Floor-Mounted Tubfiller

Transcription

1 Floor-Mounted Tubfiller Installation Guide TSP510 TSU

2 Attention Before Installation 1. Inspect this product to ensure you have all parts as shown that are required for proper installation. 2. The valve cartridge has been factory tested and adjusted DO NOT TAKE THE CARTRIDGE APART. Taking the cartridge apart will void the warranty. 3. Ensure that both hot and cold water feeds are properly connected to the marked lav connecting. 4. This product must be installed by a professional contractor. 5. Refer to the specification and assembly drawings attached for installation directions.. Flow Pressure Min. 25 PSI, Max. 0 PSI. Recommended pressure 50 to 0 PSI. Installation Requirements Please read the instructions carefully so as to avoid any damage to the fixture. 1. To ensure this product is installed properly, you must read and follow these guidelines. 2. The owner/user of the faucet must keep this information for future reference. 3. Be sure your installation conforms to local codes. 4. Refer to the specification and assembly drawings attached. Faucet is sold partially assembled but shown fully disassembled for illustrative and service purposes only. 5. Inspect this product to ensure you have all parts required for proper installation.. Use only a strap wrench or protected/smooth-jaw wrench on any finished surface.. If possible, install the faucet assembly on the sink or mounting surface before setting.. Do NOT use putty during this installation. Cleaners For Fittings And Accessories To avoid damaging the surface and working components of the fittings, certain precautions must be taken in terms of usage and subsequent cleaning as many cleaning agents contain acids for general cleaning and removing calcium deposits. When caring for your fittings and accessories, please note the following: Only apply cleaners which are expressly intended for the use Never use any cleaner containing hydrochloric acid, formic acid or acetic acid on or near the fitting, as they can cause considerable damage Do not use cleaners containing phosphoric acid Do not use cleaners containing chlorine bleach solutions Never mix or combine cleaning agents Abrasive cleaners and unsuitable scouring agents such as scouring pads Technical Support Assistance If further assistance is required, please contact: Product support at (09:00-1:00hrs PST) or technical@blubathworks.com North America Blu Bathworks Inc. 1 Smithe Street, Vancouver BC, Canada, VB A9 T F

3 Installation Instructions Recessed Concrete / Wood Floor Installation 1. Locate desired location of fixture prior to pouring concrete floor. Note: Rough-in for 510 is 4 1 /2 (114mm) Ø and 520 is 3 / x 9 1 /2 (12mm x 241mm) 2. Prior to pouring concrete floor, insert knock out in location minimum x (510) and x 14 (520) to provide flexibility and room for hot and cold water supply line hook up. Note: finish floor material will cover oversized opening. 3. Depth of rough in opening should be min /2 (51-4mm) to finished floor. Note: please allow for finish floor material thickness. 4. Place rough-in assembly over desired location and make marks for the placement of the mounting screws. 5. Drill a 1 /2 (12mm) pilot hole for each mounting screw.. Concrete floors Insert threaded mounting screw, with the provided anchor attached, into each of the three pilot holes so that the threading on each screw is facing upwards.. Wood floors The rough-in is to be secured by lag bolts (not provided), as per install diagram.. Place the rough-in assembly onto the screws in the floor and adjust the small brass screws around the valve until it is level. 9. Place a metal washer, followed by a locking washer onto the threaded part of each screw sticking above the rough-in. 10. Tighten the rough-in into place by tightening a locking nut onto each screw over the metal washers. 11. Attach the water supply to the rough-in assembly by connecting the hot water supply on the left and the cold water supply on the right. 12. Test the rough in connection for leaks prior to floor finish. 13. Tile the area surrounding the valve, leaving open a hole with a diameter of 5-90mm ( ). 14. Remove the protective plate from the top of the rough-in valve, exposing the water outlets. 15. Insert the main fixture body into the rough-in so that the supply lines plug into the water outlets. 1. Securely tighten the large brass nut at the base of the fixture body. Insert the extension tightening rod provided into the hole in the fastening nut and thread onto the rough in turning in a clock wise direction until secure. 1. Slide the escutcheon down so that it rests against the floor and completely covers the brass nut. 1. Connect one end of the shower hose to the hose attachment underneath the shower hook, and the other end to the base of the hand-held shower head. 19. Push the spout into place on top of the mixer body and tighten the set screw using the provided Allen wrench. 20. Attach the horizontal control rod to the appropriate height on the connector. 21. Once everything is installed then test the fixture and make sure there are no leaks. Technical Support Assistance If further assistance is required, please contact: Product Support at (09:00 1:00hrs PST) or technical@blubathworks.com North America Blu Bathworks Inc. 1 Smithe St, Vancouver, BC, Canada, VB A9 314 East 1st Ave,Vancouver, BC, Canada, V5M 1C3 T F T F

