F78MP Series Radar FEATURES AND BENEFITS

Transcription

1 F78MP Series Radar The F78MP Series air radar sensor provides non-contact, continuous level measurement for bulk materials in bins, tanks and silos. Accurate and reliable in difficult environments, the F78MP Series is an ideal level meter for powder and bulk solid inventory management. The F78MP Series air radar withstands corrosive environments and takes consistent measurements in steam, dust and other turbulent conditions. HOW IT WORKS The F78MP Series air radar measures the level of material in a bin or silo by monitoring the time it takes for an emitted microwave pulse to travel from the level meter to the surface of the material being measured and back to the meter. This time is calculated into distance which is then translated into a level measurement. NEW MODELS! Bindicator radar now transmits at a 78 GHz frequency with a 4 degree beam angle. The higher frequency and narrow beam angle combine to create the most versatile radar unit on the market. SIMPLE INSTALLATION with a quick set-up procedure and various mounting options No moving parts and standard air purge for MINIMAL MAINTENANCE FEATURES AND BENEFITS Quick Start Wizard for easy configuration 78 GHz transmitting frequency with a narrow beam angle of 4 Standard, directional or aiming flange options to direct unit to optimal location 2-Wire 20 to 32 VDC Power Supply Measures up to 131 or 328 feet (40 or 100 m) Standard air purge connection ENDLESS APPLICATIONS working in some of the most challenging environments like plastics and powders HOW TO ORDER 2 2 A A 2 Mounting G = 3 Aiming (Directional) Aluminum Flange (Note 2) H = 4 Aiming Aluminum Flange (Note 3) J = 6 Aiming Aluminum Flange (Note 3) K = 3 Stainless Steel Flange (Note 1) L = 4 Stainless Steel Flange (Note 1) M = 6 Stainless Steel Flange (Note 1) Approvals 2 = Hazardous Location MP Series F78MP040 = 131 ft (40 m) Radar F78MP100 = 328 ft (100 m) Radar NOTES: 1. Standard flanges are not pressure rated; atmospheric pressure only in. Directional flange is a split flange and has 5 degree rotation; 3 bar pressure rating and 6 in. Aiming flange has 10 degree rotation; 3 bar pressure rating.

2 F78MP Series Radar SPECIFICATIONS FUNCTIONAL Power Supply Nominal 24 VDC with max 550 Ohm loop resistance; Maximum 30 VDC Dead Zone 15.7 in. (400 mm) from refererence point Measurable Distance 131 ft (40 m) or 328 ft (100 m) Transmitting frequency 78 to 79 GHz FMCW Update Time Maximum 10 seconds (depends on Settings) Beam angle 4 degrees PERFORMANCE Accuracy 0.2 in. (5mm) including hysteresis and non-repeatability Ambient Temperature -40 to 175 F (-40 to 80 C) Ambient Pressure 12 to 15 psi ( 860 to 1060 mbar) Process Temperature -40 to 392 F (-40 to 200 C) Output signal 4 to 20 ma, HART HART Communication Load 230 to 550 Ohm; 230 to 500 Ohm when connecting a coupling module Maximum Line Length 4,921 ft (1500 m) multi-wire Humidity 45 to 75% relative humidity Dielectric Constant Minimum dk of 1.6 for ranges up to 65.6 ft (20 m) Minimum dk of 2.5 for ranges up to 328 ft (100 m) PHYSICAL Material Powder coated 316 Stainless Steel Protection Type 4X/NEMA 4X; Type 6/NEMA6, IP68 Conduit Entry 1/2 NPT Mass 6.94 lb (3.15 kg) (with 3 SS flange) Mounting 3, 4 or 6 in. flat flange or 3 in. Directional flange with 5 rotation or 4 or 6 in. Aiming flange with 10 rotation APPROVALS & RATINGS FM and CSA (US and Canada) Hazardous: Dust Ignition Proof: Class II, Div1, Groups E, F, G; Class III T4 Hazardous: Non-incendive: Class I, Div 2, Groups A, B, C, D, T4 CE Electromagnetic Compatibility Directive Low Voltage Directive DIMENSIONS Universal Flange 4.33 [110.00] 3 : 7.87 [200.00] 4 : 6": [229.00] [285.00] 6 : [285.00] 3 in. Directional Flange 4.33 [110.00] 7.87 [200.00] 4 and 6 in. Aiming Flange Dimensions available at 6.93 [176.00] 0] [9.60] 6.54 [166.10].92 [23.3] sensor reference point 150 Venture Boulevard Spartanburg, SC Tel: (800) (864) Fax: (864) sales@bindicator.com Order from: C A Briggs Company; 622 Mary Street; Suite Warminster, PA Phone: Fax: ; Sales@cabriggs.com - MPR Rev. B 2016 All rights reserved. All data subject to change without notice.

