A total solution of precise AC/DC TIG welding and plasma cutting machine

Transcription

1 TC-05AC/DC -IN- Multi-process:arc welding and plasma cutting Features: Process: AC TIG, DC TIG, MIX TIG, MMA, Plasma Cutting Soft-switching IGBT inverter system Full digitalized control system, friendly operation interface Precise arc start control as lower as to Amps Fast Sport Arc system Multiple AC waveform adjusting MIX TIG control system T/T control mode Pilot arc start for 50A plasma cutting is optional. 0 channels memory capacity Application: Metal fabrication workshops Shipyards and offshore industry Chemical and process industry Mechanized welding Car body repairs and maintenance A total solution of precise AC/DC TIG welding and plasma cutting machine TC-05AC/DC built base on the MASTERTIG system offers precise, expert AC/DC TIG welding process. It s a precise aluminum welding specialist that suits all welded materials. Modular design allows you to build the package that best suits your needs. TC-05AC/DC also comes with a heavy duty cycle plasma cutting power source. What you need for any metal welding or cutting works, you just get this combo machine and it s all you needs. Easy operation and full functions: from the control panel allowing fast adjustment of all necessary controls for DC, AC and MIX TIG welding with either HF or contact ignition. It s also very convenient to store or call out the welding parameters from the memory channels. Tel: ( 86) Fax:(86) robin@broad.hk BROAD INDUSTRIAL GROUP

2 TC-50AC/DC -IN- Multi-process:arc welding and plasma cutting Technical specifications Item No Rated Input Voltage Max. Load Power Capacity Rated Duty Cycle (0oC) 60% Welding Current/Voltage Range Open Circuit Voltage 00% Power Factor Efficiency TIG Pulse Peak Current Base Current Pulse Frequency Pulse Width (Ratio) AC AC Frequency Range TIG AC Clean Width (AC Balance) AC Clean Ratio (AC Bias) % MIX MIX TIG MIX Frequency: TIG DC Balance: (%) Arc-starting Current Crater-filling Current Current Up-slope Time Current Down-slop Time Pre-Gas Time Flow-Gas Time Spot Arc Time MMA Arc Force Hot Start Time Hot Start Current PAC Required Air Pressure Gas Pro-flow/Retard Time Max.Cutting Thickness Dimension (LxWxH) Weight (KG) Standard accessories: TIG torch: WP-6 Plasma torch: P60 Electrode holder with cable M Earth clamp with cable M Optional accessories: Pilot arc system Argon gas regulator: W-69B Gas pressure regulator Water-cooling Unit: WC-00 Trolley: WT-00 TC-05AC/DC PH ~ 0V +5% TIG:.5KVA MMA: 5.6KVA PAC: 6.KVA TIG: 00A/8V MMA: 60A/6.V PAC: 50A/00V TIG: 60A/6.V MMA: 0A/5.V PAC: 0A/96V TIG: 5A/0.V~00A/8V MMA: 0A/0.V~60A/6.V PAC: 0A/88A~50A/00V MMA:70V~80V ; PAC:60V~90V % 5A~00A 5A~00A 0.Hz~50Hz ~00% 0Hz~00Hz +0~-0 +0~-50 0.Hz~5Hz 0~90 0A~60A 5A~00A 0.S~0S 0.S~5S 0.S~5S 0.S~5S 0.S~0S 0A~00A 0A~60A S 0.~0.5MPa S~0S 8 57x0x5mm 5KG Tel: ( 86) Fax:(86) robin@broad.hk BROAD INDUSTRIAL GROUP

3 TC-50AC/DC -IN- Multi-process:arc welding and plasma cutting Panel & connections Control Panel. Output connectors Power Switch. Gas input connector. Input power cable: ~ phase 0-0V, 50/60Hz. Earth (Grouding). Tel: ( 86) Fax:(86) robin@broad.hk BROAD INDUSTRIAL GROUP

4 TC-50AC/DC -IN- Multi-process:arc welding and plasma cutting General View of Control Panel DC +/- converter output arcstarting of AC TIG process Process Selection Spot Welding Mode AC Frequency Control + AC Balance Control + Independent AC Amperage Control == samilar to MILLER system. AC Wave Type MIX TIG mode for every pulse cycle. Memory with capacity of 0 sets parameters. Pulse control PILOT ARC DC+/DC-: the arc-starting output polarity converter at AC TIG & MIX TIG process AC waveform: AC welding with rectangular current output wave form. Maximum power loading and safe welding. AC welding with sinusoidal current output wave form. Low noise levels. Memory channels add usability It s includes 0 memory channels to s- tore welding values for later use. This makes it quick and easy to start welding without needing to adjust the settings once more. Tel: ( 86) Fax:(86) robin@broad.hk BROAD INDUSTRIAL GROUP

5 TC-50AC/DC -IN- Multi-process arc welding and plasma cutting AC Wave Controls 5 Tel:(86) Fax:(86) robin@broad.hk BROAD INDUSTRIAL GROUP

6 TC-50AC/DC -IN- Multi-process:arc welding and plasma cutting MIX TIG Control Features of MIX TIG: The AC current can get a very good clearance, and DC current can get a deeper penetration. Use the MIX TIG we can get an excellent Arc Concentration, can be carried out the excellent welding performance from thin to thick plate. ) Nice weld appearance, deep penetration. ) Excellet Arc Concentration. ) Substantially reduce the electrode consumption. MIX TIG AC TIG MIX TIG Frequency (Hz): the cycle time of MIX TIG in second. Adjustable range: 0.-0Hz. MIX TIG Balance (DC) %: DC Balance (%) = (tad/tmix) x 00 6 Tel: ( 86) Fax:(86) robin@broad.hk BROAD INDUSTRIAL GROUP