ASSEMBLY INSTRUCTIONS CORONA 2 DOOR 1 DRAWER WARDROBE

Transcription

1 4m f You Tube SSMLY INSTRUCTIONS CORON OOR RWR WRRO IMPORTNT: R THS INSTRUCTIONS CRFULLY FOR SSMLING OR USING YOUR CORON OOR RWR WRRO. PLS KP THS INSTRUCTIONS FOR FUTUR RFRNC. HLTH & SFTY: O NOT use this item if any parts are missing, damaged or worn. O NOT use this item unless all fixings are secured. Please keep small parts out of reach of children. lways use on a level, even surface. It is recommended that two people handle and assemble the item. irlea advise you use the wall straps provided to further enhance the safety of this product. CR & MINTNNC: ssemble in the room of use. To avoid damages assemble the item on a soft, clean surface Periodically check all screws & fixings to ensure they are secure. O NOT push the item as this will damage the base. lways lift the item with two people to reposition. Keep any sharp objects away from the item. This product is manufactured in pine which is a wood with natural characteristics including knots, grains, clusters or indentations. On unpacking the item you may notice an odour due to production processes but this will disappear after a period of time. O NOT place the item next to a radiator or direct sunlight this item is susceptible to temperature change. It is recommended an even room temperature be maintained with no sudden fluctuations. O NOT place hot or cold items directly onto the surface of the item as marking will occur For general cleaning use a duster or damp cloth (almost dry) not wet do not use soap and water, detergents, aerosol sprays or any polish as use of these materials would invalidate any claims. O NOT place the item onto wet or damp flooring as staining may occur to the floor. 05mm 566mm 4 m 880mm Page of 4

2 Page of 4

3 PRTS LIST Part Item Qty HRWR LIST Part Item Qty Right Panel Wooden dowel 6 Left Panel ase/shelf Panel 4mm Screw 5 4 Top Panel C 5mm Screw 0 5 ack Panel 6 Large Spine 0mm Screw 59 7 Small Spine 5mm Screw 8 Rear ase Plinth 9 Right Front Frame F 50mm Screw 7 G H K L 9mm olt Handle Hinge Clip Plug M Hanging rail support N Stud O Corner bracket P Tack 40 Q Wall Strap R Washer 8 0 Left Front Frame Top Inner Plinth Support Plinth Front ase Plinth 4 Right oor 5 Left oor 6 oor ivider 7 rawer Front 8 rawer Side 9 rawer ack 0 rawer ase Top Side Plinth Top Outer Plinth ase Side Plinth 4 Front Plinth 5 rawer Runner 6 Cleat 7 Hanging Rail ** You will need a small mallet and a screwdriver. m Recycle 0 mm Page of 4

4 Step : Insert the right panel () into the right front frame (9) ensuring parts are fully pushed together and correctly lined up. Place the cleats (6) between the marks shown and secure using hardware part and a screwdriver (not provided). 9 6 No! Yes! Note: this side lined up. Step : Insert the left panel () into the left front frame (0) ensuring parts are fully pushed together and correctly lined up. Place the cleats (6) between the marks shown and secure using hardware part and a screwdriver (not provided). 0 6 No! Yes! Note: this side lined up. Page 4 of 4

5 Step : Insert hardware part using a small mallet (not provided). x 5 x 8 Step 4: ttach the drawer runner (5) to the right panel () and left panel () using hardware part F. Secure hardware part M using hardware part. You will need to use a screwdriver (not provided). M and F F 5 Page 5 of 4

6 Step 5: ttach the base/shelf panels (), rear base plinth (8), front base plinth () and support plinth () to the left panel () using hardware part and a screwdriver (not provided). 8 8 Step 6: ttach the right panel () using hardware part. Secure hardware part O using hardware part. You will need to use a screwdriver (not provided). O 8 8 Page 6 of 4

7 Step 7: ttach the top inner plinth () using hardware part C and a screwdriver (not provided). 0 C 9 C Step 8: ttach the top side plinths () using hardware part, and the top outer plinth () using hardware part F. You will need to use a screwdriver (not provided). a: 7mm b: F F Page 7 of 4

8 Step 9: ttach the top panel (4) using hardware part C and a screwdriver (not provided). Note: C Step 0: ttach the base side plinths () and front plinth (4) using hardware part and a screwdriver (not provided). 4 Page 8 of 4

9 Step : Insert hardware part N using a small mallet (not provided). N N N 46mm 46mm 5mm Step : Insert the hanging rail (7). 7 Page 9 of 4

10 Step : ttach hardware part to the right door (4) and left door (5) using hardware part. ttach the door divider (6) using hardware part. You will need to use a screwdriver (not provided) Step 4: Position the doors and secure using hardware part and a screwdriver (not provided). 4 5 Page 0 of 4

11 Step 5: ttach hardware part H using hardware part G and a screwdriver (not provided). H H H G Step 6: Secure hardware part K using hardware part. Insert hardware part L ensuring they are level and push the doors against it to create two small marks. Secure hardware part L in the two marks using hardware part. You will need to use a screwdriver (not provided). a: b: K 4 K L K L c: d: 4 K L L Page of 4

12 Step 7: ssemble the drawer components using hardware parts C, G and H with a screwdriver (not provided). a: 8 C b: C c: C d: G G H C H Step 8: Insert the assembled drawer and secure using hardware part and a small mallet (not provided). Page of 4

13 Step 9: oin the back panels (5) with the large spine (6) and small spine (7) and secure using hardware part P and a small mallet (not provided). P 7 P P P P P Page of 4

14 Step 0: Furniture must be fixed to a wall. Fix wall strap Q to top of furniture using washer R and screw. With help, move furniture into position. Wall plugs not supplied. The correct type of fixing must be used for your wall, seek professional advice if in doubt. R wall Q R dditional Information: For complete product information, images and dimension diagrams please visit the website If you have any issues with your item please contact the retailer directly you purchased it from who will be able to resolve any issues with irlea. Why don t you send us photos of your assembled furniture to info@birlea.com to be shared in our #birleahome feature on Instagram. Page 4 of 4