3 TDR-2000 DESCRIPTION The TDR-2000 provides continuous, non-mechanical level measurement, utilizing guided wave radar technology. The TDR-2000 is particularly suited for measuring the level of solids, granules, and powders, as well as a wide range of liquids. For many applications, the TDR-2000 is an economical and superior alternative to capacitance, ultrasonic, and plumb bob technologies. HOW IT WORKS The TDR-2000 two-wire guided microwave level transmitter uses the TDR (Time Domain Reflectometry) principle. The instrument sends low power nanosecond-wide pulses along an electrically conductive rod, cable, or coaxial probe with a known propagation speed (the speed of light). As the pulse reaches the surface of the medium (altered dielectric constant Ԑr), a part of it is reflected back to the electronic module. The efficiency of the reflected signal depends on the dielectric constant (Ԑr) difference of the mediums. The reflected pulse is detected as an electrical voltage signal and is then processed by the electronics. Level distance is directly proportional to the flight time of the pulse. The measured level data is converted to 4-20 ma current and HART signals and is displayed on the LCD display. From the level data, further derived measuring values can be calculated such as volume and mass. The TDR-2000 is unaffected by the other properties of the medium as well as that of the space above it. FEATURES AND BENEFITS Flexibility for a wide range of applications Suitable for a broad range of tank sizes, geometries, and internal constructions Ideal for dirty service applications Accurate and reliable level measurement across a range of dynamic process conditions Insensitive to changes in dielectric, pressure, conductivity, vacuum, humidity, dust, viscosity, vapor, foam, ph, bulk density, temperature, or turbulence Unaffected by filling or emptying conditions such as dust, noise, and material movement Easy Installation Simple to install in new tanks or retrofit existing tanks Can be installed while tank is in service Does not require special configuration to compensate for environmental or structural conditions Low Maintenance Factory calibrated and configured Transmitter design minimizes maintenance requirements HOW TO ORDER TDR A Serial Adapter (Note 2) N = No Adapter Y = RS-422/485 Enclosure (Note 2) N = No Enclosure E = Plastic Enclosure Display Type Blank = None (Note 2) 6R0 = VAC with no relays 6R2 = VAC with two (2) relays 6H0 = VAC with no relays, with Sunbright display 6H2 = VAC with two (2) relays, with Sunbright display 7R0 = VDC with no relays 7R2 = VDC with two (2) relays 7H0 = VDC with no relays, with Sunbright display 7H2 = VDC with two (2) relays, with Sunbright display Probe Length, in inches (Note 1) Approvals A = General Purpose (IP67) D = Hazardous Location - Dust (II 1D ia IIIC T85ºC...T110ºC Da) G = Hazardous Location - Gas (II 1G Ex ia IIC or IIIB T6...T4) Voltage A = 18 VDC to 35 VDC TDR-2000 Guided Wave Radar NOTES 1. Maximum probe length is 78.8 ft (24.0 m). 2. If no display is required, leave Display Type, Enclosure and Serial Adapter blank

