Signals and Systems Lecture 6: Fourier Applications
|
|
- Valerie Garrett
- 5 years ago
- Views:
Transcription
1 Signals and Systems Lecture 6: Fourier Applications Farzaneh Abdollahi Department of Electrical Engineering Amirkabir University of Technology Winter 2012 arzaneh Abdollahi Signal and Systems Lecture 6 1/57
2 Filtering Frequency Shaping Filters Frequency Selective Filters Lowpass Filters Highpass Filters Bandpass Filters Ideal Filters Non-ideal Filters DT Filters Magnitude and Phase of Fourier Transform Magnitude-Phase Representation for Freq. response of LTI system Log Magnitude and Bode plots Sampling Sampling Effect in Freq. Farzaneh Abdollahi Signal and Systems Lecture 6 2/57
3 Filtering Filtering: is a process to Change the relative frequency components Eliminate some frequency components The filters can be Frequency shape filter: changes the shape of spectrum Frequency selective filter: passes some frequencies and significantly attenuate or eliminate others For LTI systems, we have: Y (jω) = H(jω)X (jω) Therefore for LTI systems filtering is defining proper frequency response H(jω) arzaneh Abdollahi Signal and Systems Lecture 6 3/57
4 Frequency Shaping Filters Example: In audio systems such filters allow the listener to change the relative amount of low frequency energy (bass) and high frequency energy (treble). Example: a differentiator: y(t) = dx dt Y (jω) = jωx (jω) H(jω) = jω The larger ω the more amplification will receive In control engineering such filter are employed for improving transient response or changing rapid variations (Proportional Differentiators (PD)) arzaneh Abdollahi Signal and Systems Lecture 6 4/57
5 Example Cont d Another application of differentiator filters is to enhance edges in picture processing A black-wight picture has a two dimensional signal in x and y directions It requires a two dimensional Fourier series Abrupt changes of brightness across edges leads to more concentration at higher frequency Passing the signal from differentiator enhance this concentration and make it more clear arzaneh Abdollahi Signal and Systems Lecture 6 5/57
6 Frequency Selective Filters This filters keep some band of frequencies and eliminate others. Example: If there is a noise in an audio recording in high frequency band, it can be removed by such filters Example: In Amplitude Modulation (AM), information is transmitted from different sources simultaneously s.t. each channel puts its information in separate frequency band. At receiver (in home radio/tv) Frequency Selective Filters separate the individual channels Frequency Shaping Filters (like equalizer) adjust the quality of tone Based on the bound that the Frequency Selective Filters pass, these filters can be categorized to Lowpass filters Highpass filters Bandpass filters arzaneh Abdollahi Signal and Systems Lecture 6 6/57
7 Lowpass Filters They passes the lower freqs. ( freq. around ω = 0) and attenuate or reject higher freqs. In CT In DT (Low freq. is at ω = 2kπ, k = 0, ±1, ±2,...) arzaneh Abdollahi Signal and Systems Lecture 6 7/57
8 Highpass Filters They passes the high freqs. and attenuate or reject low freqs. In CT In DT (the highest freq. at DT is at ω = (k + 1)π, k = 0, ±1, ±2,... since e jπn = ( 1) n ) arzaneh Abdollahi Signal and Systems Lecture 6 8/57
9 Bandpass Filters They passes a band of freqs. and attenuate or reject low and high freqs. In CT In DT arzaneh Abdollahi Signal and Systems Lecture 6 9/57
10 Pass Band : The band of freq. that is passed through filter Stop Band: The band of freq that is rejected by filter Cutoff Freq.: The border between pass band and stop band arzaneh Abdollahi Signal and Systems Lecture 6 10/57
11 Ideal Filters An ideal filter completely eliminates all signals info at stop band while passing those in pass band unchanged: An ideal lowpass filter: In pass band : H(jω) = 1, H(jω) = 0 In stop band H(jω) = 0 It is symmetric around ω = 0 An ideal low-pass filter can be realized mathematically by multiplying a signal by the rectangular function in the frequency domain { 1 ω ωc H(jω) = 0 ω > ω c or, convolution with sinc function (its impulse response), in the time domain Ideal filters are good for system analysis But they are not realizable and implementable in practice arzaneh Abdollahi Signal and Systems Lecture 6 11/57
12 Ideal Filter, Example: Consider an ideal low pass filter: CT { filter:h(jω) = 1 ω ωc h(t) = sinωct 0 ω > ω πt c DT filter: { 1 ω H(e jω ωc ) = 0 ω c < ω π h[n] = sinωcn πn Farzaneh Abdollahi Signal and Systems Lecture 6 12/57
13 Ideal Filter, Example: Farzaneh Abdollahi Signal and Systems Lecture 6 13/57
14 Example Cont d Lowpass filter is not casual (h(t)/h[n] is not zero for t < 0/n < 0) Therefore it is not implementable in real Moreover in some applications like suspension system oscillating behavior of impulse response of the filter is not desirable. In freq. the width of pass band is proportional to ω c ; in time, the width of the main lobe is proportional to 1 ω c To expand pass band in freq. impulse response of the filter should be narrower Now let us study the step response of these filters Reconsider s(t) = t h(τ)dτ/s[n] = n h[m] The step responses have overshoot comparing to the final value and they have oscillating response, none of them are desirable arzaneh Abdollahi Signal and Systems Lecture 6 14/57
15 Ideal Filter, Example: Farzaneh Abdollahi Signal and Systems Lecture 6 15/57
16 Phase shifting in Ideal Filters An ideal filter with linear phase (in pass band) results in a simple time shifting the filter in time domain. arzaneh Abdollahi Signal and Systems Lecture 6 16/57
17 Non Ideal Filters As we said the the ideal filters cannot be made in practice Moreover sometimes the sharp ending bandpass is not always desirable. For example, if the signals to be separated do not lie in totally disjoint frequency bands. A typical situation to separating them is a gradual transition from passband to stopband. The transition between passband and stop band is named transition band arzaneh Abdollahi Signal and Systems Lecture 6 17/57
