Transcend Overbed Table - Assembly, Maintenance and Parts Manual
|
|
- Julia Williams
- 5 years ago
- Views:
Transcription
1 Transcend Overbed Table - Assembly, Maintenance and Parts Manual Your table may vary from this illustration 45 Goodrich Drive, Kitchener, Ontario, Canada N2C 0B8 tel fax
2 Thank you for your recent purchase of our Over Bed Table. Although this product is engineered to provide years of reliable performance, a little common sense maintenance and operational checks will help to keep it in top condition. Should any questions arise regarding the performance and maintenance of the table please call our toll-free line (877) for assistance. Unpacking The package contains the following: 1) Table Top 2) Column 3) Base 4) Casters 5) Fasteners Fasteners 1 - M8 nut 2 - lock washers 4-5/16-18 x 3/4 cap screws 6 - wood screws The M8 nut and two washers are installed loosely on the end of the gas spring. Casters Fig. K 35mm 50mm Caution! The column is shipped with the gas spring retracted. Care must be exercised in cutting the strap as the cylinder will extended suddenly under pressure. - Page 2 -
3 Assembling the Over Bed Table A) Attaching the Casters to the Base 1) The smaller caster 35m diameter wheel goes on the low end of the base, farthest from the column and the larger, 50mm caster goes on the column end of the base. 2) Using a hammer and punch (or a strong hand) force the caster onto the grip ring stem until a snap is heard and the axle housing rotates freely. Force should be directed to the axle housing directly over the hole into which the grip ring is inserted (See Fig K). Fig. K B) Attaching the Column to the Base Two persons make this process easier. 1) Place the base on the floor and tilt it toward you so that the underside is facing you. 2) Place the column on the floor so that it is resting on the front edge of the table support plate. Put one of the two lock washers on the threaded stud at the end of the gas spring (Fig A) and then have an assistant slide the gas spring through the hole in the base cover (Fig B) and secure the threaded end of the gas spring with the nut and second lock washer to the underside of the base. This nut must be tightened securely (Fig C). 3) Using the four 5/16-18 x 1-1/4 cap screws, securely fasten the column to the base as illustrated in Figure C. Gas Spring Nut and Lock Washer Fig. A Fig. B Fig. C - Page 3 -
4 C) Attaching the Top to the Column 1) Secure the Over Bed table top to the support bracket using the 6 wood screws. Holes for the screws have been predrilled. Warning! Do NOT use power tools to attach the top column. Overtightening may result in the top breaking free under force, from the column. The Over Bed table is now ready for use. Care and Cleaning of your Over Bed Table The Stance Transcend Overbed Table is made up of three components: Top, Column and Base. All of the components will withstand cleaning using a solution of 0.5 Hydrogen Peroxide (such as Virox ) or a 70% Isopropyl alcohol solution following the recommended cleaning frequency of a patient room environment as set out in such guidelines as Best Practices for Environmental Cleaning by PIDAC. Top The Transcend table top is available in two configurations; a molded polyurethane with a high pressure laminate insert or, alternatively, a PVC thermoformed top over a MDF substrate. The molded polyurethane edges should not be cleaned using bleach or harsh cleaners with abrasive additives. Iodine and Betadine have the greatest staining potential. The PVC thermoform top should not be cleaned using harsh cleaners with abrasive additives. In addition, cleaning products such as bleach or those containing solvents such as lacquer thinner must be avoided. Column The column is made of an anodized aluminum should not be cleaned using harsh cleaners with abrasive additives. Base The base cover is made of ABS plastic and should not be cleaned with any solvent based cleaner such as lacquer thinner. All cleaning products containing citrus oil must be avoided. Casters Casters should be regularly inspected and cleaned of debris that will impede their ability to roll and swivel. Frequency of Cleaning Cleaning frequency of the Transcend Overbed Table should follow the recommended cleaning procedures by such organizations as PIDAC. Typically in the case of patient room equipment, cleaning of the table top should be done after each use and daily of the entire table. - Page 4 -
