XPC. Xenus Compact CANopen. digital servo drive for brush & brushless motors

Transcription

1 digital servo drive for brush & brushless motors Control Modes Profile Position-Velocity-Torque, Interpolated Position, Homing Indexer, Point-to-Point, PVT Camming, Gearing Command Interface CANopen ASCII and discrete I/O Stepper commands ±0V position/velocity/torque PWM velocity/torque command Master encoder (Gearing/Camming) Communications CANopen RS-232 Feedback Incremental Digital quad A/ encoder Analog sin/cos encoder Panasonic Incremental A Aux. encoder / encoder out Absolute SSI EnDat 2. & 2.2 Absolute A Tamagawa Absolute A Panasonic Absolute A Format Sanyo Denki Absolute A iss (&C) Other Digital Halls I/O Digital 6 High-speed inputs Motor over-temp input 4 Opto-isolated inputs High-speed output 3 Opto-isolated outputs Opto-isolated motor brake output I/O Analog Reference input, 2-bit Safe Torque Off (STO) SIL 3, Category 3, PL d Dimensions: in [mm] 7.54 x 4.55 x 2.3 [9.4 x 5.6 x 54.] Model Ic Ip Vac ~ ~ ~240 Add -R to the part number for resolver feedback description sets new levels of performance, connectivity, and flexibility. CANopen communication provides a widely used cost-effective industrial bus. A wide range of absolute encoders are supported. High resolution A/D converters ensure optimal current loop performance. oth isolated and high-speed non-isolated I/O are provided. For safety critical applications, redundant power stage enable inputs can be employed. P/N Rev 03 Page of 30

2 general specifications Test conditions: Wye connected load: 2 mh line-line. Ambient temperature = 25 C. Power input = 230 Vac, 60 Hz, Ø MODEL Output CURRENT Peak Current 9 (6.4) 2 (8.5) 5 (0.6) Adc (Arms, sinusoidal) Peak time s Continuous current 3 (2.2) 6 (4.24) 7.5 (5.3) Adc (Arms, sinusoidal) INPUT POWER Mains voltage, phase, frequency 00~240 00~240 00~240 Vac, ±0%, Ø or 3Ø, 47~63 Hz Maximum Mains Current, (Note 2) Arms Ø Arms 3Ø 24 Vdc Control power 20~32 Vdc Required for operation (Note 3_ 7.5 W (Typ, no load on outputs), 8 W, (Max, both 500 ma) DIGITAL CONTROL Digital Control Loops Current, velocity, position. 00% digital loop control Sampling rate (time) Current loop: 6 khz (62.5 µs), Velocity & position loops: 4 khz (250 µs) us voltage compensation Changes in bus or mains voltage do not affect bandwidth Minimum load inductance 200 µh line-line Resolution 2-bit capture of U & V phase currents command inputs CANopen Profile Position-Velocity-Torque, Interpolated position, Homing Stand-alone mode Analog torque, velocity, position reference ±0 Vdc, 2 bit resolution Dedicated differential analog input Digital position reference Pulse/Direction, CW/CCW Stepper commands (4 MHz maximum rate) Quad A/ Encoder 2 M line/sec, 8 Mcount/sec (after quadrature) Digital torque & velocity reference PWM, Polarity PWM = 0% - 00%, Polarity = /0 PWM 50% PWM = 50% ±50%, no polarity signal required PWM frequency range khz minimum, 00 khz maximum PWM minimum pulse width 220 ns Indexing Up to 32 sequences can be launched from inputs or ASCII commands. Camming Up to 0 CAM tables can be stored in flash memory ASCII RS-232, 9600~5,200 aud, 3-wire, RJ- connector DIGITAL inputs [IN,2] Digital, Schmitt trigger,.5 µs RC filter, 24 Vdc compatible, 5 kω programmable pull-up/downs to 5 Vdc/ground, Vt 3.5 Vdc, VT-.3 Vdc [IN3,4,5,6] Programmable as 4 single-ended or 2 differential pairs, 00 ns RC filter, 5 Vdc typical, 2 Vdc max 0 kω programmable pull-up/down per input to 5 Vdc/ground, SE: Vin-LO 2.3 Vdc, Vin-HI 2.7 Vdc, VH = 45 mv typ, DIFF: Vin-LO 200 mvdc, Vin-HI 200 mvdc, VH = 45 mv typ, [IN7,8,9,0] Opto-isolated, single-ended, ±5~30 Vdc compatible, bi-polar, with common return to 24V or ground Rated impulse 800 V, Vin-LO 6.0 Vdc, Vin-HI 0.0 Vdc, Input current ±3.6 ±24 Vdc, typical Maximum working voltage with respect to signal ground: 32 Vdc [IN] Motor overtemp signal on feedback connector, Schmitt trigger, 24 Vdc compatible 330 µs RC filter, 4.99k pullup to 5 Vdc, Vt 3.5 Vdc, VT-.3 Vdc Programmable for other functions if not used for Motemp analog input [AIN±] Differential, ±0 Vdc, 5.06 kω input impedance, 2-bit resolution safe torque off (sto) Function PWM outputs are inactive and current to the motor will not be possible when the STO function is asserted Standard Designed to IEC-6508-, IEC , IEC , ISO Safety Integrity Level SIL 3, Category 3, Performance level d Inputs 2 two-terminal: STO-IN,STO-IN-, STO-IN2, STO-IN2- Type Opto-isolators, 24V compatible, Vin-LO 6.0 Vdc or open, Vin-HI 5.0 Vdc, Input current (typical) STO-IN: 9.0 ma, STO-IN2: 4.5 ma Response time 2 ms from Vin 6.0 Vdc to interruption of energy supplied to motor Reference Xenus Plus Compact STO Manual RS-232 PORT s RxD, TxD, Gnd in 6-position, 4-contact RJ- style modular connector, non-isolated Mode Full-duplex, DTE serial communication port for drive setup and control, 9,600 to 5,200 baud Protocol inary and ASCII formats digital outputs [OUT~3] [OUT4] [OUT5] CAN PORTS Format Protocol 5V outputs Number Ratings Opto-isolated SSR, two-terminal, 300 ma max, 24 V tolerant, series Ω resistor, 36 V Zener flyback diode Rated impulse 800 V High-speed CMOS buffer, max, ±8 ma into 560 Ω (minimum) Motor brake control: opto-isolated, current-sinking with flyback diode to 24 Vdc, Adc max Dual RJ-45 receptacles, isolated from signal ground, max working voltage with respect to signal ground: 32 Vdc CANopen CiA-402 2: out on the feedback connector (), out2 on the control connector (J6) for the multi-mode encoder ma each output, 000 ma total for both outputs, thermal and overload protected Notes:. rake output is programmable as motor brake, or as general purpose digital output 2. The actual mains current is dependent on the mains voltage, and motor load and operating conditions. The Maximum Mains Currents shown above occur when the drive is operating from the maximum input voltage and is producing the rated peak and continuous output currents at the maximum output voltage. P/N Rev 03 Page 2 of 30