18 A non-ideal low pass filter has three parts: pass band, transition band, stop band Deviation from unity of ±δ 1 is allowed in the passband Deviation of δ 2 from zero is allowed in the stopband. passband ripple: The amount by which the frequency response differs from unity in the passband stopband ripple The amount by which it deviates from zero in the stopband ω p : passband edge; ω s : stopband edge. transition band frequency range from ω p to ω s Similar definitions are applicable for DT non-ideal filters Farzaneh Abdollahi Signal and Systems Lecture 6 18/57
19 Non-Ideal Filters To control the behavior of the filter in time domain, step respond of the filter in investigated. The most important and popular indices are: Rise time (t r ) the time for the signal to get to the final value for the first time Overshoot the maximum value minus the step value divided by the step value Settling time the time required for signal to reach and remain within a given error band (5% or 2%) of its final value. arzaneh Abdollahi Signal and Systems Lecture 6 19/57
20 Non-ideal Filters The ideal filters have great performance in freq. but not acceptable performance in time, they are not implementable. Non-ideal filters intend to compromise between freq. performance and time performance. A simple example of a non-ideal low pass filter: an RC circuit Input: Voltage source v s (t); Output: capacitor voltage V c (jω) = H L (jω)v s (jω) arzaneh Abdollahi Signal and Systems Lecture 6 20/57
21 A non-ideal low pass filter cont d RC dvc(t) dt + v c (t) = v s (t) V c (jω)(rcjω + 1) = V s (jω) H L (jω) = Vc(jω) V s(jω) = 1 1+RCjω Farzaneh Abdollahi Signal and Systems Lecture 6 21/57
22 A non-ideal low pass filter cont d h(t) = 1 RC e t RC u(t) step response: s(t) = [1 e t RC ]u(t) τ = RC To decrease the pass band in freq. RC in step response, it takes longer to get to the final value! arzaneh Abdollahi Signal and Systems Lecture 6 22/57
23 A non-ideal high pass filter The same RC circuit But Voltage source v s (t); Output: resistor voltage V R (jω) = H H (jω)v s (jω) v R = RC dv C dt H H(jω) = RCjω 1+jωRC = 1 H L(jω) arzaneh Abdollahi Signal and Systems Lecture 6 23/57
24 A non-ideal high pass filter cont d Magnitude and phase of freq. response It passes the signal which freq. ω 1 RC with min attenuation arzaneh Abdollahi Signal and Systems Lecture 6 24/57
25 A non-ideal high pass filter cont d Step response of the filter: s(t) = e t RC u(t) By RC It takes longer time for step response to reach to the final value Pass band of filter is extended (cut of freq. is transferred to the lower freq.) arzaneh Abdollahi Signal and Systems Lecture 6 25/57
26 Band Pass Filters Band pass filters can also be made by resistors, amplifiers, capacitors, and etc. Designing a filter with variable center freq. is more challenging One method is designing a filter with fixed freq. and then take advantage of sin amplitude modulation (product property) arzaneh Abdollahi Signal and Systems Lecture 6 26/57
27 Band Pass Filters Y (jω) = δ(ω ω c ) X (jω) = X (j(ω ω c )) F (jω) = δ(ω + ω c ) W (jω) = W (j(ω ω c )) Farzaneh Abdollahi Signal and Systems Lecture 6 27/57
28 Band Pass Filters Now if we keep only real part of f, i.e. use cosω c t instead of e jωct, we get It is equivalent to a bandpass filter with center ω c arzaneh Abdollahi Signal and Systems Lecture 6 28/57
29 DT Filters They are described by difference equations The two basic classes: With Recursive equations With Non-recursive equations Recursive DT filters Their length of impulse response is infinite (Infinite Impulse Response IIR). Example: y[n] ay[n 1] = x[n] H(e jω 1 ) = 1 ae jω h[n] = a n u[n], s[n] = 1 an+1 1 a By choosing 0 < a < 1, a low pass filter is obtained Farzaneh Abdollahi Signal and Systems Lecture 6 29/57
30 Recursive DT Filter Example Cont d By choosing 1 < a < 0, a high pass filter is obtained There is a trade off between fast step response in time domain and bandwidth of filter in freq. domain a pass band and faster response Exercise: What will happen if a > 1 is chosen? By increasing order of filter, sharper filter (from pass band to stop band) with faster response is obtained. arzaneh Abdollahi Signal and Systems Lecture 6 30/57
31 Nonrecursive DT Filters They have Finite Impulse Response (FIR) Their general form is: y[n] = M k= N b kx[n k] Example: M = N = 1, y[n] = 1 3 (x[n 1] + x[n] + x[n + 1]) It is a low pass filter H(e jω ) = 1 3 (ejω e j ω ) = 1 3 (1 + 2cosω) By increasing number of sentences, the obtained filter shape is closer to the deal filter Farzaneh Abdollahi Signal and Systems Lecture 6 31/57
32 Nonrecursive DT Filters Example: Consider FIR filter : y[n] = 1 Its Freq. Response will be H(e jω 1 ) = N+M+1 Figs show H(e jω ) for N = M = 16 and 32 x[n k] M N+M+1 k= N M k= N e jωk arzaneh Abdollahi Signal and Systems Lecture 6 32/57
33 Nonrecursive DT Filters Example: y[n] = x[n] x[n 1] 2 It is a high pass filter H(e jω ) = 1 2 [1 ejω ] = je jω/2 sinω/2 To have causal filter N should be negative arzaneh Abdollahi Signal and Systems Lecture 6 33/57
34 Non-Ideal Filters In designing a lowpass filter a trade of between pass band (freq. domain) and settling time (time domain) can be considered Example: The fig. in next page shows a 5th ordered Butterworth filter and a 5th ordered elliptic filter Transient band of elliptic filter is narrower (it is sharper) than Butterworth filter The elliptic filter has more oscillations in step response and its settling time is longer than butterworth filter arzaneh Abdollahi Signal and Systems Lecture 6 34/57
35 Non-Ideal Filters arzaneh Abdollahi Signal and Systems Lecture 6 35/57