5 Maintenance of your Over Bed Table A) Scheduled Service and Inspections Depending on frequency of use, the Over Bed table should receive scheduled service and inspections. 1) Casters should be cleared of debris to ensure that they swivel and roll smoothly. No lubrication is required. 2) The entire table should be check for structural integrity and damaged components. Looseness between the top and the column and the column and the base should be noted and corrected immediately. B) Adjusting the Column 1) Remove the Over Bed Table top. CAUTION: Once the weight of the top is removed the column will extend to its full height. 2) Remove the two screws (Fig D) which secure the upper column to the table support bracket and drop the column. 3) Of the four rollers in the carriage assembly, two adjust to increase or decrease the pressure of the rollers on the outer column this will be the upper roller on one side of the carriage and the lower roller on the opposite side. In order to adjust the rollers, begin by loosening the two jam nuts shown in Fig E. If there is excess play between the rollers and the column begin by adjusting one cap screw at a time clockwise in small ¼ turn increments with a Allen wrench (also shown in Fig E). Once you begin to feel a small amount of drag on the column when moving the column up and down, tighten the jam nut and repeat the same process with the other cap screw. If there is excess drag or tension between the rollers and the column back off both cap screws counterclockwise with an Allen wrench (as shown in Fig E) one or two full rotations. If the drag remains it may be necessary to run the column up and down by hand to force the rollers away from the column. If the drag still pesists you may need to slide the column off the rollers and then force the two U shaped adjuster brackets which house the rollers upward until they seat against the bottom of the cap screws. Once you can feel excess play between the rollers and the column next adjust one cap screw at a time clockwise in small ¼ turn increments until you can again feel a small amount of drag on the column. Tighten the jam nut and repeat the same process with the other cap screw. - Page 5 -
6 Jam Nut Fig. D Fig. E Fig. F 4) The rollers should not be lubricated. 5) Resecure the column and the top to the table support bracket and reinstall the top. 6) Wobble end to end of 1/4" and side to side of 1/4" is acceptable. See Figure F. C) Replacing the Gas Spring 1)Turn the table on its side and remove the M8 nut and lock washers which secures the gas spring to the underside of the base (Fig C). 2) Remove the two screws securing the upper column and lower the column toward the base (Fig D). 3) Now loosen the jam nut and unscrew the rod from the Table Support Plate (Fig H). 4) Remove the old gas spring and install the new one. 5) Assemble the table in the reverse order. CAUTION: When threading the rod of the new gas spring into the Table Support Plate, extreme care should be taken not to damage the rod. The jam nut must also be threaded all the way down to the end of the rod before installing the rod. Fig. H D) Parts and Service If parts and service are required for your Over Bed table, please contact your dealer or Stance Healthcare Inc. direct at (877) , or by to service@stancehealthcare.com. - Page 6 -
7 Parts Diagrams - ST180 with V Base - Page 7 -
8 Parts Diagrams (Con t) - Page 8 -
9 Parts Diagrams (Con t) - Page 9 -
10 Parts Diagrams (Con t) - Page 10 -
11 Specifications: Size of Top: 18 x 32 Weight capacity of table top: 75 lbs centered on the table top (25lbs safe working capacity) Overall Height with column extended: 45 Overall Height with column lowered: 30 Total Travel: 15 Base Dimensions: (H Base) 19-5/8 x 29-1/2 (V Base) 21-1/8 x 32-1/4 Minimum Base Height: 1-7/8 Warranty: Stance Healthcare Inc. is pleased to warrant products it manufactures against defects in materials and workmanship for a period of two (2) years to the original purchaser beginning from the date the product was shipped to said purchaser. This warranty shall not apply to products that have been subjected to misuse, abuse, negligence, accidental damage, damage in transportation or improper maintenance. In addition, this warranty shall not apply to any product whose original construction has been altered by someone other than Stance Healthcare Inc. Stance Healthcare Inc. hereby disclaims all implied warranties including the implied warranty of merchantability or fitness for any particular purpose. At its discretion, Stance Healthcare Inc. will repair or replace defective parts that meet the terms and conditions of this warranty at no charge to the original purchaser: Return freight charges incurred under warranty claims will be paid by Stance Healthcare Inc. provided that the customer received written authorization and shipping instructions from Stance Healthcare Inc. to proceed with the return. Stance Healthcare Inc. 45 Goodrich Drive, Kitchener, Ontario, Canada N2C 0B8 t: f: w: stancehealthcare.com Stance Healthcare OMST180 Owners Manual, ST180 Transcend OBT, REV 10, Date: 03/16 - Page 11 -
Owner s Manual ODYSSEY BENCH MODEL. O4100B shown REV E. Southern Avenue, Phoenix, AZ USA Workhorseproducts.
Owner s Manual ODYSSEY BENCH MODEL O4100B shown 67-1375 REV 218 3730 E. Southern Avenue, Phoenix, AZ 85040 USA 800-778-8779 Workhorseproducts.com 1 Table of Contents I. Introduction & Safety Information.