3 general specifications status indicators Drive Status icolor LED, drive status indicated by color, and blinking or non-blinking condition NET Status RUN/ERR LEDs, status of CANopen bus indicated by color and blink codes to CAN Indicator Specification REGENERATION Operation Solid state switch drives 60 W internal regen resistor us Capacitance 940 µf Continuous Power Capability 20 W Cut-In Voltage HV > 390 Vdc ±2 Vdc Regen output is on, regen resistor is dissipating energy Drop-Out Voltage HV < 380 Vdc ±2 Vdc Regen output is off, regen resistor not dissipating energy protections AC Mains Loss Loss of mains power between L & L2 is detected HV Overvoltage HV > 400 Vdc Drive PWM outputs turn off until HV is less than 400 Vdc HV Undervoltage HV < 60 Vdc Drive PWM outputs turn off until HV is greater than 60 Vdc Drive over temperature IGT > 85 C ±3 C Drive PWM outputs turn off until IGT temperature is below 85 ºC Short circuits Motor: Output to output, output to ground, output to HV, internal PWM bridge faults Regen: Regen to ground, Regen- to HV I 2 T Current limiting Programmable: continuous current, peak current, peak time Motor over temperature [IN] input programmable to disable drive when motor sensor resistance increases Feedback loss Programmable to detect loss of A OR encoder channels, or loss of A OR OR X channels Command Loss CANopen master stops cyclical updates, network cable is unplugged Programmable as a latching fault 24V Reversed Polarity Reversing the 24V connections (J3-4 & J3-) will not damage the drive MECHANICAL & ENVIRONMENTAL Size 7.54 x 4.55 x 2.3 [9.4 x 5.6 x 54.] Weight 2.2 lb [.0 kg] Ambient temperature 0 to 45 C operating, -40 to 85 C storage Altitude 2000 m (6560 ft) Humidity 0% to 95%, non-condensing Contaminants Pollution degree 2 Vibration 2 g peak, 0~500 Hz (sine), IEC Shock 0 g, 0 ms, half-sine pulse, IEC Cooling Internal fan allows operation at rated continuous current to 45 C ambient agency standards conformance Standards and Directives Functional Safety IEC 6508-:200, IEC :200, IEC :200, IEC : 200 (SIL 3) Directive 2006/42/EC (Machinery) ISO 3849-:205 (Cat 3, PL d) IEC :2007 (SIL3) Reference: Xenus Plus Compact STO Manual (6-0553) Product Safety Directive 204/35/EU (Low Voltage) IEC :2007 EMC Directive 204/30/EU (EMC) IEC :2004/A:20 Restriction of the Use of Certain Hazardous Substances () Directive 20/65/EU ( II) Approvals UL and cul recognized component to: UL , st Ed. UL Functional Safety Certification to: IEC 6508-:200, IEC :200 (SIL 3) ISO 3849-:205, IEC :2007, UL :202 (Cat 3, PL d) P/N Rev 03 Page 3 of 30

4 general specifications feedback Incremental: Digital Incremental Encoder Analog Incremental Encoder Absolute: SSI Quadrature signals, (A, /A,, /, X, /X), differential (X, /X Index signals not required) 5 MHz maximum line frequency (20 M counts/sec), MAX3097 differential line receiver 2 Ω terminators between A & /A, & / inputs, 30 Ω between X & /X input Sin/cos format (Sin, Sin-, Cos, Cos-), differential, Vpeak-peak ±20%, ServoTube motor compatible W > 300 khz, 2 Ω terminating resistors between Sin & Sin-, Cos & Cos- inputs 2-bit resolution, W > 300 khz, with zero-crossing detection Clock (X, /X), Data (S, /S) signals, 4-wire, Clock is output from, Data is input from encoder 30 Ω terminator between X & /X outputs, 22 Ω between S & /S inputs kω pull-ups to 5 Vdc on X & S, kω pull-downs to Sgnd on /X & /S EnDAT Clock (X, /X), Data (S, /S), Sin/Cos (Sin, Sin-, Cos, Cos-) signals Absolute A, Tamagawa Absolute A, Panasonic Absolute A Format, Sanyo Denki Absolute A SD, SD- (S, /S) signals, 2.5 or 4 MHz, 2-wire half-duplex communication Position feedback: 3-bit resolution per rev, 6 bit revolution counter (29 bit absolute position data) Status data for encoder operating conditions and errors iss (&C) MA, MA- (X, /X), SL, SL- (S, /S) signals, 4-wire, Clock output from, Data is input from encoder X & S channels for absolute encoders use ISL378 bi-directional line driver/receivers Resolver (-R option) Type rushless, single-speed, : to 2: programmable transformation ratio Resolution 4 bits (equivalent to a 4096 line quadrature encoder) Reference frequency 8.0 khz Reference voltage 2.8 Vrms, auto-adjustable by the drive to maximize feedback Reference maximum current 00 ma Maximum RPM 0,000 Halls Digital: Analog: U, V, W: Single-ended, 20 electrical phase difference between U-V-W signals, Schmitt trigger, µs RC filter, 24 Vdc compatible, 0 kω pull-up to 5 Vdc Vt = 2.5~3.5 Vdc, VT- =.3~2.2 Vdc, VH = 0.7~.5 Vdc U & V: Sin/cos format (Sin, Sin-, Cos, Cos-), differential, Vpeak-peak ±20%, ServoTube motor compatible W > 300 khz, 2 Ω terminating resistors between Sin & Sin-, Cos & Cos- inputs 2-bit resolution, W > 300 khz, with zero-crossing detection multi-mode encoder port As Input See Digital Incremental Encoder above for electrical data on A,, & X channels, or Absolute encoders using X or S channels. No terminators on A & channels, X & S channels as shown above As Emulated Output Quadrature A/ encoder emulation with programmable resolution to 4096 lines (65,536 counts) per rev from analog sin/cos encoders or absolute encoders. A/ outputs use ISL378 line drivers. A, /A,, /, outputs from ISL378 differential line driver, X, /X, S, /S outputs from ISL378 driver As uffered Output Digital A//X encoder signals from primary digital encoder are buffered by ISL378 line drivers, 5 MHz max 5V outputs Number 2: out on the feedback connector (), out2 on the control connector (J6) for the multi-mode encoder Ratings ma each output, 000 ma total for both outputs, thermal and overload protected indicators: drive state The AMP bi-color LED gives the state of the drive. Colors do not alternate, and can be solid ON or blinking. When multiple conditions occur, only the top-most condition will be displayed. When that condition is cleared the next one below will shown. ) Red/linking = Latching fault. Operation will not resume until drive is Reset. 2) Red/Solid = Transient fault condition. Drive will resume operation when the condition causing the fault is removed. 3) Green/Double-linking = STO circuit active, drive outputs are Safe-Torque-Off 4) Green/Slow-linking = Drive OK but NOT-enabled. Will run when enabled. 5) Green/Fast-linking = Positive or Negative limit switch active. Drive will only move in direction not inhibited by limit switch. 7) Green/Solid = Drive OK and enabled. Will run in response to reference inputs or EtherCAT commands. Latching Faults Default Optional (programmable) Short circuit (Internal or external) Over-voltage Drive over-temperature Under-voltage Motor over-temperature Motor Phasing Error Feedback Error Following Error Command Input Lost Motor Wiring Disconnected STO Active Over Current (latched) AMP J8 P/N Rev 03 Page 4 of 30