36 Non-Ideal Filters To obtain sharper filter on can use cascade to identical filters H 1 (jω) = H 2 (jω) H(jω) = H 1 (jω)h 2 (jω) = H 2 1 (jω) arzaneh Abdollahi Signal and Systems Lecture 6 36/57
37 Magnitude and Phase of Fourier Transform Fourier Transform is complex in general, therefore it can be expressed in polar representation: X (jω) = X (jω) e X (jω) X (e jω ) = X (e jω ) e X (ejω ) Reconsider Parseval s relation: x(t) 2 dt = 1 2π x(jω) 2 dω X (jω) 2 is energy density spectrum of x(t) X (jω) conveys information about relative magnitudes of the complex exponential terms which build x(t) X (jω) convey information about relative phases of complex exponential terms which build x(t) (phase distortion) arzaneh Abdollahi Signal and Systems Lecture 6 37/57
38 Magnitude-Phase Representation for Freq. response of LTI system In general, changes in phase function of X (jω) make changes in time domain characteristics of signal x(t) The auditory system can tolerate phase changes relatively By mild phase distortion in individual sound, the speech is still understandable But severe phase distortion may lead to loose intelligibility Example: playing a taped record backward F{x( t)} = X ( jω) = X (jω) e j X (jω) (change is only in phase) arzaneh Abdollahi Signal and Systems Lecture 6 38/57
39 Example x(t) = sin(2πt + φ 1) + sin(4πt + φ 2 ) cos(6πt + φ 3) φ1=φ2=φ3= t φ1=4, φ2=12, φ3= t φ1= 4, φ2=5, φ3= t arzaneh Abdollahi Signal and Systems Lecture 6 39/57
40 Magnitude-Phase Representation for Freq. response of LTI system In LTI systems we had: Y (jω) = H(jω)X (jω)/y (e jω ) = H(e jω )X (e jω ) One can express them in magnitude and phase: Y (jω) = H(jω) X (jω) Y (jω) = H(jω) + X (jω) (similar relation for DT) The effect of an LTI system on input signal is scaling its magnitude by H(jω) ( H(jω) is gain of the system) adding H(jω) to its phase ( H(jω) is phase shift of the system) By designing H(jω) properly one can modify the phase and magnitude of input signals (idea of designing controller ) arzaneh Abdollahi Signal and Systems Lecture 6 40/57
41 Group Delay Consider an LTI system with freq. response: H(jω) = e jωt 0 H(jω) = 1, and H(jω) = ωt 0 It makes a time shifting or delay: y(t) = x(t t 0 ) A delay in time has negative slop of phase at freq. arzaneh Abdollahi Signal and Systems Lecture 6 41/57
42 Log Magnitude and Bode plots To be able to express the magnitude relation of an LTI system by additive terms (similar to phase)logarithmic amplitude can be used: log Y (jω) = log H(jω) + log X (jω) Logarithmic scale provides this opportunity to display the details in wider dynamic range By logarithmic representation cascade of two LTI systems can be expressed as: log H(jω) = log H 1 (jω) + log H 2 (jω) H(jω) = H1 (jω) + H 2 (jω) Since H(jω) = H( jω) and H(jω) = H( jω): For CT log representation is found for ω > 0 For DT log representation is found for 0 < ω < π arzaneh Abdollahi Signal and Systems Lecture 6 42/57
43 FLog Magnitude and Bode plots Unit of logarithm amplitude scale is 20log 10 referred to 1 decibels (1 db). The name is in honor of Graham Bell It is defined based on the power ration of system (10log 10 H(jω) 2 ) Therefore: H(jω) = 1 0dB H(jω) = 2 3dB H(jω) = 2 6dB H(jω) = 10 20dB H(jω) = dB In CT, the freq is also represented by log scale Bode plots: Plots of 20log 10 H(jω) and H(jω) versus log 10 ω In DT since the freq. axis is always between ω = 0 and ω = π freq. does not required log scale. In some cases like ideal filters which amplitude is none zero only in a limited range of freq. linear scale is more suitable. arzaneh Abdollahi Signal and Systems Lecture 6 43/57
44 Sampling Due to significant development of digital technology, DT processors are more flexible comparing to CT ones. We are looking to define a method to transfer CT signals to DT. A method is sampling from CT signals If we take samples with unified distance from a CT signal, can we always retrieve it uniquely? arzaneh Abdollahi Signal and Systems Lecture 6 44/57
45 Sampling Let us use impulse train to take samples from x(t) in identical distance. p(t) = n= δ(t nt ) P(jω) = 2π T δ(ω kω s) (ω s = 2π T : sampling freq.) X p (jω) = 1 2π [X (jω) P(jω)] Farzaneh Abdollahi Signal and Systems Lecture 6 45/57
46 Sampling Effect in Freq. X p (jω) = 1 T k= X (j(ω kω s)) Assume ω M < ω s ω M ω s > 2ω M there is no overlap between the shifted replicas of X (ω) Farzaneh Abdollahi Signal and Systems Lecture 6 46/57
47 Sampling Effect in Freq. If ω s < 2ω M if ω s > 2ω M, x(t) can be exactly recovered from x p (t) by employing a lowpass filter with gain T and a cutoff freq. ω M < ω c < ω s ω m Farzaneh Abdollahi Signal and Systems Lecture 6 47/57
48 Sampling Theorem Let x(t) be a band limited signal with X (jω) = 0 for ω > ω M Then x(t) is uniquely determined by its samples x(nt ), n = 0, ±1, ±2,... if ω s > 2ω M where ω s = 2π T Given these samples, we can reconstruct x(t) by generating a periodic impulse train in which successive impulses have amplitudes that are successive sample values. This impulse train is then processed through an ideal lowpass filter with gain T and cutoff frequency ω M < ω c < ω s ω m. The resulting output signal will exactly equal x(t). ω s is Nyquist freq. ω M is Nyquist rate arzaneh Abdollahi Signal and Systems Lecture 6 48/57
49 Zero order Hold (ZOH) arzaneh Abdollahi Signal and Systems Lecture 6 49/57
50 Zero order Hold (ZOH) arzaneh Abdollahi Signal and Systems Lecture 6 50/57
51 Zero order Hold (ZOH) arzaneh Abdollahi Signal and Systems Lecture 6 51/57
52 Signal Reconstruction arzaneh Abdollahi Signal and Systems Lecture 6 52/57
53 Signal Reconstruction arzaneh Abdollahi Signal and Systems Lecture 6 53/57
54 Aliasing arzaneh Abdollahi Signal and Systems Lecture 6 54/57
55 C/D Converter arzaneh Abdollahi Signal and Systems Lecture 6 55/57