4 510 Series Recess installation in concrete or wood floor construction 1 Rough-in Ø 4 1/2" Leveling screws Two outlets Hot inlet Ø 4 1/2" Cold inlet Edge of bath tub 2 3-Ø12 Drill 3x1/2" (12mm) holes for anchor bolts for concrete install When installing the rough-in valve into or on top of the floor, ensure both the location and orientation properly relate to the bathtub. 1 3 Hot Depth of rough-in from finished floor. 2"-2 1/2" (50-0) Test the tap for water pressure, and check for leaks prior to proceeding to next steps. 2 5 Cold 4 Securely fasten rough-in into or on top of floor surface Connect hot and cold water lines into rough-in inlets Check rough-in to ensure it is level 1. If mounting the rough-in onto finished floor surface the rough-in will be visually exposed. A second escutcheon cover plate is required. 2. If mounting the fixture on wood floor construction additional solid blocking is required to secure and mount the rough-in. Refer to diagram. Test the level Non recess installation for wood frame construction Finished floor 5" lag bolt (not supplied) Freestanding tub filler rough-in mounted to sub floor (do not recommend mounting on finished floor) ¾" Sub floor Plywood Wood joist 0 Adjust all leveling screws Wood to ensure joistrough-in is securely fastened and level prior to floor finishing and mounting fixture body. 5" lag bolt (not supplied) Solid blocking secured between floor joists Solid block to min 4 *Note: Additional escutcheon cover required: TS10 for TSP510, TSA510, TSU510 / TS20 for TSP520, TSA Insert the main body into the floor rough-in, tighten the nut using the tightening extension bar by inserting it into the holes in the side of the fastening nut. When the body is secured place the escutcheon. Cover plate over the floor opening. Install the spout, shower hose and shower, and test. 4

5 When installing the rough-in valve into or 2. on If mounting top of the the floor, fixture ensure on both wood the floor location construction additional to next solid steps. blocking and orientation is required properly to secure relate and to mount the bathtub. the rough-in. Refer to diagram. 1. If mounting the rough-in onto finished floor surface the rough-in will be 2visually exposed. A second escutcheon cover plate is required. 2. If mounting the fixture Test the on level wood floor construction additional solid blocking is required to secure and mount the rough-in. Provide a hole Refer to diagram. in the finished floor of 2 1/2" - 3 1/" (ø5~ø0) Test the level Provide a hole in the finished floor of 2 1/2" - 3 1/" (ø5~ø0) Insert the main body into the floor rough-in, tighten the nut using the 9 tightening extension bar by inserting it into the holes in the side of the fastening nut. Insert When the the main body body is secured into place the the floor escutcheon rough-in,. Cover tighten plate the nut over using the floor the opening. tightening extension bar by inserting it into the holes in the side of the fastening nut. When the body is secured place the escutcheon. Cover plate over the floor opening. Adjust all leveling screws to ensure rough-in is securely fastened and level prior to floor finishing and mounting fixture body. Adjust all leveling screws to ensure rough-in is securely fastened and level prior to floor finishing and mounting fixture body Install the spout, shower hose and shower, and test. Install the spout, shower hose and shower, and test. 5

