MIX & MATCH CAT40 ER Collet Chucks & Collets

Transcription

1 Canadians Supporting Canadians Pricing valid from January 1 to March 31, Winter Flyer MIX & MATCH CAT40 ER Collet Chucks & Collets Huge Savings on a 6-Pack CAT40 ER Collet Chucks 1. Select 6 Collet Chucks 2. Choose A Collet Set 3. Save $$ Threaded through holes for a back-up screw (tool stop) or coolant through when removed Factory balanced to save spindle life, tool life, and increase productivity DIN coolant option - standard All Ground Body 100% Forged Construction Wrench not included Promo Code 6PAK40 $ Sale Price: Possible savings of up to $ 1, (Promo not eligible for online ordering. Please be sure to include the promo code when sending or calling in your order.) Description CAT40 ER16 x 2.50 CAT40 ER16 x 3.50 CAT40 ER20 x 2.50 CAT40 ER20 x 4 CAT40 ER25 x 2.50 CAT40 ER25 x 4 CAT40 ER32 x 2.50 CAT40 ER32 x 3.13 CAT 40 Premium Balanced 30k RPM Code No List $ Code No List $ ER Collet Sets Description ER16 11pc 1/16-3/8 ER25 17pc 1/8-5/8 ER32 21pc 1/8-3/4 Distributed by:

2 5 MICRON AA ER COLLET SETS DIN 6343 Precision Collets have a runout of microns ( mm). GS High Precision Collets have a runout of microns ( mm). The new GS Extreme Precision AA Collets have a runout of only 5 microns (0.005mm). Features & Benefits: 12 slots instead of 16 allows sufficient collapse while increasing the area of contact with less tendency to distort. All edges are deburred and rounded to promote good interface with the taper of the chuck without the tendency to damage it. This results in more consistent repeatability. Collets are polished to eliminate blemishes that promote corrosion. Better corrosion resistance will result in longer product life of both the collet and the holder. Highly polished OD surfaces reduce the amount of force absorbed by friction between the collet and the collet chuck seat, increasing the grip force on the cutting tool. The inside bore of the collet is intentionally left unpolished to increase the friction between the collet and the cutting tool shank. Maximized Concentricity Evenly distributed cutting edges for high performance machining Minimized variation of cutting edges Consistent cutting profiles ensure the job stays within desired tolerances Improve system performance and lower cost per piece when used with quality GS chucks The result of an improved AA collet in a quality GS chuck is increased gripping force, improved rigidity, decreased runout, and a renewed confidence in your collet chuck system Micron AA ER Collet Sets Inch Metric For the full range of AA ER Collets visit Series No. Pcs. Range Code No. SALE $ ER11 Inch 7pc Set 1/16-1/4 x 1/ ER16 Inch 11pc Set 1/16-3/8 x 1/ ER20 Inch 15pc Set 1/16-1/2 x 1/ ER25 Inch 18pc Set 3/32-5/8 x 1/ ER32 Inch 21pc Set 1/8-3/4 x 1/ ER40 Inch 15pc Set 1/8-1 x 1/ Series No. Pcs. Range Code No. SALE $ ER11 Metric 13pc Set 1-7mm x 0.5mm ER16 Metric 10pc Set 1-10mm x 1.0mm ER20 Metric 12pc Set 2-13mm x 1.0mm ER25 Metric 15pc Set 2-16mm x 1.0mm ER32 Metric 18pc Set 3-20mm x 1.0mm ER40 Metric 23pc Set 4-26mm x 1.0mm

