Characteristic Condition Min. Typ. Max. Unit. Response time 3 µs Output voltage swing: VOM- VOM+ 0.4 V s - 0.4

Transcription

1 Installation Instructions for the SS49 Series Linear Hall-Effect Sensor ICs PK 8884 SOLDERING INSTRUCTIONS NOTICE Do not wave solder surface mount sensor ICs (catalog listings with suffixes -S or -SP). Wave soldering may negatively affect sensor performance and reliability, and will void Honeywell s warranty. Surface mount (catalog listings with suffixes -S or -SP): Use infrared reflow process with active flux, lead-free solder. Do not exceed peak temperature of 245 C [473 F] for a maximum of 1 seconds. Table 1. General Specifications for All Catalog Listings. Through-hole leads: Wave solder at 25 C to 26 C [482 F to 5 F] for a maximum of three seconds. Burrs are allowed only if full length of leads will pass through,68 mm [.27] dia. hole. CLEANING INSTRUCTIONS CAUTION PRODUCT DAMAGE Use agitated rinse, not pressure wash, in order to avoid forcing contaminants into the sensor package. Failure to comply with these instructions may result in product damage. Supply current T A = 25 C [77 F] ma Output current: sourcing sinking sinking V s > V s > V s > ma Response time 3 µs Output voltage swing: VOM- VOM+ -B applied +B applied.4 V s V s -.2 V Supply voltage T A = -4 C to 125 C [-4 F to 257 F] V Operating temperature -4 [4] 15 [32] C [ F] Soldering temperature and time wave soldering process: 25 C to 26 C [482 F to 5 F] for 3 s max. infrared reflow process: peak temperature 245 C [473 F] for 1 s max. Table 2. Absolute Maximum Specifications for All Catalog Listings Characteristic Symbol Condition Min. Typ. Max. Unit Supply voltage V s V Output voltage V out V sourcing or Output current I out 1 ma sinking Operating temperature T A C [ F] Storage temperature T S V s = C [ F] NOTICE Absolute maximum ratings are the extreme limits the device will momentarily withstand without damage to the device. Electrical and mechanical characteristics are not guaranteed if the rated voltage and/or currents are exceeded, nor will the device necessarily operate at absolute maximum ratings. NOTICE The magnetic field strength () required to cause the switch to change state (operate and release) will be as specified in the magnetic characteristics. To test the switch against the specified limits, the switch must be placed in a uniform magnetic field. CAUTION ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN OR HANDLE EXCEPT AT A STATIC FREE WORKSTATION ESD SENSITIVITY: CLASS 3 Sensing and Internet of Things

2 SS49 Series 2 Sensing and Internet of Things PK 8884 Table 3. Specifications for Catalog Listing SS494B (V s = 5. V with 4.7 k output to minus, T A = -4 C to 125 C [-4 F to 257 F]) B limits for linear operation Linearity B = -6 to +6 B = -375 to % of span Sensitivity T A = 25 C [77 F] mv/ Null T A = 25 C [77 F] V T A = 25 C to 15 C [77 F to 32 F] B = ; T A = -4 C to 125 C [-4 F to 257 F] B = ; T A = 125 C to 15 C [257 F to 185 F] Table 4. Specifications for Catalog Listings Beginning with SS495 (V s = 5. V with 4.7 k output to minus, T A = -4 C to 125 C [-4 F to 257 F]) SS495A B limits for linear operation Linearity B = -6 to % of span Sensitivity T A = 25 C [77 F] mv/ Null T A = 25 C [77 F] V T A= 25 C to 15 C [77 F to 32 F] SS495A1 B limits for linear operation Linearity B = -6 to % of span Sensitivity T A = 25 C [77 F] mv/ Null T A = 25 C [77 F] V T A= 25 C to 15 C [77 F to 32 F] SS495A2 B limits for linear operation Linearity B = -6 to % of span Sensitivity T A = 25 C [77 F] mv/ Null T A = 25 C [77 F] V T A= 25 C to 15 C [77 F to 32 F] SS495B B limits for linear operation Linearity B = -6 to % of span Sensitivity T A = 25 C [77 F] mv/ Null T A = 25 C [77 F] V T A= 25 C to 15 C [77 F to 32 F]