56 C/D Converter arzaneh Abdollahi Signal and Systems Lecture 6 56/57
57 D/C Converter arzaneh Abdollahi Signal and Systems Lecture 6 57/57
Signals and Systems Lecture 6: Fourier Applications
Signals and Systems Lecture 6: Fourier Applications Farzaneh Abdollahi Department of Electrical Engineering Amirkabir University of Technology Winter 2012 arzaneh Abdollahi Signal and Systems Lecture 6
More informationFourier Transform Analysis of Signals and Systems
Fourier Transform Analysis of Signals and Systems Ideal Filters Filters separate what is desired from what is not desired In the signals and systems context a filter separates signals in one frequency
More informationDigital Processing of
Chapter 4 Digital Processing of Continuous-Time Signals 清大電機系林嘉文 cwlin@ee.nthu.edu.tw 03-5731152 Original PowerPoint slides prepared by S. K. Mitra 4-1-1 Digital Processing of Continuous-Time Signals Digital
More informationDigital Processing of Continuous-Time Signals
Chapter 4 Digital Processing of Continuous-Time Signals 清大電機系林嘉文 cwlin@ee.nthu.edu.tw 03-5731152 Original PowerPoint slides prepared by S. K. Mitra 4-1-1 Digital Processing of Continuous-Time Signals Digital
More informationECE438 - Laboratory 7a: Digital Filter Design (Week 1) By Prof. Charles Bouman and Prof. Mireille Boutin Fall 2015
Purdue University: ECE438 - Digital Signal Processing with Applications 1 ECE438 - Laboratory 7a: Digital Filter Design (Week 1) By Prof. Charles Bouman and Prof. Mireille Boutin Fall 2015 1 Introduction
More informationDigital Signal Processing
Digital Signal Processing Lecture 9 Discrete-Time Processing of Continuous-Time Signals Alp Ertürk alp.erturk@kocaeli.edu.tr Analog to Digital Conversion Most real life signals are analog signals These
More informationDSP Laboratory (EELE 4110) Lab#10 Finite Impulse Response (FIR) Filters
Islamic University of Gaza OBJECTIVES: Faculty of Engineering Electrical Engineering Department Spring-2011 DSP Laboratory (EELE 4110) Lab#10 Finite Impulse Response (FIR) Filters To demonstrate the concept
More informationCS3291: Digital Signal Processing
CS39 Exam Jan 005 //08 /BMGC University of Manchester Department of Computer Science First Semester Year 3 Examination Paper CS39: Digital Signal Processing Date of Examination: January 005 Answer THREE
More informationFinal Exam Solutions June 14, 2006
Name or 6-Digit Code: PSU Student ID Number: Final Exam Solutions June 14, 2006 ECE 223: Signals & Systems II Dr. McNames Keep your exam flat during the entire exam. If you have to leave the exam temporarily,
More informationDigital Filters IIR (& Their Corresponding Analog Filters) Week Date Lecture Title
http://elec3004.com Digital Filters IIR (& Their Corresponding Analog Filters) 2017 School of Information Technology and Electrical Engineering at The University of Queensland Lecture Schedule: Week Date
More informationExperiment 4- Finite Impulse Response Filters
Experiment 4- Finite Impulse Response Filters 18 February 2009 Abstract In this experiment we design different Finite Impulse Response filters and study their characteristics. 1 Introduction The transfer
More informationFrequency Response Analysis
Frequency Response Analysis Continuous Time * M. J. Roberts - All Rights Reserved 2 Frequency Response * M. J. Roberts - All Rights Reserved 3 Lowpass Filter H( s) = ω c s + ω c H( jω ) = ω c jω + ω c
More informationThe University of Texas at Austin Dept. of Electrical and Computer Engineering Final Exam
The University of Texas at Austin Dept. of Electrical and Computer Engineering Final Exam Date: December 18, 2017 Course: EE 313 Evans Name: Last, First The exam is scheduled to last three hours. Open
More informationF I R Filter (Finite Impulse Response)
F I R Filter (Finite Impulse Response) Ir. Dadang Gunawan, Ph.D Electrical Engineering University of Indonesia The Outline 7.1 State-of-the-art 7.2 Type of Linear Phase Filter 7.3 Summary of 4 Types FIR
More informationNH 67, Karur Trichy Highways, Puliyur C.F, Karur District DEPARTMENT OF INFORMATION TECHNOLOGY DIGITAL SIGNAL PROCESSING UNIT 3
NH 67, Karur Trichy Highways, Puliyur C.F, 639 114 Karur District DEPARTMENT OF INFORMATION TECHNOLOGY DIGITAL SIGNAL PROCESSING UNIT 3 IIR FILTER DESIGN Structure of IIR System design of Discrete time
More informationLECTURER NOTE SMJE3163 DSP
LECTURER NOTE SMJE363 DSP (04/05-) ------------------------------------------------------------------------- Week3 IIR Filter Design -------------------------------------------------------------------------
More informationFrequency-Response Masking FIR Filters
Frequency-Response Masking FIR Filters Georg Holzmann June 14, 2007 With the frequency-response masking technique it is possible to design sharp and linear phase FIR filters. Therefore a model filter and
More information(i) Understanding of the characteristics of linear-phase finite impulse response (FIR) filters
FIR Filter Design Chapter Intended Learning Outcomes: (i) Understanding of the characteristics of linear-phase finite impulse response (FIR) filters (ii) Ability to design linear-phase FIR filters according
More informationELEC-C5230 Digitaalisen signaalinkäsittelyn perusteet
ELEC-C5230 Digitaalisen signaalinkäsittelyn perusteet Lecture 10: Summary Taneli Riihonen 16.05.2016 Lecture 10 in Course Book Sanjit K. Mitra, Digital Signal Processing: A Computer-Based Approach, 4th
More information(i) Understanding of the characteristics of linear-phase finite impulse response (FIR) filters
FIR Filter Design Chapter Intended Learning Outcomes: (i) Understanding of the characteristics of linear-phase finite impulse response (FIR) filters (ii) Ability to design linear-phase FIR filters according
More informationDesign of FIR Filters
Design of FIR Filters Elena Punskaya www-sigproc.eng.cam.ac.uk/~op205 Some material adapted from courses by Prof. Simon Godsill, Dr. Arnaud Doucet, Dr. Malcolm Macleod and Prof. Peter Rayner 1 FIR as a