5 canopen communications Xenus uses the CAN physical layer signals CAN_H, CAN_L, and CAN_GND for connection, and CANopen protocol for communication. efore installing the drive in a CAN system, it must be assigned a CAN address. A maximum of 27 CAN nodes are allowed on a single CAN bus. The rotary switch on the front panel controls the four lower bits of the seven-bit CAN address. When the number of nodes on a bus is less than sixteen, the CAN address can be set using only the switch. Address 0 is reserved for the CAN bus master. For installations with sixteen or more CAN nodes on a network CME 2 can be used to configure Xenus to use the rotary switch, or combinations of digital inputs and programmed offset in flash memory to configure the drive with a higher CAN node address. For more information on CANopen communications, download the CANopen Manual from the Copley web-site: canopen connectors Dual RJ-45 connectors that accept standard Ethernet cables are provided for CAN bus connectivity. Pins are wired-through so that drives can be daisychained and controlled with a single connection to the user s CAN interface. A CAN terminator should be placed in the last drive in the chain. The XP2-NK connector kit provides a D-Sub adapter that plugs into a CAN controller and has an RJ-45 socket that accepts the Ethernet cable. Pin Pin 8 J7 XP2-NK can connector kit The kit contains the XP2-CV adapter that converts the CAN interface D-Sub 9M connector to an RJ-45 Ethernet cable socket, plus a 0 ft (3 m) cable and terminator. oth connector pin-outs conform to the CiA DR-303- specification D-Sub 9F CAN_L CAN_GND CAN_H CAN status LED CAN_L CAN_GND CAN_H 8 RJ-45 CAN Status LED J7 J7 CAN connections NET (CAN status) LED A bi-color LED gives the state of the CAN connection in accordance with the CAN-CiA specification 303, part 3. The green (RUN) LED shows the state of the CANopen state machine. The red (ERR) LED shows the occurrence of errors (sync, guard, or heartbeat) and of the CAN bus physical layer. During a reset condition, the green LED will be off. In operation, the red & green colors will alternate with the number of blinks or on/off condition shown in the table to the right. Note: Red & green led on-times do not overlap. LED color may be red, green, off, or flashing of either color. Note: Red & green led on-times do not overlap. LED color may be red, green, off, or flashing of either color. can network node-id (address) In an CANopen network, nodes are assigned addresses ~27. Address 0 is reserved for the CAN bus master. In the, the node address is provided by two 6-position rotary switches with hexadecimal encoding. These can set the address of the drive from 0x0~0x7F (~27 decimal). The chart shows the decimal values of the hex settings of each switch. DEVICE ID X0 X S S2 CANopen Settings CME2 -> Amplifier -> Network Configuration Node-ID (Address) Switches To find the Node-ID given the switch settings: Node-ID = (S * 6) S2 Example: S = 5, S2 = S value = (5*6) = 80, S2 value = Hex() =, Node-ID = 80 = 9 To find the switch settings for a given address: S = The integer part of (Node-ID / 6) S2 = Hex (Node-ID - (S * 6) ) Example: Node-ID = 9 S = 9/6 = 5.69, integer part = 5, (5*6) = 80 S2 = Hex (9-80) = = 0x S S2 Hex Dec A Not 0 Used C for CAN 2 D Addr 3 E 4 F 5 P/N Rev 03 Page 5 of 30

6 communications: rs-232 serial RS-232 communications is configured via a three-wire, full-duplex DTE RS-232 port that operates from 9600 to 5,200 aud, 8 bits, no parity, and one stop bit. format is full-duplex, 3-wire, DTE using RxD, TxD, and Gnd. Connections to the RS-232 port are through J8, an RJ- connector. The Serial Cable Kit (SER-CK) contains a modular cable, and an adapter that connects to a 9-pin, Sub-D serial port connector (COM, COM2, etc.) on PC s and compatibles. SER-CK serial cable kit The SER-CK provides connectivity between a D-Sub 9 male connector and the RJ- connector on the. It includes an adapter that plugs into the COM (or other) port of a PC and uses common modular cable to connect to the. The connections are shown in the diagram below D-Sub 9F RxD TxD Gnd Dsub-9F to RJ Adapter RJ- cable 6P6C Straight-wired TxD RxD Gnd 6 RJ- on Servo Drive J8: RS-232 Port RJ- receptacle, 6 position, 4 contact RxD RJ- (DTE) TxD Pin signal 2 RxD 3,4 Gnd 5 Txd Don t forget to order a Serial Cable Kit SER-CK when placing your order for an! ascii communication protocol ASCII communications The Copley ASCII Interface is a set of ASCII format commands that can be used to operate and monitor Copley Controls Accelnet, Stepnet, and Xenus series amplifiers over an RS-232 serial connection. For instance, after basic amplifier configuration values have been programmed using CME 2, a control program can use the ASCII Interface to: Enable the amplifier in Programmed Position mode. Home the axis. Issue a series of move commands while monitoring position, velocity, and other run-time variables. Additional information can be found in the ASCII Programmers Guide on the Copley website: RS-232 multi-drop The RS-232 specification makes no allowance for more than two devices on a serial link. ut, multiple drives can communicate over a single RS-232 port by daisy-chaining a master drive to other drives using CAN cables. In the CAN protocol, address 0 is reserved for the CAN master and thereafter all other nodes on a CAN network must have unique, non-zero addresses. When the CAN address is set to 0, it acts as a CAN master, converting the RS-232 data into CAN messages and passing it along to the other drives which act as CAN nodes. RS-232 CANopen CANopen CAN Addr 0 CAN Addr CAN Addr n CAN Master CAN Node CAN Node For Serial-multi-drop you ll need an Serial Cable Kit SER-CK plus CANopen network cables to connect the drives as shown. The XP2-NC-0 and XP2-NC-0 are ft (0.3m) and 0 ft (3m) cables that will do the job. P/N Rev 03 Page 6 of 30