More informationOwner s Manual CD-42 CULTIVATING DISC MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE Made In CHINA REV
MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945 Owner s Manual CD-4 CULTIVATING DISC IMPORTANT Read and follow all Safety Precautions and Instructions Before Operating this Equipment. Made In CHINA
More informationModels 2230 and 2240
Models 2230 and 2240 Overview... 2 Tools Needed... 2 Hardware...3 Assembly... 4-13 Installation... 14 Drawer Removal... 15 Operation... 15 Maintenance... 15 Accessories... 16 Limited Warranty... 16 Perform
More informationOwner s Manual AE PLUG AERATOR MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE Made In CHINA REV
MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945 Owner s Manual AE-48 48 PLUG AERATOR IMPORTANT Read and follow all Safety Precautions and Instructions Before Operating this Equipment. Made In CHINA
More informationShop Style Miter Saw Stand Kit
Quality Power Tool Accessories OWNER S MANUAL Assembled Unit Shown Without Shelves & Wings Assembled With Shelves & Wings Shop Style Miter Saw Stand Kit Model 2850 IMPORTANT Read and understand all safety
More informationETCHING PRESS MANUAL
ETCHING PRESS MANUAL FOR ALL SPEEDBALL ETCHING PRESSES Updated October 2018 TABLE OF CONTENTS Delivery Notes 3 Unpacking 4 Floor Stands 6 Safety Tips 6 Maintenance 7 Diagram 8 Warranty Card 9 2 This manual
More informationRITE-HITE RAINGUARD TM
RITE-HITE RAINGUARD TM RG-3000 Trailer Top Seal Installation Instructions & Owner s Manual Date of Installation: This Manual Covers All Units Shipped 8/04 to Date PRINTED IN U.S.A. PUBLICATION NO. RG30-0010
More informationSTRINGING MACHINE OWNER'S MANUAL. Copyright 1998 GAMMA Sports - All Rights Reserved
6002 STRINGING MACHINE OWNER'S MANUAL Issue 3 - June 20, 1998 Copyright 1998 GAMMA Sports - All Rights Reserved 6002 OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... FEATURES PAGE 3... ASSEMBLY
More informationModels 2130 and 2140
Models 2130 and 2140 Overview... 2 Tools Needed... 2 Hardware... 2 Assembly... 3-10 Installation...11 Operation... 11 Maintenance... 12 Accessories...12 Limited Warranty... 12 Printed in USA 2007 Perform
More informationOWNER'S MANUAL Issue 2 - December 14, 2000
OWNER'S MANUAL AL Issue 2 - December 14, 2000 Copyright 2000 GAMMA Sports - All Rights Reserved Provided by www.gssalliance.com OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2...FEATURES PAGE
More informationModels 2130 and 2140
Models 2130 and 2140 Overview... 2 Tools Needed... 2 Hardware... 2 Assembly... 3-10 Installation...11 Operation... 11 Maintenance... 12 Accessories...12 Limited Warranty... 12 Perform the following sequence
More informationModels 2030 and 2040
Models 2030 and 2040 Overview... 2 Tools Needed... 2 Hardware... 2 Assembly... 3-8 Installation... 9 Operation... 9 Maintenance... 10 Accessories... 10 Limited Warranty... 10 Document # 101290 0607 Printed
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationNOVA-EXT Versatile Projector Mount Model: NOVA-EXT
INSTALLATION MANUAL NOVA-EXT Versatile Projector Mount Model: NOVA-EXT NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 800-368-9700 Fax: 800-832-4888 Other Locations
More informationMODEL 83 Pail Handler
MORSE MFG. CO., INC. 727 West Manlius Street P.O. Box 518 East Syracuse, NY 13057-0518 Phone: 315-437-8475 Fax: 315-437-1029 Email: service@morsemfgco.com Website: www.morsemfgco.com COPYRIGHT 2005 MORSE
More informationINSTRUCTION MANUAL. Lathe Duplicator MODEL North Glenn Road, Casper, Wyoming woodworker.com
140-069LatheDuplictr(1/12) 10/30/06 8:20 AM Page 1 INSTRUCTION MANUAL Lathe Duplicator MODEL 140-069 1108 North Glenn Road, Casper, Wyoming 82601 1-800-645-9292 woodworker.com 140-069LatheDuplictr(1/12)
More informationInstallation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays
Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays Models: PLA60, PLA60-S, PLAV60, PLAV60-S Max UL Load Capacity: 175 lb (79 kg) 2300 White Oak Circle Aurora, Il 60502
More informationPage 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16
R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LACPACC-002 LACPACC-003 LACP-16TxxLP5 (0.5-in lead screw pitch) LACP-16TxxL1 (1-in lead screw pitch) C P I R K 4 ea Flanged
More informationTilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM
Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM Easy installation Built-in level for easy positioning Corrective leveling adjustments after installation Forward /
More informationUser Instruction Manual Model# RK21 RK21-M
User Instruction Manual Model# RK21 RK21-M FOR SALES, SERVICE OR TECH SUPPORT CALL: 1800-BUY-RIVET or 1-800-289-7483 WWW.RIVET.COM CONTENTS Safety Page 3 Specifications Page 3 Jaw Maintenance and Replacement
More informationManual Carton Closing Staplers
Operator s Manual Manual Carton Closing Staplers SHB00-A Item No. 6400 -/8" Crown Carton Closing Stapler 5/8" and /4" (5mm and 8mm) Ask for Genuine INTERCHANGE A58 and A4 Staples SHB50-C Item No. 640 -/4"
More informationOPERATORS MANUAL WEEKENDER STEEL LADDER RACK
OPERATORS MANUAL WEEKENDER STEEL LADDER RACK WWW.WEATHERGUARD.COM MODELS 1450 & 1475 1475 Shown INSTALLATION TIME Approximate installation time: 60 minutes (depending on truck equipment installation experience
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Swingout Arm for 37 to 47 Flat Panels Model: AM80 NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1-800-368-9700 Fax: 1-800-832-4888
More informationPrime Engineering Up-Rite Stander
OWNER S MANUAL PRODUCT PHOTO PARTS LIST ASSEMBLY INSTRUCTIONS MAINTENANCE WARRANTY Prime Engineering Up-Rite Stander Manufactured By Prime Engineering A Division of Axiom Industries Industries, Inc. 4202
More informationCOMPETITOR CB-610 STANDARD BENCH
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice COMPETITOR CB-610 STANDARD BENCH Hardware Identifier Assembly Instruction Exploded Diagram Parts List
More informationSecurity Products & Services...That Never Sleep. Sur-Lock. I/O 2000L Family of Exit Control Alarm Locks. Installation Instructions
Security Products & Services...That Never Sleep Sur-Lock I/O 2000L Family of Exit Control Alarm Locks Installation Instructions IMPORTANT It is important that you read and follow these instructions carefully.
More informationInstruction Sheet D-CPU. Secure CPU Holder
Instruction Sheet D-CPU Secure CPU Holder I-00457 Rev A PARTS LIST NOTE: Select Security Components when a more secure application is desired. Mounting Track with Mounting Tape Security Bracket Assembly
More informationOWNER S MANUAL. Distributed by ASLI, 1011 Centre Road, Wilmington, DE Tools Required: Allen Wrench
Tools Required: Adjustable Wrench Allen Wrench OWNER S MANUAL Retain This Manual For Reference Distributed by ASLI, 1011 Centre Road, Wilmington, DE 19805 TABLE OF CONTENTS BEFORE YOU BEGIN..... 1 IMPORTANT
More informationOWNER S MANUAL STORAGE SHED MODELS: STOR-96-G-W-1RH & STOR-912-G-W-1RH
STORAGE SHED MODELS: STOR-96-G-W-1RH & STOR-912-G-W-1RH OWNER S MANUAL Introduction.. 1 Assembly Instructions STOR-96-G-W-1RH... 2 Assembly Instructions STOR-912-G-W-1RH... 8 STOR-96-G-W-1RH Exploded Parts
More informationContinuum Frame Assembly Instructions
Continuum Frame Assembly Instructions Copyright January 1, 2017 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.2 Table of Contents Continuum Frame Table of Contents... i Warranty...ii
More informationTilting Flat Panel Wall Mount Installation Guide
Tilting Flat Panel Wall Mount Installation Guide Model: A580TM Easy installation Built-in level for easy positioning Safety bolts lock the TV on the mount Easy to adjust tilt angles: +5 to -15 degrees
More informationAssembly Instructions and Owner s Manual Flex TechBridge
Assembly Instructions and Owner s Manual Flex TechBridge Contents Important User Information...........................2 Safety Precautions.................................2 Required Tools.....................................3
More informationHollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide
Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Tools Required: two adjustable wrenches, pliers, ¾ socket wrench recommended Note: please do assembly near your vehicle as you Can
More informationMODEL T28000 HEAVY-DUTY MOBILE BASE INSTRUCTIONS
MODEL T28000 HEAVY-DUTY MOBILE BASE INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Introduction Your new Model T28000 Heavy-Duty
More informationDual Arm Tilt LCD Mount
Installation Manual model # 51324 M o u n t i n g S y s t e m s Dual Arm Tilt LCD Mount Fits Displays 13 to 32 Supports Up to 50 lbs (23 kgs) Projection from Wall from 3 to 17 Meets VESA Standards 50/75/100,
More informationPlease Do Not Return This Product To The Store!