4 TDR-2000 SPECIFICATIONS FUNCTIONAL Operating Power 24 VDC (18 to 35 VDC) Ex Version: 24 VDC (18 to 28 VDC) Ambient Temperature -4 to 140 F (-20 to 60 C) Process Temperature Operating Pressure -22 to 212 F (-30 to 100 C) Flange: -22 to 194 F (-30 to 90 C) 580 psig (40 bar) Cable length < 33 ft. (10 m); accuracy is ± 0.8 (20 mm) Accuracy Cable length > 33 ft. (10 m); accuracy is ± 0.20% of length Dielectric Constant > 2.1 Output 4-20mA, HART Communication, terminal resistor 750 Ohm max PERFORMANCE Flexible Probe: Max of 79 ft (24.0 m) Measuring Range Deadband Top: 15.8 (40 cm) if Ԑr < 10; 11.8 (30 cm) if Ԑr > 10 Deadband Bottom: 14.2 (36 cm) Counter Weight Diameter: 1.6 (4 cm); length 10.2 (26 cm) Repeatability 0.04 (1 mm) PHYSICAL Process Connection 1½ MNPT Ingress Protection 1P67 (NEMA 4-4X) Conduit Connections (2) M20 x 1.5 and (2) ½ NPT Electrical Protection Class III Probe Materials Flexible 316 Stainless Steel Cable Enclosure Materials Aluminum with white epoxy coating Gasket Materials FPM (Viton ), FFKM Perfluoroelastomer (Kalrez 6375), EPDM Shipping Weight (Head Unit) 3.3 lb (1.5 kg) APPROVALS: ATEX MARKINGS II 1G Ex ia IIB T6...T4 Ga II 1G Ex ia IIC T6...T4 Ga II 1D Ex ia IIIC T85 C...T110 C PER THE FOLLOWING STANDARDS: MSZ EN :2013 MSZ EN :2013/A11:2014 MSZ EN :2012 T ambient = -20 C C POWER SUPPLY AND LOCAL DISPLAY The PRD1000 is a power supply and local display meter ideal for level, flow rate, temperature, or pressure transmitter applications. Available in VAC or VDC with up to two relays. It has a dual-line 6-digit display, advanced signal input conditioning, function keys, and Modbus RTU serial communications. The basic model includes an isolated 24 VDC transmitter power supply that can be used to power the input transmitter or other devices. A NEMA 4X enclosure is optional, as well as, an RS-485 serial adapter. PRD1000 in NEMA 4X Enclosure 150 Venture Boulevard Spartanburg, SC Tel: (800) (864) Fax: (864) sales@bindicator.com Order from: C A Briggs Company; 622 Mary Street; Suite Warminster, PA Phone: Fax: ; Sales@cabriggs.com - TDR Rev. F 2016 All rights reserved. All data subject to change without notice.

5 Mark-4 TM /GP-4 TM Yo-Yo TM DESCRIPTION The GP-4 TM and Mark-4 TM Yo-Yo TM sensors are designed to provide accurate, reliable inventory management information for tanks and silos. MARK-4 TM NEMA 4/7/9, shown with standard plastic weight FEATURES AND BENEFITS Silos up to 100 ft (30.5 m) Large range of silo heights can be accommodated 1cm (0.39 inches) Resolution Accurate readings Isolated 4-20 ma Output with Adjustable Span (Reversible) No loop isolator is required when connecting to a PLC or DCS RS-485 Communication MODBUS protocol GP-4 TM NEMA 4, shown with standard plastic weight The GP-4 is housed in a NEMA 4 enclosure. The Mark-4 Yo-Yo sensor is housed in a NEMA 4/7/9 enclosure. The Bindicator remote display/ programmer can request readings, monitor up to 99 GP-4 and Mark-4 sensors, and program silo parameters. The display/programmer is used to configure a single sensor or a whole system. An adjustable autotimer allows the user to set automatic measurement cycles ranging from 2 minutes to 1 week. While in operating mode, the display will show the sensor address, sensor name, measurement in the specified units, percentage, display mode and the status of the current device. The display can be used with GP-4 Display/Programmer or Bindicator ORB TM. HOW TO ORDER N 1 10 CABLE 1 = Polyester 2 = Monofilament, max 40 (12.19m) 3 = Stainless Steel (Mark 4 only) SENSING WEIGHT P = Plastic, Standard D = Stainless Steel Bob F = Stainless Steel Float S = Plastic Spike Weight LP = Low Density Plastic Weight LS = Low Density Stainless Steel Weight PB = PVC Jacketed Bob (Note 1) OUTPUT 1 = MODBUS, 4-20 ma VOLTAGE 1 = 115 VAC 2 = 230 VAC HEATER (NOTE 2) N = Without Motor Heater Y = With Motor Heater GP-4 & MARK-4 YO-YO LBY-4 = GP-4 (NEMA 4) LHY-7 = Mark-4 (NEMA 4/7/9) Note 1: Specify monofilament cable. Note 2: For operation below 32 F (0 C). SENSOR WEIGHT OPTIONS Remote Display Programmer with Keypad 4-line x 20-character backlit LCD display Programmable sensor names and ranges Enable/Disable network addresses P = Plastic, Standard S = Plastic, Spike Weight D = SS Bob