More information6.02 Fall 2012 Lecture #13
6.02 Fall 2012 Lecture #13 Frequency response Filters Spectral content 6.02 Fall 2012 Lecture 13 Slide #1 Sinusoidal Inputs and LTI Systems h[n] A very important property of LTI systems or channels: If
More informationOutline. Discrete time signals. Impulse sampling z-transform Frequency response Stability INF4420. Jørgen Andreas Michaelsen Spring / 37 2 / 37
INF4420 Discrete time signals Jørgen Andreas Michaelsen Spring 2013 1 / 37 Outline Impulse sampling z-transform Frequency response Stability Spring 2013 Discrete time signals 2 2 / 37 Introduction More
More informationBrief Introduction to Signals & Systems. Phani Chavali
Brief Introduction to Signals & Systems Phani Chavali Outline Signals & Systems Continuous and discrete time signals Properties of Systems Input- Output relation : Convolution Frequency domain representation
More informationECE503: Digital Filter Design Lecture 9
ECE503: Digital Filter Design Lecture 9 D. Richard Brown III WPI 26-March-2012 WPI D. Richard Brown III 26-March-2012 1 / 33 Lecture 9 Topics Within the broad topic of digital filter design, we are going
More information4. Design of Discrete-Time Filters
4. Design of Discrete-Time Filters 4.1. Introduction (7.0) 4.2. Frame of Design of IIR Filters (7.1) 4.3. Design of IIR Filters by Impulse Invariance (7.1) 4.4. Design of IIR Filters by Bilinear Transformation
More informationGEORGIA INSTITUTE OF TECHNOLOGY. SCHOOL of ELECTRICAL and COMPUTER ENGINEERING. ECE 2026 Summer 2018 Lab #8: Filter Design of FIR Filters
GEORGIA INSTITUTE OF TECHNOLOGY SCHOOL of ELECTRICAL and COMPUTER ENGINEERING ECE 2026 Summer 2018 Lab #8: Filter Design of FIR Filters Date: 19. Jul 2018 Pre-Lab: You should read the Pre-Lab section of
More informationContinuous-Time Signal Analysis FOURIER Transform - Applications DR. SIGIT PW JAROT ECE 2221
Continuous-Time Signal Analysis FOURIER Transform - Applications DR. SIGIT PW JAROT ECE 2221 Inspiring Message from Imam Shafii You will not acquire knowledge unless you have 6 (SIX) THINGS Intelligence
More informationLecture 2 Review of Signals and Systems: Part 1. EE4900/EE6720 Digital Communications
EE4900/EE6420: Digital Communications 1 Lecture 2 Review of Signals and Systems: Part 1 Block Diagrams of Communication System Digital Communication System 2 Informatio n (sound, video, text, data, ) Transducer
More informationLaboratory Assignment 5 Amplitude Modulation
Laboratory Assignment 5 Amplitude Modulation PURPOSE In this assignment, you will explore the use of digital computers for the analysis, design, synthesis, and simulation of an amplitude modulation (AM)
More informationDigital Filters FIR and IIR Systems
Digital Filters FIR and IIR Systems ELEC 3004: Systems: Signals & Controls Dr. Surya Singh (Some material adapted from courses by Russ Tedrake and Elena Punskaya) Lecture 16 elec3004@itee.uq.edu.au http://robotics.itee.uq.edu.au/~elec3004/
More informationEE 311 February 13 and 15, 2019 Lecture 10
EE 311 February 13 and 15, 219 Lecture 1 Figure 4.22 The top figure shows a quantized sinusoid as the darker stair stepped curve. The bottom figure shows the quantization error. The quantized signal to
More informationMultirate Digital Signal Processing
Multirate Digital Signal Processing Basic Sampling Rate Alteration Devices Up-sampler - Used to increase the sampling rate by an integer factor Down-sampler - Used to increase the sampling rate by an integer
More informationCHAPTER 14. Introduction to Frequency Selective Circuits
CHAPTER 14 Introduction to Frequency Selective Circuits Frequency-selective circuits Varying source frequency on circuit voltages and currents. The result of this analysis is the frequency response of
More informationSignals and Systems. Lecture 13 Wednesday 6 th December 2017 DR TANIA STATHAKI
Signals and Systems Lecture 13 Wednesday 6 th December 2017 DR TANIA STATHAKI READER (ASSOCIATE PROFFESOR) IN SIGNAL PROCESSING IMPERIAL COLLEGE LONDON Continuous time versus discrete time Continuous time
More informationSignal processing preliminaries
Signal processing preliminaries ISMIR Graduate School, October 4th-9th, 2004 Contents: Digital audio signals Fourier transform Spectrum estimation Filters Signal Proc. 2 1 Digital signals Advantages of
More informationUNIT IV FIR FILTER DESIGN 1. How phase distortion and delay distortion are introduced? The phase distortion is introduced when the phase characteristics of a filter is nonlinear within the desired frequency
More informationElectric Circuit Theory
Electric Circuit Theory Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Chapter 15 Active Filter Circuits Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Contents and Objectives 3 Chapter Contents 15.1 First-Order
More informationSampling of Continuous-Time Signals. Reference chapter 4 in Oppenheim and Schafer.
Sampling of Continuous-Time Signals Reference chapter 4 in Oppenheim and Schafer. Periodic Sampling of Continuous Signals T = sampling period fs = sampling frequency when expressing frequencies in radians
More informationLinear Time-Invariant Systems
Linear Time-Invariant Systems Modules: Wideband True RMS Meter, Audio Oscillator, Utilities, Digital Utilities, Twin Pulse Generator, Tuneable LPF, 100-kHz Channel Filters, Phase Shifter, Quadrature Phase
More informationInfinite Impulse Response (IIR) Filter. Ikhwannul Kholis, ST., MT. Universitas 17 Agustus 1945 Jakarta
Infinite Impulse Response (IIR) Filter Ihwannul Kholis, ST., MT. Universitas 17 Agustus 1945 Jaarta The Outline 8.1 State-of-the-art 8.2 Coefficient Calculation Method for IIR Filter 8.2.1 Pole-Zero Placement
More informationPROBLEM SET 6. Note: This version is preliminary in that it does not yet have instructions for uploading the MATLAB problems.