7 safe torque off (sto) description The provides the Safe Torque Off (STO) function as defined in IEC Three opto-couplers are provided which, when de-energized, prevent the upper and lower devices in the PWM outputs from being operated by the digital control core. This provides a positive OFF capability that cannot be overridden by the control firmware, or associated hardware components. When the opto-couplers are activated (current is flowing in the input diodes), the control core will be able to control the on/off state of the PWM outputs. installation Refer to the Xenus Plus Compact STO Manual (6-0553) DANGER The information provided in the Xenus Plus Dual-Axis STO User Manual must be considered for any application using the drive STO feature. Failure to heed this warning can cause equipment damage, injury, or death. sto bypass (muting) In order for the PWM outputs of the drive to be activated, current must be flowing through all of the opto-couplers that are connected to the STO- and STO-2 terminals of J4, and the drive must be in an ENALED state. When the opto-couplers are OFF, the drive is in a Safe Torque Off (STO) state and the PWM outputs cannot be activated by the control core to drive a motor. This diagram shows connections that will energize all of the opto-couplers from an internal current-source. When this is done the STO feature is overridden and control of the output PWM stage is under control of the digital control core. If not using the STO feature, these connections must be made in order for the drive to be enabled. sto bypass connections ypass Plug Connections Jumper pins: 2-4, 3-5, 6-8, 7-9 * J4 Channel 3 FPGA PWM Enable Gate Drivers HV Current must flow through all of the opto-couplers before the drive can be enabled * STO bypass connections on the and Xenus XEL/XPL models are different. If both drives are installed in the same cabinet, the diode should be wired as shown to prevent damage that could occur if the STO bypass connectors are installed on the wrong drive. The diode is not required for STO bypass on the and can be replaced by a wire between pins 7 and 9. * Channel STO-IN STO-IN- Channel 2 STO-IN2 STO-IN2- STO-IN STO-IN- STO-ypass (6.5 ma) STO-Gnd (Sgnd) FPGA UVW PWM EN PWM Outputs Frame Ground STO connector SAFETY J4 signals Pin Pin Frame Gnd 6 STO-() 2 STO-() 7 STO-(-) 3 STO-(-) 8 STO-PWR 4 STO-2() 9 STO-Gnd 5 STO-2(-) P/N Rev 03 Page 7 of 30

8 digital command inputs: position position command inputs Digital position commands must be sourced from devices with active pullup and pull-down to take advantage of the high-speed inputs. For differential commands, the A & channels of the multi-mode encoder ports may be used. Single-ended pulse & Direction [IN5] Pulse [IN6] Direction differential pulse & Direction [IN3] PULSE [IN4] /PULSE single-ended: IN5, 6 J6 Pins [IN5] Pls, CU, Enc A [IN6] Dir, CD, Enc 2 [IN5] [IN6] DIRECTION /DIRECTION Ground 6,6,22,3, 37,44 Frame Ground Single-ended CU/CD [IN5] CU (CW) [IN6] CD (CCW) QUAD a/b ENCODER SINGLE-ENDED Enc. Ph. A [IN5] Enc. A [IN6] Enc. Enc. Ph. differential CU/CD CU (Count-Up) [IN3] [IN4] CD (Count-Down) [IN5] [IN6] CU (CW) /CU (CW) CD (CCW) /CD (CCW) QUAD a/b ENCODER DIFFERENTIAL Encoder ph. A Encoder ph. [IN3] [IN4] [IN5] [IN6] Enc. A /Enc. A Enc /Enc differential: IN3,4,5,6 J6 Pins [IN3] Pls, CU, Enc A 9 [IN4] /Pls, /CU, Enc /A 0 [IN5] Dir, CD, Enc [IN6] /Dir, /CD, Enc / 2 Ground 6,6,22,3, 37,44 Frame Ground digital command inputs: velocity, torque Single-ended digital torque or velocity commands must be sourced from devices with active pull-up and pull-down to take advantage of the highspeed inputs. Single-ended PWM & Direction [IN5] [IN6] Curr-Vel Pol-Dir differential PWM & Direction Duty = 0-00% For differential commands, the A & channels of the multi-mode encoder ports may be used. [IN3] [IN4] [IN5] [IN6] Curr-Vel /Curr-Vel Pol-Dir /Pol-Dir single-ended: IN5,6 J6 Pins [IN5] Curr-Vel± [IN6] Pol-Dir 2 Sgnd 6,6,22,3, 37,44 Frame Ground Single-ended 50% PWM differential 50% PWM differential: IN3,4,5,6 J6 Pins Duty = 50% ±50% <no connection> [IN5] [IN6] Curr-Vel± <not used> Duty = 50% ±50% [IN3] [IN4] Curr-Vel /Curr-Vel [IN3] Curr-Vel± 9 [IN4] / Curr-Vel± 0 [IN5] Pol-Dir [IN6] /Pol-Dir 2 <no connection> [IN5] [IN6] No Function Ground 6,6,22,3, 37,44 Frame Ground P/N Rev 03 Page 8 of 30

9 Multi-mode encoder port as an input input types POSITION COMMAND INPUTS: DIFFERENTIAL Pulse & Direction CW & CCW (Clockwise & Counter-Clockwise) Encoder Quad A & Camming Encoder A & input MAX3097 signals & pins J6 Pulse, CW, Encoder A 36 /Pulse, /CW, Encoder /A 2 Direction, CCW, Encoder 35 A//X signals from digital encoder MAX3032 Input/Output Select /Direction, /CCW, Encoder / 20 Quad Enc X, Absolute Clock 34 Quad Enc /X, /Absolute Clock 9 Enc S, Absolute (Clock) Data 33 CURRENT or VELOCITY COMMAND INPUTS: DIFFERENTIAL Current or Velocity & Direction Current or Velocity () & Current or Velocity (-) Enc /S, / Absolute (Clock) Data 8 Ground 6, 6, 22, 3, 37, 44 Frame Ground MAX3097 Pulse/Dir or CU/CD differential commands MAX3032 Input/Output Select J6 Control Frame Ground A /A Enc. A SECONDARY FEEDACK: INCREMENTAL Quad A//X incremental encoder / Incremental Encoder Enc. MAX3097 X A//X signals from digital encoder Input/Output Select /X Enc. X MAX3032 Enc. X SECONDARY FEEDACK: ASOLUTE S channel: Absolute A encoders (2-wire) The S channel first sends a Clock signal and then receives Data from the encoder in half-duplex mode. S & X channels: SSI, iss, EnDat encoders (4-wire) The X channel sends the Clock signal to the encoder, which initiates data transmission from the encoder on the S-channel in full-duplex mode S /S Enc. S Enc. S Enc. X Absolute Encoder MAX3362 S 2-Wire digital absolute encoder signals Input/Output Select MAX3362 S 4-Wire digital absolute encoder signals Input Select Output Select 500 ma Ground S X MAX3362 P/N Rev 03 Page 9 of 30

10 multi-mode port as an output output types buffered feedback outputs: DIFFERENTIAL Encoder Quad A,, X channels Direct hardware connection between quad A//X encoder feedback and differential line drivers for A//X outputs emulated feedback outputs: DIFFERENTIAL Firmware produces emulated quad A/ signals from feedback data from the following devices: Absolute encoders Analog Sin/Cos incremental encoders J6 Control Frame Ground A /A Enc. A Incremental Encoder signals & pins / Enc. J6 Encoder A 36 Encoder /A 2 Encoder 35 Encoder / 20 Encoder X 34 Encoder /X 9 Encoder S 33 Encoder /S 8 X /X Enc. X Ground 6, 6, 22, 3, 37, 44 Frame Ground Secondary Encoder Input Secondary Encoder Input MAX3097 MAX3097 uffered A//X signals from primary encoder Input/Output Select Emulated A/ signals Input/Output Select MAX3032 MAX3362 Quad A//X primary encoder Emulated Quad A/ signals from analog Sin/Cos encoder P/N Rev 03 Page 0 of 30