MODEL NO. T8176 QUICK SERVE 3000 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts may
More informationInstallation Instructions TrekStep Side Mount
Installation Instructions TrekStep Side Mount Vehicle Application Ford F150 Regular Cab and Super Cab 2009 Current Part Number: 75402-15 Fits both Driver s and Passenger Side www.bestop.com - We re here
More information- INSTALLATION INSTRUCTIONS -
. Supercharger Shaft Upgrade Kit PART# - RY17040-UK-6S5-2 APPLICATION(S): Yamaha FX-SHO, FZR & FZS Required tools Part# IN LB Electronic Torque Wrench N/A T-30 Torx Bit Socket N/A 3mm Allen Wrench N/A
More informationOPERATION MANUAL MODEL
OPERATION MANUAL MODEL 60-511504 SUPPLIER CODE: GO-60-511504 BREEZER MESH OFFICE TASK CHAIR - GRAY/BLACK CUSTOMER SERVICE For fastest service, please visit our website at www.comfortproducts.net/support
More information!ATTENTION: READ BEFORE ASSEMBLING/OPERATING! ASSEMBLY INSTRUCTIONS FOR THE MULTICHAIR 6000Tilt Series
!ATTENTION: READ BEFORE ASSEMBLING/OPERATING! ASSEMBLY INSTRUCTIONS FOR THE MULTICHAIR 6000Tilt Series multichair 6000Tilt multichair 6200Tilt multichair 6000Tilt P1 multichair 6000Tilt P2!ATTENTION: READ
More informationM ACS Instructions
APPLICABLE MODELS: Nissan Frontier 2005 and up short bed with Utili-Trak mounting rails PACKAGE CONTENTS 00-0060-M-01-1205 ACS Instructions Leitner Designs 25675 Taladro Circle Unit E Mission Viejo, CA
More informationINSTALLATION INSTRUCTIONS
CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS PDS-PLUS Universal Projector Mount Model: NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700
More informationTHANK YOU FOR PURCHASING OUR STUDIO RTA CREATION STATION
THANK YOU FOR PURCHASING OUR STUDIO RTA MODEL# 20672 IF YOU REQUIRE ANY ASSISTANCE WITH ASSEMBLY, PARTS, OR INFORMATION ON OTHER PRODUCTS, PLEASE VISIT OUR WEBSITE: www.studiorta.com OR CALL OR WRITE THE
More informationThank you for choosing a Yost Vise. For future reference please record the following:
Thank you for choosing a Yost Vise. For future reference please record the following: Model #: Purchase Date: Supplier: LV-4 I n s p e c t i o n a n d A c c e p t a n c e Claims for damage, shortage or
More informationQ-Zone Hoop-Frame. Assembly Instructions. Copyright July 11, 2018 Grace Company (Reproduction Prohibited) Version 1.8
Q-Zone Hoop-Frame Assembly Instructions Copyright July 11, 2018 Grace Company (Reproduction Prohibited) Version 1.8 Table of Contents Table of Contents... i Warranty... ii Parts List Box 1...iii Box 2...
More informationSpecifications. Important Safety Information
Specifications Tire Rim Capacity 4 to 12 Rim Height 16 (2) Bead Breaker Handles 21 Long Includes Aluminum Centering Cone (2) Nylon Spacers Important Safety Information 1. Do not exceed max. tire capacity.
More informationPlease Do Not Return This Product To The Store!
