: board: PL = DH 9 mm mirror: PL = DH 9 mm Rail length: RL = DW 0 mm Stile length: SL = DH Advice: For combination panels (board/board or board/mirror), make calculations in accordance with the Combination panels section in system A Combination panels > see page 7 Mirror protection > see page Drill installation holes > see page 7 Install connector rails > see page Install stiles > see page Install rails > see page 7 Structural reinforcement > see page 9 DW PW DH PL SL RL

85 INDECO A00 SERIES ALUMINIUM SYSTEM folding doors Fabrication Instructions Connect the leaves Insert the caps and lay both leaves next to each other with the back facing upwards, so that the caps abut. Use a power screwdriver to fix the hinges 900xx to both leaves, providing for a distance of about 0 mm from the stile ends. Two hinges can be used for door heights of less than 00 mm. To fix the hinges, use.9 x self-tapping screws Advice: Make sure that the door leaves abut tightly when fixing the hinges. This will guarantee smooth operation of the door. INDECO A00 SERIES ALUMINIUM SYSTEM folding doors Installation Instructions Cut the top track > see page Install the top track Before fixing the top track, insert the top pivot socket, the roller and the positioner into the track. Fix the top track with screws, offsetting its face by: x = 9 mm profiles Advice: Avoid applying excessive force when tightening screws to prevent track deformation. Use cheese-head screws for best result. The surface to which the track is fixed must not be curved. Note: Before inserting the rollers, clean the inside of the suspended top track of any dirt that might accumulate during its installation. Install the bottom pivot socket Determine a plane running vertically along the centre of the top track (e.g. using a plumb line). Position the bottom pivot socket at a distance of y mm from the side wall of the recess (the dimension allows for mm buffer strip thickness). y = 9 mm y = mm profile profile Advice: When fixing the hinge, set the screws at the centres of the oblong holes, which will enable you to adjust the position in both directions. 9 Y

86 INDECO A00 SERIES ALUMINIUM SYSTEM folding doors Installation Instructions Set the door in place Fold the door and set it in place so that the bottom pivot pin / sits in the socket / (see the assembly drawing). Screw the top roller / bolt into the mounting block / using a 7 mm open-ended spanner. Using a mm open-ended spanner, unscrew the pivot pin of top pivot pin block / into the socket /. Move the locating screw block / to the stile and fasten the block. Determine the final door height and set it symmetrically in the opening. Use a level to plumb the door, repositioning the top pivot socket if necessary. Fasten the top pivot socket / and all lock-nuts. Advice: Exercise special care when installing doors. This operation should be performed by two persons. Adjust the door By turning the top and bottom pivot pins (right-left), adjust the door vertically so that it is about mm away from the wall when closed (this space will be filled by the dust-stop brush strip). Fasten the top and bottom pivot sockets to keep them in place. Close the door and adjust the top roller axle so that the door weight is distributed evenly between the hinge and the roller. By turning the pivot pins, door-to-floor clearance can be adjusted between 7 and 7 mm. Fix the locator Close the door when adjusted. Align the locator /9 with the locating screw. Mark the position of the locator and open the door. Fix the locator to the floor with screws. Note: The locator ensures stable position of the door when closed Fix the caps > see page Fix buffer strips > see page 77 Fix the buffer strip clip > see page0 Fix the positioner > see page 9 Fix the suspended top track fascia > see page 70 Fix the suspended top track fascia > see page 70

87 INDECO A00 SERIES ALUMINIUM SYSTEM folding doors System Components xx > see page 7 Wide Aluminium Rail ZL 0xx > see page 7 Aluminium Stile. 0xx > see page 7 Aluminium Stile xx > see page 7 Aluminium Stile. xx > patrz str. Aluminium Stile. xx > see page Aluminium Connector Rail. xx > see page Aluminium Connector Rail. xx > see page mm Aluminium Connector Rail. 0xx > see page mm Decorative Strip > see page 7 Aluminium Suspended Top Track A > see page > see page 7. x Allen-head Self-tapping Screw. Suspended Top Track End Cap. 00xx > see page Aluminium Decorative Profile > see page Transparent Plug for Aluminium Profiles. 0000xx > see page 9 Gasket. 9 0 A00 Hardware Set A hardware set for A00 aluminium folding door systems. Twin-bearing rollers. Accessories: mm spanner 90009, /0 mm spanner Packaging: set Weight: ~0. kg/set Availability: continuous 0xx> see page 7 Aluminium Suspended Top Track Fascia > see page Self-adhesive Cap. 0000xx > see page 0 Self-adhesive Safety Backing > see page Double-sided Self-adhesive Tape, 0. mm. 900xx 0000xx > see page 9 Self-adhesive Buffer Strip > see page Buffer Strip Clip. Self-aligning hinge for A00 aluminium system Colours: xx: SR-Silver, SA-Satin Packaging: pce Weight: ~0.07 kg/pce Availability: continuous 0999A > see page Buffer Strip Clip. 0AS > see page 7 Suspended Top Track Holder Fascia > see page 7 Suspended Top Track Holder.