11 CME2 defaults These tables show the CME2 default settings. They are user-programmable and the settings can be saved to non-volatile flash memory. Name Configuration PU/PD IN Enable-LO, Clear Faults IN2 IN3 /Gnd IN4 IN5 IN6 IN7 Not Configured IN8 IN9 IN0 IN Opto Not Configured Motemp PU Name OUT OUT2 OUT3 OUT4 OUT5 Notes Isolated Not Configured HS Output Not Configured rake Active-HI Name Analog: Reference Filter Vloop: Input Filter Vloop: Output Filter Vloop: Output Filter 2 Vloop: Output Filter 3 Iloop: Input Filter Iloop: Input Filter 2 Input Shaping Notes Disabled Disabled Low Pass, utterworth, 2-pole, 200 Hz Disabled Disabled Disabled Disabled Disabled Active Notes Short Circuit Amp Over Temperature Motor Over Temp Over Voltage Under Voltage Feedback Error Motor Phasing Error Following Error Command Input Fault Motor Wiring Disconnected STO Active Optional Faults Over Current (Latched) Option Method Notes Set Current Position as Home P/N Rev 03 Page of 30

12 high speed inputs: in, IN2 Digital, non-isolated, high-speed Progammable pull-up/pull-down 24V Compatible Programmable functions specifications Input Data Notes HI VT = 2.5~3.5 Vdc LO VT- =.3~2.2 Vdc Input Voltages VH VH = ±0.7~.5 Vdc Max 30 Vdc Min 0 Vdc Pull-up/down R 5 kw Low pass filter R2 5 kw C 00 pf Input Current 24V.3 madc 0V madc Time constant RC 2.5 µs connections Input Pin IN J6-7 IN2 J6-8 Sgnd J6-6, 6, 22, 3, 37, 44 Notes: ) VH is hysteresis voltage (VT) - (VT-) 2) The R2*C2 time constant applies when input is driven by active HI/LO devices FEEDACK CONNECTOR R [IN,2] R2 C PullUp = PullDown = 0V 74HC2G4 single-ended/differential inputs: in3, in4, in5, in6 Digital, non-isolated, high-speed Progammable pull-up/pull-down 2V Compatible Single-ended or Differential Programmable functions single-ended 2V max J6 Control R R2 MAX3096 specifications Input Data Notes [IN3,5] C Input Voltages Single-ended Input Voltages Differential 3 HI LO VH HI LO VH Vin 2.7 Vdc Vin 2.3 Vdc 45 mvdc typ Vdiff 200 mvdc Vdiff -200 mvdc ±45 mvdc typ R [IN4,6] R2 C 2.5V MAX3096 Common mode Vcm 0 to 2 Vdc Pull-up/down R 0 kw differential Low pass filter R2 C kw 00 pf 2V max J6 Control Time constant RC 2 00 ns R R2 MAX3096 Notes: ) VH is hysteresis voltage IN2 - IN3 or IN2 - IN3 2) The R2*C2 time constant applies when input is driven by active HI/LO devices) 3) Vdiff = AINn() - AINn(-) n = for Axis A, 2 for Axis connections S.E. Diff Pin IN3 IN3 J6-9 IN4 IN4- J6-0 IN5 IN5 J6- IN6 IN6- J6-2 Sgnd J6-6, 6, 22, 3, 37, 44 [IN3,5] R [IN4,6] C R2 C P/N Rev 03 Page 2 of 30

13 opto-isolated inputs: in7, in8, IN9, IN0 Digital, opto-isolated A group of four, with a common terminal Works with current sourcing or sinking drivers 24V Compatible Programmable functions 24V GND 24V J6 [INCOM] specifications [IN7] 4.7k Input Data Notes 4.99k 4.7V HI Vin ±0.0 Vdc * Input Voltages LO Vin ±6 Vdc * Max ±30 Vdc * [IN8] 4.7k Input Current ±24V ±3.6 madc 0V 0 madc 4.99k 4.7V * Vdc Referenced to ICOM terminals. [IN9] 4.7k connections J6 Pin 4.99k 4.7V IN7 3 IN8 4 IN9 5 IN V [IN0] 4.7k 4.99k 4.7V ICOM 28 motor overtemp input: in Digital, non-isolated Motor overtemp input 24V Compatible Programmable functions motor over temp input The 4.99k pull-up resistor works with PTC (positive temperature coefficient) thermistors that conform to S 4999:Part :987, or switches that open/ close indicating a motor over-temperature condition. The active level is programmable. specifications Input Data Notes Input Voltages HI LO Max Vin 3.5 Vdc Vin 0.7 Vdc 24 Vdc [IN] R R2 Min 0 Vdc Pull-up R 4.99 kw Thermistor, Posistor, or switch Gnd C Input Current 24V 0V 5.7 madc -.0 madc Low pass filter R2 C 0 kw 33 nf Time constant Te 330 µs * * RC time constant applies when input is driven by active high/low device connections Input Pin IN -7 Sgnd -5, 6, 25, 26 S 4999:Part :987 Property Resistance in the temperature range 20 C to 70 C Resistance at 85 C Resistance at 95 C Resistance at 05 C ohms 60~ P/N Rev 03 Page 3 of 30

14 analog input: ain ±0 Vdc, differential 2-bit resolution Programmable functions As a reference input it takes position/velocity/torque commands from a controller. If not used as a command input, it can be used as generalpurpose analog input. specifications D/A J6 Spec Data Notes Input Voltage Vref ±0 Vdc Input Resistance Rin 5.05 kw connections Pins ±0V F.G. Shield (Frame Gnd) AIN() AIN(-) Sgnd -.5V Vref AIN() J6-3 AIN(-) J6-2 Sgnd J6-6, 6, 22, 3, 37, 44 opto-isolated outputs: out, out2, out3 Digital, opto-isolated MOSFET output SSR, 2-terminal Flyback diode for inductive loads 24V Compatible Programmable functions SSR [OUTn] J6 80Ω min* 300mA max specifications Output Data Notes ON Voltage OUT() - OUT(-) Vdc 300 madc Output Current Iout 300 madc max 36V [OUTn-] * at 24 Vdc Vdc connections () (-) OUT J6-42 J6-27 OUT2 J6-4 J6-26 OUT3 J6-40 J6-25 HI/LO definitions: outputs Input State Condition HI Output SSR is ON, current flows OUT~3 LO Output SSR is OFF, no current flows P/N Rev 03 Page 4 of 30