PROBLEM SET 6 Issued: 2/32/19 Due: 3/1/19 Reading: During the past week we discussed change of discrete-time sampling rate, introducing the techniques of decimation and interpolation, which is covered
More informationEECS 216 Winter 2008 Lab 2: FM Detector Part I: Intro & Pre-lab Assignment
EECS 216 Winter 2008 Lab 2: Part I: Intro & Pre-lab Assignment c Kim Winick 2008 1 Introduction In the first few weeks of EECS 216, you learned how to determine the response of an LTI system by convolving
More informationCHAPTER 6 Frequency Response, Bode. Plots, and Resonance
CHAPTER 6 Frequency Response, Bode Plots, and Resonance CHAPTER 6 Frequency Response, Bode Plots, and Resonance 1. State the fundamental concepts of Fourier analysis. 2. Determine the output of a filter
More informationFilters. Phani Chavali
Filters Phani Chavali Filters Filtering is the most common signal processing procedure. Used as echo cancellers, equalizers, front end processing in RF receivers Used for modifying input signals by passing
More informationy(n)= Aa n u(n)+bu(n) b m sin(2πmt)= b 1 sin(2πt)+b 2 sin(4πt)+b 3 sin(6πt)+ m=1 x(t)= x = 2 ( b b b b
Exam 1 February 3, 006 Each subquestion is worth 10 points. 1. Consider a periodic sawtooth waveform x(t) with period T 0 = 1 sec shown below: (c) x(n)= u(n). In this case, show that the output has the
More informationChapter 6 CONTINUOUS-TIME, IMPULSE-MODULATED, AND DISCRETE-TIME SIGNALS. 6.6 Sampling Theorem 6.7 Aliasing 6.8 Interrelations
Chapter 6 CONTINUOUS-TIME, IMPULSE-MODULATED, AND DISCRETE-TIME SIGNALS 6.6 Sampling Theorem 6.7 Aliasing 6.8 Interrelations Copyright c 2005- Andreas Antoniou Victoria, BC, Canada Email: aantoniou@ieee.org
More informationECE 5650/4650 Exam II November 20, 2018 Name:
ECE 5650/4650 Exam II November 0, 08 Name: Take-Home Exam Honor Code This being a take-home exam a strict honor code is assumed. Each person is to do his/her own work. Bring any questions you have about
More informationDigital Signal Processing
Digital Signal Processing System Analysis and Design Paulo S. R. Diniz Eduardo A. B. da Silva and Sergio L. Netto Federal University of Rio de Janeiro CAMBRIDGE UNIVERSITY PRESS Preface page xv Introduction
More informationFinal Exam Practice Questions for Music 421, with Solutions
Final Exam Practice Questions for Music 4, with Solutions Elementary Fourier Relationships. For the window w = [/,,/ ], what is (a) the dc magnitude of the window transform? + (b) the magnitude at half
More informationFinal Exam Solutions June 7, 2004
Name: Final Exam Solutions June 7, 24 ECE 223: Signals & Systems II Dr. McNames Write your name above. Keep your exam flat during the entire exam period. If you have to leave the exam temporarily, close
More informationSpeech, music, images, and video are examples of analog signals. Each of these signals is characterized by its bandwidth, dynamic range, and the
Speech, music, images, and video are examples of analog signals. Each of these signals is characterized by its bandwidth, dynamic range, and the nature of the signal. For instance, in the case of audio
More informationUNIT-II MYcsvtu Notes agk
UNIT-II agk UNIT II Infinite Impulse Response Filter design (IIR): Analog & Digital Frequency transformation. Designing by impulse invariance & Bilinear method. Butterworth and Chebyshev Design Method.
More informationElectrical & Computer Engineering Technology
Electrical & Computer Engineering Technology EET 419C Digital Signal Processing Laboratory Experiments by Masood Ejaz Experiment # 1 Quantization of Analog Signals and Calculation of Quantized noise Objective:
More informationSTATION NUMBER: LAB SECTION: Filters. LAB 6: Filters ELECTRICAL ENGINEERING 43/100 INTRODUCTION TO MICROELECTRONIC CIRCUITS
Lab 6: Filters YOUR EE43/100 NAME: Spring 2013 YOUR PARTNER S NAME: YOUR SID: YOUR PARTNER S SID: STATION NUMBER: LAB SECTION: Filters LAB 6: Filters Pre- Lab GSI Sign- Off: Pre- Lab: /40 Lab: /60 Total:
More informationThe University of Texas at Austin Dept. of Electrical and Computer Engineering Midterm #2
The University of Texas at Austin Dept. of Electrical and Computer Engineering Midterm #2 Date: November 18, 2010 Course: EE 313 Evans Name: Last, First The exam is scheduled to last 75 minutes. Open books
More informationDesign of a Sharp Linear-Phase FIR Filter Using the α-scaled Sampling Kernel
Proceedings of the 6th WSEAS International Conference on SIGNAL PROCESSING, Dallas, Texas, USA, March 22-24, 2007 129 Design of a Sharp Linear-Phase FIR Filter Using the -scaled Sampling Kernel K.J. Kim,
More informationCorso di DATI e SEGNALI BIOMEDICI 1. Carmelina Ruggiero Laboratorio MedInfo
Corso di DATI e SEGNALI BIOMEDICI 1 Carmelina Ruggiero Laboratorio MedInfo Digital Filters Function of a Filter In signal processing, the functions of a filter are: to remove unwanted parts of the signal,
More informationEELE503. Modern filter design. Filter Design - Introduction
EELE503 Modern filter design Filter Design - Introduction A filter will modify the magnitude or phase of a signal to produce a desired frequency response or time response. One way to classify ideal filters
More informationPHYS225 Lecture 15. Electronic Circuits
PHYS225 Lecture 15 Electronic Circuits Last lecture Difference amplifier Differential input; single output Good CMRR, accurate gain, moderate input impedance Instrumentation amplifier Differential input;
More information2.1 BASIC CONCEPTS Basic Operations on Signals Time Shifting. Figure 2.2 Time shifting of a signal. Time Reversal.