MODEL NOS. T8512 TOURNAMENT SERIES 3 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts
More informationINSTALLATION INSTRUCTIONS
CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount for 42 to 63 Flat Panels NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone:
More informationOPERATION MANUAL MODEL T SUPPLIER CODE: BJ T
OPERATION MANUAL MODEL 60-5800T SUPPLIER CODE: BJ-60-5800T COMMODORE II BIG & TALL LEATHER EXECUTIVE CHAIR CUSTOMER SERVICE For fastest service, please visit our website at www.comfortproducts.net/support
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Short Throw Projector Arm Model: UNI-STA/UNI-EXT NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1-800-368-9700 Fax: 1-800-832-4888
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS AM2 / AM2-B Articulating Swingout Arm NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations Phone:
More informationTilting, Swiveling & Rotating Flat Panel Wall Mount
Tilting, Swiveling & Rotating Flat Panel Wall Mount Model: VXA980TC +5 to -5 +5 to -5 Supports most 0-80 Flat Panel TVs Maximum Weight Capacity: 32 lbs. Supports VESA Sizes up to 600x500 For technical
More informationOwner s Manual LSP38 38 Lawn Sweeper
Owner s Manual LSP38 38 Lawn Sweeper Manual Contents Safety Instructions Assembly Operation Maintenance Parts Warranty 2 4-13 2 11 14-15 16 Your Lawn Sweeper Congratulations on your purchase of a new Precision
More informationF-150 Structural Holding System
F-150 Structural Holding System Users Manual December 2013 by Vehicle Service Group. All rights reserved. CO8812.2 502073 Rev. - 12/11/2013 CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive
More informationInstallation Instructions Hinged Roof Rack
Installation Instructions Hinged Roof Rack Application: Jeep Wrangler Unlimited 2004 - Current Part Number: 41435-01 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question
More informationInstallation Instructions TrekStep Side Mount
Installation Instructions TrekStep Side Mount Vehicle Application Chevrolet Silverado / GMC Sierra All Bed Sizes 1999 Current Part Number: 75400-15 www.bestop.com - We re here to help! Visit our web site
More informationSunset Swings By Health in Motion, LLC
Sunset Swings By Health in Motion, LLC Model 421 Lounge Swing Assembly and Operation Manual Record Serial Number Here www.sunsetswings.com by Health In Motion, LLC. 11/6/2009 421 Owners Assembly and Operation
More informationInstall Instructions. NewAge Steel Welded Tall Locker
Kit Contains Full Width Adjustable Steel Shelves (4) Height-Adjustable Steel Leveling Legs (4) Aluminum Door Trim (2) 2.5 x ¼ Cabinet Mounting Lag Bolts (4) Large Zinc Plated Mounting Washers (4) 5/8 x
More informationMast R Lift II. User Manual for Incra Mast-R-Lift II. Suggested Router Bit Speeds. Model #02120
Mast R Lift II User Manual for Incra Mast-R-Lift II Model #02120 61 Forest Plain Road Oro-Medonte, Ontario, Canada L3V 0R4 Toll Free: 1-866-272-7492 Email: jessem@jessem.com Website: www.jessem.com Thank
More informationOwner s Manual & Safety Instructions
Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s
More informationPlease read and understand the OnBoard Timpani Cart Owner s Manual before using the Timpani Cart.
Assembly and Owner s Manual OnBoard Timpani Cart Performance Position Towing Position CONTENTS Important User Information...........................2 General......................................2 Manufacturer.................................2
More informationAutoSPLITTER STRAIGHT HEAD MODELS
AutoSPLITTER STRAIGHT HEAD MODELS HYDRAULIC NUT SPLITTER OPERATIONS AND MAINTENANCE MANUAL 1 CONTENTS INTRODUCTION... Page 3 WARNINGS AND SAFETY TIPS... Page 4 POWER REQUIREMENTS... Page 5 ASSEMBLY...
More informationAssembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set
Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708482 Ph.: 800-274-6848 Revision C2 02/2013
More informationMidmark Care Exchange 6282 Standard Duty Wall Mounted Workstation
INSTALLATION MANUAL Midmark Care Exchange 6282 Standard Duty Wall Mounted Workstation Weight Capacity 5-20 lbs 1210180MD Rev. C TABLE OF CONTENTS Tools Required / Installation Warnings / Disclaimer / Safety
More information20 TON HyDRAULIC SHOP PRESS with GRID GUARD 06/2015 INSTRUCTION MANUAL MODEL: KHP-20T-GG COPYRIGHT 2015 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
06/2015 20 TON HyDRAULIC SHOP PRESS with GRID GUARD MODEL: KHP-20T-GG INSTRUCTION MANUAL COPYRIGHT 2015 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC. warranty INFORMATION 2-yEAR LIMITED WARRANTY FOR THIS
More informationKURT D810 AngLock Vise Base Assembly
KURT MANUFACUTRING - LIFETIME IRONCLAD TM WARRANTY All Kurt Manufacturing Company industrial workholding products and parts with the exceptions noted below, are warranted against defects in material and
More informationPlease Do Not Return This Product To The Store!
MODEL NOS. T81 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may be shipped inside
More informationSawStop. Contractor Fence Assembly OWNER S MANUAL. Model CNS-SFA
Contractor Fence Assembly OWNER S MANUAL Model CNS-SFA Warranty warrants to the original retail purchaser of the Contractor Fence Assembly accompanying this manual that the fence assembly will be free
More informationRead and understand all of the instructions and safety information in this manual before operating or servicing this tool.