15 high-speed output: out4 CMOS buffer 74AHCTG25 Programmable functions 5 Vdc J6 specifications [OUT4] ±8 ma Output HI Data Notes Vout HI Voh 4.4 Vdc Iout HI Ioh -8.0 madc Vout LO Vol 0.40 Vdc Iout LO Iol 8.0 madc Sgnd R opto-isolated motor brake output: out5 rake output Opto-isolated Flyback diode for inductive load 24V Compatible Connection for external 24V power supply Programmable functions specifications J3 4 3 rk 24V Input rk 24V Output Output Data Notes Voltage Range Max 30 Vdc Output Current Ids.0 Adc HI/LO definitions: outputs Input State Condition RAKE [OUT5] HI LO Output transistor is OFF rake is un-powered and locks motor Motor cannot move rake state is Active Output transistor is ON rake is powered, releasing motor Motor is free to move rake state is NOT-Active CME2 Default Setting for rake Output [OUT5] is rake - Active HI Active = rake is holding motor shaft (i.e. the rake is Active) Motor cannot move No current flows in coil of brake CME2 I/O Line States shows Output 4 as HI RK Output voltage is HI (24V), MOSFET is OFF Servo drive output current is zero Servo drive is disabled, PWM outputs are off Inactive = rake is not holding motor shaft (i.e. the rake is Inactive) Motor can move Current flows in coil of brake CME2 I/O Line States shows Output 5 as LO RK output voltage is LO (~0V), MOSFET is ON Servo drive is enabled, PWM outputs are on Servo drive output current is flowing i J3 connections Pin 2 4 rk 24V Input 3 rk 24V Output 2 rake [OUT5] 24V Return rake [OUT5] 24V Return The brake circuits are optically isolated from all drive circuits and frame ground. 0 24V P/N Rev 03 Page 5 of 30

16 feedback connections quad a/b ENCODER with fault protection Encoders with differential line-driver outputs are required (single-ended encoders are not supported) and provide incremental position feedback via the A/ signals and the optional index signal (X) gives a once per revolution position mark. The MAX3097 receiver has differential inputs with fault protections for the following conditions: Short-circuits line-line: Open-circuit condition: Low differential voltage detection: ±5kV ESD protection: Extended common-mode range: This produces a near-zero voltage between A & /A which is below the differential fault threshold. The 2W terminator resistor will pull the inputs together if either side (or both) is open. This will produce the same fault condition as a short-circuit across the inputs. This is possible with very long cable runs and a fault will occur if the differential input voltage is < 200mV. The 3097E has protection against high-voltage discharges using the Human ody Model. A fault occurs if the input common-mode voltage is outside of the range of -0V to 3.2V quad encoder with index quad encoder with no index Encoder A//X s Encoder FG A Frame Ground A 2 /A Enc. A Pins Enc A 3 Enc /A 2 Enc FG A Frame Ground A 2 /A Enc. A Enc / 0 X 0V 2 / X k 30 /X k 500 ma Ground Enc. Enc. Index Enc X 9 Enc /X 8 6, 7 Sgnd 5, 6, 25, 26 F.G. Sgnd = Ground F.G. = Frame Gnd 2 / X 2 /X 500 ma Enc. Enc. Index 0V Ground ANALOG sin/cos incremental ENCODER The sin/cos inputs are analog differential with 2 Ω terminating resistors and accept Vp-p signals in the format used by incremental encoders with analog outputs, or with ServoTube motors. The index input is digital, differential. RESOLVER (-R models) Connections to the resolver should be made with shielded cable that uses three twisted-pairs. Once connected, resolver set up, motor phasing, and other commissioning adjustments are made with CME 2 software. There are no hardware adjustments. Encoder Resolver resolver s FG sin cos indx 0V Frame Ground Sin() 0k - 2 Sin Sin(-) 0k 0k Cos() - 2 Cos Cos(-) 0k X k 30 Enc. Index /X k 500 ma Ground sin/cos s Pins Sin() 9 Sin(-) 8 Cos() 2 Cos(-) 20 X 9 /X 8 6, 7 Sgnd 5, 6, 25, 26 F.G. S3 R2 Sin Ref FG S S2 Cos S4 R Frame Ground Sin() Sin(-) R/D Conversion Cos() Cos(-) Ref() Ref(-) Pins S3 9 S 8 S2 2 S4 20 R 23 R2 22 Sgnd 5, 6, 25, 26 F.G. Sgnd = Ground F.G. = Frame Gnd Sgnd P/N Rev 03 Page 6 of 30

17 feedback connections Ssi absolute Encoder The SSI (Synchronous Serial Interface) is an interface used to connect an absolute position encoder to a motion controller or control system. The drive provides a train of clock signals in differential format to the encoder which initiates the transmission of the position data on the subsequent clock pulses. The polling of the encoder data occurs at the current loop frequency (6 khz). The number of encoder data bits and counts per motor revolution are programmable. The hardware bus consists of two signals: SCLK and SDATA. Data is sent in 8 bit bytes, LS first. The SCLK signal is only active during transfers. Data is clocked out on the falling edge and clock in on the rising edge of the Master. Encoder Clk Data FG Frame Ground Clk /Clk Dat /Dat 30 k 22 k k k A A Clk Data SSI,iSS s SSI iss Pins Clk MA 9 /Clk MA- 8 Data SL 5 /Data SL- 4 6, 7 Ground 5, 6, 25, 26 Frame Gnd iss absolute Encoder iss is an - Open Source - digital interface for sensors and actuators. iss refers to principles of well known industrial standards for Serial Synchronous Interfaces like SSI, AS-Interface and Interbus with additional options. Serial Synchronous Data Communication Cyclic at high speed 2 unidirectional lines Clock and Data Line delay compensation for high speed data transfer Request for data generation at slaves Safety capable: CRC, Errors, Warnings us capability incl. actuators idirectional iss -protocol: Mode choice at each cycle start iss C-protocol: Continuous mode iss Encoder FG Master Slave Frame Ground MA SL k k 30 k 22 Clk Data 0V 500 ma Ground Note: Single (outer) shields should be connected at both ends (motor and drive frame grounds). Inner shields should only be connected to Ground on the drive. V V- k 500 ma Ground endat absolute Encoder The EnDat interface is a Heidenhain interface that is similar to SSI in the use of clock and data signals, but which also supports analog sin/ cos channels from the same encoder. The number of position data bits is programmable as is the use of sin/cos channels. Use of sin/cos incremental signals is optional in the EnDat specification. Encoder Clk Data sin cos FG 0V Frame Ground Clk /Clk Dat /Dat k k k A 22 A k Sin() 0k - 2 Sin Sin(-) 0k Cos() Cos(-) 30 0k 2 0k 500 ma Ground - Clk Data Cos endat s Pins Clk 9 /Clk 8 Data 5 /Data 4 Sin() 9 Sin(-) 8 Cos() 2 Cos(-) 20 6, 7 Sgnd 5, 6, 25, 26 F.G. Sgnd = Ground F.G. = Frame Gnd Absolute-a Encoder The Absolute A interface is a serial, half-duplex type that is electrically the same as RS-485. Note the battery which must be connected. Without it, the encoder will produce a fault condition. SD D-R Cmd MAX3362 Absolute-A Encoder 5V.2k SD.2k att MA- SL- 220 SD- att- V V- 0V attery Absolute A Tamagawa Absolute A Panasonic Absolute A Format Sanyo Denki Absolute A - Dat /Dat 5V k 22 k 500 ma Ground Pins Data 5 /Data 4 6, 7 Sgnd 5, 6, 25, 26 F.G. Cmd D-R SD absolute-a s Sgnd = Ground F.G. = Frame Gnd P/N Rev 03 Page 7 of 30