6 TSP510

7 TSU510

8 TSP

9 TSU510 Trim Exploded Diagram TSU510 9

10 warranty LIMITED FURNITURE RESIDENTIAL WARRANTY Blu Bathworks ( Blu ) furniture products are warranted to the original purchaser to be free from defects in all material and workmanship during normal residential use for a period of five (5) years from the date of purchase. Blu will, at its election, repair, provide a replacement part or product, or make appropriate adjustment, subject to the terms and conditions set forth in this warranty. LIMITED CERAMICS RESIDENTIAL WARRANTY Blu Bathworks ("Blu") ceramic products are warranted to the original purchaser to be free from defects in all material and workmanship during normal residential use for a period of one (1) year from the date of purchase. Blu will, at its election, repair, provide a replacement part or product, or make appropriate adjustment, subject to the terms and conditions set forth in this warranty. LIMITED blu stone RESIDENTIAL WARRANTY Blu Bathworks ("Blu") blu stone products are warranted to the original purchaser to be free from defects in all material and workmanship during normal residential use for a period of five (5) years from the date of purchase. Blu will, at its election, repair, provide a replacement part or product, or make appropriate adjustment, subject to the terms and conditions set forth in this warranty. Blu Bathworks does not recommend exceeding US/Canada maximum hot water temperature regulations of 150 F/5 C, respectively. Exceeding stated temperatures could result in damage to blu.stone basins and bathtubs. LIMITED ACRYLIC BATHTUBS RESIDENTIAL WARRANTY Blu Bathworks ("Blu") acrylic bathtubs are warranted to the original purchaser to be free from defects in all material and workmanship during normal residential use for a period of five (5) years from the date of purchase. Blu will, at its election, repair, provide a replacement part or product, or make appropriate adjustment, subject to the terms and conditions set forth in this warranty. LIMITED TAPWARE RESIDENTIAL WARRANTY Blu Bathworks ( Blu ) tapware products are warranted to the original purchaser to be free from defects in all mechanical parts and polished chrome finishes during normal residential use for as long as the original purchaser owns his or her home. Blu will, at its election, repair, provide a replacement part or product, or make appropriate adjustment, subject to the terms and conditions set forth in this warranty. LIMITED ELECTRONICA TAPWARE RESIDENTIAL WARRANTY Blu Bathworks ( Blu ) electronica tapware products are warranted to the original purchaser to be free from defects in all electronic parts during normal residential use for a period of five (5) years from the date of purchase. Blu will, at its election, repair, provide a replacement part or product, or make appropriate adjustment, subject to the terms and conditions set forth in this warranty. LIMITED COMMERCIAL WARRANTY Blu Bathworks ("Blu") products are warranted to the original purchaser to be free from defects in all material and workmanship during normal usage for a period of one (1) year from the date of purchase. Blu will, at its election, repair, provide a replacement part or product, or make appropriate adjustment, subject to the terms and conditions set forth in this warranty. terms and conditions This warranty applies only to Blu Bathworks ("Blu") products distributed in North America. This warranty is non-transferable and is for the exclusive benefit of the original purchaser of a Blu product. This warranty may be exercised by the original purchaser of a unit in a new residential development. Blu recommends using a professional plumber for all installation and repair. This warranty does not apply to products that have been installed in any manner other than as set out in Blu s printed instructions, or to products that have been altered in any way. For further clarity, the above stated warranty does not cover or apply to damage attributable to: (a) neglect, misuse, abuse, accident or negligence; (b) normal wear and tear; (c) dirt or lime scale, or the use of inappropriate cleaners (such as those containing abrasives, ammonia, acids, waxes, bleaches, solvents, alcohol, or any product not recommended for chrome); and (d) damage caused by transportation, or improper storage. This is the only warranty of Blu, which makes no other warranty of any kind. Blu disclaims any liability for special, incidental or consequential damages. In no event shall the liability of Blu under this warranty exceed the purchase price of the product. PROCEDURE FOR WARRANTY SERVICE Refer to blubathworks.com for policy and procedures relating to requests for service under the terms of this warranty. Original proof of purchase is required. Blu is not responsible for removal or installation costs, or the costs of shipping and handling associated with any service. Repaired or replaced products or parts are warranted only for the period remaining under the initial warranty. 10