Operating Instructions BENDstation RIGID Workstation (RB-000) Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. FAILURE TO OBSERVE
More informationFletcher-Terry Titan Series Rotary Trimmers
Fletcher-Terry Titan Series Rotary Trimmers Instruction Manual Provided By http://www.mybinding.com http://www.mybindingblog.com OWNER S MANUAL Fletcher Titan The Fletcher-Terry Company 65 Spring Lane
More informationTABLE OF CONTENTS DESCRIPTION. Safety Instructions Assembly Operation... 7
TABLE OF CONTENTS DESCRIPTION PAGE Warranty... 1 Safety Instructions... 2 Assembly... 3 Operation... 7 #360 Grain Cleaner Drawings... 8 #360 Grain Cleaner Parts List... 10 Utility Auger Option Drawing...
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationJenny Legs Assembly Instructions
Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:
More informationMast R Lift II. User Manual Model # for INCRA METRIC Mast-R-Lift II
Mast R Lift II User Manual Model #02123 for INCRA METRIC Mast-R-Lift II 61 Forest Plain Road, Oro-Medonte, Ontario, L3V 0R4 Canada 866-272-7492 Toll Free 705-726-8233 Local Phone 705-327-0295 Fax Email:
More informationHARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet
HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet Read the enclosed instructions and recommendations before any installations CONTENTS Dead-Length Collet Adaptation
More informationAST-2446 INSTALLATION INSTRUCTIONS
AST-2446 Suspension Adapter AST-2446 INSTALLATION INSTRUCTIONS Single Stud Installation Step 1. Secure the ceiling plate to the ceiling structure (see WARNING). Step 2. Use suitable hardware (commercially
More informationAssembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set #
Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set #1002493 JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708482 Ph.: 800-274-6848 Revision C3 02/2014 www.jettools.com
More informationth St N Oak Park Heights, MN Phone: Fax:
12430 55 th St N Oak Park Heights, MN 55082 Phone: 651.342.1756 Fax: 651.342.1293 Email: info@diacro.com SAFETY INFORMATION PG. 3 MAINTENANCE PG. 3 #4 BENDER BREAKDOWN AND PARTS LIST PG. 4-6 QUIK-LOK BREAKDOWN
More informationP4263TP. Installation Guide. Low-Profile Tilting Portrait Mount for Flat-Panels
Low-Profile Tilting Portrait Mount for Flat-Panels 1321 S. State College Blvd., Fullerton, CA 92831 USA Weight Limit Maximum Flat Panel Weight: 175 lbs. Warning Statements THE WALL STRUCTURE MUST BE CAPABLE
More informationINSTRUCTION MANUAL TAPER ATTACHMENT MODEL M1022. Phone: (360) On-Line Technical Support: FOR USE WITH MODEL M1019
MODEL M1022 TAPER ATTACHMENT FOR USE WITH MODEL M1019 INSTRUCTION MANUAL Phone: (360) 734-3482 On-Line Technical Support: tech-support@shopfox.biz #6809BL COPYRIGHT DECEMBER, 2004 BY WOODSTOCK INTERNATIONAL,
More informationSawStop. T-GlideTM. Fence System- Professional Series II OWNER S MANUAL
SawStop T-GlideTM Fence System- Professional Series II OWNER S MANUAL Warranty SawStop warrants to the original retail purchaser of a new T-Glide Fence System - Professional Series II from an authorized
More information!ATTENTION: READ BEFORE ASSEMBLING/OPERATING! ASSEMBLY & PACKING INSTRUCTIONS FOR THE MULTICHAIR 6000 Series
!ATTENTION: READ BEFORE ASSEMBLING/OPERATING! ASSEMBLY & PACKING INSTRUCTIONS FOR THE MULTICHAIR 6000 Series multichair 6000 multichair 6200!ATTENTION: READ BEFORE ASSEMBLING/OPERATING! November 2016 ASSEMBLY
More informationINCRA. Suggested Router Bit Speeds. pg Website:
INCRA Mast R Lift II R User Manual For Rockler Tables Model #02121 61 Forest Plain Road, Oro-Medonte, Ontario, Canada L3V 0R4 Toll Free: 1-866-272-7492 Email: jessem@jessem.com Website: www.jessem.com
More informationOperating Instructions and Parts Manual Folding Hydraulic Crane Model: JFHC-200X
This Manual is Bookmarked Operating Instructions and Parts Manual Folding Hydraulic Crane Model: JFHC-200X WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-106206K Ph.: 800-274-6848 Revision
More informationUSER MANUAL. Cart, Mast & Boom. Assembly & Installation
Cart, Mast & Boom Assembly & Installation USER MANUAL 5845 WEST 82ND STREET INDIANAPOLIS, INDIANA 46278 U.S.A. Phone (317) 875-5592 Fax (317) 875-5456 Email gcisales@glascraft.com Web www.glascraft.com
More informationQuick Release Hardware
Backs and Support OWNER MANUAL Quick Release Hardware TFB Hardware Quick Release Owner s Manual Customer Satisfaction 1.0 Stealth Products strives for 100% customer satisfaction. Your complete satisfaction
More informationOWNER'S MANUAL. Please Do Not Return This Product To The Store!
