Advance PTNC210604MD. Wideband LDMOS Two-stage Integrated Power Amplifier 20 W + 40 W, 28 V, MHz. Description. Features

Transcription

1 Advance PTNC210604MD Wideband LDMOS Two-stage Integrated Power Amplifier 20 W + 40 W, 28 V, MHz Description The PTNC210604MD is a wideband, two-stage, LDMOS integrated power amplifier. It incorporates internal matching for operation from 1805 MHz to 2200 MHz, and dual independent outputs with 20 W and 40 W of output power each. It is available in a 14-lead plastic overmold package with gull wing leads. Features Advance Specification Data Sheets describe products that are being considered by Wolfspeed for development and market introduction. The target performance shown in Advance Specifications is not final and should not be used for any design activity. Please contact Wolfspeed about the future availability of these products. On-chip matching for broadband operation Integrated ESD protection Integrated temperature compensation Pb-free and RoHS-compliant Low thermal resistance Pb-free and RoHS compliant PTNC210604MD Package PG-HB1DSO-14-1 Target RF Characteristics Single-carrier WCDMA Specifications (tested in Infineon Doherty test fixture) V DD = 28 V, I DQ1A = 63 ma, I DQ2A = 150 ma, I DQ1B = 40 ma, V GS2B = 2.6 V, P OUT = 10 W avg, ƒ = 2200 MHz, 3GPP WCDMA signal, channel bandwidth = 3.84 MHz, peak/average = % CCDF Characteristic Symbol Min Typ Max Unit Gain G ps 27.5 db Drain Efficiency h D 37 % Adjacent Channel Power Ratio ACPR 36 dbc All published data at T CASE = 25 C unless otherwise indicated ESD: Electrostatic discharge sensitive device observe handling precautions!

2 Advance PTNC210604MD 2 DC Characteristics Stage 1 Conditions Symbol Min Typ Max Unit Drain Leakage Current V DS = 28 V, V GS = 0 V I DSS 0.1 µa V DS = 60 V, V GS = 0 V I DSS 1.0 µa Gate Leakage Current V GS = 1 V, V DS = 0 V I GSS 0.1 µa On-State Resistance (Main) V GS = 10 V, V DS = 0.1 V R DS(on) 5 W (Peak) V GS = TBD V, V DS = 0.1 V R DS(on) TBD W Operating Gate Voltage (Main) V DS = 28 V, I DQ1 = 63 ma V GS1 2.9 V Operating Gate Voltage (Peak) V DS = 28 V, I DQ1 = 40 ma V GS V Fixture Operating Gate Voltage (Main) V DS = 28 V, I DQ1 = 63 ma V GS1 5.4 V (Peak) V DS = 28 V, I DQ1 = 40 ma V GS V DC Characteristics Stage 2 Conditions Symbol Min Typ Max Unit Drain-Source Breakdown Voltage V GS = 0 V, I DS = 200 ma V( BR)DSS 65 V Drain Leakage Current V DS = 28 V, V GS = 0 V I DSS 0.1 µa V DS = 60 V, V GS = 0 V I DSS 1.0 µa Gate Leakage Current V GS = 1 V, V DS = 0 V I GSS 0.1 µa On-State Resistance (Main) V GS = 10 V, V DS = 0.1 V R DS(on) 1.5 W (Peak) V GS = TBD V, V DS = 0.1 V R DS(on) TBD W Operating Gate Voltage (Main) V DS = 28 V, I DQ2 = 150 ma V GS V (Peak) V DS = 28 V, I DQ2 = 0 ma V GS V Fixture Operating Gate Voltage (Main) V DS = 28 V, I DQ2 = 150 ma V GS V (Peak) V DS = 28 V, I DQ2 = 0 ma V GS V Maximum Ratings Parameter Symbol Value Unit Drain-Source Voltage V DSS 65 V Gate-Source Voltage V GS 6 to +12 V Operating Voltage V DD 0 to +32 V Junction Temperature T J 225 C Storage Temperature Range T STG 65 to +150 C