1 2.1 BASIC CONCEPTS 2.1.1 Basic Operations on Signals Time Shifting. Figure 2.2 Time shifting of a signal. Time Reversal. 2 Time Scaling. Figure 2.4 Time scaling of a signal. 2.1.2 Classification of Signals
More information6.02 Fall 2013 Lecture #14
6.02 Fall 2013 Lecture #14 Spectral content of signals via the DTFT 6.02 Fall 2013 Lecture 14 Slide #1 Determining h[n] from H(Ω) H(Ω) = m h[m]e jωm Multiply both sides by e jωn and integrate over a (contiguous)
More informationModule 3 : Sampling and Reconstruction Problem Set 3
Module 3 : Sampling and Reconstruction Problem Set 3 Problem 1 Shown in figure below is a system in which the sampling signal is an impulse train with alternating sign. The sampling signal p(t), the Fourier
More informationIIR Filter Design Chapter Intended Learning Outcomes: (i) Ability to design analog Butterworth filters
IIR Filter Design Chapter Intended Learning Outcomes: (i) Ability to design analog Butterworth filters (ii) Ability to design lowpass IIR filters according to predefined specifications based on analog
More informationActive Filter Design Techniques
Active Filter Design Techniques 16.1 Introduction What is a filter? A filter is a device that passes electric signals at certain frequencies or frequency ranges while preventing the passage of others.
More informationIntuitive Guide to Fourier Analysis. Charan Langton Victor Levin
Intuitive Guide to Fourier Analysis Charan Langton Victor Levin Much of this book relies on math developed by important persons in the field over the last 2 years. When known or possible, the authors have
More informationChapter 9. Chapter 9 275
Chapter 9 Chapter 9: Multirate Digital Signal Processing... 76 9. Decimation... 76 9. Interpolation... 8 9.. Linear Interpolation... 85 9.. Sampling rate conversion by Non-integer factors... 86 9.. Illustration
More informationSignals and Filtering
FILTERING OBJECTIVES The objectives of this lecture are to: Introduce signal filtering concepts Introduce filter performance criteria Introduce Finite Impulse Response (FIR) filters Introduce Infinite
More informationDepartment of Electronic Engineering NED University of Engineering & Technology. LABORATORY WORKBOOK For the Course SIGNALS & SYSTEMS (TC-202)
Department of Electronic Engineering NED University of Engineering & Technology LABORATORY WORKBOOK For the Course SIGNALS & SYSTEMS (TC-202) Instructor Name: Student Name: Roll Number: Semester: Batch:
More informationChapter 7 Filter Design Techniques. Filter Design Techniques
Chapter 7 Filter Design Techniques Page 1 Outline 7.0 Introduction 7.1 Design of Discrete Time IIR Filters 7.2 Design of FIR Filters Page 2 7.0 Introduction Definition of Filter Filter is a system that
More informationESE531 Spring University of Pennsylvania Department of Electrical and System Engineering Digital Signal Processing
University of Pennsylvania Department of Electrical and System Engineering Digital Signal Processing ESE531, Spring 2017 Final Project: Audio Equalization Wednesday, Apr. 5 Due: Tuesday, April 25th, 11:59pm
More informationContinuous-Time Analog Filters
ENGR 4333/5333: Digital Signal Processing Continuous-Time Analog Filters Chapter 2 Dr. Mohamed Bingabr University of Central Oklahoma Outline Frequency Response of an LTIC System Signal Transmission through
More informationFinal Exam. EE313 Signals and Systems. Fall 1999, Prof. Brian L. Evans, Unique No
Final Exam EE313 Signals and Systems Fall 1999, Prof. Brian L. Evans, Unique No. 14510 December 11, 1999 The exam is scheduled to last 50 minutes. Open books and open notes. You may refer to your homework
More informationII Year (04 Semester) EE6403 Discrete Time Systems and Signal Processing
Class Subject Code Subject II Year (04 Semester) EE6403 Discrete Time Systems and Signal Processing 1.CONTENT LIST: Introduction to Unit I - Signals and Systems 2. SKILLS ADDRESSED: Listening 3. OBJECTIVE
More informationChapter 5 Window Functions. periodic with a period of N (number of samples). This is observed in table (3.1).
Chapter 5 Window Functions 5.1 Introduction As discussed in section (3.7.5), the DTFS assumes that the input waveform is periodic with a period of N (number of samples). This is observed in table (3.1).