3 Gleason ground spiral bevel gears Internal coolant from positioning pin Internal air pressure Fixed Right Angle Heads WORK HOLDING IN STOCK Collet End Mill Tap Size Max Taper Model System Drill Cap Capacity R.P.M. Code No. Price $ CAT40 GFX07 ER11 7mm M6 10, , CAT40 GFX07L ER11 7mm M6 10, , CAT40 GFX10 ER16 10mm M8 10, , CAT40 GFX10L ER16 10mm M8 10, , CAT40 GFX16 ER25 16mm M12 8, , CAT40 GFX16L ER25 16mm M12 8, , CAT50 GFX10L ER16 10mm M8 10, , CAT50 GFX16 ER25 16mm M12 8, , CAT50 GFX20 ER32 20mm M16 4, , CAT50 GFX20L ER32 20mm M16 4, , SPECIAL Pivoting Angle Heads Collet End Mill Tap Size Max Taper Model System Drill Cap Capacity R.P.M Code No. Price $ CAT40 GPV16 ER25 16mm M12 4, , CAT50 GPV13 ER20 13mm M10 4, , CAT50 GPV20 ER32 20mm M16 4, , BT40 GPV16 ER25 16mm M12 4, , WE INVITE ALL INQUIRIES DOWNLOAD THE COMPLETE OFFERING AT 3-Jaw Cast Iron Scroll Chucks - 2pc Hard Rev. Jaws QUALITY IMPORT Ask for our complete range. Kitagawa Power Chuck Jaws Models B, BT, B200, BT200, HOH, HOB, N, NL 1.5mm x 60 Serrated C K These chucks are designed for all types of workshop machining operations on conventional lathes and milling fixtures. Smart design allowing inner parts to be replaced quickly B A D Chuck Hole Weight Dia. Dia. Mount (lbs) Code No. SALE $ Plain Back " Plain Back Soft Jaw Forming Ring The forming ring is used for cutting soft jaws by clamping and extending the thru hole to increase the accuracy of clamping the workpiece The size can be adjusted against the helical slot. Pin can be rotated 180º to extend the clamping range. Chuck Screw Set of 3 Dia. A B C D K Size Code No. SALE $ M " M " M Horizontal & Vertical Rotary/Dividing Table This HV Type Rotary Table is so designed as to permit machining operations at a higher dimension than that of RT Type rotary tables The base can be used in a vertical position to enable it to carry out centre work No need to drill new hole. The hole on the soft jaw can be used directly for pin Hardened and ground steel for durability Chuck Weight Model Dia. (kg) Code No. SALE $ VFR Table Base T-Slot Centre Model OD Dim. Width Sleeve Code No. SALE $ HV-6 150mm 200x160mm 11mm MT

4 IP67 Coolant Proof Digital Calipers Resolution: " / 0.01mm Hold function for easy reading Absolute and incremental measuring modes Inch/Metric conversion Metal Housing: the design will allow the caliper to be used in normal workshop conditions and is resistant to coolant, water, dust, and oil PRECISION TOOLS IP65 Digital Outside Micrometer w/ SPC Resolution Upon switch-on the display will read the actual Digital: "/ 0.001mm absolute measuring position Scale: " Automatic On/Off to maximize battery life Dual Ratchet combines both the Inch/Metric conversion Ratchet Stop and Friction Thimble Absolute or incremental measuring modes Protection level IP65 Carbide tipped measuring faces 0-6 /0-150mm ±0.001 /0.02mm /0-200mm ± /0.03mm /0-300mm ± /0.03mm Absolute Digital Calipers Resolution: " / 0.01mm Absolute and Incremental modes available Inch/Metric conversion A thumb wheel is provided for easy use 0-1 /0-25mm ± /0.002mm Outside Micrometers Flatness: " / 0.6μm Carbide tipped measuring faces Grey painted steel frame Graduation: Ratchet Stop 0-6 /0-150mm ±0.001 /0.02mm /0-200mm ± /0.03mm /0-300mm ± /0.03mm Digital Calipers Resolution " / 0.01mm The origin position is retained through the on/off cycle Inch/Metric conversion 0-6 /0-150mm ±0.001 /0.02mm /0-200mm ± /0.03mm /0-300mm ± /0.03mm Dial Calipers Graduation: Stainless steel construction with all measuring surfaces surface-hardened The dual pinion mechanism offers ultra smooth feel Preloaded pinion offers better repeatability Thumbwheel 0-6 ± ± ± ± ± SETS Range Code No. SALE $ Economical Digital Outside Micrometer Resolution "/ 0.001mm Carbide tipped measuring faces Spindle dia.: 0.25" Friction thimble Inch/Metric conversion Absolute or incremental measuring modes Automatic On/Off to maximize battery life Ball Anvil included 0-1 /0-25mm ± /0.004mm AGD2 Dial Indicator Dial face dia.: 2.20"/ 58mm Internal tolerance marker Flat back (attached) and lug back supplied With counter pointer Dial Reading: Range/Rev: 0.1 Accuracy: ±0.002 Range Graduation Code No. SALE $