18 motor connections motor phase connections The drive output is a three-phase PWM inverter that converts the DC buss voltage (HV) into three sinusoidal voltage waveforms that drive the motor phase-coils. Cable should be sized for the continuous current rating of the motor. Motor cabling should use twisted, shielded conductors for CE compliance, and to minimize PWM noise coupling into other circuits. The motor cable shield should connect to motor frame and the drive frame ground terminal (J2-) for best results. motor s J2 Pin Mot U 4 Mot V 3 Mot W 2 Frame Gnd HV 0V PWM F.G. W V U J2 Motor 3 ph. digital HALL SIGNALS Hall signals are single-ended signals that provide absolute feedback within one electrical cycle of the motor. There are three of them (U, V, & W) and they may be sourced by magnetic sensors in the motor, or by encoders that have Hall tracks as part of the encoder disc. They typically operate at much lower frequencies than the motor encoder signals, and are used for commutation-initialization after startup, and for checking the motor phasing after the amplifier has switched to sinusoidal commutation. hall s Pins Hall U 2 Hall V 3 Hall W 4 6, 7 Sgnd 5, 6, 25, 26 Frame Gnd Halls Hall A Hall Hall U Hall V 0K 0K 00p 0K 0K 00p Hall C Hall W 0K 0K 00p 500 ma 0V Ground P/N Rev 03 Page 8 of 30

19 motor connections: digital quad a/b encoders The connections shown may not be used in all installations Xenus Plus Compact Frame Gnd 6 Out Gnd A /A / X /X Hall U 2 Hall V 3 Hall W 4 A /A / X /X Vcc 0V DIGITAL ENCODER DIGITAL HALLS Gnd 6 Motemp 7 TEMP SENSOR rk 24V Input 4 J3 rk 24V Output rake 3 2 rk 24 Vdc 0V 24V Return J2 Mot U Mot V Mot W U V W RUSHLESS MOTOR U() V(-) RUSH MOTOR Frame Gnd Notes: ) CE symbols indicate connections required for CE compliance. 2) When STO feature is used, the 24V power supply must be SELV or PELV with output voltage limited to 60 Vdc. P/N Rev 03 Page 9 of 30

20 motor connections: analog sin/cos incremental encoders The connections shown may not be used in all installations Xenus Plus Compact Frame Gnd Enc Sin() Enc Sin(-) Enc Cos() Enc Cos(-) Enc Index() Enc Index(-) 6 Out Gnd Hall U 2 Hall V 3 Hall W 4 Sin Sin- Cos Cos- Ndx Ndx- Vcc 0V ANALOG SIN/COS ENCODER DIGITAL INDEX DIGITAL HALLS Gnd 6 Motemp 7 TEMP SENSOR rk 24V Input 4 J3 rk 24V Output rake 3 2 rk 24 Vdc 0V 24V Return J2 Mot U Mot V Mot W U V W RUSHLESS MOTOR U() V(-) RUSH MOTOR Frame Gnd Notes: ) CE symbols indicate connections required for CE compliance. 2) When STO feature is used, the 24V power supply must be SELV or PELV with output voltage limited to 60 Vdc. P/N Rev 03 Page 20 of 30

21 motor connections: resolvers (-r option) Xenus Plus Compact Frame Gnd Rslvr Sin() Rslvr Sin(-) Rslvr Cos() Rslvr Cos(-) Rslvr Ref() Rslvr Ref(-) S3 S S2 S4 R R2 RESOLVER 6 Out 7 Gnd Hall U 2 Hall V 3 Hall W 4 Gnd 6 Motemp 7 TEMP SENSOR rk 24V Input 4 J3 rk 24V Output rake 3 2 rk 24 Vdc 0V 24V Return J2 Mot U Mot V Mot W U V W RUSHLESS MOTOR U() V(-) RUSH MOTOR Frame Gnd Notes: ) CE symbols indicate connections required for CE compliance. 2) When STO feature is used, the 24V power supply must be SELV or PELV with output voltage limited to 60 Vdc. P/N Rev 03 Page 2 of 30

22 CONNECTORS & SIGNALS WARNING: Hazardous voltages exist on connections to J, & J2 when power is applied, and for up to 4 minutes after power is removed. ISOLATED CIRCUIT J Mains Connections Pin Mains Input L3 5 Frame Ground 4 PE Ground 3 Mains Input L2 2 Mains Input L J2 Motor Output Pin Motor Phase U 4 Motor Phase V 3 Motor Phase W 2 Frame Ground J POWER J2 MOTOR 5 min L L2 L3 W V U J3 24 VDC & rake Pin 24V Input 4 24V to rakes 3 rake 2 24V Return J3 RAKE J4 24V RTN RK J7 J4 SAFETY (STO) Pin Pin Frame Gnd 6 STO-IN() 2 STO-IN() 7 STO-IN(-) 3 STO-IN(-) 8 STO-Mute 4 STO-IN2() 9 STO-Gnd 5 STO-IN(-) SAFETY Xenus Plus J8 P/N Rev 03 Page 22 of 30

23 CONNECTORS & SIGNALS Feedback Pin Pin Pin N RUN L/A NETWORK J6 x0 x DEVICE ID L/A FEEDACK CONTROL S S2 OUT IN Frame Gnd 0 Enc / 9 Sin() S3 2 Hall U Enc 20 Cos(-) S4 3 Hall V 2 Enc /A 2 Cos() S2 4 Hall W 3 Enc A 22 n/c 5 Gnd 4 Enc /S 23 n/c 6 Out 5 Enc S 24 n/c 7 Motemp IN 6 Gnd 25 Gnd 8 Enc /X 7 Out 26 Gnd 9 Enc X 8 Sin(-) S Notes: ) The total current drawn from Out on cannot exceed 500 ma. 2) The total current drawn from Out2 on J6 cannot exceed 500 ma. J6 control & i/o Pin Pin Pin Frame Gnd 6 Gnd 3 Gnd 2 Ref(-) 7 Out2 32 Out2 3 Ref() 8 Multi Enc /S 33 Multi Enc S 4 n/c 9 Multi Enc /X 34 Multi Enc X 5 n/c 20 Multi Enc / 35 Multi Enc 6 Gnd 2 Multi Enc /A 36 Multi Enc A 7 [IN] GP 22 Gnd 37 Gnd 8 [IN2] GP 23 [OUT4] HS 38 n/c 9 [IN3] HS 24 n/c 39 n/c 0 [IN4] HS 25 [OUT3-] ISO 40 [OUT3] ISO [IN5] HS 26 [OUT2-] ISO 4 [OUT2] ISO 2 [IN6] HS 27 [OUT-] ISO 42 [OUT] ISO 3 [IN7] ISO 28 [INCOM] ISO 43 n/c 4 [IN8] ISO 29 n.c. 44 Sgnd 5 [IN9] ISO 30 [IN0] ISO ERR J8 RS-232 PORT A AMP RS-232 Pin signal n.c. 2 RxD 3 Gnd 4 Gnd 5 TxD RJ- receptacle, 6 position, 4 contact J8 Cable Connector: RJ- style, male, 6 position Cable: 6-conductor modular type, straight-through J8 RS-232 note. J8 signals are referenced to Gnd. 5 n.c. P/N Rev 03 Page 23 of 30