6 Mark-4 TM /GP-4 TM Yo-Yo TM SPECIFICATIONS MARK-4 TM FUNCTIONAL Operating Power Power Consumption Operating Temperature Output PERFORMANCE Repeatability Measurement Span Automatic Timer PHYSICAL Mounting Conduit Entry Air Purge Connection Enclosure Material Enclosure Rating Shipping Weight OPTIONS APPROVALS Mark-4 GP-4 MARK-4/GP-4 YO-YO 115 VAC or 230 VAC 115 VAC, 50/60 Hz, 32 watts (operating), 4 watts (quiescent) (with heater add 10 watts) 32º to 120º F (0º to 49º C); with heater -31º to 120º F (-35º to 49º C) MODBUS, Analog 4-20 ma optically isolated (user sourced) into 600 ohms max 2 cm (0.8 in) Up to 100 ft standard From 2 minutes to 9999 minutes (approx. 1 week) 3 NPT GP-4: 2 each 3 /4 NPT, Mark-4: 3 each 3 /4 NPT 1 /4 NPT GP-4: Minlon frame, low density polyethylene cover Mark-4: Polyester coated cast aluminum GP-4: NEMA 4 Mark-4: NEMA 4/7/9 GP-4:13 lbs (6 kg) Mark-4: 26 lbs (12kg) Motor Heater YoYo Display ORB FM (US) - XP Class I, Division I, Groups C and D; T5, Ta= 60º C DIP Class II, III, Division I, Groups E, F, and G; T5, Ta= 60º C; Type 4 CSA - Class I, Groups C and D; Class II, Groups E, F and G; Class III; Type 5; Type 4 ATEX FM (US) - General Purpose CE GP-4 TM

7 Display / Programmer DESCRIPTION The display/programmer allows a user to configure a single sensor or a whole system. An adjustable autotimer allows the user to set automatic measurement cycles ranging from 2 minutes to 1 week. While in operating mode, the display will show the sensor address, sensor name, measurement in the specified units, percentage, display mode and the status of the current device. FEATURES AND BENEFITS Remote Sensor Set-up and Configuration Allows end user to set-up system from any location Remote Measurement Request and Display Monitors up to 99 sensors from up to 4000 feet 4-line x 20 Character Backlit LCD Display Easy to read level, sensor name and status RS-485 Communication MODBUS protocol Optional Heater Keeps system running smoothly in temperatures below -4 F (-20 C) HOW TO ORDER LBY-4 M 0 10 HEATER (See Note 1) A = Without Heater B = 115 VAC Heater C = 230 VAC Heater COMMUNICATIONS M = MODBUS DISPLAY / PROGRAMMER Note 1: For operation below -4 F (-20 C) SYSTEM CONFIGURATION * See ORB Technical Sheet for Specifications.

8 Display / Programmer SPECIFICATIONS DIMENSIONS FUNCTIONAL Display / Programmer Powered from Yo-Yo sensor Operating Power (9-24 VDC); With optional heater, 120/240 VAC required -4 F to 158 F (-20 C to 70 C); Operating with optional heater: Temperature -40 F to 158 F (-40 C to 70 C) PHYSICAL Communication RS-485 MODBUS Optional integral modem Sensors Up to 99 Display 4 lines by 20 characters Backlit LCD display Keypad NEMA 4X soft-touch Enclosure NEMA 4X molded fiberglass polyester PERFORMANCE Wiring Requirements Belden 9842, 4 wire shielded cable Wiring Distance 4000 max Speed 115 Kbps Protocol MODBUS Interface RS-485 Internal Modem Optional 56K Modem Minlon is a registered trademark of E.I. Du Pont Belden is a registered trademark of Belden Inc. 150 Venture Boulevard Spartanburg, SC Tel: (800) (864) Fax: (864) sales@bindicator.com Order from: C A Briggs Company; 622 Mary Street; Suite Warminster, PA Phone: Fax: ; Sales@cabriggs.com - LBY Rev. G 2015 All rights reserved. All data subject to change without notice.