3 p t m c m d _ P D _ Advance PTNC210604MD 3 Thermal Characteristics Parameter Symbol Value Unit Thermal Resistance Stage 1 (T CASE = 70 C ) R qjc TBD C/W Stage 2 (T CASE = 70 C ) R qjc TBD C/W Moisture Sensitivity Level Level Test Standard Package Temperature Unit 3 IPC/JEDEC J-STD C Ordering Information Type and Version Order Code Package Shipping PTNC210604MD V1 R5 TBD PG-HB1DSO-14-1 Tape & Reel, 500 pcs Pinout Diagram (top view) VD1 A 1 VG2 A 2 VG1 A RFIN A VD2/RFOUT A RFIN B VG1 B VD2/RFOUT B VG2 B 11 VD1B 12 Source: plated copper heat slug on backside of package Lead connections for PTNC210604MD

4 PG-HB1DSO-14-1_01_ PG-HB1DSO-14L_01_ Advance PTNC210604MD 4 Package Outline Specifications Package PG-HB1DSO-14-1 (top view) 2X X X X X MAX Y X X X Z ± Z (5:1) 0 MIN X X STAND OFF R ± Diagram Notes unless Notes unless otherwise specified: VIEWÊY 1. Mold/Dam 1. Mold/dam Bar/Metal bar/metal protusion protrusion of 0.30mm of 0.30 max mm per max side per not side included. not included. 2. Metal 2. protrusion Metal protrusions are connected are connected to source to and source shall and not shall exceed not exceed 0.10mm 0.10 max. mm max. 3. Fillets 3. Fillets and radii: and all radii: all are radii 0.3 are mm 0.30 max. mm max x Interpret Interpret dimensions dimensions and tolerances and tolerances per ISO per ISO Dimensions 5. Dimensions are mm. are mm. 6. All tolerances 6 All tolerances ± 0.1mm ± 0.1 unless mm unless specified specified otherwise. otherwise. 7. All metal 7. All surfaces metal surfaces pre-plated, pre-plated, except except area of area cut. of cut. 8. Lead 8. thickness: Lead thickness: 0.25 mm mm. 9. Gold 9. plating Gold plating thickness: thickness: 0.25 micron 0.25 micron [10 microinch] max. max

5 PG-HB1DSO-14-1_01_ Advance PTNC210604MD 5 Package Outline Specifications Package PG-HB1DSO-14-1 (bottom view) VIEWÊY x Diagram Notes unless otherwise specified: 1. Mold/dam bar/metal protrusion of 0.30 mm max per side not included. 2. Metal protrusions are connected to source and shall not exceed 0.10 mm max. 3. Fillets and radii: all radii are 0.30 mm max. 4. Interpret dimensions and tolerances per ISO Dimensions are mm. 6 All tolerances ± 0.1 mm unless specified otherwise. 7. All metal surfaces pre-plated, except area of cut. 8. Lead thickness: 0.25 mm. 9. Gold plating thickness: 0.25 micron max.

6 Advance PTNC210604MD 6 Revision History Revision Date Data Sheet Type Page Subjects (major changes since last revision) Advance All Data Sheet reflects advance specification for product development Advance All Updated single-carrier specs, DC characteristics, converted to Wolfspeed Data Sheet For more information, please contact: 4600 Silicon Drive Durham, North Carolina, USA Sales Contact RFSales@wolfspeed.com RF Product Marketing Contact RFMarketing@wolfspeed.com Notes Disclaimer Specifications are subject to change without notice. Cree, Inc. believes the information contained within this data sheet to be accurate and reliable. However, no responsibility is assumed by Cree for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Cree. Cree makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose. Typical parameters are the average values expected by Cree in large quantities and are provided for information purposes only. These values can and do vary in different applications and actual performance can vary over time. All operating parameters should be validated by customer s technical experts for each application. Cree products are not designed, intended or authorized for use as components in applications intended for surgical implant into the body or to support or sustain life, in applications in which the failure of the Cree product could result in personal injury or death or in applications for planning, construction, maintenance or direct operation of a nuclear facility. Copyright 2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Wolfspeed and the Wolfspeed logo are trademarks of Cree, Inc.