More informationECE 301, final exam of the session of Prof. Chih-Chun Wang Saturday 10:20am 12:20pm, December 20, 2008, STEW 130,
ECE 301, final exam of the session of Prof. Chih-Chun Wang Saturday 10:20am 12:20pm, December 20, 2008, STEW 130, 1. Enter your name, student ID number, e-mail address, and signature in the space provided
More informationDigital Filters IIR (& Their Corresponding Analog Filters) 4 April 2017 ELEC 3004: Systems 1. Week Date Lecture Title
http://elec3004.com Digital Filters IIR (& Their Corresponding Analog Filters) 4 April 017 ELEC 3004: Systems 1 017 School of Information Technology and Electrical Engineering at The University of Queensland
More informationPerformance Analysis of FIR Filter Design Using Reconfigurable Mac Unit
Volume 4 Issue 4 December 2016 ISSN: 2320-9984 (Online) International Journal of Modern Engineering & Management Research Website: www.ijmemr.org Performance Analysis of FIR Filter Design Using Reconfigurable
More informationGeorge Mason University Signals and Systems I Spring 2016
George Mason University Signals and Systems I Spring 2016 Laboratory Project #4 Assigned: Week of March 14, 2016 Due Date: Laboratory Section, Week of April 4, 2016 Report Format and Guidelines for Laboratory
More informationCopyright S. K. Mitra
1 In many applications, a discrete-time signal x[n] is split into a number of subband signals by means of an analysis filter bank The subband signals are then processed Finally, the processed subband signals
More informationINF4420 Switched capacitor circuits Outline
INF4420 Switched capacitor circuits Spring 2012 1 / 54 Outline Switched capacitor introduction MOSFET as an analog switch z-transform Switched capacitor integrators 2 / 54 Introduction Discrete time analog
More informationDIGITAL FILTERS. !! Finite Impulse Response (FIR) !! Infinite Impulse Response (IIR) !! Background. !! Matlab functions AGC DSP AGC DSP
DIGITAL FILTERS!! Finite Impulse Response (FIR)!! Infinite Impulse Response (IIR)!! Background!! Matlab functions 1!! Only the magnitude approximation problem!! Four basic types of ideal filters with magnitude
More informationSIGNALS AND SYSTEMS LABORATORY 13: Digital Communication
SIGNALS AND SYSTEMS LABORATORY 13: Digital Communication INTRODUCTION Digital Communication refers to the transmission of binary, or digital, information over analog channels. In this laboratory you will
More informationChapter 1 INTRODUCTION TO DIGITAL SIGNAL PROCESSING 1.6 Analog Filters 1.7 Applications of Analog Filters
Chapter 1 INTRODUCTION TO DIGITAL SIGNAL PROCESSING 1.6 Analog Filters 1.7 Applications of Analog Filters Copyright c 2005 Andreas Antoniou Victoria, BC, Canada Email: aantoniou@ieee.org July 14, 2018
More informationCHAPTER 8 ANALOG FILTERS
ANALOG FILTERS CHAPTER 8 ANALOG FILTERS SECTION 8.: INTRODUCTION 8. SECTION 8.2: THE TRANSFER FUNCTION 8.5 THE SPLANE 8.5 F O and Q 8.7 HIGHPASS FILTER 8.8 BANDPASS FILTER 8.9 BANDREJECT (NOTCH) FILTER
More informationFREQUENCY RESPONSE AND PASSIVE FILTERS LABORATORY
FREQUENCY RESPONSE AND PASSIVE FILTERS LABORATORY In this experiment we will analytically determine and measure the frequency response of networks containing resistors, AC source/sources, and energy storage
More informationCOURSE OUTLINE. Introduction Signals and Noise Filtering: LPF1 Constant-Parameter Low Pass Filters Sensors and associated electronics
Sensors, Signals and Noise COURSE OUTLINE Introduction Signals and Noise Filtering: LPF Constant-Parameter Low Pass Filters Sensors and associated electronics Signal Recovery, 207/208 LPF- Constant-Parameter
More informationChapter 7 Single-Sideband Modulation (SSB) and Frequency Translation
Chapter 7 Single-Sideband Modulation (SSB) and Frequency Translation Contents Slide 1 Single-Sideband Modulation Slide 2 SSB by DSBSC-AM and Filtering Slide 3 SSB by DSBSC-AM and Filtering (cont.) Slide
More informationLecture Schedule: Week Date Lecture Title
http://elec3004.org Sampling & More 2014 School of Information Technology and Electrical Engineering at The University of Queensland Lecture Schedule: Week Date Lecture Title 1 2-Mar Introduction 3-Mar
More informationDSP First. Laboratory Exercise #7. Everyday Sinusoidal Signals
DSP First Laboratory Exercise #7 Everyday Sinusoidal Signals This lab introduces two practical applications where sinusoidal signals are used to transmit information: a touch-tone dialer and amplitude
More informationVolume 3 Signal Processing Reference Manual
Contents Volume 3 Signal Processing Reference Manual Contents 1 Sampling analogue signals 1.1 Introduction...1-1 1.2 Selecting a sampling speed...1-1 1.3 References...1-5 2 Digital filters 2.1 Introduction...2-1
More informationINF4420. Switched capacitor circuits. Spring Jørgen Andreas Michaelsen
INF4420 Switched capacitor circuits Spring 2012 Jørgen Andreas Michaelsen (jorgenam@ifi.uio.no) Outline Switched capacitor introduction MOSFET as an analog switch z-transform Switched capacitor integrators
More informationzt ( ) = Ae find f(t)=re( zt ( )), g(t)= Im( zt ( )), and r(t), and θ ( t) if z(t)=r(t) e
Homework # Fundamentals Review Homework or EECS 562 (As needed or plotting you can use Matlab or another sotware tool or your choice) π. Plot x ( t) = 2cos(2π5 t), x ( t) = 2cos(2π5( t.25)), and x ( t)
More informationSignal Processing. Naureen Ghani. December 9, 2017
Signal Processing Naureen Ghani December 9, 27 Introduction Signal processing is used to enhance signal components in noisy measurements. It is especially important in analyzing time-series data in neuroscience.
More informationDigital Video and Audio Processing. Winter term 2002/ 2003 Computer-based exercises
Digital Video and Audio Processing Winter term 2002/ 2003 Computer-based exercises Rudolf Mester Institut für Angewandte Physik Johann Wolfgang Goethe-Universität Frankfurt am Main 6th November 2002 Chapter
More informationCommunication Channels
Communication Channels wires (PCB trace or conductor on IC) optical fiber (attenuation 4dB/km) broadcast TV (50 kw transmit) voice telephone line (under -9 dbm or 110 µw) walkie-talkie: 500 mw, 467 MHz
More informationSampling, interpolation and decimation issues
S-72.333 Postgraduate Course in Radiocommunications Fall 2000 Sampling, interpolation and decimation issues Jari Koskelo 28.11.2000. Introduction The topics of this presentation are sampling, interpolation
More informationSampling and Signal Processing
Sampling and Signal Processing Sampling Methods Sampling is most commonly done with two devices, the sample-and-hold (S/H) and the analog-to-digital-converter (ADC) The S/H acquires a continuous-time signal
More informationEECE 301 Signals & Systems Prof. Mark Fowler
EECE 31 Signals & Systems Prof. Mark Fowler Note Set #19 C-T Systems: Frequency-Domain Analysis of Systems Reading Assignment: Section 5.2 of Kamen and Heck 1/17 Course Flow Diagram The arrows here show
More informationECE 556 BASICS OF DIGITAL SPEECH PROCESSING. Assıst.Prof.Dr. Selma ÖZAYDIN Spring Term-2017 Lecture 2
ECE 556 BASICS OF DIGITAL SPEECH PROCESSING Assıst.Prof.Dr. Selma ÖZAYDIN Spring Term-2017 Lecture 2 Analog Sound to Digital Sound Characteristics of Sound Amplitude Wavelength (w) Frequency ( ) Timbre
More information