9 SonoTracker TM FEATURES AND BENEFITS Quick Configuration Menu driven quick set up in less than 5 minutes. Digital Connection to ORB (RS-422) Modular Design Configurable for number of sensors, relays, point level inputs, current loops, and PLC interfaces. Multiple Functions In One Unit Solids and liquid level, open channel flow, and differential level measurement. Adjusts systems parameters and pre-calibrates unit without special software. Continuous Non-Contact Level Measurement No contamination of material, no lost parts or cables, no material build-up on sensing cables/surfaces. Sentry DSP Provides stable and accurate reading under process conditions. NEMA-4X Enclosure FRP or optional stainless steel offers the right protection for your environment. Built-in Optically Isolated Serial Port Versatile interfacing for data collection, servicing and building large multi-vessel communications systems. DESCRIPTION The SonoTracker TM Ultrasonic Level System can monitor up to 16 vessels with transducers of various frequencies, and vessels of different heights and shapes and accurately measure the level of many different materials. It allows you to read levels from 1 foot to beyond 100 feet in solids, and additionally the same unit can be used for open channel flow and differential level measurements. HOW TO ORDER SON SLOT 3 CARD OPTIONS A = None C = 5 Output Relay Card D = 8 Output Relay Card E = 2 Output Relays with 1-Channel 4-20mA Card (AC Power Only) ED= 2 Output Relays with 1-Channel 4-20mA Card (AC/DC) G = 8-Channel 4-20mA Output Card (AC Power Only) H = 4-Channel 4-20mA Output Card (AC Power Only) I = 2-Channel 4-20mA Output Card (AC Power Only) N = 4 Output Relays with 2-Channel 4-20mA Card (AC Power Only) ND= 4 Output Relays with 2-Channel 4-20mA Card (AC/DC) Q = ProfiBus DP Card S = Point Level Input Card SLOT 2 CARD OPTIONS A = None B = 8 Vessel Scanner Card C = 5 Output Relay Card D = 8 Output Relay Card J = 4 Vessel Scanner Card K = 2 Vessel Scanner Card Q = Profibus DP Card S = Point Level Input Card SLOT 1 CARD OPTIONS A = None B = 8 Vessel Scanner Card J = 4 Vessel Scanner Card K = 2 Vessel Scanner Card HEATER * Y = Yes N = No ENCLOSURE TYPE A = NEMA 4X Fiberglass B = NEMA 4X Stainless Steel OPERATING VOLTAGE A = 110 VAC B = 24 VDC D = 220 VAC SONOTRACKER TM LEVEL MONITOR with Serial Output Isolator and Backlight Display * For use below -5º F (-20º C)

10 SonoTracker TM SPECIFICATIONS FUNCTIONAL SonoTracker TM 110/230 VAC (+/- 10%) 50/60 Hz Operating Power or 24 VDC Power Requirement 20 VA Operating Temperature -5º to 122º F (-20º to 50º C) Measuring Distance 1 to 100 depending on sensor PERFORMANCE Transducer Frequencies from 10 KHz to 45 KHz Compatibility Non-volatile RAM, common isolation Memory parameter storage Form C SPDT, programmable, 10 A 110 VAC, 8 A 230 VAC noninductive, 10 A 30 VDC; available as plug in modules of 2, 4, 5 and 8 relays each 4-20 ma option: Isolated 600 ohms maximum or externally powered to 1000 ohms, 12 bit resolution; Relay Output available as plug in modules of 2, 4, and 8 outputs with common isolation; must be installed in third option slot Combi-Card option: One combicard per unit; combinations are 2 relays, 1 current; or 4 relays, 2 currents 32 channel block transfer, 6 channel PLC Interface Option discreet transfers, Profibus-DP Slave PHYSICAL NEMA 4X fiberglass reinforced Enclosures polyester (FRP) or NEMA 4X Stainless Steel Large, back lit alphanumeric liquid crystal, two lines of 16 characters, Display user programmable IDs, selectable bar graph disply or engineering units formats