5 ISO Certified 2 Year Warranty Centering Indicator Graduation " Provides a simplified method of centering a work piece or fixture on horizontal for vertical machines, internal or external diameters. Face of indicator remains stationary in any desired position while the machine spindle rotates, leaving the operator with both hands free to accurately position the machine table Shank Dia.: 3/8" Operating speed not to exceed 800rpm Range Internal: 5/32" - 12" External: Up to 12" Dial ± Dial Test Indicator Sets Graduation: " Jeweled bearings Comes with Ø3/8" dovetail stems Easy to read yellow face Carbide tipped contact point 1.26" dia. dial face Full Set Carbide tipped point DIA. Φ2mm Steel point DIA. Φ1mm Stem Dia. Metric 4mm Inch 0.157" Base Set Horizontal Dial Range Accuracy Reading Type Code No. SALE $ 0.03 ± Horizontal Full Set 0.03 ± Horizontal Swivel Clamp Metric for Ø4mm, & Ø8mm Dia. Inch for 3/8", & 0.157" Dia. Holding Bar Metric 9x9x100mm Inch 0.25"x0.5"x4" Stem Dia. Metric Φ8mm Inch Φ3/8" Knurled Clamping Ring wrench Dial Bore Gauge Moveable probe pin with carbide ball Graduation is anvils, 1 sub-anvil, 4 spacers Articulating Arm Magnetic Bases Dial gauges can be held by the 3/8 or 8mm diameter stem or by the lug backing plate Arm has 3 articulating joints that can be locked with the single hand knob The precision surfaces and the bottom V are securely fastened to the ferrous work piece or machine table when the rotary knob is in the On position Working angle 150º Power Base Height Code No. SALE $ 80kg 60x50x55mm 350mm kg 60x50x55mm 440mm Dial Probe Range Travel Depth Code No. SALE $ (AGD2) Magnetic Bases Accepts test indicators with dovetail clamping mechanism Dial gauges can be held by the 3/8 or 8mm diameter stem or by the lug backing plate The rotary knob switches natural magnet On or Off The precision surfaces and the bottom V are securely fastened to the ferrous work piece or machine table when the rotary knob is in the On position # with Fine Adjustment. Power Base Main Stem Code No. SALE $ 80kg 60x50x55mm Ø12mm kg 60x50x55mm Ø12mm

6 NOGA Noga Mag Base / STM Indicator Combos MG6161 ( ) MG HOLDER WITH DOUBLE FINE ADJUSTMENT New double fine adjustment Bottom: unique single direction Top: universal swivel clamp Holds 6mm, 8mm, 3/8, dovetail, and lug back Five axis holder Unique central locking mechanism with Noga designed spring loaded bearing Powerful magnetic base 80kg/f DIAL INDICATOR ( ) 1, 0-100, Reverse counter Stainless steel components Rotating bezel with clamp Lugback (1/4" hole) Interchangeable point Conforms to AGD 2 standards Teclock Style Promo N Set - NG8000 For Steel, Aluminum, Plastic Contains: NogaGrip-2 handle 10pcs N1 blades Code No.: $ DG1033 ( ) DG STANDARD HOLDER 11 reach Noga central locking mechanism with Noga designed spring loaded bearing Powerful On/Off magnetic base (80kgf) Dial gauge holder is three-dimensional DIAL INDICATOR ( ) 1/2, 0-100, Reverse counter Stainless steel components Rotating bezel with clamp Lugback (1/4" hole) Interchangeable point Conforms to AGD 2 standards N Cobalt Set - NG8100 For Plastic & Hard Materials Contains: NogaGrip-2 handle 20pcs N10 Cobalt blades Code No.: $ NG NG Promo S Set - NG8150 For Steel, Aluminum, Plastic Contains: NogaGrip-1 handle 10pcs S10 blades S Golden Set - NG8152 TiN For Abrasive Materials Contains: NogaGrip-1 handle 10pcs S10 TiN coated blades NG NG N Economy Set - NG8050 For Steel, Aluminum, Plastic Contains: NogaGrip-2 handle 20pcs N1 blades N Golden Set - NG8002 TiN For Steel, Aluminum, Plastic Contains: NogaGrip-2 handle 10pcs N1 TiN coated blades NG NG Ask for our new Noga Brochure or download it from SowaTool.com 6