88 INDECO ACCESSORIES AND TOOLS

89 INDECO ACCESSORIES AND TOOLS 00000x Large Angle Bracket Colours: x: 0 White, Black, Brown, Mahogany, Beige, Cherry, 7- Light Grey, Oak Packaging: 0 pcs/pack Weight: ~. kg/pack 0000x Small Angle Bracket Colours: x: 0 White, Black, Brown, Mahogany, Beige, Cherry, 7- Light Grey, Oak Packaging: 0 pcs/pack. Weight:.9 kg/pack 0000 Self-tapping Screw,. x A basic fixing element for the aluminium system. A. x fillister-head screw Packaging: 00 pcs/pack Weight: ~0. kg/pack 0000A. x Allen-head Self-tapping Screw. A basic fastener for the aluminium system. Packaging: 000 pcs/pack Weight: ~.0 kg/pack Availability: continuous Accessories: mm Allen key Screw,. x A self-tapping countersunk screw for roller fixing (S00). Weight: ~.0 kg/pack Packaging: 00 pcs/pack Availability: continuous Screw,. x A self-tapping countersunk screw for fixing a plastic rod socket to board (S00 and A00). Packaging: 00 pcs/pack Weight: ~0.9 kg/pack Availability: continuous Screw,.9 x A self-tapping screw for fixing a lock cylinder to body (S00, H00, A00, A00 and A00 systems). Packaging: 000 pcs/pack Weight: ~. kg/pack Screw,. x Packaging: 00 pcs/pack Weight: ~0.07 kg/pack All-purpose Screw, x Packaging: 00 pcs/pack Weight: ~0.0 kg/pack Screw,. x 9. A self-tapping fillister-head screw roller fixing (S00, S00 and S00). Packaging: 00 pcs/pack Weight: ~0.7 kg/pack Screw,. x A self-tapping fillister- head screw for fixing angular connectors. Packaging: 00 pcs/pack Weight: ~0. kg/pack Availability: continuous Screw,.9 x A self-tapping screw for lock and hinge fixing. Packaging: 00 pcs/pack Weight: ~. kg/pack Availability: continuous 7

90 INDECO ACCESSORIES AND TOOLS Screw,.9 x. A self-tapping screw for lock fixing. Packaging: 00 pcs/pack. Weight: ~0.9 kg/pack Automatic Notching Tool for steel rails and stiles. Packaging: pce. Weight: ~.0 kg/pce. M x 0 Screw for narrow-frame systems. Packaging: 00 pcs/pack. Weight: ~0.7 kg/pack. Availability: / Notching Tool for steel stiles and rails Accessories: blades 09xx Packaging: pce. Weight: ~0.00 kg/pce. 09xx Replacement blades for notching tool / Versions: xx: 00 narrow blade for rails, 0 wide blade for stiles. Packaging: pce. Weight: ~0.0 kg/pce. The set comprises x - narrow blade, x wide blade Hand-held Drill Jig for aluminium profiles Accessory: replacement sleeve Packaging: pce. Weight: ~.0 kg/pce Sleeve for Drill Jig for aluminium profiles Packaging: pce. Weight: ~0.0 kg/pce Bench Drill Jig for aluminium profiles, all-purpose. Packaging: pce. Weight: ~. kg/pce xx Pneumatic Cutting/Punching Press for steel rails and stiles. A Halifax B - Montreal C - rails Packaging: pce. Weight: ~.0 kg/pce. Availability: by order Pneumatic Press for steel top and bottom tracks. Packaging: pce. Weight: ~9.0 kg/pce. Availability: by order mm Allen key. Packaging: pce. Weight: ~0.0 kg/pce.

91 INDECO ACCESSORIES AND TOOLS Manual Press for Rails. Accessories: replacement blades 090 Packaging: pce. Weight: ~0.9 kg/pce. 000xx Veribor Vacuum Cup for glass. xx: 0 cups, cups. Packaging: pce. Weight: ~0.90 kg/pce. Availability: by order Manual Press for Stiles. Accessories: replacement blades 090 Packaging: pce. Weight: ~0. kg/pce Subland Drill, /9.7 mm. For the aluminium drill jig Packaging: pce. Weight: ~0. kg/pack /0 mm Adjusting Spanner. Packaging: 0 pcs/pack. Weight: ~0.0 kg/pack mm Adjusting Spanner. Packaging: 0 pcs/pack. Weight: ~0. kg/pack /0 mm Adjusting Spanner. Packaging: 0 pcs/pack. Weight: ~0.7 kg/pack Aluminium Connector Rail Bending Tool. A device for bending connector rails used for curved joints. Packaging: pce. Weight: ~. kg/pce. 000xx Wax Stick. Material for the correction of scratches on laminated boards. Colour xx: 00-White, 0-Black, 0-Brown, 0-Light Brown, 0-Cherry Tree, 0-Oak Packaging: pce. Weight: ~0.0 kg/pce. Availability: continuous; other colours available by order. 000 TOYO Oil Cutter. Accessory: replacement head 000, oil 000xx. Packaging: pce. Weight: ~0.07 kg/pce. Availability: by order. 000xx Oil for Oil Cutter For oil cutter 000. xx: 7A 00 ml Packaging: pce. Weight: ~0. kg/pce. 99