11 SonoTracker TM DESCRIPTION The range of sensors allows you to read levels from 1 foot to beyond 100 feet in solids. The BT-55 transducer has an extremely narrow beam angle, allowing it to be used in challenging applications. Additionally, the same unit also performs open channel flow and differential level measurements. FEATURES AND BENEFITS Versatility The transducers are designed for your specific application and environment. Available in frequencies of 14kHz, 22kHz, 24 khz and 43kHz to fit a variety of materials and distances. Accuracy 1% of rated span in approved bulk solids applications 0.25% of rated span in approved liquid applications HOW TO ORDER SON BT-26 PVC Sensor SON BT-26 PVC Sensor with TC SON200058** BT-26 Stainless Steel Sensor SON200069** BT-26 Stainless Steel Sensor with TC SON200084SVB BT-50 PVC Sensor SON200057SVB BT-50 PVC Sensor with TC SON200085* BT-55 PVC Sensor SON BT-61 PVC Sensor SON BT-61 PVC Sensor with TC SON BT-101 PVC Sensor SON BT-101 PVC Sensor with TC SON Junction Box, NEMA 4x with 5 terminal connections External temperature probe Aiming Kit (excluding BT-55) Aiming Kit (BT-55 Only) NOTES: Non-pressurized flanges with standard ANSI 150 lb bolt hole configurations are available in 3, 4, 6, 8 and 12. Use part number for sensor cable and LUC for temperature compensation cable. * This sensor not FM Approved APPROVALS Transducers are FM approved: S Class I, II, III; Division I, Groups C, D, E, F and G; T5 **3A (Transducer Specific) BT-26 Stainless Steel Sensor BT-101 PVC Sensor BT-55 PVC Sensor

12 SonoTracker TM TRANSDUCER SPECIFICATIONS Nominal Range Liquids Nominal Range Solids Minimum Range BT-26PT 25 (7.6m) 15 (4.6m) 12 (305mm) BT-26ST 25 (7.6m) 15 (4.6m) 12 (305mm) BT-61PT 50 (15.2m) 30 (9.2m) 24 (610mm) BT-50PT 50 (15.2 m) 50 (15.2 m) 36 (914mm) BT-55 BT-101PT 100 (30.5m) 125 (38.1m) 50 grains 100 plastics 100 (30.5m) 24 (610mm) 36 (914mm) Temperature Range Weight Frequency Beam Angle -40 to 160 F (-40 to 71 C) -40 to 230 F (-40 to 110 C) -40 to 160 F (-40 to 71 C) -40 to 160 F (-40 to 71 C) -40 to 160 F (-40 to 71 C) -40 to 160 F (-40 to 71 C) 1.2 lbs (0.5 kg) 1.2 lbs (0.5 kg) 3.1 lbs (1.4 kg) 5.75 lbs (2.6 kg) 13.0 lbs (5.9kg) 5.75 lbs (2.6 kg) 43KHz 43KHz 22KHz 14KHz 24KHz 14KHz 12 included 12 included 12 included 12 included 5 included 12 included TRANSDUCER MOUNTING DIMENSIONS A B BT-26PT 5.2 (132.1mm) 2.3 (58.41mm) BT-26ST 5.5 (139.7mm) 2.5 (63.5mm) BT-61PT 6.9 (175mm) 4.2 (107mm) BT-50PT 9.2 (233.7mm) 5.5 (139.7mm) BT (463.6mm) 7.12 (180.8mm) BT-101PT 9.2 (233.7mm) 5.5 (139.7mm) 1 NPT 1 NPT PT ST A B B TRANSDUCER SELECTION BY PRODUCT A 1 NPT BT-55 B A 150 Venture Boulevard Spartanburg, SC Tel: (800) (864) Fax: (864) sales@bindicator.com Order from: C A Briggs Company; 622 Mary Street; Suite Warminster, PA Phone: Fax: ; Sales@cabriggs.com - SON Rev. K 2016 All rights reserved. All data subject to change without notice.