MODEL NO. T8190SA TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may be shipped inside
More informationPORTABLE ADJUSTABLE BASKETBALL SYSTEM
Instruction Manual PORTABLE ADJUSTABLE BASKETBALL SYSTEM P A R T S L I S T 5 1/2 and 8 safe play clearance Item Qty Description Item Qty Description A 1 Portable Base Assembly M 4 1/2 Lock Nut B 2 Front
More informationOperating Instructions and Parts Manual SLT-1100 Jumbo Scissor Lift Table
Operating Instructions and Parts Manual SLT-1100 Jumbo Scissor Lift Table JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-140780 Ph.: 800-274-6848 Revision B1 05/2014 www.jettools.com Copyright
More informationHARDINGE Installation booklet For:
HARDINGE Installation booklet For: L Flange Nose Dead-Length Collet Adaptation Chucks Draw Collet Read the enclosed instructions and recommendations before any installations WARRANTY & RETURN PROCEDURES
More informationParts List. U-DS92ST Ashley Creative Center With Padded Stool Assembly Instructions. [15] - Plastic Thick Washer (2 - pieces) [22] - Wrench (1 piece)
[1] - 23.5 x 35.5 Top [8] - Drawer Support Rods Parts List [15] - Plastic Thick Washer (2 - pieces) [22] - Wrench [2] - Upper Base left End (1 pieces) [9] - Media Supports (1 pieces) [16] - loor Guides
More informationIMPORTANT WARNINGS AND CAUTIONS!
I N S T R U C T I O N M A N U A L The Christie Vivid Green ceiling mount will suspend your Christie Vivid Green projector in an upright position to compliment conference rooms, classrooms or home theater
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS P4263F Universal Low Profi le Flat Mount for 42 to 63 Flat Panels NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888
More informationPortable Platform Scale
Installation Manual Portable Platform Scale BPP1000 Series BPP2000 Series 1990-2015 by Fairbanks Scales, Inc. All rights reserved 50699 Revision 5 08/2015 Disclaimer Every effort has been made to provide
More informationMANCHESTER VANITY BASE
MANCHESTER VANITY BASE INSTALLATION INSTRUCTIONS Questions? Call our customer service department at 1-855-995-5578, 8:30 a.m. - 5 p.m., EST, Monday - Friday or e-mail: contactus@magickwoods.com. Models:
More informationTow-Behind Spreader. 175 lb Capacity MODEL NUMBER SP-175TB Rev
Tow-Behind Spreader 175 lb Capacity IMPORTANT Read and follow all Safety Precautions and Instructions Before Operating this Equipment. MODEL NUMBER SP-175TB Made In CHINA 15912 Rev.08-273 LIMITED WARRANTY
More informationThank you for choosing a Yost Vise. For future reference please record the following:
Thank you for choosing a Yost Vise. For future reference please record the following: Model #: Purchase Date: Supplier: 34C I n s p e c t i o n a n d A c c e p t a n c e Claims for damage, shortage or
More informationPORTROD WALL MOUNTED HEIGHT ROD
PORTROD WALL MOUNTED HEIGHT ROD USER INSTRUCTIONS P/N UMPORTROD Rev 1-052112 1 PORTROD Thank you for your purchase of this Health o meter Professional product. Please read this manual carefully, and keep
More informationMenu Board Tilt or Fixed Mount Installation Instructions MDS1T-200, MDS1T-300, MDS1T-400 MDS2T-200, MDS2T-300, MDS2T-400 MDS3T-200, MDS3T-300, MDS3T-400 MDS4T-200, MDS4T-300, MDS4T-400 MDS5T-200, MDS5T-300,
More informationTABLE OF CONTENTS DESCRIPTION. Safety Instructions Assembly Operation... 7
TABLE OF CONTENTS DESCRIPTION PAGE Warranty... 1 Safety Instructions... 2 Assembly... 3 Operation... 7 #360 Grain Cleaner Drawings... 8 #360 Grain Cleaner Parts List... 10 Utility Auger Option Drawing...
More information