3 SS49 Series PK 8884 Table 5. Specifications for Catalog Listings Beginning with SS496 (V s = 5. V with 4.7 k output to minus, T A = -4 C to 125 C [-4 F to 257 F]) B limits for linear operation SS496A Linearity B = -75 to % of span Sensitivity T A = 25 C [77 F] mv/ Null T A = 25 C [77 F] V B limits for linear operation T A= 25 C to 125 C [77 F to 257 F] SS496A Linearity B = -75 to % of span Sensitivity T A = 25 C [77 F] mv/ Null T A = 25 C [77 F] V B limits for linear operation T A= 25 C to 125 C [77 F to 257 F] T A= 125 C to 15 C [257 F to 32 F] SS496B Linearity B = -75 to % of span Sensitivity T A = 25 C [77 F] mv/ Null T A = 25 C [77 F] V T A= 25 C to 15 C [77 F to 32 F] Figure 1. Block Diagram Figure 2. Maximum Supply Voltage vs Temperature 1.5 Hall-effect Sensor IC Trigger Circuit and Amplifier Vsupply (+) Output (O) Ground (-) 5.5 Acceptable operating region 125 [257] Ambient Temperature ( C [ F]) 15 [32] Figure 3. Transfer Characteristics: Typical Output Voltage SS494X SS495X SS496X Magnetic Range () Magnetic Range () Magnetic Range () Sensing and Internet of Things 3

4 SS49 Series PK 8884 Figure 4. SS49 Series Flat TO-92-Style Mounting and Dimensional Drawings (For reference only: mm/[in].) A: Straight Standard Leads Sensor IC, Bulk Pack B: Straight Long Leads Sensor IC, Bulk Pack 4,6 [.16] 2,5 [.98],76 [.3] 1,74 [.69] [.62] N S,46 [.118] 3, [.118] 4,6 [.16] 2,5 [.98],76 [.3] 1,74 [.69] [.62] N S 3, [.118] 3X,56 Max. 3X,56 Max. 15,5-14,4 [ ] 18,7 [.74] + - 2X 1,27 [.5] Note: Ensure the minimum hole size in the PCB is,68 mm [.27] dia. based on the IPC 2222 Level B standard. C. Formed Leads Sensor IC, Ammopack Tape-in-Box 4,6 [.16] 2,5 [.98],76 [.3] 2X 3,35 [.13] [.62] 3, [.118] 15,5-14,4 [ ] 2, [.787] 11, [.433] Adhesive tape + - 2X 1,27 [.5] Sensor 24,5 Max. [.2] 6, [.236] 9,1 [.354],55 Max. 1,42 Max. [.56] 6,35 [.25] 12,7 [.5] ø4, [.157] 18, [7,9] + - 2X 2,54 [.1],56 Max. D. Straight Leads Sensor IC, Ammopack Tape-in-Box (See Figure 5.A. for individual sensor IC dimensions.) Adhesive tape Sensor 24,5 Max. [.2] 11, [.433] 2, [.787] 6, [.236] 9,1 [.354] 18, [7,9],55 Max. 1,42 Max. [.56] 6,35 [.25] 12,7 [.5] ø4, [.157] 4 Sensing and Internet of Things

5 SS49 Series PK 8884 Figure 4. SS49 Series Flat TO-92-Style Mounting and Dimensional Drawings (continued) E. Surface Mount Sensor IC, Bulk Pack 4,6 [.16] 2,5 [.98] + - 2X 1,27 [.5],76 [.3] 1,74 [.69] 3,18 [.125] [.62] N S 3X,56 Max. 3, [.118] 1,52 [.6] F. Surface Mount Sensor IC, Pocket Tape and Reel (See Figure 5.E. for individual sensor IC dimensions.),41 Max. [.6] 4, [.157] 2, [.79] 8, [.315] ø1,5 [.59] A 1,75 [.69] 6,6 [.26] 5,5 [.217] 12, [.472] 1,7 [.67] Section A-A ø33,2 [1.3],1 [.4] Top cover tape 4,41 [.174] A 12,2 [.48] Measured at hub 18,39 Max. [.724] Measured at hub ø5, [1.97] 1,5 Min. [.59] Drive spokes ø13, ø178 [.512] [7.1] Arbor hole Sensing and Internet of Things 5

6 WARNING PERSONAL INJURY DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. Warranty/Remedy Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship during the applicable warranty period. Honeywell s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgement or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items that Honeywell, in its sole discretion, finds defective. The foregoing is buyer s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. While Honeywell may provide application assistance personally, through our literature and the Honeywell web site, it is buyer s sole responsibility to determine the suitability of the product in the application. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this writing. However, Honeywell assumes no responsibility for its use. For more information Honeywell Sensing and Internet of Things services its customers through a worldwide network of sales offices and distributors. For application assistance, current specifications, pricing or the nearest Authorized Distributor, visit sensing.honeywell.com or call: Asia Pacific Europe +44 () USA/Canada Honeywell Sensing and Internet of Things 968 Old Bailes Road Fort Mill, SC PK EN 7 6/ Honeywell International Inc.