7 Coating with good surface roughness and welding resistance Coating with oxidation resistance at high temperature and plastic deformation resistance Coating with excellent chipping resistance due to improved adhesion PT22C INSERTS STEEL TURNING CVD GRADE Good surface roughness and welding resistance. Oxidation resistance at high temperatures and plastic deformation resistance. Excellent chipping resistance due to improved adhesion. Fine coating layer with toughness and wear resistance. Exclusive substrate material to improve wear resistance. [ Current Grade ] [ New Grade (PT22C) ] FOR MORE INFORMATION ABOUT THE PT22C INSERT CALL TODAY TO GET A COPY OF OUR TECH BROCHURE OR DOWNLOAD IT AT For Steel Turning New CVD Grade (P20) PT22C JUST A SMALL SAMPLE OF A WIDE RANGE OF GEOMETRIES & CHIP BREAKERS CCMT32.52-F2P Code No.: Excellent chip control at shallow depth of cut and low feed rate. Suitable for stainless steel cutting. $7.74 SCMT32.52-F3P Excellent chip control at shallow depth of cut and low feed rate. Excellent surface finish due to reduced cutting force. Suitable for fine boring. Code No.: $7.32 CNMG432-M Code No.: $9.12 TCMT32.52-F3P Excellent chip control at shallow depth of cut and low feed rate. Excellent surface finish due to reduced cutting force. Suitable for fine boring. Code No.: $8.88 CNMM433-R3 Specially designed tough cutting edge provides superior cutting performance at deep depth of cut and fast feed rate. Smooth chip flow and reduced cutting force. DCMT32.51-F2P Excellent chip control at shallow depth of cut and low feed rate. Suitable for stainless steel cutting. DNMG432-M1 Code No.: $8.34 Code No.: $9.60 Code No.: $11.16 TNMG332-M TNMG431-M WNMG432-M Code No.: $7.98 Code No.: $11.28 Code No.: $9.12 KNUX R11 Code No.: Suitable for general cutting conditions. $

8 Multi-tasking Vises Tool Box Multi-tasking 5-Axis Modular Vises MADE IN ITALY ABS plastic Two levered trays Model Dimensions (mm) Code No. SALE $ VTB W x 235D x 180H Precision Lock-Well II Milling Vises This slightly modified version of the famous AUTO-WELL Lock-Well vise has features including the exclusive LOCK DOWN principle which guarantees that the movable jaw stays securely down during The MULTITASKING range of vises has been specially designed for 5-axis machines. Working on 5 sides of the workpiece, it allows the best optimization of the machining cycle. Thanks to the compact design this kind of vise can be installed on all machining centers. The use of GRIP jaws is strongly recommended with multitasking vises. Self-centering or eccentric Eccentric jaw adjustment in steps of 2mm Highest accuracy in positioning and alignment (±0.02mm) due to ground rack teeth on both the base and the fixed jaws Minimum deflection Solid, rigid construction and maximum clamping ratio to the total length Positioning through ground holes or keyways All case hardened to HRC60 for durability Type 3 Type 1 & 2 Model No. A B C a b c d e f Weight Code No. SALE $ AMC kg AMC kg Type 1 & 2 Vise shown with riser Type 3 Precision Milling Machine Vise Vises are matched (bed height: ) Interchangeable soft jaws Chip cover protects leadscrew from damage An integral key and large fasteners reduce deflection by 50% 10 year warranty 8 X 10 Opening: $1, Code # Type 1 Type 2 Type 3x166 Type 3x266 Code No SALE $ 2, , , , A A W B C ød/d E F G H øl H M kg kn Pricing valid from January1 to March 31, 2019 or while quantities last. We reserve the right to make changes without notice and accept no liabilities for mistakes and printing errors. All taxes extra. Printed in Canada *CADIS45*