92 INDECO Aluminium profiles Material INDECO aluminium profiles are extruded from refined aluminium. This ensures excellent physical properties of profiles better rigidity and strength. Printed simulated wood decorative film Decorative film adhesive layer Satin anodized layer Anodized layer Conversion layer Aluminium Conversion layer Anodized layer Properties Properties that ensure corrosion resistance and colour fastness over the useful life of the product. - Corrosion protection anodized layer. - Resistance to UV radiation. 90 Surface finish The profiles have a coloured anodized surface. The anodizing process hardens the profile surface, which makes INDECO aluminium profiles highly resistant to mechanical damage. Four surface finish techniques are offered:. Anodizing. Formation of an oxide protective layer by galvanizing. A double satin finish provides attractive appearance.. Brushed anodizing. Surface brushing followed by anodizing, which produces a special decorative effect by adding a third dimension to the surface.. Laminating. Simulated wood finish is obtained by applying high-impact decorative film hot-applied with the use of thermosetting polymer adhesive.. Painting. A special technique of stoving paint powder coating produces the highest quality simulated wood finish. Colours, colour abbreviations The following colours / finish types are available on standing offer: Anodized, double satin: AS Silver AC Champagne AO Olive AG Gold Brushed anode: ASB Silver ACB Champagne Simulated wood paint: AWP White ASP Polished Silver ASM Metallic Silver AGP Polished Graphite Any other colour/pattern is available to order. Compliance: The anodized coat is anodized to Grade in accordance with EN 7-:00 and has a minimum average thickness of μm.

93 Aluminium Profile Colour Range AS Natural Anodized AG Gold AC Champagne AO Olive ASB Brushed Anodized ACB Brushed Champagne Note: The profile lengths stated in the catalogue represent usable lengths. In fact, the profiles are 0 cm longer for manufacturing reasons. 9 AWP White ASP Polished Silver ASM Silver metallic GRP Polished Graphite XX any colour/pattern available to order

94 INDECO Steel Profiles Material INDECO steel profiles are made from 0. mm quality higher-strength structural steel subjected to additional multiple surface treatment. As a result of a full treatment cycle, an advanced multi-layer product is obtained, with excellent physical properties. Polyethylene film backing Polyethylene backing adhesive layer Decorative polyester paint with polymer grain Paint undercoat Conversion layer Zinc coat Steel sheet Zinc coat Conversion layer Paint undercoat Polymer-grain decorative polyester paint 9 Properties Properties that ensure corrosion resistance and colour fastness over the useful life of the product. - Active corrosion protection two-sided zinc coating that provides sacrificial cathode protection of cuts and scratches. - Passive corrosion protection an additional two-sided coat of polyester paint. - Resistance to UV radiation. Surface finish Steel profiles are coated with gloss paint. Simulated wood finish is obtained by applying high-impact decorative film hot-applied with the use of thermosetting polymer adhesive. Both the paint and the film provide high mechanical resistance (HB H according to ISO 70). INDECO offers safe paints and films the pigments used are fast and completely safe for people. The surface layer contains polymer grains, which increase friction resistance, preventing surface scratching during use. Colours, colour abbreviations The following colours are available on standing offer: Painted profiles: SSR SSA SGL SGP SWP SBP SVP SCM Silver Satin Light Gold Pearl Gold White Black Vanilla Chrome Laminated profiles SBT SET SOT SLT SCT SPT SWT SMT SNT Beech Maple Oak Alder Cherry Tree Pear Tree Walnut Mahogany Wenge Any other colour/pattern is available to order.

95 Steel Profile Colour Range SSR Silver SSA Satin SGL Light Gold SWP White SBP Black SVP Vanilla SGP Pearl Gold SLT Alder SCT Cherry Tree SPT Pear Tree SWT Walnut SMT Mahogany SNT Wenge SCM Chrom 9 SBT Beech SET Maple XX Any other colour /pattern is available to order. SOT Oak

96 Sales Support Tools INDECO estudio is a tool that enables our retail customers to quickly, easily and intuitively design wardrobes, available at 9 WebPartner supports the process of Authorized Representatives establishing their presence on the Internet. The comprehensive package includes a website, server, domain, e.g accounts and ongoing website maintenance.

97 Sales Support Tools INDECO is the only company in the industry that has an internal business partner identification system, with the whole network covered by the Crib system at Access to the panel is possible only for Authorized Representatives, each of them having a unique access code. With such identification, it is possible to use the knowledge base, orders sent in by customers from the estudio application, modify pricing parameters, and to use the latest tools that make up the Online Ordering System and the INDECOSalsa program. The ordering system makes it possible to order online any quantity of products available on stock, including the generation of a sales invoice for online download. The whole process can be viewed on a panel between Indeco S.A. and an appropriate AR with Indeco sales staff chat and support options. 9 INDECOSalsa is a simple calculator of front panels. Having entered the dimensions of an opening and defined the system, connection and panel type, you will obtain the final dimensions of system components and cut-to-size panels forming the sliding door system.