24 wiring AC power, and Motor output: J, J2 Wago MCS-MIDI Classic: /07-000, 5-pole (J), /07-000, 4-pole(J2), female connectors; with screw flange; pin spacing 5.08 mm / 0.2 in Conductor capacity are stranded: AWG 28~4 [0.08~2.5 mm2] Insulated ferrule: AWG 24~6 [0.25~.5 mm2] Stripping length: 8~9 mm Operating Tool: Wago MCS-MIDI Classic: J J2 Tool ferrule part numbers: single wire insulated AWG mm 2 Color Mfgr PNUM A C D E SL lue Wago (0.59) 8.0 (0.3) 2.05 (.08) 4.2 (0.7) 4.8 (0.9) 0 (0.39) 6.5 lack Wago ( (0.3).7 (.07) 3.5 (0.4) 4.0 (0.6) 0 (0.39) 8.0 Red Wago (.47) 6.0 (.24).4 (.055) 3.0 (.2) 3.5 (.4) 8 (.3) Gray Wago (.47) 6.0 (.24).2 (.047) 2.8 (.) 3.3 (.3) 8 (.3) White Wago (.47) 6.0 (.24).0 (.039) 2.6 (.0) 3. (.2) 7.5 (.30) notes PNUM = Part Number SL = Stripping length Dimensions: mm (in) C D E A 24V & brake: J3 Wago MCS-MINI: /07-000, female connector; with screw flange, 4-pole; pin spacing 3.5 mm / 0.38 in Conductor capacity are stranded: AWG 28~6 [0.08~.5 mm2] Insulated ferrule: AWG 24~6 [0.25~.5 mm2] Stripping length: 0.24~0.28 in[6~7 mm] Operating tool: Wago MCS-MINI: J3 Tool ferrule part numbers: single wire insulated AWG mm 2 Color Mfgr PNUM A C D E SL 8.0 Red Wago (.47) 6.0 (.24).4 (.06) 3.0 (.2) 3.5 (.4) 8 (.3) Gray Wago (.47) 6.0 (.24).2 (.05) 2.8 (.) 3.3 (.3) 8 (.3) White Wago (.47) 6.0 (.24).0 (.04) 2.6 (.0) 3. (.2) 7.5 (.30) ferrule part numbers: double wire insulated AWG mm 2 Color Mfgr PNUM A C D E SL 2 x 8 2 x.0 Red Altech (.6) 8.2 [.32] 2.4 (.09) 3.2 (.3) 5.8 (.23).0 (.43) 2 x 8 2 x.0 Gray Altech (.57) 8.2 (.32) 2.0 (.08) 3.0 (.2) 5.5 (.22).0 (.43) 2 x 20 2 x 0.75 White Altech (.57) 8.2 (.32).7 (.07) 3.0 (.2) 5.0 (.20).0 (.43) 2 x 20 2 x 0.75 Gray TE (.59) 8.0 (.3).70 (.07) 2.8 (.) 5.0 (.20) 0 (.39) 2 x 22 2 x 0.50 White TE (.59) 8.0 (.3).40 (.06) 2.5 (.0) 4.7 (.9) 0 (.39) SINGLE WIRE DOULE WIRE E C D E C D A A P/N Rev 03 Page 24 of 30

25 device structure & isolation Drive POWER SOURCES There are four isolation zones in the :. 24V, rake, & STO 2. Control circuits, RS-232 & CAN comms 3. High-voltage, regen, & PWM outputs 4. CANopen communicaions Each of these is isolated from the others and all are isolated from the chassis. 24 Vdc, brake, & sto The primary side of the DC/DC converter operates directly from the external 24 Vdc supply and is isolated from other drive power sections. Secondary windings provide power for each isolation zone. The rake output [OUT6] operates in this section and is referenced to the 24 Vdc return (0V). It sinks current from an external load connected to the external 24 Vdc power source. The STO circuits also operate from the 24V power and the STO-24V supplies current for de-activating (muting) the STO function when it is not used. SIGNAL and RS-232 circuits The signal power section supplies power for the control circuits as well as the RS-232 communications. Motor feedback signals such as Halls, encoder, and temperature sensor operate in this section. All signal circuits are referenced to Ground. This ground should connect to the control system circuit ground or common so that drive and controller inputs and output voltage levels work properly with each other. high voltage, regen, & pwm Mains power drives the high-voltage section. It is rectified and capacitor-filtered to produce internal DC bus which the PWM stage converts into voltages that drive either three phase brushless or DC brush motors. An internal solid-state switch and power resistor provides dissipation during regeneration. All the circuits in this section are hot, that is, they connect directly to the mains and must be considered high-voltages and a shock hazard requiring proper insulation techniques during installation. CAN Network The network connections in the CAN network receptacle are optically isolated from the other drive circuits. GROUNDING A grounding system has three primary functions: safety, voltage-reference, and shielding. As a safety measure, the PE (Protective Earth) ground at J-3 will carry fault-currents from the mains in the case of an internal failure or short-circuit of electronic components. Wiring to this is typically done with the green conductor with yellow stripe using the same gauge wire as that used for the mains. This wire is a bonding conductor that should connect to an earthed ground point and must not pass through any circuit interrupting devices. All of the circuits on J, and J2 are mainsconnected and must never be grounded. The frame ground terminals at J-3, J-4, J2, J4-, -, and J6- all connect to the drive chassis and are isolated from all drive internal circuits. grounding references the drive control circuits to those of the control system. These controls circuits typically have their own earth connection at some point. To eliminate ground-loops it is recommended that the drive signal ground be connected to the control system circuit ground. When this is done the drive signal voltages will be referenced to the same 0 V level as the circuits in the control system. Small currents flow between controller and drive when inputs and outputs interact. The signal ground is the path for these currents to return to their power sources in both controller and drive. Shields on cables reduce emissions from the drive for CE compliance and protect internal circuits from interference due to external sources of electrical noise. ecause of their smaller wire gauge, these should not be used as part of a safety-ground system. Motor cases can be safety-grounded either at the motor, by earthing the frame, or by a grounding conductor in the motor cable that connects to J2-. This cable should be of the same gauge as the other motor phase cables. J MAINS PE GROUND L L2 L3 ~ ~ ~ - Cable shield grounding socket 940 µf 3 Regen DC US() DC US(-) PWM INVERTER U V W J2 MOTOR CASE REGENERATION The chart below shows the energy absorption in W s for a drive operating at some typical mains voltages. When the load mechanical energy is greater than these values an external regen resistor is available as an accessory. J6 FEEDACK ENCODER, HALLS, RESOLVER CONTROL SYSTEM J8 RS-232 CONTROL SIGNAL GROUND RS-232 Interface 5 Vdc FEEDACK POWER & DECODING ENALE [IN] SIGNAL GND 2 CONTROL CORE J3 DC/DC CONVERTER J4 STO CONTROL 4 CAN XCVR 24V RAKE RAKE 24V Return STO_24V STO_GND NETWORK J7 CANopen Network 24V POWER P/N Rev 03 Page 25 of 30