13 Cap-Level IIA DESCRIPTION Cap-Level IIA is designed for level monitoring and control. The 4-20mA output provides a selectable dampening function to stabilize readings where severe agitation is present. Simple zero and span adjustment make calibration easy. The relay logic circuitry offers the flexibility to control multiple pumps, conveyors, and alarms. Each relay can be set to turn your equipment on and off at any selected point on the probe, without any external latching devices. Failsafe selection gives the security of fault indication and/or conveyor stop if power is lost. The probe configurations and materials offered allow you to custom fit Cap-Level IIA to your application. Designs such as the type E and H tie-down, allow use in tall silos and include a unique cable tightening adjustment. HOW TO ORDER CL 2A 4 10 FEATURES AND BENEFITS Two-wire transmitter (24 VDC) Senses practically any liquid Electronic options Rigid or flexible probes FM approved for hazardous areas Continuous 4-20mA Standard Communication Output Dampening - Standard Stabilizes readings where severe agitation is present Teflon, PVC, and 316 SS Probes and NPT or Flange Mounting Options for a wide range of applications Continuous Process Management Uninterrupted level measurement All models intrinsically safe when used with approved barriers. MODIFICATION (Note 1) A = No Lagging Extension B = With 10 SS Lagging Extension FLANGE MATERIAL 1 = None 2 = 316 SS 3 = Carbon Steel 4 = Teflon Faced 316 SS (Note 2) 5 = Teflon Faced Carbon Steel (Note 2) FLANGE OPTION A = None B = lb C = lb D = lb E = lb S = Special PROBE LENGTH (NOTE 3 & 4) PROBE TYPE A = 316 SS Solid Probe (Note 5) B = Teflon Jacketed Solid Probe D = Bare SS Cable, SS Weight (Note 5) E = Bare SS Cable, Tie Down Assembly (Note 5) H = Teflon Jacketed Cable, Tie Down Assembly I = Teflon Jacketed Cable, Teflon Jacketed Weight M = PVC Jacketed Solid Probe N = Teflon Jacketed Solid With 1 Sanitary Mount P = 316 SS Solid with 1 Sanitary Mount (Note 5) Q = Teflon Jacketed Solid Probe With 2 Sanitary Mount VOLTAGE 4 = 24 VDC (External Loop Power Supply Required) ENCLOSURE G = General Purpose, NEMA 4X R = NEMA 4X, Remote Cable Required SERIES-IIA 2A = 2 Wire Analog (4-20mA) CAP-LEVEL IIA Note 1. Lagging assembly is used for high temperature applications. Note 2. All models are intrinsically safe when used with approved barriers. Note 3. Maximum standard length for solid probes is 14 (4.2m). For probes exceeding this length consult factory. Note 4. Maximum standard length for cable probes is 100 (30.5m). For probes exceeding this length contact factory. Note 5. For dry or non-conductive materials only.

14 Cap-Level IIA SPECIFICATIONS PROBE APPLICATION FUNCTIONAL Power Output Drive Capability Calibration Capacitance Range Repeatability Sensing System PHYSICAL Enclosure Enclosure Temperature Length APPROVALS VDC (27 VDC max. for LS operation) 4-20mA VDC (varies with voltage) Zero and span with frequency selection 0 pf to 4000 pf nominal ±1% of span (constant dielectric) High frequency capacitance with digital comparator NEMA 4X, aluminum with corrosion resistant polyester coating -40 F to 120 F (-40 C to 49 C) (lagging assembly for higher temperature) As specified - Types A, B, M, N, P, Q: 167 (4175mm) maximum; Types D, E, H, I: 1200 (36000mm) maximum Hazardous Location: FM, Intrinsically safe, Class I, II, III, Div I, Groups C, D, E, F & G Type 4, T4A Probe Type Mount Standard Material A ¾ NPT 316 SS** B ¾ NPT Teflon /SS Pressure (Max) D 1¼ NPT 316 SS** Atmospheric E 1¼ NPT 316 SS** Atmospheric H 1¼ NPT Teflon /SS Atmospheric I 1¼ NPT Teflon /SS M ¾ NPT PVC/SS N 1 Sanitary Teflon /SS P 1 Sanitary 316 SS Q 2 Sanitary Teflon /SS Temp. (Max) 140 F (60 C) ** Probe types A, D, E non-conductive media only. Use auxiliary ground rod or stilling well (reference ground) in fiberglass or lined vessels. Teflon is a registered trademark of E.I. Du Pont, All rights reserved. TYPE B PROBE 150 Venture Boulevard Spartanburg, SC Tel: (800) (864) Fax: (864) sales@bindicator.com Order from: C A Briggs Company; 622 Mary Street; Suite Warminster, PA Phone: Fax: ; Sales@cabriggs.com - SCL Rev. E 2012 All rights reserved. All data subject to change without notice.

15 Cap-Level II DESCRIPTION Cap-Level II is designed for level monitoring and control. The 4-20mA output provides a selectable dampening function to stabilize readings where severe agitation is present. Simple zero and span adjustment make calibration easy. The relay logic circuitry offers the flexibility to control multiple pumps, conveyors and alarms. Each relay can be set to turn your equipment on and off at any selected point on the probe - without any external latching devices. Failsafe selection gives the security of fault indication and/or conveyor stop if power is lost. The probe configurations and materials offered allow you to custom fit Cap-Level II to your application. Designs such as the type E and type H tie-down, allow use in tall silos and include a unique cable adjustments. HOW TO ORDER CL 30 FEATURES AND BENEFITS Continuous 4-20mA Standard Communication Output Dampening - Standard Stabilizes readings where severe agitation is present Teflon, PVC, 316 SS Probes and NPT or Flange Mounting Options for a wide range of applications Continuous Process Management Uninterrupted level measurement DESIGN LEVEL (Assigned by Factory) PROBE LENGTH (Specify inches, see Notes 1, 2) PROBE TYPE A = 316 SS Solid Probe (See Note 3) B = Teflon Jacketed Solid Probe D = Bare SS Cable, SS Weight (See Note 3) E = Bare SS Cable, Tie Down Assmbly (See Note 3) H = Teflon Jacketed Cable, Tie Down Assembly I = Teflon Jacketed Cable, Teflon Jacketed Weight M = PVC Jacketed Solid Probe N = Teflon Jacketed Solid With 1 Sanitary Mount P = 316 SS Solid with 1 Sanitary Mount (See Note 3) Q = Teflon Jacketed Solid Probe With 2 Sanitary Mount VOLTAGE 1 = 120 VAC 2 = 240 VAC ENCLOSURE G = General Purpose - NEMA 4X X = Explosion-Proof - NEMA 7/9 (See Note 4) SERIES 3 = Continuous with No Relays 4 = Continuous with 1 Relay 5 = Continuous with 2 Relays CAP-LEVEL II Note 1. Note 2. Note 3. Note 4. Maximum standard length for solid probes is 167 (4242mm). For probes exceeding this length contact factory. Maximum standard length for cable probes is 1200 (30480mm). For probes exceeding this length contact factory. For dry or non-conductive materials only. Type B probe only.

16 Cap-Level II SPECIFICATIONS FUNCTIONAL Operating Power 120 VAC, 240 VAC Power Consumption 8 Watts Operating Temperature -40º to 160º F (-40º to 71º C) PERFORMANCE Hysteresis 2.5% of span min, 100% max Analog Output 4-20mA into 400 Ohms max Relay Output SPDT, VAC Accuracy 1% FS with Constant Dielectric Analog: course and fine zero/ span, non-interacting relays: hi, low Calibration setpoints and hysteresis set as % of span PHYSICAL NEMA 4X or NEMA 7/9 aluminum Enclosure with corrosion resistant polyester coating As specified for Types A, B, M, N, P, Length Q:167 (4157 mm), Types D, E, H, I: 1200 (36000 mm) APPROVALS General Purpose: CSA; Type 4 PROBE APPLICATION Probe Type Mount Standard Material A ¾ NPT 316 SS** B ¾ NPT Teflon /SS Pressure (Max) D 1¼ NPT 316 SS** Atmospheric E 1¼ NPT 316 SS** Atmospheric H 1¼ NPT Teflon /SS Atmospheric I 1¼ NPT Teflon /SS M ¾ NPT PVC/SS N 1 Sanitary Teflon /SS P 1 Sanitary 316 SS** Q 2 Sanitary Teflon /SS Temp. (Max) 140 F (60 C) ** Probe types A, D, E - non-conductive media only. Consult factory when mounting in fiberglass or lined vessels. Teflon is a registered trademark of E.I. Du Pont, All rights reserved. Hazardous Location: CSA; Class I, Groups C and D 150 Venture Boulevard Spartanburg, SC Tel: (800) (864) Fax: (864) sales@bindicator.com Order from: C A Briggs Company; 622 Mary Street; Suite Warminster, PA Phone: Fax: ; Sales@cabriggs.com - SCL Rev. E 2012 All rights reserved. All data subject to change without notice.